| ########## |
| User guide |
| ########## |
| How to compile and run TF-M and example test application for CoreLink |
| SSE-200 subsystem on the MPS2 board and on the Fast Model(FVP). |
| |
| Follow :doc:`build instruction <tfm_build_instruction>` to build the binaries. |
| Follow :doc:`secure boot <tfm_secure_boot>` to build the binaries with or |
| without BL2 bootloader. |
| |
| **************************************************************** |
| Execute TF-M example and regression tests on MPS2 boards and FVP |
| **************************************************************** |
| The BL2 bootloader and TF-M example application and tests run correctly on |
| SMM-SSE-200 for MPS2 (AN521) and on the Fixed Virtual Platform model |
| FVP_MPS2_AEMv8M version 11.2.23. |
| |
| To run the example code on FVP_MPS2_AEMv8M |
| ========================================== |
| Using FVP_MPS2_AEMv8M provided by DS-5 v5.27.1. |
| |
| .. Note:: |
| FVP reference guide can be found |
| `here <https://developer.arm.com/docs/100966/latest>`__ |
| |
| Example application and regression tests without BL2 bootloader |
| --------------------------------------------------------------- |
| Add ``tfm_s.axf`` and ``tfm_ns.axf`` to symbol files in Debug Configuration |
| menu. |
| |
| .. code-block:: bash |
| |
| <DS5_PATH>/sw/models/bin/FVP_MPS2_AEMv8M \ |
| --parameter fvp_mps2.platform_type=2 \ |
| --parameter cpu0.baseline=0 \ |
| --parameter cpu0.INITVTOR_S=0x10000000 \ |
| --parameter cpu0.semihosting-enable=0 \ |
| --parameter fvp_mps2.DISABLE_GATING=0 \ |
| --parameter fvp_mps2.telnetterminal0.start_telnet=1 \ |
| --parameter fvp_mps2.telnetterminal1.start_telnet=0 \ |
| --parameter fvp_mps2.telnetterminal2.start_telnet=0 \ |
| --parameter fvp_mps2.telnetterminal0.quiet=0 \ |
| --parameter fvp_mps2.telnetterminal1.quiet=1 \ |
| --parameter fvp_mps2.telnetterminal2.quiet=1 \ |
| --application cpu0=<build_dir>/install/outputs/fvp/tfm_s.axf \ |
| --data cpu0=<build_dir>/install/outputs/fvp/tfm_ns.bin@0x00100000 |
| |
| Example application and regression tests with BL2 bootloader |
| ------------------------------------------------------------ |
| To test TF-M with bootloader, one must apply the following changes: |
| |
| - Add ``mcuboot.axf`` to symbol files in DS-5 in Debug Configuration |
| menu. |
| - Replace the last two lines of the previous command with this: |
| |
| .. code-block:: bash |
| |
| --application cpu0=<build_dir>/install/outputs/fvp/mcuboot.axf \ |
| --data cpu0=<build_dir>/install/outputs/fvp/tfm_s_ns_signed.bin@0x10080000 |
| |
| Test software upgrade with BL2 bootloader |
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ |
| BL2 bootloader is mandatory to test software update. Furthermore two TF-M blob |
| must be built. Outputs of example application and regression test can be used to |
| test it. Load output of example application to the primary slot (0x10080000) and |
| output of regression test to the secondary slot (0x10180000). Add the following |
| line to the end of the previous chapter: |
| |
| .. code-block:: bash |
| |
| --data cpu0=<build_dir>/install/outputs/fvp/tfm_s_ns_signed.bin@0x10180000 |
| |
| To run the example code on SSE 200 FPGA on MPS2 board |
| ===================================================== |
| FPGA image is available to download |
| `here <https://developer.arm.com/products/system-design/development-boards/cortex-m-prototyping-systems/mps2>`__ |
| |
| To run BL2 bootloader and TF-M example application and tests in the MPS2 board, |
| it is required to have SMM-SSE-200 for MPS2 (AN521) image in the MPS2 board SD |
| card. The image should be located in |
| ``<MPS2 device name>/MB/HBI0263<board revision letter>/AN521`` |
| |
| The MPS2 board tested is HBI0263C referred also as MPS2+. |
| |
| .. Warning:: |
| |
| If you change the exe names, MPS2 expects file names in 8.3 format. |
| |
| Example application |
| ------------------- |
| #. Copy ``mcuboot.bin`` and ``tfm_sign.bin`` files from |
| ``<build_dir>/install/outputs/AN521/`` to |
| ``<MPS2 device name>/SOFTWARE/`` |
| #. Open ``<MPS2 device name>/MB/HBI0263C/AN521/images.txt`` |
| #. Update the ``AN521/images.txt`` file as follows:: |
| |
| TITLE: Versatile Express Images Configuration File |
| [IMAGES] |
| TOTALIMAGES: 2 ;Number of Images (Max: 32) |
| IMAGE0ADDRESS: 0x10000000 |
| IMAGE0FILE: \Software\mcuboot.bin ; BL2 bootloader |
| IMAGE1ADDRESS: 0x10080000 |
| IMAGE1FILE: \Software\tfm_sign.bin ; TF-M example application binary blob |
| |
| #. Close ``<MPS2 device name>/MB/HBI0263C/AN521/images.txt`` |
| #. Unmount/eject the ``<MPS2 device name>`` unit |
| #. Reset the board to execute the TF-M example application |
| #. After completing the procedure you should be able to visualize on the serial |
| port (baud 115200 8n1) the following messages:: |
| |
| [INF] Starting bootloader |
| [INF] Image 0: magic=good, copy_done=0xff, image_ok=0xff |
| [INF] Scratch: magic=bad, copy_done=0x5, image_ok=0xcf |
| [INF] Boot source: primary slot |
| [INF] Swap type: none |
| [INF] Bootloader chainload address offset: 0x80000 |
| [INF] Jumping to the first image slot |
| [Sec Thread] Secure image initializing! |
| |
| Regression tests |
| ---------------- |
| After completing the procedure you should be able to visualize on the serial |
| port (baud 115200 8n1) the following messages:: |
| |
| [INF] Starting bootloader |
| [INF] Image 0: magic=good, copy_done=0xff, image_ok=0xff |
| [INF] Scratch: magic=bad, copy_done=0x5, image_ok=0xcf |
| [INF] Boot source: primary slot |
| [INF] Swap type: none |
| [INF] Bootloader chainload address offset: 0x80000 |
| [INF] Jumping to the first image slot |
| [Sec Thread] Secure image initializing! |
| |
| #### Execute test suites for the secure storage service #### |
| Running Test Suite SST secure interface tests (TFM_SST_TEST_2XXX)... |
| |
| > Executing 'TFM_SST_TEST_2001' |
| Description: 'Create interface' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2002' |
| Description: 'Get handle interface (DEPRECATED)' |
| This test is DEPRECATED and the test execution was SKIPPED |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2003' |
| Description: 'Get handle with null handle pointer (DEPRECATED)' |
| This test is DEPRECATED and the test execution was SKIPPED |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2004' |
| Description: 'Write interface' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2005' |
| Description: 'Read interface' |
| .... |
| |
| .. Note:: |
| |
| SST reliability tests take a few minutes to run on the MPS2. |
| |
| Example application without BL2 bootloader |
| ------------------------------------------ |
| #. Copy ``tfm_s.bin`` and ``tfm_ns.bin`` files from |
| ``<build_dir>/install/outputs/AN521/`` to |
| ``<MPS2 device name>/SOFTWARE/`` |
| #. Open ``<MPS2 device name>/MB/HBI0263C/AN521/images.txt`` |
| #. Update the ``AN521/images.txt`` file as follows:: |
| |
| TITLE: Versatile Express Images Configuration File |
| [IMAGES] |
| TOTALIMAGES: 2 ;Number of Images (Max: 32) |
| IMAGE0ADDRESS: 0x10000000 |
| IMAGE0FILE: \Software\tfm_s.bin ; Secure code |
| IMAGE1ADDRESS: 0x00100000 |
| IMAGE1FILE: \Software\tfm_ns.bin ; Non-secure code |
| |
| #. Close ``<MPS2 device name>/MB/HBI0263C/AN521/images.txt`` |
| #. Unmount/eject the ``<MPS2 device name>`` unit |
| #. Reset the board to execute the TF-M example application |
| #. After completing the procedure you should be able to visualize on the serial |
| port (baud 115200 8n1) the following messages:: |
| |
| [Sec Thread] Secure image initializing! |
| |
| Regression tests without BL2 bootloader |
| --------------------------------------- |
| After completing the procedure you should be able to visualize on the serial |
| port (baud 115200 8n1) the following messages:: |
| |
| [Sec Thread] Secure image initializing! |
| |
| #### Execute test suites for the secure storage service #### |
| Running Test Suite SST secure interface tests (TFM_SST_TEST_2XXX)... |
| |
| > Executing 'TFM_SST_TEST_2001' |
| Description: 'Create interface' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2002' |
| Description: 'Get handle interface (DEPRECATED)' |
| This test is DEPRECATED and the test execution was SKIPPED |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2003' |
| Description: 'Get handle with null handle pointer (DEPRECATED)' |
| This test is DEPRECATED and the test execution was SKIPPED |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2004' |
| Description: 'Write interface' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2005' |
| Description: 'Read interface' |
| .... |
| |
| ******************************************************************* |
| Execute TF-M example and regression tests on Musca test chip boards |
| ******************************************************************* |
| .. Note:: |
| |
| Before executing any images on Musca-B1 board, please check the |
| :doc:`target platform readme </platform/ext/target/musca_b1/readme>` |
| to have the correct setup. |
| |
| Example application with BL2 bootloader |
| ======================================= |
| |
| #. Create a unified hex file comprising of both ``mcuboot.bin`` and |
| ``tfm_sign.bin``. |
| |
| - For Musca-A |
| |
| - Windows:: |
| |
| srec_cat.exe bl2\ext\mcuboot\mcuboot.bin -Binary -offset 0x200000 tfm_sign.bin -Binary -offset 0x220000 -o tfm.hex -Intel |
| |
| - Linux:: |
| |
| srec_cat bl2/ext/mcuboot/mcuboot.bin -Binary -offset 0x200000 tfm_sign.bin -Binary -offset 0x220000 -o tfm.hex -Intel |
| |
| - For Musca-B1 |
| |
| - Windows:: |
| |
| srec_cat.exe bl2\ext\mcuboot\mcuboot.bin -Binary -offset 0xA000000 tfm_sign.bin -Binary -offset 0xA020000 -o tfm.hex -Intel |
| |
| - Linux:: |
| |
| srec_cat bl2/ext/mcuboot/mcuboot.bin -Binary -offset 0xA000000 tfm_sign.bin -Binary -offset 0xA020000 -o tfm.hex -Intel |
| |
| #. Power up the Musca board by connecting it to a computer with a USB lead. |
| Press the ``PBON`` button if the green ``ON`` LED does not immediately turn |
| on. The board should appear as a USB drive. |
| #. Copy ``tfm.hex`` to the USB drive. The orange ``PWR`` LED should start |
| blinking. |
| #. Once the ``PWR`` LED stops blinking, power cycle or reset the board to boot |
| from the new image. |
| #. After completing the procedure you should see the following messages on the |
| DAPLink UART (baud 115200 8n1):: |
| |
| [INF] Starting bootloader |
| [INF] Image 0: magic=good, copy_done=0xff, image_ok=0xff |
| [INF] Scratch: magic=bad, copy_done=0x5, image_ok=0xd9 |
| [INF] Boot source: primary slot |
| [INF] Swap type: none |
| [INF] Bootloader chainload address offset: 0x20000 |
| [INF] Jumping to the first image slot |
| [Sec Thread] Secure image initializing! |
| |
| Regression tests with BL2 bootloader |
| ==================================== |
| After completing the procedure you should see the following messages on the |
| DAPLink UART (baud 115200 8n1):: |
| |
| [INF] Starting bootloader |
| [INF] Image 0: magic=good, copy_done=0xff, image_ok=0xff |
| [INF] Scratch: magic=bad, copy_done=0x5, image_ok=0x9 |
| [INF] Boot source: primary slot |
| [INF] Swap type: none |
| [INF] Bootloader chainload address offset: 0x20000 |
| [INF] Jumping to the first image slot |
| [Sec Thread] Secure image initializing! |
| |
| #### Execute test suites for the secure storage service #### |
| Running Test Suite SST secure interface tests (TFM_SST_TEST_2XXX)... |
| > Executing 'TFM_SST_TEST_2001' |
| Description: 'Create interface' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2002' |
| Description: 'Get handle interface (DEPRECATED)' |
| This test is DEPRECATED and the test execution was SKIPPED |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2003' |
| Description: 'Get handle with null handle pointer (DEPRECATED)' |
| This test is DEPRECATED and the test execution was SKIPPED |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2004' |
| Description: 'Get attributes interface' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2005' |
| Description: 'Get attributes with null attributes struct pointer' |
| .... |
| |
| Example application or regression tests on Musca-B1 without BL2 bootloader |
| ========================================================================== |
| |
| Follow the above procedures, but create a unified hex file out of ``tfm_s.bin`` |
| and ``tfm_ns.bin``: |
| |
| - Windows:: |
| |
| srec_cat.exe app\secure_fw\tfm_s.bin -Binary -offset 0xA000000 app\tfm_ns.bin -Binary -offset 0xA060000 -o tfm.hex -Intel |
| |
| - Linux:: |
| |
| srec_cat app/secure_fw/tfm_s.bin -Binary -offset 0xA000000 app/tfm_ns.bin -Binary -offset 0xA060000 -o tfm.hex -Intel |
| |
| ******************************************************** |
| Execute TF-M example and regression tests on MPS3 boards |
| ******************************************************** |
| |
| To run the example code on CoreLink SSE-200 Subsystem for MPS3 (AN524) |
| ====================================================================== |
| FPGA image is available to download `here <https://www.arm.com/products/development-tools/development-boards/mps3>`__ |
| |
| To run BL2 bootloader and TF-M example application and tests in the MPS3 board, |
| it is required to have SMM-SSE-200 for MPS3 (AN524) image in the MPS3 board |
| SD card. The image should be located in |
| ``<MPS3 device name>/MB/HBI<BoardNumberBoardrevision>/AN524`` |
| |
| And the current boot memory for AN524 is QSPI flash, so you need to set the |
| correct REMAP option in |
| ``<MPS3 device name>/MB/HBI<BoardNumberBoardrevision>/AN524/an524_v1.txt`` |
| |
| :: |
| |
| REMAP: QSPI ;REMAP boot device BRAM/QSPI. Must match REMAPVAL below. |
| REMAPVAL: 1 ;REMAP register value e.g. 0-BRAM. 1-QSPI |
| |
| The MPS3 board tested is HBI0309B. |
| |
| .. Note:: |
| If you change the exe names, MPS3 expects file names in 8.3 format. |
| |
| Example application |
| ------------------- |
| #. Copy ``mcuboot.bin`` and ``tfm_sign.bin`` files from |
| build dir to ``<MPS3 device name>/SOFTWARE/`` |
| #. Open ``<MPS3 device name>/MB/HBI0309B/AN524/images.txt`` |
| #. Update the ``images.txt`` file as follows:: |
| |
| TITLE: Arm MPS3 FPGA prototyping board Images Configuration File |
| |
| [IMAGES] |
| TOTALIMAGES: 2 ;Number of Images (Max: 32) |
| |
| IMAGE0UPDATE: AUTO ;Image Update:NONE/AUTO/FORCE |
| IMAGE0ADDRESS: 0x00000000 ;Please select the required executable program |
| IMAGE0FILE: \SOFTWARE\mcuboot.bin |
| IMAGE1UPDATE: AUTO |
| IMAGE1ADDRESS: 0x00040000 |
| IMAGE1FILE: \SOFTWARE\tfm_sign.bin |
| |
| #. Close ``<MPS3 device name>/MB/HBI0309B/AN524/images.txt`` |
| #. Unmount/eject the ``<MPS3 device name>`` unit |
| #. Reset the board to execute the TF-M example application |
| #. After completing the procedure you should be able to visualize on the serial |
| port (baud 115200 8n1) the following messages:: |
| |
| [INF] Starting bootloader |
| [INF] Image 0: magic= good, copy_done=0xff, image_ok=0xff |
| [INF] Scratch: magic=unset, copy_done=0x43, image_ok=0xff |
| [INF] Boot source: slot 0 |
| [INF] Swap type: none |
| [INF] Bootloader chainload address offset: 0x40000 |
| [INF] Jumping to the first image slot |
| [Sec Thread] Secure image initializing! |
| |
| Regression tests |
| ---------------- |
| After completing the procedure you should be able to visualize on the serial |
| port (baud 115200 8n1) the following messages:: |
| |
| [INF] Starting bootloader |
| [INF] Image 0: magic= good, copy_done=0xff, image_ok=0xff |
| [INF] Scratch: magic=unset, copy_done=0x9, image_ok=0xff |
| [INF] Boot source: slot 0 |
| [INF] Swap type: none |
| [INF] Bootloader chainload address offset: 0x40000 |
| [INF] Jumping to the first image slot |
| [Sec Thread] Secure image initializing! |
| |
| #### Execute test suites for the Secure area #### |
| Running Test Suite PSA protected storage S interface tests (TFM_SST_TEST_2XXX)... |
| > Executing 'TFM_SST_TEST_2001' |
| Description: 'Set interface' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2002' |
| Description: 'Set interface with create flags' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2003' |
| Description: 'Set interface with NULL data pointer' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2004' |
| Description: 'Set interface with invalid data length' |
| TEST PASSED! |
| .... |
| |
| .. Note:: |
| Some of the attestation tests take a few minutes to run on the MPS3. |
| |
| Example application without BL2 bootloader |
| ------------------------------------------ |
| #. Copy ``tfm_s.bin`` and ``tfm_ns.bin`` files from |
| build dir to ``<MPS3 device name>/SOFTWARE/`` |
| #. Open ``<MPS3 device name>/MB/HBI0309B/AN524/images.txt`` |
| #. Update the ``images.txt`` file as follows:: |
| |
| TITLE: Arm MPS3 FPGA prototyping board Images Configuration File |
| |
| [IMAGES] |
| TOTALIMAGES: 2 ;Number of Images (Max: 32) |
| |
| IMAGE0UPDATE: AUTO ;Image Update:NONE/AUTO/FORCE |
| IMAGE0ADDRESS: 0x00000000 ;Please select the required executable program |
| IMAGE0FILE: \SOFTWARE\tfm_s.bin |
| IMAGE1UPDATE: AUTO |
| IMAGE1ADDRESS: 0x00080000 |
| IMAGE1FILE: \SOFTWARE\tfm_ns.bin |
| |
| #. Close ``<MPS3 device name>/MB/HBI0309B/AN521/images.txt`` |
| #. Unmount/eject the ``<MPS3 device name>`` unit |
| #. Reset the board to execute the TF-M example application |
| #. After completing the procedure you should be able to visualize on the serial |
| port (baud 115200 8n1) the following messages:: |
| |
| [Sec Thread] Secure image initializing! |
| |
| Regression tests without BL2 bootloader |
| --------------------------------------- |
| After completing the procedure you should be able to visualize on the serial |
| port (baud 115200 8n1) the following messages:: |
| |
| [Sec Thread] Secure image initializing! |
| |
| #### Execute test suites for the Secure area #### |
| Running Test Suite PSA protected storage S interface tests (TFM_SST_TEST_2XXX)... |
| > Executing 'TFM_SST_TEST_2001' |
| Description: 'Set interface' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2002' |
| Description: 'Set interface with create flags' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2003' |
| Description: 'Set interface with NULL data pointer' |
| TEST PASSED! |
| > Executing 'TFM_SST_TEST_2004' |
| Description: 'Set interface with invalid data length' |
| TEST PASSED! |
| .... |
| |
| Firmware upgrade and image validation with BL2 bootloader |
| ========================================================= |
| High level operation of BL2 bootloader and instructions for testing firmware |
| upgrade is described in :doc:`secure boot <tfm_secure_boot>`. |
| |
| -------------- |
| |
| *Copyright (c) 2017-2019, Arm Limited. All rights reserved.* |