Platform: Remove Musca_A platform code (Deprecation)
This patch removes Musca A board from platform
code-base and documentation.
Signed-off-by: Minos Galanakis <minos.galanakis@arm.com>
Change-Id: I8479a18faa769e112792830c9e64127e72843aaa
diff --git a/docs/getting_started/tfm_integration_guide.rst b/docs/getting_started/tfm_integration_guide.rst
index 6ab7a19..a37a4cb 100644
--- a/docs/getting_started/tfm_integration_guide.rst
+++ b/docs/getting_started/tfm_integration_guide.rst
@@ -23,7 +23,6 @@
- Cortex-M23 IoT Kit subsystem for MPS2+ (AN519)
- Corstone-300 Ecosystem FVP (Cortex-M55 SSE-300 MPS2+)
- Corstone-300 Ethos-U55 FVP (Cortex-M55 plus Ethos-U55 SSE-300 MPS3)
-- Musca-A test chip board (Cortex-M33 SSE-200 subsystem)
- Musca-B1 test chip board (Cortex-M33 SSE-200 subsystem)
- Musca-S1 test chip board (Cortex-M33 SSE-200 subsystem)
- CoreLink SSE-200 Subsystem for MPS3 (AN524)
@@ -44,9 +43,6 @@
More information about subsystems supported by the MPS3 board can be found in:
`MPS3 homepage <https://developer.arm.com/products/system-design/development-boards/fpga-prototyping-boards/mps3>`__
-More information about the Musca-A test chip board can be found in:
-`Musca-A homepage <https://developer.arm.com/products/system-design/development-boards/iot-test-chips-and-boards/musca-a-test-chip-board>`__
-
More information about the Musca-B1 test chip board can be found in:
`Musca-B1 homepage <https://www.arm.com/products/development-tools/development-boards/musca-b1-iot>`__
diff --git a/docs/getting_started/tfm_secure_boot.rst b/docs/getting_started/tfm_secure_boot.rst
index 0764956..95d3f68 100644
--- a/docs/getting_started/tfm_secure_boot.rst
+++ b/docs/getting_started/tfm_secure_boot.rst
@@ -202,7 +202,7 @@
RAM Loading firmware upgrade
============================
-Musca-A supports an image upgrade mode that is separate to the other (overwrite,
+Musca-S supports an image upgrade mode that is separate to the other (overwrite,
swapping and dirext-xip) modes. This is the ``RAM load`` mode (please refer
to the table below). Like the direct-xip mode, this selects the newest image
by reading the image version numbers in the image headers, but instead of
@@ -238,8 +238,6 @@
+---------------------+-----------------+---------------+----------+----------------+--------------+
| LPC55S69 | Yes | Yes | No | Yes | No |
+---------------------+-----------------+---------------+----------+----------------+--------------+
-| Musca-A | No | No | No | No | Yes |
-+---------------------+-----------------+---------------+----------+----------------+--------------+
| Musca-B1 | Yes | Yes | Yes | Yes | No |
+---------------------+-----------------+---------------+----------+----------------+--------------+
| Musca-S1 | Yes | Yes | Yes | Yes | No |
@@ -758,21 +756,21 @@
(either in the configuration file or through the command line), and then specify
a destination load address in RAM where the image can be copied to and executed
from. The ``IMAGE_LOAD_ADDRESS`` macro must be specified in the target dependent
-files, for example with Musca-A, its ``flash_layout.h`` file in the ``platform``
-folder should include ``#define IMAGE_LOAD_ADDRESS #0x10020000``
+files, for example with Musca-S, its ``flash_layout.h`` file in the ``platform``
+folder should include ``#define IMAGE_LOAD_ADDRESS #0xA0020000``
-Executing firmware upgrade on Musca-A board
+Executing firmware upgrade on Musca-S board
--------------------------------------------
After two images have been built, they can be concatenated to create the
combined image using ``srec_cat``:
- Linux::
- srec_cat bin/bl2.bin -Binary -offset 0x200000 tfm_sign_old.bin -Binary -offset 0x220000 tfm_sign_new.bin -Binary -offset 0x320000 -o tfm.hex -Intel
+ srec_cat bin/bl2.bin -Binary -offset 0xA000000 tfm_sign_old.bin -Binary -offset 0xA020000 tfm_sign_new.bin -Binary -offset 0xA100000 -o tfm.hex -Intel
- Windows::
- srec_cat.exe bin\bl2.bin -Binary -offset 0x200000 tfm_sign_old.bin -Binary -offset 0x220000 tfm_sign_new.bin -Binary -offset 0x320000 -o tfm.hex -Intel
+ srec_cat.exe bin\bl2.bin -Binary -offset 0xA000000 tfm_sign_old.bin -Binary -offset 0xA020000 tfm_sign_new.bin -Binary -offset 0xA100000 -o tfm.hex -Intel
The following message will be shown in case of successful firmware upgrade when,
RAM loading is enabled, notice that image with higher version number
@@ -783,8 +781,8 @@
[INF] Starting bootloader
[INF] Image 0: version=0.0.0.1, magic= good, image_ok=0x3
[INF] Image 1: version=0.0.0.2, magic= good, image_ok=0x3
- [INF] Image has been copied from the secondary slot in flash to SRAM address 0x10020000
- [INF] Booting image from SRAM at address 0x10020000
+ [INF] Image has been copied from the secondary slot in flash to SRAM address 0xA0020000
+ [INF] Booting image from SRAM at address 0xA0020000
[INF] Bootloader chainload address offset: 0x20000
[INF] Jumping to the first image slot
[Sec Thread] Secure image initializing!
diff --git a/docs/getting_started/tfm_user_guide.rst b/docs/getting_started/tfm_user_guide.rst
index 1a2de50..55648f4 100644
--- a/docs/getting_started/tfm_user_guide.rst
+++ b/docs/getting_started/tfm_user_guide.rst
@@ -233,16 +233,6 @@
#. Create a unified hex file comprising of both ``bl2.bin`` and
``tfm_s_ns_signed.bin``.
- - For Musca-A
-
- - Windows::
-
- srec_cat.exe bin\bl2.bin -Binary -offset 0x200000 bin\tfm_s_ns_signed.bin -Binary -offset 0x220000 -o tfm.hex -Intel
-
- - Linux::
-
- srec_cat bin/bl2.bin -Binary -offset 0x200000 bin/tfm_s_ns_signed.bin -Binary -offset 0x220000 -o tfm.hex -Intel
-
- For Musca-B1
- Windows::
@@ -398,12 +388,7 @@
Another way this can be achieved is by using ``srec_cat`` with the ``-fill``
parameter to fill the corresponding area in the binary with the erase value
- of the flash (``0xFF``). For example, for Musca-A the command for
- concatenating the ``bl2`` and ``tfm_s_ns_signed`` binaries would become::
-
- srec_cat bin/bl2.bin -Binary -offset 0x200000 \
- bin/tfm_s_ns_signed.bin -Binary -offset 0x220000 \
- -fill 0xFF 0x420000 0x425000 -o tfm.hex -Intel
+ of the flash (``0xFF``).
Refer to the platform flash layout for appropriate addresses to erase on
other platforms.
diff --git a/docs/introduction/readme.rst b/docs/introduction/readme.rst
index 71b0b4e..f57996d 100644
--- a/docs/introduction/readme.rst
+++ b/docs/introduction/readme.rst
@@ -127,8 +127,6 @@
<https://developer.arm.com/products/system-design/development-boards/cortex-m-prototyping-systems/mps2>`_
- `Fast model FVP_MPS2_AEMv8M (AN521).
<https://developer.arm.com/products/system-design/fixed-virtual-platforms>`_
- - `Musca-A test chip board.
- <https://developer.arm.com/products/system-design/development-boards/iot-test-chips-and-boards/musca-a-test-chip-board>`_
- `Musca-B1 test chip board.
<https://developer.arm.com/products/system-design/development-boards/iot-test-chips-and-boards/musca-b-test-chip-board>`_
- `Musca-S1 test chip board.
diff --git a/platform/ext/target/musca_a/CMSIS_Driver/Config/RTE_Device.h b/platform/ext/target/musca_a/CMSIS_Driver/Config/RTE_Device.h
deleted file mode 100644
index d1901ce..0000000
--- a/platform/ext/target/musca_a/CMSIS_Driver/Config/RTE_Device.h
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * Copyright (c) 2018-2020 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-//-------- <<< Use Configuration Wizard in Context Menu >>> --------------------
-
-#ifndef __RTE_DEVICE_H
-#define __RTE_DEVICE_H
-
-// <e> MPC (Memory Protection Controller) [Driver_ISRAM0_MPC]
-// <i> Configuration settings for Driver_ISRAM0_MPC in component ::Drivers:MPC
-#define RTE_ISRAM0_MPC 1
-// </e> MPC (Memory Protection Controller) [Driver_ISRAM0_MPC]
-
-// <e> MPC (Memory Protection Controller) [Driver_ISRAM1_MPC]
-// <i> Configuration settings for Driver_SRAM1_MPC in component ::Drivers:MPC
-#define RTE_ISRAM1_MPC 1
-// </e> MPC (Memory Protection Controller) [Driver_ISRAM1_MPC]
-
-// <e> MPC (Memory Protection Controller) [Driver_ISRAM2_MPC]
-// <i> Configuration settings for Driver_ISRAM2_MPC in component ::Drivers:MPC
-#define RTE_ISRAM2_MPC 1
-// </e> MPC (Memory Protection Controller) [Driver_ISRAM2_MPC]
-
-// <e> MPC (Memory Protection Controller) [Driver_ISRAM3_MPC]
-// <i> Configuration settings for Driver_SRAM2_MPC in component ::Drivers:MPC
-#define RTE_ISRAM3_MPC 1
-// </e> MPC (Memory Protection Controller) [Driver_SRAM3_MPC]
-
-// <e> MPC (Memory Protection Controller) [Driver_CODE_SRAM_MPC]
-// <i> Configuration settings for Driver_CODE_SRAM_MPC in component ::Drivers:MPC
-#define RTE_CODE_SRAM_MPC 1
-// </e> MPC (Memory Protection Controller) [Driver_CODE_SRAM_MPC]
-
-// <e> MPC (Memory Protection Controller) [Driver_QSPI_MPC]
-// <i> Configuration settings for Driver_QSPI_MPC in component ::Drivers:MPC
-#define RTE_QSPI_MPC 1
-// </e> MPC (Memory Protection Controller) [Driver_QSPI_MPC]
-
-// <e> USART (Universal synchronous - asynchronous receiver transmitter) [Driver_USART0]
-// <i> Configuration settings for Driver_USART0 in component ::Drivers:USART
-#define RTE_USART0 0
-// </e> USART (Universal synchronous - asynchronous receiver transmitter) [Driver_USART0]
-
-// <e> USART (Universal synchronous - asynchronous receiver transmitter) [Driver_USART1]
-// <i> Configuration settings for Driver_USART1 in component ::Drivers:USART
-#define RTE_USART1 1
-// </e> USART (Universal synchronous - asynchronous receiver transmitter) [Driver_USART1]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_AHB_PPC0]
-// <i> Configuration settings for Driver_AHB_PPC0 in component ::Drivers:PPC
-#define RTE_AHB_PPC0 1
-// </e> PPC (Peripheral Protection Controller) [Driver_AHB_PPC0]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_AHB_PPCEXP0]
-// <i> Configuration settings for Driver_AHB_PPCEXP0 in component ::Drivers:PPC
-#define RTE_AHB_PPCEXP0 0
-// </e> PPC (Peripheral Protection Controller) [Driver_AHB_PPCEXP0]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_AHB_PPCEXP1]
-// <i> Configuration settings for Driver_AHB_PPCEXP1 in component ::Drivers:PPC
-#define RTE_AHB_PPCEXP1 0
-// </e> PPC (Peripheral Protection Controller) [Driver_AHB_PPCEXP1]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_AHB_PPCEXP2]
-// <i> Configuration settings for Driver_AHB_PPCEXP2 in component ::Drivers:PPC
-#define RTE_AHB_PPCEXP2 0
-// </e> PPC (Peripheral Protection Controller) [Driver_AHB_PPCEXP2]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_AHB_PPCEXP3]
-// <i> Configuration settings for Driver_AHB_PPCEXP3 in component ::Drivers:PPC
-#define RTE_AHB_PPCEXP3 0
-// </e> PPC (Peripheral Protection Controller) [Driver_AHB_PPCEXP3]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_APB_PPC0]
-// <i> Configuration settings for Driver_APB_PPC0 in component ::Drivers:PPC
-#define RTE_APB_PPC0 1
-// </e> PPC (Peripheral Protection Controller) [Driver_APB_PPC0]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_APB_PPC1]
-// <i> Configuration settings for Driver_APB_PPC1 in component ::Drivers:PPC
-#define RTE_APB_PPC1 1
-// </e> PPC (Peripheral Protection Controller) [Driver_APB_PPC1]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_APB_PPCEXP0]
-// <i> Configuration settings for Driver_APB_PPCEXP0 in component ::Drivers:PPC
-#define RTE_APB_PPCEXP0 0
-// </e> PPC (Peripheral Protection Controller) [Driver_APB_PPCEXP0]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_APB_PPCEXP1]
-// <i> Configuration settings for Driver_APB_PPCEXP1 in component ::Drivers:PPC
-#define RTE_APB_PPCEXP1 0
-// </e> PPC (Peripheral Protection Controller) [Driver_APB_PPCEXP1]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_APB_PPCEXP2]
-// <i> Configuration settings for Driver_APB_PPCEXP2 in component ::Drivers:PPC
-#define RTE_APB_PPCEXP2 0
-// </e> PPC (Peripheral Protection Controller) [Driver_APB_PPCEXP2]
-
-// <e> PPC (Peripheral Protection Controller) [Driver_APB_PPCEXP3]
-// <i> Configuration settings for Driver_APB_PPCEXP3 in component ::Drivers:PPC
-#define RTE_APB_PPCEXP3 0
-// </e> PPC (Peripheral Protection Controller) [Driver_APB_PPCEXP3]
-
-// <e> FLASH (Flash Memory) [Driver_FLASH0]
-// <i> Configuration settings for Driver_FLASH0 in component ::Drivers:FLASH
-#define RTE_QSPI_FLASH0 1
-// </e> FLASH (Flash Memory) [Driver_FLASH0]
-
-#endif /* __RTE_DEVICE_H */
diff --git a/platform/ext/target/musca_a/CMSIS_Driver/Config/cmsis_driver_config.h b/platform/ext/target/musca_a/CMSIS_Driver/Config/cmsis_driver_config.h
deleted file mode 100644
index 8ccd505..0000000
--- a/platform/ext/target/musca_a/CMSIS_Driver/Config/cmsis_driver_config.h
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * Copyright (c) 2018-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#ifndef __CMSIS_DRIVER_CONFIG_H__
-#define __CMSIS_DRIVER_CONFIG_H__
-
-#include "device_cfg.h"
-#include "device_definition.h"
-#include "platform_description.h"
-#include "RTE_Device.h"
-#include "target_cfg.h"
-
-#define UART0_DEV UART0_PL011_DEV_NS
-#define UART1_DEV UART1_PL011_DEV_NS
-
-/* Note: On Musca-A all expansion peripherals, including the flash controller,
- * are configured by a single PPC bit position (see section 3.3.6 of the Musca-A
- * Technical Reference Manual for details). This is set to non-secure to allow
- * the UART (and other peripherals) to be accessed from NS code, so the flash
- * controller must also be accessed through its non-secure alias.
- */
-#define FLASH0_DEV MT25QL_DEV_NS
-
-#define MPC_ISRAM0_DEV MPC_ISRAM0_DEV_S
-#define MPC_ISRAM1_DEV MPC_ISRAM1_DEV_S
-#define MPC_ISRAM2_DEV MPC_ISRAM2_DEV_S
-#define MPC_ISRAM3_DEV MPC_ISRAM3_DEV_S
-#define MPC_CODE_SRAM_DEV MPC_CODE_SRAM_DEV_S
-#define MPC_QSPI_DEV MPC_QSPI_DEV_S
-
-#define AHB_PPC0_DEV AHB_PPC0_DEV_S
-#define AHB_PPCEXP0_DEV AHB_PPCEXP0_DEV_S
-#define AHB_PPCEXP1_DEV AHB_PPCEXP1_DEV_S
-#define AHB_PPCEXP2_DEV AHB_PPCEXP2_DEV_S
-#define AHB_PPCEXP3_DEV AHB_PPCEXP3_DEV_S
-#define APB_PPC0_DEV APB_PPC0_DEV_S
-#define APB_PPC1_DEV APB_PPC1_DEV_S
-#define APB_PPCEXP0_DEV APB_PPCEXP0_DEV_S
-#define APB_PPCEXP1_DEV APB_PPCEXP1_DEV_S
-#define APB_PPCEXP2_DEV APB_PPCEXP2_DEV_S
-#define APB_PPCEXP3_DEV APB_PPCEXP3_DEV_S
-
-#define MUSCA_A1_SCC_DEV MUSCA_A1_SCC_DEV_S
-
-#endif /* __CMSIS_DRIVER_CONFIG_H__ */
diff --git a/platform/ext/target/musca_a/CMSIS_Driver/Driver_MPC.c b/platform/ext/target/musca_a/CMSIS_Driver/Driver_MPC.c
deleted file mode 100644
index ca6f374..0000000
--- a/platform/ext/target/musca_a/CMSIS_Driver/Driver_MPC.c
+++ /dev/null
@@ -1,1304 +0,0 @@
-/*
- * Copyright (c) 2016-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-#include "Driver_MPC.h"
-
-#include "cmsis_driver_config.h"
-#include "RTE_Device.h"
-
-/* driver version */
-#define ARM_MPC_DRV_VERSION ARM_DRIVER_VERSION_MAJOR_MINOR(1,0)
-
-/* Driver Version */
-static const ARM_DRIVER_VERSION DriverVersion = {
- ARM_MPC_API_VERSION,
- ARM_MPC_DRV_VERSION
-};
-
-static ARM_DRIVER_VERSION ARM_MPC_GetVersion(void)
-{
- return DriverVersion;
-}
-
-/*
- * \brief Translates error codes from native API to CMSIS API.
- *
- * \param[in] err Error code to translate (\ref mpc_sie200_error_t).
- *
- * \return Returns CMSIS error code.
- */
-static int32_t error_trans(enum mpc_sie200_error_t err)
-{
- switch(err) {
- case MPC_SIE200_ERR_NONE:
- return ARM_DRIVER_OK;
- case MPC_SIE200_INVALID_ARG:
- return ARM_DRIVER_ERROR_PARAMETER;
- case MPC_SIE200_NOT_INIT:
- return ARM_MPC_ERR_NOT_INIT;
- case MPC_SIE200_ERR_NOT_IN_RANGE:
- return ARM_MPC_ERR_NOT_IN_RANGE;
- case MPC_SIE200_ERR_NOT_ALIGNED:
- return ARM_MPC_ERR_NOT_ALIGNED;
- case MPC_SIE200_ERR_INVALID_RANGE:
- return ARM_MPC_ERR_INVALID_RANGE;
- case MPC_SIE200_ERR_RANGE_SEC_ATTR_NON_COMPATIBLE:
- return ARM_MPC_ERR_RANGE_SEC_ATTR_NON_COMPATIBLE;
- default:
- return ARM_MPC_ERR_UNSPECIFIED;
- }
-}
-
-#if (RTE_ISRAM0_MPC)
-/* Ranges controlled by this ISRAM0_MPC */
-static const struct mpc_sie200_memory_range_t MPC_ISRAM0_RANGE_S = {
- .base = MPC_ISRAM0_RANGE_BASE_S,
- .limit = MPC_ISRAM0_RANGE_LIMIT_S,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_SECURE
-};
-
-static const struct mpc_sie200_memory_range_t MPC_ISRAM0_RANGE_NS = {
- .base = MPC_ISRAM0_RANGE_BASE_NS,
- .limit = MPC_ISRAM0_RANGE_LIMIT_NS,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_NONSECURE
-};
-
-#define MPC_ISRAM0_RANGE_LIST_LEN 2u
-static const struct mpc_sie200_memory_range_t* MPC_ISRAM0_RANGE_LIST[MPC_ISRAM0_RANGE_LIST_LEN]=
- {&MPC_ISRAM0_RANGE_S, &MPC_ISRAM0_RANGE_NS};
-
-/* ISRAM0_MPC Driver wrapper functions */
-static int32_t ISRAM0_MPC_Initialize(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_init(&MPC_ISRAM0_DEV,
- MPC_ISRAM0_RANGE_LIST,
- MPC_ISRAM0_RANGE_LIST_LEN);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM0_MPC_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t ISRAM0_MPC_GetBlockSize(uint32_t* blk_size)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_block_size(&MPC_ISRAM0_DEV, blk_size);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM0_MPC_GetCtrlConfig(uint32_t* ctrl_val)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_ctrl(&MPC_ISRAM0_DEV, ctrl_val);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM0_MPC_SetCtrlConfig(uint32_t ctrl)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_set_ctrl(&MPC_ISRAM0_DEV, ctrl);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM0_MPC_GetRegionConfig(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR* attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_region_config(&MPC_ISRAM0_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t*)attr);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM0_MPC_ConfigRegion(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_config_region(&MPC_ISRAM0_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t)attr);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM0_MPC_EnableInterrupt(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_irq_enable(&MPC_ISRAM0_DEV);
-
- return error_trans(ret);
-}
-
-static void ISRAM0_MPC_DisableInterrupt(void)
-{
- mpc_sie200_irq_disable(&MPC_ISRAM0_DEV);
-}
-
-
-static void ISRAM0_MPC_ClearInterrupt(void)
-{
- mpc_sie200_clear_irq(&MPC_ISRAM0_DEV);
-}
-
-static uint32_t ISRAM0_MPC_InterruptState(void)
-{
- return mpc_sie200_irq_state(&MPC_ISRAM0_DEV);
-}
-
-static int32_t ISRAM0_MPC_LockDown(void)
-{
- return mpc_sie200_lock_down(&MPC_ISRAM0_DEV);
-}
-
-/* ISRAM0_MPC Driver CMSIS access structure */
-extern ARM_DRIVER_MPC Driver_ISRAM0_MPC;
-ARM_DRIVER_MPC Driver_ISRAM0_MPC = {
- .GetVersion = ARM_MPC_GetVersion,
- .Initialize = ISRAM0_MPC_Initialize,
- .Uninitialize = ISRAM0_MPC_Uninitialize,
- .GetBlockSize = ISRAM0_MPC_GetBlockSize,
- .GetCtrlConfig = ISRAM0_MPC_GetCtrlConfig,
- .SetCtrlConfig = ISRAM0_MPC_SetCtrlConfig,
- .ConfigRegion = ISRAM0_MPC_ConfigRegion,
- .GetRegionConfig = ISRAM0_MPC_GetRegionConfig,
- .EnableInterrupt = ISRAM0_MPC_EnableInterrupt,
- .DisableInterrupt = ISRAM0_MPC_DisableInterrupt,
- .ClearInterrupt = ISRAM0_MPC_ClearInterrupt,
- .InterruptState = ISRAM0_MPC_InterruptState,
- .LockDown = ISRAM0_MPC_LockDown,
-};
-#endif /* RTE_ISRAM0_MPC */
-
-#if (RTE_ISRAM1_MPC)
-/* Ranges controlled by this ISRAM1_MPC */
-static const struct mpc_sie200_memory_range_t MPC_ISRAM1_RANGE_S = {
- .base = MPC_ISRAM1_RANGE_BASE_S,
- .limit = MPC_ISRAM1_RANGE_LIMIT_S,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_SECURE
-};
-
-static const struct mpc_sie200_memory_range_t MPC_ISRAM1_RANGE_NS = {
- .base = MPC_ISRAM1_RANGE_BASE_NS,
- .limit = MPC_ISRAM1_RANGE_LIMIT_NS,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_NONSECURE
-};
-
-#define MPC_ISRAM1_RANGE_LIST_LEN 2u
-static const struct mpc_sie200_memory_range_t* MPC_ISRAM1_RANGE_LIST[MPC_ISRAM1_RANGE_LIST_LEN]=
- {&MPC_ISRAM1_RANGE_S, &MPC_ISRAM1_RANGE_NS};
-
-/* ISRAM1_MPC Driver wrapper functions */
-static int32_t ISRAM1_MPC_Initialize(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_init(&MPC_ISRAM1_DEV,
- MPC_ISRAM1_RANGE_LIST,
- MPC_ISRAM1_RANGE_LIST_LEN);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM1_MPC_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t ISRAM1_MPC_GetBlockSize(uint32_t* blk_size)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_block_size(&MPC_ISRAM1_DEV, blk_size);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM1_MPC_GetCtrlConfig(uint32_t* ctrl_val)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_ctrl(&MPC_ISRAM1_DEV, ctrl_val);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM1_MPC_SetCtrlConfig(uint32_t ctrl)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_set_ctrl(&MPC_ISRAM1_DEV, ctrl);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM1_MPC_GetRegionConfig(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR* attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_region_config(&MPC_ISRAM1_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t*)attr);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM1_MPC_ConfigRegion(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_config_region(&MPC_ISRAM1_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t)attr);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM1_MPC_EnableInterrupt(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_irq_enable(&MPC_ISRAM1_DEV);
-
- return error_trans(ret);
-}
-
-static void ISRAM1_MPC_DisableInterrupt(void)
-{
- mpc_sie200_irq_disable(&MPC_ISRAM1_DEV);
-}
-
-
-static void ISRAM1_MPC_ClearInterrupt(void)
-{
- mpc_sie200_clear_irq(&MPC_ISRAM1_DEV);
-}
-
-static uint32_t ISRAM1_MPC_InterruptState(void)
-{
- return mpc_sie200_irq_state(&MPC_ISRAM1_DEV);
-}
-
-static int32_t ISRAM1_MPC_LockDown(void)
-{
- return mpc_sie200_lock_down(&MPC_ISRAM1_DEV);
-}
-
-/* ISRAM1_MPC Driver CMSIS access structure */
-extern ARM_DRIVER_MPC Driver_ISRAM1_MPC;
-ARM_DRIVER_MPC Driver_ISRAM1_MPC = {
- .GetVersion = ARM_MPC_GetVersion,
- .Initialize = ISRAM1_MPC_Initialize,
- .Uninitialize = ISRAM1_MPC_Uninitialize,
- .GetBlockSize = ISRAM1_MPC_GetBlockSize,
- .GetCtrlConfig = ISRAM1_MPC_GetCtrlConfig,
- .SetCtrlConfig = ISRAM1_MPC_SetCtrlConfig,
- .ConfigRegion = ISRAM1_MPC_ConfigRegion,
- .GetRegionConfig = ISRAM1_MPC_GetRegionConfig,
- .EnableInterrupt = ISRAM1_MPC_EnableInterrupt,
- .DisableInterrupt = ISRAM1_MPC_DisableInterrupt,
- .ClearInterrupt = ISRAM1_MPC_ClearInterrupt,
- .InterruptState = ISRAM1_MPC_InterruptState,
- .LockDown = ISRAM1_MPC_LockDown,
-};
-#endif /* RTE_ISRAM1_MPC */
-
-#if (RTE_ISRAM2_MPC)
-/* Ranges controlled by this ISRAM2_MPC */
-static const struct mpc_sie200_memory_range_t MPC_ISRAM2_RANGE_S = {
- .base = MPC_ISRAM2_RANGE_BASE_S,
- .limit = MPC_ISRAM2_RANGE_LIMIT_S,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_SECURE
-};
-
-static const struct mpc_sie200_memory_range_t MPC_ISRAM2_RANGE_NS = {
- .base = MPC_ISRAM2_RANGE_BASE_NS,
- .limit = MPC_ISRAM2_RANGE_LIMIT_NS,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_NONSECURE
-};
-
-#define MPC_ISRAM2_RANGE_LIST_LEN 2u
-static const struct mpc_sie200_memory_range_t* MPC_ISRAM2_RANGE_LIST[MPC_ISRAM2_RANGE_LIST_LEN]=
- {&MPC_ISRAM2_RANGE_S, &MPC_ISRAM2_RANGE_NS};
-
-/* ISRAM2_MPC Driver wrapper functions */
-static int32_t ISRAM2_MPC_Initialize(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_init(&MPC_ISRAM2_DEV,
- MPC_ISRAM2_RANGE_LIST,
- MPC_ISRAM2_RANGE_LIST_LEN);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM2_MPC_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t ISRAM2_MPC_GetBlockSize(uint32_t* blk_size)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_block_size(&MPC_ISRAM2_DEV, blk_size);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM2_MPC_GetCtrlConfig(uint32_t* ctrl_val)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_ctrl(&MPC_ISRAM2_DEV, ctrl_val);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM2_MPC_SetCtrlConfig(uint32_t ctrl)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_set_ctrl(&MPC_ISRAM2_DEV, ctrl);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM2_MPC_GetRegionConfig(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR* attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_region_config(&MPC_ISRAM2_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t*)attr);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM2_MPC_ConfigRegion(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_config_region(&MPC_ISRAM2_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t)attr);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM2_MPC_EnableInterrupt(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_irq_enable(&MPC_ISRAM2_DEV);
-
- return error_trans(ret);
-}
-
-static void ISRAM2_MPC_DisableInterrupt(void)
-{
- mpc_sie200_irq_disable(&MPC_ISRAM2_DEV);
-}
-
-static void ISRAM2_MPC_ClearInterrupt(void)
-{
- mpc_sie200_clear_irq(&MPC_ISRAM2_DEV);
-}
-
-static uint32_t ISRAM2_MPC_InterruptState(void)
-{
- return mpc_sie200_irq_state(&MPC_ISRAM2_DEV);
-}
-
-static int32_t ISRAM2_MPC_LockDown(void)
-{
- return mpc_sie200_lock_down(&MPC_ISRAM2_DEV);
-}
-
-/* ISRAM2_MPC Driver CMSIS access structure */
-extern ARM_DRIVER_MPC Driver_ISRAM2_MPC;
-ARM_DRIVER_MPC Driver_ISRAM2_MPC = {
- .GetVersion = ARM_MPC_GetVersion,
- .Initialize = ISRAM2_MPC_Initialize,
- .Uninitialize = ISRAM2_MPC_Uninitialize,
- .GetBlockSize = ISRAM2_MPC_GetBlockSize,
- .GetCtrlConfig = ISRAM2_MPC_GetCtrlConfig,
- .SetCtrlConfig = ISRAM2_MPC_SetCtrlConfig,
- .ConfigRegion = ISRAM2_MPC_ConfigRegion,
- .GetRegionConfig = ISRAM2_MPC_GetRegionConfig,
- .EnableInterrupt = ISRAM2_MPC_EnableInterrupt,
- .DisableInterrupt = ISRAM2_MPC_DisableInterrupt,
- .ClearInterrupt = ISRAM2_MPC_ClearInterrupt,
- .InterruptState = ISRAM2_MPC_InterruptState,
- .LockDown = ISRAM2_MPC_LockDown,
-};
-#endif /* RTE_ISRAM2_MPC */
-
-#if (RTE_ISRAM3_MPC)
-/* Ranges controlled by this ISRAM3_MPC */
-static const struct mpc_sie200_memory_range_t MPC_ISRAM3_RANGE_S = {
- .base = MPC_ISRAM3_RANGE_BASE_S,
- .limit = MPC_ISRAM3_RANGE_LIMIT_S,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_SECURE
-};
-
-static const struct mpc_sie200_memory_range_t MPC_ISRAM3_RANGE_NS = {
- .base = MPC_ISRAM3_RANGE_BASE_NS,
- .limit = MPC_ISRAM3_RANGE_LIMIT_NS,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_NONSECURE
-};
-
-#define MPC_ISRAM3_RANGE_LIST_LEN 2u
-static const struct mpc_sie200_memory_range_t* MPC_ISRAM3_RANGE_LIST[MPC_ISRAM3_RANGE_LIST_LEN]=
- {&MPC_ISRAM3_RANGE_S, &MPC_ISRAM3_RANGE_NS};
-
-/* ISRAM3_MPC Driver wrapper functions */
-static int32_t ISRAM3_MPC_Initialize(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_init(&MPC_ISRAM3_DEV,
- MPC_ISRAM3_RANGE_LIST,
- MPC_ISRAM3_RANGE_LIST_LEN);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM3_MPC_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t ISRAM3_MPC_GetBlockSize(uint32_t* blk_size)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_block_size(&MPC_ISRAM3_DEV, blk_size);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM3_MPC_GetCtrlConfig(uint32_t* ctrl_val)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_ctrl(&MPC_ISRAM3_DEV, ctrl_val);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM3_MPC_SetCtrlConfig(uint32_t ctrl)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_set_ctrl(&MPC_ISRAM3_DEV, ctrl);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM3_MPC_GetRegionConfig(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR* attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_region_config(&MPC_ISRAM3_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t*)attr);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM3_MPC_ConfigRegion(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_config_region(&MPC_ISRAM3_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t)attr);
-
- return error_trans(ret);
-}
-
-static int32_t ISRAM3_MPC_EnableInterrupt(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_irq_enable(&MPC_ISRAM3_DEV);
-
- return error_trans(ret);
-}
-
-static void ISRAM3_MPC_DisableInterrupt(void)
-{
- mpc_sie200_irq_disable(&MPC_ISRAM3_DEV);
-}
-
-
-static void ISRAM3_MPC_ClearInterrupt(void)
-{
- mpc_sie200_clear_irq(&MPC_ISRAM3_DEV);
-}
-
-static uint32_t ISRAM3_MPC_InterruptState(void)
-{
- return mpc_sie200_irq_state(&MPC_ISRAM3_DEV);
-}
-
-static int32_t ISRAM3_MPC_LockDown(void)
-{
- return mpc_sie200_lock_down(&MPC_ISRAM3_DEV);
-}
-
-/* ISRAM3_MPC Driver CMSIS access structure */
-extern ARM_DRIVER_MPC Driver_ISRAM3_MPC;
-ARM_DRIVER_MPC Driver_ISRAM3_MPC = {
- .GetVersion = ARM_MPC_GetVersion,
- .Initialize = ISRAM3_MPC_Initialize,
- .Uninitialize = ISRAM3_MPC_Uninitialize,
- .GetBlockSize = ISRAM3_MPC_GetBlockSize,
- .GetCtrlConfig = ISRAM3_MPC_GetCtrlConfig,
- .SetCtrlConfig = ISRAM3_MPC_SetCtrlConfig,
- .ConfigRegion = ISRAM3_MPC_ConfigRegion,
- .GetRegionConfig = ISRAM3_MPC_GetRegionConfig,
- .EnableInterrupt = ISRAM3_MPC_EnableInterrupt,
- .DisableInterrupt = ISRAM3_MPC_DisableInterrupt,
- .ClearInterrupt = ISRAM3_MPC_ClearInterrupt,
- .InterruptState = ISRAM3_MPC_InterruptState,
- .LockDown = ISRAM3_MPC_LockDown,
-};
-#endif /* RTE_ISRAM3_MPC */
-
-#if (RTE_CODE_SRAM_MPC)
-/* Ranges controlled by this CODE_SRAM_MPC */
-static const struct mpc_sie200_memory_range_t MPC_CODE_SRAM_RANGE_S = {
- .base = MPC_CODE_SRAM_RANGE_BASE_S,
- .limit = MPC_CODE_SRAM_RANGE_LIMIT_S,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_SECURE
-};
-
-static const struct mpc_sie200_memory_range_t MPC_CODE_SRAM_RANGE_NS = {
- .base = MPC_CODE_SRAM_RANGE_BASE_NS,
- .limit = MPC_CODE_SRAM_RANGE_LIMIT_NS,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_NONSECURE
-};
-
-#define MPC_CODE_SRAM_RANGE_LIST_LEN 2u
-static const struct mpc_sie200_memory_range_t* MPC_CODE_SRAM_RANGE_LIST[MPC_CODE_SRAM_RANGE_LIST_LEN]=
- {&MPC_CODE_SRAM_RANGE_S, &MPC_CODE_SRAM_RANGE_NS};
-
-/* CODE_SRAM_MPC Driver wrapper functions */
-static int32_t CODE_SRAM_MPC_Initialize(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_init(&MPC_CODE_SRAM_DEV,
- MPC_CODE_SRAM_RANGE_LIST,
- MPC_CODE_SRAM_RANGE_LIST_LEN);
-
- return error_trans(ret);
-}
-
-static int32_t CODE_SRAM_MPC_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t CODE_SRAM_MPC_GetBlockSize(uint32_t* blk_size)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_block_size(&MPC_CODE_SRAM_DEV, blk_size);
-
- return error_trans(ret);
-}
-
-static int32_t CODE_SRAM_MPC_GetCtrlConfig(uint32_t* ctrl_val)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_ctrl(&MPC_CODE_SRAM_DEV, ctrl_val);
-
- return error_trans(ret);
-}
-
-static int32_t CODE_SRAM_MPC_SetCtrlConfig(uint32_t ctrl)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_set_ctrl(&MPC_CODE_SRAM_DEV, ctrl);
-
- return error_trans(ret);
-}
-
-static int32_t CODE_SRAM_MPC_GetRegionConfig(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR* attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_region_config(&MPC_CODE_SRAM_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t*)attr);
-
- return error_trans(ret);
-}
-
-static int32_t CODE_SRAM_MPC_ConfigRegion(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_config_region(&MPC_CODE_SRAM_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t)attr);
-
- return error_trans(ret);
-}
-
-static int32_t CODE_SRAM_MPC_EnableInterrupt(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_irq_enable(&MPC_CODE_SRAM_DEV);
-
- return error_trans(ret);
-}
-
-static void CODE_SRAM_MPC_DisableInterrupt(void)
-{
- mpc_sie200_irq_disable(&MPC_CODE_SRAM_DEV);
-}
-
-
-static void CODE_SRAM_MPC_ClearInterrupt(void)
-{
- mpc_sie200_clear_irq(&MPC_CODE_SRAM_DEV);
-}
-
-static uint32_t CODE_SRAM_MPC_InterruptState(void)
-{
- return mpc_sie200_irq_state(&MPC_CODE_SRAM_DEV);
-}
-
-static int32_t CODE_SRAM_MPC_LockDown(void)
-{
- return mpc_sie200_lock_down(&MPC_CODE_SRAM_DEV);
-}
-
-/* CODE_SRAM_MPC Driver CMSIS access structure */
-extern ARM_DRIVER_MPC Driver_CODE_SRAM_MPC;
-ARM_DRIVER_MPC Driver_CODE_SRAM_MPC = {
- .GetVersion = ARM_MPC_GetVersion,
- .Initialize = CODE_SRAM_MPC_Initialize,
- .Uninitialize = CODE_SRAM_MPC_Uninitialize,
- .GetBlockSize = CODE_SRAM_MPC_GetBlockSize,
- .GetCtrlConfig = CODE_SRAM_MPC_GetCtrlConfig,
- .SetCtrlConfig = CODE_SRAM_MPC_SetCtrlConfig,
- .ConfigRegion = CODE_SRAM_MPC_ConfigRegion,
- .GetRegionConfig = CODE_SRAM_MPC_GetRegionConfig,
- .EnableInterrupt = CODE_SRAM_MPC_EnableInterrupt,
- .DisableInterrupt = CODE_SRAM_MPC_DisableInterrupt,
- .ClearInterrupt = CODE_SRAM_MPC_ClearInterrupt,
- .InterruptState = CODE_SRAM_MPC_InterruptState,
- .LockDown = CODE_SRAM_MPC_LockDown,
-};
-#endif /* RTE_CODE_SRAM_MPC */
-
-#if (RTE_SSRAM1_MPC)
-/* Ranges controlled by this SSRAM1_MPC */
-static const struct mpc_sie200_memory_range_t MPC_SSRAM1_RANGE_S = {
- .base = MPC_SSRAM1_RANGE_BASE_S,
- .limit = MPC_SSRAM1_RANGE_LIMIT_S,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_SECURE
-};
-
-static const struct mpc_sie200_memory_range_t MPC_SSRAM1_RANGE_NS = {
- .base = MPC_SSRAM1_RANGE_BASE_NS,
- .limit = MPC_SSRAM1_RANGE_LIMIT_NS,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_NONSECURE
-};
-
-#define MPC_SSRAM1_RANGE_LIST_LEN 2u
-static const struct mpc_sie200_memory_range_t*
- MPC_SSRAM1_RANGE_LIST[MPC_SSRAM1_RANGE_LIST_LEN] =
- {&MPC_SSRAM1_RANGE_S, &MPC_SSRAM1_RANGE_NS};
-
-/* SSRAM1_MPC Driver wrapper functions */
-static int32_t SSRAM1_MPC_Initialize(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_init(&MPC_SSRAM1_DEV,
- MPC_SSRAM1_RANGE_LIST,
- MPC_SSRAM1_RANGE_LIST_LEN);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM1_MPC_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t SSRAM1_MPC_GetBlockSize(uint32_t* blk_size)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_block_size(&MPC_SSRAM1_DEV, blk_size);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM1_MPC_GetCtrlConfig(uint32_t* ctrl_val)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_ctrl(&MPC_SSRAM1_DEV, ctrl_val);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM1_MPC_SetCtrlConfig(uint32_t ctrl)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_set_ctrl(&MPC_SSRAM1_DEV, ctrl);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM1_MPC_GetRegionConfig(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR* attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_region_config(&MPC_SSRAM1_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t*)attr);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM1_MPC_ConfigRegion(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_config_region(&MPC_SSRAM1_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t)attr);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM1_MPC_EnableInterrupt(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_irq_enable(&MPC_SSRAM1_DEV);
-
- return error_trans(ret);
-}
-
-static void SSRAM1_MPC_DisableInterrupt(void)
-{
- mpc_sie200_irq_disable(&MPC_SSRAM1_DEV);
-}
-
-
-static void SSRAM1_MPC_ClearInterrupt(void)
-{
- mpc_sie200_clear_irq(&MPC_SSRAM1_DEV);
-}
-
-static uint32_t SSRAM1_MPC_InterruptState(void)
-{
- return mpc_sie200_irq_state(&MPC_SSRAM1_DEV);
-}
-
-static int32_t SSRAM1_MPC_LockDown(void)
-{
- return mpc_sie200_lock_down(&MPC_SSRAM1_DEV);
-}
-
-/* SSRAM1_MPC Driver CMSIS access structure */
-extern ARM_DRIVER_MPC Driver_SRAM1_MPC;
-ARM_DRIVER_MPC Driver_SRAM1_MPC = {
- .GetVersion = ARM_MPC_GetVersion,
- .Initialize = SSRAM1_MPC_Initialize,
- .Uninitialize = SSRAM1_MPC_Uninitialize,
- .GetBlockSize = SSRAM1_MPC_GetBlockSize,
- .GetCtrlConfig = SSRAM1_MPC_GetCtrlConfig,
- .SetCtrlConfig = SSRAM1_MPC_SetCtrlConfig,
- .ConfigRegion = SSRAM1_MPC_ConfigRegion,
- .GetRegionConfig = SSRAM1_MPC_GetRegionConfig,
- .EnableInterrupt = SSRAM1_MPC_EnableInterrupt,
- .DisableInterrupt = SSRAM1_MPC_DisableInterrupt,
- .ClearInterrupt = SSRAM1_MPC_ClearInterrupt,
- .InterruptState = SSRAM1_MPC_InterruptState,
- .LockDown = SSRAM1_MPC_LockDown,
-};
-#endif /* RTE_SSRAM1_MPC */
-
-#if (RTE_SSRAM2_MPC)
-/* Ranges controlled by this SSRAM2_MPC */
-static const struct mpc_sie200_memory_range_t MPC_SSRAM2_RANGE_S = {
- .base = MPC_SSRAM2_RANGE_BASE_S,
- .limit = MPC_SSRAM2_RANGE_LIMIT_S,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_SECURE
-};
-
-static const struct mpc_sie200_memory_range_t MPC_SSRAM2_RANGE_NS = {
- .base = MPC_SSRAM2_RANGE_BASE_NS,
- .limit = MPC_SSRAM2_RANGE_LIMIT_NS,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_NONSECURE
-};
-
-#define MPC_SSRAM2_RANGE_LIST_LEN 2u
-static const struct mpc_sie200_memory_range_t* MPC_SSRAM2_RANGE_LIST[MPC_SSRAM2_RANGE_LIST_LEN]=
- {&MPC_SSRAM2_RANGE_S, &MPC_SSRAM2_RANGE_NS};
-
-/* SSRAM2_MPC Driver wrapper functions */
-static int32_t SSRAM2_MPC_Initialize(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_init(&MPC_SSRAM2_DEV,
- MPC_SSRAM2_RANGE_LIST,
- MPC_SSRAM2_RANGE_LIST_LEN);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM2_MPC_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t SSRAM2_MPC_GetBlockSize(uint32_t* blk_size)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_block_size(&MPC_SSRAM2_DEV, blk_size);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM2_MPC_GetCtrlConfig(uint32_t* ctrl_val)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_ctrl(&MPC_SSRAM2_DEV, ctrl_val);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM2_MPC_SetCtrlConfig(uint32_t ctrl)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_set_ctrl(&MPC_SSRAM2_DEV, ctrl);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM2_MPC_GetRegionConfig(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR* attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_region_config(&MPC_SSRAM2_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t*)attr);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM2_MPC_ConfigRegion(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_config_region(&MPC_SSRAM2_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t)attr);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM2_MPC_EnableInterrupt(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_irq_enable(&MPC_SSRAM2_DEV);
-
- return error_trans(ret);
-}
-
-static void SSRAM2_MPC_DisableInterrupt(void)
-{
- mpc_sie200_irq_disable(&MPC_SSRAM2_DEV);
-}
-
-
-static void SSRAM2_MPC_ClearInterrupt(void)
-{
- mpc_sie200_clear_irq(&MPC_SSRAM2_DEV);
-}
-
-static uint32_t SSRAM2_MPC_InterruptState(void)
-{
- return mpc_sie200_irq_state(&MPC_SSRAM2_DEV);
-}
-
-static int32_t SSRAM2_MPC_LockDown(void)
-{
- return mpc_sie200_lock_down(&MPC_SSRAM2_DEV);
-}
-
-/* SSRAM2_MPC Driver CMSIS access structure */
-extern ARM_DRIVER_MPC Driver_SRAM2_MPC;
-ARM_DRIVER_MPC Driver_SRAM2_MPC = {
- .GetVersion = ARM_MPC_GetVersion,
- .Initialize = SSRAM2_MPC_Initialize,
- .Uninitialize = SSRAM2_MPC_Uninitialize,
- .GetBlockSize = SSRAM2_MPC_GetBlockSize,
- .GetCtrlConfig = SSRAM2_MPC_GetCtrlConfig,
- .SetCtrlConfig = SSRAM2_MPC_SetCtrlConfig,
- .ConfigRegion = SSRAM2_MPC_ConfigRegion,
- .GetRegionConfig = SSRAM2_MPC_GetRegionConfig,
- .EnableInterrupt = SSRAM2_MPC_EnableInterrupt,
- .DisableInterrupt = SSRAM2_MPC_DisableInterrupt,
- .ClearInterrupt = SSRAM2_MPC_ClearInterrupt,
- .InterruptState = SSRAM2_MPC_InterruptState,
- .LockDown = SSRAM2_MPC_LockDown,
-};
-#endif /* RTE_SSRAM2_MPC */
-
-#if (RTE_SSRAM3_MPC)
-/* Ranges controlled by this SSRAM3_MPC */
-static const struct mpc_sie200_memory_range_t MPC_SSRAM3_RANGE_S = {
- .base = MPC_SSRAM3_RANGE_BASE_S,
- .limit = MPC_SSRAM3_RANGE_LIMIT_S,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_SECURE
-};
-
-static const struct mpc_sie200_memory_range_t MPC_SSRAM3_RANGE_NS = {
- .base = MPC_SSRAM3_RANGE_BASE_NS,
- .limit = MPC_SSRAM3_RANGE_LIMIT_NS,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_NONSECURE
-};
-
-#define MPC_SSRAM3_RANGE_LIST_LEN 2u
-static const struct mpc_sie200_memory_range_t* MPC_SSRAM3_RANGE_LIST[MPC_SSRAM3_RANGE_LIST_LEN]=
- {&MPC_SSRAM3_RANGE_S, &MPC_SSRAM3_RANGE_NS};
-
-/* SSRAM3_MPC Driver wrapper functions */
-static int32_t SSRAM3_MPC_Initialize(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_init(&MPC_SSRAM3_DEV,
- MPC_SSRAM3_RANGE_LIST,
- MPC_SSRAM3_RANGE_LIST_LEN);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM3_MPC_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t SSRAM3_MPC_GetBlockSize(uint32_t* blk_size)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_block_size(&MPC_SSRAM3_DEV, blk_size);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM3_MPC_GetCtrlConfig(uint32_t* ctrl_val)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_ctrl(&MPC_SSRAM3_DEV, ctrl_val);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM3_MPC_SetCtrlConfig(uint32_t ctrl)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_set_ctrl(&MPC_SSRAM3_DEV, ctrl);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM3_MPC_GetRegionConfig(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR* attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_region_config(&MPC_SSRAM3_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t*)attr);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM3_MPC_ConfigRegion(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_config_region(&MPC_SSRAM3_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t)attr);
-
- return error_trans(ret);
-}
-
-static int32_t SSRAM3_MPC_EnableInterrupt(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_irq_enable(&MPC_SSRAM3_DEV);
-
- return error_trans(ret);
-}
-
-static void SSRAM3_MPC_DisableInterrupt(void)
-{
- mpc_sie200_irq_disable(&MPC_SSRAM3_DEV);
-}
-
-
-static void SSRAM3_MPC_ClearInterrupt(void)
-{
- mpc_sie200_clear_irq(&MPC_SSRAM3_DEV);
-}
-
-static uint32_t SSRAM3_MPC_InterruptState(void)
-{
- return mpc_sie200_irq_state(&MPC_SSRAM3_DEV);
-}
-
-static int32_t SSRAM3_MPC_LockDown(void)
-{
- return mpc_sie200_lock_down(&MPC_SSRAM3_DEV);
-}
-
-/* SSRAM3_MPC Driver CMSIS access structure */
-extern ARM_DRIVER_MPC Driver_SSRAM3_MPC;
-ARM_DRIVER_MPC Driver_SSRAM3_MPC = {
- .GetVersion = ARM_MPC_GetVersion,
- .Initialize = SSRAM3_MPC_Initialize,
- .Uninitialize = SSRAM3_MPC_Uninitialize,
- .GetBlockSize = SSRAM3_MPC_GetBlockSize,
- .GetCtrlConfig = SSRAM3_MPC_GetCtrlConfig,
- .SetCtrlConfig = SSRAM3_MPC_SetCtrlConfig,
- .ConfigRegion = SSRAM3_MPC_ConfigRegion,
- .GetRegionConfig = SSRAM3_MPC_GetRegionConfig,
- .EnableInterrupt = SSRAM3_MPC_EnableInterrupt,
- .DisableInterrupt = SSRAM3_MPC_DisableInterrupt,
- .ClearInterrupt = SSRAM3_MPC_ClearInterrupt,
- .InterruptState = SSRAM3_MPC_InterruptState,
- .LockDown = SSRAM3_MPC_LockDown,
-};
-#endif /* RTE_SSRAM3_MPC */
-
-#if (RTE_QSPI_MPC)
-/* Ranges controlled by this QSPI_MPC */
-static const struct mpc_sie200_memory_range_t MPC_QSPI_RANGE_S = {
- .base = MPC_QSPI_RANGE_BASE_S,
- .limit = MPC_QSPI_RANGE_LIMIT_S,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_SECURE
-};
-
-static const struct mpc_sie200_memory_range_t MPC_QSPI_RANGE_NS = {
- .base = MPC_QSPI_RANGE_BASE_NS,
- .limit = MPC_QSPI_RANGE_LIMIT_NS,
- .range_offset = 0,
- .attr = MPC_SIE200_SEC_ATTR_NONSECURE
-};
-
-#define MPC_QSPI_RANGE_LIST_LEN 2u
-static const struct mpc_sie200_memory_range_t* MPC_QSPI_RANGE_LIST[MPC_QSPI_RANGE_LIST_LEN]=
- {&MPC_QSPI_RANGE_S, &MPC_QSPI_RANGE_NS};
-
-/* QSPI_MPC Driver wrapper functions */
-static int32_t QSPI_MPC_Initialize(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_init(&MPC_QSPI_DEV,
- MPC_QSPI_RANGE_LIST,
- MPC_QSPI_RANGE_LIST_LEN);
-
- return error_trans(ret);
-}
-
-static int32_t QSPI_MPC_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t QSPI_MPC_GetBlockSize(uint32_t* blk_size)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_block_size(&MPC_QSPI_DEV, blk_size);
-
- return error_trans(ret);
-}
-
-static int32_t QSPI_MPC_GetCtrlConfig(uint32_t* ctrl_val)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_ctrl(&MPC_QSPI_DEV, ctrl_val);
-
- return error_trans(ret);
-}
-
-static int32_t QSPI_MPC_SetCtrlConfig(uint32_t ctrl)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_set_ctrl(&MPC_QSPI_DEV, ctrl);
-
- return error_trans(ret);
-}
-
-static int32_t QSPI_MPC_GetRegionConfig(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR* attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_get_region_config(&MPC_QSPI_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t*)attr);
-
- return error_trans(ret);
-}
-
-static int32_t QSPI_MPC_ConfigRegion(uintptr_t base,
- uintptr_t limit,
- ARM_MPC_SEC_ATTR attr)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_config_region(&MPC_QSPI_DEV, base, limit,
- (enum mpc_sie200_sec_attr_t)attr);
-
- return error_trans(ret);
-}
-
-static int32_t QSPI_MPC_EnableInterrupt(void)
-{
- enum mpc_sie200_error_t ret;
-
- ret = mpc_sie200_irq_enable(&MPC_QSPI_DEV);
-
- return error_trans(ret);
-}
-
-static void QSPI_MPC_DisableInterrupt(void)
-{
- mpc_sie200_irq_disable(&MPC_QSPI_DEV);
-}
-
-
-static void QSPI_MPC_ClearInterrupt(void)
-{
- mpc_sie200_clear_irq(&MPC_QSPI_DEV);
-}
-
-static uint32_t QSPI_MPC_InterruptState(void)
-{
- return mpc_sie200_irq_state(&MPC_QSPI_DEV);
-}
-
-static int32_t QSPI_MPC_LockDown(void)
-{
- return mpc_sie200_lock_down(&MPC_QSPI_DEV);
-}
-
-/* QSPI1_MPC Driver CMSIS access structure */
-extern ARM_DRIVER_MPC Driver_QSPI_MPC;
-ARM_DRIVER_MPC Driver_QSPI_MPC = {
- .GetVersion = ARM_MPC_GetVersion,
- .Initialize = QSPI_MPC_Initialize,
- .Uninitialize = QSPI_MPC_Uninitialize,
- .GetBlockSize = QSPI_MPC_GetBlockSize,
- .GetCtrlConfig = QSPI_MPC_GetCtrlConfig,
- .SetCtrlConfig = QSPI_MPC_SetCtrlConfig,
- .ConfigRegion = QSPI_MPC_ConfigRegion,
- .GetRegionConfig = QSPI_MPC_GetRegionConfig,
- .EnableInterrupt = QSPI_MPC_EnableInterrupt,
- .DisableInterrupt = QSPI_MPC_DisableInterrupt,
- .ClearInterrupt = QSPI_MPC_ClearInterrupt,
- .InterruptState = QSPI_MPC_InterruptState,
- .LockDown = QSPI_MPC_LockDown,
-};
-#endif /* RTE_QSPI_MPC */
diff --git a/platform/ext/target/musca_a/CMSIS_Driver/Driver_PPC.c b/platform/ext/target/musca_a/CMSIS_Driver/Driver_PPC.c
deleted file mode 100644
index efadb04..0000000
--- a/platform/ext/target/musca_a/CMSIS_Driver/Driver_PPC.c
+++ /dev/null
@@ -1,966 +0,0 @@
-/*
- * Copyright (c) 2016-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include "Driver_PPC.h"
-
-#include "cmsis_driver_config.h"
-#include "RTE_Device.h"
-
-/* Driver version */
-#define ARM_PPC_DRV_VERSION ARM_DRIVER_VERSION_MAJOR_MINOR(1,0)
-
-/* Driver Version */
-static const ARM_DRIVER_VERSION DriverVersion = {
- ARM_PPC_API_VERSION,
- ARM_PPC_DRV_VERSION
-};
-
-static ARM_DRIVER_VERSION ARM_PPC_GetVersion(void)
-{
- return DriverVersion;
-}
-
-#if (RTE_AHB_PPC0)
-/* AHB PPC0 Driver wrapper functions */
-static int32_t AHB_PPC0_Initialize(void)
-{
- ppc_sse200_init(&AHB_PPC0_DEV, AHB_PPC0);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPC0_Uninitialize(void)
-{
- /* Nothing to be done*/
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPC0_ConfigPeriph(uint8_t periph, ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&AHB_PPC0_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t AHB_PPC0_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&AHB_PPC0_DEV, periph);
-}
-
-static uint32_t AHB_PPC0_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&AHB_PPC0_DEV, periph);
-}
-
-static int32_t AHB_PPC0_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&AHB_PPC0_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void AHB_PPC0_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&AHB_PPC0_DEV);
-}
-
-static void AHB_PPC0_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&AHB_PPC0_DEV);
-}
-
-static uint32_t AHB_PPC0_InterruptState(void)
-{
- return ppc_sse200_irq_state(&AHB_PPC0_DEV);
-}
-
-/* AHB PPC0 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_AHB_PPC0;
-ARM_DRIVER_PPC Driver_AHB_PPC0 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = AHB_PPC0_Initialize,
- .Uninitialize = AHB_PPC0_Uninitialize,
- .ConfigPeriph = AHB_PPC0_ConfigPeriph,
- .IsPeriphSecure = AHB_PPC0_IsPeriphSecure,
- .IsPeriphPrivOnly = AHB_PPC0_IsPeriphPrivOnly,
- .EnableInterrupt = AHB_PPC0_EnableInterrupt,
- .DisableInterrupt = AHB_PPC0_DisableInterrupt,
- .ClearInterrupt = AHB_PPC0_ClearInterrupt,
- .InterruptState = AHB_PPC0_InterruptState
-};
-#endif /* RTE_AHB_PPC0 */
-
-#if (RTE_AHB_PPCEXP0)
-/* AHB PPCEXP0 Driver wrapper functions */
-static int32_t AHB_PPCEXP0_Initialize(void)
-{
- ppc_sse200_init(&AHB_PPCEXP0_DEV, AHB_PPC_EXP0);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPCEXP0_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPCEXP0_ConfigPeriph(uint8_t periph,
- ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&AHB_PPCEXP0_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t AHB_PPCEXP0_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&AHB_PPCEXP0_DEV, periph);
-}
-
-static uint32_t AHB_PPCEXP0_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&AHB_PPCEXP0_DEV, periph);
-}
-
-static int32_t AHB_PPCEXP0_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&AHB_PPCEXP0_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void AHB_PPCEXP0_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&AHB_PPCEXP0_DEV);
-}
-
-static void AHB_PPCEXP0_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&AHB_PPCEXP0_DEV);
-}
-
-static uint32_t AHB_PPCEXP0_InterruptState(void)
-{
- return ppc_sse200_irq_state(&AHB_PPCEXP0_DEV);
-}
-
-/* AHB PPCEXP0 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_AHB_PPCEXP0;
-ARM_DRIVER_PPC Driver_AHB_PPCEXP0 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = AHB_PPCEXP0_Initialize,
- .Uninitialize = AHB_PPCEXP0_Uninitialize,
- .ConfigPeriph = AHB_PPCEXP0_ConfigPeriph,
- .IsPeriphSecure = AHB_PPCEXP0_IsPeriphSecure,
- .IsPeriphPrivOnly = AHB_PPCEXP0_IsPeriphPrivOnly,
- .EnableInterrupt = AHB_PPCEXP0_EnableInterrupt,
- .DisableInterrupt = AHB_PPCEXP0_DisableInterrupt,
- .ClearInterrupt = AHB_PPCEXP0_ClearInterrupt,
- .InterruptState = AHB_PPCEXP0_InterruptState
-};
-#endif /* RTE_AHB_PPCEXP0 */
-
-#if (RTE_AHB_PPCEXP1)
-/* AHB PPCEXP1 Driver wrapper functions */
-static int32_t AHB_PPCEXP1_Initialize(void)
-{
- ppc_sse200_init(&AHB_PPCEXP1_DEV, AHB_PPC_EXP1);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPCEXP1_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPCEXP1_ConfigPeriph(uint8_t periph,
- ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&AHB_PPCEXP1_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t AHB_PPCEXP1_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&AHB_PPCEXP1_DEV, periph);
-}
-
-static uint32_t AHB_PPCEXP1_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&AHB_PPCEXP1_DEV, periph);
-}
-
-static int32_t AHB_PPCEXP1_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&AHB_PPCEXP1_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void AHB_PPCEXP1_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&AHB_PPCEXP1_DEV);
-}
-
-static void AHB_PPCEXP1_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&AHB_PPCEXP1_DEV);
-}
-
-static uint32_t AHB_PPCEXP1_InterruptState(void)
-{
- return ppc_sse200_irq_state(&AHB_PPCEXP1_DEV);
-}
-
-/* AHB PPCEXP1 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_AHB_PPCEXP1;
-ARM_DRIVER_PPC Driver_AHB_PPCEXP1 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = AHB_PPCEXP1_Initialize,
- .Uninitialize = AHB_PPCEXP1_Uninitialize,
- .ConfigPeriph = AHB_PPCEXP1_ConfigPeriph,
- .IsPeriphSecure = AHB_PPCEXP1_IsPeriphSecure,
- .IsPeriphPrivOnly = AHB_PPCEXP1_IsPeriphPrivOnly,
- .EnableInterrupt = AHB_PPCEXP1_EnableInterrupt,
- .DisableInterrupt = AHB_PPCEXP1_DisableInterrupt,
- .ClearInterrupt = AHB_PPCEXP1_ClearInterrupt,
- .InterruptState = AHB_PPCEXP1_InterruptState
-};
-#endif /* RTE_AHB_PPCEXP1 */
-
-#if (RTE_AHB_PPCEXP2)
-/* AHB PPCEXP2 Driver wrapper functions */
-static int32_t AHB_PPCEXP2_Initialize(void)
-{
- ppc_sse200_init(&AHB_PPCEXP2_DEV, AHB_PPC_EXP2);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPCEXP2_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPCEXP2_ConfigPeriph(uint8_t periph,
- ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&AHB_PPCEXP2_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t AHB_PPCEXP2_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&AHB_PPCEXP2_DEV, periph);
-}
-
-static uint32_t AHB_PPCEXP2_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&AHB_PPCEXP2_DEV, periph);
-}
-
-static int32_t AHB_PPCEXP2_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&AHB_PPCEXP2_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void AHB_PPCEXP2_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&AHB_PPCEXP2_DEV);
-}
-
-static void AHB_PPCEXP2_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&AHB_PPCEXP2_DEV);
-}
-
-static uint32_t AHB_PPCEXP2_InterruptState(void)
-{
- return ppc_sse200_irq_state(&AHB_PPCEXP2_DEV);
-}
-
-/* AHB PPCEXP2 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_AHB_PPCEXP2;
-ARM_DRIVER_PPC Driver_AHB_PPCEXP2 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = AHB_PPCEXP2_Initialize,
- .Uninitialize = AHB_PPCEXP2_Uninitialize,
- .ConfigPeriph = AHB_PPCEXP2_ConfigPeriph,
- .IsPeriphSecure = AHB_PPCEXP2_IsPeriphSecure,
- .IsPeriphPrivOnly = AHB_PPCEXP2_IsPeriphPrivOnly,
- .EnableInterrupt = AHB_PPCEXP2_EnableInterrupt,
- .DisableInterrupt = AHB_PPCEXP2_DisableInterrupt,
- .ClearInterrupt = AHB_PPCEXP2_ClearInterrupt,
- .InterruptState = AHB_PPCEXP2_InterruptState
-};
-#endif /* RTE_AHB_PPCEXP2 */
-
-#if (RTE_AHB_PPCEXP3)
-/* AHB PPCEXP3 Driver wrapper functions */
-static int32_t AHB_PPCEXP3_Initialize(void)
-{
- ppc_sse200_init(&AHB_PPCEXP3_DEV, AHB_PPC_EXP3);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPCEXP3_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t AHB_PPCEXP3_ConfigPeriph(uint8_t periph,
- ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&AHB_PPCEXP3_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t AHB_PPCEXP3_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&AHB_PPCEXP3_DEV, periph);
-}
-
-static uint32_t AHB_PPCEXP3_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&AHB_PPCEXP3_DEV, periph);
-}
-
-static int32_t AHB_PPCEXP3_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&AHB_PPCEXP3_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void AHB_PPCEXP3_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&AHB_PPCEXP3_DEV);
-}
-
-static void AHB_PPCEXP3_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&AHB_PPCEXP3_DEV);
-}
-
-static uint32_t AHB_PPCEXP3_InterruptState(void)
-{
- return ppc_sse200_irq_state(&AHB_PPCEXP3_DEV);
-}
-
-/* AHB PPCEXP3 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_AHB_PPCEXP3;
-ARM_DRIVER_PPC Driver_AHB_PPCEXP3 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = AHB_PPCEXP3_Initialize,
- .Uninitialize = AHB_PPCEXP3_Uninitialize,
- .ConfigPeriph = AHB_PPCEXP3_ConfigPeriph,
- .IsPeriphSecure = AHB_PPCEXP3_IsPeriphSecure,
- .IsPeriphPrivOnly = AHB_PPCEXP3_IsPeriphPrivOnly,
- .EnableInterrupt = AHB_PPCEXP3_EnableInterrupt,
- .DisableInterrupt = AHB_PPCEXP3_DisableInterrupt,
- .ClearInterrupt = AHB_PPCEXP3_ClearInterrupt,
- .InterruptState = AHB_PPCEXP3_InterruptState
-};
-#endif /* RTE_AHB_PPCEXP3 */
-
-#if (RTE_APB_PPC0)
-/* APB PPC0 Driver wrapper functions */
-static int32_t APB_PPC0_Initialize(void)
-{
- ppc_sse200_init(&APB_PPC0_DEV, APB_PPC0);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPC0_Uninitialize(void)
-{
- /* Nothing to be done*/
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPC0_ConfigPeriph(uint8_t periph, ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&APB_PPC0_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t APB_PPC0_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&APB_PPC0_DEV, periph);
-}
-
-static uint32_t APB_PPC0_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&APB_PPC0_DEV, periph);
-}
-
-static int32_t APB_PPC0_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&APB_PPC0_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void APB_PPC0_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&APB_PPC0_DEV);
-}
-
-static void APB_PPC0_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&APB_PPC0_DEV);
-}
-
-static uint32_t APB_PPC0_InterruptState(void)
-{
- return ppc_sse200_irq_state(&APB_PPC0_DEV);
-}
-
-/* APB PPC0 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_APB_PPC0;
-ARM_DRIVER_PPC Driver_APB_PPC0 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = APB_PPC0_Initialize,
- .Uninitialize = APB_PPC0_Uninitialize,
- .ConfigPeriph = APB_PPC0_ConfigPeriph,
- .IsPeriphSecure = APB_PPC0_IsPeriphSecure,
- .IsPeriphPrivOnly = APB_PPC0_IsPeriphPrivOnly,
- .EnableInterrupt = APB_PPC0_EnableInterrupt,
- .DisableInterrupt = APB_PPC0_DisableInterrupt,
- .ClearInterrupt = APB_PPC0_ClearInterrupt,
- .InterruptState = APB_PPC0_InterruptState
-};
-#endif /* RTE_APB_PPC0 */
-
-#if (RTE_APB_PPC1)
-/* APB PPC1 Driver wrapper functions */
-static int32_t APB_PPC1_Initialize(void)
-{
- ppc_sse200_init(&APB_PPC1_DEV, APB_PPC1);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPC1_Uninitialize(void)
-{
- /* Nothing to be done*/
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPC1_ConfigPeriph(uint8_t periph, ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&APB_PPC1_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t APB_PPC1_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&APB_PPC1_DEV, periph);
-}
-
-static uint32_t APB_PPC1_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&APB_PPC1_DEV, periph);
-}
-static int32_t APB_PPC1_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&APB_PPC1_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void APB_PPC1_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&APB_PPC1_DEV);
-}
-
-static void APB_PPC1_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&APB_PPC1_DEV);
-}
-
-static uint32_t APB_PPC1_InterruptState(void)
-{
- return ppc_sse200_irq_state(&APB_PPC1_DEV);
-}
-
-/* APB PPC1 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_APB_PPC1;
-ARM_DRIVER_PPC Driver_APB_PPC1 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = APB_PPC1_Initialize,
- .Uninitialize = APB_PPC1_Uninitialize,
- .ConfigPeriph = APB_PPC1_ConfigPeriph,
- .IsPeriphSecure = APB_PPC1_IsPeriphSecure,
- .IsPeriphPrivOnly = APB_PPC1_IsPeriphPrivOnly,
- .EnableInterrupt = APB_PPC1_EnableInterrupt,
- .DisableInterrupt = APB_PPC1_DisableInterrupt,
- .ClearInterrupt = APB_PPC1_ClearInterrupt,
- .InterruptState = APB_PPC1_InterruptState
-};
-#endif /* RTE_APB_PPC1 */
-
-#if (RTE_APB_PPCEXP0)
-/* APB PPCEXP0 Driver wrapper functions */
-static int32_t APB_PPCEXP0_Initialize(void)
-{
- ppc_sse200_init(&APB_PPCEXP0_DEV, APB_PPC_EXP0);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPCEXP0_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPCEXP0_ConfigPeriph(uint8_t periph,
- ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&APB_PPCEXP0_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t APB_PPCEXP0_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&APB_PPCEXP0_DEV, periph);
-}
-
-static uint32_t APB_PPCEXP0_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&APB_PPCEXP0_DEV, periph);
-}
-
-static int32_t APB_PPCEXP0_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&APB_PPCEXP0_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void APB_PPCEXP0_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&APB_PPCEXP0_DEV);
-}
-
-static void APB_PPCEXP0_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&APB_PPCEXP0_DEV);
-}
-
-static uint32_t APB_PPCEXP0_InterruptState(void)
-{
- return ppc_sse200_irq_state(&APB_PPCEXP0_DEV);
-}
-
-/* APB PPCEXP0 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_APB_PPCEXP0;
-ARM_DRIVER_PPC Driver_APB_PPCEXP0 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = APB_PPCEXP0_Initialize,
- .Uninitialize = APB_PPCEXP0_Uninitialize,
- .ConfigPeriph = APB_PPCEXP0_ConfigPeriph,
- .IsPeriphSecure = APB_PPCEXP0_IsPeriphSecure,
- .IsPeriphPrivOnly = APB_PPCEXP0_IsPeriphPrivOnly,
- .EnableInterrupt = APB_PPCEXP0_EnableInterrupt,
- .DisableInterrupt = APB_PPCEXP0_DisableInterrupt,
- .ClearInterrupt = APB_PPCEXP0_ClearInterrupt,
- .InterruptState = APB_PPCEXP0_InterruptState
-};
-#endif /* RTE_APB_PPCEXP0 */
-
-#if (RTE_APB_PPCEXP1)
-/* APB PPCEXP1 Driver wrapper functions */
-static int32_t APB_PPCEXP1_Initialize(void)
-{
- ppc_sse200_init(&APB_PPCEXP1_DEV, APB_PPC_EXP1);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPCEXP1_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPCEXP1_ConfigPeriph(uint8_t periph,
- ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&APB_PPCEXP1_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t APB_PPCEXP1_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&APB_PPCEXP1_DEV, periph);
-}
-
-static uint32_t APB_PPCEXP1_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&APB_PPCEXP1_DEV, periph);
-}
-
-static int32_t APB_PPCEXP1_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&APB_PPCEXP1_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void APB_PPCEXP1_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&APB_PPCEXP1_DEV);
-}
-
-static void APB_PPCEXP1_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&APB_PPCEXP1_DEV);
-}
-
-static uint32_t APB_PPCEXP1_InterruptState(void)
-{
- return ppc_sse200_irq_state(&APB_PPCEXP1_DEV);
-}
-
-/* APB PPCEXP1 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_APB_PPCEXP1;
-ARM_DRIVER_PPC Driver_APB_PPCEXP1 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = APB_PPCEXP1_Initialize,
- .Uninitialize = APB_PPCEXP1_Uninitialize,
- .ConfigPeriph = APB_PPCEXP1_ConfigPeriph,
- .IsPeriphSecure = APB_PPCEXP1_IsPeriphSecure,
- .IsPeriphPrivOnly = APB_PPCEXP1_IsPeriphPrivOnly,
- .EnableInterrupt = APB_PPCEXP1_EnableInterrupt,
- .DisableInterrupt = APB_PPCEXP1_DisableInterrupt,
- .ClearInterrupt = APB_PPCEXP1_ClearInterrupt,
- .InterruptState = APB_PPCEXP1_InterruptState
-};
-#endif /* RTE_APB_PPCEXP1 */
-
-#if (RTE_APB_PPCEXP2)
-/* APB PPCEXP2 Driver wrapper functions */
-static int32_t APB_PPCEXP2_Initialize(void)
-{
- ppc_sse200_init(&APB_PPCEXP2_DEV, APB_PPC_EXP2);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPCEXP2_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPCEXP2_ConfigPeriph(uint8_t periph,
- ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&APB_PPCEXP2_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t APB_PPCEXP2_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&APB_PPCEXP2_DEV, periph);
-}
-
-static uint32_t APB_PPCEXP2_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&APB_PPCEXP2_DEV, periph);
-}
-
-static int32_t APB_PPCEXP2_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&APB_PPCEXP2_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void APB_PPCEXP2_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&APB_PPCEXP2_DEV);
-}
-
-static void APB_PPCEXP2_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&APB_PPCEXP2_DEV);
-}
-
-static uint32_t APB_PPCEXP2_InterruptState(void)
-{
- return ppc_sse200_irq_state(&APB_PPCEXP2_DEV);
-}
-
-/* APB PPCEXP2 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_APB_PPCEXP2;
-ARM_DRIVER_PPC Driver_APB_PPCEXP2 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = APB_PPCEXP2_Initialize,
- .Uninitialize = APB_PPCEXP2_Uninitialize,
- .ConfigPeriph = APB_PPCEXP2_ConfigPeriph,
- .IsPeriphSecure = APB_PPCEXP2_IsPeriphSecure,
- .IsPeriphPrivOnly = APB_PPCEXP2_IsPeriphPrivOnly,
- .EnableInterrupt = APB_PPCEXP2_EnableInterrupt,
- .DisableInterrupt = APB_PPCEXP2_DisableInterrupt,
- .ClearInterrupt = APB_PPCEXP2_ClearInterrupt,
- .InterruptState = APB_PPCEXP2_InterruptState
-};
-#endif /* RTE_APB_PPCEXP2 */
-
-#if (RTE_APB_PPCEXP3)
-/* APB PPCEXP3 Driver wrapper functions */
-static int32_t APB_PPCEXP3_Initialize(void)
-{
- ppc_sse200_init(&APB_PPCEXP3_DEV, APB_PPC_EXP3);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPCEXP3_Uninitialize(void)
-{
- /* Nothing to be done */
- return ARM_DRIVER_OK;
-}
-
-static int32_t APB_PPCEXP3_ConfigPeriph(uint8_t periph, ARM_PPC_SecAttr sec_attr,
- ARM_PPC_PrivAttr priv_attr)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_config_peripheral(&APB_PPCEXP3_DEV, periph,
- (enum ppc_sse200_sec_attr_t)sec_attr,
- (enum ppc_sse200_priv_attr_t)priv_attr);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t APB_PPCEXP3_IsPeriphSecure(uint8_t periph)
-{
- return ppc_sse200_is_periph_secure(&APB_PPCEXP3_DEV, periph);
-}
-
-static uint32_t APB_PPCEXP3_IsPeriphPrivOnly(uint8_t periph)
-{
- return ppc_sse200_is_periph_priv_only(&APB_PPCEXP3_DEV, periph);
-}
-
-static int32_t APB_PPCEXP3_EnableInterrupt(void)
-{
- enum ppc_sse200_error_t ret;
-
- ret = ppc_sse200_irq_enable(&APB_PPCEXP3_DEV);
-
- if( ret != PPC_SSE200_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static void APB_PPCEXP3_DisableInterrupt(void)
-{
- ppc_sse200_irq_disable(&APB_PPCEXP3_DEV);
-}
-
-static void APB_PPCEXP3_ClearInterrupt(void)
-{
- ppc_sse200_clear_irq(&APB_PPCEXP3_DEV);
-}
-
-static uint32_t APB_PPCEXP3_InterruptState(void)
-{
- return ppc_sse200_irq_state(&APB_PPCEXP3_DEV);
-}
-
-/* APB PPCEXP3 Driver CMSIS access structure */
-extern ARM_DRIVER_PPC Driver_APB_PPCEXP3;
-ARM_DRIVER_PPC Driver_APB_PPCEXP3 = {
- .GetVersion = ARM_PPC_GetVersion,
- .Initialize = APB_PPCEXP3_Initialize,
- .Uninitialize = APB_PPCEXP3_Uninitialize,
- .ConfigPeriph = APB_PPCEXP3_ConfigPeriph,
- .IsPeriphSecure = APB_PPCEXP3_IsPeriphSecure,
- .IsPeriphPrivOnly = APB_PPCEXP3_IsPeriphPrivOnly,
- .EnableInterrupt = APB_PPCEXP3_EnableInterrupt,
- .DisableInterrupt = APB_PPCEXP3_DisableInterrupt,
- .ClearInterrupt = APB_PPCEXP3_ClearInterrupt,
- .InterruptState = APB_PPCEXP3_InterruptState
-};
-#endif /* RTE_APB_PPCEXP3 */
diff --git a/platform/ext/target/musca_a/CMSIS_Driver/Driver_QSPI_Flash.c b/platform/ext/target/musca_a/CMSIS_Driver/Driver_QSPI_Flash.c
deleted file mode 100644
index 3a1845c..0000000
--- a/platform/ext/target/musca_a/CMSIS_Driver/Driver_QSPI_Flash.c
+++ /dev/null
@@ -1,352 +0,0 @@
-/*
- * Copyright (c) 2013-2020 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include "Driver_Flash.h"
-
-#include <stdbool.h>
-#include <string.h>
-#include "cmsis_driver_config.h"
-#include "RTE_Device.h"
-#include "flash_layout.h"
-
-
-#ifndef ARG_UNUSED
-#define ARG_UNUSED(arg) ((void)arg)
-#endif
-
-/* Driver version */
-#define ARM_FLASH_DRV_VERSION ARM_DRIVER_VERSION_MAJOR_MINOR(1, 0)
-
-static const ARM_DRIVER_VERSION DriverVersion = {
- ARM_FLASH_API_VERSION, /* Defined in the CMSIS Flash Driver header file */
- ARM_FLASH_DRV_VERSION
-};
-
-/**
- * \brief Flash driver capability macro definitions \ref ARM_FLASH_CAPABILITIES
- */
-/* Flash Ready event generation capability values */
-#define EVENT_READY_NOT_AVAILABLE (0u)
-#define EVENT_READY_AVAILABLE (1u)
-/* Data access size values */
-#define DATA_WIDTH_8BIT (0u)
-#define DATA_WIDTH_16BIT (1u)
-#define DATA_WIDTH_32BIT (2u)
-/* Chip erase capability values */
-#define CHIP_ERASE_NOT_SUPPORTED (0u)
-#define CHIP_ERASE_SUPPORTED (1u)
-
-/* Driver Capabilities */
-static const ARM_FLASH_CAPABILITIES DriverCapabilities = {
- EVENT_READY_NOT_AVAILABLE,
- DATA_WIDTH_32BIT,
- CHIP_ERASE_SUPPORTED
-};
-
-/* Valid entries for data item width */
-static const uint32_t data_width_byte[] = {
- sizeof(uint8_t),
- sizeof(uint16_t),
- sizeof(uint32_t),
-};
-
-/**
- * \brief Flash status macro definitions \ref ARM_FLASH_STATUS
- */
-/* Busy status values of the Flash driver */
-#define DRIVER_STATUS_IDLE (0u)
-#define DRIVER_STATUS_BUSY (1u)
-/* Error status values of the Flash driver */
-#define DRIVER_STATUS_NO_ERROR (0u)
-#define DRIVER_STATUS_ERROR (1u)
-
-/**
- * \brief Arm Flash device structure.
- */
-struct arm_flash_dev_t {
- struct mt25ql_dev_t* dev; /*!< FLASH memory device structure */
- ARM_FLASH_INFO *data; /*!< FLASH memory device data */
-};
-
-/**
- * \brief Check if the Flash memory boundaries are not violated.
- * \param[in] flash_dev Flash device structure \ref arm_flash_dev_t
- * \param[in] offset Highest Flash memory address which would be accessed.
- * \return Returns true if Flash memory boundaries are not violated, false
- * otherwise.
- */
-static bool is_range_valid(struct arm_flash_dev_t *flash_dev,
- uint32_t offset)
-{
- uint32_t flash_limit = 0;
-
- /* Calculating the highest address of the Flash memory address range */
- flash_limit = FLASH_TOTAL_SIZE - 1;
-
- return (offset > flash_limit) ? (false) : (true) ;
-}
-
-/**
- * \brief Check if the parameter is aligned to program_unit.
- * \param[in] flash_dev Flash device structure \ref arm_flash_dev_t
- * \param[in] param Any number that can be checked against the
- * program_unit, e.g. Flash memory address or
- * data length in bytes.
- * \return Returns true if param is aligned to program_unit, false
- * otherwise.
- */
-static bool is_write_aligned(struct arm_flash_dev_t *flash_dev,
- uint32_t param)
-{
- return ((param % flash_dev->data->program_unit) != 0) ? (false) : (true);
-}
-
-#if (RTE_QSPI_FLASH0)
-static ARM_FLASH_INFO ARM_FLASH0_DEV_DATA = {
- .sector_info = NULL, /* Uniform sector layout */
- .sector_count = FLASH_TOTAL_SIZE / SUBSECTOR_4KB,
- .sector_size = SUBSECTOR_4KB,
- .page_size = FLASH_PAGE_SIZE,
- .program_unit = 1u, /* Minimum write size in bytes */
- .erased_value = 0xFF
-};
-
-static struct arm_flash_dev_t ARM_FLASH0_DEV = {
- .dev = &FLASH0_DEV,
- .data = &(ARM_FLASH0_DEV_DATA)
-};
-
-/* Flash Status */
-static ARM_FLASH_STATUS ARM_FLASH0_STATUS = {0, 0, 0};
-
-static ARM_DRIVER_VERSION ARM_Flash_GetVersion(void)
-{
- return DriverVersion;
-}
-
-static ARM_FLASH_CAPABILITIES ARM_Flash_GetCapabilities(void)
-{
- return DriverCapabilities;
-}
-
-static int32_t ARM_Flash_Initialize(ARM_Flash_SignalEvent_t cb_event)
-{
- enum mt25ql_error_t err = MT25QL_ERR_NONE;
-
- ARG_UNUSED(cb_event);
-
- qspi_ip6514e_enable(ARM_FLASH0_DEV.dev->controller);
-
- /* Configure QSPI Flash controller to operate in single SPI mode and
- * to use fast Flash commands */
- err = mt25ql_config_mode(ARM_FLASH0_DEV.dev, MT25QL_FUNC_STATE_FAST);
- if(err != MT25QL_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t ARM_Flash_Uninitialize(void)
-{
- enum mt25ql_error_t err = MT25QL_ERR_NONE;
-
- /* Restores the QSPI Flash controller and MT25QL to reset state */
- err = mt25ql_restore_reset_state(ARM_FLASH0_DEV.dev);
- if(err != MT25QL_ERR_NONE) {
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t ARM_Flash_PowerControl(ARM_POWER_STATE state)
-{
- switch(state) {
- case ARM_POWER_FULL:
- /* Nothing to be done */
- return ARM_DRIVER_OK;
- case ARM_POWER_OFF:
- case ARM_POWER_LOW:
- return ARM_DRIVER_ERROR_UNSUPPORTED;
- default:
- return ARM_DRIVER_ERROR_PARAMETER;
- }
-}
-
-static int32_t ARM_Flash_ReadData(uint32_t addr, void *data, uint32_t cnt)
-{
- /* Function includes a workaround for Musca-A QSPI flash when read data
- * could be corrupted if read size is not 4 byte aligned.
- */
- enum mt25ql_error_t err = MT25QL_ERR_NONE;
- bool is_valid = true;
- uint32_t extra_bytes = 0;
- uint32_t extra_word = 0;
-
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_NO_ERROR;
-
- /* Check Flash memory boundaries */
- is_valid = is_range_valid(&ARM_FLASH0_DEV, addr + cnt);
- if(is_valid != true) {
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_ERROR;
- return ARM_DRIVER_ERROR_PARAMETER;
- }
-
- ARM_FLASH0_STATUS.busy = DRIVER_STATUS_BUSY;
-
- if (cnt % data_width_byte[DriverCapabilities.data_width] != 0) {
- extra_bytes = cnt % data_width_byte[DriverCapabilities.data_width];
- cnt -= extra_bytes;
- }
-
- err = mt25ql_command_read(ARM_FLASH0_DEV.dev, addr, data, cnt);
-
- if (extra_bytes != 0) {
- err = mt25ql_command_read(ARM_FLASH0_DEV.dev, addr + cnt, &extra_word,
- data_width_byte[DriverCapabilities.data_width]);
- memcpy((char *) data + cnt, &extra_word, extra_bytes);
- }
-
- ARM_FLASH0_STATUS.busy = DRIVER_STATUS_IDLE;
-
- if(err != MT25QL_ERR_NONE) {
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_ERROR;
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t ARM_Flash_ProgramData(uint32_t addr,
- const void *data, uint32_t cnt)
-{
- enum mt25ql_error_t err = MT25QL_ERR_NONE;
-
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_NO_ERROR;
-
- /* Check Flash memory boundaries and alignment with minimum write size
- * (program_unit), data size also needs to be a multiple of program_unit.
- */
- if(!(is_range_valid(&ARM_FLASH0_DEV, addr + cnt) &&
- is_write_aligned(&ARM_FLASH0_DEV, addr) &&
- is_write_aligned(&ARM_FLASH0_DEV, cnt) )) {
-
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_ERROR;
- return ARM_DRIVER_ERROR_PARAMETER;
- }
-
- ARM_FLASH0_STATUS.busy = DRIVER_STATUS_BUSY;
-
- err = mt25ql_command_write(ARM_FLASH0_DEV.dev, addr, data, cnt);
-
- ARM_FLASH0_STATUS.busy = DRIVER_STATUS_IDLE;
-
- if(err != MT25QL_ERR_NONE) {
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_ERROR;
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t ARM_Flash_EraseSector(uint32_t addr)
-{
- enum mt25ql_error_t err = MT25QL_ERR_NONE;
-
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_NO_ERROR;
- ARM_FLASH0_STATUS.busy = DRIVER_STATUS_BUSY;
-
- /* The erase function checks whether the address is aligned with
- * the sector or subsector and checks the Flash memory boundaries.
- */
- err = mt25ql_erase(ARM_FLASH0_DEV.dev, addr,
- (enum mt25ql_erase_t) ARM_FLASH0_DEV.data->sector_size);
-
- ARM_FLASH0_STATUS.busy = DRIVER_STATUS_IDLE;
-
- if(err != MT25QL_ERR_NONE) {
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_ERROR;
-
- if((err == MT25QL_ERR_ADDR_NOT_ALIGNED) ||
- (err == MT25QL_ERR_ADDR_TOO_BIG) ||
- (err == MT25QL_ERR_WRONG_ARGUMENT) ) {
- return ARM_DRIVER_ERROR_PARAMETER;
- }
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t ARM_Flash_EraseChip(void)
-{
- enum mt25ql_error_t err = MT25QL_ERR_NONE;
-
- if(DriverCapabilities.erase_chip == 1) {
-
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_NO_ERROR;
- ARM_FLASH0_STATUS.busy = DRIVER_STATUS_BUSY;
-
- /* The erase function checks whether the address is aligned with
- * the sector or subsector and checks the Flash memory boundaries.
- */
- err = mt25ql_erase(ARM_FLASH0_DEV.dev, 0, MT25QL_ERASE_ALL_FLASH);
-
- ARM_FLASH0_STATUS.busy = DRIVER_STATUS_IDLE;
-
- if(err != MT25QL_ERR_NONE) {
- ARM_FLASH0_STATUS.error = DRIVER_STATUS_ERROR;
-
- if((err == MT25QL_ERR_ADDR_NOT_ALIGNED) ||
- (err == MT25QL_ERR_ADDR_TOO_BIG) ||
- (err == MT25QL_ERR_WRONG_ARGUMENT) ) {
- return ARM_DRIVER_ERROR_PARAMETER;
- }
- return ARM_DRIVER_ERROR;
- }
-
- return ARM_DRIVER_OK;
-
- } else {
- return ARM_DRIVER_ERROR_UNSUPPORTED;
- }
-}
-
-static ARM_FLASH_STATUS ARM_Flash_GetStatus(void)
-{
- return ARM_FLASH0_STATUS;
-}
-
-static ARM_FLASH_INFO * ARM_Flash_GetInfo(void)
-{
- return ARM_FLASH0_DEV.data;
-}
-
-ARM_DRIVER_FLASH Driver_FLASH0 = {
- ARM_Flash_GetVersion,
- ARM_Flash_GetCapabilities,
- ARM_Flash_Initialize,
- ARM_Flash_Uninitialize,
- ARM_Flash_PowerControl,
- ARM_Flash_ReadData,
- ARM_Flash_ProgramData,
- ARM_Flash_EraseSector,
- ARM_Flash_EraseChip,
- ARM_Flash_GetStatus,
- ARM_Flash_GetInfo
-};
-#endif /* RTE_QSPI_FLASH0 */
diff --git a/platform/ext/target/musca_a/CMSIS_Driver/Driver_USART.c b/platform/ext/target/musca_a/CMSIS_Driver/Driver_USART.c
deleted file mode 100644
index b66b445..0000000
--- a/platform/ext/target/musca_a/CMSIS_Driver/Driver_USART.c
+++ /dev/null
@@ -1,415 +0,0 @@
-/*
- * Copyright (c) 2013-2019 Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: Apache-2.0
- *
- * Licensed under the Apache License, Version 2.0 (the License); you may
- * not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an AS IS BASIS, WITHOUT
- * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include "Driver_USART.h"
-
-#include "cmsis_driver_config.h"
-#include "RTE_Device.h"
-
-#ifndef ARG_UNUSED
-#define ARG_UNUSED(arg) (void)arg
-#endif
-
-/* Driver version */
-#define ARM_USART_DRV_VERSION ARM_DRIVER_VERSION_MAJOR_MINOR(2, 2)
-
-/* Driver Version */
-static const ARM_DRIVER_VERSION DriverVersion = {
- ARM_USART_API_VERSION,
- ARM_USART_DRV_VERSION
-};
-
-/* Driver Capabilities */
-static const ARM_USART_CAPABILITIES DriverCapabilities = {
- 1, /* supports UART (Asynchronous) mode */
- 0, /* supports Synchronous Master mode */
- 0, /* supports Synchronous Slave mode */
- 0, /* supports UART Single-wire mode */
- 0, /* supports UART IrDA mode */
- 0, /* supports UART Smart Card mode */
- 0, /* Smart Card Clock generator available */
- 0, /* RTS Flow Control available */
- 0, /* CTS Flow Control available */
- 0, /* Transmit completed event: \ref ARM_USARTx_EVENT_TX_COMPLETE */
- 0, /* Signal receive character timeout event: \ref ARM_USARTx_EVENT_RX_TIMEOUT */
- 0, /* RTS Line: 0=not available, 1=available */
- 0, /* CTS Line: 0=not available, 1=available */
- 0, /* DTR Line: 0=not available, 1=available */
- 0, /* DSR Line: 0=not available, 1=available */
- 0, /* DCD Line: 0=not available, 1=available */
- 0, /* RI Line: 0=not available, 1=available */
- 0, /* Signal CTS change event: \ref ARM_USARTx_EVENT_CTS */
- 0, /* Signal DSR change event: \ref ARM_USARTx_EVENT_DSR */
- 0, /* Signal DCD change event: \ref ARM_USARTx_EVENT_DCD */
- 0, /* Signal RI change event: \ref ARM_USARTx_EVENT_RI */
- 0 /* Reserved */
-};
-
-static ARM_DRIVER_VERSION ARM_USART_GetVersion(void)
-{
- return DriverVersion;
-}
-
-static ARM_USART_CAPABILITIES ARM_USART_GetCapabilities(void)
-{
- return DriverCapabilities;
-}
-
-typedef struct {
- struct uart_pl011_dev_t* dev; /* UART device structure */
- uint32_t tx_nbr_bytes; /* Number of bytes transfered */
- uint32_t rx_nbr_bytes; /* Number of bytes recevied */
- ARM_USART_SignalEvent_t cb_event; /* Callback function for events */
-} UARTx_Resources;
-
-static int32_t ARM_USARTx_Initialize(UARTx_Resources* uart_dev)
-{
- /* Initializes generic UART driver */
- uart_pl011_init(uart_dev->dev, PeripheralClock);
-
- uart_pl011_enable(uart_dev->dev);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t ARM_USARTx_Uninitialize(UARTx_Resources* uart_dev)
-{
- /* Disables and uninitializes generic UART driver */
- uart_pl011_uninit(uart_dev->dev);
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t ARM_USARTx_PowerControl(UARTx_Resources* uart_dev,
- ARM_POWER_STATE state)
-{
- ARG_UNUSED(uart_dev);
-
- switch (state) {
- case ARM_POWER_OFF:
- case ARM_POWER_LOW:
- return ARM_DRIVER_ERROR_UNSUPPORTED;
- case ARM_POWER_FULL:
- /* Nothing to be done */
- return ARM_DRIVER_OK;
- default:
- return ARM_DRIVER_ERROR_PARAMETER;
- }
-}
-
-static int32_t ARM_USARTx_Send(UARTx_Resources* uart_dev, const void *data,
- uint32_t num)
-{
- const uint8_t* p_data = (const uint8_t*)data;
-
- if ((data == NULL) || (num == 0U)) {
- /* Invalid parameters */
- return ARM_DRIVER_ERROR_PARAMETER;
- }
-
- /* Resets previous TX counter */
- uart_dev->tx_nbr_bytes = 0;
-
- while(uart_dev->tx_nbr_bytes != num) {
- /* Waits until UART is ready to transmit */
- while(!uart_pl011_is_writable(uart_dev->dev)) {};
-
- /* As UART is ready to transmit at this point, the write function can
- * not return any transmit error */
- (void)uart_pl011_write(uart_dev->dev, *p_data);
-
- uart_dev->tx_nbr_bytes++;
- p_data++;
- }
-
- /* Waits until character is transmited */
- while (!uart_pl011_is_writable(uart_dev->dev)){};
-
- return ARM_DRIVER_OK;
-}
-
-static int32_t ARM_USARTx_Receive(UARTx_Resources* uart_dev,
- void *data, uint32_t num)
-{
- uint8_t* p_data = (uint8_t*)data;
-
- if ((data == NULL) || (num == 0U)) {
- // Invalid parameters
- return ARM_DRIVER_ERROR_PARAMETER;
- }
-
- /* Resets previous RX counter */
- uart_dev->rx_nbr_bytes = 0;
-
- while(uart_dev->rx_nbr_bytes != num) {
- /* Waits until one character is received */
- while (!uart_pl011_is_readable(uart_dev->dev)){};
-
- /* As UART has received one byte, the read can not
- * return any receive error at this point */
- (void)uart_pl011_read(uart_dev->dev, p_data);
-
- uart_dev->rx_nbr_bytes++;
- p_data++;
- }
-
- return ARM_DRIVER_OK;
-}
-
-static uint32_t ARM_USARTx_GetTxCount(UARTx_Resources* uart_dev)
-{
- return uart_dev->tx_nbr_bytes;
-}
-
-static uint32_t ARM_USARTx_GetRxCount(UARTx_Resources* uart_dev)
-{
- return uart_dev->rx_nbr_bytes;
-}
-
-static int32_t ARM_USARTx_Control(UARTx_Resources* uart_dev, uint32_t control,
- uint32_t arg)
-{
- switch (control & ARM_USART_CONTROL_Msk) {
- case ARM_USART_MODE_ASYNCHRONOUS:
- if(uart_pl011_set_baudrate(uart_dev->dev, arg) !=
- UART_PL011_ERR_NONE) {
- return ARM_USART_ERROR_BAUDRATE;
- }
- break;
- /* Unsupported command */
- default:
- return ARM_DRIVER_ERROR_UNSUPPORTED;
- }
-
- /* UART Data bits */
- if(control & ARM_USART_DATA_BITS_Msk) {
- /* Data bit is not configurable */
- return ARM_DRIVER_ERROR_UNSUPPORTED;
- }
-
- /* UART Parity */
- if(control & ARM_USART_PARITY_Msk) {
- /* Parity is not configurable */
- return ARM_USART_ERROR_PARITY;
- }
-
- /* USART Stop bits */
- if(control & ARM_USART_STOP_BITS_Msk) {
- /* Stop bit is not configurable */
- return ARM_USART_ERROR_STOP_BITS;
- }
-
- return ARM_DRIVER_OK;
-}
-
-#if (RTE_USART0)
-/* USART0 Driver wrapper functions */
-static UARTx_Resources USART0_DEV = {
- .dev = &UART0_DEV,
- .tx_nbr_bytes = 0,
- .rx_nbr_bytes = 0,
- .cb_event = NULL,
-};
-
-static int32_t ARM_USART0_Initialize(ARM_USART_SignalEvent_t cb_event)
-{
- USART0_DEV.cb_event = cb_event;
-
- musca_a1_scc_set_alt_func(&MUSCA_A1_SCC_DEV, GPIO_ALTFUNC_1, 1<<AHB_GPIO0_0);
- musca_a1_scc_set_alt_func(&MUSCA_A1_SCC_DEV, GPIO_ALTFUNC_1, 1<<AHB_GPIO0_1);
-
- return ARM_USARTx_Initialize(&USART0_DEV);
-}
-
-static int32_t ARM_USART0_Uninitialize(void)
-{
- return ARM_USARTx_Uninitialize(&USART0_DEV);
-}
-
-static int32_t ARM_USART0_PowerControl(ARM_POWER_STATE state)
-{
- return ARM_USARTx_PowerControl(&USART0_DEV, state);
-}
-
-static int32_t ARM_USART0_Send(const void *data, uint32_t num)
-{
- return ARM_USARTx_Send(&USART0_DEV, data, num);
-}
-
-static int32_t ARM_USART0_Receive(void *data, uint32_t num)
-{
- return ARM_USARTx_Receive(&USART0_DEV, data, num);
-}
-
-static int32_t ARM_USART0_Transfer(const void *data_out, void *data_in,
- uint32_t num)
-{
- ARG_UNUSED(data_out);
- ARG_UNUSED(data_in);
- ARG_UNUSED(num);
-
- return ARM_DRIVER_ERROR_UNSUPPORTED;
-}
-
-static uint32_t ARM_USART0_GetTxCount(void)
-{
- return ARM_USARTx_GetTxCount(&USART0_DEV);
-}
-
-static uint32_t ARM_USART0_GetRxCount(void)
-{
- return ARM_USARTx_GetRxCount(&USART0_DEV);
-}
-static int32_t ARM_USART0_Control(uint32_t control, uint32_t arg)
-{
- return ARM_USARTx_Control(&USART0_DEV, control, arg);
-}
-
-static ARM_USART_STATUS ARM_USART0_GetStatus(void)
-{
- ARM_USART_STATUS status = {0, 0, 0, 0, 0, 0, 0, 0};
- return status;
-}
-
-static int32_t ARM_USART0_SetModemControl(ARM_USART_MODEM_CONTROL control)
-{
- ARG_UNUSED(control);
- return ARM_DRIVER_ERROR_UNSUPPORTED;
-}
-
-static ARM_USART_MODEM_STATUS ARM_USART0_GetModemStatus(void)
-{
- ARM_USART_MODEM_STATUS modem_status = {0, 0, 0, 0, 0};
- return modem_status;
-}
-
-extern ARM_DRIVER_USART Driver_USART0;
-ARM_DRIVER_USART Driver_USART0 = {
- ARM_USART_GetVersion,
- ARM_USART_GetCapabilities,
- ARM_USART0_Initialize,
- ARM_USART0_Uninitialize,
- ARM_USART0_PowerControl,
- ARM_USART0_Send,
- ARM_USART0_Receive,
- ARM_USART0_Transfer,
- ARM_USART0_GetTxCount,
- ARM_USART0_GetRxCount,
- ARM_USART0_Control,
- ARM_USART0_GetStatus,
- ARM_USART0_SetModemControl,
- ARM_USART0_GetModemStatus
-};
-#endif /* RTE_USART0 */
-
-#if (RTE_USART1)
-/* USART1 Driver wrapper functions */
-static UARTx_Resources USART1_DEV = {
- .dev = &UART1_DEV,
- .tx_nbr_bytes = 0,
- .rx_nbr_bytes = 0,
- .cb_event = NULL,
-};
-
-static int32_t ARM_USART1_Initialize(ARM_USART_SignalEvent_t cb_event)
-{
- USART1_DEV.cb_event = cb_event;
-
- return ARM_USARTx_Initialize(&USART1_DEV);
-}
-
-static int32_t ARM_USART1_Uninitialize(void)
-{
- return ARM_USARTx_Uninitialize(&USART1_DEV);
-}
-
-static int32_t ARM_USART1_PowerControl(ARM_POWER_STATE state)
-{
- return ARM_USARTx_PowerControl(&USART1_DEV, state);
-}
-
-static int32_t ARM_USART1_Send(const void *data, uint32_t num)
-{
- return ARM_USARTx_Send(&USART1_DEV, data, num);
-}
-
-static int32_t ARM_USART1_Receive(void *data, uint32_t num)
-{
- return ARM_USARTx_Receive(&USART1_DEV, data, num);
-}
-
-static int32_t ARM_USART1_Transfer(const void *data_out, void *data_in,
- uint32_t num)
-{
- ARG_UNUSED(data_out);
- ARG_UNUSED(data_in);
- ARG_UNUSED(num);
-
- return ARM_DRIVER_ERROR_UNSUPPORTED;
-}
-
-static uint32_t ARM_USART1_GetTxCount(void)
-{
- return ARM_USARTx_GetTxCount(&USART1_DEV);
-}
-
-static uint32_t ARM_USART1_GetRxCount(void)
-{
- return ARM_USARTx_GetRxCount(&USART1_DEV);
-}
-static int32_t ARM_USART1_Control(uint32_t control, uint32_t arg)
-{
- return ARM_USARTx_Control(&USART1_DEV, control, arg);
-}
-
-static ARM_USART_STATUS ARM_USART1_GetStatus(void)
-{
- ARM_USART_STATUS status = {0, 0, 0, 0, 0, 0, 0, 0};
- return status;
-}
-
-static int32_t ARM_USART1_SetModemControl(ARM_USART_MODEM_CONTROL control)
-{
- ARG_UNUSED(control);
- return ARM_DRIVER_ERROR_UNSUPPORTED;
-}
-
-static ARM_USART_MODEM_STATUS ARM_USART1_GetModemStatus(void)
-{
- ARM_USART_MODEM_STATUS modem_status = {0, 0, 0, 0, 0};
- return modem_status;
-}
-
-extern ARM_DRIVER_USART Driver_USART1;
-ARM_DRIVER_USART Driver_USART1 = {
- ARM_USART_GetVersion,
- ARM_USART_GetCapabilities,
- ARM_USART1_Initialize,
- ARM_USART1_Uninitialize,
- ARM_USART1_PowerControl,
- ARM_USART1_Send,
- ARM_USART1_Receive,
- ARM_USART1_Transfer,
- ARM_USART1_GetTxCount,
- ARM_USART1_GetRxCount,
- ARM_USART1_Control,
- ARM_USART1_GetStatus,
- ARM_USART1_SetModemControl,
- ARM_USART1_GetModemStatus
-};
-#endif /* RTE_USART1 */
diff --git a/platform/ext/target/musca_a/CMakeLists.txt b/platform/ext/target/musca_a/CMakeLists.txt
deleted file mode 100644
index 5411842..0000000
--- a/platform/ext/target/musca_a/CMakeLists.txt
+++ /dev/null
@@ -1,165 +0,0 @@
-#-------------------------------------------------------------------------------
-# Copyright (c) 2020-2021, Arm Limited. All rights reserved.
-#
-# SPDX-License-Identifier: BSD-3-Clause
-#
-#-------------------------------------------------------------------------------
-
-cmake_policy(SET CMP0076 NEW)
-set(CMAKE_CURRENT_SOURCE_DIR ${CMAKE_CURRENT_LIST_DIR})
-
-message(DEPRECATION "${TFM_PLATFORM} has been marked for deprecation.")
-
-#========================= Platform region defs ===============================#
-
-target_include_directories(platform_region_defs
- INTERFACE
- partition
-)
-
-#========================= Platform common defs ===============================#
-
-# Specify the location of platform specific build dependencies.
-target_sources(tfm_s
- PRIVATE
- $<$<C_COMPILER_ID:ARMClang>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/armclang/startup_cmsdk_musca_s.s>
- $<$<C_COMPILER_ID:GNU>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/gcc/startup_cmsdk_musca_s.S>
- $<$<C_COMPILER_ID:IAR>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/iar/startup_cmsdk_musca_s.s>
-)
-
-target_add_scatter_file(tfm_s
- $<$<C_COMPILER_ID:ARMClang>:${CMAKE_SOURCE_DIR}/platform/ext/common/armclang/tfm_common_s.sct>
- $<$<C_COMPILER_ID:GNU>:${CMAKE_SOURCE_DIR}/platform/ext/common/gcc/tfm_common_s.ld>
- $<$<C_COMPILER_ID:IAR>:${CMAKE_SOURCE_DIR}/platform/ext/common/iar/tfm_common_s.icf>
-)
-
-if(NS)
- target_sources(tfm_ns
- PRIVATE
- $<$<C_COMPILER_ID:ARMClang>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/armclang/startup_cmsdk_musca_ns.s>
- $<$<C_COMPILER_ID:GNU>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/gcc/startup_cmsdk_musca_ns.S>
- $<$<C_COMPILER_ID:IAR>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/iar/startup_cmsdk_musca_ns.s>
- )
- target_add_scatter_file(tfm_ns
- $<$<C_COMPILER_ID:ARMClang>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/armclang/musca_ns.sct>
- $<$<C_COMPILER_ID:GNU>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/gcc/musca_ns.ld>
- $<$<C_COMPILER_ID:IAR>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/iar/musca_ns.icf>
- )
- target_link_libraries(CMSIS_5_tfm_ns
- INTERFACE
- CMSIS_5_RTX_V8MMN
- )
-endif()
-
-if(BL2)
- target_sources(bl2
- PRIVATE
- $<$<C_COMPILER_ID:ARMClang>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/armclang/startup_cmsdk_musca_bl2.s>
- $<$<C_COMPILER_ID:GNU>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/gcc/startup_cmsdk_musca_bl2.S>
- $<$<C_COMPILER_ID:IAR>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/iar/startup_cmsdk_musca_bl2.s>
- )
- target_add_scatter_file(bl2
- $<$<C_COMPILER_ID:ARMClang>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/armclang/musca_bl2.sct>
- $<$<C_COMPILER_ID:GNU>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/gcc/musca_bl2.ld>
- $<$<C_COMPILER_ID:IAR>:${CMAKE_CURRENT_SOURCE_DIR}/Device/Source/iar/musca_bl2.icf>
- )
-endif()
-
-#========================= Platform Secure ====================================#
-
-target_include_directories(platform_s
- PUBLIC
- .
- CMSIS_Driver
- CMSIS_Driver/Config
- Device/Config
- Device/Include
- Native_Driver
- partition
- services/include
- Libraries
-)
-
-target_sources(platform_s
- PRIVATE
- CMSIS_Driver/Driver_QSPI_Flash.c
- CMSIS_Driver/Driver_MPC.c
- CMSIS_Driver/Driver_PPC.c
- CMSIS_Driver/Driver_USART.c
- Device/Source/device_definition.c
- Device/Source/system_core_init.c
- Native_Driver/mpc_sie200_drv.c
- Native_Driver/mpu_armv8m_drv.c
- Native_Driver/ppc_sse200_drv.c
- Native_Driver/gpio_cmsdk_drv.c
- Native_Driver/qspi_ip6514e_drv.c
- Native_Driver/musca_a1_scc_drv.c
- spm_hal.c
- tfm_hal_isolation.c
- target_cfg.c
- Native_Driver/ppc_sse200_drv.c
- Native_Driver/uart_pl011_drv.c
- Native_Driver/timer_cmsdk_drv.c
- ${CMAKE_SOURCE_DIR}/platform/ext/common/tfm_hal_isolation_mpu_v8m.c
- $<$<BOOL:${TFM_PARTITION_PLATFORM}>:${CMAKE_CURRENT_SOURCE_DIR}/plat_test.c>
- $<$<BOOL:${TFM_PARTITION_PLATFORM}>:${CMAKE_CURRENT_SOURCE_DIR}/services/src/tfm_platform_system.c>
- Libraries/mt25ql_flash_lib.c
-)
-
-target_compile_options(platform_s
- PUBLIC
- ${COMPILER_CMSE_FLAG}
-)
-
-#========================= Platform Non-Secure ================================#
-
-target_sources(platform_ns
- PRIVATE
- Native_Driver/uart_pl011_drv.c
- Native_Driver/timer_cmsdk_drv.c
- CMSIS_Driver/Driver_USART.c
- Device/Source/system_core_init.c
- Device/Source/device_definition.c
- $<$<BOOL:${TFM_PARTITION_PLATFORM}>:${CMAKE_CURRENT_SOURCE_DIR}/plat_test.c>
- $<$<BOOL:${TFM_PARTITION_PLATFORM}>:${CMAKE_CURRENT_SOURCE_DIR}/services/src/tfm_platform_system.c>
-)
-
-target_include_directories(platform_ns
- PUBLIC
- .
- CMSIS_Driver/Config
- Device/Config
- Device/Include
- Native_Driver
- Libraries
- services/include
-)
-
-#========================= Platform BL2 =======================================#
-
-if(BL2)
- target_sources(platform_bl2
- PRIVATE
- CMSIS_Driver/Driver_QSPI_Flash.c
- boot_hal.c
- Device/Source/system_core_init.c
- Device/Source/device_definition.c
- Native_Driver/qspi_ip6514e_drv.c
- Native_Driver/uart_pl011_drv.c
- CMSIS_Driver/Driver_USART.c
- Native_Driver/musca_a1_scc_drv.c
- Libraries/mt25ql_flash_lib.c
- )
-
- target_include_directories(platform_bl2
- PUBLIC
- partition
- Device/Include
- Libraries
- PRIVATE
- .
- CMSIS_Driver/Config
- Device/Config
- Native_Driver
- )
-endif()
diff --git a/platform/ext/target/musca_a/Device/Config/device_cfg.h b/platform/ext/target/musca_a/Device/Config/device_cfg.h
deleted file mode 100644
index 9b32ca6..0000000
--- a/platform/ext/target/musca_a/Device/Config/device_cfg.h
+++ /dev/null
@@ -1,84 +0,0 @@
-/*
- * Copyright (c) 2017-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing software
- * distributed under the License is distributed on an "AS IS" BASIS
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#ifndef __ARM_LTD_DEVICE_CFG_H__
-#define __ARM_LTD_DEVICE_CFG_H__
-
-/**
- * \file device_cfg.h
- * \brief Configuration file native driver re-targeting
- *
- * \details This file can be used to add native driver specific macro
- * definitions to select which peripherals are available in the build.
- *
- * This is a default device configuration file with all peripherals enabled.
- */
-
-/* ARM SCC */
-#define MUSCA_A1_SCC_S
-#define MUSCA_A1_SCC_NS
-
-/* CMSDK GPIO */
-#define GPIO0_CMSDK_S
-
-/* ARM Memory Protection Controller (MPC) SIE 200 */
-#define MPC_ISRAM0_S
-#define MPC_ISRAM1_S
-#define MPC_ISRAM2_S
-#define MPC_ISRAM3_S
-#define MPC_CODE_SRAM_S
-#define MPC_CODE_SRAM_NS
-#define MPC_QSPI_S
-#define MPC_QSPI_NS
-
-/* ARM Peripheral Protection Controllers (PPC) */
-#define AHB_PPC0_S
-#define AHB_PPCEXP0_S
-#define AHB_PPCEXP1_S
-#define AHB_PPCEXP2_S
-#define AHB_PPCEXP3_S
-
-#define APB_PPC0_S
-#define APB_PPC1_S
-#define APB_PPCEXP0_S
-#define APB_PPCEXP1_S
-#define APB_PPCEXP2_S
-#define APB_PPCEXP3_S
-
-/*ARM UART Controller PL011*/
-#define UART0_PL011_S
-#define UART0_PL011_NS
-#define UART1_PL011_S
-#define UART1_PL011_NS
-
-/* CMSDK Timers */
-#define CMSDK_TIMER0_S
-#define CMSDK_TIMER0_NS
-#define CMSDK_TIMER1_S
-#define CMSDK_TIMER1_NS
-
-/* Cadence QSPI Flash Controller */
-#define QSPI_IP6514E_S
-#define QSPI_IP6514E_NS
-
-/* MT25QL Flash memory library */
-#define MT25QL_S
-#define MT25QL_NS
-
-/* Default UART baud rate */
-#define DEFAULT_UART_BAUDRATE 115200
-
-#endif /* __ARM_LTD_DEVICE_CFG_H__ */
diff --git a/platform/ext/target/musca_a/Device/Include/cmsis.h b/platform/ext/target/musca_a/Device/Include/cmsis.h
deleted file mode 100644
index db9fe01..0000000
--- a/platform/ext/target/musca_a/Device/Include/cmsis.h
+++ /dev/null
@@ -1,110 +0,0 @@
-/*
- * Copyright (c) 2017-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#ifndef __MUSCA_CMSIS_H__
-#define __MUSCA_CMSIS_H__
-
-/* Processor and Core Peripherals and configurations */
-
-/* ========================================================================= */
-/* ================ Processor and Core Peripheral Section ================ */
-/* ========================================================================= */
-
-/* ================ Start of section using anonymous unions ============== */
-#if defined (__CC_ARM)
- #pragma push
- #pragma anon_unions
-#elif defined (__ICCARM__)
- #pragma language=extended
-#elif defined(__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
- #pragma clang diagnostic push
- #pragma clang diagnostic ignored "-Wc11-extensions"
- #pragma clang diagnostic ignored "-Wreserved-id-macro"
-#elif defined (__GNUC__)
- /* anonymous unions are enabled by default */
-#elif defined (__TMS470__)
- /* anonymous unions are enabled by default */
-#elif defined (__TASKING__)
- #pragma warning 586
-#elif defined (__CSMC__)
- /* anonymous unions are enabled by default */
-#else
- #warning Not supported compiler type
-#endif
-
-
-/* -- Configuration of the Cortex-M33 Processor and Core Peripherals -- */
-#ifdef DUAL_CORE
-/* Both cores are used */
-#define __CM33_REV 0x0001U /* Core revision r0p1 */
-#define __SAUREGION_PRESENT 1U /* SAU regions present */
-#define __MPU_PRESENT 1U /* MPU present */
-#define __VTOR_PRESENT 1U /* VTOR present */
-#define __NVIC_PRIO_BITS 4U /* Number of Bits used for Priority
- * Levels */
-#define __Vendor_SysTickConfig 0U /* Set to 1 if different SysTick
- * Config is used */
-
-#if defined CORE0
-#define __FPU_PRESENT 0U /* no FPU present */
-#define __DSP_PRESENT 0U /* no DSP extension present */
-#elif defined CORE1
-#define __FPU_PRESENT 1U /* FPU present */
-#define __DSP_PRESENT 1U /* DSP extension present */
-#else
-#error "Either CORE0 or CORE1 must be defined"
-#endif /* CORE0/1 */
-
-#else /* DUAL_CORE */
-
-/* Single core is used */
-/* ----- Configuration of the Cortex-M33 Processor and Core Peripherals --- */
-#define __CM33_REV 0x0001U /* Core revision r0p1 */
-#define __SAUREGION_PRESENT 1U /* SAU regions present */
-#define __MPU_PRESENT 1U /* MPU present */
-#define __VTOR_PRESENT 1U /* VTOR present */
-#define __NVIC_PRIO_BITS 4U /* Number of Bits used for Priority
- * Levels */
-#define __Vendor_SysTickConfig 0U /* Set to 1 if different SysTick
- * Config is used */
-#define __FPU_PRESENT 0U /* no FPU present */
-#define __DSP_PRESENT 0U /* no DSP extension present */
-#endif /* DUAL_CORE */
-
-#include "system_core_init.h"
-#include "platform_irq.h"
-#include <core_cm33.h> /*!< Arm Cortex-M33 processor and core peripherals */
-
-/* ============== End of section using anonymous unions =================== */
-#if defined (__CC_ARM)
- #pragma pop
-#elif defined (__ICCARM__)
- /* leave anonymous unions enabled */
-#elif (__ARMCC_VERSION >= 6010050)
- #pragma clang diagnostic pop
-#elif defined (__GNUC__)
- /* anonymous unions are enabled by default */
-#elif defined (__TMS470__)
- /* anonymous unions are enabled by default */
-#elif defined (__TASKING__)
- #pragma warning restore
-#elif defined (__CSMC__)
- /* anonymous unions are enabled by default */
-#else
- #warning Not supported compiler type
-#endif
-
-#endif /*__MUSCA_CMSIS_H__ */
diff --git a/platform/ext/target/musca_a/Device/Include/device_definition.h b/platform/ext/target/musca_a/Device/Include/device_definition.h
deleted file mode 100644
index 4021e0a..0000000
--- a/platform/ext/target/musca_a/Device/Include/device_definition.h
+++ /dev/null
@@ -1,284 +0,0 @@
-/*
- * Copyright (c) 2017-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing software
- * distributed under the License is distributed on an "AS IS" BASIS
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file device_definition.h
- * \brief The structure definitions in this file are exported based
- * on the peripheral definitions from device_cfg.h.
- * This file is meant to be used as a helper for baremetal
- * applications and/or as an example of how to configure the generic
- * driver structures.
- */
-
-#ifndef __DEVICE_DEFINITION_H__
-#define __DEVICE_DEFINITION_H__
-
-#include "device_cfg.h"
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/* ======= Peripheral configuration structure declarations ======= */
-
-/* ARM SCC driver structures */
-#ifdef MUSCA_A1_SCC_S
-#include "musca_a1_scc_drv.h"
-extern struct musca_a1_scc_dev_t MUSCA_A1_SCC_DEV_S;
-#endif
-#ifdef MUSCA_A1_SCC_NS
-#include "musca_a1_scc_drv.h"
-extern struct musca_a1_scc_dev_t MUSCA_A1_SCC_DEV_NS;
-#endif
-
-/* ARM GPIO driver structures */
-#ifdef GPIO0_CMSDK_S
-#include "gpio_cmsdk_drv.h"
-extern struct gpio_cmsdk_dev_t GPIO0_CMSDK_DEV_S;
-#endif
-
-/* ARM MPC SIE 200 driver structures */
-#ifdef MPC_ISRAM0_S
-#include "mpc_sie200_drv.h"
-extern struct mpc_sie200_dev_t MPC_ISRAM0_DEV_S;
-#endif
-#ifdef MPC_ISRAM1_S
-#include "mpc_sie200_drv.h"
-extern struct mpc_sie200_dev_t MPC_ISRAM1_DEV_S;
-#endif
-#ifdef MPC_ISRAM2_S
-#include "mpc_sie200_drv.h"
-extern struct mpc_sie200_dev_t MPC_ISRAM2_DEV_S;
-#endif
-#ifdef MPC_ISRAM3_S
-#include "mpc_sie200_drv.h"
-extern struct mpc_sie200_dev_t MPC_ISRAM3_DEV_S;
-#endif
-#ifdef MPC_CODE_SRAM_S
-#include "mpc_sie200_drv.h"
-extern struct mpc_sie200_dev_t MPC_CODE_SRAM_DEV_S;
-#endif
-#ifdef MPC_CODE_SRAM_NS
-#include "mpc_sie200_drv.h"
-extern struct mpc_sie200_dev_t MPC_CODE_SRAM_DEV_NS;
-#endif
-#ifdef MPC_QSPI_S
-#include "mpc_sie200_drv.h"
-extern struct mpc_sie200_dev_t MPC_QSPI_DEV_S;
-#endif
-#ifdef MPC_QSPI_NS
-#include "mpc_sie200_drv.h"
-extern struct mpc_sie200_dev_t MPC_QSPI_DEV_NS;
-#endif
-
-/* ARM MHU driver structures */
-#ifdef ARM_MHU0_S
-#include "mhu_sse_200_drv.h"
-extern struct arm_mhu_sse_200_dev_t ARM_MHU0_DEV_S;
-#endif
-#ifdef ARM_MHU0_NS
-#include "mhu_sse_200_drv.h"
-extern struct arm_mhu_sse_200_dev_t ARM_MHU0_DEV_NS;
-#endif
-#ifdef ARM_MHU1_S
-#include "mhu_sse_200_drv.h"
-extern struct arm_mhu_sse_200_dev_t ARM_MHU1_DEV_S;
-#endif
-#ifdef ARM_MHU1_NS
-#include "mhu_sse_200_drv.h"
-extern struct arm_mhu_sse_200_dev_t ARM_MHU1_DEV_NS;
-#endif
-
-/* ARM UART PL011 driver structures */
-#ifdef UART0_PL011_S
-#include "uart_pl011_drv.h"
-extern struct uart_pl011_dev_t UART0_PL011_DEV_S;
-#endif
-#ifdef UART0_PL011_NS
-#include "uart_pl011_drv.h"
-extern struct uart_pl011_dev_t UART0_PL011_DEV_NS;
-#endif
-#ifdef UART1_PL011_S
-#include "uart_pl011_drv.h"
-extern struct uart_pl011_dev_t UART1_PL011_DEV_S;
-#endif
-#ifdef UART1_PL011_NS
-#include "uart_pl011_drv.h"
-extern struct uart_pl011_dev_t UART1_PL011_DEV_NS;
-#endif
-
-/* I2C IP6510 driver structures */
-#ifdef I2C0_IP6510_S
-#include "i2c_ip6510_drv.h"
-extern struct i2c_ip6510_dev_t I2C0_IP6510_DEV_S;
-#endif
-#ifdef I2C0_IP6510_NS
-#include "i2c_ip6510_drv.h"
-extern struct i2c_ip6510_dev_t I2C0_IP6510_DEV_NS;
-#endif
-#ifdef I2C1_IP6510_S
-#include "i2c_ip6510_drv.h"
-extern struct i2c_ip6510_dev_t I2C1_IP6510_DEV_S;
-#endif
-#ifdef I2C1_IP6510_NS
-#include "i2c_ip6510_drv.h"
-extern struct i2c_ip6510_dev_t I2C1_IP6510_DEV_NS;
-#endif
-
-/* CMSDK Dualtimer driver structures */
-#ifdef CMSDK_DUALTIMER_S
-#include "dualtimer_cmsdk_drv.h"
-extern struct dualtimer_cmsdk_dev_t CMSDK_DUALTIMER_DEV_S;
-#endif
-#ifdef CMSDK_DUALTIMER_NS
-#include "dualtimer_cmsdk_drv.h"
-extern struct dualtimer_cmsdk_dev_t CMSDK_DUALTIMER_DEV_NS;
-#endif
-
-/* CMSDK Timer driver structures */
-#ifdef CMSDK_TIMER0_S
-#include "timer_cmsdk_drv.h"
-extern struct timer_cmsdk_dev_t CMSDK_TIMER0_DEV_S;
-#endif
-#ifdef CMSDK_TIMER0_NS
-#include "timer_cmsdk_drv.h"
-extern struct timer_cmsdk_dev_t CMSDK_TIMER0_DEV_NS;
-#endif
-
-#ifdef CMSDK_TIMER1_S
-#include "timer_cmsdk_drv.h"
-extern struct timer_cmsdk_dev_t CMSDK_TIMER1_DEV_S;
-#endif
-#ifdef CMSDK_TIMER1_NS
-#include "timer_cmsdk_drv.h"
-extern struct timer_cmsdk_dev_t CMSDK_TIMER1_DEV_NS;
-#endif
-
-/* General-Purpose Timer driver structures */
-#ifdef GP_TIMER_S
-#include "timer_gp_drv.h"
-extern struct timer_gp_dev_t GP_TIMER_DEV_S;
-#endif
-#ifdef GP_TIMER_NS
-#include "timer_gp_drv.h"
-extern struct timer_gp_dev_t GP_TIMER_DEV_NS;
-#endif
-
-/* RTC PL031 */
-#ifdef RTC_PL031_S
-#include "rtc_pl031_drv.h"
-extern struct rtc_pl031_dev_t RTC_PL031_DEV_S;
-#endif
-
-#ifdef RTC_PL031_NS
-#include "rtc_pl031_drv.h"
-extern struct rtc_pl031_dev_t RTC_PL031_DEV_NS;
-#endif
-
-/* Cadence SPI IP6524 driver structures */
-#ifdef SPI0_IP6524_S
-#include "spi_ip6524_drv.h"
-extern struct spi_ip6524_dev_t SPI0_DEV_S;
-#endif
-#ifdef SPI0_IP6524_NS
-#include "spi_ip6524_drv.h"
-extern struct spi_ip6524_dev_t SPI0_DEV_NS;
-#endif
-
-/* QSPI Flash Controller driver structures */
-#ifdef QSPI_IP6514E_S
-#include "qspi_ip6514e_drv.h"
-extern struct qspi_ip6514e_dev_t QSPI_DEV_S;
-#endif
-
-#ifdef QSPI_IP6514E_NS
-#include "qspi_ip6514e_drv.h"
-extern struct qspi_ip6514e_dev_t QSPI_DEV_NS;
-#endif
-
-/* ARM PPC driver structures */
-#ifdef AHB_PPC0_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t AHB_PPC0_DEV_S;
-#endif
-
-#ifdef AHB_PPCEXP0_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t AHB_PPCEXP0_DEV_S;
-#endif
-
-#ifdef AHB_PPCEXP1_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t AHB_PPCEXP1_DEV_S;
-#endif
-
-#ifdef AHB_PPCEXP2_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t AHB_PPCEXP2_DEV_S;
-#endif
-
-#ifdef AHB_PPCEXP3_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t AHB_PPCEXP3_DEV_S;
-#endif
-
-#ifdef APB_PPC0_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t APB_PPC0_DEV_S;
-#endif
-
-#ifdef APB_PPC1_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t APB_PPC1_DEV_S;
-#endif
-
-#ifdef APB_PPCEXP0_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t APB_PPCEXP0_DEV_S;
-#endif
-
-#ifdef APB_PPCEXP1_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t APB_PPCEXP1_DEV_S;
-#endif
-
-#ifdef APB_PPCEXP2_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t APB_PPCEXP2_DEV_S;
-#endif
-
-#ifdef APB_PPCEXP3_S
-#include "ppc_sse200_drv.h"
-extern struct ppc_sse200_dev_t APB_PPCEXP3_DEV_S;
-#endif
-
-/* ======= External peripheral configuration structure declarations ======= */
-
-/* MT25QL Flash memory library structures */
-#if (defined(MT25QL_S) && defined(QSPI_IP6514E_S))
-#include "mt25ql_flash_lib.h"
-extern struct mt25ql_dev_t MT25QL_DEV_S;
-#endif
-#if (defined(MT25QL_NS) && defined(QSPI_IP6514E_NS))
-#include "mt25ql_flash_lib.h"
-extern struct mt25ql_dev_t MT25QL_DEV_NS;
-#endif
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __DEVICE_DEFINITION_H__ */
diff --git a/platform/ext/target/musca_a/Device/Include/platform_base_address.h b/platform/ext/target/musca_a/Device/Include/platform_base_address.h
deleted file mode 100644
index 85b17c1..0000000
--- a/platform/ext/target/musca_a/Device/Include/platform_base_address.h
+++ /dev/null
@@ -1,153 +0,0 @@
-/*
- * Copyright (c) 2017-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/*
- * This file is derivative of CMSIS V5.01 Device\_Template_Vendor\Vendor\Device\Include\Device.h
- */
-
-#ifndef __PLATFORM_BASE_ADDRESS_H__
-#define __PLATFORM_BASE_ADDRESS_H__
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-
-/* =========================================================================================================================== */
-/* ================ Device Specific Peripheral Address Map ================ */
-/* =========================================================================================================================== */
-
-
-/** @addtogroup Device_Peripheral_peripheralAddr
- * @{
- */
-
-/* Non-Secure Peripheral and SRAM base address */
-#define MUSCA_CODE_SRAM_NS_BASE (0x00000000UL) /*!< (Non-Secure Code SRAM ) Base Address */
-#define MUSCA_QSPI_FLASH_NS_BASE (0x00200000UL) /*!< (Non-Secure QSPI FLASH ) Base Address */
-#define MUSCA_OTP_NS_BASE (0x0E000000UL) /*!< (Non-Secure OTP ) Base Address */
-#define MUSCA_SRAM_NS_BASE (0x20000000UL) /*!< (Non-Secure Internal SRAM ) Base Address */
-#define MUSCA_BASE_ELEMENT_NS_BASE (0x40000000UL) /*!< (Non-Secure Base Peripherals ) Base Address */
-#define MUSCA_CMSDK_TIMER0_NS_BASE (0x40000000UL) /*!< (Non-Secure CMSDK Timer0 ) Base Address */
-#define MUSCA_CMSDK_TIMER1_NS_BASE (0x40001000UL) /*!< (Non-Secure CMSDK Timer1 ) Base Address */
-#define MUSCA_CMSDK_DUALTIMER_NS_BASE (0x40002000UL) /*!< (Non-Secure CMSDK Dual Timer ) Base Address */
-#define MUSCA_MHU0_NS_BASE (0x40003000UL) /*!< (Non-Secure MHU0 ) Base Address */
-#define MUSCA_MHU1_NS_BASE (0x40004000UL) /*!< (Non-Secure MHU1 ) Base Address */
-#define MUSCA_CPU_ELEMENT_NS_BASE (0x40010000UL) /*!< (Non-Secure CPU Peripherals ) Base Address */
-#define MUSCA_SYSTEM_INFO_NS_BASE (0x40020000UL) /*!< (Non-Secure System Info ) Base Address */
-#define MUSCA_CMSDK_S32KTIMER_NS_BASE (0x4002F000UL) /*!< (Non-Secure CMSDK S32K Timer ) Base Address */
-#define MUSCA_NSPCTRL_NS_BASE (0x40080000UL) /*!< (Non-Secure Privilege Ctrl Blk) Base Address */
-#define MUSCA_CMSDK_WATCHDOG_NS_BASE (0x40081000UL) /*!< (Non-Secure CMSDK Watchdog ) Base Address */
-#define MUSCA_UART0_NS_BASE (0x40101000UL) /*!< (Non-Secure UART0 ) Base Address */
-#define MUSCA_UART1_NS_BASE (0x40102000UL) /*!< (Non-Secure UART1 ) Base Address */
-#define MUSCA_SPI0_NS_BASE (0x40103000UL) /*!< (Non-Secure SPI0 ) Base Address */
-#define MUSCA_I2C0_NS_BASE (0x40104000UL) /*!< (Non-Secure I2C0 ) Base Address */
-#define MUSCA_I2C1_NS_BASE (0x40105000UL) /*!< (Non-Secure I2C1 ) Base Address */
-#define MUSCA_I2S_NS_BASE (0x40106000UL) /*!< (Non-Secure I2S ) Base Address */
-#define MUSCA_PWM0_NS_BASE (0x40107000UL) /*!< (Non-Secure PWM0 ) Base Address */
-#define MUSCA_RTC_NS_BASE (0x40108000UL) /*!< (Non-Secure RTC ) Base Address */
-#define MUSCA_PVT_NS_BASE (0x40109000UL) /*!< (Non-Secure PVT sensors ) Base Address */
-#define MUSCA_QSPI_REG_NS_BASE (0x4010A000UL) /*!< (Non-Secure QSPI registers ) Base Address */
-#define MUSCA_TIMER_NS_BASE (0x4010B000UL) /*!< (Non-Secure Timer ) Base Address */
-#define MUSCA_SCC_NS_BASE (0x4010C000UL) /*!< (Non-Secure SCC ) Base Address */
-#define MUSCA_PWM1_NS_BASE (0x4010E000UL) /*!< (Non-Secure PWM1 ) Base Address */
-#define MUSCA_PWM2_NS_BASE (0x4010F000UL) /*!< (Non-Secure PWM2 ) Base Address */
-#define MUSCA_GPIO_NS_BASE (0x40110000UL) /*!< (Non-Secure GPIO ) Base Address */
-#define MUSCA_QSPI_MPC_NS_BASE (0x40120000UL) /*!< (Non-Secure QSPI MPC ) Base Address */
-#define MUSCA_CODE_SRAM_MPC_NS_BASE (0x40130000UL) /*!< (Non-Secure Code SRAM MPC ) Base Address */
-#define MUSCA_DEFAULT_SLAVE_NS_BASE (0x60000000UL) /*!< (Non-Secure Unused AHB ) Base Address */
-/* Secure Peripheral and SRAM base address */
-#define MUSCA_CODE_SRAM_S_BASE (0x10000000UL) /*!< (Secure Code SRAM ) Base Address */
-#define MUSCA_QSPI_FLASH_S_BASE (0x10200000UL) /*!< (Secure QSPI FLASH ) Base Address */
-#define MUSCA_OTP_S_BASE (0x1E000000UL) /*!< (Secure OTP ) Base Address */
-#define MUSCA_SRAM_S_BASE (0x30000000UL) /*!< (Secure Internal SRAM ) Base Address */
-#define MUSCA_BASE_ELEMENT_S_BASE (0x50000000UL) /*!< (Secure Base Peripherals ) Base Address */
-#define MUSCA_MHU0_S_BASE (0x50003000UL) /*!< (Secure MHU0 ) Base Address */
-#define MUSCA_MHU1_S_BASE (0x50004000UL) /*!< (Secure MHU1 ) Base Address */
-#define MUSCA_CPU_ELEMENT_S_BASE (0x50010000UL) /*!< (Secure CPU Peripherals ) Base Address */
-#define MUSCA_SYSTEM_INFO_S_BASE (0x50020000UL) /*!< (Secure System Info ) Base Address */
-#define MUSCA_SYSTEM_CTRL_S_BASE (0x50021000UL) /*!< (Secure System Control ) Base Address */
-#define MUSCA_CMSDK_S32KTIMER_S_BASE (0x5002F000UL) /*!< (Secure CMSDK S32K Timer ) Base Address */
-#define MUSCA_CMSDK_TIMER0_S_BASE (0x50000000UL) /*!< (Secure CMSDK Timer0 ) Base Address */
-#define MUSCA_CMSDK_TIMER1_S_BASE (0x50001000UL) /*!< (Secure CMSDK Timer1 ) Base Address */
-#define MUSCA_CMSDK_DUALTIMER_S_BASE (0x50002000UL) /*!< (Secure CMSDK Dual Timer ) Base Address */
-#define MUSCA_SPCTRL_S_BASE (0x50080000UL) /*!< (Secure Privilege Ctrl Blk) Base Address */
-#define MUSCA_CMSDK_WATCHDOG_S_BASE (0x50081000UL) /*!< (Secure CMSDK Watchdog ) Base Address */
-#define MUSCA_MPC_SRAM0_S_BASE (0x50083000UL) /*!< (Secure MPC SRAM Bank 0 ) Base Address */
-#define MUSCA_MPC_SRAM1_S_BASE (0x50084000UL) /*!< (Secure MPC SRAM Bank 1 ) Base Address */
-#define MUSCA_MPC_SRAM2_S_BASE (0x50085000UL) /*!< (Secure MPC SRAM Bank 2 ) Base Address */
-#define MUSCA_MPC_SRAM3_S_BASE (0x50086000UL) /*!< (Secure MPC SRAM Bank 3 ) Base Address */
-#define MUSCA_UART0_S_BASE (0x50101000UL) /*!< (Secure UART0 ) Base Address */
-#define MUSCA_UART1_S_BASE (0x50102000UL) /*!< (Secure UART1 ) Base Address */
-#define MUSCA_SPI0_S_BASE (0x50103000UL) /*!< (Secure SPI0 ) Base Address */
-#define MUSCA_I2C0_S_BASE (0x50104000UL) /*!< (Secure I2C0 ) Base Address */
-#define MUSCA_I2C1_S_BASE (0x50105000UL) /*!< (Secure I2C1 ) Base Address */
-#define MUSCA_I2S_S_BASE (0x50106000UL) /*!< (Secure I2S ) Base Address */
-#define MUSCA_PWM0_S_BASE (0x50107000UL) /*!< (Secure PWM0 ) Base Address */
-#define MUSCA_RTC_S_BASE (0x50108000UL) /*!< (Secure RTC ) Base Address */
-#define MUSCA_PVT_S_BASE (0x50109000UL) /*!< (Secure PVT sensors ) Base Address */
-#define MUSCA_QSPI_REG_S_BASE (0x5010A000UL) /*!< (Secure QSPI registers ) Base Address */
-#define MUSCA_TIMER_S_BASE (0x5010B000UL) /*!< (Secure Timer ) Base Address */
-#define MUSCA_SCC_S_BASE (0x5010C000UL) /*!< (Secure SCC ) Base Address */
-#define MUSCA_PWM1_S_BASE (0x5010E000UL) /*!< (Secure PWM1 ) Base Address */
-#define MUSCA_PWM2_S_BASE (0x5010F000UL) /*!< (Secure PWM2 ) Base Address */
-#define MUSCA_GPIO_S_BASE (0x50110000UL) /*!< (Secure GPIO ) Base Address */
-#define MUSCA_QSPI_MPC_S_BASE (0x50120000UL) /*!< (Secure QSPI MPC ) Base Address */
-#define MUSCA_CODE_SRAM_MPC_S_BASE (0x50130000UL) /*!< (Secure Code SRAM MPC ) Base Address */
-#define MUSCA_DEFAULT_SLAVE_S_BASE (0x70000000UL) /*!< (Secure Unused AHB ) Base Address */
-
-/* SRAM MPC ranges and limits */
-/* Internal memory */
-#define MPC_ISRAM0_RANGE_BASE_NS 0x20000000
-#define MPC_ISRAM0_RANGE_LIMIT_NS 0x20007FFF
-#define MPC_ISRAM0_RANGE_BASE_S 0x30000000
-#define MPC_ISRAM0_RANGE_LIMIT_S 0x30007FFF
-
-#define MPC_ISRAM1_RANGE_BASE_NS 0x20008000
-#define MPC_ISRAM1_RANGE_LIMIT_NS 0x2000FFFF
-#define MPC_ISRAM1_RANGE_BASE_S 0x30008000
-#define MPC_ISRAM1_RANGE_LIMIT_S 0x3000FFFF
-
-#define MPC_ISRAM2_RANGE_BASE_NS 0x20010000
-#define MPC_ISRAM2_RANGE_LIMIT_NS 0x20017FFF
-#define MPC_ISRAM2_RANGE_BASE_S 0x30010000
-#define MPC_ISRAM2_RANGE_LIMIT_S 0x30017FFF
-
-#define MPC_ISRAM3_RANGE_BASE_NS 0x20018000
-#define MPC_ISRAM3_RANGE_LIMIT_NS 0x2001FFFF
-#define MPC_ISRAM3_RANGE_BASE_S 0x30018000
-#define MPC_ISRAM3_RANGE_LIMIT_S 0x3001FFFF
-
-/* Code SRAM memory */
-#define MPC_CODE_SRAM_RANGE_BASE_NS (0x00000000)
-#define MPC_CODE_SRAM_RANGE_LIMIT_NS (0x00200000)
-#define MPC_CODE_SRAM_RANGE_BASE_S (0x10000000)
-#define MPC_CODE_SRAM_RANGE_LIMIT_S (0x10200000)
-
-/* QSPI Flash memory */
-#define MPC_QSPI_RANGE_BASE_NS (0x00200000)
-#define MPC_QSPI_RANGE_LIMIT_NS (0x00240000)
-#define MPC_QSPI_RANGE_BASE_S (0x10200000)
-#define MPC_QSPI_RANGE_LIMIT_S (0x10240000)
-
-/** @} */ /* End of group Device_Peripheral_peripheralAddr */
-
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __PLATFORM_BASE_ADDRESS_H__ */
diff --git a/platform/ext/target/musca_a/Device/Include/platform_description.h b/platform/ext/target/musca_a/Device/Include/platform_description.h
deleted file mode 100644
index e5760c7..0000000
--- a/platform/ext/target/musca_a/Device/Include/platform_description.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/*
- * Copyright (c) 2018-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#ifndef __PLATFORM_DESCRIPTION_H__
-#define __PLATFORM_DESCRIPTION_H__
-
-#include "platform_base_address.h"
-#include "platform_pins.h"
-#include "platform_regs.h"
-#include "cmsis.h"
-
-#endif /* __PLATFORM_DESCRIPTION_H__ */
diff --git a/platform/ext/target/musca_a/Device/Include/platform_irq.h b/platform/ext/target/musca_a/Device/Include/platform_irq.h
deleted file mode 100644
index 886f037..0000000
--- a/platform/ext/target/musca_a/Device/Include/platform_irq.h
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * Copyright (c) 2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#ifndef __PLATFORM_IRQ_H__
-#define __PLATFORM_IRQ_H__
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/* ======================================================================= */
-/* ================== Interrupt Number Definition ===================== */
-/* ======================================================================= */
-
-
-typedef enum IRQn
-{
-/* =============== Core Specific Interrupt Numbers ====================== */
- NonMaskableInt_IRQn = -14, /* -14 Non Maskable Interrupt */
- HardFault_IRQn = -13, /* -13 HardFault Interrupt */
- MemoryManagement_IRQn = -12, /* -12 Memory Management Interrupt */
- BusFault_IRQn = -11, /* -11 Bus Fault Interrupt */
- UsageFault_IRQn = -10, /* -10 Usage Fault Interrupt */
- SecureFault_IRQn = -9, /* -9 Secure Fault Interrupt */
- SVCall_IRQn = -5, /* -5 SV Call Interrupt */
- DebugMonitor_IRQn = -4, /* -4 Debug Monitor Interrupt */
- PendSV_IRQn = -2, /* -2 Pend SV Interrupt */
- SysTick_IRQn = -1, /* -1 System Tick Interrupt */
-
-/* ============= Musca Specific SSE-200 Interrupt Numbers =============== */
- NS_WATCHDOG_RESET_IRQn = 0, /* Non-Secure Watchdog Reset Request
- * Interrupt */
- NS_WATCHDOG_IRQn = 1, /* Non-Secure Watchdog Interrupt */
- S32K_TIMER_IRQn = 2, /* S32K Timer Interrupt */
- TIMER0_IRQn = 3, /* CMSDK Timer 0 Interrupt */
- TIMER1_IRQn = 4, /* CMSDK Timer 1 Interrupt */
- DUALTIMER_IRQn = 5, /* CMSDK Dual Timer Interrupt */
- MHU0_IRQn = 6, /* Message Handling Unit 0 Interrupt */
- MHU1_IRQn = 7, /* Message Handling Unit 1 Interrupt */
- CRYPTOCELL_IRQn = 8, /* CryptoCell-312 Interrupt */
- S_MPC_COMBINED_IRQn = 9, /* Secure Combined MPC Interrupt */
- S_PPC_COMBINED_IRQn = 10, /* Secure Combined PPC Interrupt */
- S_MSC_COMBINED_IRQn = 11, /* Secure Combined MSC Interrupt */
- S_BRIDGE_ERR_IRQn = 12, /* Secure Bridge Error Combined
- * Interrupt */
- I_CACHE_INV_ERR_IRQn = 13, /* Instruction Cache Invalidation
- * Interrupt */
- /* Reserved = 14, Reserved */
- SYS_PPU_IRQn = 15, /* System PPU Interrupt */
- CPU0_PPU_IRQn = 16, /* CPU0 PPU Interrupt */
- CPU1_PPU_IRQn = 17, /* CPU1 PPU Interrupt */
- CPU0_DGB_PPU_IRQn = 18, /* CPU0 Debug PPU Interrupt */
- CPU1_DGB_PPU_IRQn = 19, /* CPU1 Debug PPU Interrupt */
- CRYPTOCELL_PPU_IRQn = 20, /* CryptoCell PPU Interrupt */
- /* Reserved = 21, Reserved */
- RAM0_PPU_IRQn = 22, /* RAM 0 PPU Interrupt */
- RAM1_PPU_IRQn = 23, /* RAM 1 PPU Interrupt */
- RAM2_PPU_IRQn = 24, /* RAM 2 PPU Interrupt */
- RAM3_PPU_IRQn = 25, /* RAM 3 PPU Interrupt */
- DEBUG_PPU_IRQn = 26, /* Debug PPU Interrupt */
- /* Reserved = 27, Reserved */
- CPU0_CTI_IRQn = 28, /* CPU0 CTI Interrupt */
- CPU1_CTI_IRQn = 29, /* CPU1 CTI Interrupt */
- /* Reserved = 30, Reserved */
- /* Reserved = 31, Reserved */
-/* ============ Musca Specific Expansion Interrupt Numbers ============== */
- /* None = 32, Not used. Tied to 0 */
- GpTimer_IRQn = 33, /* General Purpose Timer Interrupt */
- I2C0_IRQn = 34, /* I2C0 Interrupt */
- I2C1_IRQn = 35, /* I2C1 Interrupt */
- I2S_IRQn = 36, /* I2S Interrupt */
- SPI_IRQn = 37, /* SPI Interrupt */
- QSPI_IRQn = 38, /* QSPI Interrupt */
- UART0_Rx_IRQn = 39, /* UART0 receive FIFO interrupt */
- UART0_Tx_IRQn = 40, /* UART0 transmit FIFO interrupt */
- UART0_RxTimeout_IRQn = 41, /* UART0 receive timeout interrupt */
- UART0_ModemStatus_IRQn = 42, /* UART0 modem status interrupt */
- UART0_Error_IRQn = 43, /* UART0 error interrupt */
- UART0_IRQn = 44, /* UART0 interrupt */
- UART1_Rx_IRQn = 45, /* UART1 receive FIFO interrupt */
- UART1_Tx_IRQn = 46, /* UART1 transmit FIFO interrupt */
- UART1_RxTimeout_IRQn = 47, /* UART1 receive timeout interrupt */
- UART1_ModemStatus_IRQn = 48, /* UART1 modem status interrupt */
- UART1_Error_IRQn = 49, /* UART1 error interrupt */
- UART1_IRQn = 50, /* UART1 interrupt */
- GPIO_0_IRQn = 51, /* GPIO 0 interrupt */
- GPIO_1_IRQn = 52, /* GPIO 1 interrupt */
- GPIO_2_IRQn = 53, /* GPIO 2 interrupt */
- GPIO_3_IRQn = 54, /* GPIO 3 interrupt */
- GPIO_4_IRQn = 55, /* GPIO 4 interrupt */
- GPIO_5_IRQn = 56, /* GPIO 5 interrupt */
- GPIO_6_IRQn = 57, /* GPIO 6 interrupt */
- GPIO_7_IRQn = 58, /* GPIO 7 interrupt */
- GPIO_8_IRQn = 59, /* GPIO 8 interrupt */
- GPIO_9_IRQn = 60, /* GPIO 9 interrupt */
- GPIO_10_IRQn = 61, /* GPIO 10 interrupt */
- GPIO_11_IRQn = 62, /* GPIO 11 interrupt */
- GPIO_12_IRQn = 63, /* GPIO 12 interrupt */
- GPIO_13_IRQn = 64, /* GPIO 13 interrupt */
- GPIO_14_IRQn = 65, /* GPIO 14 interrupt */
- GPIO_15_IRQn = 66, /* GPIO 15 interrupt */
- Combined_IRQn = 67, /* Combined interrupt */
- PVT_IRQn = 68, /* PVT sensor interrupt */
- /* Reserved = 69, Reserved */
- PWM_0_IRQn = 70, /* PWM0 interrupt */
- RTC_IRQn = 71, /* RTC interrupt */
- GpTimer1_IRQn = 72, /* General Purpose Timer Alarm1
- * Interrupt */
- GpTimer0_IRQn = 73, /* General Purpose Timer Alarm0
- * Interrupt */
- PWM_1_IRQn = 74, /* PWM1 interrupt */
- PWM_2_IRQn = 75, /* PWM2 interrupt */
- IOMUX_IRQn = 76, /* IOMUX interrupt */
-} IRQn_Type;
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __PLATFORM_IRQ_H__ */
diff --git a/platform/ext/target/musca_a/Device/Include/platform_pins.h b/platform/ext/target/musca_a/Device/Include/platform_pins.h
deleted file mode 100644
index 5d1d927..0000000
--- a/platform/ext/target/musca_a/Device/Include/platform_pins.h
+++ /dev/null
@@ -1,45 +0,0 @@
-/*
- * Copyright (c) 2016-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing software
- * distributed under the License is distributed on an "AS IS" BASIS
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file platform_pins.h
- * \brief This file defines all the pins for this platform.
- */
-
-#ifndef __PLATFORM_PINS__
-#define __PLATFORM_PINS__
-
-/* AHB GPIO pin names */
-enum arm_gpio_pin_name_t {
- AHB_GPIO0_0 = 0U,
- AHB_GPIO0_1,
- AHB_GPIO0_2,
- AHB_GPIO0_3,
- AHB_GPIO0_4,
- AHB_GPIO0_5,
- AHB_GPIO0_6,
- AHB_GPIO0_7,
- AHB_GPIO0_8,
- AHB_GPIO0_9,
- AHB_GPIO0_10,
- AHB_GPIO0_11,
- AHB_GPIO0_12,
- AHB_GPIO0_13,
- AHB_GPIO0_14,
- AHB_GPIO0_15,
-};
-
-#endif /* __PLATFORM_PINS__ */
diff --git a/platform/ext/target/musca_a/Device/Include/platform_regs.h b/platform/ext/target/musca_a/Device/Include/platform_regs.h
deleted file mode 100644
index aef8d89..0000000
--- a/platform/ext/target/musca_a/Device/Include/platform_regs.h
+++ /dev/null
@@ -1,305 +0,0 @@
-/*
- * Copyright (c) 2016-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#ifndef __PLATFORM_REGS__
-#define __PLATFORM_REGS__
-
-#include <stdint.h>
-#include "platform_base_address.h"
-
-/* sysinfo memory mapped register access structure */
-struct sysinfo_t {
- volatile uint32_t sysversion; /* (R/ ) System version */
- volatile uint32_t sysconfig; /* (R/ ) System configuration */
- volatile uint32_t reserved0[1008];
- volatile uint32_t pidr4; /* (R/ ) Peripheral ID 4 */
- volatile uint32_t reserved1[3];
- volatile uint32_t pidr0; /* (R/ ) Peripheral ID 0 */
- volatile uint32_t pidr1; /* (R/ ) Peripheral ID 1 */
- volatile uint32_t pidr2; /* (R/ ) Peripheral ID 2 */
- volatile uint32_t pidr3; /* (R/ ) Peripheral ID 3 */
- volatile uint32_t cidr0; /* (R/ ) Component ID 0 */
- volatile uint32_t cidr1; /* (R/ ) Component ID 1 */
- volatile uint32_t cidr2; /* (R/ ) Component ID 2 */
- volatile uint32_t cidr3; /* (R/ ) Component ID 3 */
-};
-
-/* Secure System Control (SYSCTRL) Alias */
-#define CMSDK_SYSCTRL_BASE_S MUSCA_SYSTEM_CTRL_S_BASE
-
-/* sysctrl memory mapped register access structure */
-struct sysctrl_t {
- volatile uint32_t secdbgstat; /* (R/ ) Secure Debug Configuration
- * Status Register*/
- volatile uint32_t secdbgset; /* ( /W) Secure Debug Configuration
- * Set Register */
- volatile uint32_t secdbgclr; /* ( /W) Secure Debug Configuration
- * Clear Register */
- volatile uint32_t scsecctrl; /* (R/W) System Control Security
- * Control Register */
- volatile uint32_t fclk_div; /* (R/W) Fast Clock Divider
- * Configuration Register */
- volatile uint32_t sysclk_div; /* (R/W) System Clock Divider
- * Configuration Register */
- volatile uint32_t clockforce; /* (R/W) Clock Forces */
- volatile uint32_t reserved0[57];
- volatile uint32_t resetsyndrome; /* (R/W) Reset syndrome */
- volatile uint32_t resetmask; /* (R/W) Reset MASK */
- volatile uint32_t swreset; /* ( /W) Software Reset */
- volatile uint32_t gretreg; /* (R/W) General Purpose Retention
- * Register */
- volatile uint32_t initsvtor0; /* (R/W) Initial Secure Reset Vector
- * Register For CPU 0 */
- volatile uint32_t initsvtor1; /* (R/W) Initial Secure Reset
- * Vector Register For CPU 1*/
- volatile uint32_t cpuwait; /* (R/W) CPU Boot wait control
- * after reset */
- volatile uint32_t reserved1;
- volatile uint32_t wicctrl; /* (R/W) CPU WIC Request and
- * Acknowledgement */
- volatile uint32_t ewctrl; /* (R/W) External Wakeup Control */
- volatile uint32_t reserved2[54];
- volatile uint32_t pdcm_pd_sys_sense; /* (R/W) Power Control Dependency
- * Matrix PD_SYS
- * Power Domain Sensitivity.*/
- volatile uint32_t pdcm_pd_cpu0core_sense; /* (R/W) Power Control Dependency
- * Matrix PD_CPU0CORE
- * Power Domain Sensitivity.*/
- volatile uint32_t pdcm_pd_cpu1core_sense; /* (R/W) Power Control Dependency
- * Matrix PD_CPU1CORE
- * Power Domain Sensitivity.*/
- volatile uint32_t pdcm_pd_sram0_sense; /* (R/W) Power Control Dependency
- * Matrix PD_SRAM0 Power
- * Domain Sensitivity.*/
- volatile uint32_t pdcm_pd_sram1_sense; /* (R/W) Power Control Dependency
- * Matrix PD_SRAM1 Power
- * Domain Sensitivity.*/
- volatile uint32_t pdcm_pd_sram2_sense; /* (R/W) Power Control Dependency
- * Matrix PD_SRAM2 Power
- * Domain Sensitivity.*/
- volatile uint32_t pdcm_pd_sram3_sense; /* (R/W) Power Control Dependency
- * Matrix PD_SRAM3 Power
- * Domain Sensitivity.*/
- volatile uint32_t reserved3[5];
- volatile uint32_t pdcm_pd_cc_sense; /* (R/W) Power Control Dependency
- * Matrix PD_CC
- * Power Domain Sensitivity.*/
- volatile uint32_t pdcm_pd_exp0_out_sense; /* (R/W) Power Control Dependency
- * Matrix PD_EXP0 Sensitivity. */
- volatile uint32_t pdcm_pd_exp1_out_sense; /* (R/W) Power Control Dependency
- * Matrix PD_EXP1 Sensitivity. */
- volatile uint32_t pdcm_pd_exp2_out_sense; /* (R/W) Power Control Dependency
- * Matrix PD_EXP2 Sensitivity. */
- volatile uint32_t pdcm_pd_exp3_out_sense; /* (R/W) Power Control Dependency
- * Matrix PD_EXP3 Sensitivity. */
- volatile uint32_t reserved4[864];
- volatile uint32_t pidr4; /* (R/ ) Peripheral ID 4 */
- volatile uint32_t reserved5[3];
- volatile uint32_t pidr0; /* (R/ ) Peripheral ID 0 */
- volatile uint32_t pidr1; /* (R/ ) Peripheral ID 1 */
- volatile uint32_t pidr2; /* (R/ ) Peripheral ID 2 */
- volatile uint32_t pidr3; /* (R/ ) Peripheral ID 3 */
- volatile uint32_t cidr0; /* (R/ ) Component ID 0 */
- volatile uint32_t cidr1; /* (R/ ) Component ID 1 */
- volatile uint32_t cidr2; /* (R/ ) Component ID 2 */
- volatile uint32_t cidr3; /* (R/ ) Component ID 3 */
-};
-
-/* Secure Privilege Control */
-#define CMSDK_SPCTRL ((struct spctrl_def*)MUSCA_SPCTRL_S_BASE)
-
-/* SPCTRL memory mapped register access structure */
-struct spctrl_def {
- volatile uint32_t spcsecctrl; /* (R/W) Secure Configuration Control
- Register */
- volatile uint32_t buswait; /* (R/W) Bus Access wait control after reset.*/
- volatile uint32_t reserved[2];
- volatile uint32_t secrespcfg; /* (R/W) Security Violation Response
- * Configuration register.*/
- volatile uint32_t nsccfg; /* (R/W) Non Secure Callable Configuration
- * for IDAU. */
- volatile uint32_t reserved2;
- volatile uint32_t secmpcintstat; /* (R/W) Secure MPC Interrupt Status. */
- volatile uint32_t secppcintstat; /* (R/W) Secure PPC Interrupt Status. */
- volatile uint32_t secppcintclr; /* (R/W) Secure PPC Interrupt Clear. */
- volatile uint32_t secppcinten; /* (R/W) Secure PPC Interrupt Enable. */
- volatile uint32_t reserved3;
- volatile uint32_t secmscintstat; /* (R/W) Secure MSC Interrupt Status. */
- volatile uint32_t secmscintclr; /* (R/W) Secure MSC Interrupt Clear. */
- volatile uint32_t secmscinten; /* (R/W) Secure MSC Interrupt Enable. */
- volatile uint32_t reserved4;
- volatile uint32_t brgintstat; /* (R/W) Bridge Buffer Error Interrupt Status. */
- volatile uint32_t brgintclr; /* (R/W) Bridge Buffer Error Interrupt Clear. */
- volatile uint32_t brginten; /* (R/W) Bridge Buffer Error Interrupt Enable. */
- volatile uint32_t reserved5;
- volatile uint32_t ahbnsppc0; /* (R/W) Non-Secure Access AHB slave Peripheral
- * Protection Control #0 */
- volatile uint32_t reserved6[3];
- volatile uint32_t ahbnsppcexp0; /* (R/W) Expansion 0 Non_Secure Access AHB slave
- * Peripheral Protection Control */
- volatile uint32_t ahbnsppcexp1; /* (R/W) Expansion 1 Non_Secure Access AHB slave
- * Peripheral Protection Control */
- volatile uint32_t ahbnsppcexp2; /* (R/W) Expansion 2 Non_Secure Access AHB slave
- * Peripheral Protection Control */
- volatile uint32_t ahbnsppcexp3; /* (R/W) Expansion 3 Non_Secure Access AHB slave
- * Peripheral Protection Control */
- volatile uint32_t apbnsppc0; /* (R/W) Non-Secure Access APB slave Peripheral
- * Protection Control #0 */
- volatile uint32_t apbnsppc1; /* (R/W) Non-Secure Access APB slave Peripheral
- * Protection Control #1 */
- volatile uint32_t reserved7[2];
- volatile uint32_t apbnsppcexp0; /* (R/W) Expansion 0 Non_Secure Access APB slave
- * Peripheral Protection Control */
- volatile uint32_t apbnsppcexp1; /* (R/W) Expansion 1 Non_Secure Access APB slave
- * Peripheral Protection Control */
- volatile uint32_t apbnsppcexp2; /* (R/W) Expansion 2 Non_Secure Access APB slave
- * Peripheral Protection Control */
- volatile uint32_t apbnsppcexp3; /* (R/W) Expansion 3 Non_Secure Access APB slave
- * Peripheral Protection Control */
- volatile uint32_t ahbspppc0; /* (R/W) Secure Unprivileged Access AHB slave
- * Peripheral Protection Control #0. */
- volatile uint32_t reserved8[3];
- volatile uint32_t ahbspppcexp0; /* (R/W) Expansion 0 Secure Unprivileged Access
- * AHB slave Peripheral Protection Control. */
- volatile uint32_t ahbspppcexp1; /* (R/W) Expansion 1 Secure Unprivileged Access
- * AHB slave Peripheral Protection Control. */
- volatile uint32_t ahbspppcexp2; /* (R/W) Expansion 2 Secure Unprivileged Access
- * AHB slave Peripheral Protection Control. */
- volatile uint32_t ahbspppcexp3; /* (R/W) Expansion 3 Secure Unprivileged Access
- * AHB slave Peripheral Protection Control. */
- volatile uint32_t apbspppc0; /* (R/W) Secure Unprivileged Access APB slave
- * Peripheral Protection Control #0 */
- volatile uint32_t apbspppc1; /* (R/W) Secure Unprivileged Access APB slave
- * Peripheral Protection Control #1 */
- volatile uint32_t reserved9[2];
- volatile uint32_t apbspppcexp0; /* (R/W) Expansion 0 Secure Unprivileged Access
- * APB slave Peripheral Protection Control */
- volatile uint32_t apbspppcexp1; /* (R/W) Expansion 1 Secure Unprivileged Access
- * APB slave Peripheral Protection Control */
- volatile uint32_t apbspppcexp2; /* (R/W) Expansion 2 Secure Unprivileged Access
- * APB slave Peripheral Protection Control */
- volatile uint32_t apbspppcexp3; /* (R/W) Expansion 3 Secure Unprivileged Access
- * APB slave Peripheral Protection Control */
- volatile uint32_t nsmscexp; /* (R/W) Expansion MSC Non-Secure Configuration */
- volatile uint32_t reserved10[959];
- volatile uint32_t pid4; /* (R/W) Peripheral ID 4 */
- volatile uint32_t pid5; /* (R/W) Peripheral ID 5 */
- volatile uint32_t pid6; /* (R/W) Peripheral ID 6 */
- volatile uint32_t pid7; /* (R/W) Peripheral ID 7 */
- volatile uint32_t pid0; /* (R/W) Peripheral ID 0 */
- volatile uint32_t pid1; /* (R/W) Peripheral ID 1 */
- volatile uint32_t pid2; /* (R/W) Peripheral ID 2 */
- volatile uint32_t pid3; /* (R/W) Peripheral ID 3 */
- volatile uint32_t cid0; /* (R/W) Component ID 0 */
- volatile uint32_t cid1; /* (R/W) Component ID 1 */
- volatile uint32_t cid2; /* (R/W) Component ID 2 */
- volatile uint32_t cid3; /* (R/W) Component ID 3 */
-};
-
-/* Secure PPC interrupt position mask */
-#define CMSDK_APB_PPC0_INT_POS_MASK (1UL << 0)
-#define CMSDK_APB_PPC1_INT_POS_MASK (1UL << 1)
-#define CMSDK_APB_PPCEXP0_INT_POS_MASK (1UL << 4)
-#define CMSDK_APB_PPCEXP1_INT_POS_MASK (1UL << 5)
-#define CMSDK_APB_PPCEXP2_INT_POS_MASK (1UL << 6)
-#define CMSDK_APB_PPCEXP3_INT_POS_MASK (1UL << 7)
-#define CMSDK_AHB_PPCEXP0_INT_POS_MASK (1UL << 20)
-#define CMSDK_AHB_PPCEXP1_INT_POS_MASK (1UL << 21)
-#define CMSDK_AHB_PPCEXP2_INT_POS_MASK (1UL << 22)
-#define CMSDK_AHB_PPCEXP3_INT_POS_MASK (1UL << 23)
-
-/* Non-Secure Privilege Control */
-#define CMSDK_NSPCTRL ((struct nspctrl_def*)MUSCA_NSPCTRL_NS_BASE)
-
-/* NSPCTRL memory mapped register access structure */
-struct nspctrl_def {
- volatile uint32_t reserved[36];
- volatile uint32_t ahbnspppc0; /* (R/W) Non-Secure Unprivileged Access AHB slave
- * Peripheral Protection Control #0 */
- volatile uint32_t reserved3[3];
- volatile uint32_t ahbnspppcexp0; /* (R/W) Expansion 0 Non-Secure Unprivileged Access
- * AHB slave Peripheral Protection Control */
- volatile uint32_t ahbnspppcexp1; /* (R/W) Expansion 1 Non-Secure Unprivileged Access
- * AHB slave Peripheral Protection Control */
- volatile uint32_t ahbnspppcexp2; /* (R/W) Expansion 2 Non-Secure Unprivileged Access
- * AHB slave Peripheral Protection Control */
- volatile uint32_t ahbnspppcexp3; /* (R/W) Expansion 3 Non-Secure Unprivileged Access
- * AHB slave Peripheral Protection Control */
- volatile uint32_t apbnspppc0; /* (R/W) Non-Secure Unprivileged Access APB slave
- * Peripheral Protection Control #0 */
- volatile uint32_t apbnspppc1; /* (R/W) Non-Secure Unprivileged Access APB slave
- * Peripheral Protection Control #1 */
- volatile uint32_t reserved4[2];
- volatile uint32_t apbnspppcexp0; /* (R/W) Expansion 0 Non-Secure Unprivileged Access
- * APB slave Peripheral Protection Control */
- volatile uint32_t apbnspppcexp1; /* (R/W) Expansion 1 Non-Secure Unprivileged Access
- * APB slave Peripheral Protection Control */
- volatile uint32_t apbnspppcexp2; /* (R/W) Expansion 2 Non-Secure Unprivileged Access
- * APB slave Peripheral Protection Control */
- volatile uint32_t apbnspppcexp3; /* (R/W) Expansion 3 Non-Secure Unprivileged Access
- * APB slave Peripheral Protection Control */
- volatile uint32_t reserved5[960];
- volatile uint32_t pidr4; /* (R/W) Peripheral ID 3 */
- volatile uint32_t reserved7;
- volatile uint32_t reserved8;
- volatile uint32_t reserved9;
- volatile uint32_t pidr0; /* (R/W) Peripheral ID 0 */
- volatile uint32_t pidr1; /* (R/W) Peripheral ID 1 */
- volatile uint32_t pidr2; /* (R/W) Peripheral ID 2 */
- volatile uint32_t pidr3; /* (R/W) Peripheral ID 3 */
- volatile uint32_t cidr0; /* (R/W) Component ID 0 */
- volatile uint32_t cidr1; /* (R/W) Component ID 1 */
- volatile uint32_t cidr2; /* (R/W) Component ID 2 */
- volatile uint32_t cidr3; /* (R/W) Component ID 3 */
-};
-
-/* ARM APB PPC0 peripherals definition */
-#define CMSDK_TIMER0_APB_PPC_POS 0U
-#define CMSDK_TIMER1_APB_PPC_POS 1U
-#define CMSDK_DTIMER_APB_PPC_POS 2U
-#define CMSDK_MHU0_APB_PPC_POS 3U
-#define CMSDK_MHU1_APB_PPC_POS 4U
-/* The bits 31:5 are reserved */
-/* End ARM APB PPC0 peripherals definition */
-
-/* ARM APB PPC1 peripherals definition */
-#define CMSDK_S32K_TIMER_PPC_POS 0U
-/* The bits 31:1 are reserved */
-/* End ARM APB PPC1 peripherals definition */
-
-/* ARM AHB PPC0 peripherals definition */
-/* The bits 31:0 are reserved */
-/* End of ARM AHB PPC0 peripherals definition */
-
-/* ARM AHB PPCEXP0 peripherals definition */
-#define MUSCA_PERIPHS_AHB_PPC_POS 0U
-/* The bits 31:1 are reserved */
-/* End of ARM AHB PPCEXP0 peripherals definition */
-
-/* ARM AHB PPCEXP1 peripherals definition */
-/* The bits 31:0 are reserved */
-/* End of ARM AHB PPCEXP1 peripherals definition */
-
-/* ARM AHB PPCEXP2 peripherals definition */
-/* The bits 31:0 are reserved */
-/* End of ARM AHB PPCEXP2 peripherals definition */
-
-/* ARM AHB PPCEXP3 peripherals definition */
-/* The bits 31:0 are reserved */
-
-/* End of ARM AHB PPCEXP3 peripherals definition */
-
-#endif /* __PLATFORM_REGS__ */
diff --git a/platform/ext/target/musca_a/Device/Include/system_core_init.h b/platform/ext/target/musca_a/Device/Include/system_core_init.h
deleted file mode 100644
index 71005db..0000000
--- a/platform/ext/target/musca_a/Device/Include/system_core_init.h
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * Copyright (c) 2017-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- *
- * This file is derivative of CMSIS V5.01 \Device\ARM\ARMCM33\Include\system_ARMCM33.h
- * Git SHA: 8a1d9d6ee18b143ae5befefa14d89fb5b3f99c75
- *
- */
-
-#ifndef __SYSTEM_CORE_INIT_H__
-#define __SYSTEM_CORE_INIT_H__
-
-#include <stdint.h>
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-extern uint32_t SystemCoreClock; /*!< System Clock Frequency (Core Clock) */
-extern uint32_t PeripheralClock; /*!< Peripheral Clock Frequency */
-extern uint32_t RefClock; /*!< External Reference Clock Frequency */
-
-/**
- \brief Setup the microcontroller system.
-
- Initialize the System and update the SystemCoreClock variable.
- It should be called from Reset Handler within the first few steps.
- The minimal feature set should be initialised for successful exit
- from Reset Handler to main entry point.
- */
-extern void SystemInit (void);
-
-
-/**
- \brief Update SystemCoreClock variable.
-
- Updates the SystemCoreClock with current core Clock retrieved from cpu registers.
- */
-extern void SystemCoreClockUpdate (void);
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __SYSTEM_CORE_INIT_H__ */
diff --git a/platform/ext/target/musca_a/Device/Source/armclang/musca_bl2.sct b/platform/ext/target/musca_a/Device/Source/armclang/musca_bl2.sct
deleted file mode 100644
index 6180694..0000000
--- a/platform/ext/target/musca_a/Device/Source/armclang/musca_bl2.sct
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * Copyright (c) 2018-2020 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include "region_defs.h"
-
-LR_CODE BL2_CODE_START {
- ER_CODE BL2_CODE_START {
- startup_cmsdk_musca_bl2.o (RESET +First)
- startup_cmsdk_musca_bl2.o (+RO)
- system_core_init.o (+RO) ; SystemInit
- *(InRoot$$Sections) ; ARM library sections
- }
-
- ER_CODE_SRAM BL2_CODE_SRAM_BASE {
- * (+RO) ; app code that gets copied from Flash to SRAM
- }
-
- /* Base address of bootloader data area */
- BL2_DATA_START S_DATA_START {
- }
-
- TFM_SHARED_DATA +0 ALIGN 32 EMPTY BOOT_TFM_SHARED_DATA_SIZE {
- }
-
- ER_DATA +0 {
- * (+ZI +RW)
- }
-
- /* MSP */
- ARM_LIB_STACK +0 ALIGN 32 EMPTY BL2_MSP_STACK_SIZE {
- }
-
- ARM_LIB_HEAP +0 ALIGN 8 EMPTY BL2_HEAP_SIZE {
- }
-
- /* This empty, zero long execution region is here to mark the limit address
- * of the last execution region that is allocated in SRAM.
- */
- SRAM_WATERMARK +0 EMPTY 0x0 {
- }
-
- /* Make sure that the sections allocated in the SRAM does not exceed the
- * size of the SRAM available.
- */
- ScatterAssert(ImageLimit(SRAM_WATERMARK) <= BL2_DATA_START + BL2_DATA_SIZE)
-}
diff --git a/platform/ext/target/musca_a/Device/Source/armclang/musca_ns.sct b/platform/ext/target/musca_a/Device/Source/armclang/musca_ns.sct
deleted file mode 100644
index ea7d5e1..0000000
--- a/platform/ext/target/musca_a/Device/Source/armclang/musca_ns.sct
+++ /dev/null
@@ -1,50 +0,0 @@
-/*
- * Copyright (c) 2018-2020 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include "region_defs.h"
-
-LR_CODE NS_CODE_START {
- ER_CODE NS_CODE_START NS_CODE_SIZE {
- *.o (RESET +First)
- * (+RO)
- }
-
- ER_DATA NS_DATA_START {
- * (+ZI +RW)
- }
-
- /* MSP */
- ARM_LIB_STACK_MSP +0 ALIGN 32 EMPTY NS_MSP_STACK_SIZE {
- }
-
- /* PSP */
- ARM_LIB_STACK +0 ALIGN 32 EMPTY NS_PSP_STACK_SIZE {
- }
-
- ARM_LIB_HEAP +0 ALIGN 8 EMPTY NS_HEAP_SIZE {
- }
-
- /* This empty, zero long execution region is here to mark the limit address
- * of the last execution region that is allocated in SRAM.
- */
- SRAM_WATERMARK +0 EMPTY 0x0 {
- }
-
- /* Make sure that the sections allocated in the SRAM does not exceed the
- * size of the SRAM available.
- */
- ScatterAssert(ImageLimit(SRAM_WATERMARK) <= NS_DATA_START + NS_DATA_SIZE)
-}
diff --git a/platform/ext/target/musca_a/Device/Source/armclang/startup_cmsdk_musca_bl2.s b/platform/ext/target/musca_a/Device/Source/armclang/startup_cmsdk_musca_bl2.s
deleted file mode 100644
index 3ed69d6..0000000
--- a/platform/ext/target/musca_a/Device/Source/armclang/startup_cmsdk_musca_bl2.s
+++ /dev/null
@@ -1,248 +0,0 @@
-;/*
-; * Copyright (c) 2017-2018 ARM Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; */
-;
-; This file is derivative of CMSIS V5.01 startup_ARMv8MML.s
-; Git SHA: 8a1d9d6ee18b143ae5befefa14d89fb5b3f99c75
-
-;/*
-;//-------- <<< Use Configuration Wizard in Context Menu >>> ------------------
-;*/
-
-
-; <h> Stack Configuration
-; <o> Stack Size (in Bytes) <0x0-0xFFFFFFFF:8>
-; </h>
-
- IMPORT |Image$$ARM_LIB_STACK$$ZI$$Limit|
-
-; Vector Table Mapped to Address 0 at Reset
-
- AREA RESET, DATA, READONLY
- EXPORT __Vectors
- EXPORT __Vectors_End
- EXPORT __Vectors_Size
-
-__Vectors ;Core Interrupts
- DCD |Image$$ARM_LIB_STACK$$ZI$$Limit| ; Top of Stack
- DCD Reset_Handler ; Reset Handler
- DCD NMI_Handler ; NMI Handler
- DCD HardFault_Handler ; Hard Fault Handler
- DCD MemManage_Handler ; MPU Fault Handler
- DCD BusFault_Handler ; Bus Fault Handler
- DCD UsageFault_Handler ; Usage Fault Handler
- DCD SecureFault_Handler ; Secure Fault Handler
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD SVC_Handler ; SVCall Handler
- DCD DebugMon_Handler ; Debug Monitor Handler
- DCD 0 ; Reserved
- DCD PendSV_Handler ; PendSV Handler
- DCD SysTick_Handler ; SysTick Handler
- ;SSE-200 Interrupts
- DCD NS_WATCHDOG_RESET_IRQHandler ; 0: Non-Secure Watchdog Reset Request Interrupt
- DCD NS_WATCHDOG_IRQHandler ; 1: Non-Secure Watchdog Interrupt
- DCD S32K_TIMER_IRQHandler ; 2: S32K Timer Interrupt
- DCD TIMER0_IRQHandler ; 3: CMSDK Timer 0 Interrupt
- DCD TIMER1_IRQHandler ; 4: CMSDK Timer 1 Interrupt
- DCD DUALTIMER_IRQHandler ; 5: CMSDK Dual Timer Interrupt
- DCD MHU0_IRQHandler ; 6: Message Handling Unit 0 Interrupt
- DCD MHU1_IRQHandler ; 7: Message Handling Unit 1 Interrupt
- DCD CRYPTOCELL_IRQHandler ; 8: CryptoCell-312 Interrupt
- DCD MPC_Handler ; 9: Secure Combined MPC Interrupt
- DCD PPC_Handler ; 10: Secure Combined PPC Interrupt
- DCD S_MSC_COMBINED_IRQHandler ; 11: Secure Combined MSC Interrupt
- DCD S_BRIDGE_ERR_IRQHandler ; 12: Secure Bridge Error Combined Interrupt
- DCD I_CACHE_INV_ERR_IRQHandler ; 13: Intsruction Cache Invalidation Interrupt
- DCD 0 ; 14: Reserved
- DCD SYS_PPU_IRQHandler ; 15: System PPU Interrupt
- DCD CPU0_PPU_IRQHandler ; 16: CPU0 PPU Interrupt
- DCD CPU1_PPU_IRQHandler ; 17: CPU1 PPU Interrupt
- DCD CPU0_DGB_PPU_IRQHandler ; 18: CPU0 Debug PPU Interrupt
- DCD CPU1_DGB_PPU_IRQHandler ; 19: CPU1 Debug PPU Interrupt
- DCD CRYPTOCELL_PPU_IRQHandler ; 20: CryptoCell PPU Interrupt
- DCD 0 ; 21: Reserved
- DCD RAM0_PPU_IRQHandler ; 22: RAM 0 PPU Interrupt
- DCD RAM1_PPU_IRQHandler ; 23: RAM 1 PPU Interrupt
- DCD RAM2_PPU_IRQHandler ; 24: RAM 2 PPU Interrupt
- DCD RAM3_PPU_IRQHandler ; 25: RAM 3 PPU Interrupt
- DCD DEBUG_PPU_IRQHandler ; 26: Debug PPU Interrupt
- DCD 0 ; 27: Reserved
- DCD CPU0_CTI_IRQHandler ; 28: CPU0 CTI Interrupt
- DCD CPU1_CTI_IRQHandler ; 29: CPU1 CTI Interrupt
- DCD 0 ; 30: Reserved
- DCD 0 ; 31: Reserved
- ;Expansion Interrupts
- DCD 0 ; 32: Reserved
- DCD GpTimer_IRQHandler ; 33: General Purpose Timer
- DCD I2C0_IRQHandler ; 34: I2C0
- DCD I2C1_IRQHandler ; 35: I2C1
- DCD I2S_IRQHandler ; 36: I2S
- DCD SPI_IRQHandler ; 37: SPI
- DCD QSPI_IRQHandler ; 38: QSPI
- DCD UARTRX0_Handler ; 39: UART0 receive FIFO interrupt
- DCD UARTTX0_Handler ; 40: UART0 transmit FIFO interrupt
- DCD UART0_RxTimeout_IRQHandler ; 41: UART0 receive timeout interrupt
- DCD UART0_ModemStatus_IRQHandler ; 42: UART0 modem status interrupt
- DCD UART0_Error_IRQHandler ; 43: UART0 error interrupt
- DCD UART0_IRQHandler ; 44: UART0 interrupt
- DCD UARTRX1_Handler ; 45: UART0 receive FIFO interrupt
- DCD UARTTX1_Handler ; 46: UART0 transmit FIFO interrupt
- DCD UART1_RxTimeout_IRQHandler ; 47: UART0 receive timeout interrupt
- DCD UART1_ModemStatus_IRQHandler ; 48: UART0 modem status interrupt
- DCD UART1_Error_IRQHandler ; 49: UART0 error interrupt
- DCD UART1_IRQHandler ; 50: UART0 interrupt
- DCD GPIO_0_IRQHandler ; 51: GPIO 0 interrupt
- DCD GPIO_1_IRQHandler ; 52: GPIO 1 interrupt
- DCD GPIO_2_IRQHandler ; 53: GPIO 2 interrupt
- DCD GPIO_3_IRQHandler ; 54: GPIO 3 interrupt
- DCD GPIO_4_IRQHandler ; 55: GPIO 4 interrupt
- DCD GPIO_5_IRQHandler ; 56: GPIO 5 interrupt
- DCD GPIO_6_IRQHandler ; 57: GPIO 6 interrupt
- DCD GPIO_7_IRQHandler ; 58: GPIO 7 interrupt
- DCD GPIO_8_IRQHandler ; 59: GPIO 8 interrupt
- DCD GPIO_9_IRQHandler ; 60: GPIO 9 interrupt
- DCD GPIO_10_IRQHandler ; 61: GPIO 10 interrupt
- DCD GPIO_11_IRQHandler ; 62: GPIO 11 interrupt
- DCD GPIO_12_IRQHandler ; 63: GPIO 12 interrupt
- DCD GPIO_13_IRQHandler ; 64: GPIO 13 interrupt
- DCD GPIO_14_IRQHandler ; 65: GPIO 14 interrupt
- DCD GPIO_15_IRQHandler ; 66: GPIO 15 interrupt
- DCD Combined_IRQHandler ; 67: Combined interrupt
- DCD PVT_IRQHandler ; 68: PVT sensor interrupt
- DCD 0 ; 69: Reserved
- DCD PWM_0_IRQHandler ; 70: PWM0 interrupt
- DCD RTC_IRQHandler ; 71: RTC interrupt
- DCD GpTimer0_IRQHandler ; 72: General Purpose Timer0
- DCD GpTimer1_IRQHandler ; 73: General Purpose Timer1
- DCD PWM_1_IRQHandler ; 74: PWM1 interrupt
- DCD PWM_2_IRQHandler ; 75: PWM2 interrupt
- DCD IOMUX_IRQHandler ; 76: IOMUX interrupt
-
-__Vectors_End
-
-__Vectors_Size EQU __Vectors_End - __Vectors
-
-; Reset Handler
- AREA |.text|, CODE, READONLY
-Reset_Handler PROC
- EXPORT Reset_Handler [WEAK]
- IMPORT SystemInit
- IMPORT __main
- LDR R0, =SystemInit
- BLX R0
- LDR R0, =__main
- BX R0
- ENDP
-End_Of_Main
- B .
-
-
-; Dummy Exception Handlers (infinite loops which can be modified)
- MACRO
- Default_Handler $handler_name
-$handler_name PROC
- EXPORT $handler_name [WEAK]
- B .
- ENDP
- MEND
-
- Default_Handler NMI_Handler
- Default_Handler HardFault_Handler
- Default_Handler MemManage_Handler
- Default_Handler BusFault_Handler
- Default_Handler UsageFault_Handler
- Default_Handler SecureFault_Handler
- Default_Handler SVC_Handler
- Default_Handler DebugMon_Handler
- Default_Handler PendSV_Handler
- Default_Handler SysTick_Handler
-
- Default_Handler NS_WATCHDOG_RESET_IRQHandler
- Default_Handler NS_WATCHDOG_IRQHandler
- Default_Handler S32K_TIMER_IRQHandler
- Default_Handler TIMER0_IRQHandler
- Default_Handler TIMER1_IRQHandler
- Default_Handler DUALTIMER_IRQHandler
- Default_Handler MHU0_IRQHandler
- Default_Handler MHU1_IRQHandler
- Default_Handler CRYPTOCELL_IRQHandler
- Default_Handler MPC_Handler
- Default_Handler PPC_Handler
- Default_Handler S_MSC_COMBINED_IRQHandler
- Default_Handler S_BRIDGE_ERR_IRQHandler
- Default_Handler I_CACHE_INV_ERR_IRQHandler
- Default_Handler SYS_PPU_IRQHandler
- Default_Handler CPU0_PPU_IRQHandler
- Default_Handler CPU1_PPU_IRQHandler
- Default_Handler CPU0_DGB_PPU_IRQHandler
- Default_Handler CPU1_DGB_PPU_IRQHandler
- Default_Handler CRYPTOCELL_PPU_IRQHandler
- Default_Handler RAM0_PPU_IRQHandler
- Default_Handler RAM1_PPU_IRQHandler
- Default_Handler RAM2_PPU_IRQHandler
- Default_Handler RAM3_PPU_IRQHandler
- Default_Handler DEBUG_PPU_IRQHandler
- Default_Handler CPU0_CTI_IRQHandler
- Default_Handler CPU1_CTI_IRQHandler
-
- Default_Handler GpTimer_IRQHandler
- Default_Handler I2C0_IRQHandler
- Default_Handler I2C1_IRQHandler
- Default_Handler I2S_IRQHandler
- Default_Handler SPI_IRQHandler
- Default_Handler QSPI_IRQHandler
- Default_Handler UARTRX0_Handler
- Default_Handler UARTTX0_Handler
- Default_Handler UART0_RxTimeout_IRQHandler
- Default_Handler UART0_ModemStatus_IRQHandler
- Default_Handler UART0_Error_IRQHandler
- Default_Handler UART0_IRQHandler
- Default_Handler UARTRX1_Handler
- Default_Handler UARTTX1_Handler
- Default_Handler UART1_RxTimeout_IRQHandler
- Default_Handler UART1_ModemStatus_IRQHandler
- Default_Handler UART1_Error_IRQHandler
- Default_Handler UART1_IRQHandler
- Default_Handler GPIO_0_IRQHandler
- Default_Handler GPIO_1_IRQHandler
- Default_Handler GPIO_2_IRQHandler
- Default_Handler GPIO_3_IRQHandler
- Default_Handler GPIO_4_IRQHandler
- Default_Handler GPIO_5_IRQHandler
- Default_Handler GPIO_6_IRQHandler
- Default_Handler GPIO_7_IRQHandler
- Default_Handler GPIO_8_IRQHandler
- Default_Handler GPIO_9_IRQHandler
- Default_Handler GPIO_10_IRQHandler
- Default_Handler GPIO_11_IRQHandler
- Default_Handler GPIO_12_IRQHandler
- Default_Handler GPIO_13_IRQHandler
- Default_Handler GPIO_14_IRQHandler
- Default_Handler GPIO_15_IRQHandler
- Default_Handler Combined_IRQHandler
- Default_Handler PVT_IRQHandler
- Default_Handler PWM_0_IRQHandler
- Default_Handler RTC_IRQHandler
- Default_Handler GpTimer0_IRQHandler
- Default_Handler GpTimer1_IRQHandler
- Default_Handler PWM_1_IRQHandler
- Default_Handler PWM_2_IRQHandler
- Default_Handler IOMUX_IRQHandler
-
- ALIGN
-
- END
diff --git a/platform/ext/target/musca_a/Device/Source/armclang/startup_cmsdk_musca_ns.s b/platform/ext/target/musca_a/Device/Source/armclang/startup_cmsdk_musca_ns.s
deleted file mode 100644
index bbb0900..0000000
--- a/platform/ext/target/musca_a/Device/Source/armclang/startup_cmsdk_musca_ns.s
+++ /dev/null
@@ -1,243 +0,0 @@
-;/*
-; * Copyright (c) 2017-2020 ARM Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; */
-;
-; This file is derivative of CMSIS V5.01 startup_ARMv8MML.s
-; Git SHA: 8a1d9d6ee18b143ae5befefa14d89fb5b3f99c75
-
-;/*
-;//-------- <<< Use Configuration Wizard in Context Menu >>> ------------------
-;*/
-
-
-; <h> Stack Configuration
-; <o> Stack Size (in Bytes) <0x0-0xFFFFFFFF:8>
-; </h>
-
- IMPORT |Image$$ARM_LIB_STACK_MSP$$ZI$$Limit|
-
-; Vector Table Mapped to Address 0 at Reset
-
- AREA RESET, DATA, READONLY
- EXPORT __Vectors
- EXPORT __Vectors_End
- EXPORT __Vectors_Size
-
-__Vectors ;Core Interrupts
- DCD |Image$$ARM_LIB_STACK_MSP$$ZI$$Limit| ; Top of Stack
- DCD Reset_Handler ; Reset Handler
- DCD NMI_Handler ; NMI Handler
- DCD HardFault_Handler ; Hard Fault Handler
- DCD MemManage_Handler ; MPU Fault Handler
- DCD BusFault_Handler ; Bus Fault Handler
- DCD UsageFault_Handler ; Usage Fault Handler
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD SVC_Handler ; SVCall Handler
- DCD DebugMon_Handler ; Debug Monitor Handler
- DCD 0 ; Reserved
- DCD PendSV_Handler ; PendSV Handler
- DCD SysTick_Handler ; SysTick Handler
- ;SSE-200 Interrupts
- DCD NS_WATCHDOG_RESET_IRQHandler ; 0: Non-Secure Watchdog Reset Request Interrupt
- DCD NS_WATCHDOG_IRQHandler ; 1: Non-Secure Watchdog Interrupt
- DCD S32K_TIMER_IRQHandler ; 2: S32K Timer Interrupt
- DCD TIMER0_IRQHandler ; 3: CMSDK Timer 0 Interrupt
- DCD TIMER1_Handler ; 4: CMSDK Timer 1 Interrupt
- DCD DUALTIMER_IRQHandler ; 5: CMSDK Dual Timer Interrupt
- DCD MHU0_IRQHandler ; 6: Message Handling Unit 0 Interrupt
- DCD MHU1_IRQHandler ; 7: Message Handling Unit 1 Interrupt
- DCD CRYPTOCELL_IRQHandler ; 8: CryptoCell-312 Interrupt
- DCD 0 ; 9: Reserved
- DCD 0 ; 10: Reserved
- DCD 0 ; 11: Reserved
- DCD 0 ; 12: Reserved
- DCD I_CACHE_INV_ERR_IRQHandler ; 13: Intsruction Cache Invalidation Interrupt
- DCD 0 ; 14: Reserved
- DCD SYS_PPU_IRQHandler ; 15: System PPU Interrupt
- DCD CPU0_PPU_IRQHandler ; 16: CPU0 PPU Interrupt
- DCD CPU1_PPU_IRQHandler ; 17: CPU1 PPU Interrupt
- DCD CPU0_DGB_PPU_IRQHandler ; 18: CPU0 Debug PPU Interrupt
- DCD CPU1_DGB_PPU_IRQHandler ; 19: CPU1 Debug PPU Interrupt
- DCD CRYPTOCELL_PPU_IRQHandler ; 20: CryptoCell PPU Interrupt
- DCD 0 ; 21: Reserved
- DCD RAM0_PPU_IRQHandler ; 22: RAM 0 PPU Interrupt
- DCD RAM1_PPU_IRQHandler ; 23: RAM 1 PPU Interrupt
- DCD RAM2_PPU_IRQHandler ; 24: RAM 2 PPU Interrupt
- DCD RAM3_PPU_IRQHandler ; 25: RAM 3 PPU Interrupt
- DCD DEBUG_PPU_IRQHandler ; 26: Debug PPU Interrupt
- DCD 0 ; 27: Reserved
- DCD CPU0_CTI_IRQHandler ; 28: CPU0 CTI Interrupt
- DCD CPU1_CTI_IRQHandler ; 29: CPU1 CTI Interrupt
- DCD 0 ; 30: Reserved
- DCD 0 ; 31: Reserved
- ;Expansion Interrupts
- DCD 0 ; 32: Reserved
- DCD GpTimer_IRQHandler ; 33: General Purpose Timer
- DCD I2C0_IRQHandler ; 34: I2C0
- DCD I2C1_IRQHandler ; 35: I2C1
- DCD I2S_IRQHandler ; 36: I2S
- DCD SPI_IRQHandler ; 37: SPI
- DCD QSPI_IRQHandler ; 38: QSPI
- DCD UARTRX0_Handler ; 39: UART0 receive FIFO interrupt
- DCD UARTTX0_Handler ; 40: UART0 transmit FIFO interrupt
- DCD UART0_RxTimeout_IRQHandler ; 41: UART0 receive timeout interrupt
- DCD UART0_ModemStatus_IRQHandler ; 42: UART0 modem status interrupt
- DCD UART0_Error_IRQHandler ; 43: UART0 error interrupt
- DCD UART0_IRQHandler ; 44: UART0 interrupt
- DCD UARTRX1_Handler ; 45: UART0 receive FIFO interrupt
- DCD UARTTX1_Handler ; 46: UART0 transmit FIFO interrupt
- DCD UART1_RxTimeout_IRQHandler ; 47: UART0 receive timeout interrupt
- DCD UART1_ModemStatus_IRQHandler ; 48: UART0 modem status interrupt
- DCD UART1_Error_IRQHandler ; 49: UART0 error interrupt
- DCD UART1_IRQHandler ; 50: UART0 interrupt
- DCD GPIO_0_IRQHandler ; 51: GPIO 0 interrupt
- DCD GPIO_1_IRQHandler ; 52: GPIO 1 interrupt
- DCD GPIO_2_IRQHandler ; 53: GPIO 2 interrupt
- DCD GPIO_3_IRQHandler ; 54: GPIO 3 interrupt
- DCD GPIO_4_IRQHandler ; 55: GPIO 4 interrupt
- DCD GPIO_5_IRQHandler ; 56: GPIO 5 interrupt
- DCD GPIO_6_IRQHandler ; 57: GPIO 6 interrupt
- DCD GPIO_7_IRQHandler ; 58: GPIO 7 interrupt
- DCD GPIO_8_IRQHandler ; 59: GPIO 8 interrupt
- DCD GPIO_9_IRQHandler ; 60: GPIO 9 interrupt
- DCD GPIO_10_IRQHandler ; 61: GPIO 10 interrupt
- DCD GPIO_11_IRQHandler ; 62: GPIO 11 interrupt
- DCD GPIO_12_IRQHandler ; 63: GPIO 12 interrupt
- DCD GPIO_13_IRQHandler ; 64: GPIO 13 interrupt
- DCD GPIO_14_IRQHandler ; 65: GPIO 14 interrupt
- DCD GPIO_15_IRQHandler ; 66: GPIO 15 interrupt
- DCD Combined_IRQHandler ; 67: Combined interrupt
- DCD PVT_IRQHandler ; 68: PVT sensor interrupt
- DCD 0 ; 69: Reserved
- DCD PWM_0_IRQHandler ; 70: PWM0 interrupt
- DCD RTC_IRQHandler ; 71: RTC interrupt
- DCD GpTimer0_IRQHandler ; 72: General Purpose Timer0
- DCD GpTimer1_IRQHandler ; 73: General Purpose Timer1
- DCD PWM_1_IRQHandler ; 74: PWM1 interrupt
- DCD PWM_2_IRQHandler ; 75: PWM2 interrupt
- DCD IOMUX_IRQHandler ; 76: IOMUX interrupt
-
-__Vectors_End
-
-__Vectors_Size EQU __Vectors_End - __Vectors
-
-; Reset Handler
- AREA |.text|, CODE, READONLY
-Reset_Handler PROC
- EXPORT Reset_Handler [WEAK]
- IMPORT __main
- MRS R0, control ; Get control value
- ORR R0, R0, #2 ; Select switch to PSP
- MSR control, R0
- LDR R0, =__main
- BX R0
- ENDP
-End_Of_Main
- B .
-
-
-; Dummy Exception Handlers (infinite loops which can be modified)
- MACRO
- Default_Handler $handler_name
-$handler_name PROC
- EXPORT $handler_name [WEAK]
- B .
- ENDP
- MEND
-
- Default_Handler NMI_Handler
- Default_Handler HardFault_Handler
- Default_Handler MemManage_Handler
- Default_Handler BusFault_Handler
- Default_Handler UsageFault_Handler
- Default_Handler SVC_Handler
- Default_Handler DebugMon_Handler
- Default_Handler PendSV_Handler
- Default_Handler SysTick_Handler
-
- Default_Handler NS_WATCHDOG_RESET_IRQHandler
- Default_Handler NS_WATCHDOG_IRQHandler
- Default_Handler S32K_TIMER_IRQHandler
- Default_Handler TIMER0_IRQHandler
- Default_Handler TIMER1_Handler
- Default_Handler DUALTIMER_IRQHandler
- Default_Handler MHU0_IRQHandler
- Default_Handler MHU1_IRQHandler
- Default_Handler CRYPTOCELL_IRQHandler
- Default_Handler I_CACHE_INV_ERR_IRQHandler
- Default_Handler SYS_PPU_IRQHandler
- Default_Handler CPU0_PPU_IRQHandler
- Default_Handler CPU1_PPU_IRQHandler
- Default_Handler CPU0_DGB_PPU_IRQHandler
- Default_Handler CPU1_DGB_PPU_IRQHandler
- Default_Handler CRYPTOCELL_PPU_IRQHandler
- Default_Handler RAM0_PPU_IRQHandler
- Default_Handler RAM1_PPU_IRQHandler
- Default_Handler RAM2_PPU_IRQHandler
- Default_Handler RAM3_PPU_IRQHandler
- Default_Handler DEBUG_PPU_IRQHandler
- Default_Handler CPU0_CTI_IRQHandler
- Default_Handler CPU1_CTI_IRQHandler
-
- Default_Handler GpTimer_IRQHandler
- Default_Handler I2C0_IRQHandler
- Default_Handler I2C1_IRQHandler
- Default_Handler I2S_IRQHandler
- Default_Handler SPI_IRQHandler
- Default_Handler QSPI_IRQHandler
- Default_Handler UARTRX0_Handler
- Default_Handler UARTTX0_Handler
- Default_Handler UART0_RxTimeout_IRQHandler
- Default_Handler UART0_ModemStatus_IRQHandler
- Default_Handler UART0_Error_IRQHandler
- Default_Handler UART0_IRQHandler
- Default_Handler UARTRX1_Handler
- Default_Handler UARTTX1_Handler
- Default_Handler UART1_RxTimeout_IRQHandler
- Default_Handler UART1_ModemStatus_IRQHandler
- Default_Handler UART1_Error_IRQHandler
- Default_Handler UART1_IRQHandler
- Default_Handler GPIO_0_IRQHandler
- Default_Handler GPIO_1_IRQHandler
- Default_Handler GPIO_2_IRQHandler
- Default_Handler GPIO_3_IRQHandler
- Default_Handler GPIO_4_IRQHandler
- Default_Handler GPIO_5_IRQHandler
- Default_Handler GPIO_6_IRQHandler
- Default_Handler GPIO_7_IRQHandler
- Default_Handler GPIO_8_IRQHandler
- Default_Handler GPIO_9_IRQHandler
- Default_Handler GPIO_10_IRQHandler
- Default_Handler GPIO_11_IRQHandler
- Default_Handler GPIO_12_IRQHandler
- Default_Handler GPIO_13_IRQHandler
- Default_Handler GPIO_14_IRQHandler
- Default_Handler GPIO_15_IRQHandler
- Default_Handler Combined_IRQHandler
- Default_Handler PVT_IRQHandler
- Default_Handler PWM_0_IRQHandler
- Default_Handler RTC_IRQHandler
- Default_Handler GpTimer0_IRQHandler
- Default_Handler GpTimer1_IRQHandler
- Default_Handler PWM_1_IRQHandler
- Default_Handler PWM_2_IRQHandler
- Default_Handler IOMUX_IRQHandler
-
- ALIGN
-
- END
diff --git a/platform/ext/target/musca_a/Device/Source/armclang/startup_cmsdk_musca_s.s b/platform/ext/target/musca_a/Device/Source/armclang/startup_cmsdk_musca_s.s
deleted file mode 100644
index 547544a..0000000
--- a/platform/ext/target/musca_a/Device/Source/armclang/startup_cmsdk_musca_s.s
+++ /dev/null
@@ -1,252 +0,0 @@
-;/*
-; * Copyright (c) 2017-2019 Arm Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; */
-;
-; This file is derivative of CMSIS V5.01 startup_ARMv8MML.s
-; Git SHA: 8a1d9d6ee18b143ae5befefa14d89fb5b3f99c75
-
-;/*
-;//-------- <<< Use Configuration Wizard in Context Menu >>> ------------------
-;*/
-
-
-; <h> Stack Configuration
-; <o> Stack Size (in Bytes) <0x0-0xFFFFFFFF:8>
-; </h>
-
- IMPORT |Image$$ARM_LIB_STACK_MSP$$ZI$$Limit|
-
-; Vector Table Mapped to Address 0 at Reset
-
- AREA RESET, DATA, READONLY
- EXPORT __Vectors
- EXPORT __Vectors_End
- EXPORT __Vectors_Size
-
-__Vectors ;Core Interrupts
- DCD |Image$$ARM_LIB_STACK_MSP$$ZI$$Limit| ; Top of Stack
- DCD Reset_Handler ; Reset Handler
- DCD NMI_Handler ; NMI Handler
- DCD HardFault_Handler ; Hard Fault Handler
- DCD MemManage_Handler ; MPU Fault Handler
- DCD BusFault_Handler ; Bus Fault Handler
- DCD UsageFault_Handler ; Usage Fault Handler
- DCD SecureFault_Handler ; Secure Fault Handler
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD SVC_Handler ; SVCall Handler
- DCD DebugMon_Handler ; Debug Monitor Handler
- DCD 0 ; Reserved
- DCD PendSV_Handler ; PendSV Handler
- DCD SysTick_Handler ; SysTick Handler
- ;SSE-200 Interrupts
- DCD NS_WATCHDOG_RESET_IRQHandler ; 0: Non-Secure Watchdog Reset Request Interrupt
- DCD NS_WATCHDOG_IRQHandler ; 1: Non-Secure Watchdog Interrupt
- DCD S32K_TIMER_IRQHandler ; 2: S32K Timer Interrupt
- DCD TFM_TIMER0_IRQ_Handler ; 3: CMSDK Timer 0 Interrupt
- DCD TIMER1_IRQHandler ; 4: CMSDK Timer 1 Interrupt
- DCD DUALTIMER_IRQHandler ; 5: CMSDK Dual Timer Interrupt
- DCD MHU0_IRQHandler ; 6: Message Handling Unit 0 Interrupt
- DCD MHU1_IRQHandler ; 7: Message Handling Unit 1 Interrupt
- DCD CRYPTOCELL_IRQHandler ; 8: CryptoCell-312 Interrupt
- DCD MPC_Handler ; 9: Secure Combined MPC Interrupt
- DCD PPC_Handler ; 10: Secure Combined PPC Interrupt
- DCD S_MSC_COMBINED_IRQHandler ; 11: Secure Combined MSC Interrupt
- DCD S_BRIDGE_ERR_IRQHandler ; 12: Secure Bridge Error Combined Interrupt
- DCD I_CACHE_INV_ERR_IRQHandler ; 13: Intsruction Cache Invalidation Interrupt
- DCD 0 ; 14: Reserved
- DCD SYS_PPU_IRQHandler ; 15: System PPU Interrupt
- DCD CPU0_PPU_IRQHandler ; 16: CPU0 PPU Interrupt
- DCD CPU1_PPU_IRQHandler ; 17: CPU1 PPU Interrupt
- DCD CPU0_DGB_PPU_IRQHandler ; 18: CPU0 Debug PPU Interrupt
- DCD CPU1_DGB_PPU_IRQHandler ; 19: CPU1 Debug PPU Interrupt
- DCD CRYPTOCELL_PPU_IRQHandler ; 20: CryptoCell PPU Interrupt
- DCD 0 ; 21: Reserved
- DCD RAM0_PPU_IRQHandler ; 22: RAM 0 PPU Interrupt
- DCD RAM1_PPU_IRQHandler ; 23: RAM 1 PPU Interrupt
- DCD RAM2_PPU_IRQHandler ; 24: RAM 2 PPU Interrupt
- DCD RAM3_PPU_IRQHandler ; 25: RAM 3 PPU Interrupt
- DCD DEBUG_PPU_IRQHandler ; 26: Debug PPU Interrupt
- DCD 0 ; 27: Reserved
- DCD CPU0_CTI_IRQHandler ; 28: CPU0 CTI Interrupt
- DCD CPU1_CTI_IRQHandler ; 29: CPU1 CTI Interrupt
- DCD 0 ; 30: Reserved
- DCD 0 ; 31: Reserved
- ;Expansion Interrupts
- DCD 0 ; 32: Reserved
- DCD GpTimer_IRQHandler ; 33: General Purpose Timer
- DCD I2C0_IRQHandler ; 34: I2C0
- DCD I2C1_IRQHandler ; 35: I2C1
- DCD I2S_IRQHandler ; 36: I2S
- DCD SPI_IRQHandler ; 37: SPI
- DCD QSPI_IRQHandler ; 38: QSPI
- DCD UARTRX0_Handler ; 39: UART0 receive FIFO interrupt
- DCD UARTTX0_Handler ; 40: UART0 transmit FIFO interrupt
- DCD UART0_RxTimeout_IRQHandler ; 41: UART0 receive timeout interrupt
- DCD UART0_ModemStatus_IRQHandler ; 42: UART0 modem status interrupt
- DCD UART0_Error_IRQHandler ; 43: UART0 error interrupt
- DCD UART0_IRQHandler ; 44: UART0 interrupt
- DCD UARTRX1_Handler ; 45: UART0 receive FIFO interrupt
- DCD UARTTX1_Handler ; 46: UART0 transmit FIFO interrupt
- DCD UART1_RxTimeout_IRQHandler ; 47: UART0 receive timeout interrupt
- DCD UART1_ModemStatus_IRQHandler ; 48: UART0 modem status interrupt
- DCD UART1_Error_IRQHandler ; 49: UART0 error interrupt
- DCD UART1_IRQHandler ; 50: UART0 interrupt
- DCD GPIO_0_IRQHandler ; 51: GPIO 0 interrupt
- DCD GPIO_1_IRQHandler ; 52: GPIO 1 interrupt
- DCD GPIO_2_IRQHandler ; 53: GPIO 2 interrupt
- DCD GPIO_3_IRQHandler ; 54: GPIO 3 interrupt
- DCD GPIO_4_IRQHandler ; 55: GPIO 4 interrupt
- DCD GPIO_5_IRQHandler ; 56: GPIO 5 interrupt
- DCD GPIO_6_IRQHandler ; 57: GPIO 6 interrupt
- DCD GPIO_7_IRQHandler ; 58: GPIO 7 interrupt
- DCD GPIO_8_IRQHandler ; 59: GPIO 8 interrupt
- DCD GPIO_9_IRQHandler ; 60: GPIO 9 interrupt
- DCD GPIO_10_IRQHandler ; 61: GPIO 10 interrupt
- DCD GPIO_11_IRQHandler ; 62: GPIO 11 interrupt
- DCD GPIO_12_IRQHandler ; 63: GPIO 12 interrupt
- DCD GPIO_13_IRQHandler ; 64: GPIO 13 interrupt
- DCD GPIO_14_IRQHandler ; 65: GPIO 14 interrupt
- DCD GPIO_15_IRQHandler ; 66: GPIO 15 interrupt
- DCD Combined_IRQHandler ; 67: Combined interrupt
- DCD PVT_IRQHandler ; 68: PVT sensor interrupt
- DCD 0 ; 69: Reserved
- DCD PWM_0_IRQHandler ; 70: PWM0 interrupt
- DCD RTC_IRQHandler ; 71: RTC interrupt
- DCD GpTimer0_IRQHandler ; 72: General Purpose Timer0
- DCD GpTimer1_IRQHandler ; 73: General Purpose Timer1
- DCD PWM_1_IRQHandler ; 74: PWM1 interrupt
- DCD PWM_2_IRQHandler ; 75: PWM2 interrupt
- DCD IOMUX_IRQHandler ; 76: IOMUX interrupt
-
-__Vectors_End
-
-__Vectors_Size EQU __Vectors_End - __Vectors
-
-; Reset Handler
- AREA |.text|, CODE, READONLY
-Reset_Handler PROC
- EXPORT Reset_Handler [WEAK]
- IMPORT SystemInit
- IMPORT __main
- CPSID i ; Disable IRQs
- LDR R0, =SystemInit
- BLX R0
- MRS R0, control ; Get control value
- ORR R0, R0, #2 ; Select switch to PSP
- MSR control, R0
- LDR R0, =__main
- BX R0
- ENDP
-End_Of_Main
- B .
-
-
-; Dummy Exception Handlers (infinite loops which can be modified)
- MACRO
- Default_Handler $handler_name
-$handler_name PROC
- EXPORT $handler_name [WEAK]
- B .
- ENDP
- MEND
-
- Default_Handler NMI_Handler
- Default_Handler HardFault_Handler
- Default_Handler MemManage_Handler
- Default_Handler BusFault_Handler
- Default_Handler UsageFault_Handler
- Default_Handler SecureFault_Handler
- Default_Handler SVC_Handler
- Default_Handler DebugMon_Handler
- Default_Handler PendSV_Handler
- Default_Handler SysTick_Handler
-
- Default_Handler NS_WATCHDOG_RESET_IRQHandler
- Default_Handler NS_WATCHDOG_IRQHandler
- Default_Handler S32K_TIMER_IRQHandler
- Default_Handler TFM_TIMER0_IRQ_Handler
- Default_Handler TIMER1_IRQHandler
- Default_Handler DUALTIMER_IRQHandler
- Default_Handler MHU0_IRQHandler
- Default_Handler MHU1_IRQHandler
- Default_Handler CRYPTOCELL_IRQHandler
- Default_Handler MPC_Handler
- Default_Handler PPC_Handler
- Default_Handler S_MSC_COMBINED_IRQHandler
- Default_Handler S_BRIDGE_ERR_IRQHandler
- Default_Handler I_CACHE_INV_ERR_IRQHandler
- Default_Handler SYS_PPU_IRQHandler
- Default_Handler CPU0_PPU_IRQHandler
- Default_Handler CPU1_PPU_IRQHandler
- Default_Handler CPU0_DGB_PPU_IRQHandler
- Default_Handler CPU1_DGB_PPU_IRQHandler
- Default_Handler CRYPTOCELL_PPU_IRQHandler
- Default_Handler RAM0_PPU_IRQHandler
- Default_Handler RAM1_PPU_IRQHandler
- Default_Handler RAM2_PPU_IRQHandler
- Default_Handler RAM3_PPU_IRQHandler
- Default_Handler DEBUG_PPU_IRQHandler
- Default_Handler CPU0_CTI_IRQHandler
- Default_Handler CPU1_CTI_IRQHandler
-
- Default_Handler GpTimer_IRQHandler
- Default_Handler I2C0_IRQHandler
- Default_Handler I2C1_IRQHandler
- Default_Handler I2S_IRQHandler
- Default_Handler SPI_IRQHandler
- Default_Handler QSPI_IRQHandler
- Default_Handler UARTRX0_Handler
- Default_Handler UARTTX0_Handler
- Default_Handler UART0_RxTimeout_IRQHandler
- Default_Handler UART0_ModemStatus_IRQHandler
- Default_Handler UART0_Error_IRQHandler
- Default_Handler UART0_IRQHandler
- Default_Handler UARTRX1_Handler
- Default_Handler UARTTX1_Handler
- Default_Handler UART1_RxTimeout_IRQHandler
- Default_Handler UART1_ModemStatus_IRQHandler
- Default_Handler UART1_Error_IRQHandler
- Default_Handler UART1_IRQHandler
- Default_Handler GPIO_0_IRQHandler
- Default_Handler GPIO_1_IRQHandler
- Default_Handler GPIO_2_IRQHandler
- Default_Handler GPIO_3_IRQHandler
- Default_Handler GPIO_4_IRQHandler
- Default_Handler GPIO_5_IRQHandler
- Default_Handler GPIO_6_IRQHandler
- Default_Handler GPIO_7_IRQHandler
- Default_Handler GPIO_8_IRQHandler
- Default_Handler GPIO_9_IRQHandler
- Default_Handler GPIO_10_IRQHandler
- Default_Handler GPIO_11_IRQHandler
- Default_Handler GPIO_12_IRQHandler
- Default_Handler GPIO_13_IRQHandler
- Default_Handler GPIO_14_IRQHandler
- Default_Handler GPIO_15_IRQHandler
- Default_Handler Combined_IRQHandler
- Default_Handler PVT_IRQHandler
- Default_Handler PWM_0_IRQHandler
- Default_Handler RTC_IRQHandler
- Default_Handler GpTimer0_IRQHandler
- Default_Handler GpTimer1_IRQHandler
- Default_Handler PWM_1_IRQHandler
- Default_Handler PWM_2_IRQHandler
- Default_Handler IOMUX_IRQHandler
-
- ALIGN
-
- END
diff --git a/platform/ext/target/musca_a/Device/Source/device_definition.c b/platform/ext/target/musca_a/Device/Source/device_definition.c
deleted file mode 100644
index 240f78b..0000000
--- a/platform/ext/target/musca_a/Device/Source/device_definition.c
+++ /dev/null
@@ -1,636 +0,0 @@
-/*
- * Copyright (c) 2017-2021 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing software
- * distributed under the License is distributed on an "AS IS" BASIS
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file device_definition.c
- * \brief This file defines exports the structures based on the peripheral
- * definitions from device_cfg.h.
- * This file is meant to be used as a helper for baremetal
- * applications and/or as an example of how to configure the generic
- * driver structures.
- */
-
-#include "device_cfg.h"
-#include "device_definition.h"
-#include "platform_base_address.h"
-#include "tfm_plat_defs.h"
-
-/* ======= Peripheral configuration structure definitions ======= */
-/* MUSCA A1 SCC driver structures */
-#ifdef MUSCA_A1_SCC_S
-static const struct musca_a1_scc_dev_cfg_t MUSCA_A1_SCC_DEV_CFG_S = {
- .base = MUSCA_SCC_S_BASE};
-struct musca_a1_scc_dev_t MUSCA_A1_SCC_DEV_S = {&(MUSCA_A1_SCC_DEV_CFG_S)};
-#endif
-#ifdef MUSCA_A1_SCC_NS
-static const struct musca_a1_scc_dev_cfg_t MUSCA_A1_SCC_DEV_CFG_NS = {
- .base = MUSCA_SCC_NS_BASE};
-struct musca_a1_scc_dev_t MUSCA_A1_SCC_DEV_NS = {&(MUSCA_A1_SCC_DEV_CFG_NS)};
-#endif
-
-/* CMSDK GPIO driver structures */
-#ifdef GPIO0_CMSDK_S
-static const struct gpio_cmsdk_dev_cfg_t GPIO0_CMSDK_DEV_CFG_S = {
- .base = MUSCA_GPIO_S_BASE};
-struct gpio_cmsdk_dev_t GPIO0_CMSDK_DEV_S = {&(GPIO0_CMSDK_DEV_CFG_S)};
-#endif
-
-/* ARM PPC SSE 200 driver structures */
-#ifdef AHB_PPC0_S
-static struct ppc_sse200_dev_cfg_t AHB_PPC0_DEV_CFG_S = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t AHB_PPC0_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t AHB_PPC0_DEV_S = {
- &AHB_PPC0_DEV_CFG_S, &AHB_PPC0_DEV_DATA_S };
-#endif
-
-#ifdef AHB_PPCEXP0_S
-static struct ppc_sse200_dev_cfg_t AHB_PPCEXP0_DEV_CFG_S = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t AHB_PPCEXP0_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t AHB_PPCEXP0_DEV_S = {
- &AHB_PPCEXP0_DEV_CFG_S, &AHB_PPCEXP0_DEV_DATA_S };
-#endif
-
-#ifdef AHB_PPCEXP1_S
-static struct ppc_sse200_dev_cfg_t AHB_PPCEXP1_DEV_CFG_S = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t AHB_PPCEXP1_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t AHB_PPCEXP1_DEV_S = {
- &AHB_PPCEXP1_DEV_CFG_S, &AHB_PPCEXP1_DEV_DATA_S };
-#endif
-
-#ifdef AHB_PPCEXP2_S
-static struct ppc_sse200_dev_cfg_t AHB_PPCEXP2_DEV_CFG_S = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t AHB_PPCEXP2_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t AHB_PPCEXP2_DEV_S = {
- &AHB_PPCEXP2_DEV_CFG_S, &AHB_PPCEXP2_DEV_DATA_S };
-#endif
-
-#ifdef AHB_PPCEXP3_S
-static struct ppc_sse200_dev_cfg_t AHB_PPCEXP3_DEV_CFG_S = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t AHB_PPCEXP3_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t AHB_PPCEXP3_DEV_S = {
- &AHB_PPCEXP3_DEV_CFG_S, &AHB_PPCEXP3_DEV_DATA_S };
-#endif
-
-#ifdef APB_PPC0_S
-static struct ppc_sse200_dev_cfg_t APB_PPC0_DEV_CFG_S = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t APB_PPC0_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t APB_PPC0_DEV_S = {
- &APB_PPC0_DEV_CFG_S, &APB_PPC0_DEV_DATA_S };
-#endif
-
-#ifdef APB_PPC1_S
-static struct ppc_sse200_dev_cfg_t APB_PPC1_DEV_CFG_S = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t APB_PPC1_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t APB_PPC1_DEV_S = {
- &APB_PPC1_DEV_CFG_S, &APB_PPC1_DEV_DATA_S};
-#endif
-
-#ifdef APB_PPCEXP0_S
-static struct ppc_sse200_dev_cfg_t APB_PPCEXP0_DEV_CFG_S = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t APB_PPCEXP0_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t APB_PPCEXP0_DEV_S = {
- &APB_PPCEXP0_DEV_CFG_S, &APB_PPCEXP0_DEV_DATA_S };
-#endif
-
-#ifdef APB_PPCEXP1_S
-static struct ppc_sse200_dev_cfg_t APB_PPCEXP1_DEV_CFG = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t APB_PPCEXP1_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t APB_PPCEXP1_DEV_S = {
- &APB_PPCEXP1_DEV_CFG, &APB_PPCEXP1_DEV_DATA_S };
-#endif
-
-#ifdef APB_PPCEXP2_S
-static struct ppc_sse200_dev_cfg_t APB_PPCEXP2_DEV_CFG = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t APB_PPCEXP2_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t APB_PPCEXP2_DEV_S = {
- &APB_PPCEXP2_DEV_CFG, &APB_PPCEXP2_DEV_DATA_S };
-#endif
-
-#ifdef APB_PPCEXP3_S
-static struct ppc_sse200_dev_cfg_t APB_PPCEXP3_DEV_CFG = {
- .spctrl_base = MUSCA_SPCTRL_S_BASE,
- .nspctrl_base = MUSCA_NSPCTRL_NS_BASE };
-static struct ppc_sse200_dev_data_t APB_PPCEXP3_DEV_DATA_S = {
- .p_ns_ppc = 0,
- .p_sp_ppc = 0,
- .p_nsp_ppc = 0,
- .int_bit_mask = 0,
- .state = 0 };
-struct ppc_sse200_dev_t APB_PPCEXP3_DEV_S = {
- &APB_PPCEXP3_DEV_CFG, &APB_PPCEXP3_DEV_DATA_S };
-#endif
-
-/* ARM MPC SIE 200 driver structures */
-#ifdef MPC_ISRAM0_S
-static const struct mpc_sie200_dev_cfg_t MPC_ISRAM0_DEV_CFG_S = {
- .base = MUSCA_MPC_SRAM0_S_BASE};
-static struct mpc_sie200_dev_data_t MPC_ISRAM0_DEV_DATA_S = {
- .range_list = 0,
- .nbr_of_ranges = 0,
- .state = 0,
- .reserved = 0};
-struct mpc_sie200_dev_t MPC_ISRAM0_DEV_S = {
- &(MPC_ISRAM0_DEV_CFG_S),
- &(MPC_ISRAM0_DEV_DATA_S)};
-#endif
-
-#ifdef MPC_ISRAM1_S
-static const struct mpc_sie200_dev_cfg_t MPC_ISRAM1_DEV_CFG_S = {
- .base = MUSCA_MPC_SRAM1_S_BASE};
-static struct mpc_sie200_dev_data_t MPC_ISRAM1_DEV_DATA_S = {
- .range_list = 0,
- .nbr_of_ranges = 0,
- .state = 0,
- .reserved = 0};
-struct mpc_sie200_dev_t MPC_ISRAM1_DEV_S = {
- &(MPC_ISRAM1_DEV_CFG_S),
- &(MPC_ISRAM1_DEV_DATA_S)};
-#endif
-
-#ifdef MPC_ISRAM2_S
-static const struct mpc_sie200_dev_cfg_t MPC_ISRAM2_DEV_CFG_S = {
- .base = MUSCA_MPC_SRAM2_S_BASE};
-static struct mpc_sie200_dev_data_t MPC_ISRAM2_DEV_DATA_S = {
- .range_list = 0,
- .nbr_of_ranges = 0,
- .state = 0,
- .reserved = 0};
-struct mpc_sie200_dev_t MPC_ISRAM2_DEV_S = {
- &(MPC_ISRAM2_DEV_CFG_S),
- &(MPC_ISRAM2_DEV_DATA_S)};
-#endif
-
-#ifdef MPC_ISRAM3_S
-static const struct mpc_sie200_dev_cfg_t MPC_ISRAM3_DEV_CFG_S = {
- .base = MUSCA_MPC_SRAM3_S_BASE};
-static struct mpc_sie200_dev_data_t MPC_ISRAM3_DEV_DATA_S = {
- .range_list = 0,
- .nbr_of_ranges = 0,
- .state = 0,
- .reserved = 0};
-struct mpc_sie200_dev_t MPC_ISRAM3_DEV_S = {
- &(MPC_ISRAM3_DEV_CFG_S),
- &(MPC_ISRAM3_DEV_DATA_S)};
-#endif
-
-#ifdef MPC_CODE_SRAM_NS
-static const struct mpc_sie200_dev_cfg_t MPC_CODE_SRAM_DEV_CFG_NS = {
- .base = MUSCA_CODE_SRAM_MPC_NS_BASE};
-static struct mpc_sie200_dev_data_t MPC_CODE_SRAM_DEV_DATA_NS = {
- .range_list = 0,
- .nbr_of_ranges = 0,
- .state = 0,
- .reserved = 0};
-struct mpc_sie200_dev_t MPC_CODE_SRAM_DEV_NS = {
- &(MPC_CODE_SRAM_DEV_CFG_NS),
- &(MPC_CODE_SRAM_DEV_DATA_NS)};
-#endif
-
-#ifdef MPC_CODE_SRAM_S
-static const struct mpc_sie200_dev_cfg_t MPC_CODE_SRAM_DEV_CFG_S = {
- .base = MUSCA_CODE_SRAM_MPC_S_BASE};
-static struct mpc_sie200_dev_data_t MPC_CODE_SRAM_DEV_DATA_S = {
- .range_list = 0,
- .nbr_of_ranges = 0,
- .state = 0,
- .reserved = 0};
-struct mpc_sie200_dev_t MPC_CODE_SRAM_DEV_S = {
- &(MPC_CODE_SRAM_DEV_CFG_S),
- &(MPC_CODE_SRAM_DEV_DATA_S)};
-#endif
-
-#ifdef MPC_QSPI_S
-static const struct mpc_sie200_dev_cfg_t MPC_QSPI_DEV_CFG_S = {
- .base = MUSCA_QSPI_MPC_S_BASE};
-static struct mpc_sie200_dev_data_t MPC_QSPI_DEV_DATA_S = {
- .range_list = 0,
- .nbr_of_ranges = 0,
- .state = 0,
- .reserved = 0};
-struct mpc_sie200_dev_t MPC_QSPI_DEV_S = {
- &(MPC_QSPI_DEV_CFG_S),
- &(MPC_QSPI_DEV_DATA_S)};
-#endif
-
-#ifdef MPC_QSPI_NS
-static const struct mpc_sie200_dev_cfg_t MPC_QSPI_DEV_CFG_NS = {
- .base = MUSCA_QSPI_MPC_NS_BASE};
-static struct mpc_sie200_dev_data_t MPC_QSPI_DEV_DATA_NS = {
- .range_list = 0,
- .nbr_of_ranges = 0,
- .state = 0,
- .reserved = 0};
-struct mpc_sie200_dev_t MPC_QSPI_DEV_NS = {
- &(MPC_QSPI_DEV_CFG_NS),
- &(MPC_QSPI_DEV_DATA_NS)};
-#endif
-
-/* ARM MHU driver structures */
-#ifdef ARM_MHU0_S
-static const struct arm_mhu_sse_200_dev_cfg_t ARM_MHU0_DEV_CFG_S = {
- .base = MUSCA_MHU0_S_BASE};
-struct arm_mhu_sse_200_dev_t ARM_MHU0_DEV_S = {&(ARM_MHU0_DEV_CFG_S)};
-#endif
-#ifdef ARM_MHU0_NS
-static const struct arm_mhu_sse_200_dev_cfg_t ARM_MHU0_DEV_CFG_NS = {
- .base = MUSCA_MHU0_NS_BASE};
-struct arm_mhu_sse_200_dev_t ARM_MHU0_DEV_NS = {&(ARM_MHU0_DEV_CFG_NS)};
-#endif
-
-#ifdef ARM_MHU1_S
-static const struct arm_mhu_sse_200_dev_cfg_t ARM_MHU1_DEV_CFG_S = {
- .base = MUSCA_MHU1_S_BASE};
-struct arm_mhu_sse_200_dev_t ARM_MHU1_DEV_S = {&(ARM_MHU1_DEV_CFG_S)};
-#endif
-#ifdef ARM_MHU1_NS
-static const struct arm_mhu_sse_200_dev_cfg_t ARM_MHU1_DEV_CFG_NS = {
- .base = MUSCA_MHU1_NS_BASE};
-struct arm_mhu_sse_200_dev_t ARM_MHU1_DEV_NS = {&(ARM_MHU1_DEV_CFG_NS)};
-#endif
-
-/* I2C IP6510 driver structures */
-#ifdef I2C0_IP6510_S
-static const struct i2c_ip6510_dev_cfg_t I2C0_IP6510_DEV_CFG_S = {
- .base = MUSCA_I2C0_S_BASE,
- .default_mode = I2C_IP6510_MASTER_MODE,
- .default_bus_speed = I2C_IP6510_SPEED_100KHZ};
-static struct i2c_ip6510_dev_data_t I2C0_IP6510_DEV_DATA_S = {
- .state = 0,
- .mode = 0,
- .bus_speed = 0};
-struct i2c_ip6510_dev_t I2C0_IP6510_DEV_S = {
- &(I2C0_IP6510_DEV_CFG_S),
- &(I2C0_IP6510_DEV_DATA_S)};
-#endif
-
-#ifdef I2C0_IP6510_NS
-static const struct i2c_ip6510_dev_cfg_t I2C0_IP6510_DEV_CFG_NS = {
- .base = MUSCA_I2C0_NS_BASE,
- .default_mode = I2C_IP6510_MASTER_MODE,
- .default_bus_speed = I2C_IP6510_SPEED_100KHZ};
-static struct i2c_ip6510_dev_data_t I2C0_IP6510_DEV_DATA_NS = {
- .state = 0,
- .mode = 0,
- .bus_speed = 0};
-struct i2c_ip6510_dev_t I2C0_IP6510_DEV_NS = {
- &(I2C0_IP6510_DEV_CFG_NS),
- &(I2C0_IP6510_DEV_DATA_NS)};
-#endif
-
-#ifdef I2C1_IP6510_S
-static const struct i2c_ip6510_dev_cfg_t I2C1_IP6510_DEV_CFG_S = {
- .base = MUSCA_I2C1_S_BASE,
- .default_mode = I2C_IP6510_MASTER_MODE,
- .default_bus_speed = I2C_IP6510_SPEED_100KHZ};
-static struct i2c_ip6510_dev_data_t I2C1_IP6510_DEV_DATA_S = {
- .state = 0,
- .mode = 0,
- .bus_speed = 0};
-struct i2c_ip6510_dev_t I2C1_IP6510_DEV_S = {
- &(I2C1_IP6510_DEV_CFG_S),
- &(I2C1_IP6510_DEV_DATA_S)};
-#endif
-
-#ifdef I2C1_IP6510_NS
-static const struct i2c_ip6510_dev_cfg_t I2C1_IP6510_DEV_CFG_NS = {
- .base = MUSCA_I2C1_NS_BASE,
- .default_mode = I2C_IP6510_MASTER_MODE,
- .default_bus_speed = I2C_IP6510_SPEED_100KHZ};
-static struct i2c_ip6510_dev_data_t I2C1_IP6510_DEV_DATA_NS = {
- .state = 0,
- .mode = 0,
- .bus_speed = 0};
-struct i2c_ip6510_dev_t I2C1_IP6510_DEV_NS = {
- &(I2C1_IP6510_DEV_CFG_NS),
- &(I2C1_IP6510_DEV_DATA_NS)};
-#endif
-
-/* CMSDK Timers driver structures */
-#ifdef CMSDK_TIMER0_S
-static const struct timer_cmsdk_dev_cfg_t CMSDK_TIMER0_DEV_CFG_S
- TFM_LINK_SET_RO_IN_PARTITION_SECTION("TFM_IRQ_TEST_1", "APP-ROT")
- = {.base = MUSCA_CMSDK_TIMER0_S_BASE};
-static struct timer_cmsdk_dev_data_t CMSDK_TIMER0_DEV_DATA_S
- TFM_LINK_SET_RW_IN_PARTITION_SECTION("TFM_IRQ_TEST_1", "APP-ROT")
- = {.is_initialized = 0};
-struct timer_cmsdk_dev_t CMSDK_TIMER0_DEV_S
- TFM_LINK_SET_RW_IN_PARTITION_SECTION("TFM_IRQ_TEST_1", "APP-ROT")
- = {&(CMSDK_TIMER0_DEV_CFG_S), &(CMSDK_TIMER0_DEV_DATA_S)};
-#endif
-#ifdef CMSDK_TIMER0_NS
-static const struct timer_cmsdk_dev_cfg_t CMSDK_TIMER0_DEV_CFG_NS = {
- .base = MUSCA_CMSDK_TIMER0_NS_BASE};
-static struct timer_cmsdk_dev_data_t CMSDK_TIMER0_DEV_DATA_NS = {
- .is_initialized = 0};
-struct timer_cmsdk_dev_t CMSDK_TIMER0_DEV_NS = {&(CMSDK_TIMER0_DEV_CFG_NS),
- &(CMSDK_TIMER0_DEV_DATA_NS)};
-#endif
-
-#ifdef CMSDK_TIMER1_S
-static const struct timer_cmsdk_dev_cfg_t CMSDK_TIMER1_DEV_CFG_S = {
- .base = MUSCA_CMSDK_TIMER1_S_BASE};
-static struct timer_cmsdk_dev_data_t CMSDK_TIMER1_DEV_DATA_S = {
- .is_initialized = 0};
-struct timer_cmsdk_dev_t CMSDK_TIMER1_DEV_S = {&(CMSDK_TIMER1_DEV_CFG_S),
- &(CMSDK_TIMER1_DEV_DATA_S)};
-#endif
-#ifdef CMSDK_TIMER1_NS
-static const struct timer_cmsdk_dev_cfg_t CMSDK_TIMER1_DEV_CFG_NS = {
- .base = MUSCA_CMSDK_TIMER1_NS_BASE};
-static struct timer_cmsdk_dev_data_t CMSDK_TIMER1_DEV_DATA_NS = {
- .is_initialized = 0};
-struct timer_cmsdk_dev_t CMSDK_TIMER1_DEV_NS = {&(CMSDK_TIMER1_DEV_CFG_NS),
- &(CMSDK_TIMER1_DEV_DATA_NS)};
-#endif
-
-/* CMSDK Dualtimer driver structures */
-#ifdef CMSDK_DUALTIMER_S
-static const struct dualtimer_cmsdk_dev_cfg_t CMSDK_DUALTIMER_DEV_CFG_S = {
- .base = MUSCA_CMSDK_DUALTIMER_S_BASE};
-static struct dualtimer_cmsdk_dev_data_t CMSDK_DUALTIMER_DEV_DATA_S = {
- .is_initialized = 0};
-
-struct dualtimer_cmsdk_dev_t CMSDK_DUALTIMER_DEV_S = {
- &(CMSDK_DUALTIMER_DEV_CFG_S),
- &(CMSDK_DUALTIMER_DEV_DATA_S)};
-#endif
-
-#ifdef CMSDK_DUALTIMER_NS
-static const struct dualtimer_cmsdk_dev_cfg_t CMSDK_DUALTIMER_DEV_CFG_NS = {
- .base = MUSCA_CMSDK_DUALTIMER_NS_BASE};
-static struct dualtimer_cmsdk_dev_data_t CMSDK_DUALTIMER_DEV_DATA_NS = {
- .is_initialized = 0};
-
-struct dualtimer_cmsdk_dev_t CMSDK_DUALTIMER_DEV_NS = {
- &(CMSDK_DUALTIMER_DEV_CFG_NS),
- &(CMSDK_DUALTIMER_DEV_DATA_NS)};
-#endif
-
-/* General-Purpose Timer driver structures */
-#ifdef GP_TIMER_S
-static const struct timer_gp_dev_cfg_t GP_TIMER_DEV_CFG_S = {
- .base = MUSCA_TIMER_S_BASE};
-static struct timer_gp_dev_data_t GP_TIMER_DEV_DATA_S = {
- .is_initialized = false,
- .alarm0_init = 0,
- .alarm1_init = 0};
-struct timer_gp_dev_t GP_TIMER_DEV_S = {
- &(GP_TIMER_DEV_CFG_S),
- &(GP_TIMER_DEV_DATA_S)};
-#endif
-
-#ifdef GP_TIMER_NS
-static const struct timer_gp_dev_cfg_t GP_TIMER_DEV_CFG_NS = {
- .base = MUSCA_TIMER_NS_BASE};
-static struct timer_gp_dev_data_t GP_TIMER_DEV_DATA_NS = {
- .is_initialized = false,
- .alarm0_init = 0,
- .alarm1_init = 0};
-struct timer_gp_dev_t GP_TIMER_DEV_NS = {
- &(GP_TIMER_DEV_CFG_NS),
- &(GP_TIMER_DEV_DATA_NS)};
-#endif
-
-/* PL031 Real-Time Clock structure */
-#ifdef RTC_PL031_S
-static const struct rtc_pl031_dev_cfg_t RTC_PL031_DEV_CFG_S = {
- .base = MUSCA_RTC_S_BASE};
-struct rtc_pl031_dev_t RTC_PL031_DEV_S = {&(RTC_PL031_DEV_CFG_S)};
-#endif
-
-#ifdef RTC_PL031_NS
-static const struct rtc_pl031_dev_cfg_t RTC_PL031_DEV_CFG_NS = {
- .base = MUSCA_RTC_NS_BASE};
-struct rtc_pl031_dev_t RTC_PL031_DEV_NS = {&(RTC_PL031_DEV_CFG_NS)};
-#endif
-
-#ifdef UART0_PL011_S
-static const struct uart_pl011_dev_cfg_t UART0_PL011_DEV_CFG_S = {
- .base = MUSCA_UART0_S_BASE,
- .def_baudrate = DEFAULT_UART_BAUDRATE,
- .def_wlen = UART_PL011_WLEN_8,
- .def_parity = UART_PL011_PARITY_DISABLED,
- .def_stopbit = UART_PL011_STOPBIT_1};
-static struct uart_pl011_dev_data_t UART0_PL011_DEV_DATA_S = {
- .state = UART_PL011_UNINITIALIZED,
- .uart_clk = 0,
- .baudrate = 0};
-struct uart_pl011_dev_t UART0_PL011_DEV_S = {&(UART0_PL011_DEV_CFG_S),
- &(UART0_PL011_DEV_DATA_S)};
-#endif
-
-#ifdef UART0_PL011_NS
-static const struct uart_pl011_dev_cfg_t UART0_PL011_DEV_CFG_NS = {
- .base = MUSCA_UART0_NS_BASE,
- .def_baudrate = DEFAULT_UART_BAUDRATE,
- .def_wlen = UART_PL011_WLEN_8,
- .def_parity = UART_PL011_PARITY_DISABLED,
- .def_stopbit = UART_PL011_STOPBIT_1};
-static struct uart_pl011_dev_data_t UART0_PL011_DEV_DATA_NS = {
- .state = UART_PL011_UNINITIALIZED,
- .uart_clk = 0,
- .baudrate = 0};
-struct uart_pl011_dev_t UART0_PL011_DEV_NS = {&(UART0_PL011_DEV_CFG_NS),
- &(UART0_PL011_DEV_DATA_NS)};
-#endif
-
-#ifdef UART1_PL011_S
-static const struct uart_pl011_dev_cfg_t UART1_PL011_DEV_CFG_S = {
- .base = MUSCA_UART1_S_BASE,
- .def_baudrate = DEFAULT_UART_BAUDRATE,
- .def_wlen = UART_PL011_WLEN_8,
- .def_parity = UART_PL011_PARITY_DISABLED,
- .def_stopbit = UART_PL011_STOPBIT_1};
-static struct uart_pl011_dev_data_t UART1_PL011_DEV_DATA_S = {
- .state = UART_PL011_UNINITIALIZED,
- .uart_clk = 0,
- .baudrate = 0};
-struct uart_pl011_dev_t UART1_PL011_DEV_S = {&(UART1_PL011_DEV_CFG_S),
- &(UART1_PL011_DEV_DATA_S)};
-#endif
-
-#ifdef UART1_PL011_NS
-static const struct uart_pl011_dev_cfg_t UART1_PL011_DEV_CFG_NS = {
- .base = MUSCA_UART1_NS_BASE,
- .def_baudrate = DEFAULT_UART_BAUDRATE,
- .def_wlen = UART_PL011_WLEN_8,
- .def_parity = UART_PL011_PARITY_DISABLED,
- .def_stopbit = UART_PL011_STOPBIT_1};
-static struct uart_pl011_dev_data_t UART1_PL011_DEV_DATA_NS = {
- .state = UART_PL011_UNINITIALIZED,
- .uart_clk = 0,
- .baudrate = 0};
-struct uart_pl011_dev_t UART1_PL011_DEV_NS = {&(UART1_PL011_DEV_CFG_NS),
- &(UART1_PL011_DEV_DATA_NS)};
-#endif
-
-/* SPI IP6524 driver structures */
-#ifdef SPI0_IP6524_S
-static const struct spi_ip6524_dev_cfg_t SPI0_DEV_CFG_S = {
- .base = MUSCA_SPI0_S_BASE};
-static struct spi_ip6524_dev_data_t SPI0_DEV_DATA_S = {
- .state = 0};
-struct spi_ip6524_dev_t SPI0_DEV_S = {&(SPI0_DEV_CFG_S),
- &(SPI0_DEV_DATA_S)};
-#endif
-
-#ifdef SPI0_IP6524_NS
-static const struct spi_ip6524_dev_cfg_t SPI0_DEV_CFG_NS = {
- .base = MUSCA_SPI0_NS_BASE};
-static struct spi_ip6524_dev_data_t SPI0_DEV_DATA_NS = {
- .state = 0};
-struct spi_ip6524_dev_t SPI0_DEV_NS = {&(SPI0_DEV_CFG_NS),
- &(SPI0_DEV_DATA_NS)};
-#endif
-
-/* QSPI IP6514E driver structures */
-#ifdef QSPI_IP6514E_S
-static const struct qspi_ip6514e_dev_cfg_t QSPI_DEV_CFG_S = {
- .base = MUSCA_QSPI_REG_S_BASE,
- /*
- * On Musca-A, only the 18 first address bits are used for any AHB
- * address in a request coming to the QSPI Flash controller.
- * It means that direct accesses are limited to the first 256 KiB of the
- * Flash memory (if the Remap register is not used) and that the Indirect
- * Trigger zone needs to be inside the first 256 KiB as well.
- */
- .addr_mask = (1U << 18) - 1, /* 256 KiB minus 1 byte */
-};
-struct qspi_ip6514e_dev_t QSPI_DEV_S = {
- &QSPI_DEV_CFG_S
-};
-#endif
-
-#ifdef QSPI_IP6514E_NS
-static const struct qspi_ip6514e_dev_cfg_t QSPI_DEV_CFG_NS = {
- .base = MUSCA_QSPI_REG_NS_BASE,
- /*
- * On Musca-A, only the 18 first address bits are used for any AHB
- * address in a request coming to the QSPI Flash controller.
- * It means that direct accesses are limited to the first 256 KiB of the
- * Flash memory (if the Remap register is not used) and that the Indirect
- * Trigger zone needs to be inside the first 256 KiB as well.
- */
- .addr_mask = (1U << 18) - 1, /* 256 KiB minus 1 byte */
-};
-struct qspi_ip6514e_dev_t QSPI_DEV_NS = {
- &QSPI_DEV_CFG_NS
-};
-#endif
-
-/* ======= External peripheral configuration structure definitions ======= */
-
-/* MT25QL Flash memory library structures */
-#if (defined(MT25QL_S) && defined(QSPI_IP6514E_S))
-struct mt25ql_dev_t MT25QL_DEV_S = {
- .controller = &QSPI_DEV_S,
- .direct_access_start_addr = MUSCA_QSPI_FLASH_S_BASE,
- .baud_rate_div = 4U,
- /*
- * 8 MiB flash memory are advertised in the Arm Musca-A Test Chip and Board
- * Technical Reference Manual. The MT25QL Flash device may however contain
- * more.
- */
- .size = 0x00800000U, /* 8 MiB */
- .config_state = { MT25QL_FUNC_STATE_NOT_INITED },
-};
-#endif
-
-#if (defined(MT25QL_NS) && defined(QSPI_IP6514E_NS))
-struct mt25ql_dev_t MT25QL_DEV_NS
- = {
- .controller = &QSPI_DEV_NS,
- .direct_access_start_addr = MUSCA_QSPI_FLASH_NS_BASE,
- .baud_rate_div = 4U,
- /*
- * 8 MiB flash memory are advertised in the Arm Musca-A Test Chip and Board
- * Technical Reference Manual. The MT25QL Flash device may however contain
- * more.
- */
- .size = 0x00800000U, /* 8 MiB */
- .config_state = { MT25QL_FUNC_STATE_NOT_INITED },
-};
-#endif
diff --git a/platform/ext/target/musca_a/Device/Source/gcc/musca_bl2.ld b/platform/ext/target/musca_a/Device/Source/gcc/musca_bl2.ld
deleted file mode 100644
index c792fff..0000000
--- a/platform/ext/target/musca_a/Device/Source/gcc/musca_bl2.ld
+++ /dev/null
@@ -1,219 +0,0 @@
-;/*
-; * Copyright (c) 2018-2019 Arm Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; *
-; *
-; * This file is derivative of CMSIS V5.00 gcc_arm.ld
-; */
-
-/* Linker script to configure memory regions. */
-/* This file will be run trough the pre-processor. */
-
-#include "region_defs.h"
-
-MEMORY
-{
- FLASH (rx) : ORIGIN = BL2_CODE_START, LENGTH = BL2_CODE_SIZE
- CODE_RAM (rx) : ORIGIN = BL2_CODE_SRAM_EXEC_BASE, LENGTH = BL2_CODE_SIZE
- RAM (rwx) : ORIGIN = BL2_DATA_START, LENGTH = BL2_DATA_SIZE
-}
-
-__heap_size__ = BL2_HEAP_SIZE;
-__msp_stack_size__ = BL2_MSP_STACK_SIZE;
-
-/* Library configurations */
-GROUP(libgcc.a libc.a libm.a libnosys.a)
-
-ENTRY(Reset_Handler)
-
-SECTIONS
-{
- /* Startup section is loaded to Flash and runs from Flash */
- .startup :
- {
- KEEP(*(.vectors))
- __Vectors_End = .;
- __Vectors_Size = __Vectors_End - __Vectors;
- __end__ = .;
-
- KEEP(*(.init))
- KEEP(*(.fini))
-
- *startup_cmsdk_musca_bl2.*
- } > FLASH
-
- .text :
- {
- KEEP(*(.vectors))
- __Vectors_End = .;
- __Vectors_Size = __Vectors_End - __Vectors;
- __end__ = .;
-
- *(.text*)
-
- KEEP(*(.init))
- KEEP(*(.fini))
-
-
- /* .ctors */
- *crtbegin.o(.ctors)
- *crtbegin?.o(.ctors)
- *(EXCLUDE_FILE(*crtend?.o *crtend.o) .ctors)
- *(SORT(.ctors.*))
- *(.ctors)
-
- /* .dtors */
- *crtbegin.o(.dtors)
- *crtbegin?.o(.dtors)
- *(EXCLUDE_FILE(*crtend?.o *crtend.o) .dtors)
- *(SORT(.dtors.*))
- *(.dtors)
-
- *(.rodata*)
-
- KEEP(*(.eh_frame*))
- . = ALIGN(4); /* This alignment is needed to make the section size 4 bytes aligned */
- } > CODE_RAM AT > FLASH
-
- /* Create same symbols that armclang does so that in the c files
- * we do not have to deal with the compiler type
- */
- Image$$ER_CODE_SRAM$$Base = ADDR(.text);
- Image$$ER_CODE_SRAM$$Limit = .;
- Image$$ER_CODE_SRAM$$Length = Image$$ER_CODE_SRAM$$Limit - Image$$ER_CODE_SRAM$$Base;
- Load$$ER_CODE_SRAM$$Base = LOADADDR(.text);
- Load$$ER_CODE_SRAM$$Length = Image$$ER_CODE_SRAM$$Length;
- Load$$ER_CODE_SRAM$$Limit = Load$$ER_CODE_SRAM$$Base + Load$$ER_CODE_SRAM$$Length;
-
- .ARM.extab :
- {
- *(.ARM.extab* .gnu.linkonce.armextab.*)
- } > FLASH
-
- __exidx_start = .;
- .ARM.exidx :
- {
- *(.ARM.exidx* .gnu.linkonce.armexidx.*)
- } > FLASH
- __exidx_end = .;
-
- /* To copy multiple ROM to RAM sections,
- * define etext2/data2_start/data2_end and
- * define __STARTUP_COPY_MULTIPLE in startup_cmsdk_musca_bl2.S */
- .copy.table :
- {
- . = ALIGN(4);
- __copy_table_start__ = .;
- LONG (__etext)
- LONG (__data_start__)
- LONG (__data_end__ - __data_start__)
- LONG (Load$$ER_CODE_SRAM$$Base)
- LONG (Image$$ER_CODE_SRAM$$Base)
- LONG (Image$$ER_CODE_SRAM$$Length)
- LONG (DEFINED(__etext2) ? __etext2 : 0)
- LONG (DEFINED(__data2_start__) ? __data2_start__ : 0)
- LONG (DEFINED(__data2_start__) ? __data2_end__ - __data2_start__ : 0)
- __copy_table_end__ = .;
- } > FLASH
-
- /* To clear multiple BSS sections,
- * uncomment .zero.table section and,
- * define __STARTUP_CLEAR_BSS_MULTIPLE in startup_cmsdk_musca_bl2.S */
- .zero.table :
- {
- . = ALIGN(4);
- __zero_table_start__ = .;
- LONG (__bss_start__)
- LONG (__bss_end__ - __bss_start__)
- LONG (DEFINED(__bss2_start__) ? __bss2_start__ : 0)
- LONG (DEFINED(__bss2_start__) ? __bss2_end__ - __bss2_start__ : 0)
- __zero_table_end__ = .;
- } > FLASH
-
- __etext = .;
-
- .tfm_bl2_shared_data : ALIGN(32)
- {
- . += BOOT_TFM_SHARED_DATA_SIZE;
- } > RAM
- Image$$SHARED_DATA$$RW$$Base = ADDR(.tfm_bl2_shared_data);
- Image$$SHARED_DATA$$RW$$Limit = ADDR(.tfm_bl2_shared_data) + SIZEOF(.tfm_bl2_shared_data);
-
- .data : AT (__etext)
- {
- __data_start__ = .;
- *(vtable)
- *(.data*)
-
- . = ALIGN(4);
- /* preinit data */
- PROVIDE_HIDDEN (__preinit_array_start = .);
- KEEP(*(.preinit_array))
- PROVIDE_HIDDEN (__preinit_array_end = .);
-
- . = ALIGN(4);
- /* init data */
- PROVIDE_HIDDEN (__init_array_start = .);
- KEEP(*(SORT(.init_array.*)))
- KEEP(*(.init_array))
- PROVIDE_HIDDEN (__init_array_end = .);
-
-
- . = ALIGN(4);
- /* finit data */
- PROVIDE_HIDDEN (__fini_array_start = .);
- KEEP(*(SORT(.fini_array.*)))
- KEEP(*(.fini_array))
- PROVIDE_HIDDEN (__fini_array_end = .);
-
- KEEP(*(.jcr*))
- . = ALIGN(4);
- /* All data end */
- __data_end__ = .;
-
- } > RAM
- Image$$ER_DATA$$Base = ADDR(.data);
-
- .bss :
- {
- . = ALIGN(4);
- __bss_start__ = .;
- *(.bss*)
- *(COMMON)
- . = ALIGN(4);
- __bss_end__ = .;
- } > RAM
-
- bss_size = __bss_end__ - __bss_start__;
-
- .msp_stack : ALIGN(32)
- {
- . += __msp_stack_size__;
- } > RAM
- Image$$ARM_LIB_STACK$$ZI$$Base = ADDR(.msp_stack);
- Image$$ARM_LIB_STACK$$ZI$$Limit = ADDR(.msp_stack) + SIZEOF(.msp_stack);
-
- .heap : ALIGN(8)
- {
- __end__ = .;
- PROVIDE(end = .);
- __HeapBase = .;
- . += __heap_size__;
- __HeapLimit = .;
- __heap_limit = .; /* Add for _sbrk */
- } > RAM
- Image$$ARM_LIB_HEAP$$ZI$$Limit = ADDR(.heap) + SIZEOF(.heap);
-
- PROVIDE(__stack = Image$$ARM_LIB_STACK$$ZI$$Limit);
-}
diff --git a/platform/ext/target/musca_a/Device/Source/gcc/musca_ns.ld b/platform/ext/target/musca_a/Device/Source/gcc/musca_ns.ld
deleted file mode 100644
index bc81a6b..0000000
--- a/platform/ext/target/musca_a/Device/Source/gcc/musca_ns.ld
+++ /dev/null
@@ -1,189 +0,0 @@
-;/*
-; * Copyright (c) 2018 ARM Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; *
-; *
-; * This file is derivative of CMSIS V5.00 gcc_arm.ld
-; */
-
-/* Linker script to configure memory regions. */
-/* This file will be run trough the pre-processor. */
-
-#include "region_defs.h"
-
-MEMORY
-{
- FLASH (rx) : ORIGIN = NS_CODE_START, LENGTH = NS_CODE_SIZE
- RAM (rwx) : ORIGIN = NS_DATA_START, LENGTH = NS_DATA_SIZE
-}
-
-__heap_size__ = NS_HEAP_SIZE;
-__psp_stack_size__ = NS_PSP_STACK_SIZE;
-__msp_stack_size__ = NS_MSP_STACK_SIZE;
-
-/* Library configurations */
-GROUP(libgcc.a libc.a libm.a libnosys.a)
-
-ENTRY(Reset_Handler)
-
-SECTIONS
-{
- .text :
- {
- KEEP(*(.vectors))
- __Vectors_End = .;
- __Vectors_Size = __Vectors_End - __Vectors;
- __end__ = .;
-
- *(.text*)
-
- KEEP(*(.init))
- KEEP(*(.fini))
-
-
- /* .ctors */
- *crtbegin.o(.ctors)
- *crtbegin?.o(.ctors)
- *(EXCLUDE_FILE(*crtend?.o *crtend.o) .ctors)
- *(SORT(.ctors.*))
- *(.ctors)
-
- /* .dtors */
- *crtbegin.o(.dtors)
- *crtbegin?.o(.dtors)
- *(EXCLUDE_FILE(*crtend?.o *crtend.o) .dtors)
- *(SORT(.dtors.*))
- *(.dtors)
-
- *(.rodata*)
-
- KEEP(*(.eh_frame*))
- } > FLASH
-
- .ARM.extab :
- {
- *(.ARM.extab* .gnu.linkonce.armextab.*)
- } > FLASH
-
- __exidx_start = .;
- .ARM.exidx :
- {
- *(.ARM.exidx* .gnu.linkonce.armexidx.*)
- } > FLASH
- __exidx_end = .;
-
- /* To copy multiple ROM to RAM sections,
- * define etext2/data2_start/data2_end and
- * define __STARTUP_COPY_MULTIPLE in startup_cmsdk_musca_ns.S */
- .copy.table :
- {
- . = ALIGN(4);
- __copy_table_start__ = .;
- LONG (__etext)
- LONG (__data_start__)
- LONG (__data_end__ - __data_start__)
- LONG (DEFINED(__etext2) ? __etext2 : 0)
- LONG (DEFINED(__data2_start__) ? __data2_start__ : 0)
- LONG (DEFINED(__data2_start__) ? __data2_end__ - __data2_start__ : 0)
- __copy_table_end__ = .;
- } > FLASH
-
- /* To clear multiple BSS sections,
- * uncomment .zero.table section and,
- * define __STARTUP_CLEAR_BSS_MULTIPLE in startup_cmsdk_musca_ns.S */
- .zero.table :
- {
- . = ALIGN(4);
- __zero_table_start__ = .;
- LONG (__bss_start__)
- LONG (__bss_end__ - __bss_start__)
- LONG (DEFINED(__bss2_start__) ? __bss2_start__ : 0)
- LONG (DEFINED(__bss2_start__) ? __bss2_end__ - __bss2_start__ : 0)
- __zero_table_end__ = .;
- } > FLASH
-
- __etext = .;
-
- .data : AT (__etext)
- {
- __data_start__ = .;
- *(vtable)
- *(.data*)
-
- . = ALIGN(4);
- /* preinit data */
- PROVIDE_HIDDEN (__preinit_array_start = .);
- KEEP(*(.preinit_array))
- PROVIDE_HIDDEN (__preinit_array_end = .);
-
- . = ALIGN(4);
- /* init data */
- PROVIDE_HIDDEN (__init_array_start = .);
- KEEP(*(SORT(.init_array.*)))
- KEEP(*(.init_array))
- PROVIDE_HIDDEN (__init_array_end = .);
-
-
- . = ALIGN(4);
- /* finit data */
- PROVIDE_HIDDEN (__fini_array_start = .);
- KEEP(*(SORT(.fini_array.*)))
- KEEP(*(.fini_array))
- PROVIDE_HIDDEN (__fini_array_end = .);
-
- KEEP(*(.jcr*))
- . = ALIGN(4);
- /* All data end */
- __data_end__ = .;
-
- } > RAM
-
- .bss :
- {
- . = ALIGN(4);
- __bss_start__ = .;
- *(.bss*)
- *(COMMON)
- . = ALIGN(4);
- __bss_end__ = .;
- } > RAM
-
- bss_size = __bss_end__ - __bss_start__;
-
- .msp_stack : ALIGN(32)
- {
- . += __msp_stack_size__;
- } > RAM
- Image$$ARM_LIB_STACK_MSP$$ZI$$Base = ADDR(.msp_stack);
- Image$$ARM_LIB_STACK_MSP$$ZI$$Limit = ADDR(.msp_stack) + SIZEOF(.msp_stack);
-
- .psp_stack : ALIGN(32)
- {
- . += __psp_stack_size__;
- } > RAM
- Image$$ARM_LIB_STACK$$ZI$$Base = ADDR(.psp_stack);
- Image$$ARM_LIB_STACK$$ZI$$Limit = ADDR(.psp_stack) + SIZEOF(.psp_stack);
-
- .heap : ALIGN(8)
- {
- __end__ = .;
- PROVIDE(end = .);
- __HeapBase = .;
- . += __heap_size__;
- __HeapLimit = .;
- __heap_limit = .; /* Add for _sbrk */
- } > RAM
-
- PROVIDE(__stack = Image$$ARM_LIB_STACK$$ZI$$Limit);
-}
diff --git a/platform/ext/target/musca_a/Device/Source/gcc/startup_cmsdk_musca_bl2.S b/platform/ext/target/musca_a/Device/Source/gcc/startup_cmsdk_musca_bl2.S
deleted file mode 100644
index 82a57b2..0000000
--- a/platform/ext/target/musca_a/Device/Source/gcc/startup_cmsdk_musca_bl2.S
+++ /dev/null
@@ -1,366 +0,0 @@
-;/*
-; * Copyright (c) 2009-2020 ARM Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; *
-; *
-; * This file is derivative of CMSIS V5.00 startup_ARMCM33.S
-; */
-
-#include "tfm_plat_config.h"
-
- .syntax unified
- .arch armv8-m.main
-
- .section .vectors
- .align 2
- .globl __Vectors
-__Vectors:
- .long Image$$ARM_LIB_STACK$$ZI$$Limit /* Top of Stack */
- .long Reset_Handler /* Reset Handler */
- .long NMI_Handler /* NMI Handler */
- .long HardFault_Handler /* Hard Fault Handler */
- .long MemManage_Handler /* MPU Fault Handler */
- .long BusFault_Handler /* Bus Fault Handler */
- .long UsageFault_Handler /* Usage Fault Handler */
- .long SecureFault_Handler /* Secure Fault Handler */
- .long 0 /* Reserved */
- .long 0 /* Reserved */
- .long 0 /* Reserved */
- .long SVC_Handler /* SVCall Handler */
- .long DebugMon_Handler /* Debug Monitor Handler */
- .long 0 /* Reserved */
- .long PendSV_Handler /* PendSV Handler */
- .long SysTick_Handler /* SysTick Handler */
-
- /* Core interrupts */
- .long NS_WATCHDOG_RESET_IRQHandler /* 0: Non-Secure Watchdog Reset Request Interrupt */
- .long NS_WATCHDOG_IRQHandler /* 1: Non-Secure Watchdog Interrupt */
- .long S32K_TIMER_IRQHandler /* 2: S32K Timer Interrupt */
- .long TIMER0_IRQHandler /* 3: CMSDK Timer 0 Interrupt */
- .long TIMER1_IRQHandler /* 4: CMSDK Timer 1 Interrupt */
- .long DUALTIMER_IRQHandler /* 5: CMSDK Dual Timer Interrupt */
- .long MHU0_IRQHandler /* 6: Message Handling Unit 0 Interrupt */
- .long MHU1_IRQHandler /* 7: Message Handling Unit 1 Interrupt */
- .long CRYPTOCELL_IRQHandler /* 8: CryptoCell-312 Interrupt */
- .long MPC_Handler /* 9: Secure Combined MPC Interrupt */
- .long PPC_Handler /* 10: Secure Combined PPC Interrupt */
- .long S_MSC_COMBINED_IRQHandler /* 11: Secure Combined MSC Interrupt */
- .long S_BRIDGE_ERR_IRQHandler /* 12: Secure Bridge Error Combined Interrupt */
- .long I_CACHE_INV_ERR_IRQHandler /* 13: Intsruction Cache Invalidation Interrupt */
- .long 0 /* 14: Reserved */
- .long SYS_PPU_IRQHandler /* 15: System PPU Interrupt */
- .long CPU0_PPU_IRQHandler /* 16: CPU0 PPU Interrupt */
- .long CPU1_PPU_IRQHandler /* 17: CPU1 PPU Interrupt */
- .long CPU0_DGB_PPU_IRQHandler /* 18: CPU0 Debug PPU Interrupt */
- .long CPU1_DGB_PPU_IRQHandler /* 19: CPU1 Debug PPU Interrupt */
- .long CRYPTOCELL_PPU_IRQHandler /* 20: CryptoCell PPU Interrupt */
- .long 0 /* 21: Reserved */
- .long RAM0_PPU_IRQHandler /* 22: RAM 0 PPU Interrupt */
- .long RAM1_PPU_IRQHandler /* 23: RAM 1 PPU Interrupt */
- .long RAM2_PPU_IRQHandler /* 24: RAM 2 PPU Interrupt */
- .long RAM3_PPU_IRQHandler /* 25: RAM 3 PPU Interrupt */
- .long DEBUG_PPU_IRQHandler /* 26: Debug PPU Interrupt */
- .long 0 /* 27: Reserved */
- .long CPU0_CTI_IRQHandler /* 28: CPU0 CTI Interrupt */
- .long CPU1_CTI_IRQHandler /* 29: CPU1 CTI Interrupt */
- .long 0 /* 30: Reserved */
- .long 0 /* 31: Reserved */
-
- /* External interrupts */
- .long 0 /* 32: Reserved */
- .long GpTimer_IRQHandler /* 33: General Purpose Timer */
- .long I2C0_IRQHandler /* 34: I2C0 */
- .long I2C1_IRQHandler /* 35: I2C1 */
- .long I2S_IRQHandler /* 36: I2S */
- .long SPI_IRQHandler /* 37: SPI */
- .long QSPI_IRQHandler /* 38: QSPI */
- .long UARTRX0_Handler /* 39: UART0 receive FIFO interrupt */
- .long UARTTX0_Handler /* 40: UART0 transmit FIFO interrupt */
- .long UART0_RxTimeout_IRQHandler /* 41: UART0 receive timeout interrupt */
- .long UART0_ModemStatus_IRQHandler /* 42: UART0 modem status interrupt */
- .long UART0_Error_IRQHandler /* 43: UART0 error interrupt */
- .long UART0_IRQHandler /* 44: UART0 interrupt */
- .long UARTRX1_Handler /* 45: UART0 receive FIFO interrupt */
- .long UARTTX1_Handler /* 46: UART0 transmit FIFO interrupt */
- .long UART1_RxTimeout_IRQHandler /* 47: UART0 receive timeout interrupt */
- .long UART1_ModemStatus_IRQHandler /* 48: UART0 modem status interrupt */
- .long UART1_Error_IRQHandler /* 49: UART0 error interrupt */
- .long UART1_IRQHandler /* 50: UART0 interrupt */
- .long GPIO_0_IRQHandler /* 51: GPIO 0 interrupt */
- .long GPIO_1_IRQHandler /* 52: GPIO 1 interrupt */
- .long GPIO_2_IRQHandler /* 53: GPIO 2 interrupt */
- .long GPIO_3_IRQHandler /* 54: GPIO 3 interrupt */
- .long GPIO_4_IRQHandler /* 55: GPIO 4 interrupt */
- .long GPIO_5_IRQHandler /* 56: GPIO 5 interrupt */
- .long GPIO_6_IRQHandler /* 57: GPIO 6 interrupt */
- .long GPIO_7_IRQHandler /* 58: GPIO 7 interrupt */
- .long GPIO_8_IRQHandler /* 59: GPIO 8 interrupt */
- .long GPIO_9_IRQHandler /* 60: GPIO 9 interrupt */
- .long GPIO_10_IRQHandler /* 61: GPIO 10 interrupt */
- .long GPIO_11_IRQHandler /* 62: GPIO 11 interrupt */
- .long GPIO_12_IRQHandler /* 63: GPIO 12 interrupt */
- .long GPIO_13_IRQHandler /* 64: GPIO 13 interrupt */
- .long GPIO_14_IRQHandler /* 65: GPIO 14 interrupt */
- .long GPIO_15_IRQHandler /* 66: GPIO 15 interrupt */
- .long Combined_IRQHandler /* 67: Combined interrupt */
- .long PVT_IRQHandler /* 68: PVT sensor interrupt */
- .long 0 /* 69: Reserved */
- .long PWM_0_IRQHandler /* 70: PWM0 interrupt */
- .long RTC_IRQHandler /* 71: RTC interrupt */
- .long GpTimer0_IRQHandler /* 72: General Purpose Timer0 */
- .long GpTimer1_IRQHandler /* 73: General Purpose Timer1 */
- .long PWM_1_IRQHandler /* 74: PWM1 interrupt */
- .long PWM_2_IRQHandler /* 75: PWM2 interrupt */
- .long IOMUX_IRQHandler /* 76: IOMUX interrupt */
-
- .size __Vectors, . - __Vectors
-
- .text
- .thumb
- .thumb_func
- .align 2
- .globl Reset_Handler
- .type Reset_Handler, %function
-Reset_Handler:
-/* Firstly it copies data from read only memory to RAM. There are two schemes
- * to copy. One can copy more than one sections. Another can only copy
- * one section. The former scheme needs more instructions and read-only
- * data to implement than the latter.
- * Macro __STARTUP_COPY_MULTIPLE is used to choose between two schemes. */
-
- /* Only run on core 0 */
- mov r0, #0x50000000
- add r0, #0x0001F000
- ldr r0, [r0]
- cmp r0,#0
-not_the_core_to_run_on:
- bne not_the_core_to_run_on
-
-#ifdef __STARTUP_COPY_MULTIPLE
-/* Multiple sections scheme.
- *
- * Between symbol address __copy_table_start__ and __copy_table_end__,
- * there are array of triplets, each of which specify:
- * offset 0: LMA of start of a section to copy from
- * offset 4: VMA of start of a section to copy to
- * offset 8: size of the section to copy. Must be multiply of 4
- *
- * All addresses must be aligned to 4 bytes boundary.
- */
- ldr r4, =__copy_table_start__
- ldr r5, =__copy_table_end__
-
-.L_loop0:
- cmp r4, r5
- bge .L_loop0_done
- ldr r1, [r4]
- ldr r2, [r4, #4]
- ldr r3, [r4, #8]
-
-.L_loop0_0:
- subs r3, #4
- ittt ge
- ldrge r0, [r1, r3]
- strge r0, [r2, r3]
- bge .L_loop0_0
-
- adds r4, #12
- b .L_loop0
-
-.L_loop0_done:
-#else
-/* Single section scheme.
- *
- * The ranges of copy from/to are specified by following symbols
- * __etext: LMA of start of the section to copy from. Usually end of text
- * __data_start__: VMA of start of the section to copy to
- * __data_end__: VMA of end of the section to copy to
- *
- * All addresses must be aligned to 4 bytes boundary.
- */
- ldr r1, =__etext
- ldr r2, =__data_start__
- ldr r3, =__data_end__
-
-.L_loop1:
- cmp r2, r3
- ittt lt
- ldrlt r0, [r1], #4
- strlt r0, [r2], #4
- blt .L_loop1
-#endif /*__STARTUP_COPY_MULTIPLE */
-
-/* This part of work usually is done in C library startup code. Otherwise,
- * define this macro to enable it in this startup.
- *
- * There are two schemes too. One can clear multiple BSS sections. Another
- * can only clear one section. The former is more size expensive than the
- * latter.
- *
- * Define macro __STARTUP_CLEAR_BSS_MULTIPLE to choose the former.
- * Otherwise efine macro __STARTUP_CLEAR_BSS to choose the later.
- */
-#ifdef __STARTUP_CLEAR_BSS_MULTIPLE
-/* Multiple sections scheme.
- *
- * Between symbol address __copy_table_start__ and __copy_table_end__,
- * there are array of tuples specifying:
- * offset 0: Start of a BSS section
- * offset 4: Size of this BSS section. Must be multiply of 4
- */
- ldr r3, =__zero_table_start__
- ldr r4, =__zero_table_end__
-
-.L_loop2:
- cmp r3, r4
- bge .L_loop2_done
- ldr r1, [r3]
- ldr r2, [r3, #4]
- movs r0, 0
-
-.L_loop2_0:
- subs r2, #4
- itt ge
- strge r0, [r1, r2]
- bge .L_loop2_0
-
- adds r3, #8
- b .L_loop2
-.L_loop2_done:
-#elif defined (__STARTUP_CLEAR_BSS)
-/* Single BSS section scheme.
- *
- * The BSS section is specified by following symbols
- * __bss_start__: start of the BSS section.
- * __bss_end__: end of the BSS section.
- *
- * Both addresses must be aligned to 4 bytes boundary.
- */
- ldr r1, =__bss_start__
- ldr r2, =__bss_end__
-
- movs r0, 0
-.L_loop3:
- cmp r1, r2
- itt lt
- strlt r0, [r1], #4
- blt .L_loop3
-#endif /* __STARTUP_CLEAR_BSS_MULTIPLE || __STARTUP_CLEAR_BSS */
-
- bl SystemInit
-
-#ifndef __START
-#define __START _start
-#endif
- bl __START
-
- .pool
- .size Reset_Handler, . - Reset_Handler
-
-
-/* Macro to define default handlers. */
- .macro def_irq_handler handler_name
- .align 1
- .thumb_func
- .weak \handler_name
- \handler_name:
- b \handler_name
- .endm
-
- def_irq_handler NMI_Handler
- def_irq_handler HardFault_Handler
- def_irq_handler MemManage_Handler
- def_irq_handler BusFault_Handler
- def_irq_handler UsageFault_Handler
- def_irq_handler SecureFault_Handler
- def_irq_handler SVC_Handler
- def_irq_handler DebugMon_Handler
- def_irq_handler PendSV_Handler
- def_irq_handler SysTick_Handler
-
- /* Core interrupts */
- def_irq_handler NS_WATCHDOG_RESET_IRQHandler /* 0: Non-Secure Watchdog Reset Request Interrupt */
- def_irq_handler NS_WATCHDOG_IRQHandler /* 1: Non-Secure Watchdog Interrupt */
- def_irq_handler S32K_TIMER_IRQHandler /* 2: S32K Timer Interrupt */
- def_irq_handler TIMER0_IRQHandler /* 3: CMSDK Timer 0 Interrupt */
- def_irq_handler TIMER1_IRQHandler /* 4: CMSDK Timer 1 Interrupt */
- def_irq_handler DUALTIMER_IRQHandler /* 5: CMSDK Dual Timer Interrupt */
- def_irq_handler MHU0_IRQHandler /* 6: Message Handling Unit 0 Interrupt */
- def_irq_handler MHU1_IRQHandler /* 7: Message Handling Unit 1 Interrupt */
- def_irq_handler CRYPTOCELL_IRQHandler /* 8: CryptoCell-312 Interrupt */
- def_irq_handler MPC_Handler /* 9: Secure Combined MPC Interrupt */
- def_irq_handler PPC_Handler /* 10: Secure Combined PPC Interrupt */
- def_irq_handler S_MSC_COMBINED_IRQHandler /* 11: Secure Combined MSC Interrupt */
- def_irq_handler S_BRIDGE_ERR_IRQHandler /* 12: Secure Bridge Error Combined Interrupt */
- def_irq_handler I_CACHE_INV_ERR_IRQHandler /* 13: Intsruction Cache Invalidation Interrupt */
- def_irq_handler SYS_PPU_IRQHandler /* 15: System PPU Interrupt */
- def_irq_handler CPU0_PPU_IRQHandler /* 16: CPU0 PPU Interrupt */
- def_irq_handler CPU1_PPU_IRQHandler /* 17: CPU1 PPU Interrupt */
- def_irq_handler CPU0_DGB_PPU_IRQHandler /* 18: CPU0 Debug PPU Interrupt */
- def_irq_handler CPU1_DGB_PPU_IRQHandler /* 19: CPU1 Debug PPU Interrupt */
- def_irq_handler CRYPTOCELL_PPU_IRQHandler /* 20: CryptoCell PPU Interrupt */
- def_irq_handler RAM0_PPU_IRQHandler /* 22: RAM 0 PPU Interrupt */
- def_irq_handler RAM1_PPU_IRQHandler /* 23: RAM 1 PPU Interrupt */
- def_irq_handler RAM2_PPU_IRQHandler /* 24: RAM 2 PPU Interrupt */
- def_irq_handler RAM3_PPU_IRQHandler /* 25: RAM 3 PPU Interrupt */
- def_irq_handler DEBUG_PPU_IRQHandler /* 26: Debug PPU Interrupt */
- def_irq_handler CPU0_CTI_IRQHandler /* 28: CPU0 CTI Interrupt */
- def_irq_handler CPU1_CTI_IRQHandler /* 29: CPU1 CTI Interrupt */
-
- /* External interrupts */
- def_irq_handler GpTimer_IRQHandler /* 33: General Purpose Timer */
- def_irq_handler I2C0_IRQHandler /* 34: I2C0 */
- def_irq_handler I2C1_IRQHandler /* 35: I2C1 */
- def_irq_handler I2S_IRQHandler /* 36: I2S */
- def_irq_handler SPI_IRQHandler /* 37: SPI */
- def_irq_handler QSPI_IRQHandler /* 38: QSPI */
- def_irq_handler UARTRX0_Handler /* 39: UART0 receive FIFO interrupt */
- def_irq_handler UARTTX0_Handler /* 40: UART0 transmit FIFO interrupt */
- def_irq_handler UART0_RxTimeout_IRQHandler /* 41: UART0 receive timeout interrupt */
- def_irq_handler UART0_ModemStatus_IRQHandler /* 42: UART0 modem status interrupt */
- def_irq_handler UART0_Error_IRQHandler /* 43: UART0 error interrupt */
- def_irq_handler UART0_IRQHandler /* 44: UART0 interrupt */
- def_irq_handler UARTRX1_Handler /* 45: UART0 receive FIFO interrupt */
- def_irq_handler UARTTX1_Handler /* 46: UART0 transmit FIFO interrupt */
- def_irq_handler UART1_RxTimeout_IRQHandler /* 47: UART0 receive timeout interrupt */
- def_irq_handler UART1_ModemStatus_IRQHandler /* 48: UART0 modem status interrupt */
- def_irq_handler UART1_Error_IRQHandler /* 49: UART0 error interrupt */
- def_irq_handler UART1_IRQHandler /* 50: UART0 interrupt */
- def_irq_handler GPIO_0_IRQHandler /* 51: GPIO 0 interrupt */
- def_irq_handler GPIO_1_IRQHandler /* 52: GPIO 1 interrupt */
- def_irq_handler GPIO_2_IRQHandler /* 53: GPIO 2 interrupt */
- def_irq_handler GPIO_3_IRQHandler /* 54: GPIO 3 interrupt */
- def_irq_handler GPIO_4_IRQHandler /* 55: GPIO 4 interrupt */
- def_irq_handler GPIO_5_IRQHandler /* 56: GPIO 5 interrupt */
- def_irq_handler GPIO_6_IRQHandler /* 57: GPIO 6 interrupt */
- def_irq_handler GPIO_7_IRQHandler /* 58: GPIO 7 interrupt */
- def_irq_handler GPIO_8_IRQHandler /* 59: GPIO 8 interrupt */
- def_irq_handler GPIO_9_IRQHandler /* 60: GPIO 9 interrupt */
- def_irq_handler GPIO_10_IRQHandler /* 61: GPIO 10 interrupt */
- def_irq_handler GPIO_11_IRQHandler /* 62: GPIO 11 interrupt */
- def_irq_handler GPIO_12_IRQHandler /* 63: GPIO 12 interrupt */
- def_irq_handler GPIO_13_IRQHandler /* 64: GPIO 13 interrupt */
- def_irq_handler GPIO_14_IRQHandler /* 65: GPIO 14 interrupt */
- def_irq_handler GPIO_15_IRQHandler /* 66: GPIO 15 interrupt */
- def_irq_handler Combined_IRQHandler /* 67: Combined interrupt */
- def_irq_handler PVT_IRQHandler /* 68: PVT sensor interrupt */
- def_irq_handler PWM_0_IRQHandler /* 70: PWM0 interrupt */
- def_irq_handler RTC_IRQHandler /* 71: RTC interrupt */
- def_irq_handler GpTimer0_IRQHandler /* 72: General Purpose Timer0 */
- def_irq_handler GpTimer1_IRQHandler /* 73: General Purpose Timer1 */
- def_irq_handler PWM_1_IRQHandler /* 74: PWM1 interrupt */
- def_irq_handler PWM_2_IRQHandler /* 75: PWM2 interrupt */
- def_irq_handler IOMUX_IRQHandler /* 76: IOMUX interrupt */
-
- .end
diff --git a/platform/ext/target/musca_a/Device/Source/gcc/startup_cmsdk_musca_ns.S b/platform/ext/target/musca_a/Device/Source/gcc/startup_cmsdk_musca_ns.S
deleted file mode 100644
index b60421c..0000000
--- a/platform/ext/target/musca_a/Device/Source/gcc/startup_cmsdk_musca_ns.S
+++ /dev/null
@@ -1,355 +0,0 @@
-;/*
-; * Copyright (c) 2009-2020 ARM Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; *
-; *
-; * This file is derivative of CMSIS V5.00 startup_ARMCM33.S
-; */
-
- .syntax unified
- .arch armv8-m.main
-
- .section .vectors
- .align 2
- .globl __Vectors
-__Vectors:
- .long Image$$ARM_LIB_STACK_MSP$$ZI$$Limit /* Top of Stack */
- .long Reset_Handler /* Reset Handler */
- .long NMI_Handler /* NMI Handler */
- .long HardFault_Handler /* Hard Fault Handler */
- .long MemManage_Handler /* MPU Fault Handler */
- .long BusFault_Handler /* Bus Fault Handler */
- .long UsageFault_Handler /* Usage Fault Handler */
- .long 0 /* Reserved */
- .long 0 /* Reserved */
- .long 0 /* Reserved */
- .long 0 /* Reserved */
- .long SVC_Handler /* SVCall Handler */
- .long DebugMon_Handler /* Debug Monitor Handler */
- .long 0 /* Reserved */
- .long PendSV_Handler /* PendSV Handler */
- .long SysTick_Handler /* SysTick Handler */
-
- /* Core interrupts */
- .long NS_WATCHDOG_RESET_IRQHandler /* 0: Non-Secure Watchdog Reset Request Interrupt */
- .long NS_WATCHDOG_IRQHandler /* 1: Non-Secure Watchdog Interrupt */
- .long S32K_TIMER_IRQHandler /* 2: S32K Timer Interrupt */
- .long TIMER0_IRQHandler /* 3: CMSDK Timer 0 Interrupt */
- .long TIMER1_Handler /* 4: CMSDK Timer 1 Interrupt */
- .long DUALTIMER_IRQHandler /* 5: CMSDK Dual Timer Interrupt */
- .long MHU0_IRQHandler /* 6: Message Handling Unit 0 Interrupt */
- .long MHU1_IRQHandler /* 7: Message Handling Unit 1 Interrupt */
- .long CRYPTOCELL_IRQHandler /* 8: CryptoCell-312 Interrupt */
- .long 0 /* 9: Reserved */
- .long 0 /* 10: Reserved */
- .long 0 /* 11: Reserved */
- .long 0 /* 12: Reserved */
- .long I_CACHE_INV_ERR_IRQHandler /* 13: Intsruction Cache Invalidation Interrupt */
- .long 0 /* 14: Reserved */
- .long SYS_PPU_IRQHandler /* 15: System PPU Interrupt */
- .long CPU0_PPU_IRQHandler /* 16: CPU0 PPU Interrupt */
- .long CPU1_PPU_IRQHandler /* 17: CPU1 PPU Interrupt */
- .long CPU0_DGB_PPU_IRQHandler /* 18: CPU0 Debug PPU Interrupt */
- .long CPU1_DGB_PPU_IRQHandler /* 19: CPU1 Debug PPU Interrupt */
- .long CRYPTOCELL_PPU_IRQHandler /* 20: CryptoCell PPU Interrupt */
- .long 0 /* 21: Reserved */
- .long RAM0_PPU_IRQHandler /* 22: RAM 0 PPU Interrupt */
- .long RAM1_PPU_IRQHandler /* 23: RAM 1 PPU Interrupt */
- .long RAM2_PPU_IRQHandler /* 24: RAM 2 PPU Interrupt */
- .long RAM3_PPU_IRQHandler /* 25: RAM 3 PPU Interrupt */
- .long DEBUG_PPU_IRQHandler /* 26: Debug PPU Interrupt */
- .long 0 /* 27: Reserved */
- .long CPU0_CTI_IRQHandler /* 28: CPU0 CTI Interrupt */
- .long CPU1_CTI_IRQHandler /* 29: CPU1 CTI Interrupt */
- .long 0 /* 30: Reserved */
- .long 0 /* 31: Reserved */
-
- /* External interrupts */
- .long 0 /* 32: Reserved */
- .long GpTimer_IRQHandler /* 33: General Purpose Timer */
- .long I2C0_IRQHandler /* 34: I2C0 */
- .long I2C1_IRQHandler /* 35: I2C1 */
- .long I2S_IRQHandler /* 36: I2S */
- .long SPI_IRQHandler /* 37: SPI */
- .long QSPI_IRQHandler /* 38: QSPI */
- .long UARTRX0_Handler /* 39: UART0 receive FIFO interrupt */
- .long UARTTX0_Handler /* 40: UART0 transmit FIFO interrupt */
- .long UART0_RxTimeout_IRQHandler /* 41: UART0 receive timeout interrupt */
- .long UART0_ModemStatus_IRQHandler /* 42: UART0 modem status interrupt */
- .long UART0_Error_IRQHandler /* 43: UART0 error interrupt */
- .long UART0_IRQHandler /* 44: UART0 interrupt */
- .long UARTRX1_Handler /* 45: UART0 receive FIFO interrupt */
- .long UARTTX1_Handler /* 46: UART0 transmit FIFO interrupt */
- .long UART1_RxTimeout_IRQHandler /* 47: UART0 receive timeout interrupt */
- .long UART1_ModemStatus_IRQHandler /* 48: UART0 modem status interrupt */
- .long UART1_Error_IRQHandler /* 49: UART0 error interrupt */
- .long UART1_IRQHandler /* 50: UART0 interrupt */
- .long GPIO_0_IRQHandler /* 51: GPIO 0 interrupt */
- .long GPIO_1_IRQHandler /* 52: GPIO 1 interrupt */
- .long GPIO_2_IRQHandler /* 53: GPIO 2 interrupt */
- .long GPIO_3_IRQHandler /* 54: GPIO 3 interrupt */
- .long GPIO_4_IRQHandler /* 55: GPIO 4 interrupt */
- .long GPIO_5_IRQHandler /* 56: GPIO 5 interrupt */
- .long GPIO_6_IRQHandler /* 57: GPIO 6 interrupt */
- .long GPIO_7_IRQHandler /* 58: GPIO 7 interrupt */
- .long GPIO_8_IRQHandler /* 59: GPIO 8 interrupt */
- .long GPIO_9_IRQHandler /* 60: GPIO 9 interrupt */
- .long GPIO_10_IRQHandler /* 61: GPIO 10 interrupt */
- .long GPIO_11_IRQHandler /* 62: GPIO 11 interrupt */
- .long GPIO_12_IRQHandler /* 63: GPIO 12 interrupt */
- .long GPIO_13_IRQHandler /* 64: GPIO 13 interrupt */
- .long GPIO_14_IRQHandler /* 65: GPIO 14 interrupt */
- .long GPIO_15_IRQHandler /* 66: GPIO 15 interrupt */
- .long Combined_IRQHandler /* 67: Combined interrupt */
- .long PVT_IRQHandler /* 68: PVT sensor interrupt */
- .long 0 /* 69: Reserved */
- .long PWM_0_IRQHandler /* 70: PWM0 interrupt */
- .long RTC_IRQHandler /* 71: RTC interrupt */
- .long GpTimer0_IRQHandler /* 72: General Purpose Timer0 */
- .long GpTimer1_IRQHandler /* 73: General Purpose Timer1 */
- .long PWM_1_IRQHandler /* 74: PWM1 interrupt */
- .long PWM_2_IRQHandler /* 75: PWM2 interrupt */
- .long IOMUX_IRQHandler /* 76: IOMUX interrupt */
-
- .size __Vectors, . - __Vectors
-
- .text
- .thumb
- .thumb_func
- .align 2
- .globl Reset_Handler
- .type Reset_Handler, %function
-Reset_Handler:
-/* Firstly it copies data from read only memory to RAM. There are two schemes
- * to copy. One can copy more than one sections. Another can only copy
- * one section. The former scheme needs more instructions and read-only
- * data to implement than the latter.
- * Macro __STARTUP_COPY_MULTIPLE is used to choose between two schemes. */
-
-#ifdef __STARTUP_COPY_MULTIPLE
-/* Multiple sections scheme.
- *
- * Between symbol address __copy_table_start__ and __copy_table_end__,
- * there are array of triplets, each of which specify:
- * offset 0: LMA of start of a section to copy from
- * offset 4: VMA of start of a section to copy to
- * offset 8: size of the section to copy. Must be multiply of 4
- *
- * All addresses must be aligned to 4 bytes boundary.
- */
- ldr r4, =__copy_table_start__
- ldr r5, =__copy_table_end__
-
-.L_loop0:
- cmp r4, r5
- bge .L_loop0_done
- ldr r1, [r4]
- ldr r2, [r4, #4]
- ldr r3, [r4, #8]
-
-.L_loop0_0:
- subs r3, #4
- ittt ge
- ldrge r0, [r1, r3]
- strge r0, [r2, r3]
- bge .L_loop0_0
-
- adds r4, #12
- b .L_loop0
-
-.L_loop0_done:
-#else
-/* Single section scheme.
- *
- * The ranges of copy from/to are specified by following symbols
- * __etext: LMA of start of the section to copy from. Usually end of text
- * __data_start__: VMA of start of the section to copy to
- * __data_end__: VMA of end of the section to copy to
- *
- * All addresses must be aligned to 4 bytes boundary.
- */
- ldr r1, =__etext
- ldr r2, =__data_start__
- ldr r3, =__data_end__
-
-.L_loop1:
- cmp r2, r3
- ittt lt
- ldrlt r0, [r1], #4
- strlt r0, [r2], #4
- blt .L_loop1
-#endif /*__STARTUP_COPY_MULTIPLE */
-
-/* This part of work usually is done in C library startup code. Otherwise,
- * define this macro to enable it in this startup.
- *
- * There are two schemes too. One can clear multiple BSS sections. Another
- * can only clear one section. The former is more size expensive than the
- * latter.
- *
- * Define macro __STARTUP_CLEAR_BSS_MULTIPLE to choose the former.
- * Otherwise efine macro __STARTUP_CLEAR_BSS to choose the later.
- */
-#ifdef __STARTUP_CLEAR_BSS_MULTIPLE
-/* Multiple sections scheme.
- *
- * Between symbol address __copy_table_start__ and __copy_table_end__,
- * there are array of tuples specifying:
- * offset 0: Start of a BSS section
- * offset 4: Size of this BSS section. Must be multiply of 4
- */
- ldr r3, =__zero_table_start__
- ldr r4, =__zero_table_end__
-
-.L_loop2:
- cmp r3, r4
- bge .L_loop2_done
- ldr r1, [r3]
- ldr r2, [r3, #4]
- movs r0, 0
-
-.L_loop2_0:
- subs r2, #4
- itt ge
- strge r0, [r1, r2]
- bge .L_loop2_0
-
- adds r3, #8
- b .L_loop2
-.L_loop2_done:
-#elif defined (__STARTUP_CLEAR_BSS)
-/* Single BSS section scheme.
- *
- * The BSS section is specified by following symbols
- * __bss_start__: start of the BSS section.
- * __bss_end__: end of the BSS section.
- *
- * Both addresses must be aligned to 4 bytes boundary.
- */
- ldr r1, =__bss_start__
- ldr r2, =__bss_end__
-
- movs r0, 0
-.L_loop3:
- cmp r1, r2
- itt lt
- strlt r0, [r1], #4
- blt .L_loop3
-#endif /* __STARTUP_CLEAR_BSS_MULTIPLE || __STARTUP_CLEAR_BSS */
-
- mrs r0, control /* Get control value */
- orr r0, r0, #2 /* Select switch to PSP */
- msr control, r0
- ldr r0, =Image$$ARM_LIB_STACK$$ZI$$Limit
- msr psp, r0
-
-#ifndef __START
-#define __START _start
-#endif
- bl __START
-
- .pool
- .size Reset_Handler, . - Reset_Handler
-
-
-/* Macro to define default handlers. */
- .macro def_irq_handler handler_name
- .align 1
- .thumb_func
- .weak \handler_name
- \handler_name:
- b \handler_name
- .endm
-
- def_irq_handler NMI_Handler
- def_irq_handler HardFault_Handler
- def_irq_handler MemManage_Handler
- def_irq_handler BusFault_Handler
- def_irq_handler UsageFault_Handler
- def_irq_handler SVC_Handler
- def_irq_handler DebugMon_Handler
- def_irq_handler PendSV_Handler
- def_irq_handler SysTick_Handler
-
- /* Core interrupts */
- def_irq_handler NS_WATCHDOG_RESET_IRQHandler /* 0: Non-Secure Watchdog Reset Request Interrupt */
- def_irq_handler NS_WATCHDOG_IRQHandler /* 1: Non-Secure Watchdog Interrupt */
- def_irq_handler S32K_TIMER_IRQHandler /* 2: S32K Timer Interrupt */
- def_irq_handler TIMER0_IRQHandler /* 3: CMSDK Timer 0 Interrupt */
- def_irq_handler TIMER1_Handler /* 4: CMSDK Timer 1 Interrupt */
- def_irq_handler DUALTIMER_IRQHandler /* 5: CMSDK Dual Timer Interrupt */
- def_irq_handler MHU0_IRQHandler /* 6: Message Handling Unit 0 Interrupt */
- def_irq_handler MHU1_IRQHandler /* 7: Message Handling Unit 1 Interrupt */
- def_irq_handler CRYPTOCELL_IRQHandler /* 8: CryptoCell-312 Interrupt */
- def_irq_handler I_CACHE_INV_ERR_IRQHandler /* 13: Intsruction Cache Invalidation Interrupt */
- def_irq_handler SYS_PPU_IRQHandler /* 15: System PPU Interrupt */
- def_irq_handler CPU0_PPU_IRQHandler /* 16: CPU0 PPU Interrupt */
- def_irq_handler CPU1_PPU_IRQHandler /* 17: CPU1 PPU Interrupt */
- def_irq_handler CPU0_DGB_PPU_IRQHandler /* 18: CPU0 Debug PPU Interrupt */
- def_irq_handler CPU1_DGB_PPU_IRQHandler /* 19: CPU1 Debug PPU Interrupt */
- def_irq_handler CRYPTOCELL_PPU_IRQHandler /* 20: CryptoCell PPU Interrupt */
- def_irq_handler RAM0_PPU_IRQHandler /* 22: RAM 0 PPU Interrupt */
- def_irq_handler RAM1_PPU_IRQHandler /* 23: RAM 1 PPU Interrupt */
- def_irq_handler RAM2_PPU_IRQHandler /* 24: RAM 2 PPU Interrupt */
- def_irq_handler RAM3_PPU_IRQHandler /* 25: RAM 3 PPU Interrupt */
- def_irq_handler DEBUG_PPU_IRQHandler /* 26: Debug PPU Interrupt */
- def_irq_handler CPU0_CTI_IRQHandler /* 28: CPU0 CTI Interrupt */
- def_irq_handler CPU1_CTI_IRQHandler /* 29: CPU1 CTI Interrupt */
-
- /* External interrupts */
- def_irq_handler GpTimer_IRQHandler /* 33: General Purpose Timer */
- def_irq_handler I2C0_IRQHandler /* 34: I2C0 */
- def_irq_handler I2C1_IRQHandler /* 35: I2C1 */
- def_irq_handler I2S_IRQHandler /* 36: I2S */
- def_irq_handler SPI_IRQHandler /* 37: SPI */
- def_irq_handler QSPI_IRQHandler /* 38: QSPI */
- def_irq_handler UARTRX0_Handler /* 39: UART0 receive FIFO interrupt */
- def_irq_handler UARTTX0_Handler /* 40: UART0 transmit FIFO interrupt */
- def_irq_handler UART0_RxTimeout_IRQHandler /* 41: UART0 receive timeout interrupt */
- def_irq_handler UART0_ModemStatus_IRQHandler /* 42: UART0 modem status interrupt */
- def_irq_handler UART0_Error_IRQHandler /* 43: UART0 error interrupt */
- def_irq_handler UART0_IRQHandler /* 44: UART0 interrupt */
- def_irq_handler UARTRX1_Handler /* 45: UART0 receive FIFO interrupt */
- def_irq_handler UARTTX1_Handler /* 46: UART0 transmit FIFO interrupt */
- def_irq_handler UART1_RxTimeout_IRQHandler /* 47: UART0 receive timeout interrupt */
- def_irq_handler UART1_ModemStatus_IRQHandler /* 48: UART0 modem status interrupt */
- def_irq_handler UART1_Error_IRQHandler /* 49: UART0 error interrupt */
- def_irq_handler UART1_IRQHandler /* 50: UART0 interrupt */
- def_irq_handler GPIO_0_IRQHandler /* 51: GPIO 0 interrupt */
- def_irq_handler GPIO_1_IRQHandler /* 52: GPIO 1 interrupt */
- def_irq_handler GPIO_2_IRQHandler /* 53: GPIO 2 interrupt */
- def_irq_handler GPIO_3_IRQHandler /* 54: GPIO 3 interrupt */
- def_irq_handler GPIO_4_IRQHandler /* 55: GPIO 4 interrupt */
- def_irq_handler GPIO_5_IRQHandler /* 56: GPIO 5 interrupt */
- def_irq_handler GPIO_6_IRQHandler /* 57: GPIO 6 interrupt */
- def_irq_handler GPIO_7_IRQHandler /* 58: GPIO 7 interrupt */
- def_irq_handler GPIO_8_IRQHandler /* 59: GPIO 8 interrupt */
- def_irq_handler GPIO_9_IRQHandler /* 60: GPIO 9 interrupt */
- def_irq_handler GPIO_10_IRQHandler /* 61: GPIO 10 interrupt */
- def_irq_handler GPIO_11_IRQHandler /* 62: GPIO 11 interrupt */
- def_irq_handler GPIO_12_IRQHandler /* 63: GPIO 12 interrupt */
- def_irq_handler GPIO_13_IRQHandler /* 64: GPIO 13 interrupt */
- def_irq_handler GPIO_14_IRQHandler /* 65: GPIO 14 interrupt */
- def_irq_handler GPIO_15_IRQHandler /* 66: GPIO 15 interrupt */
- def_irq_handler Combined_IRQHandler /* 67: Combined interrupt */
- def_irq_handler PVT_IRQHandler /* 68: PVT sensor interrupt */
- def_irq_handler PWM_0_IRQHandler /* 70: PWM0 interrupt */
- def_irq_handler RTC_IRQHandler /* 71: RTC interrupt */
- def_irq_handler GpTimer0_IRQHandler /* 72: General Purpose Timer0 */
- def_irq_handler GpTimer1_IRQHandler /* 73: General Purpose Timer1 */
- def_irq_handler PWM_1_IRQHandler /* 74: PWM1 interrupt */
- def_irq_handler PWM_2_IRQHandler /* 75: PWM2 interrupt */
- def_irq_handler IOMUX_IRQHandler /* 76: IOMUX interrupt */
-
- .end
diff --git a/platform/ext/target/musca_a/Device/Source/gcc/startup_cmsdk_musca_s.S b/platform/ext/target/musca_a/Device/Source/gcc/startup_cmsdk_musca_s.S
deleted file mode 100644
index 639ce0b..0000000
--- a/platform/ext/target/musca_a/Device/Source/gcc/startup_cmsdk_musca_s.S
+++ /dev/null
@@ -1,365 +0,0 @@
-;/*
-; * Copyright (c) 2009-2020 Arm Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; *
-; *
-; * This file is derivative of CMSIS V5.00 startup_ARMCM33.S
-; */
-
-#include "tfm_plat_config.h"
-
- .syntax unified
- .arch armv8-m.main
-
- .section .vectors
- .align 2
- .globl __Vectors
-__Vectors:
- .long Image$$ARM_LIB_STACK_MSP$$ZI$$Limit /* Top of Stack */
- .long Reset_Handler /* Reset Handler */
- .long NMI_Handler /* NMI Handler */
- .long HardFault_Handler /* Hard Fault Handler */
- .long MemManage_Handler /* MPU Fault Handler */
- .long BusFault_Handler /* Bus Fault Handler */
- .long UsageFault_Handler /* Usage Fault Handler */
- .long SecureFault_Handler /* Secure Fault Handler */
- .long 0 /* Reserved */
- .long 0 /* Reserved */
- .long 0 /* Reserved */
- .long SVC_Handler /* SVCall Handler */
- .long DebugMon_Handler /* Debug Monitor Handler */
- .long 0 /* Reserved */
- .long PendSV_Handler /* PendSV Handler */
- .long SysTick_Handler /* SysTick Handler */
-
- /* Core interrupts */
- .long NS_WATCHDOG_RESET_IRQHandler /* 0: Non-Secure Watchdog Reset Request Interrupt */
- .long NS_WATCHDOG_IRQHandler /* 1: Non-Secure Watchdog Interrupt */
- .long S32K_TIMER_IRQHandler /* 2: S32K Timer Interrupt */
- .long TFM_TIMER0_IRQ_Handler /* 3: CMSDK Timer 0 Interrupt */
- .long TIMER1_IRQHandler /* 4: CMSDK Timer 1 Interrupt */
- .long DUALTIMER_IRQHandler /* 5: CMSDK Dual Timer Interrupt */
- .long MHU0_IRQHandler /* 6: Message Handling Unit 0 Interrupt */
- .long MHU1_IRQHandler /* 7: Message Handling Unit 1 Interrupt */
- .long CRYPTOCELL_IRQHandler /* 8: CryptoCell-312 Interrupt */
- .long MPC_Handler /* 9: Secure Combined MPC Interrupt */
- .long PPC_Handler /* 10: Secure Combined PPC Interrupt */
- .long S_MSC_COMBINED_IRQHandler /* 11: Secure Combined MSC Interrupt */
- .long S_BRIDGE_ERR_IRQHandler /* 12: Secure Bridge Error Combined Interrupt */
- .long I_CACHE_INV_ERR_IRQHandler /* 13: Intsruction Cache Invalidation Interrupt */
- .long 0 /* 14: Reserved */
- .long SYS_PPU_IRQHandler /* 15: System PPU Interrupt */
- .long CPU0_PPU_IRQHandler /* 16: CPU0 PPU Interrupt */
- .long CPU1_PPU_IRQHandler /* 17: CPU1 PPU Interrupt */
- .long CPU0_DGB_PPU_IRQHandler /* 18: CPU0 Debug PPU Interrupt */
- .long CPU1_DGB_PPU_IRQHandler /* 19: CPU1 Debug PPU Interrupt */
- .long CRYPTOCELL_PPU_IRQHandler /* 20: CryptoCell PPU Interrupt */
- .long 0 /* 21: Reserved */
- .long RAM0_PPU_IRQHandler /* 22: RAM 0 PPU Interrupt */
- .long RAM1_PPU_IRQHandler /* 23: RAM 1 PPU Interrupt */
- .long RAM2_PPU_IRQHandler /* 24: RAM 2 PPU Interrupt */
- .long RAM3_PPU_IRQHandler /* 25: RAM 3 PPU Interrupt */
- .long DEBUG_PPU_IRQHandler /* 26: Debug PPU Interrupt */
- .long 0 /* 27: Reserved */
- .long CPU0_CTI_IRQHandler /* 28: CPU0 CTI Interrupt */
- .long CPU1_CTI_IRQHandler /* 29: CPU1 CTI Interrupt */
- .long 0 /* 30: Reserved */
- .long 0 /* 31: Reserved */
-
- /* External interrupts */
- .long 0 /* 32: Reserved */
- .long GpTimer_IRQHandler /* 33: General Purpose Timer */
- .long I2C0_IRQHandler /* 34: I2C0 */
- .long I2C1_IRQHandler /* 35: I2C1 */
- .long I2S_IRQHandler /* 36: I2S */
- .long SPI_IRQHandler /* 37: SPI */
- .long QSPI_IRQHandler /* 38: QSPI */
- .long UARTRX0_Handler /* 39: UART0 receive FIFO interrupt */
- .long UARTTX0_Handler /* 40: UART0 transmit FIFO interrupt */
- .long UART0_RxTimeout_IRQHandler /* 41: UART0 receive timeout interrupt */
- .long UART0_ModemStatus_IRQHandler /* 42: UART0 modem status interrupt */
- .long UART0_Error_IRQHandler /* 43: UART0 error interrupt */
- .long UART0_IRQHandler /* 44: UART0 interrupt */
- .long UARTRX1_Handler /* 45: UART0 receive FIFO interrupt */
- .long UARTTX1_Handler /* 46: UART0 transmit FIFO interrupt */
- .long UART1_RxTimeout_IRQHandler /* 47: UART0 receive timeout interrupt */
- .long UART1_ModemStatus_IRQHandler /* 48: UART0 modem status interrupt */
- .long UART1_Error_IRQHandler /* 49: UART0 error interrupt */
- .long UART1_IRQHandler /* 50: UART0 interrupt */
- .long GPIO_0_IRQHandler /* 51: GPIO 0 interrupt */
- .long GPIO_1_IRQHandler /* 52: GPIO 1 interrupt */
- .long GPIO_2_IRQHandler /* 53: GPIO 2 interrupt */
- .long GPIO_3_IRQHandler /* 54: GPIO 3 interrupt */
- .long GPIO_4_IRQHandler /* 55: GPIO 4 interrupt */
- .long GPIO_5_IRQHandler /* 56: GPIO 5 interrupt */
- .long GPIO_6_IRQHandler /* 57: GPIO 6 interrupt */
- .long GPIO_7_IRQHandler /* 58: GPIO 7 interrupt */
- .long GPIO_8_IRQHandler /* 59: GPIO 8 interrupt */
- .long GPIO_9_IRQHandler /* 60: GPIO 9 interrupt */
- .long GPIO_10_IRQHandler /* 61: GPIO 10 interrupt */
- .long GPIO_11_IRQHandler /* 62: GPIO 11 interrupt */
- .long GPIO_12_IRQHandler /* 63: GPIO 12 interrupt */
- .long GPIO_13_IRQHandler /* 64: GPIO 13 interrupt */
- .long GPIO_14_IRQHandler /* 65: GPIO 14 interrupt */
- .long GPIO_15_IRQHandler /* 66: GPIO 15 interrupt */
- .long Combined_IRQHandler /* 67: Combined interrupt */
- .long PVT_IRQHandler /* 68: PVT sensor interrupt */
- .long 0 /* 69: Reserved */
- .long PWM_0_IRQHandler /* 70: PWM0 interrupt */
- .long RTC_IRQHandler /* 71: RTC interrupt */
- .long GpTimer0_IRQHandler /* 72: General Purpose Timer0 */
- .long GpTimer1_IRQHandler /* 73: General Purpose Timer1 */
- .long PWM_1_IRQHandler /* 74: PWM1 interrupt */
- .long PWM_2_IRQHandler /* 75: PWM2 interrupt */
- .long IOMUX_IRQHandler /* 76: IOMUX interrupt */
-
- .size __Vectors, . - __Vectors
-
- .text
- .thumb
- .thumb_func
- .align 2
- .globl Reset_Handler
- .type Reset_Handler, %function
-Reset_Handler:
-/* Firstly it copies data from read only memory to RAM. There are two schemes
- * to copy. One can copy more than one sections. Another can only copy
- * one section. The former scheme needs more instructions and read-only
- * data to implement than the latter.
- * Macro __STARTUP_COPY_MULTIPLE is used to choose between two schemes. */
-
-#ifdef __STARTUP_COPY_MULTIPLE
-/* Multiple sections scheme.
- *
- * Between symbol address __copy_table_start__ and __copy_table_end__,
- * there are array of triplets, each of which specify:
- * offset 0: LMA of start of a section to copy from
- * offset 4: VMA of start of a section to copy to
- * offset 8: size of the section to copy. Must be multiply of 4
- *
- * All addresses must be aligned to 4 bytes boundary.
- */
- ldr r4, =__copy_table_start__
- ldr r5, =__copy_table_end__
-
-.L_loop0:
- cmp r4, r5
- bge .L_loop0_done
- ldr r1, [r4]
- ldr r2, [r4, #4]
- ldr r3, [r4, #8]
-
-.L_loop0_0:
- subs r3, #4
- ittt ge
- ldrge r0, [r1, r3]
- strge r0, [r2, r3]
- bge .L_loop0_0
-
- adds r4, #12
- b .L_loop0
-
-.L_loop0_done:
-#else
-/* Single section scheme.
- *
- * The ranges of copy from/to are specified by following symbols
- * __etext: LMA of start of the section to copy from. Usually end of text
- * __data_start__: VMA of start of the section to copy to
- * __data_end__: VMA of end of the section to copy to
- *
- * All addresses must be aligned to 4 bytes boundary.
- */
- ldr r1, =__etext
- ldr r2, =__data_start__
- ldr r3, =__data_end__
-
-.L_loop1:
- cmp r2, r3
- ittt lt
- ldrlt r0, [r1], #4
- strlt r0, [r2], #4
- blt .L_loop1
-#endif /*__STARTUP_COPY_MULTIPLE */
-
-/* This part of work usually is done in C library startup code. Otherwise,
- * define this macro to enable it in this startup.
- *
- * There are two schemes too. One can clear multiple BSS sections. Another
- * can only clear one section. The former is more size expensive than the
- * latter.
- *
- * Define macro __STARTUP_CLEAR_BSS_MULTIPLE to choose the former.
- * Otherwise efine macro __STARTUP_CLEAR_BSS to choose the later.
- */
-#ifdef __STARTUP_CLEAR_BSS_MULTIPLE
-/* Multiple sections scheme.
- *
- * Between symbol address __copy_table_start__ and __copy_table_end__,
- * there are array of tuples specifying:
- * offset 0: Start of a BSS section
- * offset 4: Size of this BSS section. Must be multiply of 4
- */
- ldr r3, =__zero_table_start__
- ldr r4, =__zero_table_end__
-
-.L_loop2:
- cmp r3, r4
- bge .L_loop2_done
- ldr r1, [r3]
- ldr r2, [r3, #4]
- movs r0, 0
-
-.L_loop2_0:
- subs r2, #4
- itt ge
- strge r0, [r1, r2]
- bge .L_loop2_0
-
- adds r3, #8
- b .L_loop2
-.L_loop2_done:
-#elif defined (__STARTUP_CLEAR_BSS)
-/* Single BSS section scheme.
- *
- * The BSS section is specified by following symbols
- * __bss_start__: start of the BSS section.
- * __bss_end__: end of the BSS section.
- *
- * Both addresses must be aligned to 4 bytes boundary.
- */
- ldr r1, =__bss_start__
- ldr r2, =__bss_end__
-
- movs r0, 0
-.L_loop3:
- cmp r1, r2
- itt lt
- strlt r0, [r1], #4
- blt .L_loop3
-#endif /* __STARTUP_CLEAR_BSS_MULTIPLE || __STARTUP_CLEAR_BSS */
-
- cpsid i /* Disable IRQs */
- bl SystemInit
-
- mrs r0, control /* Get control value */
- orr r0, r0, #2 /* Select switch to PSP */
- msr control, r0
- ldr r0, =Image$$ARM_LIB_STACK$$ZI$$Limit
- msr psp, r0
-
-#ifndef __START
-#define __START _start
-#endif
- bl __START
-
- .pool
- .size Reset_Handler, . - Reset_Handler
-
-
-/* Macro to define default handlers. */
- .macro def_irq_handler handler_name
- .align 1
- .thumb_func
- .weak \handler_name
- \handler_name:
- b \handler_name
- .endm
-
- def_irq_handler NMI_Handler
- def_irq_handler HardFault_Handler
- def_irq_handler MemManage_Handler
- def_irq_handler BusFault_Handler
- def_irq_handler UsageFault_Handler
- def_irq_handler SecureFault_Handler
- def_irq_handler SVC_Handler
- def_irq_handler DebugMon_Handler
- def_irq_handler PendSV_Handler
- def_irq_handler SysTick_Handler
-
- /* Core interrupts */
- def_irq_handler NS_WATCHDOG_RESET_IRQHandler /* 0: Non-Secure Watchdog Reset Request Interrupt */
- def_irq_handler NS_WATCHDOG_IRQHandler /* 1: Non-Secure Watchdog Interrupt */
- def_irq_handler S32K_TIMER_IRQHandler /* 2: S32K Timer Interrupt */
- def_irq_handler TFM_TIMER0_IRQ_Handler /* 3: CMSDK Timer 0 Interrupt */
- def_irq_handler TIMER1_IRQHandler /* 4: CMSDK Timer 1 Interrupt */
- def_irq_handler DUALTIMER_IRQHandler /* 5: CMSDK Dual Timer Interrupt */
- def_irq_handler MHU0_IRQHandler /* 6: Message Handling Unit 0 Interrupt */
- def_irq_handler MHU1_IRQHandler /* 7: Message Handling Unit 1 Interrupt */
- def_irq_handler CRYPTOCELL_IRQHandler /* 8: CryptoCell-312 Interrupt */
- def_irq_handler MPC_Handler /* 9: Secure Combined MPC Interrupt */
- def_irq_handler PPC_Handler /* 10: Secure Combined PPC Interrupt */
- def_irq_handler S_MSC_COMBINED_IRQHandler /* 11: Secure Combined MSC Interrupt */
- def_irq_handler S_BRIDGE_ERR_IRQHandler /* 12: Secure Bridge Error Combined Interrupt */
- def_irq_handler I_CACHE_INV_ERR_IRQHandler /* 13: Intsruction Cache Invalidation Interrupt */
- def_irq_handler SYS_PPU_IRQHandler /* 15: System PPU Interrupt */
- def_irq_handler CPU0_PPU_IRQHandler /* 16: CPU0 PPU Interrupt */
- def_irq_handler CPU1_PPU_IRQHandler /* 17: CPU1 PPU Interrupt */
- def_irq_handler CPU0_DGB_PPU_IRQHandler /* 18: CPU0 Debug PPU Interrupt */
- def_irq_handler CPU1_DGB_PPU_IRQHandler /* 19: CPU1 Debug PPU Interrupt */
- def_irq_handler CRYPTOCELL_PPU_IRQHandler /* 20: CryptoCell PPU Interrupt */
- def_irq_handler RAM0_PPU_IRQHandler /* 22: RAM 0 PPU Interrupt */
- def_irq_handler RAM1_PPU_IRQHandler /* 23: RAM 1 PPU Interrupt */
- def_irq_handler RAM2_PPU_IRQHandler /* 24: RAM 2 PPU Interrupt */
- def_irq_handler RAM3_PPU_IRQHandler /* 25: RAM 3 PPU Interrupt */
- def_irq_handler DEBUG_PPU_IRQHandler /* 26: Debug PPU Interrupt */
- def_irq_handler CPU0_CTI_IRQHandler /* 28: CPU0 CTI Interrupt */
- def_irq_handler CPU1_CTI_IRQHandler /* 29: CPU1 CTI Interrupt */
-
- /* External interrupts */
- def_irq_handler GpTimer_IRQHandler /* 33: General Purpose Timer */
- def_irq_handler I2C0_IRQHandler /* 34: I2C0 */
- def_irq_handler I2C1_IRQHandler /* 35: I2C1 */
- def_irq_handler I2S_IRQHandler /* 36: I2S */
- def_irq_handler SPI_IRQHandler /* 37: SPI */
- def_irq_handler QSPI_IRQHandler /* 38: QSPI */
- def_irq_handler UARTRX0_Handler /* 39: UART0 receive FIFO interrupt */
- def_irq_handler UARTTX0_Handler /* 40: UART0 transmit FIFO interrupt */
- def_irq_handler UART0_RxTimeout_IRQHandler /* 41: UART0 receive timeout interrupt */
- def_irq_handler UART0_ModemStatus_IRQHandler /* 42: UART0 modem status interrupt */
- def_irq_handler UART0_Error_IRQHandler /* 43: UART0 error interrupt */
- def_irq_handler UART0_IRQHandler /* 44: UART0 interrupt */
- def_irq_handler UARTRX1_Handler /* 45: UART0 receive FIFO interrupt */
- def_irq_handler UARTTX1_Handler /* 46: UART0 transmit FIFO interrupt */
- def_irq_handler UART1_RxTimeout_IRQHandler /* 47: UART0 receive timeout interrupt */
- def_irq_handler UART1_ModemStatus_IRQHandler /* 48: UART0 modem status interrupt */
- def_irq_handler UART1_Error_IRQHandler /* 49: UART0 error interrupt */
- def_irq_handler UART1_IRQHandler /* 50: UART0 interrupt */
- def_irq_handler GPIO_0_IRQHandler /* 51: GPIO 0 interrupt */
- def_irq_handler GPIO_1_IRQHandler /* 52: GPIO 1 interrupt */
- def_irq_handler GPIO_2_IRQHandler /* 53: GPIO 2 interrupt */
- def_irq_handler GPIO_3_IRQHandler /* 54: GPIO 3 interrupt */
- def_irq_handler GPIO_4_IRQHandler /* 55: GPIO 4 interrupt */
- def_irq_handler GPIO_5_IRQHandler /* 56: GPIO 5 interrupt */
- def_irq_handler GPIO_6_IRQHandler /* 57: GPIO 6 interrupt */
- def_irq_handler GPIO_7_IRQHandler /* 58: GPIO 7 interrupt */
- def_irq_handler GPIO_8_IRQHandler /* 59: GPIO 8 interrupt */
- def_irq_handler GPIO_9_IRQHandler /* 60: GPIO 9 interrupt */
- def_irq_handler GPIO_10_IRQHandler /* 61: GPIO 10 interrupt */
- def_irq_handler GPIO_11_IRQHandler /* 62: GPIO 11 interrupt */
- def_irq_handler GPIO_12_IRQHandler /* 63: GPIO 12 interrupt */
- def_irq_handler GPIO_13_IRQHandler /* 64: GPIO 13 interrupt */
- def_irq_handler GPIO_14_IRQHandler /* 65: GPIO 14 interrupt */
- def_irq_handler GPIO_15_IRQHandler /* 66: GPIO 15 interrupt */
- def_irq_handler Combined_IRQHandler /* 67: Combined interrupt */
- def_irq_handler PVT_IRQHandler /* 68: PVT sensor interrupt */
- def_irq_handler PWM_0_IRQHandler /* 70: PWM0 interrupt */
- def_irq_handler RTC_IRQHandler /* 71: RTC interrupt */
- def_irq_handler GpTimer0_IRQHandler /* 72: General Purpose Timer0 */
- def_irq_handler GpTimer1_IRQHandler /* 73: General Purpose Timer1 */
- def_irq_handler PWM_1_IRQHandler /* 74: PWM1 interrupt */
- def_irq_handler PWM_2_IRQHandler /* 75: PWM2 interrupt */
- def_irq_handler IOMUX_IRQHandler /* 76: IOMUX interrupt */
-
- .end
diff --git a/platform/ext/target/musca_a/Device/Source/iar/musca_bl2.icf b/platform/ext/target/musca_a/Device/Source/iar/musca_bl2.icf
deleted file mode 100644
index 80b950f..0000000
--- a/platform/ext/target/musca_a/Device/Source/iar/musca_bl2.icf
+++ /dev/null
@@ -1,72 +0,0 @@
-/*
- * Copyright (c) 2020 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- *
- *
- * This file is derivative of ../armclang/musca_bl2.sct
- */
-
-/* Linker script to configure memory regions. */
-/* This file will be run trough the pre-processor. */
-
-#include "region_defs.h"
-
-initialize by copy with packing = none { readonly, readwrite }
- except{ section .rst_handler,
- section .intvec,
- ro object startup_cmsdk_musca_bl2.o*,
- ro object system_core_init.o,
- ro object cstartup_M.o,
- ro object low_level_init.o,
- ro object data_init.o,
- ro object zero_init3.o,
- ro object copy_init3.o,
- ro object cmain.o};
-
-define block ER_CODE with fixed order, alignment = 8 {
- section .intvec,
- readonly
- };
-define block LR_CODE with fixed order, maximum size = BL2_CODE_SIZE {block ER_CODE};
-place at address BL2_CODE_START {block LR_CODE};
-
-define block ER_CODE_SRAM with fixed order, alignment = 8 {
- rw section .text,
- rw section .rodata
- };
-place at address BL2_CODE_SRAM_BASE {block ER_CODE_SRAM};
-
-define block TFM_SHARED_DATA with alignment = 32, size = BOOT_TFM_SHARED_DATA_SIZE { };
-define block ER_DATA with alignment = 32 {readwrite};
-define block ARM_LIB_STACK with alignment = 32, size = BL2_MSP_STACK_SIZE { };
-define block HEAP with alignment = 8, size = BL2_HEAP_SIZE { };
-define block ARM_LIB_HEAP with alignment = 8, size = BL2_HEAP_SIZE { };
-define overlay HEAP_OVL {block HEAP};
-define overlay HEAP_OVL {block ARM_LIB_HEAP};
-keep {block TFM_SHARED_DATA, block ER_DATA, block ARM_LIB_STACK,
- block HEAP, block ARM_LIB_HEAP};
-
-if (isdefinedsymbol(__USE_DLIB_PERTHREAD))
-{
- // Required in a multi-threaded application
- initialize by copy with packing = none { section __DLIB_PERTHREAD };
-}
-
-define block DATA with fixed order, maximum size = BL2_DATA_SIZE {
- block TFM_SHARED_DATA,
- block ER_DATA,
- block ARM_LIB_STACK,
- overlay HEAP_OVL
-};
-place at address BL2_DATA_START {block DATA};
diff --git a/platform/ext/target/musca_a/Device/Source/iar/musca_ns.icf b/platform/ext/target/musca_a/Device/Source/iar/musca_ns.icf
deleted file mode 100644
index 72c3d88..0000000
--- a/platform/ext/target/musca_a/Device/Source/iar/musca_ns.icf
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * Copyright (c) 2020 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- *
- *
- * This file is derivative of ../armclang/musca_ns.sct
- */
-
-/* Linker script to configure memory regions. */
-/* This file will be run trough the pre-processor. */
-
-#include "region_defs.h"
-
-define block ER_CODE with fixed order, alignment = 8 {
- section .intvec,
- readonly};
-define block LR_CODE with fixed order, maximum size = NS_CODE_SIZE {block ER_CODE};
-place at address NS_CODE_START {block LR_CODE};
-
-define block ER_DATA with alignment = 8 {readwrite};
-define block ARM_LIB_STACK_MSP with alignment = 32, size = NS_MSP_STACK_SIZE { };
-define block ARM_LIB_STACK with alignment = 32, size = NS_PSP_STACK_SIZE { };
-define block HEAP with alignment = 8, size = NS_HEAP_SIZE { };
-define block ARM_LIB_HEAP with alignment = 8, size = NS_HEAP_SIZE { };
-define overlay HEAP_OVL {block HEAP};
-define overlay HEAP_OVL {block ARM_LIB_HEAP};
-keep {block ARM_LIB_STACK_MSP, block ARM_LIB_STACK,
- block HEAP, block ARM_LIB_HEAP};
-
-do not initialize { section .noinit };
-initialize by copy { readwrite };
-if (isdefinedsymbol(__USE_DLIB_PERTHREAD))
-{
- // Required in a multi-threaded application
- initialize by copy with packing = none { section __DLIB_PERTHREAD };
-}
-
-define block DATA with fixed order, maximum size = NS_DATA_SIZE {
- block ER_DATA,
- block ARM_LIB_STACK_MSP,
- block ARM_LIB_STACK,
- overlay HEAP_OVL
-};
-place at address NS_DATA_START {block DATA};
diff --git a/platform/ext/target/musca_a/Device/Source/iar/startup_cmsdk_musca_bl2.s b/platform/ext/target/musca_a/Device/Source/iar/startup_cmsdk_musca_bl2.s
deleted file mode 100644
index 47f4768..0000000
--- a/platform/ext/target/musca_a/Device/Source/iar/startup_cmsdk_musca_bl2.s
+++ /dev/null
@@ -1,250 +0,0 @@
-;/*
-; * Copyright (c) 2017-2020 ARM Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; */
-;
-; This file is derivative of CMSIS V5.01 startup_ARMv8MML.s
-; Git SHA: 8a1d9d6ee18b143ae5befefa14d89fb5b3f99c75
-
-;/*
-;//-------- <<< Use Configuration Wizard in Context Menu >>> ------------------
-;*/
-
-
-; <h> Stack Configuration
-; <o> Stack Size (in Bytes) <0x0-0xFFFFFFFF:8>
-; </h>
-
- MODULE ?cstartup
-
- ;; Forward declaration of sections.
- SECTION ARM_LIB_STACK:DATA:NOROOT(3)
-
- SECTION .intvec:CODE:NOROOT(2)
-
- EXTERN __iar_program_start
- EXTERN SystemInit
- PUBLIC __vector_table
- PUBLIC __Vectors
- PUBLIC __Vectors_End
- PUBLIC __Vectors_Size
- DATA
-
-
-__vector_table ;Core Interrupts
- DCD sfe(ARM_LIB_STACK) ; Top of Stack
- DCD Reset_Handler ; Reset Handler
- DCD NMI_Handler ; NMI Handler
- DCD HardFault_Handler ; Hard Fault Handler
- DCD MemManage_Handler ; MPU Fault Handler
- DCD BusFault_Handler ; Bus Fault Handler
- DCD UsageFault_Handler ; Usage Fault Handler
- DCD SecureFault_Handler ; Secure Fault Handler
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD SVC_Handler ; SVCall Handler
- DCD DebugMon_Handler ; Debug Monitor Handler
- DCD 0 ; Reserved
- DCD PendSV_Handler ; PendSV Handler
- DCD SysTick_Handler ; SysTick Handler
- ;SSE-200 Interrupts
- DCD NS_WATCHDOG_RESET_IRQHandler ; 0: Non-Secure Watchdog Reset Request Interrupt
- DCD NS_WATCHDOG_IRQHandler ; 1: Non-Secure Watchdog Interrupt
- DCD S32K_TIMER_IRQHandler ; 2: S32K Timer Interrupt
- DCD TIMER0_IRQHandler ; 3: CMSDK Timer 0 Interrupt
- DCD TIMER1_IRQHandler ; 4: CMSDK Timer 1 Interrupt
- DCD DUALTIMER_IRQHandler ; 5: CMSDK Dual Timer Interrupt
- DCD MHU0_IRQHandler ; 6: Message Handling Unit 0 Interrupt
- DCD MHU1_IRQHandler ; 7: Message Handling Unit 1 Interrupt
- DCD CRYPTOCELL_IRQHandler ; 8: CryptoCell-312 Interrupt
- DCD MPC_Handler ; 9: Secure Combined MPC Interrupt
- DCD PPC_Handler ; 10: Secure Combined PPC Interrupt
- DCD S_MSC_COMBINED_IRQHandler ; 11: Secure Combined MSC Interrupt
- DCD S_BRIDGE_ERR_IRQHandler ; 12: Secure Bridge Error Combined Interrupt
- DCD I_CACHE_INV_ERR_IRQHandler ; 13: Intsruction Cache Invalidation Interrupt
- DCD 0 ; 14: Reserved
- DCD SYS_PPU_IRQHandler ; 15: System PPU Interrupt
- DCD CPU0_PPU_IRQHandler ; 16: CPU0 PPU Interrupt
- DCD CPU1_PPU_IRQHandler ; 17: CPU1 PPU Interrupt
- DCD CPU0_DGB_PPU_IRQHandler ; 18: CPU0 Debug PPU Interrupt
- DCD CPU1_DGB_PPU_IRQHandler ; 19: CPU1 Debug PPU Interrupt
- DCD CRYPTOCELL_PPU_IRQHandler ; 20: CryptoCell PPU Interrupt
- DCD 0 ; 21: Reserved
- DCD RAM0_PPU_IRQHandler ; 22: RAM 0 PPU Interrupt
- DCD RAM1_PPU_IRQHandler ; 23: RAM 1 PPU Interrupt
- DCD RAM2_PPU_IRQHandler ; 24: RAM 2 PPU Interrupt
- DCD RAM3_PPU_IRQHandler ; 25: RAM 3 PPU Interrupt
- DCD DEBUG_PPU_IRQHandler ; 26: Debug PPU Interrupt
- DCD 0 ; 27: Reserved
- DCD CPU0_CTI_IRQHandler ; 28: CPU0 CTI Interrupt
- DCD CPU1_CTI_IRQHandler ; 29: CPU1 CTI Interrupt
- DCD 0 ; 30: Reserved
- DCD 0 ; 31: Reserved
- ;Expansion Interrupts
- DCD 0 ; 32: Reserved
- DCD GpTimer_IRQHandler ; 33: General Purpose Timer
- DCD I2C0_IRQHandler ; 34: I2C0
- DCD I2C1_IRQHandler ; 35: I2C1
- DCD I2S_IRQHandler ; 36: I2S
- DCD SPI_IRQHandler ; 37: SPI
- DCD QSPI_IRQHandler ; 38: QSPI
- DCD UARTRX0_Handler ; 39: UART0 receive FIFO interrupt
- DCD UARTTX0_Handler ; 40: UART0 transmit FIFO interrupt
- DCD UART0_RxTimeout_IRQHandler ; 41: UART0 receive timeout interrupt
- DCD UART0_ModemStatus_IRQHandler ; 42: UART0 modem status interrupt
- DCD UART0_Error_IRQHandler ; 43: UART0 error interrupt
- DCD UART0_IRQHandler ; 44: UART0 interrupt
- DCD UARTRX1_Handler ; 45: UART0 receive FIFO interrupt
- DCD UARTTX1_Handler ; 46: UART0 transmit FIFO interrupt
- DCD UART1_RxTimeout_IRQHandler ; 47: UART0 receive timeout interrupt
- DCD UART1_ModemStatus_IRQHandler ; 48: UART0 modem status interrupt
- DCD UART1_Error_IRQHandler ; 49: UART0 error interrupt
- DCD UART1_IRQHandler ; 50: UART0 interrupt
- DCD GPIO_0_IRQHandler ; 51: GPIO 0 interrupt
- DCD GPIO_1_IRQHandler ; 52: GPIO 1 interrupt
- DCD GPIO_2_IRQHandler ; 53: GPIO 2 interrupt
- DCD GPIO_3_IRQHandler ; 54: GPIO 3 interrupt
- DCD GPIO_4_IRQHandler ; 55: GPIO 4 interrupt
- DCD GPIO_5_IRQHandler ; 56: GPIO 5 interrupt
- DCD GPIO_6_IRQHandler ; 57: GPIO 6 interrupt
- DCD GPIO_7_IRQHandler ; 58: GPIO 7 interrupt
- DCD GPIO_8_IRQHandler ; 59: GPIO 8 interrupt
- DCD GPIO_9_IRQHandler ; 60: GPIO 9 interrupt
- DCD GPIO_10_IRQHandler ; 61: GPIO 10 interrupt
- DCD GPIO_11_IRQHandler ; 62: GPIO 11 interrupt
- DCD GPIO_12_IRQHandler ; 63: GPIO 12 interrupt
- DCD GPIO_13_IRQHandler ; 64: GPIO 13 interrupt
- DCD GPIO_14_IRQHandler ; 65: GPIO 14 interrupt
- DCD GPIO_15_IRQHandler ; 66: GPIO 15 interrupt
- DCD Combined_IRQHandler ; 67: Combined interrupt
- DCD PVT_IRQHandler ; 68: PVT sensor interrupt
- DCD 0 ; 69: Reserved
- DCD PWM_0_IRQHandler ; 70: PWM0 interrupt
- DCD RTC_IRQHandler ; 71: RTC interrupt
- DCD GpTimer0_IRQHandler ; 72: General Purpose Timer0
- DCD GpTimer1_IRQHandler ; 73: General Purpose Timer1
- DCD PWM_1_IRQHandler ; 74: PWM1 interrupt
- DCD PWM_2_IRQHandler ; 75: PWM2 interrupt
- DCD IOMUX_IRQHandler ; 76: IOMUX interrupt
-
-__Vectors_End
-
-__Vectors EQU __vector_table
-__Vectors_Size EQU __Vectors_End - __Vectors
-
-; Reset Handler
- PUBWEAK Reset_Handler
- SECTION .text:CODE:REORDER:NOROOT(2)
-Reset_Handler
- CPSID i ; Disable IRQs
- LDR R0, =SystemInit
- BLX R0
- LDR R0, =__iar_program_start
- BX R0
-End_Of_Main
- B .
-
-
-; Dummy Exception Handlers (infinite loops which can be modified)
-Default_Handler MACRO handler_name
- PUBWEAK handler_name
-handler_name
- B .
- ENDM
-
- Default_Handler NMI_Handler
- Default_Handler HardFault_Handler
- Default_Handler MemManage_Handler
- Default_Handler BusFault_Handler
- Default_Handler UsageFault_Handler
- Default_Handler SecureFault_Handler
- Default_Handler SVC_Handler
- Default_Handler DebugMon_Handler
- Default_Handler PendSV_Handler
- Default_Handler SysTick_Handler
-
- Default_Handler NS_WATCHDOG_RESET_IRQHandler
- Default_Handler NS_WATCHDOG_IRQHandler
- Default_Handler S32K_TIMER_IRQHandler
- Default_Handler TIMER0_IRQHandler
- Default_Handler TIMER1_IRQHandler
- Default_Handler DUALTIMER_IRQHandler
- Default_Handler MHU0_IRQHandler
- Default_Handler MHU1_IRQHandler
- Default_Handler CRYPTOCELL_IRQHandler
- Default_Handler MPC_Handler
- Default_Handler PPC_Handler
- Default_Handler S_MSC_COMBINED_IRQHandler
- Default_Handler S_BRIDGE_ERR_IRQHandler
- Default_Handler I_CACHE_INV_ERR_IRQHandler
- Default_Handler SYS_PPU_IRQHandler
- Default_Handler CPU0_PPU_IRQHandler
- Default_Handler CPU1_PPU_IRQHandler
- Default_Handler CPU0_DGB_PPU_IRQHandler
- Default_Handler CPU1_DGB_PPU_IRQHandler
- Default_Handler CRYPTOCELL_PPU_IRQHandler
- Default_Handler RAM0_PPU_IRQHandler
- Default_Handler RAM1_PPU_IRQHandler
- Default_Handler RAM2_PPU_IRQHandler
- Default_Handler RAM3_PPU_IRQHandler
- Default_Handler DEBUG_PPU_IRQHandler
- Default_Handler CPU0_CTI_IRQHandler
- Default_Handler CPU1_CTI_IRQHandler
-
- Default_Handler GpTimer_IRQHandler
- Default_Handler I2C0_IRQHandler
- Default_Handler I2C1_IRQHandler
- Default_Handler I2S_IRQHandler
- Default_Handler SPI_IRQHandler
- Default_Handler QSPI_IRQHandler
- Default_Handler UARTRX0_Handler
- Default_Handler UARTTX0_Handler
- Default_Handler UART0_RxTimeout_IRQHandler
- Default_Handler UART0_ModemStatus_IRQHandler
- Default_Handler UART0_Error_IRQHandler
- Default_Handler UART0_IRQHandler
- Default_Handler UARTRX1_Handler
- Default_Handler UARTTX1_Handler
- Default_Handler UART1_RxTimeout_IRQHandler
- Default_Handler UART1_ModemStatus_IRQHandler
- Default_Handler UART1_Error_IRQHandler
- Default_Handler UART1_IRQHandler
- Default_Handler GPIO_0_IRQHandler
- Default_Handler GPIO_1_IRQHandler
- Default_Handler GPIO_2_IRQHandler
- Default_Handler GPIO_3_IRQHandler
- Default_Handler GPIO_4_IRQHandler
- Default_Handler GPIO_5_IRQHandler
- Default_Handler GPIO_6_IRQHandler
- Default_Handler GPIO_7_IRQHandler
- Default_Handler GPIO_8_IRQHandler
- Default_Handler GPIO_9_IRQHandler
- Default_Handler GPIO_10_IRQHandler
- Default_Handler GPIO_11_IRQHandler
- Default_Handler GPIO_12_IRQHandler
- Default_Handler GPIO_13_IRQHandler
- Default_Handler GPIO_14_IRQHandler
- Default_Handler GPIO_15_IRQHandler
- Default_Handler Combined_IRQHandler
- Default_Handler PVT_IRQHandler
- Default_Handler PWM_0_IRQHandler
- Default_Handler RTC_IRQHandler
- Default_Handler GpTimer0_IRQHandler
- Default_Handler GpTimer1_IRQHandler
- Default_Handler PWM_1_IRQHandler
- Default_Handler PWM_2_IRQHandler
- Default_Handler IOMUX_IRQHandler
-
- END
diff --git a/platform/ext/target/musca_a/Device/Source/iar/startup_cmsdk_musca_ns.s b/platform/ext/target/musca_a/Device/Source/iar/startup_cmsdk_musca_ns.s
deleted file mode 100644
index fbcc409..0000000
--- a/platform/ext/target/musca_a/Device/Source/iar/startup_cmsdk_musca_ns.s
+++ /dev/null
@@ -1,247 +0,0 @@
-;/*
-; * Copyright (c) 2017-2020 ARM Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-;
-; This file is derivative of CMSIS V5.01 startup_ARMv8MML.s
-; Git SHA: 8a1d9d6ee18b143ae5befefa14d89fb5b3f99c75
-
-; <h> Stack Configuration
-; <o> Stack Size (in Bytes) <0x0-0xFFFFFFFF:8>
-; </h>
-; */
-
- MODULE ?cstartup
-
- ;; Forward declaration of sections.
- SECTION ARM_LIB_STACK_MSP:DATA:NOROOT(3)
- SECTION ARM_LIB_STACK:DATA:NOROOT(3)
-
- SECTION .intvec:CODE:NOROOT(2)
-
- EXTERN __iar_program_start
- EXTERN SystemInit
- PUBLIC __vector_table
- PUBLIC __Vectors
- PUBLIC __Vectors_End
- PUBLIC __Vectors_Size
-
- DATA
-
-__vector_table ;Core Interrupts
- DCD sfe(ARM_LIB_STACK_MSP) ; Top of Stack
- DCD Reset_Handler ; Reset Handler
- DCD NMI_Handler ; NMI Handler
- DCD HardFault_Handler ; Hard Fault Handler
- DCD MemManage_Handler ; MPU Fault Handler
- DCD BusFault_Handler ; Bus Fault Handler
- DCD UsageFault_Handler ; Usage Fault Handler
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD SVC_Handler ; SVCall Handler
- DCD DebugMon_Handler ; Debug Monitor Handler
- DCD 0 ; Reserved
- DCD PendSV_Handler ; PendSV Handler
- DCD SysTick_Handler ; SysTick Handler
- ;SSE-200 Interrupts
- DCD NS_WATCHDOG_RESET_IRQHandler ; 0: Non-Secure Watchdog Reset Request Interrupt
- DCD NS_WATCHDOG_IRQHandler ; 1: Non-Secure Watchdog Interrupt
- DCD S32K_TIMER_IRQHandler ; 2: S32K Timer Interrupt
- DCD TIMER0_IRQHandler ; 3: CMSDK Timer 0 Interrupt
- DCD TIMER1_Handler ; 4: CMSDK Timer 1 Interrupt
- DCD DUALTIMER_IRQHandler ; 5: CMSDK Dual Timer Interrupt
- DCD MHU0_IRQHandler ; 6: Message Handling Unit 0 Interrupt
- DCD MHU1_IRQHandler ; 7: Message Handling Unit 1 Interrupt
- DCD CRYPTOCELL_IRQHandler ; 8: CryptoCell-312 Interrupt
- DCD 0 ; 9: Reserved
- DCD 0 ; 10: Reserved
- DCD 0 ; 11: Reserved
- DCD 0 ; 12: Reserved
- DCD I_CACHE_INV_ERR_IRQHandler ; 13: Intsruction Cache Invalidation Interrupt
- DCD 0 ; 14: Reserved
- DCD SYS_PPU_IRQHandler ; 15: System PPU Interrupt
- DCD CPU0_PPU_IRQHandler ; 16: CPU0 PPU Interrupt
- DCD CPU1_PPU_IRQHandler ; 17: CPU1 PPU Interrupt
- DCD CPU0_DGB_PPU_IRQHandler ; 18: CPU0 Debug PPU Interrupt
- DCD CPU1_DGB_PPU_IRQHandler ; 19: CPU1 Debug PPU Interrupt
- DCD CRYPTOCELL_PPU_IRQHandler ; 20: CryptoCell PPU Interrupt
- DCD 0 ; 21: Reserved
- DCD RAM0_PPU_IRQHandler ; 22: RAM 0 PPU Interrupt
- DCD RAM1_PPU_IRQHandler ; 23: RAM 1 PPU Interrupt
- DCD RAM2_PPU_IRQHandler ; 24: RAM 2 PPU Interrupt
- DCD RAM3_PPU_IRQHandler ; 25: RAM 3 PPU Interrupt
- DCD DEBUG_PPU_IRQHandler ; 26: Debug PPU Interrupt
- DCD 0 ; 27: Reserved
- DCD CPU0_CTI_IRQHandler ; 28: CPU0 CTI Interrupt
- DCD CPU1_CTI_IRQHandler ; 29: CPU1 CTI Interrupt
- DCD 0 ; 30: Reserved
- DCD 0 ; 31: Reserved
- ;Expansion Interrupts
- DCD 0 ; 32: Reserved
- DCD GpTimer_IRQHandler ; 33: General Purpose Timer
- DCD I2C0_IRQHandler ; 34: I2C0
- DCD I2C1_IRQHandler ; 35: I2C1
- DCD I2S_IRQHandler ; 36: I2S
- DCD SPI_IRQHandler ; 37: SPI
- DCD QSPI_IRQHandler ; 38: QSPI
- DCD UARTRX0_Handler ; 39: UART0 receive FIFO interrupt
- DCD UARTTX0_Handler ; 40: UART0 transmit FIFO interrupt
- DCD UART0_RxTimeout_IRQHandler ; 41: UART0 receive timeout interrupt
- DCD UART0_ModemStatus_IRQHandler ; 42: UART0 modem status interrupt
- DCD UART0_Error_IRQHandler ; 43: UART0 error interrupt
- DCD UART0_IRQHandler ; 44: UART0 interrupt
- DCD UARTRX1_Handler ; 45: UART0 receive FIFO interrupt
- DCD UARTTX1_Handler ; 46: UART0 transmit FIFO interrupt
- DCD UART1_RxTimeout_IRQHandler ; 47: UART0 receive timeout interrupt
- DCD UART1_ModemStatus_IRQHandler ; 48: UART0 modem status interrupt
- DCD UART1_Error_IRQHandler ; 49: UART0 error interrupt
- DCD UART1_IRQHandler ; 50: UART0 interrupt
- DCD GPIO_0_IRQHandler ; 51: GPIO 0 interrupt
- DCD GPIO_1_IRQHandler ; 52: GPIO 1 interrupt
- DCD GPIO_2_IRQHandler ; 53: GPIO 2 interrupt
- DCD GPIO_3_IRQHandler ; 54: GPIO 3 interrupt
- DCD GPIO_4_IRQHandler ; 55: GPIO 4 interrupt
- DCD GPIO_5_IRQHandler ; 56: GPIO 5 interrupt
- DCD GPIO_6_IRQHandler ; 57: GPIO 6 interrupt
- DCD GPIO_7_IRQHandler ; 58: GPIO 7 interrupt
- DCD GPIO_8_IRQHandler ; 59: GPIO 8 interrupt
- DCD GPIO_9_IRQHandler ; 60: GPIO 9 interrupt
- DCD GPIO_10_IRQHandler ; 61: GPIO 10 interrupt
- DCD GPIO_11_IRQHandler ; 62: GPIO 11 interrupt
- DCD GPIO_12_IRQHandler ; 63: GPIO 12 interrupt
- DCD GPIO_13_IRQHandler ; 64: GPIO 13 interrupt
- DCD GPIO_14_IRQHandler ; 65: GPIO 14 interrupt
- DCD GPIO_15_IRQHandler ; 66: GPIO 15 interrupt
- DCD Combined_IRQHandler ; 67: Combined interrupt
- DCD PVT_IRQHandler ; 68: PVT sensor interrupt
- DCD 0 ; 69: Reserved
- DCD PWM_0_IRQHandler ; 70: PWM0 interrupt
- DCD RTC_IRQHandler ; 71: RTC interrupt
- DCD GpTimer0_IRQHandler ; 72: General Purpose Timer0
- DCD GpTimer1_IRQHandler ; 73: General Purpose Timer1
- DCD PWM_1_IRQHandler ; 74: PWM1 interrupt
- DCD PWM_2_IRQHandler ; 75: PWM2 interrupt
- DCD IOMUX_IRQHandler ; 76: IOMUX interrupt
-
-__Vectors_End
-
-__Vectors EQU __vector_table
-__Vectors_Size EQU __Vectors_End - __Vectors
-
-; Reset Handler
-
- PUBWEAK Reset_Handler
- SECTION .text:CODE:REORDER:NOROOT(2)
-Reset_Handler
- LDR R0, =SystemInit
- BLX R0
- LDR R0, =sfe(ARM_LIB_STACK) ; End of ARM_LIB_STACK
- MSR PSP, R0
- MRS R0, CONTROL ; Get control value
- ORR R0, R0, #1 ; Select switch to non privileged mode
- ORR R0, R0, #2 ; Select switch to PSP
- MSR CONTROL, R0
- LDR R0, =__iar_program_start
- BX R0
-End_Of_Main
- B .
-
-
-; Dummy Exception Handlers (infinite loops which can be modified)
-Default_Handler MACRO handler_name
- PUBWEAK handler_name
-handler_name
- B .
- ENDM
-
- Default_Handler NMI_Handler
- Default_Handler HardFault_Handler
- Default_Handler MemManage_Handler
- Default_Handler BusFault_Handler
- Default_Handler UsageFault_Handler
- Default_Handler SVC_Handler
- Default_Handler DebugMon_Handler
- Default_Handler PendSV_Handler
- Default_Handler SysTick_Handler
-
- Default_Handler NS_WATCHDOG_RESET_IRQHandler
- Default_Handler NS_WATCHDOG_IRQHandler
- Default_Handler S32K_TIMER_IRQHandler
- Default_Handler TIMER0_IRQHandler
- Default_Handler TIMER1_Handler
- Default_Handler DUALTIMER_IRQHandler
- Default_Handler MHU0_IRQHandler
- Default_Handler MHU1_IRQHandler
- Default_Handler CRYPTOCELL_IRQHandler
- Default_Handler I_CACHE_INV_ERR_IRQHandler
- Default_Handler SYS_PPU_IRQHandler
- Default_Handler CPU0_PPU_IRQHandler
- Default_Handler CPU1_PPU_IRQHandler
- Default_Handler CPU0_DGB_PPU_IRQHandler
- Default_Handler CPU1_DGB_PPU_IRQHandler
- Default_Handler CRYPTOCELL_PPU_IRQHandler
- Default_Handler RAM0_PPU_IRQHandler
- Default_Handler RAM1_PPU_IRQHandler
- Default_Handler RAM2_PPU_IRQHandler
- Default_Handler RAM3_PPU_IRQHandler
- Default_Handler DEBUG_PPU_IRQHandler
- Default_Handler CPU0_CTI_IRQHandler
- Default_Handler CPU1_CTI_IRQHandler
-
- Default_Handler GpTimer_IRQHandler
- Default_Handler I2C0_IRQHandler
- Default_Handler I2C1_IRQHandler
- Default_Handler I2S_IRQHandler
- Default_Handler SPI_IRQHandler
- Default_Handler QSPI_IRQHandler
- Default_Handler UARTRX0_Handler
- Default_Handler UARTTX0_Handler
- Default_Handler UART0_RxTimeout_IRQHandler
- Default_Handler UART0_ModemStatus_IRQHandler
- Default_Handler UART0_Error_IRQHandler
- Default_Handler UART0_IRQHandler
- Default_Handler UARTRX1_Handler
- Default_Handler UARTTX1_Handler
- Default_Handler UART1_RxTimeout_IRQHandler
- Default_Handler UART1_ModemStatus_IRQHandler
- Default_Handler UART1_Error_IRQHandler
- Default_Handler UART1_IRQHandler
- Default_Handler GPIO_0_IRQHandler
- Default_Handler GPIO_1_IRQHandler
- Default_Handler GPIO_2_IRQHandler
- Default_Handler GPIO_3_IRQHandler
- Default_Handler GPIO_4_IRQHandler
- Default_Handler GPIO_5_IRQHandler
- Default_Handler GPIO_6_IRQHandler
- Default_Handler GPIO_7_IRQHandler
- Default_Handler GPIO_8_IRQHandler
- Default_Handler GPIO_9_IRQHandler
- Default_Handler GPIO_10_IRQHandler
- Default_Handler GPIO_11_IRQHandler
- Default_Handler GPIO_12_IRQHandler
- Default_Handler GPIO_13_IRQHandler
- Default_Handler GPIO_14_IRQHandler
- Default_Handler GPIO_15_IRQHandler
- Default_Handler Combined_IRQHandler
- Default_Handler PVT_IRQHandler
- Default_Handler PWM_0_IRQHandler
- Default_Handler RTC_IRQHandler
- Default_Handler GpTimer0_IRQHandler
- Default_Handler GpTimer1_IRQHandler
- Default_Handler PWM_1_IRQHandler
- Default_Handler PWM_2_IRQHandler
- Default_Handler IOMUX_IRQHandler
-
- END
diff --git a/platform/ext/target/musca_a/Device/Source/iar/startup_cmsdk_musca_s.s b/platform/ext/target/musca_a/Device/Source/iar/startup_cmsdk_musca_s.s
deleted file mode 100644
index 439eecf..0000000
--- a/platform/ext/target/musca_a/Device/Source/iar/startup_cmsdk_musca_s.s
+++ /dev/null
@@ -1,256 +0,0 @@
-;/*
-; * Copyright (c) 2017-2020 ARM Limited
-; *
-; * Licensed under the Apache License, Version 2.0 (the "License");
-; * you may not use this file except in compliance with the License.
-; * You may obtain a copy of the License at
-; *
-; * http://www.apache.org/licenses/LICENSE-2.0
-; *
-; * Unless required by applicable law or agreed to in writing, software
-; * distributed under the License is distributed on an "AS IS" BASIS,
-; * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-; * See the License for the specific language governing permissions and
-; * limitations under the License.
-; */
-;
-; This file is derivative of CMSIS V5.01 startup_ARMv8MML.s
-; Git SHA: 8a1d9d6ee18b143ae5befefa14d89fb5b3f99c75
-
-;/*
-;//-------- <<< Use Configuration Wizard in Context Menu >>> ------------------
-;*/
-
-
-; <h> Stack Configuration
-; <o> Stack Size (in Bytes) <0x0-0xFFFFFFFF:8>
-; </h>
-
- MODULE ?cstartup
-
- ;; Forward declaration of sections.
- SECTION ARM_LIB_STACK_MSP:DATA:NOROOT(3)
- SECTION ARM_LIB_STACK:DATA:NOROOT(3)
-
- SECTION .intvec:CODE:NOROOT(2)
-
- EXTERN __iar_program_start
- EXTERN SystemInit
- PUBLIC __vector_table
- PUBLIC __Vectors
- PUBLIC __Vectors_End
- PUBLIC __Vectors_Size
-
- DATA
-
-__vector_table ;Core Interrupts
- DCD sfe(ARM_LIB_STACK_MSP) ; Top of Stack
- DCD Reset_Handler ; Reset Handler
- DCD NMI_Handler ; NMI Handler
- DCD HardFault_Handler ; Hard Fault Handler
- DCD MemManage_Handler ; MPU Fault Handler
- DCD BusFault_Handler ; Bus Fault Handler
- DCD UsageFault_Handler ; Usage Fault Handler
- DCD SecureFault_Handler ; Secure Fault Handler
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD 0 ; Reserved
- DCD SVC_Handler ; SVCall Handler
- DCD DebugMon_Handler ; Debug Monitor Handler
- DCD 0 ; Reserved
- DCD PendSV_Handler ; PendSV Handler
- DCD SysTick_Handler ; SysTick Handler
- ;SSE-200 Interrupts
- DCD NS_WATCHDOG_RESET_IRQHandler ; 0: Non-Secure Watchdog Reset Request Interrupt
- DCD NS_WATCHDOG_IRQHandler ; 1: Non-Secure Watchdog Interrupt
- DCD S32K_TIMER_IRQHandler ; 2: S32K Timer Interrupt
- DCD TFM_TIMER0_IRQ_Handler ; 3: CMSDK Timer 0 Interrupt
- DCD TIMER1_IRQHandler ; 4: CMSDK Timer 1 Interrupt
- DCD DUALTIMER_IRQHandler ; 5: CMSDK Dual Timer Interrupt
- DCD MHU0_IRQHandler ; 6: Message Handling Unit 0 Interrupt
- DCD MHU1_IRQHandler ; 7: Message Handling Unit 1 Interrupt
- DCD CRYPTOCELL_IRQHandler ; 8: CryptoCell-312 Interrupt
- DCD MPC_Handler ; 9: Secure Combined MPC Interrupt
- DCD PPC_Handler ; 10: Secure Combined PPC Interrupt
- DCD S_MSC_COMBINED_IRQHandler ; 11: Secure Combined MSC Interrupt
- DCD S_BRIDGE_ERR_IRQHandler ; 12: Secure Bridge Error Combined Interrupt
- DCD I_CACHE_INV_ERR_IRQHandler ; 13: Intsruction Cache Invalidation Interrupt
- DCD 0 ; 14: Reserved
- DCD SYS_PPU_IRQHandler ; 15: System PPU Interrupt
- DCD CPU0_PPU_IRQHandler ; 16: CPU0 PPU Interrupt
- DCD CPU1_PPU_IRQHandler ; 17: CPU1 PPU Interrupt
- DCD CPU0_DGB_PPU_IRQHandler ; 18: CPU0 Debug PPU Interrupt
- DCD CPU1_DGB_PPU_IRQHandler ; 19: CPU1 Debug PPU Interrupt
- DCD CRYPTOCELL_PPU_IRQHandler ; 20: CryptoCell PPU Interrupt
- DCD 0 ; 21: Reserved
- DCD RAM0_PPU_IRQHandler ; 22: RAM 0 PPU Interrupt
- DCD RAM1_PPU_IRQHandler ; 23: RAM 1 PPU Interrupt
- DCD RAM2_PPU_IRQHandler ; 24: RAM 2 PPU Interrupt
- DCD RAM3_PPU_IRQHandler ; 25: RAM 3 PPU Interrupt
- DCD DEBUG_PPU_IRQHandler ; 26: Debug PPU Interrupt
- DCD 0 ; 27: Reserved
- DCD CPU0_CTI_IRQHandler ; 28: CPU0 CTI Interrupt
- DCD CPU1_CTI_IRQHandler ; 29: CPU1 CTI Interrupt
- DCD 0 ; 30: Reserved
- DCD 0 ; 31: Reserved
- ;Expansion Interrupts
- DCD 0 ; 32: Reserved
- DCD GpTimer_IRQHandler ; 33: General Purpose Timer
- DCD I2C0_IRQHandler ; 34: I2C0
- DCD I2C1_IRQHandler ; 35: I2C1
- DCD I2S_IRQHandler ; 36: I2S
- DCD SPI_IRQHandler ; 37: SPI
- DCD QSPI_IRQHandler ; 38: QSPI
- DCD UARTRX0_Handler ; 39: UART0 receive FIFO interrupt
- DCD UARTTX0_Handler ; 40: UART0 transmit FIFO interrupt
- DCD UART0_RxTimeout_IRQHandler ; 41: UART0 receive timeout interrupt
- DCD UART0_ModemStatus_IRQHandler ; 42: UART0 modem status interrupt
- DCD UART0_Error_IRQHandler ; 43: UART0 error interrupt
- DCD UART0_IRQHandler ; 44: UART0 interrupt
- DCD UARTRX1_Handler ; 45: UART0 receive FIFO interrupt
- DCD UARTTX1_Handler ; 46: UART0 transmit FIFO interrupt
- DCD UART1_RxTimeout_IRQHandler ; 47: UART0 receive timeout interrupt
- DCD UART1_ModemStatus_IRQHandler ; 48: UART0 modem status interrupt
- DCD UART1_Error_IRQHandler ; 49: UART0 error interrupt
- DCD UART1_IRQHandler ; 50: UART0 interrupt
- DCD GPIO_0_IRQHandler ; 51: GPIO 0 interrupt
- DCD GPIO_1_IRQHandler ; 52: GPIO 1 interrupt
- DCD GPIO_2_IRQHandler ; 53: GPIO 2 interrupt
- DCD GPIO_3_IRQHandler ; 54: GPIO 3 interrupt
- DCD GPIO_4_IRQHandler ; 55: GPIO 4 interrupt
- DCD GPIO_5_IRQHandler ; 56: GPIO 5 interrupt
- DCD GPIO_6_IRQHandler ; 57: GPIO 6 interrupt
- DCD GPIO_7_IRQHandler ; 58: GPIO 7 interrupt
- DCD GPIO_8_IRQHandler ; 59: GPIO 8 interrupt
- DCD GPIO_9_IRQHandler ; 60: GPIO 9 interrupt
- DCD GPIO_10_IRQHandler ; 61: GPIO 10 interrupt
- DCD GPIO_11_IRQHandler ; 62: GPIO 11 interrupt
- DCD GPIO_12_IRQHandler ; 63: GPIO 12 interrupt
- DCD GPIO_13_IRQHandler ; 64: GPIO 13 interrupt
- DCD GPIO_14_IRQHandler ; 65: GPIO 14 interrupt
- DCD GPIO_15_IRQHandler ; 66: GPIO 15 interrupt
- DCD Combined_IRQHandler ; 67: Combined interrupt
- DCD PVT_IRQHandler ; 68: PVT sensor interrupt
- DCD 0 ; 69: Reserved
- DCD PWM_0_IRQHandler ; 70: PWM0 interrupt
- DCD RTC_IRQHandler ; 71: RTC interrupt
- DCD GpTimer0_IRQHandler ; 72: General Purpose Timer0
- DCD GpTimer1_IRQHandler ; 73: General Purpose Timer1
- DCD PWM_1_IRQHandler ; 74: PWM1 interrupt
- DCD PWM_2_IRQHandler ; 75: PWM2 interrupt
- DCD IOMUX_IRQHandler ; 76: IOMUX interrupt
-
-__Vectors_End
-
-__Vectors EQU __vector_table
-__Vectors_Size EQU __Vectors_End - __Vectors
-
-; Reset Handler
- PUBWEAK Reset_Handler
- SECTION .text:CODE:REORDER:NOROOT(2)
-Reset_Handler
- CPSID i ; Disable IRQs
- LDR R0, =SystemInit
- BLX R0
- LDR R0, =sfe(ARM_LIB_STACK) ; End of PROC_STACK
- MSR PSP, R0
- MRS R0, control ; Get control value
- ORR R0, R0, #2 ; Select switch to PSP
- MSR control, R0
- LDR R0, =__iar_program_start
- BX R0
-End_Of_Main
- B .
-
-
-; Dummy Exception Handlers (infinite loops which can be modified)
-Default_Handler MACRO handler_name
- PUBWEAK handler_name
-handler_name
- B .
- ENDM
-
- Default_Handler NMI_Handler
- Default_Handler HardFault_Handler
- Default_Handler MemManage_Handler
- Default_Handler BusFault_Handler
- Default_Handler UsageFault_Handler
- Default_Handler SecureFault_Handler
- Default_Handler SVC_Handler
- Default_Handler DebugMon_Handler
- Default_Handler PendSV_Handler
- Default_Handler SysTick_Handler
-
- Default_Handler NS_WATCHDOG_RESET_IRQHandler
- Default_Handler NS_WATCHDOG_IRQHandler
- Default_Handler S32K_TIMER_IRQHandler
- Default_Handler TFM_TIMER0_IRQ_Handler
- Default_Handler TIMER1_IRQHandler
- Default_Handler DUALTIMER_IRQHandler
- Default_Handler MHU0_IRQHandler
- Default_Handler MHU1_IRQHandler
- Default_Handler CRYPTOCELL_IRQHandler
- Default_Handler MPC_Handler
- Default_Handler PPC_Handler
- Default_Handler S_MSC_COMBINED_IRQHandler
- Default_Handler S_BRIDGE_ERR_IRQHandler
- Default_Handler I_CACHE_INV_ERR_IRQHandler
- Default_Handler SYS_PPU_IRQHandler
- Default_Handler CPU0_PPU_IRQHandler
- Default_Handler CPU1_PPU_IRQHandler
- Default_Handler CPU0_DGB_PPU_IRQHandler
- Default_Handler CPU1_DGB_PPU_IRQHandler
- Default_Handler CRYPTOCELL_PPU_IRQHandler
- Default_Handler RAM0_PPU_IRQHandler
- Default_Handler RAM1_PPU_IRQHandler
- Default_Handler RAM2_PPU_IRQHandler
- Default_Handler RAM3_PPU_IRQHandler
- Default_Handler DEBUG_PPU_IRQHandler
- Default_Handler CPU0_CTI_IRQHandler
- Default_Handler CPU1_CTI_IRQHandler
-
- Default_Handler GpTimer_IRQHandler
- Default_Handler I2C0_IRQHandler
- Default_Handler I2C1_IRQHandler
- Default_Handler I2S_IRQHandler
- Default_Handler SPI_IRQHandler
- Default_Handler QSPI_IRQHandler
- Default_Handler UARTRX0_Handler
- Default_Handler UARTTX0_Handler
- Default_Handler UART0_RxTimeout_IRQHandler
- Default_Handler UART0_ModemStatus_IRQHandler
- Default_Handler UART0_Error_IRQHandler
- Default_Handler UART0_IRQHandler
- Default_Handler UARTRX1_Handler
- Default_Handler UARTTX1_Handler
- Default_Handler UART1_RxTimeout_IRQHandler
- Default_Handler UART1_ModemStatus_IRQHandler
- Default_Handler UART1_Error_IRQHandler
- Default_Handler UART1_IRQHandler
- Default_Handler GPIO_0_IRQHandler
- Default_Handler GPIO_1_IRQHandler
- Default_Handler GPIO_2_IRQHandler
- Default_Handler GPIO_3_IRQHandler
- Default_Handler GPIO_4_IRQHandler
- Default_Handler GPIO_5_IRQHandler
- Default_Handler GPIO_6_IRQHandler
- Default_Handler GPIO_7_IRQHandler
- Default_Handler GPIO_8_IRQHandler
- Default_Handler GPIO_9_IRQHandler
- Default_Handler GPIO_10_IRQHandler
- Default_Handler GPIO_11_IRQHandler
- Default_Handler GPIO_12_IRQHandler
- Default_Handler GPIO_13_IRQHandler
- Default_Handler GPIO_14_IRQHandler
- Default_Handler GPIO_15_IRQHandler
- Default_Handler Combined_IRQHandler
- Default_Handler PVT_IRQHandler
- Default_Handler PWM_0_IRQHandler
- Default_Handler RTC_IRQHandler
- Default_Handler GpTimer0_IRQHandler
- Default_Handler GpTimer1_IRQHandler
- Default_Handler PWM_1_IRQHandler
- Default_Handler PWM_2_IRQHandler
- Default_Handler IOMUX_IRQHandler
-
- END
diff --git a/platform/ext/target/musca_a/Device/Source/system_core_init.c b/platform/ext/target/musca_a/Device/Source/system_core_init.c
deleted file mode 100644
index f08696f..0000000
--- a/platform/ext/target/musca_a/Device/Source/system_core_init.c
+++ /dev/null
@@ -1,68 +0,0 @@
-/*
- * Copyright (c) 2009-2020 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- *
- * This file is derivative of CMSIS V5.01 \Device\ARM\ARMCM33\Source\system_ARMCM33.c
- * https://github.com/ARM-software/CMSIS_5/tree/5.0.1
- * Git SHA: 8a1d9d6ee18b143ae5befefa14d89fb5b3f99c75
- */
-
-#include <stdint.h>
-#include "system_core_init.h"
-#include "platform_description.h"
-
-/*----------------------------------------------------------------------------
- Define clocks
- *----------------------------------------------------------------------------*/
-#define XTAL (50000000UL)
-#define SYSTEM_CLOCK (XTAL)
-#define SYSTEM_REFCLK (32768UL)
-
-/*----------------------------------------------------------------------------
- Externals
- *----------------------------------------------------------------------------*/
-
-/*----------------------------------------------------------------------------
- System Core Clock Variable
- *----------------------------------------------------------------------------*/
-uint32_t SystemCoreClock = SYSTEM_CLOCK;
-uint32_t PeripheralClock = SYSTEM_CLOCK;
-uint32_t RefClock = SYSTEM_REFCLK;
-
-/*----------------------------------------------------------------------------
- System Core Clock update function
- *----------------------------------------------------------------------------*/
-void SystemCoreClockUpdate (void)
-{
- SystemCoreClock = SYSTEM_CLOCK;
- PeripheralClock = SYSTEM_CLOCK;
- RefClock = SYSTEM_REFCLK;
-}
-
-/*----------------------------------------------------------------------------
- System initialization function
- *----------------------------------------------------------------------------*/
-void SystemInit (void)
-{
-#if defined (__VTOR_PRESENT) && (__VTOR_PRESENT == 1U)
- extern uint32_t __Vectors;
- SCB->VTOR = (uint32_t) &__Vectors;
-#endif
-
-#ifdef UNALIGNED_SUPPORT_DISABLE
- SCB->CCR |= SCB_CCR_UNALIGN_TRP_Msk;
-#endif
-
- SystemCoreClock = SYSTEM_CLOCK;
-}
diff --git a/platform/ext/target/musca_a/Libraries/mt25ql_flash_lib.c b/platform/ext/target/musca_a/Libraries/mt25ql_flash_lib.c
deleted file mode 100644
index f748ecf..0000000
--- a/platform/ext/target/musca_a/Libraries/mt25ql_flash_lib.c
+++ /dev/null
@@ -1,901 +0,0 @@
-/*
- * Copyright (c) 2018-2020 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include <stdlib.h>
-/* Use memcpy function */
-#include <string.h>
-
-#include "mt25ql_flash_lib.h"
-#include "qspi_ip6514e_drv.h"
-
-/** Setter bit manipulation macro */
-#define SET_BIT(WORD, BIT_INDEX) ((WORD) |= (1U << (BIT_INDEX)))
-/** Clearing bit manipulation macro */
-#define CLR_BIT(WORD, BIT_INDEX) ((WORD) &= ~(1U << (BIT_INDEX)))
-/** Getter bit manipulation macro */
-#define GET_BIT(WORD, BIT_INDEX) (bool)(((WORD) & (1U << (BIT_INDEX))))
-
-#define BITS_PER_WORD 32U
-#define BYTES_PER_WORD 4U
-
-#define ARG_NOT_USED 0
-#define ARG_PTR_NOT_USED NULL
-
-/** MT25QL used command */
-#define WRITE_ENABLE_CMD 0x06U
-#define READ_ENHANCED_VOLATILE_CFG_REG_CMD 0x65U
-#define WRITE_ENHANCED_VOLATILE_CFG_REG_CMD 0x61U
-#define READ_VOLATILE_CFG_REG_CMD 0x85U
-#define WRITE_VOLATILE_CFG_REG_CMD 0x81U
-#define READ_FLAG_STATUS_REG_CMD 0x70U
-#define SUBSECTOR_ERASE_32KB_CMD 0x52U
-#define SUBSECTOR_ERASE_4KB_CMD 0x20U
-#define SECTOR_ERASE_CMD 0xD8U
-#define BULK_ERASE_CMD 0xC7U
-/*
- * The baud rate divisor in \ref mt25ql_dev_t needs to be configured adequately
- * to handle those commands.
- */
-#define QUAD_OUTPUT_FAST_READ_CMD 0x6BU
-#define FAST_READ_CMD 0x0BU
-#define READ_CMD 0x03U
-#define QUAD_INPUT_FAST_PROGRAM_CMD 0x32U
-#define PAGE_PROGRAM_CMD 0x02U
-
-/** MT25QL Enhanced Volatile Configuration Register access */
-#define ENHANCED_VOLATILE_CFG_REG_LEN 1U
-#define ENHANCED_VOLATILE_CFG_REG_QSPI_POS 7U
-#define ENHANCED_VOLATILE_CFG_REG_DSPI_POS 6U
-
-/** MT25QL Volatile Configuration Register access */
-#define VOLATILE_CFG_REG_LEN 1U
-#define VOLATILE_CFG_REG_DUMMY_CYCLES_POS 4U
-#define VOLATILE_CFG_REG_DUMMY_CYCLES_BITS 4U
-
-/** MT25QL Flag Status Register access */
-#define FLAG_STATUS_REG_LEN 1U
-#define FLAG_STATUS_REG_READY_POS 7U
-
-/*
- * 10 is the minimal number of dummy clock cycles needed to reach the maximal
- * frequency of the Quad Output Fast Read Command.
- */
-#define QUAD_OUTPUT_FAST_READ_DUMMY_CYCLES 10U
-#define FAST_READ_DUMMY_CYCLES 8U
-#define RESET_STATE_DUMMY_CYCLES 8U
-#define DEFAULT_READ_DUMMY_CYCLES 0U
-#define QUAD_INPUT_FAST_PROGRAM_DUMMY_CYCLES 0U
-#define PAGE_PROGRAM_DUMMY_CYCLES 0U
-
-/* Only up to 8 bytes can be read or written using the Flash commands. */
-#define CMD_DATA_MAX_SIZE 8U
-
-/**
- * \brief Change specific bits in a 32 bits word.
- *
- * \param[in,out] word Pointer of the word to change
- * \param[in] bits bits_length bits to put at bits_pos in the word
- * pointed
- * \param[in] bits_length Number of bits to change
- * \param[in] bits_pos Position of the bits to change
- *
- * \note This function will do nothing if the parameters given are incorrect:
- * * word is NULL
- * * bits_length + bits_pos > 32
- * * bits_length is 0
- */
-static void change_bits_in_word(volatile uint32_t *word,
- uint32_t bits,
- uint32_t bits_length,
- uint32_t bits_pos)
-{
- uint32_t mask;
-
- if ((word == NULL) ||
- ((bits_length + bits_pos) > BITS_PER_WORD) ||
- (bits_length == 0U)) {
- /* Silently fail */
- return;
- }
-
- /* Change all the bits */
- if (bits_length == BITS_PER_WORD) {
- *word = bits;
- return;
- }
-
- mask = ((1U << bits_length) - 1);
- /*
- * We change the bits in three steps:
- * - clear bits_length bits with zeroes at bits_pos in the word
- * - mask bits in case it contains more than bits_length bits
- * - set the new bits in the cleared word
- * Because the data pointed by word is only read once, the data will still
- * be coherent after an interruption that changes it.
- */
- *word = ((*word & ~(mask << bits_pos)) | ((bits & mask) << bits_pos));
-}
-
-/**
- * \brief Send the Write Enable command, needed before any write.
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- */
-static void send_write_enable(struct mt25ql_dev_t* dev)
-{
- qspi_ip6514e_send_simple_cmd(dev->controller, WRITE_ENABLE_CMD);
-}
-
-/**
- * \brief Set SPI mode on the flash device and on the controller.
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- * \param[in] spi_mode SPI mode to be set on flash device and controller
- * \ref qspi_ip6514e_spi_mode_t
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- */
-static enum mt25ql_error_t set_spi_mode(struct mt25ql_dev_t* dev,
- enum qspi_ip6514e_spi_mode_t spi_mode)
-{
- uint8_t enhanced_volatile_cfg_reg = 0;
- enum qspi_ip6514e_error_t controller_error;
-
- /* Read the Enhanced Volatile Configuration Register, modify it according
- * to the requested SPI mode then write back the modified value to the
- * register. This will activate the SPI mode on the flash side.
- */
- controller_error = qspi_ip6514e_send_read_cmd(
- dev->controller,
- READ_ENHANCED_VOLATILE_CFG_REG_CMD,
- &enhanced_volatile_cfg_reg,
- ENHANCED_VOLATILE_CFG_REG_LEN,
- ARG_NOT_USED,
- ARG_NOT_USED,
- 0); /* No dummy cycles needed for
- this command. */
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- switch(spi_mode) {
- case QSPI_IP6514E_SPI_MODE:
- /* Disable the Dual- and Quad-SPI modes.
- * Clearing the bit enables the mode, setting it disables it.
- */
- SET_BIT(enhanced_volatile_cfg_reg, ENHANCED_VOLATILE_CFG_REG_DSPI_POS);
- SET_BIT(enhanced_volatile_cfg_reg, ENHANCED_VOLATILE_CFG_REG_QSPI_POS);
- break;
- case QSPI_IP6514E_DSPI_MODE:
- /* Disable the Quad-SPI mode and activate DSPI mode.
- * Clearing the bit enables the mode, setting it disables it.
- */
- CLR_BIT(enhanced_volatile_cfg_reg, ENHANCED_VOLATILE_CFG_REG_DSPI_POS);
- SET_BIT(enhanced_volatile_cfg_reg, ENHANCED_VOLATILE_CFG_REG_QSPI_POS);
- break;
- case QSPI_IP6514E_QSPI_MODE:
- /* Disable the Dual-SPI mode and activate QSPI mode.
- * Clearing the bit enables the mode, setting it disables it.
- */
- SET_BIT(enhanced_volatile_cfg_reg, ENHANCED_VOLATILE_CFG_REG_DSPI_POS);
- CLR_BIT(enhanced_volatile_cfg_reg, ENHANCED_VOLATILE_CFG_REG_QSPI_POS);
- break;
- default:
- return MT25QL_ERR_WRONG_ARGUMENT;
- }
-
- send_write_enable(dev);
-
- controller_error = qspi_ip6514e_send_write_cmd(
- dev->controller,
- WRITE_ENHANCED_VOLATILE_CFG_REG_CMD,
- &enhanced_volatile_cfg_reg,
- ENHANCED_VOLATILE_CFG_REG_LEN,
- ARG_NOT_USED,
- ARG_NOT_USED,
- 0); /* No dummy cycles needed for
- this command. */
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- /* Activate the requested SPI mode on the controller side as well. */
- controller_error = qspi_ip6514e_set_spi_mode(dev->controller,
- spi_mode,
- spi_mode,
- spi_mode);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- return MT25QL_ERR_NONE;
-}
-
-/**
- * \brief Change the number of dummy clock cycles subsequent to all FAST READ
- * commands.
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- * \param[in] dummy_cycles Dummy clock cycles to set
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- */
-static enum mt25ql_error_t change_dummy_cycles(struct mt25ql_dev_t* dev,
- uint32_t dummy_cycles)
-{
- uint32_t volatile_cfg_reg = 0;
- enum qspi_ip6514e_error_t controller_error;
-
- /*
- * Changes the number of dummy cycles in the Volatile Configuration
- * Register.
- */
- controller_error = qspi_ip6514e_send_read_cmd(dev->controller,
- READ_VOLATILE_CFG_REG_CMD,
- &volatile_cfg_reg,
- VOLATILE_CFG_REG_LEN,
- ARG_NOT_USED,
- ARG_NOT_USED,
- 0); /* No dummy cycles needed
- for this command. */
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- change_bits_in_word(&volatile_cfg_reg,
- dummy_cycles,
- VOLATILE_CFG_REG_DUMMY_CYCLES_BITS,
- VOLATILE_CFG_REG_DUMMY_CYCLES_POS);
-
- send_write_enable(dev);
-
- controller_error = qspi_ip6514e_send_write_cmd(dev->controller,
- WRITE_VOLATILE_CFG_REG_CMD,
- &volatile_cfg_reg,
- VOLATILE_CFG_REG_LEN,
- ARG_NOT_USED,
- ARG_NOT_USED,
- 0); /* No dummy cycles needed
- for this command. */
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- return MT25QL_ERR_NONE;
-}
-
-/**
- * \brief Wait until the current program/erase is finished.
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- */
-static enum mt25ql_error_t wait_program_or_erase_complete(
- struct mt25ql_dev_t* dev)
-{
- enum qspi_ip6514e_error_t controller_error;
- uint8_t flag_status_reg = 0;
-
- /* Wait until the ready bit of the Flag Status Register is set */
- while (!GET_BIT(flag_status_reg, FLAG_STATUS_REG_READY_POS)) {
- controller_error = qspi_ip6514e_send_read_cmd(dev->controller,
- READ_FLAG_STATUS_REG_CMD,
- &flag_status_reg,
- FLAG_STATUS_REG_LEN,
- ARG_NOT_USED,
- ARG_NOT_USED,
- 0); /* No dummy cycles
- needed for this
- command. */
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
- }
-
- return MT25QL_ERR_NONE;
-}
-
-/**
- * \brief Execute a program command that crosses the page size boundary.
- *
- * \param[in] dev Pointer to MT25QL device structure
- * \ref mt25ql_dev_t
- * \param[in] opcode Opcode for the command.
- * \param[in] write_data Pointer to a memory zone where the write_len
- * number of bytes are located to write for this
- * command.
- * \param[in] write_len Number of bytes to write for the command.
- * Between 1 and 8 bytes (both included) can be
- * written.
- * \param[in] addr Address used for the command
- * \param[in] addr_bytes_number Number of address bytes for this command.
- * If an address is not needed for the command,
- * use 0 for argument, otherwise between 1 and
- * 4 bytes (both included) can be used.
- * \param[in] dummy_cycles Number of dummy cycles required for the
- * command, between 0 and 31 (both included).
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- *
- * \note This function will execute two commands: one to program the bytes up to
- * the page boundary and another one to program the rest. It will wait
- * that bytes are programmed from first command before triggering the
- * second one.
- * \note This function does not send a write enable command before the first
- * command and does not check that bytes were programmed after the second
- * command.
- */
-static enum mt25ql_error_t send_boundary_cross_write_cmd(
- struct mt25ql_dev_t* dev,
- uint8_t opcode,
- const void *write_data,
- uint32_t write_len,
- uint32_t addr,
- uint32_t addr_bytes_number,
- uint32_t dummy_cycles)
-{
- enum qspi_ip6514e_error_t controller_error;
- enum mt25ql_error_t library_error;
- /*
- * Remaining bytes between the current address and the end of the current
- * page.
- */
- uint32_t page_remainder = FLASH_PAGE_SIZE - (addr % FLASH_PAGE_SIZE);
-
- /* First write up to the end of the current page. */
- controller_error = qspi_ip6514e_send_write_cmd(dev->controller, opcode,
- write_data, page_remainder,
- addr, addr_bytes_number,
- dummy_cycles);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- write_data = (void *)((uint32_t)write_data + page_remainder);
- addr += page_remainder;
-
- /* Wait for the page to be written before sending new commands. */
- library_error = wait_program_or_erase_complete(dev);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
-
- /* Then write the remaining data of the write_len bytes. */
- send_write_enable(dev);
- controller_error = qspi_ip6514e_send_write_cmd(dev->controller, opcode,
- write_data,
- write_len - page_remainder,
- addr, addr_bytes_number,
- dummy_cycles);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- return MT25QL_ERR_NONE;
-}
-
-enum mt25ql_error_t mt25ql_config_mode(struct mt25ql_dev_t* dev,
- enum mt25ql_functional_state_t f_state)
-{
- enum qspi_ip6514e_error_t controller_error;
- enum mt25ql_error_t library_error;
-
- switch(f_state) {
- case MT25QL_FUNC_STATE_DEFAULT:
- dev->config_state.spi_mode = QSPI_IP6514E_SPI_MODE;
- dev->config_state.opcode_read = READ_CMD;
- dev->config_state.dummy_cycles_read = DEFAULT_READ_DUMMY_CYCLES;
- dev->config_state.opcode_write = PAGE_PROGRAM_CMD;
- dev->config_state.dummy_cycles_write = PAGE_PROGRAM_DUMMY_CYCLES;
- break;
- case MT25QL_FUNC_STATE_FAST:
- dev->config_state.spi_mode = QSPI_IP6514E_SPI_MODE;
- dev->config_state.opcode_read = FAST_READ_CMD;
- dev->config_state.dummy_cycles_read = FAST_READ_DUMMY_CYCLES;
- dev->config_state.opcode_write = PAGE_PROGRAM_CMD;
- dev->config_state.dummy_cycles_write = PAGE_PROGRAM_DUMMY_CYCLES;
- break;
- case MT25QL_FUNC_STATE_QUAD_FAST:
- dev->config_state.spi_mode = QSPI_IP6514E_QSPI_MODE;
- dev->config_state.opcode_read = QUAD_OUTPUT_FAST_READ_CMD;
- dev->config_state.dummy_cycles_read =
- QUAD_OUTPUT_FAST_READ_DUMMY_CYCLES;
- dev->config_state.opcode_write = QUAD_INPUT_FAST_PROGRAM_CMD;
- dev->config_state.dummy_cycles_write =
- QUAD_INPUT_FAST_PROGRAM_DUMMY_CYCLES;
- break;
- default:
- return MT25QL_ERR_WRONG_ARGUMENT;
- }
-
- dev->config_state.func_state = f_state;
-
- /* This function will first set the Flash memory SPI mode and then set
- * the controller's SPI mode. It will fail if the two sides do not have
- * the same mode when this function is called.
- */
- library_error = set_spi_mode(dev, dev->config_state.spi_mode);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
-
- /* Set the number of dummy cycles for read commands. */
- library_error = change_dummy_cycles(
- dev, dev->config_state.dummy_cycles_read);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
-
- /* The rest of the configuration needs the controller to be disabled */
- while(!qspi_ip6514e_is_idle(dev->controller));
- qspi_ip6514e_disable(dev->controller);
-
- /* Set the baud rate divisor as configured in the device structure. */
- controller_error = qspi_ip6514e_set_baud_rate_div(dev->controller,
- dev->baud_rate_div);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- /* Set opcode and dummy cycles needed for read commands. */
- controller_error = qspi_ip6514e_cfg_reads(
- dev->controller, dev->config_state.opcode_read,
- dev->config_state.dummy_cycles_read);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- /* Set opcode and dummy cycles needed for write commands. */
- controller_error = qspi_ip6514e_cfg_writes(
- dev->controller, dev->config_state.opcode_write,
- dev->config_state.dummy_cycles_write);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- /* Set Flash memory constants: bytes per page and address bytes. */
- controller_error = qspi_ip6514e_cfg_page_size(dev->controller,
- FLASH_PAGE_SIZE);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- controller_error = qspi_ip6514e_cfg_addr_bytes(dev->controller,
- ADDR_BYTES);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- qspi_ip6514e_enable(dev->controller);
-
- return MT25QL_ERR_NONE;
-}
-
-enum mt25ql_error_t mt25ql_restore_reset_state(struct mt25ql_dev_t* dev)
-{
- enum mt25ql_error_t library_error;
-
- /*
- * This function will first change the Flash memory mode to single SPI and
- * then change the controller to single SPI. It will fail if the two sides
- * do not have the same mode when this function is called.
- */
- library_error = set_spi_mode(dev, QSPI_IP6514E_SPI_MODE);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
-
- /* Set the default number of dummy cycles for direct read commands. */
- library_error = change_dummy_cycles(dev, RESET_STATE_DUMMY_CYCLES);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
-
- /* The rest of the configuration needs the controller to be disabled */
- while(!qspi_ip6514e_is_idle(dev->controller));
- qspi_ip6514e_disable(dev->controller);
-
- /* Restore the default value of the QSPI controller registers. */
- qspi_ip6514e_reset_regs(dev->controller);
-
- qspi_ip6514e_enable(dev->controller);
-
- dev->config_state = (struct mt25ql_config_state_t){ MT25QL_FUNC_STATE_NOT_INITED };
- dev->config_state.func_state = MT25QL_FUNC_STATE_NOT_INITED;
-
- return MT25QL_ERR_NONE;
-}
-
-enum mt25ql_error_t mt25ql_direct_read(struct mt25ql_dev_t* dev,
- uint32_t addr,
- void *data,
- uint32_t len)
-{
- /*
- * The direct access window size is the size of the memory that can be
- * accessed with a direct access.
- */
- uint32_t direct_access_window_size = dev->controller->cfg->addr_mask + 1;
- /*
- * The window number is the number of times it will be needed to remap the
- * address with the remap register. We move this Direct Access window first
- * window_number times starting at the beginning address to read full
- * windows of direct_access_window_size bytes. Then we read the remainder
- * bytes.
- */
- uint32_t window_number = len / direct_access_window_size;
-
- if (data == NULL || len == 0) {
- return MT25QL_ERR_WRONG_ARGUMENT;
- }
-
- if ((addr + len) >= dev->size) {
- return MT25QL_ERR_ADDR_TOO_BIG;
- }
-
- /*
- * There is no limitation reading through a Flash page boundary hence we
- * do not add the same logic here than in the write function.
- */
-
- /* Transfer the bytes for the window_number windows first. */
- for (uint32_t window = 0; window < window_number; window++) {
- qspi_ip6514e_remap_addr(dev->controller, addr);
-
- /*
- * The AHB address to access the Flash memory does not change but it
- * will be translated differently thanks to the remap function.
- */
- memcpy(data,
- (void *)dev->direct_access_start_addr,
- direct_access_window_size);
-
- len -= direct_access_window_size;
- data = (void *)((uint32_t)data + direct_access_window_size);
- addr += direct_access_window_size;
- }
-
- if (len) {
- /* Transfer the reminder bytes */
- qspi_ip6514e_remap_addr(dev->controller, addr);
-
- memcpy(data, (void *)dev->direct_access_start_addr, len);
- }
-
- /* Disable remapping for direct accesses outside of this function. */
- qspi_ip6514e_disable_remap(dev->controller);
-
- return MT25QL_ERR_NONE;
-}
-
-enum mt25ql_error_t mt25ql_direct_write(struct mt25ql_dev_t* dev,
- uint32_t addr,
- const void *data,
- uint32_t len)
-{
- enum mt25ql_error_t library_error;
- /*
- * The direct access window size is the size of the memory that can be
- * accessed with a direct access.
- */
- uint32_t direct_access_window_size = dev->controller->cfg->addr_mask + 1;
- uint32_t window_number;
- /* Offset between address and the previous 32 bits aligned word */
- uint32_t word_offset;
-
- if (data == NULL || len == 0) {
- return MT25QL_ERR_WRONG_ARGUMENT;
- }
-
- if ((addr + len) >= dev->size) {
- return MT25QL_ERR_ADDR_TOO_BIG;
- }
-
- /*
- * If the remapping address is not aligned on a 32 bits boundary, a direct
- * access of one word could cross a Flash page boundary. If that happens,
- * the bytes of that word that are over the page boundary will instead be
- * written at the beginning of the same page.
- * To counter this problem, we align the remapping address and add the word
- * offset to the address of the direct access for the first window only.
- */
- word_offset = addr % BYTES_PER_WORD;
- /* Make address aligned on a 32 bits alignment. */
- addr -= word_offset;
- /*
- * Only direct_access_window_size address locations are available by direct
- * access. We calculate the number of windows that we will need to transfer
- * len bytes. We have to add in the window the offset that we add in the
- * beginning.
- */
- window_number = (len + word_offset) / direct_access_window_size;
-
- /*
- * This function assumes that the flash has already been erased.
- * Transfer the bytes for the window_number windows first.
- */
- for (uint32_t window = 0; window < window_number; window++) {
- /* The controller needs to be disabled while remapping is done. */
- qspi_ip6514e_remap_addr(dev->controller, addr);
-
- /*
- * The AHB address to access the Flash memory does not change but it
- * will be translated differently thanks to the remap function.
- */
- memcpy((void *)(dev->direct_access_start_addr + word_offset),
- data,
- direct_access_window_size - word_offset);
-
- len -= (direct_access_window_size - word_offset);
- data = (void *)((uint32_t)data +
- (direct_access_window_size - word_offset));
- addr += direct_access_window_size;
-
- /*
- * The address is now aligned, there is no need to add an offset for the
- * remaining windows.
- */
- word_offset = 0;
-
- /*
- * Wait until the last program operation is complete before changing
- * the remap address.
- */
- library_error = wait_program_or_erase_complete(dev);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
- }
-
- if (len) {
- /* Transfer the reminder bytes */
- qspi_ip6514e_remap_addr(dev->controller, addr);
-
- memcpy((void *)(dev->direct_access_start_addr + word_offset),
- data,
- len);
-
- /* Wait until the last program operation is complete */
- library_error = wait_program_or_erase_complete(dev);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
- }
-
- /*
- * Disable the default remap address for direct accesses outside of this
- * function.
- */
- qspi_ip6514e_disable_remap(dev->controller);
-
- return MT25QL_ERR_NONE;
-}
-
-enum mt25ql_error_t mt25ql_command_read(struct mt25ql_dev_t* dev,
- uint32_t addr,
- void *data,
- uint32_t len)
-{
- /* With one single command only 8 bytes can be read. */
- uint32_t cmd_number = len / CMD_DATA_MAX_SIZE;
- enum qspi_ip6514e_error_t controller_error;
-
- if (dev->config_state.func_state == MT25QL_FUNC_STATE_NOT_INITED) {
- return MT25QL_ERR_NOT_INITED;
- }
-
- for (uint32_t cmd_index = 0; cmd_index < cmd_number; cmd_index++) {
- controller_error = qspi_ip6514e_send_read_cmd(
- dev->controller,
- dev->config_state.opcode_read,
- data, CMD_DATA_MAX_SIZE, addr,
- ADDR_BYTES,
- dev->config_state.dummy_cycles_read);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- data = (void *)((uint32_t)data + CMD_DATA_MAX_SIZE);
- addr += CMD_DATA_MAX_SIZE;
- len -= CMD_DATA_MAX_SIZE;
- }
-
- if (len) {
- /* Read the remainder. */
- controller_error = qspi_ip6514e_send_read_cmd(
- dev->controller,
- dev->config_state.opcode_read,
- data, len, addr, ADDR_BYTES,
- dev->config_state.dummy_cycles_read);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
- }
-
- return MT25QL_ERR_NONE;
-
-}
-
-enum mt25ql_error_t mt25ql_command_write(struct mt25ql_dev_t* dev,
- uint32_t addr,
- const void *data,
- uint32_t len)
-{
- /* With one single command only 8 bytes can be written. */
- uint32_t cmd_number = len / CMD_DATA_MAX_SIZE;
- enum qspi_ip6514e_error_t controller_error;
- enum mt25ql_error_t library_error;
-
- if (dev->config_state.func_state == MT25QL_FUNC_STATE_NOT_INITED) {
- return MT25QL_ERR_NOT_INITED;
- }
-
- for (uint32_t cmd_index = 0; cmd_index < cmd_number; cmd_index++) {
- send_write_enable(dev);
-
- /*
- * Check if this command is not writing over a page boundary: first and
- * last bytes are in the same page.
- */
- if ((addr / FLASH_PAGE_SIZE) !=
- ((addr + CMD_DATA_MAX_SIZE - 1) / FLASH_PAGE_SIZE)) {
- /* The CMD_DATA_MAX_SIZE bytes written are crossing the boundary. */
- library_error = send_boundary_cross_write_cmd(
- dev, dev->config_state.opcode_write,
- data, CMD_DATA_MAX_SIZE, addr,
- ADDR_BYTES,
- dev->config_state.dummy_cycles_write);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
- } else {
- /* Normal case: not crossing the boundary. */
- controller_error = qspi_ip6514e_send_write_cmd(
- dev->controller,
- dev->config_state.opcode_write,
- data, CMD_DATA_MAX_SIZE, addr,
- ADDR_BYTES,
- dev->config_state.dummy_cycles_write);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
- }
-
- /* Wait until the write operation is complete. */
- library_error = wait_program_or_erase_complete(dev);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
-
- data = (void *)((uint32_t)data + CMD_DATA_MAX_SIZE);
- addr += CMD_DATA_MAX_SIZE;
- len -= CMD_DATA_MAX_SIZE;
- }
-
- if (len) {
- /* Write the remainder. */
- send_write_enable(dev);
- /*
- * Check if this command is not writing over a page boundary: first and
- * last bytes are in the same page.
- */
- if ((addr / FLASH_PAGE_SIZE) != ((addr + len - 1) / FLASH_PAGE_SIZE)) {
- /* The CMD_DATA_MAX_SIZE bytes written are crossing the boundary. */
- library_error = send_boundary_cross_write_cmd(
- dev, dev->config_state.opcode_write,
- data, len, addr, ADDR_BYTES,
- dev->config_state.dummy_cycles_write);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
- } else {
- /* Normal case: not crossing the boundary. */
- controller_error = qspi_ip6514e_send_write_cmd(
- dev->controller,
- dev->config_state.opcode_write,
- data, len, addr, ADDR_BYTES,
- dev->config_state.dummy_cycles_write);
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
- }
-
- /* Wait until the write operation is complete. */
- library_error = wait_program_or_erase_complete(dev);
- if (library_error != MT25QL_ERR_NONE) {
- return library_error;
- }
- }
-
- return MT25QL_ERR_NONE;
-
-}
-
-enum mt25ql_error_t mt25ql_erase(struct mt25ql_dev_t* dev,
- uint32_t addr,
- enum mt25ql_erase_t erase_type)
-{
- enum qspi_ip6514e_error_t controller_error;
- enum mt25ql_error_t library_error;
- uint8_t erase_cmd;
- uint32_t addr_bytes;
-
- if (dev->config_state.func_state == MT25QL_FUNC_STATE_NOT_INITED) {
- return MT25QL_ERR_NOT_INITED;
- }
-
- send_write_enable(dev);
-
- switch (erase_type) {
- case MT25QL_ERASE_ALL_FLASH:
- if (addr != 0) {
- return MT25QL_ERR_ADDR_NOT_ALIGNED;
- }
- erase_cmd = BULK_ERASE_CMD;
- addr_bytes = ARG_NOT_USED;
- break;
- case MT25QL_ERASE_SECTOR_64K:
- erase_cmd = SECTOR_ERASE_CMD;
- addr_bytes = ADDR_BYTES;
- if ((addr % SECTOR_64KB) != 0) {
- return MT25QL_ERR_ADDR_NOT_ALIGNED;
- }
- break;
- case MT25QL_ERASE_SUBSECTOR_32K:
- erase_cmd = SUBSECTOR_ERASE_32KB_CMD;
- addr_bytes = ADDR_BYTES;
- if ((addr % SUBSECTOR_32KB) != 0) {
- return MT25QL_ERR_ADDR_NOT_ALIGNED;
- }
- break;
- case MT25QL_ERASE_SUBSECTOR_4K:
- erase_cmd = SUBSECTOR_ERASE_4KB_CMD;
- addr_bytes = ADDR_BYTES;
- if ((addr % SUBSECTOR_4KB) != 0) {
- return MT25QL_ERR_ADDR_NOT_ALIGNED;
- }
- break;
- default:
- return MT25QL_ERR_WRONG_ARGUMENT;
- }
-
- if (addr >= dev->size) {
- return MT25QL_ERR_ADDR_TOO_BIG;
- }
-
- controller_error = qspi_ip6514e_send_cmd(dev->controller,
- erase_cmd,
- ARG_PTR_NOT_USED,
- ARG_NOT_USED,
- ARG_PTR_NOT_USED,
- ARG_NOT_USED,
- addr,
- addr_bytes,
- 0); /* No dummy cycles needed for
- any erase command. */
- if (controller_error != QSPI_IP6514E_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- /* Wait until the erase operation is complete */
- library_error = wait_program_or_erase_complete(dev);
- if (library_error != MT25QL_ERR_NONE) {
- return (enum mt25ql_error_t)controller_error;
- }
-
- return MT25QL_ERR_NONE;
-}
diff --git a/platform/ext/target/musca_a/Libraries/mt25ql_flash_lib.h b/platform/ext/target/musca_a/Libraries/mt25ql_flash_lib.h
deleted file mode 100644
index c2dac2c..0000000
--- a/platform/ext/target/musca_a/Libraries/mt25ql_flash_lib.h
+++ /dev/null
@@ -1,271 +0,0 @@
-/*
- * Copyright (c) 2018-2019 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/*
- * This library provides functions to control the MT25QL256ABA-1EW7-OSIT flash
- * memory from Micron and should work for similar devices from the same vendor.
- */
-
-#ifndef __MT25QL_H__
-#define __MT25QL_H__
-
-#include "qspi_ip6514e_drv.h"
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/**
- * \brief MT25QL Flash Memory documentation defined values.
- */
-#define FLASH_PAGE_SIZE (256U) /* 256B */
-#define SUBSECTOR_4KB (0x00001000U) /* 4KB */
-#define SUBSECTOR_32KB (0x00008000U) /* 32KB */
-#define SECTOR_64KB (0x00010000U) /* 64KB */
-#define ADDR_BYTES (3U)
-
-enum mt25ql_error_t {
- MT25QL_ERR_NONE = QSPI_IP6514E_ERR_NONE,
- MT25QL_ERR_WRONG_ARGUMENT = QSPI_IP6514E_ERR_WRONG_ARGUMENT,
- MT25QL_ERR_CTRL_NOT_DISABLED = QSPI_IP6514E_ERR_CONTROLLER_NOT_DISABLED,
- MT25QL_ERR_READ_IN_PROGRESS = QSPI_IP6514E_ERR_READ_IN_PROGRESS,
- MT25QL_ERR_WRITE_IN_PROGRESS = QSPI_IP6514E_ERR_WRITE_IN_PROGRESS,
- MT25QL_ERR_ADDR_NOT_ALIGNED,
- MT25QL_ERR_NOT_INITED,
- MT25QL_ERR_ADDR_TOO_BIG,
-};
-
-enum mt25ql_erase_t {
- MT25QL_ERASE_ALL_FLASH = 0U, /*!< Erase all flash */
- MT25QL_ERASE_SUBSECTOR_4K = SUBSECTOR_4KB, /*!< Erase a 4 KB subsector */
- MT25QL_ERASE_SUBSECTOR_32K = SUBSECTOR_32KB, /*!< Erase a 32 KB subsector */
- MT25QL_ERASE_SECTOR_64K = SECTOR_64KB, /*!< Erase a sector (64 KB) */
-};
-
-enum mt25ql_functional_state_t {
- MT25QL_FUNC_STATE_NOT_INITED = 0U,
- /*!< QSPI Flash controller is not initialized, only direct read
- * is guaranteed to be working
- */
- MT25QL_FUNC_STATE_DEFAULT = 1U,
- /*!< The QSPI Flash controller and memory is in default state,
- * using basic read/write commands
- */
- MT25QL_FUNC_STATE_FAST = 2U,
- /*!< The QSPI Flash controller and memory is configured to operate in
- * single SPI mode and fast Flash commands could be used for read and
- * program operations.
- */
- MT25QL_FUNC_STATE_QUAD_FAST = 3U,
- /*!< The QSPI Flash controller and memory is configured to operate in
- * Quad SPI mode and fast Flash commands could be used for read and
- * program operations.
- */
-};
-
-struct mt25ql_config_state_t {
- enum mt25ql_functional_state_t func_state;
- /*!< Functional state id */
- enum qspi_ip6514e_spi_mode_t spi_mode;
- /*!< SPI mode for the current functional state */
- uint8_t opcode_read;
- /*!< Read opcode for the current functional state */
- uint8_t opcode_write;
- /*!< Write opcode for the current functional state */
- uint32_t dummy_cycles_read;
- /*!< Dummy cycles for the read command for the current functional state */
- uint32_t dummy_cycles_write;
- /*!< Dummy cycles for the write command for the current functional state */
-};
-
-struct mt25ql_dev_t {
- struct qspi_ip6514e_dev_t *controller;
- /*!< QSPI Flash controller. */
- uint32_t direct_access_start_addr;
- /*!< AHB address to directly access the contents of the Flash memory
- * through the QSPI Controller.
- */
- uint32_t baud_rate_div;
- /*!< Clock divisor that will be used to configure the QSPI Flash
- * Controller to access the Flash memory. The clock which frequency is
- * divived is the one linked to the QSPI Flash controller. It can only
- * be an even number between 2 and 32 (both included). It needs to be
- * high enough to support the Quad Output Fast Read command with 8
- * dummy cycles and the Quad Input Fast Program with 0 dummy cycles.
- */
- uint32_t size; /*!< Total size of the MT25QL Flash memory */
- struct mt25ql_config_state_t config_state;
- /*!< Configured functional state (with parameter settings) of the
- * QSPI Flash controller and memory.
- */
-
-};
-
-/**
- * \brief Change configuration of the QSPI Flash controller and MT25QL memory
- *
- * Changes the configuration of the QSPI Flash controller and MT25QL
- * Flash memory to operate in the specified SPI mode and to use the
- * appropriate Flash commands for read and program operations.
- * It also sets:
- * + The number of dummy cycles for each operation
- * + The bytes per page constant to 256 (MT25QL Flash specific)
- * + The number of address bytes to 3
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- * \param[in] f_state Functional state to be set on flash controller
- * and device \ref mt25ql_functional_state_t
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- *
- * \note This function assumes that the Flash memory device and the QSPI Flash
- * controller operates with the same SPI protocol. This function will fail
- * if the Flash device is in a different configuration.
- */
-enum mt25ql_error_t mt25ql_config_mode(struct mt25ql_dev_t* dev,
- enum mt25ql_functional_state_t f_state);
-
-/**
- * \brief Restore the QSPI Flash controller and MT25QL to reset state.
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- *
- * \note This function assumes that the Flash memory device and the QSPI Flash
- * controller operates with the same SPI protocol. This function will fail
- * if the Flash device is in a different configuration.
- */
-enum mt25ql_error_t mt25ql_restore_reset_state(struct mt25ql_dev_t* dev);
-
-/**
- * \brief Read bytes from the flash memory (direct access)
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- * \param[in] addr Flash memory address for the read operation
- * \param[out] data Pointer where len bytes read from the flash memory will be
- * written to
- * \param[in] len Number of bytes to read
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- *
- * \note This function will use direct access to read from the Flash memory. It
- * can be used to access above the direct accessible memory zone if
- * not all the AHB address wires are connected.
- * \note The address given should be the address of the data inside the flash
- * memory. To read the first byte inside the memory, use 0x00000000.
- */
-enum mt25ql_error_t mt25ql_direct_read(struct mt25ql_dev_t* dev,
- uint32_t addr,
- void *data,
- uint32_t len);
-
-/**
- * \brief Write bytes in the flash memory, at a location where data has already
- * been erased (direct access)
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- * \param[in] addr Flash memory address for the write operation
- * \param[in] data Pointer to the len bytes that will be written to the flash
- * memory
- * \param[in] len Number of bytes to write
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- *
- * \note This function will use direct access to write to the Flash memory. It
- * can be used to access outside of the direct accessible memory zone if
- * not all the AHB address wires are connected.
- * \note The address given should be the address of the data inside the flash
- * memory. To write the first byte inside the memory, use 0x00000000.
- * \note Writing bytes in the flash memory clear them from 1 to 0, for that
- * matter the location where data is written needs to be erased
- * beforehand.
- */
-enum mt25ql_error_t mt25ql_direct_write(struct mt25ql_dev_t* dev,
- uint32_t addr,
- const void *data,
- uint32_t len);
-
-/**
- * \brief Read bytes from the flash memory (using Flash commands)
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- * \param[in] addr Flash memory address for the read operation
- * \param[out] data Pointer where len bytes read from the flash memory will be
- * written to
- * \param[in] len Number of bytes to read
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- *
- * \note This function will use the Software Triggered Instruction Generator to
- * read from the Flash memory using Flash commands.
- * \note The address given should be the address of the data inside the flash
- * memory. To read the first byte inside the memory, use 0x00000000.
- */
-enum mt25ql_error_t mt25ql_command_read(struct mt25ql_dev_t* dev,
- uint32_t addr,
- void *data,
- uint32_t len);
-
-/**
- * \brief Write bytes in the flash memory, at a location where data has already
- * been erased (using Flash commands)
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- * \param[in] addr Flash memory address for the write operation
- * \param[in] data Pointer to the len bytes that will be written to the flash
- * memory
- * \param[in] len Number of bytes to write
- *
- * \return Return error code as specified in \ref mt25ql_error_t
- *
- * \note This function will use the Software Triggered Instruction Generator to
- * write to the Flash memory using Flash commands.
- * \note The address given should be the address of the data inside the flash
- * memory. To write the first byte inside the memory, use 0x00000000.
- * \note Writing bytes in the flash memory clear them from 1 to 0, for that
- * matter the location where data is written needs to be erased
- * beforehand.
- */
-enum mt25ql_error_t mt25ql_command_write(struct mt25ql_dev_t* dev,
- uint32_t addr,
- const void *data,
- uint32_t len);
-
-/**
- * \brief Erase all flash memory, a sector (64 KiB) or a subsector
- * (32 KiB or 4 KiB)
- *
- * \param[in] dev Pointer to MT25QL device structure \ref mt25ql_dev_t
- * \param[in] addr Address where to erase in the flash memory
- * \param[in] erase_type Type of what to erase at the specified address:
- * * whole flash memory
- * * a subsector (4 KiB or 32 KiB)
- * * a sector (64 KiB)
- * \return Return error code as specified in \ref mt25ql_error_t
- *
- * \note The address need to be aligned with the size of what is erased or 0 if
- * all flash memory is to be erased.
- */
-enum mt25ql_error_t mt25ql_erase(struct mt25ql_dev_t* dev,
- uint32_t addr,
- enum mt25ql_erase_t erase_type);
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __MT25QL_H__ */
diff --git a/platform/ext/target/musca_a/Native_Driver/gpio_cmsdk_drv.c b/platform/ext/target/musca_a/Native_Driver/gpio_cmsdk_drv.c
deleted file mode 100644
index 7026069..0000000
--- a/platform/ext/target/musca_a/Native_Driver/gpio_cmsdk_drv.c
+++ /dev/null
@@ -1,324 +0,0 @@
-/*
- * Copyright (c) 2016-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include <stdint.h>
-#include <stddef.h>
-#include "gpio_cmsdk_drv.h"
-
-/* GPIO register map structure */
-struct gpio_cmsdk_reg_map_t {
- volatile uint32_t data; /* Offset: 0x000 (R/W) Data register */
- volatile uint32_t dataout; /* Offset: 0x004 (R/W) Data output
- * latch register */
- volatile uint32_t reserved0[2];
- volatile uint32_t outenableset; /* Offset: 0x010 (R/W) Output enable
- * set register */
- volatile uint32_t outenableclr; /* Offset: 0x014 (R/W) Output enable
- * clear register */
- volatile uint32_t altfuncset; /* Offset: 0x018 (R/W) Alternate function
- * set register */
- volatile uint32_t altfuncclr; /* Offset: 0x01C (R/W) Alternate function
- * clear register */
- volatile uint32_t intenset; /* Offset: 0x020 (R/W) Interrupt enable
- * set register */
- volatile uint32_t intenclr; /* Offset: 0x024 (R/W) Interrupt enable
- * clear register */
- volatile uint32_t inttypeset; /* Offset: 0x028 (R/W) Interrupt type
- * set register */
- volatile uint32_t inttypeclr; /* Offset: 0x02C (R/W) Interrupt type
- * clear register */
- volatile uint32_t intpolset; /* Offset: 0x030 (R/W) Interrupt polarity
- * set register */
- volatile uint32_t intpolclr; /* Offset: 0x034 (R/W) Interrupt polarity
- * clear register */
- union {
- volatile uint32_t intstatus; /* Offset: 0x038 (R/ ) Interrupt status
- * register */
- volatile uint32_t intclear; /* Offset: 0x038 ( /W) Interrupt clear
- * register */
- }intreg;
- volatile uint32_t reserved1[997];
- volatile uint32_t pid4; /* Peripheral ID Register 4 */
- volatile uint32_t pid0; /* Peripheral ID Register 0 */
- volatile uint32_t pid1; /* Peripheral ID Register 1 */
- volatile uint32_t pid2; /* Peripheral ID Register 2 */
- volatile uint32_t pid3; /* Peripheral ID Register 3 */
- volatile uint32_t cid0; /* Component ID Register 0 */
- volatile uint32_t cid1; /* Component ID Register 1 */
- volatile uint32_t cid2; /* Component ID Register 2 */
- volatile uint32_t cid4; /* Component ID Register 3 */
-};
-
-void gpio_cmsdk_init(struct gpio_cmsdk_dev_t* dev)
-{
- /* Nothing to init on the GPIO device */
-}
-
-/**
- * \brief Configures port.
- *
- * \param[in] dev GPIO device to initalize \ref gpio_cmsdk_dev_t
- * \param[in] pin_mask Pin mask for port access
- * \param[in] direction Input or output \ref gpio_cmsdk_direction_t
- * \param[in] altfunc_flags Alternate function \ref gpio_cmsdk_altfunc_t
- *
- */
-static void set_port_config(struct gpio_cmsdk_dev_t* dev, uint32_t pin_mask,
- enum gpio_cmsdk_direction_t direction,
- enum gpio_cmsdk_altfunc_t altfunc_flags)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- if(direction == GPIO_CMSDK_INPUT) {
- p_gpio_port->outenableclr = pin_mask;
- } else {
- p_gpio_port->outenableset = pin_mask;
- }
-
- if (altfunc_flags == GPIO_CMSDK_MAIN_FUNC) {
- p_gpio_port->altfuncclr = pin_mask;
- } else {
- p_gpio_port->altfuncset = pin_mask;
- }
-
- return;
-}
-
-enum gpio_cmsdk_error_t
-gpio_cmsdk_pin_config(struct gpio_cmsdk_dev_t* dev, uint32_t pin_num,
- enum gpio_cmsdk_direction_t direction,
- enum gpio_cmsdk_altfunc_t altfunc_flags)
-{
- uint32_t pin_mask = (1UL << pin_num);
-
- if(pin_num >= GPIO_CMSDK_MAX_PIN_NUM) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- set_port_config(dev, pin_mask, direction, altfunc_flags);
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-enum gpio_cmsdk_error_t
-gpio_cmsdk_port_config(struct gpio_cmsdk_dev_t* dev, uint32_t pin_mask,
- enum gpio_cmsdk_direction_t direction,
- enum gpio_cmsdk_altfunc_t altfunc_flags)
-{
- if(pin_mask > GPIO_CMSDK_MAX_PORT_MASK) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- set_port_config(dev, pin_mask, direction, altfunc_flags);
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-void gpio_cmsdk_config_irq(struct gpio_cmsdk_dev_t* dev, uint32_t pin_mask,
- enum gpio_cmsdk_irq_type_t irq_type,
- enum gpio_cmsdk_irq_polarity_t irq_pol)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- /* Interrupt type: EDGE = 1 - LEVEL = 0 */
- if(irq_type == GPIO_CMSDK_IRQ_EDGE) {
- p_gpio_port->inttypeset = pin_mask;
- } else if(irq_type == GPIO_CMSDK_IRQ_LEVEL) {
- p_gpio_port->inttypeclr = pin_mask;
- }
-
- /* Interrupt polarity */
- if(irq_pol == GPIO_CMSDK_IRQ_LOW_OR_FALLING_EDGE) {
- p_gpio_port->intpolclr = pin_mask;
- } else if(irq_pol == GPIO_CMSDK_IRQ_HIGH_OR_RISING_EDGE) {
- p_gpio_port->intpolset = pin_mask;
- }
-}
-
-enum gpio_cmsdk_error_t gpio_cmsdk_pin_write(struct gpio_cmsdk_dev_t* dev,
- uint32_t pin_num,
- uint32_t value)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- /* GPIO data output register is a read-modify-write register,
- * so before writing a value on a GPIO pin it is required to disable
- * the interrupts to prevent concurrency problems.
- */
- if(pin_num >= GPIO_CMSDK_MAX_PIN_NUM) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
- if(value) {
- /* Sets the pin */
- p_gpio_port->dataout |= (1UL << pin_num);
- } else {
- /* Clears the pin */
- p_gpio_port->dataout &= ~(1UL << pin_num);
- }
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-enum gpio_cmsdk_error_t gpio_cmsdk_port_write(struct gpio_cmsdk_dev_t* dev,
- uint32_t pin_mask,
- uint32_t value)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- /* GPIO data output register is a read-modify-write register,
- * so before writing a value on a GPIO pin it is required to disable
- * the interrupts to prevent concurrency problems.
- */
- if(pin_mask > GPIO_CMSDK_MAX_PORT_MASK) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- /* Clear all bits defined in the mask,
- * and set selected bits from value parameter.
- */
- p_gpio_port->dataout =
- ((~pin_mask & p_gpio_port->dataout) | (pin_mask & value));
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-enum gpio_cmsdk_error_t
-gpio_cmsdk_pin_read(struct gpio_cmsdk_dev_t* dev,
- uint32_t pin_num,
- uint32_t *data)
-{
- uint32_t value;
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- if(pin_num >= GPIO_CMSDK_MAX_PIN_NUM) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- value = p_gpio_port->data;
-
- *data = (value >> pin_num) & 1UL;
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-enum gpio_cmsdk_error_t
-gpio_cmsdk_port_read(struct gpio_cmsdk_dev_t* dev, uint32_t pin_mask,
- uint32_t *data)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- if(pin_mask > GPIO_CMSDK_MAX_PORT_MASK) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- *data = p_gpio_port->data & pin_mask;
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-enum gpio_cmsdk_error_t
-gpio_cmsdk_set_pin_irq_cfg(struct gpio_cmsdk_dev_t* dev, uint32_t pin_num,
- enum gpio_cmsdk_irq_status_t status)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- if(pin_num >= GPIO_CMSDK_MAX_PIN_NUM) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- if(status == GPIO_CMSDK_IRQ_ENABLE) {
- p_gpio_port->intenset = (1UL << pin_num);
- } else {
- p_gpio_port->intenclr = (1UL << pin_num);
- }
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-enum gpio_cmsdk_error_t
-gpio_cmsdk_set_port_irq_cfg(struct gpio_cmsdk_dev_t* dev, uint32_t pin_mask,
- enum gpio_cmsdk_irq_status_t status)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- if(pin_mask > GPIO_CMSDK_MAX_PORT_MASK) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- if(status == GPIO_CMSDK_IRQ_ENABLE) {
- p_gpio_port->intenset = pin_mask;
- } else {
- p_gpio_port->intenclr = pin_mask;
- }
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-enum gpio_cmsdk_error_t
-gpio_cmsdk_get_pin_irq_status(struct gpio_cmsdk_dev_t* dev,
- uint32_t pin_num, uint32_t* status)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- if(pin_num >= GPIO_CMSDK_MAX_PIN_NUM) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- *status = ((p_gpio_port->intreg.intstatus >> pin_num) & 1UL);
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-enum gpio_cmsdk_error_t
-gpio_cmsdk_get_port_irq_status(struct gpio_cmsdk_dev_t* dev,
- uint32_t pin_mask, uint32_t* status)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- if(pin_mask > GPIO_CMSDK_MAX_PORT_MASK) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- *status = (p_gpio_port->intreg.intstatus & pin_mask);
-
- return GPIO_CMSDK_ERR_NONE;
-}
-
-
-enum gpio_cmsdk_error_t gpio_cmsdk_clear_irq(struct gpio_cmsdk_dev_t* dev,
- uint8_t pin_num)
-{
- struct gpio_cmsdk_reg_map_t* p_gpio_port =
- (struct gpio_cmsdk_reg_map_t*)dev->cfg->base;
-
- if(pin_num >= GPIO_CMSDK_MAX_PIN_NUM) {
- return GPIO_CMSDK_ERR_INVALID_ARG;
- }
-
- p_gpio_port->intreg.intclear = (1UL << pin_num);
-
- return GPIO_CMSDK_ERR_NONE;
-}
diff --git a/platform/ext/target/musca_a/Native_Driver/gpio_cmsdk_drv.h b/platform/ext/target/musca_a/Native_Driver/gpio_cmsdk_drv.h
deleted file mode 100644
index 2671cc4..0000000
--- a/platform/ext/target/musca_a/Native_Driver/gpio_cmsdk_drv.h
+++ /dev/null
@@ -1,279 +0,0 @@
-/*
- * Copyright (c) 2016-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file gpio_cmsdk_drv.h
- * \brief Generic driver for ARM GPIO.
- */
-
-#ifndef __GPIO_CMSDK_DRV_H__
-#define __GPIO_CMSDK_DRV_H__
-
-#include <stdint.h>
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-#define GPIO_CMSDK_MAX_PIN_NUM 16U
-#define GPIO_CMSDK_MAX_PORT_MASK ((1U << GPIO_CMSDK_MAX_PIN_NUM) - 1U)
-
-/* GPIO enumeration types */
-enum gpio_cmsdk_direction_t {
- GPIO_CMSDK_INPUT = 0, /*!< GPIO is input */
- GPIO_CMSDK_OUTPUT /*!< GPIO is output */
-};
-
-enum gpio_cmsdk_altfunc_t {
- GPIO_CMSDK_MAIN_FUNC = 0, /*!< Alternate function is not enabled */
- GPIO_CMSDK_ALT_FUNC /*!< Alternate function is enabled */
-};
-
-enum gpio_cmsdk_irq_status_t {
- GPIO_CMSDK_IRQ_DISABLE = 0, /*!< Disable interruptions */
- GPIO_CMSDK_IRQ_ENABLE /*!< Enable interruptions */
-};
-
-enum gpio_cmsdk_irq_type_t {
- GPIO_CMSDK_IRQ_LEVEL = 0, /*!< Level Interrupt */
- GPIO_CMSDK_IRQ_EDGE /*!< Edge Interrupt */
-};
-
-enum gpio_cmsdk_irq_polarity_t {
- GPIO_CMSDK_IRQ_LOW_OR_FALLING_EDGE = 0, /*!< Interrupt active low or
- falling edge */
- GPIO_CMSDK_IRQ_HIGH_OR_RISING_EDGE /*!< Interrupt active high or
- rising edge */
-};
-
-enum gpio_cmsdk_error_t {
- GPIO_CMSDK_ERR_NONE = 0, /*!< No error */
- GPIO_CMSDK_ERR_INVALID_ARG, /*!< Error invalid input argument */
- GPIO_CMSDK_ALTFUNC_EERROR, /*!< Alternate function returned error */
-};
-
-/* CMSDK GPIO device configuration structure */
-struct gpio_cmsdk_dev_cfg_t {
- const uint32_t base; /*!< GPIO base address */
-};
-
-/* CMSDK GPIO device structure */
-struct gpio_cmsdk_dev_t {
- const struct gpio_cmsdk_dev_cfg_t* const cfg; /*!< GPIO configuration */
-};
-
-/**
- * \brief Initializes GPIO port.
- *
- * \param[in] dev GPIO device to initalize \ref gpio_cmsdk_dev_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void gpio_cmsdk_init(struct gpio_cmsdk_dev_t* dev);
-
-/**
- * \brief Configures pin.
- *
- * \param[in] dev GPIO device to configure \ref gpio_cmsdk_dev_t
- * \param[in] pin_num Pin number for pin access
- * \param[in] direction Input or output \ref gpio_cmsdk_direction_t
- * \param[in] altfunc_flags Alternate function \ref gpio_cmsdk_altfunc_t
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_flags_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum gpio_cmsdk_error_t
-gpio_cmsdk_pin_config(struct gpio_cmsdk_dev_t* dev, uint32_t pin_num,
- enum gpio_cmsdk_direction_t direction,
- enum gpio_cmsdk_altfunc_t altfunc_flags);
-
-/**
- * \brief Configures port.
- *
- * \param[in] dev GPIO device to configure \ref gpio_cmsdk_dev_t
- * \param[in] pin_mask Bitmask of the selected pins
- * \param[in] direction Input or output \ref gpio_cmsdk_direction_t
- * \param[in] altfunc_flags Alternate function \ref gpio_cmsdk_altfunc_t
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum gpio_cmsdk_error_t
-gpio_cmsdk_port_config(struct gpio_cmsdk_dev_t* dev, uint32_t pin_mask,
- enum gpio_cmsdk_direction_t direction,
- enum gpio_cmsdk_altfunc_t altfunc_flags);
-
-
-/**
- * \brief Configures interrupt type
- *
- * \param[in] dev GPIO device to initalize \ref gpio_cmsdk_dev_t
- * \param[in] pin_mask Bitmask of the selected pins
- * \param[in] irq_type Interrupt type \ref gpio_cmsdk_irq_type_t
- * \param[in] irq_pol Interrupt polarity \ref gpio_cmsdk_irq_polarity_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void gpio_cmsdk_config_irq(struct gpio_cmsdk_dev_t* dev, uint32_t pin_mask,
- enum gpio_cmsdk_irq_type_t irq_type,
- enum gpio_cmsdk_irq_polarity_t irq_pol);
-
-/**
- * \brief Sets state of the output pin.
- *
- * \param[in] dev GPIO device to use for the pin \ref gpio_cmsdk_dev_t
- * \param[in] pin_num Pin number for pin access
- * \param[in] value Value(s) to set.
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- * \note GPIO data output register is a read-modify-write register,
- * so before writing a value on a GPIO pin it is required to disable
- * the interrupts to prevent concurrency problems.
- */
-enum gpio_cmsdk_error_t gpio_cmsdk_pin_write(struct gpio_cmsdk_dev_t* dev,
- uint32_t pin_num,
- uint32_t value);
-
-/**
- * \brief Sets state of the output port.
- *
- * \param[in] dev GPIO device to use for the pins \ref gpio_cmsdk_dev_t
- * \param[in] pin_mask Bitmask of the selected pins
- * \param[in] value Bitmask of pins states to set
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- * \note GPIO data output register is a read-modify-write register,
- * so before writing a value on a GPIO pin it is required to disable
- * the interrupts to prevent concurrency problems.
- */
-enum gpio_cmsdk_error_t gpio_cmsdk_port_write(struct gpio_cmsdk_dev_t* dev,
- uint32_t pin_mask,
- uint32_t value);
-
-/**
- * \brief Reads the pin status.
- *
- * \param[in] dev GPIO device to use for the pin \ref gpio_cmsdk_dev_t
- * \param[in] pin_num Pin number for pin access
- * \param[out] data Bit value read from the IO pin
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum gpio_cmsdk_error_t
-gpio_cmsdk_pin_read(struct gpio_cmsdk_dev_t* dev, uint32_t pin_num, uint32_t *data);
-
-/**
- * \brief Reads the port status.
- *
- * \param[in] dev GPIO device to use for the pins \ref gpio_cmsdk_dev_t
- * \param[in] pin_mask Bitmask of the selected pins
- * \param[out] data Bit values for the mask read from the IO pin
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum gpio_cmsdk_error_t
-gpio_cmsdk_port_read(struct gpio_cmsdk_dev_t* dev, uint32_t pin_mask,
- uint32_t *data);
-
-/**
- * \brief Enables/disables interrupt for the given pin.
- *
- * \param[in] dev GPIO device to initalize \ref gpio_cmsdk_dev_t
- * \param[in] pin_num Pin number to configure
- * \param[in] status Interrupt status \ref gpio_cmsdk_irq_status
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum gpio_cmsdk_error_t
-gpio_cmsdk_set_pin_irq_cfg(struct gpio_cmsdk_dev_t* dev, uint32_t pin_num,
- enum gpio_cmsdk_irq_status_t status);
-
-/**
- * \brief Enables/disables interrupt for the given pins.
- *
- * \param[in] dev GPIO device to use for the pins \ref gpio_cmsdk_dev_t
- * \param[in] pin_mask Bitmask of the pins to configure
- * \param[in] status Interrupt status \ref gpio_cmsdk_irq_status
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum gpio_cmsdk_error_t
-gpio_cmsdk_set_port_irq_cfg(struct gpio_cmsdk_dev_t* dev, uint32_t pin_mask,
- enum gpio_cmsdk_irq_status_t status);
-
-/**
- * \brief Get interrupt status for the given pin.
- *
- * \param[in] dev GPIO device to use for the pin \ref gpio_cmsdk_dev_t
- * \param[in] pin_num Pin number for the access
- * \param[out] status Interrupt status values. If the access is by pin, then
- * the status will be 0 or 1.
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum gpio_cmsdk_error_t
-gpio_cmsdk_get_pin_irq_status(struct gpio_cmsdk_dev_t* dev,
- uint32_t pin_num, uint32_t* status);
-
-/**
- * \brief Get interrupt status for the given port.
- *
- * \param[in] dev GPIO device to use for the pins \ref gpio_cmsdk_dev_t
- * \param[in] pin_mask Bitmask of the pins to configure
- * \param[out] status Interrupt status values. If the access is by pin,
- * then the status will be 0 or 1.
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum gpio_cmsdk_error_t
-gpio_cmsdk_get_port_irq_status(struct gpio_cmsdk_dev_t* dev,
- uint32_t pin_mask, uint32_t* status);
-
-/**
- * \brief Clears gpio interrupt.
- *
- * \param[in] dev GPIO device to initalize \ref gpio_cmsdk_dev_t
- * \param[in] pin_num Pin number.
- *
- * \return Returns error code as specified in \ref gpio_cmsdk_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum gpio_cmsdk_error_t gpio_cmsdk_clear_irq(struct gpio_cmsdk_dev_t* dev,
- uint8_t pin_num);
-
-#ifdef __cplusplus
-}
-#endif
-#endif /* __GPIO_CMSDK_DRV_H__ */
diff --git a/platform/ext/target/musca_a/Native_Driver/mpc_sie200_drv.c b/platform/ext/target/musca_a/Native_Driver/mpc_sie200_drv.c
deleted file mode 100644
index 00dfa86..0000000
--- a/platform/ext/target/musca_a/Native_Driver/mpc_sie200_drv.c
+++ /dev/null
@@ -1,650 +0,0 @@
-/*
- * Copyright (c) 2016-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-#include "mpc_sie200_drv.h"
-
-#include <stddef.h>
-
-#include "cmsis_compiler.h"
-
-#define MPC_SIE200_BLK_CFG_OFFSET 5U
-
-#define MPC_SIE200_CTRL_SEC_RESP (1UL << 4UL) /* MPC fault triggers a
- * bus error */
-#define MPC_SIE200_CTRL_AUTOINCREMENT (1UL << 8UL) /* BLK_IDX auto increment */
-#define MPC_SIE200_CTRL_SEC_LOCK_DOWN (1UL << 31UL) /* MPC Security lock down */
-
-/* ARM MPC interrupt */
-#define MPC_SIE200_INT_EN 1UL
-#define MPC_SIE200_INT_STAT 1UL
-
-/* ARM MPC state definitions */
-#define MPC_SIE200_INITIALIZED (1 << 0)
-
-/* Error code returned by the internal driver functions */
-enum mpc_sie200_intern_error_t{
- MPC_SIE200_INTERN_ERR_NONE = MPC_SIE200_ERR_NONE,
- MPC_SIE200_INTERN_ERR_NOT_IN_RANGE = MPC_SIE200_ERR_NOT_IN_RANGE,
- MPC_SIE200_INTERN_ERR_NOT_ALIGNED = MPC_SIE200_ERR_NOT_ALIGNED,
- MPC_SIE200_INTERN_ERR_INVALID_RANGE = MPC_SIE200_ERR_INVALID_RANGE,
- MPC_INTERN_ERR_RANGE_SEC_ATTR_NON_COMPATIBLE =
- MPC_SIE200_ERR_RANGE_SEC_ATTR_NON_COMPATIBLE,
- /* Calculated block index
- is higher than the maximum allowed by the MPC. It should never
- happen unless the controlled ranges of the MPC are misconfigured
- in the driver or if the IP has not enough LUTs to cover the
- range, due to wrong reported block size for example.
- */
- MPC_SIE200_INTERN_ERR_BLK_IDX_TOO_HIGH = -1,
-
-};
-
-/* ARM MPC memory mapped register access structure */
-struct mpc_sie200_reg_map_t {
- volatile uint32_t ctrl; /* (R/W) MPC Control */
- volatile uint32_t reserved[3];/* Reserved */
- volatile uint32_t blk_max; /* (R/ ) Maximum value of block based index */
- volatile uint32_t blk_cfg; /* (R/ ) Block configuration */
- volatile uint32_t blk_idx; /* (R/W) Index value for accessing block
- * based look up table */
- volatile uint32_t blk_lutn; /* (R/W) Block based gating
- * Look Up Table (LUT) */
- volatile uint32_t int_stat; /* (R/ ) Interrupt state */
- volatile uint32_t int_clear; /* ( /W) Interrupt clear */
- volatile uint32_t int_en; /* (R/W) Interrupt enable */
- volatile uint32_t int_info1; /* (R/ ) Interrupt information 1 */
- volatile uint32_t int_info2; /* (R/ ) Interrupt information 2 */
- volatile uint32_t int_set; /* ( /W) Interrupt set. Debug purpose only */
- volatile uint32_t reserved2[997]; /* Reserved */
- volatile uint32_t pidr4; /* (R/ ) Peripheral ID 4 */
- volatile uint32_t pidr5; /* (R/ ) Peripheral ID 5 */
- volatile uint32_t pidr6; /* (R/ ) Peripheral ID 6 */
- volatile uint32_t pidr7; /* (R/ ) Peripheral ID 7 */
- volatile uint32_t pidr0; /* (R/ ) Peripheral ID 0 */
- volatile uint32_t pidr1; /* (R/ ) Peripheral ID 1 */
- volatile uint32_t pidr2; /* (R/ ) Peripheral ID 2 */
- volatile uint32_t pidr3; /* (R/ ) Peripheral ID 3 */
- volatile uint32_t cidr0; /* (R/ ) Component ID 0 */
- volatile uint32_t cidr1; /* (R/ ) Component ID 1 */
- volatile uint32_t cidr2; /* (R/ ) Component ID 2 */
- volatile uint32_t cidr3; /* (R/ ) Component ID 3 */
-};
-
-/*
- * Checks if the address is controlled by the MPC and returns
- * the range index in which it is contained.
- *
- * \param[in] dev MPC device to initalize \ref mpc_sie200_dev_t
- * \param[in] addr Address to check if it is controlled by MPC.
- * \param[out] addr_range Range index in which it is contained.
- *
- * \return True if the base is controller by the range list, false otherwise.
- */
-static uint32_t is_ctrl_by_range_list(struct mpc_sie200_dev_t* dev, uint32_t addr,
- const struct mpc_sie200_memory_range_t** addr_range)
-{
- uint32_t i;
- const struct mpc_sie200_memory_range_t* range;
-
- for(i = 0; i < dev->data->nbr_of_ranges; i++) {
- range = dev->data->range_list[i];
- if(addr >= range->base && addr <= range->limit) {
- *addr_range = range;
- return 1;
- }
- }
- return 0;
-}
-
-/*
- * Gets the masks selecting the bits in the LUT of the MPC corresponding
- * to the base address (included) up to the limit address (included)
- *
- * \param[in] mpc_dev The MPC device.
- * \param[in] base Address in a range controlled by this MPC
- * (included), aligned on block size.
- * \param[in] limit Address in a range controlled by this MPC
- * (included), aligned on block size.
- * \param[out] range Memory range in which the base address and
- * limit are.
- * \param[out] first_word_idx Index of the first touched word in the LUT.
- * \param[out] nr_words Number of words used in the LUT. If 1, only
- * first_word_mask is valid and limit_word_mask
- * must not be used.
- * \param[out] first_word_mask First word mask in the LUT will be stored here.
- * \param[out] limit_word_mask Limit word mask in the LUT will be stored here.
- *
- * \return Returns error code as specified in \ref mpc_sie200_intern_error_t
- */
-static enum mpc_sie200_intern_error_t get_lut_masks(
- struct mpc_sie200_dev_t* dev,
- const uint32_t base, const uint32_t limit,
- const struct mpc_sie200_memory_range_t** range,
- uint32_t *first_word_idx,
- uint32_t *nr_words,
- uint32_t *first_word_mask,
- uint32_t *limit_word_mask)
-{
- const struct mpc_sie200_memory_range_t* base_range;
- uint32_t block_size;
- uint32_t base_block_idx;
- uint32_t base_word_idx;
- uint32_t blk_max;
- const struct mpc_sie200_memory_range_t* limit_range;
- uint32_t limit_block_idx;
- uint32_t limit_word_idx;
- uint32_t mask;
- uint32_t norm_base;
- uint32_t norm_limit;
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- /*
- * Check that the addresses are within the controlled regions
- * of this MPC
- */
- if(!is_ctrl_by_range_list(dev, base, &base_range) ||
- !is_ctrl_by_range_list(dev, limit, &limit_range)) {
- return MPC_SIE200_INTERN_ERR_NOT_IN_RANGE;
- }
-
- /* Base and limit should be part of the same range */
- if(base_range != limit_range) {
- return MPC_SIE200_INTERN_ERR_INVALID_RANGE;
- }
- *range = base_range;
-
- block_size = (1 << (p_mpc->blk_cfg + MPC_SIE200_BLK_CFG_OFFSET));
-
- /* Base and limit+1 addresses must be aligned on the MPC block size */
- if(base % block_size || (limit+1) % block_size) {
- return MPC_SIE200_INTERN_ERR_NOT_ALIGNED;
- }
-
- /*
- * Get a normalized address that is an offset from the beginning
- * of the lowest range controlled by the MPC
- */
- norm_base = (base - base_range->base) + base_range->range_offset;
- norm_limit = (limit - base_range->base) + base_range->range_offset;
-
- /*
- * Calculate block index and to which 32 bits word it belongs
- */
- limit_block_idx = norm_limit/block_size;
- limit_word_idx = limit_block_idx/32;
-
- base_block_idx = norm_base/block_size;
- base_word_idx = base_block_idx/32;
-
- if(base_block_idx > limit_block_idx) {
- return MPC_SIE200_INTERN_ERR_INVALID_RANGE;
- }
-
- /* Transmit the information to the caller */
- *nr_words = limit_word_idx - base_word_idx + 1;
- *first_word_idx = base_word_idx;
-
- /* Limit to the highest block that can be configured */
- blk_max = p_mpc->blk_max;
-
- if((limit_word_idx > blk_max) || (base_word_idx > blk_max)) {
- return MPC_SIE200_INTERN_ERR_BLK_IDX_TOO_HIGH;
- }
-
- /*
- * Create the mask for the first word to only select the limit N bits
- */
- *first_word_mask = ~((1 << (base_block_idx % 32)) - 1);
-
- /*
- * Create the mask for the limit word to select only the first M bits.
- */
- *limit_word_mask = (1 << ((limit_block_idx+1) % 32)) - 1;
- /*
- * If limit_word_mask is 0, it means that the limit touched block index is
- * the limit in its word, so the limit word mask has all its bits selected
- */
- if(*limit_word_mask == 0) {
- *limit_word_mask = 0xFFFFFFFF;
- }
-
- /*
- * If the blocks to configure are all packed in one word, only
- * touch this word.
- * Code using the computed masks should test if this mask
- * is non-zero, and if so, only use this one instead of the limit_word_mask
- * and first_word_mask.
- * As the only bits that are the same in both masks are the 1 that we want
- * to select, just use XOR to extract them.
- */
- if(base_word_idx == limit_word_idx) {
- mask = ~(*first_word_mask ^ *limit_word_mask);
- *first_word_mask = mask;
- *limit_word_mask = mask;
- }
-
- return MPC_SIE200_INTERN_ERR_NONE;
-}
-
-enum mpc_sie200_error_t mpc_sie200_init(struct mpc_sie200_dev_t* dev,
- const struct mpc_sie200_memory_range_t** range_list,
- uint8_t nbr_of_ranges)
-{
- if((range_list == NULL) || (nbr_of_ranges == 0)) {
- return MPC_SIE200_INVALID_ARG;
- }
-
- dev->data->range_list = range_list;
- dev->data->nbr_of_ranges = nbr_of_ranges;
- dev->data->state = MPC_SIE200_INITIALIZED;
-
- return MPC_SIE200_ERR_NONE;
-}
-
-enum mpc_sie200_error_t mpc_sie200_get_block_size(struct mpc_sie200_dev_t* dev,
- uint32_t* blk_size)
-{
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- if(!(dev->data->state & MPC_SIE200_INITIALIZED)) {
- return MPC_SIE200_NOT_INIT;
- }
-
- if(blk_size == 0) {
- return MPC_SIE200_INVALID_ARG;
- }
-
- /* Calculate the block size in byte according to the manual */
- *blk_size = (1 << (p_mpc->blk_cfg + MPC_SIE200_BLK_CFG_OFFSET));
-
- return MPC_SIE200_ERR_NONE;
-}
-
-enum mpc_sie200_error_t mpc_sie200_config_region(struct mpc_sie200_dev_t* dev,
- const uint32_t base,
- const uint32_t limit,
- enum mpc_sie200_sec_attr_t attr)
-{
- enum mpc_sie200_intern_error_t error;
- uint32_t first_word_idx;
- uint32_t first_word_mask;
- uint32_t i;
- uint32_t limit_word_mask;
- uint32_t limit_word_idx;
- uint32_t nr_words;
- const struct mpc_sie200_memory_range_t* range;
- uint32_t word_value;
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- if(!(dev->data->state & MPC_SIE200_INITIALIZED)) {
- return MPC_SIE200_NOT_INIT;
- }
-
- /* Get the bitmasks used to select the bits in the LUT */
- error = get_lut_masks(dev, base, limit, &range, &first_word_idx, &nr_words,
- &first_word_mask, &limit_word_mask);
-
- limit_word_idx = first_word_idx + nr_words - 1;
-
- if(error != MPC_SIE200_INTERN_ERR_NONE) {
- /* Map internal error code lower than 0 to a generic errpr */
- if(error < 0) {
- return MPC_SIE200_ERR_INVALID_RANGE;
- }
- return (enum mpc_sie200_error_t)error;
- }
-
- /*
- * The memory range should allow accesses in with the wanted security
- * attribute if it requires special attribute for successfull accesses
- */
- if(range->attr != attr) {
- return MPC_SIE200_ERR_RANGE_SEC_ATTR_NON_COMPATIBLE;
- }
-
- /*
- * Starts changing actual configuration so issue DMB to ensure every
- * transaction has completed by now
- */
- __DMB();
-
- /* Set the block index to the first word that will be updated */
- p_mpc->blk_idx = first_word_idx;
-
- /* If only one word needs to be touched in the LUT */
- if(nr_words == 1) {
- word_value = p_mpc->blk_lutn;
- if(attr == MPC_SIE200_SEC_ATTR_NONSECURE) {
- word_value |= first_word_mask;
- } else {
- word_value &= ~first_word_mask;
- }
-
- /*
- * Set the index again because full word read or write could have
- * incremented it
- */
- p_mpc->blk_idx = first_word_idx;
- p_mpc->blk_lutn = word_value;
-
- /* Commit the configuration change */
- __DSB();
- __ISB();
-
- return MPC_SIE200_ERR_NONE;
- }
-
- /* First word */
- word_value = p_mpc->blk_lutn;
- if(attr == MPC_SIE200_SEC_ATTR_NONSECURE) {
- word_value |= first_word_mask;
- } else {
- word_value &= ~first_word_mask;
- }
- /*
- * Set the index again because full word read or write could have
- * incremented it
- */
- p_mpc->blk_idx = first_word_idx;
- /* Partially configure the first word */
- p_mpc->blk_lutn = word_value;
-
- /* Fully configure the intermediate words if there are any */
- for(i=first_word_idx+1; i<limit_word_idx; i++) {
- p_mpc->blk_idx = i;
- if(attr == MPC_SIE200_SEC_ATTR_NONSECURE) {
- p_mpc->blk_lutn = 0xFFFFFFFF;
- } else {
- p_mpc->blk_lutn = 0x00000000;
- }
- }
-
- /* Partially configure the limit word */
- p_mpc->blk_idx = limit_word_idx;
- word_value = p_mpc->blk_lutn;
- if(attr == MPC_SIE200_SEC_ATTR_NONSECURE) {
- word_value |= limit_word_mask;
- } else {
- word_value &= ~limit_word_mask;
- }
- p_mpc->blk_idx = limit_word_idx;
- p_mpc->blk_lutn = word_value;
-
- /* Commit the configuration change */
- __DSB();
- __ISB();
-
- return MPC_SIE200_ERR_NONE;
-}
-
-enum mpc_sie200_error_t mpc_sie200_get_region_config(
- struct mpc_sie200_dev_t* dev,
- uint32_t base, uint32_t limit,
- enum mpc_sie200_sec_attr_t* attr)
-{
- enum mpc_sie200_sec_attr_t attr_prev;
- uint32_t block_size;
- uint32_t block_size_mask;
- enum mpc_sie200_intern_error_t error;
- uint32_t first_word_idx;
- uint32_t first_word_mask;
- uint32_t i;
- uint32_t limit_word_idx;
- uint32_t limit_word_mask;
- uint32_t nr_words;
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
- const struct mpc_sie200_memory_range_t* range;
- uint32_t word_value;
-
- if(!(dev->data->state & MPC_SIE200_INITIALIZED)) {
- return MPC_SIE200_NOT_INIT;
- }
-
- if(attr == 0) {
- return MPC_SIE200_INVALID_ARG;
- }
-
- /*
- * Initialize the security attribute to mixed in case of early
- * termination of this function. A caller that does not check the
- * returned error will act as if it does not know anything about the
- * region queried, which is the safest bet
- */
- *attr = MPC_SIE200_SEC_ATTR_MIXED;
-
- /*
- * If the base and limit are not aligned, align them and make sure
- * that the resulting region fully includes the original region
- */
- block_size = (1 << (p_mpc->blk_cfg + MPC_SIE200_BLK_CFG_OFFSET));
-
- block_size_mask = block_size - 1;
- base &= ~(block_size_mask);
- limit &= ~(block_size_mask);
- limit += block_size - 1; /* Round to the upper block address,
- * and then remove one to get the preceding
- * address.
- */
-
- /* Get the bitmasks used to select the bits in the LUT */
- error = get_lut_masks(dev, base, limit, &range, &first_word_idx, &nr_words,
- &first_word_mask, &limit_word_mask);
-
- limit_word_idx = first_word_idx+nr_words - 1;
-
- if(error != MPC_SIE200_INTERN_ERR_NONE) {
- /* Map internal error code lower than 0 to generic error */
- if(error < 0) {
- return MPC_SIE200_ERR_INVALID_RANGE;
- }
- return (enum mpc_sie200_error_t)error;
- }
-
- /* Set the block index to the first word that will be updated */
- p_mpc->blk_idx = first_word_idx;
-
- /* If only one word needs to be touched in the LUT */
- if(nr_words == 1) {
- word_value = p_mpc->blk_lutn;
- word_value &= first_word_mask;
- if(word_value == 0) {
- *attr = MPC_SIE200_SEC_ATTR_SECURE;
- /*
- * If there are differences between the mask and the word value,
- * it means that the security attributes of blocks are mixed
- */
- } else if(word_value ^ first_word_mask) {
- *attr = MPC_SIE200_SEC_ATTR_MIXED;
- } else {
- *attr = MPC_SIE200_SEC_ATTR_NONSECURE;
- }
- return MPC_SIE200_ERR_NONE;
- }
-
- /* Get the partial configuration of the first word */
- word_value = p_mpc->blk_lutn & first_word_mask;
- if(word_value == 0x00000000) {
- *attr = MPC_SIE200_SEC_ATTR_SECURE;
- } else if(word_value ^ first_word_mask) {
- *attr = MPC_SIE200_SEC_ATTR_MIXED;
- /*
- * Bail out as the security attribute will be the same regardless
- * of the configuration of other blocks
- */
- return MPC_SIE200_ERR_NONE;
- } else {
- *attr = MPC_SIE200_SEC_ATTR_NONSECURE;
- }
- /*
- * Store the current found attribute, to check that all the blocks indeed
- * have the same security attribute.
- */
- attr_prev = *attr;
-
- /* Get the configuration of the intermediate words if there are any */
- for(i=first_word_idx+1; i<limit_word_idx; i++) {
- p_mpc->blk_idx = i;
- word_value = p_mpc->blk_lutn;
- if(word_value == 0x00000000) {
- *attr = MPC_SIE200_SEC_ATTR_SECURE;
- } else if(word_value == 0xFFFFFFFF) {
- *attr = MPC_SIE200_SEC_ATTR_NONSECURE;
- } else {
- *attr = MPC_SIE200_SEC_ATTR_MIXED;
- return MPC_SIE200_ERR_NONE;
- }
-
- /* If the attribute is different than the one found before, bail out */
- if(*attr != attr_prev) {
- *attr = MPC_SIE200_SEC_ATTR_MIXED;
- return MPC_SIE200_ERR_NONE;
- }
- attr_prev = *attr;
- }
-
- /* Get the partial configuration of the limit word */
- p_mpc->blk_idx = limit_word_idx;
- word_value = p_mpc->blk_lutn & limit_word_mask;
- if(word_value == 0x00000000) {
- *attr = MPC_SIE200_SEC_ATTR_SECURE;
- } else if(word_value ^ first_word_mask) {
- *attr = MPC_SIE200_SEC_ATTR_MIXED;
- return MPC_SIE200_ERR_NONE;
- } else {
- *attr = MPC_SIE200_SEC_ATTR_NONSECURE;
- }
-
- if(*attr != attr_prev) {
- *attr = MPC_SIE200_SEC_ATTR_MIXED;
- return MPC_SIE200_ERR_NONE;
- }
-
- return MPC_SIE200_ERR_NONE;
-}
-
-enum mpc_sie200_error_t mpc_sie200_get_ctrl(struct mpc_sie200_dev_t* dev,
- uint32_t* ctrl_val)
-{
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- if(!(dev->data->state & MPC_SIE200_INITIALIZED)) {
- return MPC_SIE200_NOT_INIT;
- }
-
- if(ctrl_val == 0) {
- return MPC_SIE200_INVALID_ARG;
- }
-
- *ctrl_val = p_mpc->ctrl;
-
- return MPC_SIE200_ERR_NONE;
-}
-
-enum mpc_sie200_error_t mpc_sie200_set_ctrl(struct mpc_sie200_dev_t* dev,
- uint32_t mpc_ctrl)
-{
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- if(!(dev->data->state & MPC_SIE200_INITIALIZED)) {
- return MPC_SIE200_NOT_INIT;
- }
-
- p_mpc->ctrl = mpc_ctrl;
-
- return MPC_SIE200_ERR_NONE;
-}
-
-enum mpc_sie200_error_t mpc_sie200_get_sec_resp(struct mpc_sie200_dev_t* dev,
- enum mpc_sie200_sec_resp_t* sec_rep)
-{
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- if(!(dev->data->state & MPC_SIE200_INITIALIZED)) {
- return MPC_SIE200_NOT_INIT;
- }
-
- if(sec_rep == 0) {
- return MPC_SIE200_INVALID_ARG;
- }
-
- if(p_mpc->ctrl & MPC_SIE200_CTRL_SEC_RESP) {
- *sec_rep = MPC_SIE200_RESP_BUS_ERROR;
- return MPC_SIE200_ERR_NONE;
- }
-
- *sec_rep = MPC_SIE200_RESP_RAZ_WI;
-
- return MPC_SIE200_ERR_NONE;
-}
-
-enum mpc_sie200_error_t mpc_sie200_irq_enable(struct mpc_sie200_dev_t* dev)
-{
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- if(!(dev->data->state & MPC_SIE200_INITIALIZED)) {
- return MPC_SIE200_NOT_INIT;
- }
-
- p_mpc->int_en |= MPC_SIE200_INT_EN;
-
- return MPC_SIE200_ERR_NONE;
-}
-
-void mpc_sie200_irq_disable(struct mpc_sie200_dev_t* dev)
-{
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- p_mpc->int_en &= ~MPC_SIE200_INT_EN;
-}
-
-void mpc_sie200_clear_irq(struct mpc_sie200_dev_t* dev)
-{
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- p_mpc->int_clear = MPC_SIE200_INT_EN;
-}
-
-uint32_t mpc_sie200_irq_state(struct mpc_sie200_dev_t* dev)
-{
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- return (p_mpc->int_stat & MPC_SIE200_INT_STAT);
-}
-
-enum mpc_sie200_error_t mpc_sie200_lock_down(struct mpc_sie200_dev_t* dev)
-{
- struct mpc_sie200_reg_map_t* p_mpc =
- (struct mpc_sie200_reg_map_t*)dev->cfg->base;
-
- if(!(dev->data->state & MPC_SIE200_INITIALIZED)) {
- return MPC_SIE200_NOT_INIT;
- }
-
- p_mpc->ctrl |= (MPC_SIE200_CTRL_AUTOINCREMENT
- | MPC_SIE200_CTRL_SEC_LOCK_DOWN);
-
- return MPC_SIE200_ERR_NONE;
-}
diff --git a/platform/ext/target/musca_a/Native_Driver/mpc_sie200_drv.h b/platform/ext/target/musca_a/Native_Driver/mpc_sie200_drv.h
deleted file mode 100644
index a691e78..0000000
--- a/platform/ext/target/musca_a/Native_Driver/mpc_sie200_drv.h
+++ /dev/null
@@ -1,280 +0,0 @@
-/*
- * Copyright (c) 2016-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file mpc_sie200_drv.h
- * \brief Generic driver for ARM SIE 200 Memory Protection
- * Controllers (MPC).
- */
-
-#ifndef __MPC_SIE_200_DRV_H__
-#define __MPC_SIE_200_DRV_H__
-
-#include <stdint.h>
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/* Error code returned by the driver functions */
-enum mpc_sie200_error_t {
- MPC_SIE200_ERR_NONE, /*!< No error */
- MPC_SIE200_INVALID_ARG, /*!< MPC invalid input arguments */
- MPC_SIE200_NOT_INIT, /*!< MPC not initialized */
- MPC_SIE200_ERR_NOT_IN_RANGE, /*!< Address does not belong to a range
- * controlled by the MPC */
- MPC_SIE200_ERR_NOT_ALIGNED, /*!< Address is not aligned on the block size
- * of this MPC */
- MPC_SIE200_ERR_INVALID_RANGE, /*!< The given address range to configure
- * is invalid. This could be because:
- * - The base and limit swapped
- * - The base and limit addresses
- * are in different ranges */
- MPC_SIE200_ERR_RANGE_SEC_ATTR_NON_COMPATIBLE, /*!< The given range cannot be
- * accessed with the wanted
- * security attributes */
-};
-
-/* Security attribute used in various place of the API */
-enum mpc_sie200_sec_attr_t {
- MPC_SIE200_SEC_ATTR_SECURE, /*!< Secure attribute */
- MPC_SIE200_SEC_ATTR_NONSECURE, /*!< Non-secure attribute */
- /*!< Used when getting the configuration of a memory range and some blocks
- * are secure whereas some other are non secure */
- MPC_SIE200_SEC_ATTR_MIXED,
-};
-
-/* What can happen when trying to do an illegal memory access */
-enum mpc_sie200_sec_resp_t {
- MPC_SIE200_RESP_RAZ_WI, /*!< Read As Zero, Write Ignored */
- MPC_SIE200_RESP_BUS_ERROR /*!< Bus error */
-};
-
-/* Description of a memory range controlled by the MPC */
-struct mpc_sie200_memory_range_t {
- const uint32_t base; /*!< Base address (included in the range) */
- const uint32_t limit; /*!< Limit address (included in the range) */
- const uint32_t range_offset; /*!< Offset of current range area to the 0
- point of the whole area (the sum of the
- sizes of the previous memory ranges
- covered by the same MPC) */
- const enum mpc_sie200_sec_attr_t attr; /*!< Optional security attribute
- needed to be matched when
- accessing this range.
- For example, the non-secure
- alias of a memory region can not
- be accessed using secure access,
- and configuring the MPC to
- secure using that range will not
- be permitted by the driver. */
-};
-
-/* ARM MPC SIE 200 device configuration structure */
-struct mpc_sie200_dev_cfg_t {
- const uint32_t base; /*!< MPC base address */
-};
-
-/* ARM MPC SIE 200 device data structure */
-struct mpc_sie200_dev_data_t {
- const struct mpc_sie200_memory_range_t** range_list; /*!< Array of pointers
- to memory ranges
- controlled by
- the MPC */
- uint8_t nbr_of_ranges; /*!< Number of memory ranges in the list */
- uint8_t state; /*!< Indicates if the MPC driver
- is initialized and enabled */
- uint16_t reserved; /*!< 32 bits alignment */
-};
-
-/* ARM MPC SIE 200 device structure */
-struct mpc_sie200_dev_t {
- const struct mpc_sie200_dev_cfg_t* const cfg; /*!< MPC configuration */
- struct mpc_sie200_dev_data_t* const data; /*!< MPC data */
-};
-
-/**
- * \brief Initializes a MPC device.
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- * \param[in] range_list List of memory ranges controller by the MPC
- * (\ref mpc_sie200_memory_range_t). This list can not
- * freed after the initializations.
- * \param[in] nbr_of_ranges Number of memory ranges
- *
- * \return Returns error code as specified in \ref mpc_sie200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpc_sie200_error_t mpc_sie200_init(struct mpc_sie200_dev_t* dev,
- const struct mpc_sie200_memory_range_t** range_list,
- uint8_t nbr_of_ranges);
-
-/**
- * \brief Gets MPC block size. All regions must be aligned on this block
- * size (base address and limit+1 address).
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- * \param[out] blk_size MPC block size
- *
- * \return Returns error code as specified in \ref mpc_sie200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpc_sie200_error_t mpc_sie200_get_block_size(struct mpc_sie200_dev_t* dev,
- uint32_t* blk_size);
-
-/**
- * \brief Configures a memory region (base and limit included).
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- * \param[in] base Base address of the region to poll. This bound is
- * included. It does not need to be aligned in any way.
- *
- * \param[in] limit Limit address of the region to poll. This bound is
- * included. (limit+1) does not need to be aligned
- * in any way.
- * \param[in] attr Security attribute of the region. If the region has mixed
- * secure/non-secure, a special value is returned
- * (\ref mpc_sie200_sec_attr_t).
- *
- * In case base and limit+1 addresses are not aligned on
- * the block size, the enclosing region with base and
- * limit+1 aligned on block size will be queried.
- * In case of early termination of the function (error), the
- * security attribute will be set to MPC_SIE200_ATTR_MIXED.
- *
- * \return Returns error code as specified in \ref mpc_sie200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpc_sie200_error_t mpc_sie200_config_region(struct mpc_sie200_dev_t* dev,
- const uint32_t base,
- const uint32_t limit,
- enum mpc_sie200_sec_attr_t attr);
-
-/**
- * \brief Gets a memory region configuration(base and limit included).
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- * \param[in] base Base address of the region to get the configuration.
- * \param[in] limit Limit address of the region to get the configuration.
- * \param[out] attr Security attribute of the region
- * \ref mpc_sie200_sec_attr_t
- *
- * \return Returns error code as specified in \ref mpc_sie200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpc_sie200_error_t mpc_sie200_get_region_config(
- struct mpc_sie200_dev_t* dev,
- uint32_t base,
- uint32_t limit,
- enum mpc_sie200_sec_attr_t* attr);
-
-/**
- * \brief Gets the MPC control value.
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- * \param[out] ctrl_val Current MPC control value.
- *
- * \return Returns error code as specified in \ref mpc_sie200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpc_sie200_error_t mpc_sie200_get_ctrl(struct mpc_sie200_dev_t* dev,
- uint32_t* ctrl_val);
-
-/**
- * \brief Sets the MPC control value.
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- * \param[in] mpc_ctrl New MPC control value
- *
- * \return Returns error code as specified in \ref mpc_sie200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpc_sie200_error_t mpc_sie200_set_ctrl(struct mpc_sie200_dev_t* dev,
- uint32_t mpc_ctrl);
-
-/**
- * \brief Gets the configured secure response.
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- * \param[out] sec_rep Configured secure response (\ref mpc_sie200_sec_resp_t).
- *
- * \return Returns error code as specified in \ref mpc_sie200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpc_sie200_error_t mpc_sie200_get_sec_resp(struct mpc_sie200_dev_t* dev,
- enum mpc_sie200_sec_resp_t* sec_rep);
-
-/**
- * \brief Enables MPC interrupt.
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- *
- * \return Returns error code as specified in \ref mpc_sie200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpc_sie200_error_t mpc_sie200_irq_enable(struct mpc_sie200_dev_t* dev);
-
-/**
- * \brief Disables MPC interrupt
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void mpc_sie200_irq_disable(struct mpc_sie200_dev_t* dev);
-
-/**
- * \brief Clears MPC interrupt.
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void mpc_sie200_clear_irq(struct mpc_sie200_dev_t* dev);
-
-/**
- * \brief Returns the MPC interrupt state.
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- *
- * \return Returns 1 if the interrupt is active, 0 otherwise.
- *
- * \note This function doesn't check if dev is NULL.
- */
-uint32_t mpc_sie200_irq_state(struct mpc_sie200_dev_t* dev);
-
-/**
- * \brief Locks down the MPC configuration.
- *
- * \param[in] dev MPC device \ref mpc_sie200_dev_t
- *
- * \return Returns error code as specified in \ref mpc_sie200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpc_sie200_error_t mpc_sie200_lock_down(struct mpc_sie200_dev_t* dev);
-
-#ifdef __cplusplus
-}
-#endif
-#endif /* __MPC_SIE_200_DRV_H__ */
diff --git a/platform/ext/target/musca_a/Native_Driver/mpu_armv8m_drv.c b/platform/ext/target/musca_a/Native_Driver/mpu_armv8m_drv.c
deleted file mode 100644
index ad9efab..0000000
--- a/platform/ext/target/musca_a/Native_Driver/mpu_armv8m_drv.c
+++ /dev/null
@@ -1,152 +0,0 @@
-/*
- * Copyright (c) 2017-2019, Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#include "mpu_armv8m_drv.h"
-#include "cmsis.h"
-
-/*
- * FixMe:
- * This is a beta quality driver for MPU in v8M. To be finalized.
- */
-
-enum mpu_armv8m_error_t mpu_armv8m_enable(struct mpu_armv8m_dev_t *dev,
- uint32_t privdef_en,
- uint32_t hfnmi_en)
-{
- /*No error checking*/
-
- MPU_Type *mpu = (MPU_Type *)dev->base;
-
- /*
- * FixMe: Set 3 pre-defined MAIR_ATTR for memory. The attributes come
- * from default memory map, need to check if fine-tune is necessary.
- *
- * MAIR0_0: Peripheral, Device-nGnRE.
- * MAIR0_1: Code, WT RA. Same attr for Outer and Inner.
- * MAIR0_2: SRAM, WBWA RA. Same attr for Outer and Inner.
- */
- mpu->MAIR0 = (MPU_ARMV8M_MAIR_ATTR_DEVICE_VAL << MPU_MAIR0_Attr0_Pos) |
- (MPU_ARMV8M_MAIR_ATTR_CODE_VAL << MPU_MAIR0_Attr1_Pos) |
- (MPU_ARMV8M_MAIR_ATTR_DATA_VAL << MPU_MAIR0_Attr2_Pos);
-
- mpu->CTRL =
- (privdef_en ? MPU_CTRL_PRIVDEFENA_Msk : 0) |
- (hfnmi_en ? MPU_CTRL_HFNMIENA_Msk : 0);
-
- /*Ensure all configuration is written before enable*/
-
- mpu->CTRL |= MPU_CTRL_ENABLE_Msk;
-
- /* Enable MPU before next instruction */
- __DSB();
- __ISB();
- return MPU_ARMV8M_OK;
-}
-
-enum mpu_armv8m_error_t mpu_armv8m_disable(struct mpu_armv8m_dev_t *dev)
-{
- MPU_Type *mpu = (MPU_Type *)dev->base;
-
- /* Reset all fields as enable does full setup */
- mpu->CTRL = 0;
-
- return MPU_ARMV8M_OK;
-}
-
-
-enum mpu_armv8m_error_t mpu_armv8m_region_enable(
- struct mpu_armv8m_dev_t *dev,
- struct mpu_armv8m_region_cfg_t *region_cfg)
-{
- MPU_Type *mpu = (MPU_Type *)dev->base;
-
- enum mpu_armv8m_error_t ret_val = MPU_ARMV8M_OK;
- uint32_t ctrl_before;
- uint32_t base_cfg;
- uint32_t limit_cfg;
-
- /*FIXME : Add complete error checking*/
- if ((region_cfg->region_base & ~MPU_RBAR_BASE_Msk) != 0) {
- return MPU_ARMV8M_ERROR;
- }
- /* region_limit doesn't need to be aligned but the scatter
- * file needs to be setup to ensure that partitions do not overlap.
- */
-
- ctrl_before = mpu->CTRL;
- mpu->CTRL = 0;
-
- mpu->RNR = region_cfg->region_nr & MPU_RNR_REGION_Msk;
-
- /* This 0s the lower bits of the base address */
- base_cfg = region_cfg->region_base & MPU_RBAR_BASE_Msk;
- base_cfg |= (region_cfg->attr_sh << MPU_RBAR_SH_Pos) & MPU_RBAR_SH_Msk;
- base_cfg |= (region_cfg->attr_access << MPU_RBAR_AP_Pos) & MPU_RBAR_AP_Msk;
- base_cfg |= (region_cfg->attr_exec << MPU_RBAR_XN_Pos) & MPU_RBAR_XN_Msk;
-
- mpu->RBAR = base_cfg;
-
- /*This 0s the lower bits of base address but they are treated as 1 */
- limit_cfg = (region_cfg->region_limit-1) & MPU_RLAR_LIMIT_Msk;
-
- limit_cfg |= (region_cfg->region_attridx << MPU_RLAR_AttrIndx_Pos) &
- MPU_RLAR_AttrIndx_Msk;
-
- limit_cfg |= MPU_RLAR_EN_Msk;
-
- mpu->RLAR = limit_cfg;
-
- /*Restore main MPU control*/
- mpu->CTRL = ctrl_before;
-
- /* Enable MPU before the next instruction */
- __DSB();
- __ISB();
-
- return ret_val;
-}
-
-
-enum mpu_armv8m_error_t mpu_armv8m_region_disable(
- struct mpu_armv8m_dev_t *dev,
- uint32_t region_nr)
-{
-
- MPU_Type *mpu = (MPU_Type *)dev->base;
-
- enum mpu_armv8m_error_t ret_val = MPU_ARMV8M_OK;
- uint32_t ctrl_before;
-
- /*FIXME : Add complete error checking*/
-
- ctrl_before = mpu->CTRL;
- mpu->CTRL = 0;
-
- mpu->RNR = region_nr & MPU_RNR_REGION_Msk;
-
- mpu->RBAR = 0;
- mpu->RLAR = 0;
-
- /*Restore main MPU control*/
- mpu->CTRL = ctrl_before;
-
- return ret_val;
-}
-
-enum mpu_armv8m_error_t mpu_armv8m_clean(struct mpu_armv8m_dev_t *dev)
-{
- MPU_Type *mpu = (MPU_Type *)dev->base;
- uint32_t i = (mpu->TYPE & MPU_TYPE_DREGION_Msk) >> MPU_TYPE_DREGION_Pos;
-
- while (i > 0) {
- mpu_armv8m_region_disable(dev, i-1);
- i--;
- }
-
- return MPU_ARMV8M_OK;
-
-}
diff --git a/platform/ext/target/musca_a/Native_Driver/mpu_armv8m_drv.h b/platform/ext/target/musca_a/Native_Driver/mpu_armv8m_drv.h
deleted file mode 100644
index d427604..0000000
--- a/platform/ext/target/musca_a/Native_Driver/mpu_armv8m_drv.h
+++ /dev/null
@@ -1,143 +0,0 @@
-/*
- * Copyright (c) 2017-2019, Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#ifndef __MPU_ARMV8M_DRV_H__
-#define __MPU_ARMV8M_DRV_H__
-
-#include <stdint.h>
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-#define PRIVILEGED_DEFAULT_ENABLE 1
-#define HARDFAULT_NMI_ENABLE 1
-
-/* MAIR_ATTR */
-#define MPU_ARMV8M_MAIR_ATTR_DEVICE_VAL 0x04
-#define MPU_ARMV8M_MAIR_ATTR_DEVICE_IDX 0
-#define MPU_ARMV8M_MAIR_ATTR_CODE_VAL 0xAA
-#define MPU_ARMV8M_MAIR_ATTR_CODE_IDX 1
-#define MPU_ARMV8M_MAIR_ATTR_DATA_VAL 0xFF
-#define MPU_ARMV8M_MAIR_ATTR_DATA_IDX 2
-
-struct mpu_armv8m_dev_t {
- const uint32_t base;
-};
-
-enum mpu_armv8m_error_t {
- MPU_ARMV8M_OK,
- MPU_ARMV8M_ERROR
-};
-
-enum mpu_armv8m_attr_exec_t {
- MPU_ARMV8M_XN_EXEC_OK,
- MPU_ARMV8M_XN_EXEC_NEVER
-};
-
-enum mpu_armv8m_attr_access_t {
- MPU_ARMV8M_AP_RW_PRIV_ONLY,
- MPU_ARMV8M_AP_RW_PRIV_UNPRIV,
- MPU_ARMV8M_AP_RO_PRIV_ONLY,
- MPU_ARMV8M_AP_RO_PRIV_UNPRIV
-};
-
-enum mpu_armv8m_attr_shared_t {
- MPU_ARMV8M_SH_NONE,
- MPU_ARMV8M_SH_UNUSED,
- MPU_ARMV8M_SH_OUTER,
- MPU_ARMV8M_SH_INNER
-};
-
-struct mpu_armv8m_region_cfg_t {
- uint32_t region_nr;
- uint32_t region_base;
- uint32_t region_limit;
- uint32_t region_attridx;
- enum mpu_armv8m_attr_exec_t attr_exec;
- enum mpu_armv8m_attr_access_t attr_access;
- enum mpu_armv8m_attr_shared_t attr_sh;
-};
-
-struct mpu_armv8m_region_cfg_raw_t {
- uint32_t region_nr;
- uint32_t region_base;
- uint32_t region_limit;
-};
-
-
-/**
- * \brief Enable MPU
- *
- * \param[in] dev MPU device \ref mpu_armv8m_dev_t
- * \param[in] privdef_en privilege default region 1:enable 0:disable
- * \param[in] hfnmi_en mpu for hard fault & nmi 1:enable 0:disable
- *
- * \return Error code \ref mpu_armv8m_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-
-enum mpu_armv8m_error_t mpu_armv8m_enable(struct mpu_armv8m_dev_t *dev,
- uint32_t privdef_en,
- uint32_t hfnmi_en);
-
-/**
- * \brief Disable MPU
- *
- * \param[in] dev MPU device \ref mpu_armv8m_dev_t
- *
- * \return Error code \ref arm_mpu_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpu_armv8m_error_t mpu_armv8m_disable(struct mpu_armv8m_dev_t *dev);
-
-/**
- * \brief Disable MPU and clean all regions
- *
- * \param[in] dev MPU device \ref mpu_armv8m_dev_t
- *
- * \return Error code \ref arm_mpu_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpu_armv8m_error_t mpu_armv8m_clean(struct mpu_armv8m_dev_t *dev);
-
-/**
- * \brief Enable MPU Region
- *
- * \param[in] dev MPU device \ref mpu_armv8m_dev_t
- * \param[in] region_cfg MPU region config \ref mpu_armv8m_region_cfg_t
- *
- * \return Error code \ref arm_mpu_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpu_armv8m_error_t mpu_armv8m_region_enable(
- struct mpu_armv8m_dev_t *dev,
- struct mpu_armv8m_region_cfg_t *region_cfg);
-
-/**
- * \brief Disable MPU Region
- *
- * \param[in] dev MPU device \ref mpu_armv8m_dev_t
- * \param[in] region_nr Region number
- *
- * \return Error code \ref arm_mpu_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum mpu_armv8m_error_t mpu_armv8m_region_disable(
- struct mpu_armv8m_dev_t *dev,
- uint32_t region_nr);
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __MPU_ARMV8M_DRV_H__ */
diff --git a/platform/ext/target/musca_a/Native_Driver/musca_a1_scc_drv.c b/platform/ext/target/musca_a/Native_Driver/musca_a1_scc_drv.c
deleted file mode 100644
index ad1a185..0000000
--- a/platform/ext/target/musca_a/Native_Driver/musca_a1_scc_drv.c
+++ /dev/null
@@ -1,250 +0,0 @@
-/*
- * Copyright (c) 2017-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include "musca_a1_scc_drv.h"
-
-struct musca_a1_scc_reg_map_t {
- volatile uint32_t reset_ctrl; /* 0x00 RW Reset Control Register */
- volatile uint32_t clk_ctrl; /* 0x04 RW Clock Control Register*/
- volatile uint32_t pwr_ctrl; /* 0x08 RW Power Control Register*/
- volatile uint32_t pll_ctrl; /* 0x0C RW Power Control Register */
- volatile uint32_t dbg_ctrl; /* 0x10 RW Debug Control Register */
- volatile uint32_t sram_ctrl; /* 0x14 RW SRAM Control Register */
- volatile uint32_t intr_ctrl; /* 0x18 RW Interupt Control Register */
- volatile uint32_t reserved1; /* 0x1C RW reserved */
- volatile uint32_t cpu0_vtor_sram; /* 0x20 RW Reset vector for CPU0 Secure Mode */
- volatile uint32_t cpu0_vtor_flash; /* 0x24 RW Reset vector for CPU0 Secure Mode */
- volatile uint32_t cpu1_vtor_sram; /* 0x28 RW Reset vector for CPU1 Secure Mode */
- volatile uint32_t cpu1_vtor_flash; /* 0x2C RW Reset vector for CPU0 Secure Mode */
- volatile uint32_t iomux_main_insel; /* 0x30 RW Main function in data select */
- volatile uint32_t iomux_main_outsel; /* 0x34 RW Main function out data select */
- volatile uint32_t iomux_main_oensel; /* 0x38 RW Main function out enable select */
- volatile uint32_t iomux_main_default_in; /* 0x3C RW Main function default in select */
- volatile uint32_t iomux_altf1_insel; /* 0x40 RW Alt function 1 in data select */
- volatile uint32_t iomux_altf1_outsel; /* 0x44 RW Alt function 1 out data select */
- volatile uint32_t iomux_altf1_oensel; /* 0x48 RW Alt function 1 out enable select */
- volatile uint32_t iomux_altf1_default_in; /* 0x4C RW Alt function 1 default in select */
- volatile uint32_t iomux_altf2_insel; /* 0x50 RW Alt function 2 in data select */
- volatile uint32_t iomux_altf2_outsel; /* 0x54 RW Alt function 2 out data select */
- volatile uint32_t iomux_altf2_oensel; /* 0x58 RW Alt function 2 out enable select */
- volatile uint32_t iomux_altf2_default_in; /* 0x5C RW Alt function 2 default in select */
- volatile uint32_t pvt_ctrl; /* 0x60 RW PVT control register */
- volatile uint32_t spare0; /* 0x64 RW reserved */
- volatile uint32_t iopad_ds0; /* 0x68 RW Drive Select 0 */
- volatile uint32_t iopad_ds1; /* 0x6C RW Drive Select 1 */
- volatile uint32_t iopad_pe; /* 0x70 RW Pull Enable */
- volatile uint32_t iopad_ps; /* 0x74 RW Pull Select */
- volatile uint32_t iopad_sr; /* 0x78 RW Slew Select */
- volatile uint32_t iopad_is; /* 0x7C RW Input Select */
- volatile uint32_t sram_rw_margine; /* 0x80 RW reserved */
- volatile uint32_t static_conf_sig0; /* 0x84 RW Static configuration */
- volatile uint32_t static_conf_sig1; /* 0x88 RW Static configuration */
- volatile uint32_t req_set; /* 0x8C RW External Event Enable */
- volatile uint32_t req_clear; /* 0x90 RW External Event Clear */
- volatile uint32_t iomux_altf3_insel; /* 0x94 RW Alt function 3 in data select */
- volatile uint32_t iomux_altf3_outsel; /* 0x98 RW Alt function 3 out data select */
- volatile uint32_t iomux_altf3_oensel; /* 0x9C RW Alt function 3 out enable select */
- volatile uint32_t iomux_altf3_default_in; /* 0xA0 RW Alt function 3 default in select */
- volatile uint32_t pcsm_ctrl_override; /* 0xA4 RW Q-Channels QACTIVE Override */
- volatile uint32_t pd_cpu0_iso_override; /* 0xA8 RW CPU0 Isolation Override */
- volatile uint32_t pd_cpu1_iso_override; /* 0xAC RW CPU1 Isolation Override */
- volatile uint32_t sys_sram_rw_assist0; /* 0xB0 RW CPU0 icache sram ldata */
- volatile uint32_t sys_sram_rw_assist1; /* 0xB4 RW CPU0 icache sram tag */
- volatile uint32_t sys_sram_rw_assist2; /* 0xB8 RW CPU1 icache sram ldata */
- volatile uint32_t sys_sram_rw_assist3; /* 0xBC RW CPU1 icache sram tag */
- volatile uint32_t sys_sram_rw_assist4; /* 0xC0 RW System sram */
- volatile uint32_t sys_sram_rw_assist5; /* 0xC4 RW System sram */
- volatile uint32_t reserved2[3]; /* reserved */
- volatile uint32_t crypto_sram_rw_assist0; /* 0xD4 RW Crypto ram */
- volatile uint32_t crypto_sram_rw_assist1; /* 0xD8 RW Crypto sec sram */
- volatile uint32_t crypto_sram_rw_assist2; /* 0xDC RW Reserved */
- volatile uint32_t req_edge_sel; /* 0xC0 RW Power clock request edge select */
- volatile uint32_t req_enable; /* 0xC4 RW Power clock request enable */
- volatile uint32_t reserved3[28]; /* reserved */
- volatile uint32_t chip_id; /* 0x100 RO Chip ID 0x0797_0477 */
- volatile uint32_t clock_status; /* 0x104 RO Clock status */
- volatile uint32_t io_in_status; /* 0x108 RO I/O in status */
-};
-
-/**
- * \brief Clears selected alternate functions for selected pins
- *
- * \param[in] dev SCC registers base address \ref musca_a1_scc_reg_map_t
- * \param[in] func_mask Bitmask of alternate functions to clear
- * \ref gpio_altfunc_mask_t
- * \param[in] pin_mask Pin mask for the alternate functions
- */
-static void scc_clear_alt_func(struct musca_a1_scc_reg_map_t* scc_regs,
- enum gpio_altfunc_mask_t func_mask,
- uint32_t pin_mask)
-{
- if (func_mask & GPIO_MAIN_FUNC_MASK) {
- scc_regs->iomux_main_insel &= ~pin_mask;
- scc_regs->iomux_main_outsel &= ~pin_mask;
- scc_regs->iomux_main_oensel &= ~pin_mask;
- }
- if (func_mask & GPIO_ALTFUNC_1_MASK) {
- scc_regs->iomux_altf1_insel &= ~pin_mask;
- scc_regs->iomux_altf1_outsel &= ~pin_mask;
- scc_regs->iomux_altf1_oensel &= ~pin_mask;
- }
- if (func_mask & GPIO_ALTFUNC_2_MASK) {
- scc_regs->iomux_altf2_insel &= ~pin_mask;
- scc_regs->iomux_altf2_outsel &= ~pin_mask;
- scc_regs->iomux_altf2_oensel &= ~pin_mask;
- }
- if (func_mask & GPIO_ALTFUNC_3_MASK) {
- scc_regs->iomux_altf3_insel &= ~pin_mask;
- scc_regs->iomux_altf3_outsel &= ~pin_mask;
- scc_regs->iomux_altf3_oensel &= ~pin_mask;
- }
-}
-
-void musca_a1_scc_set_alt_func(struct musca_a1_scc_dev_t* dev,
- enum gpio_altfunc_t altfunc, uint32_t pin_mask)
-{
- struct musca_a1_scc_reg_map_t* scc_regs =
- (struct musca_a1_scc_reg_map_t*) dev->cfg->base;
- enum gpio_altfunc_mask_t altfunc_to_clear = GPIO_ALTFUNC_NONE;
- volatile uint32_t *insel = NULL;
- volatile uint32_t *outsel = NULL;
- volatile uint32_t *oensel = NULL;
-
- if (altfunc >= GPIO_ALTFUNC_MAX) {
- /* If no altfunction is selected, then nothing to do.
- * This is possible during init and we do not
- * want to change the reset values set by the HW
- */
- return;
- }
-
- switch (altfunc) {
- case GPIO_MAIN_FUNC:
- insel = &scc_regs->iomux_main_insel;
- outsel = &scc_regs->iomux_main_outsel;
- oensel = &scc_regs->iomux_main_oensel;
- altfunc_to_clear = GPIO_MAIN_FUNC_NEG_MASK;
- break;
-
- case GPIO_ALTFUNC_1:
- insel = &scc_regs->iomux_altf1_insel;
- outsel = &scc_regs->iomux_altf1_outsel;
- oensel = &scc_regs->iomux_altf1_oensel;
- altfunc_to_clear = GPIO_ALTFUNC_1_NEG_MASK;
- break;
-
- case GPIO_ALTFUNC_2:
- insel = &scc_regs->iomux_altf2_insel;
- outsel = &scc_regs->iomux_altf2_outsel;
- oensel = &scc_regs->iomux_altf2_oensel;
- altfunc_to_clear = GPIO_ALTFUNC_2_NEG_MASK;
- break;
-
- case GPIO_ALTFUNC_3:
- insel = &scc_regs->iomux_altf3_insel;
- outsel = &scc_regs->iomux_altf3_outsel;
- oensel = &scc_regs->iomux_altf3_oensel;
- altfunc_to_clear = GPIO_ALTFUNC_3_NEG_MASK;
- break;
- default:
- break;
- }
-
- /* Select the wanted function's output enable bit first.
- * This way the output won't be disabled which is desired
- * if we switch from output to output function
- */
- *oensel |= pin_mask;
-
- /* Clear all alternate function registers which are not selected */
- scc_clear_alt_func(scc_regs, altfunc_to_clear, pin_mask);
-
- /* Enable input and output data line */
- *insel |= pin_mask;
- *outsel |= pin_mask;
-}
-
-void musca_a1_scc_set_pinmode(struct musca_a1_scc_dev_t* dev, uint32_t pin_mask,
- enum pinmode_select_t mode)
-{
- struct musca_a1_scc_reg_map_t* scc_regs =
- (struct musca_a1_scc_reg_map_t*) dev->cfg->base;
-
- switch (mode) {
- case PINMODE_NONE:
- scc_regs->iopad_pe &= ~pin_mask;
- break;
- case PINMODE_PULL_DOWN:
- /* If the pull select bit is set to 0 it means pull down */
- scc_regs->iopad_ps &= ~pin_mask;
- scc_regs->iopad_pe |= pin_mask;
- break;
- case PINMODE_PULL_UP:
- /* If the pull select bit is set to 1 it means pull up */
- scc_regs->iopad_ps |= pin_mask;
- scc_regs->iopad_pe |= pin_mask;
- break;
- default:
- break;
- }
-}
-
-void musca_a1_scc_set_default_in(struct musca_a1_scc_dev_t* dev,
- enum gpio_altfunc_t altfunc,
- uint32_t default_in_mask,
- uint32_t default_in_value)
-{
- struct musca_a1_scc_reg_map_t* scc_regs =
- (struct musca_a1_scc_reg_map_t*) dev->cfg->base;
- uint32_t iomux_value = 0;
-
- if (altfunc >= GPIO_ALTFUNC_MAX) {
- /* If no altfunction is selected, then nothing to do */
- return;
- }
-
- switch (altfunc) {
- case GPIO_MAIN_FUNC:
- iomux_value = scc_regs->iomux_main_default_in & ~default_in_mask;
- iomux_value |= (default_in_value & default_in_mask);
- scc_regs->iomux_main_default_in = iomux_value;
- scc_regs->iomux_main_insel = (scc_regs->iomux_main_insel & ~default_in_mask);
- break;
-
- case GPIO_ALTFUNC_1:
- iomux_value = scc_regs->iomux_altf1_default_in & ~default_in_mask;
- iomux_value |= (default_in_value & default_in_mask);
- scc_regs->iomux_altf1_default_in = iomux_value;
- scc_regs->iomux_altf1_insel = (scc_regs->iomux_altf1_insel & ~default_in_mask);
- break;
-
- case GPIO_ALTFUNC_2:
- iomux_value = scc_regs->iomux_altf2_default_in & ~default_in_mask;
- iomux_value |= (default_in_value & default_in_mask);
- scc_regs->iomux_altf2_default_in = iomux_value;
- scc_regs->iomux_altf2_insel = (scc_regs->iomux_altf2_insel & ~default_in_mask);
- break;
-
- case GPIO_ALTFUNC_3:
- iomux_value = scc_regs->iomux_altf3_default_in & ~default_in_mask;
- iomux_value |= (default_in_value & default_in_mask);
- scc_regs->iomux_altf3_default_in = iomux_value;
- scc_regs->iomux_altf3_insel = (scc_regs->iomux_altf3_insel & ~default_in_mask);
- break;
- default:
- break;
- }
-}
diff --git a/platform/ext/target/musca_a/Native_Driver/musca_a1_scc_drv.h b/platform/ext/target/musca_a/Native_Driver/musca_a1_scc_drv.h
deleted file mode 100644
index d4b4f1d..0000000
--- a/platform/ext/target/musca_a/Native_Driver/musca_a1_scc_drv.h
+++ /dev/null
@@ -1,109 +0,0 @@
-/*
- * Copyright (c) 2017-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-#ifndef __MUSCA_A1_SCC_DRV_H__
-#define __MUSCA_A1_SCC_DRV_H__
-
-#include <stdint.h>
-#include <stddef.h>
-
-/**
- * \brief Enum to store alternate function values.
- * They are used as shift operand, must be unsigned.
- */
-enum gpio_altfunc_t {
- GPIO_MAIN_FUNC = 0UL,
- GPIO_ALTFUNC_1,
- GPIO_ALTFUNC_2,
- GPIO_ALTFUNC_3,
- GPIO_ALTFUNC_MAX
-};
-
-#define GPIO_ALTFUNC_ALL_MASK ((1U << GPIO_ALTFUNC_MAX) - 1)
-
-/**
-* \brief Enum to store alternate function mask values.
-*/
-enum gpio_altfunc_mask_t {
- GPIO_ALTFUNC_NONE = 0,
- GPIO_MAIN_FUNC_MASK = (1UL << GPIO_MAIN_FUNC),
- GPIO_ALTFUNC_1_MASK = (1UL << GPIO_ALTFUNC_1),
- GPIO_ALTFUNC_2_MASK = (1UL << GPIO_ALTFUNC_2),
- GPIO_ALTFUNC_3_MASK = (1UL << GPIO_ALTFUNC_3),
- GPIO_MAIN_FUNC_NEG_MASK = (~GPIO_MAIN_FUNC_MASK & GPIO_ALTFUNC_ALL_MASK),
- GPIO_ALTFUNC_1_NEG_MASK = (~GPIO_ALTFUNC_1_MASK & GPIO_ALTFUNC_ALL_MASK),
- GPIO_ALTFUNC_2_NEG_MASK = (~GPIO_ALTFUNC_2_MASK & GPIO_ALTFUNC_ALL_MASK),
- GPIO_ALTFUNC_3_NEG_MASK = (~GPIO_ALTFUNC_3_MASK & GPIO_ALTFUNC_ALL_MASK)
-};
-
-enum pinmode_select_t {
- PINMODE_NONE,
- PINMODE_PULL_DOWN,
- PINMODE_PULL_UP
-};
-
-/* MUSCA SCC device configuration structure */
-struct musca_a1_scc_dev_cfg_t {
- const uint32_t base; /*!< SCC base address */
-};
-
-/* MUSCA SCC device structure */
-struct musca_a1_scc_dev_t {
- const struct musca_a1_scc_dev_cfg_t* const cfg; /*!< SCC configuration */
-};
-
-/**
- * \brief Sets selected alternate functions for selected pins
- *
- * \param[in] dev SCC device pointer \ref musca_a1_scc_dev_t
- * \param[in] altfunc Alternate function to set \ref gpio_altfunc_t
- * \param[in] pin_mask Pin mask for the alternate functions
- *
- * \note This function doesn't check if scc dev is NULL.
- * \note If no alternate function is selected then the function won't do anything
- */
-void musca_a1_scc_set_alt_func(struct musca_a1_scc_dev_t* dev,
- enum gpio_altfunc_t altfunc, uint32_t pin_mask);
-
-/**
- * \brief Sets pinmode for the given pins
- *
- * \param[in] dev SCC device pointer \ref musca_a1_scc_dev_t
- * \param[in] pin_mask Pin mask for the alternate functions
- * \param[in] mode Pin mode to set \ref pinmode_select_t
- *
- * \note This function doesn't check if scc dev is NULL.
- */
-void musca_a1_scc_set_pinmode(struct musca_a1_scc_dev_t* dev, uint32_t pin_mask,
- enum pinmode_select_t mode);
-
-/**
- * \brief Sets default input values for the selected pins
- *
- * \param[in] dev SCC device pointer \ref musca_a1_scc_dev_t
- * \param[in] altfunc The selected alternate function that is set the
- * specified default in value \ref gpio_altfunc_t
- * \param[in] default_in_mask Pin mask for selecting pins
- * \param[in] default_in_value Pin values for the selected pins
- *
- * \note This function doesn't check if scc_base is NULL.
- * \note If no alternate function is selected, the function won't do anything
- */
-void musca_a1_scc_set_default_in(struct musca_a1_scc_dev_t* dev,
- enum gpio_altfunc_t altfunc,
- uint32_t default_in_mask,
- uint32_t default_in_value);
-
-#endif /* __MUSCA_A1_SCC_DRV_H__ */
diff --git a/platform/ext/target/musca_a/Native_Driver/ppc_sse200_drv.c b/platform/ext/target/musca_a/Native_Driver/ppc_sse200_drv.c
deleted file mode 100644
index 40cf650..0000000
--- a/platform/ext/target/musca_a/Native_Driver/ppc_sse200_drv.c
+++ /dev/null
@@ -1,323 +0,0 @@
-/*
- * Copyright (c) 2017-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include "ppc_sse200_drv.h"
-
-/* SPCTRL PPCs control memory mapped registers access structure */
-struct arm_spctrl_ppc_sse200_t {
- volatile uint32_t reserved[8];
- volatile uint32_t secppcintstat; /* Secure PPC Interrupt Status */
- volatile uint32_t secppcintclr; /* Secure PPC Interrupt Clear */
- volatile uint32_t secppcinten; /* Secure PPC Interrupt Enable */
- volatile uint32_t reserved1[9];
- volatile uint32_t ahbnsppc0; /* Non-Secure Access AHB slave Peripheral
- Protection Control #0 */
- volatile uint32_t reserved2[3]; /* Reserved for Future Non-secure Access
- AHB Slave Peripheral Protection
- Control */
- volatile uint32_t ahbnsppcexp0; /* Expansion 0 Non_Secure Access AHB
- slave Peripheral Protection Control */
- volatile uint32_t ahbnsppcexp1; /* Expansion 1 Non_Secure Access AHB
- slave Peripheral Protection Control */
- volatile uint32_t ahbnsppcexp2; /* Expansion 2 Non_Secure Access AHB
- slave Peripheral Protection Control */
- volatile uint32_t ahbnsppcexp3; /* Expansion 3 Non_Secure Access AHB
- slave Peripheral Protection Control */
- volatile uint32_t apbnsppc0; /* Non-Secure Access APB slave Peripheral
- Protection Control 0 */
- volatile uint32_t apbnsppc1; /* Non-Secure Access APB slave Peripheral
- Protection Control 1 */
- volatile uint32_t reserved3[2]; /* Non-Secure Access APB slave Peripheral
- Protection Control [3:1] */
- volatile uint32_t apbnsppcexp0; /* Expansion 0 Non_Secure Access APB
- slave Peripheral Protection Control */
- volatile uint32_t apbnsppcexp1; /* Expansion 1 Non_Secure Access APB
- slave Peripheral Protection Control */
- volatile uint32_t apbnsppcexp2; /* Expansion 2 Non_Secure Access APB
- slave Peripheral Protection Control */
- volatile uint32_t apbnsppcexp3; /* Expansion 3 Non_Secure Access APB
- slave Peripheral Protection Control */
- volatile uint32_t ahbspppc0; /* Secure Unprivileged Access AHB slave
- Peripheral Protection Control 0 */
- volatile uint32_t reserved4[3]; /* Reserved for Future Secure Unprivileged
- Access AHB slave Peripheral Protection
- Control */
- volatile uint32_t ahbspppcexp0; /* Expansion 0 Secure Unprivileged Access
- AHB slave Peripheral Protection
- Control */
- volatile uint32_t ahbspppcexp1; /* Expansion 1 Secure Unprivileged Access
- AHB slave Peripheral Protection
- Control */
- volatile uint32_t ahbspppcexp2; /* Expansion 2 Secure Unprivileged Access
- AHB slave Peripheral Protection
- Control */
- volatile uint32_t ahbspppcexp3; /* Expansion 3 Secure Unprivileged Access
- AHB slave Peripheral Protection
- Control */
- volatile uint32_t apbspppc0; /* Secure Unprivileged Access APB slave
- Peripheral 0 */
- volatile uint32_t apbspppc1; /* Secure Unprivileged Access APB slave
- Peripheral 1 */
- volatile uint32_t reserved5[2]; /* Reserved for Future Secure Unprivileged
- Access APB slave Peripheral Protection
- Control */
- volatile uint32_t apbspppcexp0; /* Expansion 0 Secure Unprivileged Access
- APB slave Peripheral Protection
- Control */
- volatile uint32_t apbspppcexp1; /* Expansion 1 Secure Unprivileged Access
- APB slave Peripheral Protection
- Control */
- volatile uint32_t apbspppcexp2; /* Expansion 2 Secure Unprivileged Access
- APB slave Peripheral Protection
- Control */
- volatile uint32_t apbspppcexp3; /* Expansion 3 Secure Unprivileged Access
- APB slave Peripheral Protection
- Control */
-};
-
-/* NSPCTRL PPCs memory mapped register access structure */
-struct arm_nspctrl_ppc_sse200_t {
- volatile uint32_t reserved[36];
- volatile uint32_t ahbnspppc0;
- volatile uint32_t reserved1[3];
- volatile uint32_t ahbnspppcexp0;
- volatile uint32_t ahbnspppcexp1;
- volatile uint32_t ahbnspppcexp2;
- volatile uint32_t ahbnspppcexp3;
- volatile uint32_t apbnspppc0;
- volatile uint32_t apbnspppc1;
- volatile uint32_t reserved2[2];
- volatile uint32_t apbnspppcexp0;
- volatile uint32_t apbnspppcexp1;
- volatile uint32_t apbnspppcexp2;
- volatile uint32_t apbnspppcexp3;
-};
-
-/* PPC interrupt position mask */
-#define APB_PPC0_INT_POS_MASK (1UL << 0)
-#define APB_PPC1_INT_POS_MASK (1UL << 1)
-/* Reseved bits 2:3 */
-#define APB_PPCEXP0_INT_POS_MASK (1UL << 4)
-#define APB_PPCEXP1_INT_POS_MASK (1UL << 5)
-#define APB_PPCEXP2_INT_POS_MASK (1UL << 6)
-#define APB_PPCEXP3_INT_POS_MASK (1UL << 7)
-/* Reseved bits 8:15 */
-#define AHB_PPC0_INT_POS_MASK (1UL << 16)
-/* Reseved bits 17:19 */
-#define AHB_PPCEXP0_INT_POS_MASK (1UL << 20)
-#define AHB_PPCEXP1_INT_POS_MASK (1UL << 21)
-#define AHB_PPCEXP2_INT_POS_MASK (1UL << 22)
-#define AHB_PPCEXP3_INT_POS_MASK (1UL << 23)
-/* Reseved bits 24:31 */
-
-/* ARM PPC state definitions */
-#define PPC_SSE200_INITIALIZED (1 << 0)
-
-/* Default peripheral states */
-#define SECURE_AS_DEFAULT_PERIPHERAL_STATE 1
-#define PRIVILEGE_ONLY_AS_DEFAULT_PERIPHERAL_STATE 1
-
-void ppc_sse200_init(struct ppc_sse200_dev_t* dev,
- enum ppc_sse200_name_t ppc_name)
-{
- struct arm_spctrl_ppc_sse200_t* p_spctrl =
- (struct arm_spctrl_ppc_sse200_t*)dev->cfg->spctrl_base;
- struct arm_nspctrl_ppc_sse200_t* p_nspctrl =
- (struct arm_nspctrl_ppc_sse200_t*)dev->cfg->nspctrl_base;
-
- switch(ppc_name) {
- case AHB_PPC0:
- dev->data->p_ns_ppc = &p_spctrl->ahbnsppc0;
- dev->data->p_sp_ppc = &p_spctrl->ahbspppc0;
- dev->data->p_nsp_ppc = &p_nspctrl->ahbnspppc0;
- dev->data->int_bit_mask = AHB_PPC0_INT_POS_MASK;
- break;
- case AHB_PPC_EXP0:
- dev->data->p_ns_ppc = &p_spctrl->ahbnsppcexp0;
- dev->data->p_sp_ppc = &p_spctrl->ahbspppcexp0;
- dev->data->p_nsp_ppc = &p_nspctrl->ahbnspppcexp0;
- dev->data->int_bit_mask = AHB_PPCEXP0_INT_POS_MASK;
- break;
- case AHB_PPC_EXP1:
- dev->data->p_ns_ppc = &p_spctrl->ahbnsppcexp1;
- dev->data->p_sp_ppc = &p_spctrl->ahbspppcexp1;
- dev->data->p_nsp_ppc = &p_nspctrl->ahbnspppcexp1;
- dev->data->int_bit_mask = AHB_PPCEXP1_INT_POS_MASK;
- break;
- case AHB_PPC_EXP2:
- dev->data->p_ns_ppc = &p_spctrl->ahbnsppcexp2;
- dev->data->p_sp_ppc = &p_spctrl->ahbspppcexp2;
- dev->data->p_nsp_ppc = &p_nspctrl->ahbnspppcexp2;
- dev->data->int_bit_mask = AHB_PPCEXP2_INT_POS_MASK;
- break;
- case AHB_PPC_EXP3:
- dev->data->p_ns_ppc = &p_spctrl->ahbnsppcexp3;
- dev->data->p_sp_ppc = &p_spctrl->ahbspppcexp3;
- dev->data->p_nsp_ppc = &p_nspctrl->ahbnspppcexp3;
- dev->data->int_bit_mask = AHB_PPCEXP3_INT_POS_MASK;
- break;
- case APB_PPC0:
- dev->data->p_ns_ppc = &p_spctrl->apbnsppc0;
- dev->data->p_sp_ppc = &p_spctrl->apbspppc0;
- dev->data->p_nsp_ppc = &p_nspctrl->apbnspppc0;
- dev->data->int_bit_mask = APB_PPC0_INT_POS_MASK;
- break;
- case APB_PPC1:
- dev->data->p_ns_ppc = &p_spctrl->apbnsppc1;
- dev->data->p_sp_ppc = &p_spctrl->apbspppc1;
- dev->data->p_nsp_ppc = &p_nspctrl->apbnspppc1;
- dev->data->int_bit_mask = APB_PPC1_INT_POS_MASK;
- break;
- case APB_PPC_EXP0:
- dev->data->p_ns_ppc = &p_spctrl->apbnsppcexp0;
- dev->data->p_sp_ppc = &p_spctrl->apbspppcexp0;
- dev->data->p_nsp_ppc = &p_nspctrl->apbnspppcexp0;
- dev->data->int_bit_mask = APB_PPCEXP0_INT_POS_MASK;
- break;
- case APB_PPC_EXP1:
- dev->data->p_ns_ppc = &p_spctrl->apbnsppcexp1;
- dev->data->p_sp_ppc = &p_spctrl->apbspppcexp1;
- dev->data->p_nsp_ppc = &p_nspctrl->apbnspppcexp1;
- dev->data->int_bit_mask = APB_PPCEXP1_INT_POS_MASK;
- break;
- case APB_PPC_EXP2:
- dev->data->p_ns_ppc = &p_spctrl->apbnsppcexp2;
- dev->data->p_sp_ppc = &p_spctrl->apbspppcexp2;
- dev->data->p_nsp_ppc = &p_nspctrl->apbnspppcexp2;
- dev->data->int_bit_mask = APB_PPCEXP2_INT_POS_MASK;
- break;
- case APB_PPC_EXP3:
- dev->data->p_ns_ppc = &p_spctrl->apbnsppcexp3;
- dev->data->p_sp_ppc = &p_spctrl->apbspppcexp3;
- dev->data->p_nsp_ppc = &p_nspctrl->apbnspppcexp3;
- dev->data->int_bit_mask = APB_PPCEXP3_INT_POS_MASK;
- break;
- /* default: The default is not defined intentionally to force the
- * compiler to check that all enumeration values are
- * covered in the switch.*/
- }
-
- dev->data->state = PPC_SSE200_INITIALIZED;
-}
-
-enum ppc_sse200_error_t ppc_sse200_config_peripheral(
- struct ppc_sse200_dev_t* dev,
- uint8_t periph,
- enum ppc_sse200_sec_attr_t sec_attr,
- enum ppc_sse200_priv_attr_t priv_attr)
-{
- if(dev->data->state != PPC_SSE200_INITIALIZED) {
- return PPC_SSE200_NOT_INIT;
- }
-
- if(sec_attr == PPC_SSE200_SECURE_ONLY) {
- /* Sets secure attribute */
- *(dev->data->p_ns_ppc) &= ~(1U << periph);
-
- /* Uses secure unprivileged access address (SPCTRL) to set privilege
- * attribute */
- if(priv_attr == PPC_SSE200_PRIV_ONLY) {
- *(dev->data->p_sp_ppc) &= ~(1U << periph);
- } else {
- *(dev->data->p_sp_ppc) |= (1U << periph);
- }
- } else {
- /* Sets secure attribute */
- *(dev->data->p_ns_ppc) |= (1U << periph);
-
- /* Uses non-secure unprivileged access address (NSPCTRL) to set
- * privilege attribute */
- if(priv_attr == PPC_SSE200_PRIV_ONLY) {
- *(dev->data->p_nsp_ppc) &= ~(1U << periph);
- } else {
- *(dev->data->p_nsp_ppc) |= (1U << periph);
- }
- }
-
- return PPC_SSE200_ERR_NONE;
-}
-
-uint32_t ppc_sse200_is_periph_secure(struct ppc_sse200_dev_t* dev,
- uint8_t periph)
-{
- if(dev->data->state != PPC_SSE200_INITIALIZED) {
- return SECURE_AS_DEFAULT_PERIPHERAL_STATE;
- }
-
- return ((*(dev->data->p_ns_ppc) & (1U << periph)) == 0);
-}
-
-uint32_t ppc_sse200_is_periph_priv_only(struct ppc_sse200_dev_t* dev,
- uint8_t periph)
-{
- if(dev->data->state != PPC_SSE200_INITIALIZED) {
- return PRIVILEGE_ONLY_AS_DEFAULT_PERIPHERAL_STATE;
- }
-
- if ((*(dev->data->p_ns_ppc) & (1U << periph)) == 0) {
- /* Returns secure unprivileged access address (SPCTRL) */
- return ((*(dev->data->p_sp_ppc) & (1U << periph)) == 0);
- } else {
- /* Returns non-secure unprivileged access address (NSPCTRL) */
- return ((*(dev->data->p_nsp_ppc) & (1U << periph)) == 0);
- }
-}
-
-enum ppc_sse200_error_t ppc_sse200_irq_enable(struct ppc_sse200_dev_t* dev)
-{
- struct arm_spctrl_ppc_sse200_t* p_spctrl =
- (struct arm_spctrl_ppc_sse200_t*)dev->cfg->spctrl_base;
-
- if(dev->data->state != PPC_SSE200_INITIALIZED) {
- return PPC_SSE200_NOT_INIT;
- }
-
- p_spctrl->secppcinten |= dev->data->int_bit_mask;
-
- return PPC_SSE200_ERR_NONE;
-}
-
-void ppc_sse200_irq_disable(struct ppc_sse200_dev_t* dev)
-{
- struct arm_spctrl_ppc_sse200_t* p_spctrl =
- (struct arm_spctrl_ppc_sse200_t*)dev->cfg->spctrl_base;
-
- if(dev->data->state == PPC_SSE200_INITIALIZED) {
- p_spctrl->secppcinten &= ~(dev->data->int_bit_mask);
- }
-}
-
-void ppc_sse200_clear_irq(struct ppc_sse200_dev_t* dev)
-{
- struct arm_spctrl_ppc_sse200_t* p_spctrl =
- (struct arm_spctrl_ppc_sse200_t*)dev->cfg->spctrl_base;
-
- if(dev->data->state == PPC_SSE200_INITIALIZED) {
- p_spctrl->secppcintclr = dev->data->int_bit_mask;
- }
-}
-
-uint32_t ppc_sse200_irq_state(struct ppc_sse200_dev_t* dev)
-{
- struct arm_spctrl_ppc_sse200_t* p_spctrl =
- (struct arm_spctrl_ppc_sse200_t*)dev->cfg->spctrl_base;
-
- if(dev->data->state != PPC_SSE200_INITIALIZED) {
- return 0;
- }
-
- return ((p_spctrl->secppcintstat & dev->data->int_bit_mask) != 0);
-}
diff --git a/platform/ext/target/musca_a/Native_Driver/ppc_sse200_drv.h b/platform/ext/target/musca_a/Native_Driver/ppc_sse200_drv.h
deleted file mode 100644
index b6ce8c2..0000000
--- a/platform/ext/target/musca_a/Native_Driver/ppc_sse200_drv.h
+++ /dev/null
@@ -1,198 +0,0 @@
-/*
- * Copyright (c) 2017-2019 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file ppc_sse200_drv.h
- * \brief Generic driver for ARM SEE 200 Peripheral Protection
- * Controllers (PPC).
- */
-
-#ifndef __PPC_SSE_200_DRV_H__
-#define __PPC_SSE_200_DRV_H__
-
-#include <stdint.h>
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/* Secure Privilege Control Block aka SPCTRL */
-/* Non-Secure Privilege Control Block aka NSPCTRL */
-
-/* ARM TrustZone PPC device configuration structure */
-struct ppc_sse200_dev_cfg_t {
- uint32_t const spctrl_base; /*!< SPCTRL base address */
- uint32_t const nspctrl_base; /*!< NSPCTRL base address */
-};
-
-/* ARM TrustZone PPC device data structure */
-struct ppc_sse200_dev_data_t {
- volatile uint32_t* p_ns_ppc; /*!< Pointer to non-secure register */
- volatile uint32_t* p_sp_ppc; /*!< Pointer to secure unprivileged
- register */
- volatile uint32_t* p_nsp_ppc; /*!< Pointer to non-secure unprivileged
- register */
- uint32_t int_bit_mask; /*!< Interrupt bit mask */
- uint8_t state; /*!< Indicates if the PPC driver
- is initialized */
- uint8_t reserved[3]; /*!< 32 bits alignment */
-};
-
-/* ARM PPC device structure */
-struct ppc_sse200_dev_t {
- const struct ppc_sse200_dev_cfg_t* const cfg; /*!< PPC configuration */
- struct ppc_sse200_dev_data_t* const data; /*!< PPC data */
-};
-
-/* Security attribute used to configure the peripheral */
-enum ppc_sse200_sec_attr_t {
- PPC_SSE200_SECURE_ONLY, /*! Secure access */
- PPC_SSE200_NONSECURE_ONLY, /*! Non-secure access */
-};
-
-/* Privilege attribute used to configure the peripheral */
-enum ppc_sse200_priv_attr_t {
- PPC_SSE200_PRIV_AND_NONPRIV, /*! Privilege and non-Privilege access */
- PPC_SSE200_PRIV_ONLY, /*! Privilege only access */
-};
-
-/* ARM PPC error codes */
-enum ppc_sse200_error_t {
- PPC_SSE200_ERR_NONE = 0, /*!< No error */
- PPC_SSE200_NOT_INIT, /*!< PPC not initialized */
-};
-
-/* ARM PPC names */
-enum ppc_sse200_name_t {
- AHB_PPC0 = 0, /*!< AHB PPC0 */
- AHB_PPC_EXP0, /*!< Expansion 0 AHB PPC */
- AHB_PPC_EXP1, /*!< Expansion 1 AHB PPC */
- AHB_PPC_EXP2, /*!< Expansion 2 AHB PPC */
- AHB_PPC_EXP3, /*!< Expansion 3 AHB PPC */
- APB_PPC0, /*!< APB PPC0 */
- APB_PPC1, /*!< APB PPC1 */
- APB_PPC_EXP0, /*!< Expansion 0 APB PPC */
- APB_PPC_EXP1, /*!< Expansion 1 APB PPC */
- APB_PPC_EXP2, /*!< Expansion 2 APB PPC */
- APB_PPC_EXP3 /*!< Expansion 3 APB PPC */
-};
-
-/**
- * \brief Initialize the PPC device.
- *
- * \param[in] dev PPC device \ref ppc_sse200_dev_t
- * \param[in] ppc_name PPC name \ref ppc_sse200_name_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void ppc_sse200_init(struct ppc_sse200_dev_t* dev,
- enum ppc_sse200_name_t ppc_name);
-
-/**
- * \brief Configures the PPC device.
- *
- * \param[in] dev PPC device \ref ppc_sse200_dev_t
- * \param[in] periph Peripheral position in the PPC.
- * \param[in] sec_attr Secure attribute value.
- * \param[in] priv_attr Privilege attribute value.
- *
- * \return Returns error code as specified in \ref ppc_sse200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum ppc_sse200_error_t ppc_sse200_config_peripheral(
- struct ppc_sse200_dev_t* dev,
- uint8_t periph,
- enum ppc_sse200_sec_attr_t sec_attr,
- enum ppc_sse200_priv_attr_t priv_attr);
-/**
- * \brief Checks if the peripheral is configured as secure or non-secure.
- *
- * \param[in] dev PPC device \ref ppc_sse200_dev_t
- * \param[in] periph Peripheral position in the PPC.
- *
- * \return Returns 1 for secure and 0 for non-secure.
- * If the driver is not initalized the return value is 1 (secure) as
- * it is the default system configuration.
- *
- * \note This function doesn't check if dev is NULL.
- */
-uint32_t ppc_sse200_is_periph_secure(struct ppc_sse200_dev_t* dev,
- uint8_t periph);
-
-/**
- * \brief Checks if the peripheral is configured as Privilege only or
- * Privilege and non-Privilege access mode.
- *
- * \param[in] dev PPC device \ref ppc_sse200_dev_t
- * \param[in] periph Peripheral position in the PPC.
- *
- * \return Returns 1 for Privilege only configuration and 0 for Privilege and
- * non-Privilege access.
- * If the driver is not initalized the return of this function is
- * 1 (Privilege only) as it is the default system configuration.
- *
- * \note This function doesn't check if dev is NULL.
- */
-uint32_t ppc_sse200_is_periph_priv_only(struct ppc_sse200_dev_t* dev,
- uint8_t periph);
-/**
- * \brief Enables PPC interrupt.
- *
- * \param[in] dev PPC device \ref ppc_sse200_dev_t
- *
- * \return Returns error code as specified in \ref ppc_sse200_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum ppc_sse200_error_t ppc_sse200_irq_enable(struct ppc_sse200_dev_t* dev);
-
-/**
- * \brief Disables PPC interrupt.
- *
- * \param[in] dev PPC device \ref ppc_sse200_dev_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void ppc_sse200_irq_disable(struct ppc_sse200_dev_t* dev);
-
-/**
- * \brief Clears PPC interrupt.
- *
- * \param[in] dev PPC device \ref ppc_sse200_dev_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void ppc_sse200_clear_irq(struct ppc_sse200_dev_t* dev);
-
-/**
- * \brief Returns the PPC interrupt state.
- *
- * \param[in] dev PPC device \ref ppc_sse200_dev_t
- *
- * \return Returns 1 if the interrupt is active and otherwise 0.
- * If the driver is not initalized the return of this function is
- * 0 (not active) as it is the default system configuration.
- *
- * \note This function doesn't check if dev is NULL.
- */
-uint32_t ppc_sse200_irq_state(struct ppc_sse200_dev_t* dev);
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __PPC_SSE_200_DRV_H__ */
diff --git a/platform/ext/target/musca_a/Native_Driver/qspi_ip6514e_drv.c b/platform/ext/target/musca_a/Native_Driver/qspi_ip6514e_drv.c
deleted file mode 100644
index bb13a42..0000000
--- a/platform/ext/target/musca_a/Native_Driver/qspi_ip6514e_drv.c
+++ /dev/null
@@ -1,755 +0,0 @@
-/*
- * Copyright (c) 2018-2019 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include <stdint.h>
-#include <stdlib.h>
-#include <stdbool.h>
-/* Use memcpy */
-#include <string.h>
-
-#include "qspi_ip6514e_drv.h"
-
-/** Setter bit manipulation macro */
-#define SET_BIT(WORD, BIT_INDEX) ((WORD) |= (1U << (BIT_INDEX)))
-/** Clearing bit manipulation macro */
-#define CLR_BIT(WORD, BIT_INDEX) ((WORD) &= ~(1U << (BIT_INDEX)))
-/** Getter bit manipulation macro */
-#define GET_BIT(WORD, BIT_INDEX) (bool)(((WORD) & (1U << (BIT_INDEX))))
-
-#define WORD_ALIGN_4B_MASK 0x3U /* Mask the first 2 bits */
-#define IS_ADDR_ALIGNED(ADDR) (((uint32_t)(ADDR) & (WORD_ALIGN_4B_MASK)) == 0U)
-
-#define BITS_PER_BYTE 8U
-#define BITS_PER_WORD 32U
-
-#define CFG_READS true
-#define CFG_WRITES false
-
-#define ARG_NOT_USED 0
-#define ARG_PTR_NOT_USED NULL
-
-#define DATA_REG_NUMBER 2U
-#define DATA_REG_LOWER 0U
-#define DATA_REG_UPPER 1U
-
-#define ERROR_VALUE 0xFFFFFFFFU
-
-/**
- * \brief QSPI IP6514E register map structure
- */
-struct _qspi_ip6514e_reg_map_t {
- volatile uint32_t qspi_cfg; /*!< 0x00 (R/W) */
- volatile uint32_t device_read_inst; /*!< 0x04 (R/W) */
- volatile uint32_t device_write_inst; /*!< 0x08 (R/W) */
- volatile uint32_t hidden1[2];
- volatile uint32_t device_size; /*!< 0x14 (R/W) */
- volatile uint32_t hidden2[3];
- volatile uint32_t remap_addr; /*!< 0x24 (R/W) */
- volatile uint32_t hidden3[26];
- volatile uint32_t flash_cmd_ctrl; /*!< 0x90 (R/W) */
- volatile uint32_t flash_cmd_addr; /*!< 0x94 (R/W) */
- volatile uint32_t hidden4[2];
- volatile uint32_t flash_cmd_read_data_lower; /*!< 0xA0 (R/ ) */
- volatile uint32_t flash_cmd_read_data_upper; /*!< 0xA4 (R/ ) */
- volatile uint32_t flash_cmd_write_data_lower; /*!< 0xA8 (R/W) */
- volatile uint32_t flash_cmd_write_data_upper; /*!< 0xAC (R/W) */
- volatile uint32_t hidden5[2];
-};
-
-/** QSPI Configuration register description (offset 0x00) */
-#define QSPI_CFG_ENABLE_POS 0U
-#define QSPI_CFG_ENABLE_ADDR_REMAP_POS 16U
-#define QSPI_CFG_BAUD_DIV_POS 19U
- #define QSPI_CFG_BAUD_DIV_MIN 2U
- #define QSPI_CFG_BAUD_DIV_MAX 32U
- #define QSPI_CFG_BAUD_DIV_BITS 4U
-#define QSPI_CFG_IDLE_POS 31U
-
-/**
- * Device Read/Write Instruction registers description (offset 0x04 and 0x08).
- * These values are the same for the Device Read Instruction register at offset
- * 0x04 and the Device Write Instruction register at offset 0x08.
- */
-#define DEVICE_READ_WRITE_INST_OPCODE_POS 0U
-#define DEVICE_READ_INST_INST_TYPE_POS 8U /* Only applies to the Read
- * register. */
-#define DEVICE_READ_WRITE_INST_ADDR_TYPE_POS 12U
-#define DEVICE_READ_WRITE_INST_DATA_TYPE_POS 16U
- #define DEVICE_READ_WRITE_INST_MODE_QSPI 2U
- #define DEVICE_READ_WRITE_INST_MODE_DSPI 1U
- #define DEVICE_READ_WRITE_INST_MODE_SPI 0U
- #define DEVICE_READ_WRITE_INST_MODE_BITS 2U
-#define DEVICE_READ_WRITE_INST_DUMMY_CYCLES_POS 24U
- #define DEVICE_READ_WRITE_INST_DUMMY_CYCLES_BITS 5U
- #define DEVICE_READ_WRITE_INST_DUMMY_CYCLES_MAX 31U
-
-/** Device Size Configuration register description (offset 0x14) */
-#define DEVICE_SIZE_ADDR_BYTES_POS 0U
- #define DEVICE_SIZE_ADDR_BYTES_MIN 1U
- #define DEVICE_SIZE_ADDR_BYTES_MAX 16U
- #define DEVICE_SIZE_ADDR_BYTES_BITS 4U
-#define DEVICE_SIZE_PAGE_BYTES_POS 4U
- #define DEVICE_SIZE_PAGE_BYTES_MAX 4095U
- #define DEVICE_SIZE_PAGE_BYTES_BITS 12U
-
-/** Flash Command Control register description (offset 0x90) */
-#define FLASH_CMD_CTRL_EXECUTE_POS 0U
-#define FLASH_CMD_CTRL_BUSY_POS 1U
-#define FLASH_CMD_CTRL_DUMMY_CYCLES_POS 7U
- #define FLASH_CMD_CTRL_DUMMY_CYCLES_MAX 31U
- #define FLASH_CMD_CTRL_DUMMY_CYCLES_BITS 5U
-#define FLASH_CMD_CTRL_WRITE_BYTES_POS 12U
- #define FLASH_CMD_CTRL_WRITE_BYTES_MAX 8U
- #define FLASH_CMD_CTRL_WRITE_BYTES_BITS 3U
-#define FLASH_CMD_CTRL_WRITE_ENABLE_POS 15U
-#define FLASH_CMD_CTRL_ADDR_BYTES_POS 16U
- #define FLASH_CMD_CTRL_ADDR_BYTES_MAX 4U
- #define FLASH_CMD_CTRL_ADDR_BYTES_BITS 2U
-#define FLASH_CMD_CTRL_ADDR_ENABLE_POS 19U
-#define FLASH_CMD_CTRL_READ_BYTES_POS 20U
- #define FLASH_CMD_CTRL_READ_BYTES_MAX 8U
- #define FLASH_CMD_CTRL_READ_BYTES_BITS 3U
-#define FLASH_CMD_CTRL_READ_ENABLE_POS 23U
-#define FLASH_CMD_CTRL_OPCODE_POS 24U
-
-/** Default register values of the QSPI Flash controller */
-#define QSPI_CFG_REG_RESET_VALUE (0x80080080U)
-#define DEVICE_READ_INSTR_REG_RESET_VALUE (0x080220EBU)
-#define DEVICE_WRITE_INSTR_REG_RESET_VALUE (0x00000002U)
-#define DEVICE_SIZE_CFG_REG_RESET_VALUE (0x00101002U)
-#define REMAP_ADDR_REG_RESET_VALUE (0x00000000U)
-#define FLASH_CMD_CONTROL_REG_RESET_VALUE (0x00000000U)
-#define FLASH_CMD_ADDRESS_REG_RESET_VALUE (0x00000000U)
-#define FLASH_CMD_WRITE_DATA_REG_RESET_VALUE (0x00000000U)
-
-/**
- * \brief Change specific bits in a 32 bits word.
- *
- * \param[in,out] word Pointer of the word to change
- * \param[in] bits bits_length bits to put at bits_pos in the word
- * pointed
- * \param[in] bits_length Number of bits to change
- * \param[in] bits_pos Position of the bits to change
- *
- * \note This function will do nothing if the parameters given are incorret:
- * * word is NULL
- * * bits_length + bits_pos > 32
- * * bits_length is 0
- */
-static void change_bits_in_word(volatile uint32_t *word,
- uint32_t bits,
- uint32_t bits_length,
- uint32_t bits_pos)
-{
- uint32_t mask;
-
- if ((word == NULL) ||
- ((bits_length + bits_pos) > BITS_PER_WORD) ||
- (bits_length == 0U)) {
- /* Silently fail */
- return;
- }
-
- /* Change all the bits */
- if (bits_length == BITS_PER_WORD) {
- *word = bits;
- return;
- }
-
- mask = ((1U << bits_length) - 1);
- /*
- * We change the bits in three steps:
- * - clear bits_length bits with zeroes at bits_pos in the word
- * - mask bits in case it contains more than bits_length bits
- * - set the new bits in the cleared word
- * Because the data pointed by word is only read once, the data will still
- * be coherent after an interruption that changes it.
- */
- *word = ((*word & ~(mask << bits_pos)) | ((bits & mask) << bits_pos));
-}
-
-/**
- * \brief Configure reads or writes commands for direct operations.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- * \param[in] opcode Read/write opcode that will be used for every
- * direct read/write
- * \param[in] dummy_cycles Number of dummy cycles to wait before triggering
- * the command, this value must be between 0 and 31
- * (both included)
- * \param[in] is_reads_cfg true to configure direct reads, false to configure
- * direct writes
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note The QSPI controller should be idle before calling this function.
- */
-static enum qspi_ip6514e_error_t qspi_ip6514e_cfg_reads_writes(
- struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- uint32_t dummy_cycles,
- bool is_reads_cfg)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
- /*
- * Select the good register address if we want to configure reads or writes.
- */
- volatile uint32_t *device_read_write_inst_reg = is_reads_cfg ?
- &(reg_map->device_read_inst) :
- &(reg_map->device_write_inst);
- uint32_t device_read_write_inst_reg_copy = *device_read_write_inst_reg;
-
- /*
- * Wait for the Serial Interface and QSPI pipeline to be IDLE when
- * all low level synchronization has been done.
- */
- while(!qspi_ip6514e_is_idle(dev));
-
- if (dummy_cycles > DEVICE_READ_WRITE_INST_DUMMY_CYCLES_MAX) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- change_bits_in_word(&device_read_write_inst_reg_copy,
- (uint32_t)opcode,
- BITS_PER_BYTE,
- DEVICE_READ_WRITE_INST_OPCODE_POS);
- change_bits_in_word(&device_read_write_inst_reg_copy,
- dummy_cycles,
- DEVICE_READ_WRITE_INST_DUMMY_CYCLES_BITS,
- DEVICE_READ_WRITE_INST_DUMMY_CYCLES_POS);
-
- *device_read_write_inst_reg = device_read_write_inst_reg_copy;
-
- return QSPI_IP6514E_ERR_NONE;
-}
-
-/**
- * \brief Given the public SPI mode enumeration, returns the private value it
- * maps to in the register field.
- *
- * \param[in] spi_mode Read/write opcode that will be used for every direct
- * read/write
- *
- * \return Return the correct DEVICE_READ_WRITE_INST_MODE value.
- */
-static uint32_t spi_mode_field_value(enum qspi_ip6514e_spi_mode_t spi_mode)
-{
- switch (spi_mode) {
- case QSPI_IP6514E_SPI_MODE:
- return DEVICE_READ_WRITE_INST_MODE_SPI;
- case QSPI_IP6514E_DSPI_MODE:
- return DEVICE_READ_WRITE_INST_MODE_DSPI;
- case QSPI_IP6514E_QSPI_MODE:
- return DEVICE_READ_WRITE_INST_MODE_QSPI;
- default:
- return ERROR_VALUE;
- }
-}
-
-bool qspi_ip6514e_is_idle(struct qspi_ip6514e_dev_t* dev)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
-
- return GET_BIT(reg_map->qspi_cfg, QSPI_CFG_IDLE_POS);
-}
-
-bool qspi_ip6514e_is_enabled(struct qspi_ip6514e_dev_t* dev)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
-
- return GET_BIT(reg_map->qspi_cfg, QSPI_CFG_ENABLE_POS);
-}
-
-void qspi_ip6514e_disable(struct qspi_ip6514e_dev_t* dev)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
-
- CLR_BIT(reg_map->qspi_cfg, QSPI_CFG_ENABLE_POS);
-}
-
-void qspi_ip6514e_enable(struct qspi_ip6514e_dev_t* dev)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
-
- SET_BIT(reg_map->qspi_cfg, QSPI_CFG_ENABLE_POS);
-}
-
-enum qspi_ip6514e_error_t qspi_ip6514e_set_baud_rate_div(
- struct qspi_ip6514e_dev_t* dev,
- uint32_t div)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
-
- /*
- * Wait for the Serial Interface and QSPI pipeline to be IDLE when
- * all low level synchronization has been done.
- */
- while(!qspi_ip6514e_is_idle(dev));
-
- /* div should be an even number. */
- if (((div & 1U) == 1) ||
- (div < QSPI_CFG_BAUD_DIV_MIN) ||
- (div > QSPI_CFG_BAUD_DIV_MAX)) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- /*
- * The div value (between 2 and 32) needs to be stored in the register on a
- * 4 bits field.
- */
- change_bits_in_word(&(reg_map->qspi_cfg),
- (div / 2) - 1,
- QSPI_CFG_BAUD_DIV_BITS,
- QSPI_CFG_BAUD_DIV_POS);
-
- return QSPI_IP6514E_ERR_NONE;
-}
-
-enum qspi_ip6514e_error_t qspi_ip6514e_set_spi_mode(
- struct qspi_ip6514e_dev_t* dev,
- enum qspi_ip6514e_spi_mode_t inst_type,
- enum qspi_ip6514e_spi_mode_t addr_type,
- enum qspi_ip6514e_spi_mode_t data_type)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
- uint32_t inst_spi_mode, addr_spi_mode, data_spi_mode;
- /*
- * A local copy of the Device Read Instruction and Device Write Instruction
- * registers is used to limit APB accesses.
- */
- uint32_t device_read_inst_cpy = reg_map->device_read_inst;
- uint32_t device_write_inst_cpy = reg_map->device_write_inst;
-
- /*
- * Wait for the Serial Interface and QSPI pipeline to be IDLE when
- * all low level synchronization has been done.
- */
- while(!qspi_ip6514e_is_idle(dev));
-
- /*
- * First check that the instruction mode is not SPI. If that is the case,
- * the address and data mode register fields become DO NOT CARE.
- */
- inst_spi_mode = spi_mode_field_value(inst_type);
- if (inst_spi_mode == ERROR_VALUE) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
- if (inst_type != QSPI_IP6514E_SPI_MODE) {
- change_bits_in_word(&(reg_map->device_read_inst),
- inst_spi_mode,
- DEVICE_READ_WRITE_INST_MODE_BITS,
- DEVICE_READ_INST_INST_TYPE_POS);
- return QSPI_IP6514E_ERR_NONE;
- }
-
- /* Now check and set address and data modes. */
- addr_spi_mode = spi_mode_field_value(addr_type);
- data_spi_mode = spi_mode_field_value(data_type);
- if ((addr_spi_mode == ERROR_VALUE) || (data_spi_mode == ERROR_VALUE)) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- /* Change the Device Read Instruction register. */
- change_bits_in_word(&device_read_inst_cpy,
- inst_spi_mode,
- DEVICE_READ_WRITE_INST_MODE_BITS,
- DEVICE_READ_INST_INST_TYPE_POS);
- change_bits_in_word(&device_read_inst_cpy,
- addr_spi_mode,
- DEVICE_READ_WRITE_INST_MODE_BITS,
- DEVICE_READ_WRITE_INST_ADDR_TYPE_POS);
- change_bits_in_word(&device_read_inst_cpy,
- data_spi_mode,
- DEVICE_READ_WRITE_INST_MODE_BITS,
- DEVICE_READ_WRITE_INST_DATA_TYPE_POS);
-
- /* Change the Device Write Instruction register. */
- change_bits_in_word(&device_write_inst_cpy,
- addr_spi_mode,
- DEVICE_READ_WRITE_INST_MODE_BITS,
- DEVICE_READ_WRITE_INST_ADDR_TYPE_POS);
- change_bits_in_word(&device_write_inst_cpy,
- data_spi_mode,
- DEVICE_READ_WRITE_INST_MODE_BITS,
- DEVICE_READ_WRITE_INST_DATA_TYPE_POS);
-
- /* Save the changes. */
- reg_map->device_read_inst = device_read_inst_cpy;
- reg_map->device_write_inst = device_write_inst_cpy;
-
- return QSPI_IP6514E_ERR_NONE;
-}
-
-enum qspi_ip6514e_error_t qspi_ip6514e_cfg_reads(struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- uint32_t dummy_cycles)
-{
- return qspi_ip6514e_cfg_reads_writes(dev, opcode, dummy_cycles, CFG_READS);
-}
-
-enum qspi_ip6514e_error_t qspi_ip6514e_cfg_writes(
- struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- uint32_t dummy_cycles)
-{
- return qspi_ip6514e_cfg_reads_writes(dev, opcode, dummy_cycles, CFG_WRITES);
-}
-
-enum qspi_ip6514e_error_t qspi_ip6514e_cfg_page_size(
- struct qspi_ip6514e_dev_t* dev,
- uint32_t page_size)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
-
- /*
- * Wait for the Serial Interface and QSPI pipeline to be IDLE when
- * all low level synchronization has been done.
- */
- while(!qspi_ip6514e_is_idle(dev));
-
- if (page_size > DEVICE_SIZE_PAGE_BYTES_MAX) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- change_bits_in_word(&(reg_map->device_size),
- page_size,
- DEVICE_SIZE_PAGE_BYTES_BITS,
- DEVICE_SIZE_PAGE_BYTES_POS);
-
- return QSPI_IP6514E_ERR_NONE;
-}
-
-enum qspi_ip6514e_error_t qspi_ip6514e_cfg_addr_bytes(
- struct qspi_ip6514e_dev_t* dev,
- uint32_t bytes_number)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
-
- /*
- * Wait for the Serial Interface and QSPI pipeline to be IDLE when
- * all low level synchronization has been done.
- */
- while(!qspi_ip6514e_is_idle(dev));
-
- if (bytes_number < DEVICE_SIZE_ADDR_BYTES_MIN ||
- bytes_number > DEVICE_SIZE_ADDR_BYTES_MAX) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- change_bits_in_word(&(reg_map->device_size),
- bytes_number - 1,
- DEVICE_SIZE_ADDR_BYTES_BITS,
- DEVICE_SIZE_ADDR_BYTES_POS);
-
-
- return QSPI_IP6514E_ERR_NONE;
-}
-
-void qspi_ip6514e_remap_addr(struct qspi_ip6514e_dev_t* dev, uint32_t offset)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
- /* Save the enable state to restore it after. */
- bool is_enabled = qspi_ip6514e_is_enabled(dev);
-
- if (is_enabled) {
- qspi_ip6514e_disable(dev);
- }
-
- reg_map->remap_addr = offset;
- SET_BIT(reg_map->qspi_cfg, QSPI_CFG_ENABLE_ADDR_REMAP_POS);
-
- if (is_enabled) {
- qspi_ip6514e_enable(dev);
- }
-}
-
-void qspi_ip6514e_disable_remap(struct qspi_ip6514e_dev_t* dev)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
- /* Save the enable state to restore it after. */
- bool is_enabled = qspi_ip6514e_is_enabled(dev);
-
- if (is_enabled) {
- qspi_ip6514e_disable(dev);
- }
-
- CLR_BIT(reg_map->qspi_cfg, QSPI_CFG_ENABLE_ADDR_REMAP_POS);
-
- if (is_enabled) {
- qspi_ip6514e_enable(dev);
- }
-}
-
-void qspi_ip6514e_reset_regs(struct qspi_ip6514e_dev_t* dev)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
-
- /* Restore the default value of the QSPI Configuration register. */
- reg_map->qspi_cfg = QSPI_CFG_REG_RESET_VALUE;
-
- /* Restore the default value of the Device R/W Instruction registers. */
- reg_map->device_read_inst = DEVICE_READ_INSTR_REG_RESET_VALUE;
- reg_map->device_write_inst = DEVICE_WRITE_INSTR_REG_RESET_VALUE;
-
- /* Restore the default value of the Device Size Configuration register. */
- reg_map->device_size = DEVICE_SIZE_CFG_REG_RESET_VALUE;
-
- /* Restore the default value of the Remap Address register. */
- reg_map->remap_addr = REMAP_ADDR_REG_RESET_VALUE;
-
- /* Restore the default value of the Flash Command Control register. */
- reg_map->flash_cmd_ctrl = FLASH_CMD_CONTROL_REG_RESET_VALUE;
- /* Restore the default value of the Flash Command Address register. */
- reg_map->flash_cmd_addr = FLASH_CMD_ADDRESS_REG_RESET_VALUE;
-
- /* Restore the default value of the Flash Command Write Data registers. */
- reg_map->flash_cmd_write_data_lower = FLASH_CMD_WRITE_DATA_REG_RESET_VALUE;
- reg_map->flash_cmd_write_data_upper = FLASH_CMD_WRITE_DATA_REG_RESET_VALUE;
-
- /*
- * This function does not affect the Flash Command Read Data registers
- * which are completely Read-Only.
- */
-}
-
-enum qspi_ip6514e_error_t qspi_ip6514e_send_cmd(struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- void *read_data,
- uint32_t read_len,
- const void *write_data,
- uint32_t write_len,
- uint32_t addr,
- uint32_t addr_bytes_number,
- uint32_t dummy_cycles)
-{
- struct _qspi_ip6514e_reg_map_t *reg_map =
- (struct _qspi_ip6514e_reg_map_t *)dev->cfg->base;
- /* To limit APB accesses, we set this reg up locally before */
- uint32_t flash_cmd_ctrl = 0U;
- bool read_requested = ((read_data != NULL) && (read_len != 0));
- bool write_requested = ((write_data != NULL) && (write_len != 0));
- bool addr_requested = (addr_bytes_number != 0);
- /*
- * To prevent unaligned and byte or halfbyte accesses to the APB registers,
- * a word aligned buffer is used to temporary transfer the data before doing
- * word accesses on these registers from that buffer.
- */
- uint32_t data_regs[DATA_REG_NUMBER] = {0};
-
- if (read_len > FLASH_CMD_CTRL_READ_BYTES_MAX) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- if (write_len > FLASH_CMD_CTRL_WRITE_BYTES_MAX) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- if (addr_bytes_number > FLASH_CMD_CTRL_ADDR_BYTES_MAX) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- if (dummy_cycles > FLASH_CMD_CTRL_DUMMY_CYCLES_MAX) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- if (read_requested && write_requested) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- change_bits_in_word(&flash_cmd_ctrl,
- (uint32_t)opcode,
- BITS_PER_BYTE,
- FLASH_CMD_CTRL_OPCODE_POS);
-
- /* Enable read if requested */
- if (read_requested) {
- SET_BIT(flash_cmd_ctrl, FLASH_CMD_CTRL_READ_ENABLE_POS);
- change_bits_in_word(&flash_cmd_ctrl,
- read_len - 1,
- FLASH_CMD_CTRL_READ_BYTES_BITS,
- FLASH_CMD_CTRL_READ_BYTES_POS);
- }
-
- /* Enable write if requested */
- if (write_requested) {
- SET_BIT(flash_cmd_ctrl, FLASH_CMD_CTRL_WRITE_ENABLE_POS);
- change_bits_in_word(&flash_cmd_ctrl,
- write_len - 1,
- FLASH_CMD_CTRL_WRITE_BYTES_BITS,
- FLASH_CMD_CTRL_WRITE_BYTES_POS);
-
- if (IS_ADDR_ALIGNED(write_data) && IS_ADDR_ALIGNED(write_len)) {
- /*
- * Optimised case when write_data is word aligned and write_len is
- * 4 or 8.
- */
- reg_map->flash_cmd_write_data_lower = *(uint32_t *)write_data;
- if (write_len == FLASH_CMD_CTRL_WRITE_BYTES_MAX) {
- reg_map->flash_cmd_write_data_upper =
- *((uint32_t *)write_data + 1);
- }
- } else {
- /*
- * data_regs is used as a buffer to only do unaligned access on the
- * AHB bus and word aligned accesses to the APB registers.
- */
- memcpy((void *)data_regs, write_data, write_len);
- /*
- * Only write_len bytes will be written even if both data registers
- * are written.
- */
- reg_map->flash_cmd_write_data_lower = data_regs[DATA_REG_LOWER];
- reg_map->flash_cmd_write_data_upper = data_regs[DATA_REG_UPPER];
- }
- }
-
- /* Enable the address if requested */
- if (addr_requested) {
- SET_BIT(flash_cmd_ctrl, FLASH_CMD_CTRL_ADDR_ENABLE_POS);
- reg_map->flash_cmd_addr = addr;
- change_bits_in_word(&flash_cmd_ctrl,
- addr_bytes_number - 1,
- FLASH_CMD_CTRL_ADDR_BYTES_BITS,
- FLASH_CMD_CTRL_ADDR_BYTES_POS);
- }
-
- /* Put dummy cycles number */
- change_bits_in_word(&flash_cmd_ctrl,
- dummy_cycles,
- FLASH_CMD_CTRL_DUMMY_CYCLES_BITS,
- FLASH_CMD_CTRL_DUMMY_CYCLES_POS);
-
- /* Copy the Flash Command Control register and execute the command */
- reg_map->flash_cmd_ctrl = flash_cmd_ctrl;
- SET_BIT(reg_map->flash_cmd_ctrl, FLASH_CMD_CTRL_EXECUTE_POS);
-
- /* Wait for termination */
- while (GET_BIT(reg_map->flash_cmd_ctrl, FLASH_CMD_CTRL_BUSY_POS));
-
- /*
- * Recolt the read data if it was requested. read_len validity has already
- * been verified at this point.
- */
- if (read_requested) {
- if (IS_ADDR_ALIGNED(read_data) && IS_ADDR_ALIGNED(read_len)) {
- /*
- * Optimised case when read_data is word aligned and read_len is
- * 4 or 8.
- */
- *(uint32_t *)read_data = reg_map->flash_cmd_read_data_lower;
- if (read_len == FLASH_CMD_CTRL_READ_BYTES_MAX) {
- *((uint32_t *)read_data + 1) =
- reg_map->flash_cmd_read_data_upper;
- }
- } else {
- /*
- * Only read_len bytes have been written even if both data registers
- * are written.
- */
- data_regs[DATA_REG_LOWER] = reg_map->flash_cmd_read_data_lower;
- data_regs[DATA_REG_UPPER] = reg_map->flash_cmd_read_data_upper;
- /*
- * data_regs is used as a buffer to only do unaligned access on the
- * AHB bus and word aligned accesses to the APB registers.
- */
- memcpy(read_data, (void *)data_regs, read_len);
- }
- }
-
- return QSPI_IP6514E_ERR_NONE;
-}
-
-void qspi_ip6514e_send_simple_cmd(struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode)
-{
- /*
- * No read/write data, no address, no dummy cycles.
- * Given the arguments, this function can not fail.
- */
- (void)qspi_ip6514e_send_cmd(dev,
- opcode,
- ARG_PTR_NOT_USED,
- ARG_NOT_USED,
- ARG_PTR_NOT_USED,
- ARG_NOT_USED,
- ARG_NOT_USED,
- ARG_NOT_USED,
- 0);
-}
-
-enum qspi_ip6514e_error_t qspi_ip6514e_send_read_cmd(
- struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- void *read_data,
- uint32_t read_len,
- uint32_t addr,
- uint32_t addr_bytes_number,
- uint32_t dummy_cycles)
-{
- /* Read arguments are expected */
- if (read_data == ARG_PTR_NOT_USED || read_len == ARG_NOT_USED) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- /* No write data */
- return qspi_ip6514e_send_cmd(dev,
- opcode,
- read_data,
- read_len,
- ARG_PTR_NOT_USED,
- ARG_NOT_USED,
- addr,
- addr_bytes_number,
- dummy_cycles);
-}
-
-enum qspi_ip6514e_error_t qspi_ip6514e_send_write_cmd(
- struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- const void *write_data,
- uint32_t write_len,
- uint32_t addr,
- uint32_t addr_bytes_number,
- uint32_t dummy_cycles)
-{
- /* Write arguments are expected */
- if (write_data == ARG_PTR_NOT_USED || write_len == ARG_NOT_USED) {
- return QSPI_IP6514E_ERR_WRONG_ARGUMENT;
- }
-
- /* No read data, no dummy cycles */
- return qspi_ip6514e_send_cmd(dev,
- opcode,
- ARG_PTR_NOT_USED,
- ARG_NOT_USED,
- write_data,
- write_len,
- addr,
- addr_bytes_number,
- dummy_cycles);
-}
diff --git a/platform/ext/target/musca_a/Native_Driver/qspi_ip6514e_drv.h b/platform/ext/target/musca_a/Native_Driver/qspi_ip6514e_drv.h
deleted file mode 100644
index 6992925..0000000
--- a/platform/ext/target/musca_a/Native_Driver/qspi_ip6514e_drv.h
+++ /dev/null
@@ -1,416 +0,0 @@
-/*
- * Copyright (c) 2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file qspi_ip6514e_drv.h
- * \brief Driver for Cadence QSPI Flash Controller IP.
- * There are two ways to communicate with the flash memory device:
- * - issue AHB requests for direct read and writes in the Flash memory
- * mapped address zone. The commands used for those can be configured
- * by the driver
- * - send a command to the device to access his internal registers and
- * do other operations like erasing a sector
- * At reset, the QSPI controller will work in a default mode which will
- * allow to do basic commands. It should be configured with the
- * flash memory device specifications for optimal use for commands and
- * direct reads/writes. Here is an example of configuration:
- * - send command to activate QSPI mode on the flash memory device
- * - send command to change dummy cycles on the flash memory device
- * - check if any operation is ungoing
- * - disable the QSPI controller
- * - change the baud rate divisor
- * - activate the QSPI mode on the controller
- * - change the dummy cycles number and opcode for reads/writes
- * - change the number of bytes per page
- * - change the number of address bytes
- * - activate the QSPI controller
- *
- * Warning: none of the functions declared here check if the dev
- * argument points to NULL.
- */
-
-#ifndef __QSPI_IP6514E_DRV_H__
-#define __QSPI_IP6514E_DRV_H__
-
-#include <stdint.h>
-#include <stdbool.h>
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/**
- * \brief Cadence QSPI IP6514E error enumeration types
- */
-enum qspi_ip6514e_error_t {
- QSPI_IP6514E_ERR_NONE,
- QSPI_IP6514E_ERR_WRONG_ARGUMENT,
- QSPI_IP6514E_ERR_CONTROLLER_NOT_DISABLED,
- QSPI_IP6514E_ERR_READ_IN_PROGRESS,
- QSPI_IP6514E_ERR_WRITE_IN_PROGRESS,
- /* Any new error should be added to the enumeration type error of
- * the corresponding Flash device library as well.
- */
-};
-
-/**
- * \brief Cadence QSPI IP6514E SPI modes
- */
-enum qspi_ip6514e_spi_mode_t {
- QSPI_IP6514E_SPI_MODE,
- /*!< Use 1 line for Instruction, Address and Data */
- QSPI_IP6514E_DSPI_MODE,
- /*!< Use 2 lines for Instruction, Address and Data */
- QSPI_IP6514E_QSPI_MODE,
- /*!< Use 4 lines for Instruction, Address and Data */
-};
-
-/**
- * \brief Cadence QSPI IP6514E device configuration structure
- */
-struct qspi_ip6514e_dev_cfg_t {
- const uint32_t base; /*!< QSPI IP6514E base address */
- /*
- * If not all the AHB wires are connected to the QSPI Flash Controller the
- * driver can still access all of the Flash memory. The bits of this value
- * should be put to 1 for every wire that is connected. Set it to
- * 0xFFFFFFFFU if all AHB address wires are connected to the
- * QSPI Flash Controller.
- */
- uint32_t addr_mask;
-};
-
-/**
- * \brief Cadence QSPI IP6514E device structure
- */
-struct qspi_ip6514e_dev_t {
- const struct qspi_ip6514e_dev_cfg_t* const cfg;
- /*!< QSPI IP6514E configuration */
-};
-
-/**
- * \brief Check if the controller is idle.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- *
- * \return true if the controller is idle, false otherwise.
- */
-bool qspi_ip6514e_is_idle(struct qspi_ip6514e_dev_t* dev);
-
-/**
- * \brief Check if the controller is enabled.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- *
- * \return true if the controller is enabled, false otherwise.
- */
-bool qspi_ip6514e_is_enabled(struct qspi_ip6514e_dev_t* dev);
-
-/**
- * \brief Disable the QSPI controller.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- */
-void qspi_ip6514e_disable(struct qspi_ip6514e_dev_t* dev);
-
-/**
- * \brief Enable the QSPI controller.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- */
-void qspi_ip6514e_enable(struct qspi_ip6514e_dev_t* dev);
-
-/**
- * \brief Change the baud rate divisor.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- * \param[in] div Baud rate divisor value. It can only be an even number
- * between 2 and 32 (both included).
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note The QSPI frequency is calculated dividing the QSPI controller clock by
- * this divisor. Please check Flash memory device specifications to know
- * the maximal frequency that can be used.
- * \note The QSPI controller should be disabled before calling this function.
- */
-enum qspi_ip6514e_error_t qspi_ip6514e_set_baud_rate_div(
- struct qspi_ip6514e_dev_t* dev,
- uint32_t div);
-
-/**
- * \brief Set SPI mode for instruction, address and data.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- * \param[in] inst_type SPI mode to use for the instruction part of the command
- * \param[in] addr_type SPI mode to use for the address part of the command
- * \param[in] data_type SPI mode to use for the data part of the command
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note The QSPI controller should be idle before calling this function.
- * \note Changing this setting will affect commands and direct operations.
- */
-enum qspi_ip6514e_error_t qspi_ip6514e_set_spi_mode(
- struct qspi_ip6514e_dev_t* dev,
- enum qspi_ip6514e_spi_mode_t inst_type,
- enum qspi_ip6514e_spi_mode_t addr_type,
- enum qspi_ip6514e_spi_mode_t data_type);
-
-/**
- * \brief Configure read commands for direct reads.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- * \param[in] opcode Read opcode that will be used for every direct read
- * \param[in] dummy_cycles Number of dummy cycles to wait before triggering the
- * command, this value must be between 0 and 31
- * (both included)
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note The QSPI controller should be idle before calling this function.
- */
-enum qspi_ip6514e_error_t qspi_ip6514e_cfg_reads(struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- uint32_t dummy_cycles);
-
-/**
- * \brief Configure write commands for direct writes.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- * \param[in] opcode Write opcode that will be used for every direct write
- * \param[in] dummy_cycles Number of dummy cycles to wait before triggering the
- * command, this value must be between 0 and 31
- * (both included)
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note The QSPI controller should be idle before calling this function.
- */
-enum qspi_ip6514e_error_t qspi_ip6514e_cfg_writes(
- struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- uint32_t dummy_cycles);
-
-/**
- * \brief Change the number of bytes per device page.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- * \param[in] page_size Number of bytes per device page, must be between 0
- * and 4095 (both included)
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note The QSPI controller should be idle before calling this function.
- * \note This function will affect direct reads/writes.
- */
-enum qspi_ip6514e_error_t qspi_ip6514e_cfg_page_size(
- struct qspi_ip6514e_dev_t* dev,
- uint32_t page_size);
-
-/**
- * \brief Change the number of device address bytes.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- * \param[in] bytes_number Number of device address bytes, must be between 1
- * and 16 (both included)
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note The QSPI controller should be idle before calling this function.
- * \note This function will affect direct reads/writes.
- */
-enum qspi_ip6514e_error_t qspi_ip6514e_cfg_addr_bytes(
- struct qspi_ip6514e_dev_t* dev,
- uint32_t bytes_number);
-
-/**
- * \brief Remap the incoming AHB address with an offset for direct accesses.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- * \param[in] offset Offset that will be added to the incoming AHB address to
- * access the Flash memory
- *
- * \note This function will only affect direct reads/writes.
- * \note This function does not check if the resulting address is out of memory
- * bounds.
- */
-void qspi_ip6514e_remap_addr(struct qspi_ip6514e_dev_t* dev, uint32_t offset);
-
-/**
- * \brief Disable AHB address remapping for direct accesses.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- *
- * \note This function will disable the controller if it is not already
- * disabled and enable it again (if it was).
- * \note This function will only affect direct reads/writes.
- */
-void qspi_ip6514e_disable_remap(struct qspi_ip6514e_dev_t* dev);
-
-/**
- * \brief Restore the default value of the QSPI controller registers.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- *
- * \note The QSPI controller should be disabled before calling this function.
- */
-void qspi_ip6514e_reset_regs(struct qspi_ip6514e_dev_t* dev);
-
-/**
- * \brief Send a command to the flash memory device using the Software Triggered
- * Instruction Generator (STIG).
- *
- * \param[in] dev QSPI IP6514E device struct
- * \ref qspi_ip6514e_dev_t
- * \param[in] opcode Opcode for the command.
- * \param[out] read_data Pointer to a memory zone where the read_len
- * bytes read will be written to. If no data is to
- * be read for the command,
- * this argument should be NULL.
- * \param[in] read_len Number of bytes to read for the command. If
- * no bytes are to be read, use 0 for argument
- * otherwise between 1 and 8 bytes (both
- * included) can be read.
- * \param[in] write_data Pointer to a memory zone where are
- * located the write_len bytes to write for
- * this command. If no bytes are to be written,
- * use NULL as argument.
- * \param[in] write_len Number of bytes to write for the command. If
- * no bytes are to be written, use 0 for
- * argument otherwise between 1 and 8 bytes
- * (both included) can be written.
- * \param[in] addr Address used for the command
- * \param[in] addr_bytes_number Number of address bytes for this command.
- * If an address is not needed for the command,
- * use 0 for argument, otherwise between 1 and
- * 4 bytes (both included) can be used.
- * \param[in] dummy_cycles Number of dummy cycles required for the
- * command, between 0 and 31 (both included).
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note Check the flash memory device specifications for the possible opcodes
- * that can be used and the other informations needed for this function.
- * \note The SPI mode used for this command is the one set with the
- * \ref qspi_ip6514e_activate_qspi_mode function or the default one.
- */
-enum qspi_ip6514e_error_t qspi_ip6514e_send_cmd(struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- void *read_data,
- uint32_t read_len,
- const void *write_data,
- uint32_t write_len,
- uint32_t addr,
- uint32_t addr_bytes_number,
- uint32_t dummy_cycles);
-
-/**
- * \brief Send a simple command to the flash memory device using the Software
- * Triggered Instruction Generator (STIG) with no data arguments.
- * This command can be used for example to send the WRITE ENABLE command.
- *
- * \param[in] dev QSPI IP6514E device struct \ref qspi_ip6514e_dev_t
- * \param[in] opcode Opcode for the command.
- *
- * \note Check the flash memory device specifications for the possible opcodes
- * that can be used and the other informations needed for this function.
- * \note The SPI mode used for this command is the one set with the
- * \ref qspi_ip6514e_activate_qspi_mode function or the default one.
- */
-void qspi_ip6514e_send_simple_cmd(struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode);
-
-/**
- * \brief Send a read command to the flash memory device using the Software
- * Triggered Instruction Generator (STIG). This command can be used to
- * read Flash memory data or registers.
- *
- * \param[in] dev QSPI IP6514E device struct
- * \ref qspi_ip6514e_dev_t
- * \param[in] opcode Opcode for the command.
- * \param[out] read_data Pointer to a memory zone where the
- * read_len bytes read will be written to.
- * \param[in] read_len Number of bytes to read for the command.
- * Between 1 and 8 bytes (both included) can be
- * read.
- * \param[in] addr Address used for the command
- * \param[in] addr_bytes_number Number of address bytes for this command.
- * If an address is not needed for the command,
- * use 0 for argument, otherwise between 1 and
- * 4 bytes (both included) can be used.
- * \param[in] dummy_cycles Number of dummy cycles required for the
- * command, between 0 and 31 (both included).
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note Check the flash memory device specifications for the possible opcodes
- * that can be used and the other informations needed for this function.
- * \note The SPI mode used for this command is the one set with the
- * \ref qspi_ip6514e_activate_qspi_mode function or the default one.
- */
-enum qspi_ip6514e_error_t qspi_ip6514e_send_read_cmd(
- struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- void *read_data,
- uint32_t read_len,
- uint32_t addr,
- uint32_t addr_bytes_number,
- uint32_t dummy_cycles);
-
-/**
- * \brief Send a write command to the flash memory device using the Software
- * Triggered Instruction Generator (STIG). This command can be used to
- * write Flash memory or registers.
- *
- * \param[in] dev QSPI IP6514E device struct
- * \ref qspi_ip6514e_dev_t
- * \param[in] opcode Opcode for the command.
- * \param[in] write_data Pointer to a memory zone where are
- * located the write_len bytes to write for
- * this command.
- * \param[in] write_len Number of bytes to write for the command.
- * Between 1 and 8 bytes (both included) can be
- * written.
- * \param[in] addr Address used for the command
- * \param[in] addr_bytes_number Number of address bytes for this command.
- * If an address is not needed for the command,
- * use 0 for argument, otherwise between 1 and
- * 4 bytes (both included) can be used.
- * \param[in] dummy_cycles Number of dummy cycles required for the
- * command, between 0 and 31 (both included).
- *
- * \return Returns error code as specified in \ref qspi_ip6514e_error_t
- *
- * \note Check the flash memory device specifications for the possible opcodes
- * that can be used and the other informations needed for this function.
- * \note The SPI mode used for this command is the one set with the
- * \ref qspi_ip6514e_activate_qspi_mode function or the default one.
- */
-enum qspi_ip6514e_error_t qspi_ip6514e_send_write_cmd(
- struct qspi_ip6514e_dev_t* dev,
- uint8_t opcode,
- const void *write_data,
- uint32_t write_len,
- uint32_t addr,
- uint32_t addr_bytes_number,
- uint32_t dummy_cycles);
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __QSPI_IP6514E_DRV_H__ */
diff --git a/platform/ext/target/musca_a/Native_Driver/timer_cmsdk_drv.c b/platform/ext/target/musca_a/Native_Driver/timer_cmsdk_drv.c
deleted file mode 100644
index f4d477b..0000000
--- a/platform/ext/target/musca_a/Native_Driver/timer_cmsdk_drv.c
+++ /dev/null
@@ -1,223 +0,0 @@
-/*
- * Copyright (c) 2016-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file timer_cmsdk_drv.c
- * \brief Generic driver for CMSDK APB Timers.
- * The timer is a 32-bit down-counter with the following features:
- * - optional programmable external clock source
- * - programmable interrupt source, triggered if counter reaches 0
- * - automatic reload if counter reaches 0
- */
-
-#include "timer_cmsdk_drv.h"
-
-/** Setter bit manipulation macro */
-#define SET_BIT(WORD, BIT_INDEX) ((WORD) |= (1U << (BIT_INDEX)))
-/** Clearing bit manipulation macro */
-#define CLR_BIT(WORD, BIT_INDEX) ((WORD) &= ~(1U << (BIT_INDEX)))
-/** Getter bit manipulation macro */
-#define GET_BIT(WORD, BIT_INDEX) (bool)(((WORD) & (1U << (BIT_INDEX))))
-
-/**
- * \brief Timer register map structure
- *
- */
-struct timer_cmsdk_reg_map_t {
- volatile uint32_t ctrl; /* Offset: 0x000 (R/W) control register */
- volatile uint32_t value; /* Offset: 0x004 (R/W) current value register */
- volatile uint32_t reload; /* Offset: 0x008 (R/W) reload value register */
- union {
- volatile uint32_t intstatus; /* Offset: 0x00C (R/ ) interrupt
- * status register */
- volatile uint32_t intclear; /* Offset: 0x00C ( /W) interrupt
- * clear register */
- }intreg;
-};
-
-/**
- * \brief CTRL register bit definitions
- *
- */
-enum ctrl_reg_bits_t{
- CTRL_REG_ENUM_ENABLE_INDEX = 0,
- CTRL_REG_ENUM_EXTERNAL_INPUT_ENABLE_INDEX = 1,
- CTRL_REG_ENUM_EXTERNAL_INPUT_CLOCK_INDEX = 2,
- CTRL_REG_ENUM_IRQ_ENABLE_INDEX = 3
-};
-
-/**
- * \brief INTSTATUS/INTCLEAR register bit definitions
- *
- */
-enum interrupt_reg_bits_t{
- INTERRUPT_REG_ENUM_STATUS_AND_CLEAR_INDEX = 0
-};
-
-void timer_cmsdk_init(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
-
- if (dev->data->is_initialized == 0) {
- register_map->ctrl = 0;
- register_map->reload = TIMER_CMSDK_DEFAULT_RELOAD;
- dev->data->is_initialized = 1;
- }
-}
-
-bool timer_cmsdk_is_initialized(const struct timer_cmsdk_dev_t* dev)
-{
- return dev->data->is_initialized;
-}
-
-void timer_cmsdk_enable_external_input(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- SET_BIT(register_map->ctrl, CTRL_REG_ENUM_EXTERNAL_INPUT_ENABLE_INDEX);
-}
-
-void timer_cmsdk_disable_external_input(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- CLR_BIT(register_map->ctrl, CTRL_REG_ENUM_EXTERNAL_INPUT_ENABLE_INDEX);
-}
-
-bool timer_cmsdk_is_external_input_enabled(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- return GET_BIT(register_map->ctrl,
- CTRL_REG_ENUM_EXTERNAL_INPUT_ENABLE_INDEX);
-}
-
-void timer_cmsdk_set_clock_to_internal(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- CLR_BIT(register_map->ctrl, CTRL_REG_ENUM_EXTERNAL_INPUT_CLOCK_INDEX);
-}
-
-void timer_cmsdk_set_clock_to_external(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- SET_BIT(register_map->ctrl, CTRL_REG_ENUM_EXTERNAL_INPUT_CLOCK_INDEX);
-}
-
-bool timer_cmsdk_is_clock_external(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- return GET_BIT(register_map->ctrl,
- CTRL_REG_ENUM_EXTERNAL_INPUT_CLOCK_INDEX);
-}
-
-void timer_cmsdk_enable(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- SET_BIT(register_map->ctrl, CTRL_REG_ENUM_ENABLE_INDEX);
-}
-
-void timer_cmsdk_disable(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- CLR_BIT(register_map->ctrl, CTRL_REG_ENUM_ENABLE_INDEX);
-}
-
-bool timer_cmsdk_is_enabled(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- return GET_BIT(register_map->ctrl, CTRL_REG_ENUM_ENABLE_INDEX);
-}
-
-void timer_cmsdk_enable_interrupt(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- SET_BIT(register_map->ctrl, CTRL_REG_ENUM_IRQ_ENABLE_INDEX);
-}
-
-void timer_cmsdk_disable_interrupt(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- CLR_BIT(register_map->ctrl, CTRL_REG_ENUM_IRQ_ENABLE_INDEX);
-}
-
-bool timer_cmsdk_is_interrupt_enabled(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- return GET_BIT(register_map->ctrl, CTRL_REG_ENUM_IRQ_ENABLE_INDEX);
-}
-
-bool timer_cmsdk_is_interrupt_active(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- return GET_BIT(register_map->intreg.intstatus,
- INTERRUPT_REG_ENUM_STATUS_AND_CLEAR_INDEX);
-}
-
-void timer_cmsdk_clear_interrupt(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- SET_BIT(register_map->intreg.intclear,
- INTERRUPT_REG_ENUM_STATUS_AND_CLEAR_INDEX);
-}
-
-uint32_t timer_cmsdk_get_current_value(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- return register_map->value;
-}
-
-void timer_cmsdk_set_reload_value(const struct timer_cmsdk_dev_t* dev,
- uint32_t reload)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- register_map->reload = reload;
-}
-
-void timer_cmsdk_reset(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- register_map->value = register_map->reload;
-}
-
-uint32_t timer_cmsdk_get_reload_value(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- return register_map->reload;
-}
-
-uint32_t timer_cmsdk_get_elapsed_value(const struct timer_cmsdk_dev_t* dev)
-{
- struct timer_cmsdk_reg_map_t* register_map =
- (struct timer_cmsdk_reg_map_t*)dev->cfg->base;
- return register_map->reload - register_map->value;
-}
diff --git a/platform/ext/target/musca_a/Native_Driver/timer_cmsdk_drv.h b/platform/ext/target/musca_a/Native_Driver/timer_cmsdk_drv.h
deleted file mode 100644
index 4c41fea..0000000
--- a/platform/ext/target/musca_a/Native_Driver/timer_cmsdk_drv.h
+++ /dev/null
@@ -1,254 +0,0 @@
-/*
- * Copyright (c) 2016-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file timer_cmsdk_drv.h
- * \brief Generic driver for CMSDK APB Timers.
- * The timer is a 32-bit down-counter with the following features:
- * - optional programmable external clock source
- * - programmable interrupt source, triggered if counter reaches 0
- * - automatic reload if counter reaches 0
- */
-
-#ifndef __TIMER_CMSDK_DRV_H__
-#define __TIMER_CMSDK_DRV_H__
-
-#include <stdint.h>
-#include <stdbool.h>
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/* Maximum reload value */
-#define TIMER_CMSDK_MAX_RELOAD UINT32_MAX /* max of 32-bit */
-#define TIMER_CMSDK_DEFAULT_RELOAD TIMER_CMSDK_MAX_RELOAD
-
-/** CMSDK timer device configuration structure */
-struct timer_cmsdk_dev_cfg_t {
- const uintptr_t base; /*!< Timer base address */
-};
-
-/** CMSDK timer device data structure */
-struct timer_cmsdk_dev_data_t {
- bool is_initialized; /*!< Indicates if the timer is initialized */
-};
-
-/* CMSDK timer device structure */
-struct timer_cmsdk_dev_t {
- const struct timer_cmsdk_dev_cfg_t* const cfg; /*!< Timer configuration */
- struct timer_cmsdk_dev_data_t* const data; /*!< Timer data */
-};
-
-/**
- * \brief Initializes timer to a known default state, which is:
- * - timer disabled
- * - timer interrupt disabled
- * - clock source set to internal
- * - external input disabled
- * - reload value maxed out
- * Init should be called prior to any other process and
- * it's the caller's responsibility to follow proper call order.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_init(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Checks if a timer is initialized.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- *
- * \return true if initialized, false otherwise
- */
-bool timer_cmsdk_is_initialized(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Enables external input, which could be used as clock source
- * by calling \ref timer_cmsdk_set_clock_to_external.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_enable_external_input(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Disables external input.
- * Make sure if the timer is explicitly wanted to be stopped or set
- * the clock source to internal by \ref timer_cmsdk_set_clock_to_internal.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_disable_external_input(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Checks if external input is enabled.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- *
- * \return true if enabled, false otherwise
- */
-bool timer_cmsdk_is_external_input_enabled(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Sets the clock source to internal.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_set_clock_to_internal(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Sets the clock source to external.
- * Make sure external input is enabled correspondingly
- * by \ref timer_cmsdk_enable_external_input.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_set_clock_to_external(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Checks if clock source is external input.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- *
- * \return true if external, false if internal
- */
-bool timer_cmsdk_is_clock_external(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Enables timer operation.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_enable(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Disables the given hardware timer.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_disable(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Checks if a timer is enabled.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- *
- * \return true if enabled, false otherwise
- */
-bool timer_cmsdk_is_enabled(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Enables timer interrupt.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_enable_interrupt(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Disables timer interrupt.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_disable_interrupt(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Checks if a timer interrupt is enabled.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- *
- * \return true if enabled, false otherwise
- */
-bool timer_cmsdk_is_interrupt_enabled(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Gets timer interrupt status
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- *
- * * \return true if active, false otherwise
- */
-bool timer_cmsdk_is_interrupt_active(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Clears timer interrupt
- * The interrupt request is held until it is cleared.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_clear_interrupt(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Reads timer current value.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- *
- * \return Timer value
- */
-uint32_t timer_cmsdk_get_current_value(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Sets the reload value of the selected timer.
- *
- * New reload value takes effect when:
- * - timer is restarted
- * - on timer underflow
- * - when timer_cmsdk_reset is called
- *
- * \note In r1p0 technical reference manual it's incorrectly stated
- * writing the reload value automatically sets the current value also.
- * r1p1 technical reference manual includes the fix.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- * \param[in] reload Timer reload value to set.
- * This is the start value of the 32-bit down counter,
- * which automatically reloaded if 0 is reached.
- */
-void timer_cmsdk_set_reload_value(const struct timer_cmsdk_dev_t* dev,
- uint32_t reload);
-
-/**
- * \brief Resets the timer counter to the reload value instantly
- * (i.e. without waiting for underflow).
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- */
-void timer_cmsdk_reset(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Gets the reload value of the selected timer.
- * This is the start value of the 32-bit down counter,
- * which is automatically reloaded if 0 is reached by the counter.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- *
- * \return Reload value of the selected timer.
- */
-uint32_t timer_cmsdk_get_reload_value(const struct timer_cmsdk_dev_t* dev);
-
-/**
- * \brief Reads the number of ticks elapsed in the current cycle.
- *
- * \param[in] dev Timer configuration \ref timer_cmsdk_dev_t
- *
- * \return Get elapsed number of ticks since last reload was set.
- * Elapsed = (Reload value - Current value)
- */
-uint32_t timer_cmsdk_get_elapsed_value(const struct timer_cmsdk_dev_t* dev);
-
-#ifdef __cplusplus
-}
-#endif
-#endif /* __TIMER_CMSDK_DRV_H__ */
diff --git a/platform/ext/target/musca_a/Native_Driver/uart_pl011_drv.c b/platform/ext/target/musca_a/Native_Driver/uart_pl011_drv.c
deleted file mode 100644
index 01feaa4..0000000
--- a/platform/ext/target/musca_a/Native_Driver/uart_pl011_drv.c
+++ /dev/null
@@ -1,1019 +0,0 @@
-/*
- * Copyright (c) 2016-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include "uart_pl011_drv.h"
-
-#include <stddef.h>
-#include "cmsis_compiler.h"
-
-#define FREQ_IRLPBAUD16_MIN (1420000u) /* 1.42 MHz */
-#define FREQ_IRLPBAUD16_MAX (2120000u) /* 2.12 MHz */
-#define SAMPLING_FACTOR (16u)
-#define UART_PL011_FBRD_WIDTH (6u)
-
-/**
- * \brief UART PL011 register map structure
- */
-struct _uart_pl011_reg_map_t {
- volatile uint32_t uartdr; /*!< Offset: 0x000 (R/W) Data register */
- union {
- volatile uint32_t uartrsr;
- /*!< Offset: 0x004 (R/ ) Receive status register */
- volatile uint32_t uartecr;
- /*!< Offset: 0x004 ( /W) Error clear register */
- };
- volatile uint32_t reserved_0[4]; /*!< Offset: 0x008-0x014 Reserved */
- volatile uint32_t uartfr; /*!< Offset: 0x018 (R/ ) Flag register */
- volatile uint32_t reserved_1; /*!< Offset: 0x01C Reserved */
- volatile uint32_t uartilpr;
- /*!< Offset: 0x020 (R/W) IrDA low-power counter register */
- volatile uint32_t uartibrd;
- /*!< Offset: 0x024 (R/W) Integer baud rate register */
- volatile uint32_t uartfbrd;
- /*!< Offset: 0x028 (R/W) Fractional baud rate register */
- volatile uint32_t uartlcr_h;
- /*!< Offset: 0x02C (R/W) Line control register */
- volatile uint32_t uartcr;
- /*!< Offset: 0x030 (R/W) Control register */
- volatile uint32_t uartifls;
- /*!< Offset: 0x034 (R/W) Interrupt FIFO level select register */
- volatile uint32_t uartimsc;
- /*!< Offset: 0x038 (R/W) Interrupt mask set/clear register */
- volatile uint32_t uartris;
- /*!< Offset: 0x03C (R/ ) Raw interrupt status register */
- volatile uint32_t uartmis;
- /*!< Offset: 0x040 (R/ ) Masked interrupt status register */
- volatile uint32_t uarticr;
- /*!< Offset: 0x044 ( /W) Interrupt clear register */
- volatile uint32_t uartdmacr;
- /*!< Offset: 0x048 (R/W) DMA control register */
- volatile uint32_t reserved_2[13]; /*!< Offset: 0x04C-0x07C Reserved */
- volatile uint32_t reserved_3[4];
- /*!< Offset: 0x080-0x08C Reserved for test purposes */
- volatile uint32_t reserved_4[976]; /*!< Offset: 0x090-0xFCC Reserved */
- volatile uint32_t reserved_5[4];
- /*!< Offset: 0xFD0-0xFDC Reserved for future ID expansion */
- volatile uint32_t uartperiphid0;
- /*!< Offset: 0xFE0 (R/ ) UARTPeriphID0 register */
- volatile uint32_t uartperiphid1;
- /*!< Offset: 0xFE4 (R/ ) UARTPeriphID1 register */
- volatile uint32_t uartperiphid2;
- /*!< Offset: 0xFE8 (R/ ) UARTPeriphID2 register */
- volatile uint32_t uartperiphid3;
- /*!< Offset: 0xFEC (R/ ) UARTPeriphID3 register */
- volatile uint32_t uartpcellid0;
- /*!< Offset: 0xFF0 (R/ ) UARTPCellID0 register */
- volatile uint32_t uartpcellid1;
- /*!< Offset: 0xFF4 (R/ ) UARTPCellID1 register */
- volatile uint32_t uartpcellid2;
- /*!< Offset: 0xFF8 (R/ ) UARTPCellID2 register */
- volatile uint32_t uartpcellid3;
- /*!< Offset: 0xFFC (R/ ) UARTPCellID3 register */
-};
-
-#define UART_PL011_UARTFR_CTS_MASK ( \
- 0x1u<<UART_PL011_UARTFR_CTS_OFF)
-#define UART_PL011_UARTFR_DSR_MASK ( \
- 0x1u<<UART_PL011_UARTFR_DSR_OFF)
-#define UART_PL011_UARTFR_DCD_MASK ( \
- 0x1u<<UART_PL011_UARTFR_DCD_OFF)
-#define UART_PL011_UARTFR_BUSYBIT ( \
- 0x1u<<UART_PL011_UARTFR_BUSYBIT_OFF)
-#define UART_PL011_UARTFR_RX_FIFO_EMPTY ( \
- 0x1u<<UART_PL011_UARTFR_RX_FIFO_EMPTY_OFF)
-#define UART_PL011_UARTFR_TX_FIFO_FULL ( \
- 0x1u<<UART_PL011_UARTFR_TX_FIFO_FULL_OFF)
-#define UART_PL011_UARTFR_RI_MASK ( \
- 0x1u<<UART_PL011_UARTFR_RI_OFF)
-
-#define UART_PL011_UARTLCR_H_BRK_MASK ( \
- 0x1u<<UART_PL011_UARTLCR_H_BRK_OFF)
-#define UART_PL011_UARTLCR_H_PARITY_MASK ( \
- 0x1u<<UART_PL011_UARTLCR_H_PEN_OFF \
- | 0x1u<<UART_PL011_UARTLCR_H_EPS_OFF \
- | 0x1u<<UART_PL011_UARTLCR_H_SPS_OFF)
-#define UART_PL011_UARTLCR_H_STOPBIT_MASK ( \
- 0x1u<<UART_PL011_UARTLCR_H_STP2_OFF)
-#define UART_PL011_UARTLCR_H_FEN_MASK ( \
- 0x1u<<UART_PL011_UARTLCR_H_FEN_OFF)
-#define UART_PL011_UARTLCR_H_WLEN_MASK ( \
- 0x3u<<UART_PL011_UARTLCR_H_WLEN_OFF)
-#define UART_PL011_FORMAT_MASK ( \
- UART_PL011_UARTLCR_H_PARITY_MASK \
- | UART_PL011_UARTLCR_H_STOPBIT_MASK \
- | UART_PL011_UARTLCR_H_WLEN_MASK)
-
-#define UART_PL011_UARTCR_EN_MASK ( \
- 0x1u<<UART_PL011_UARTCR_UARTEN_OFF)
-#define UART_PL011_UARTCR_SIREN_MASK ( \
- 0x1u<<UART_PL011_UARTCR_SIREN_OFF)
-#define UART_PL011_UARTCR_SIRLP_MASK ( \
- 0x1u<<UART_PL011_UARTCR_SIRLP_OFF)
-#define UART_PL011_UARTCR_LBE_MASK ( \
- 0x1u<<UART_PL011_UARTCR_LBE_OFF)
-#define UART_PL011_UARTCR_TX_EN_MASK ( \
- 0x1u<<UART_PL011_UARTCR_TXE_OFF)
-#define UART_PL011_UARTCR_RX_EN_MASK ( \
- 0x1u<<UART_PL011_UARTCR_RXE_OFF)
-#define UART_PL011_UARTCR_DTR_MASK ( \
- 0x1u<<UART_PL011_UARTCR_DTR_OFF)
-#define UART_PL011_UARTCR_RTS_MASK ( \
- 0x1u<<UART_PL011_UARTCR_RTS_OFF)
-#define UART_PL011_UARTCR_OUT1_MASK ( \
- 0x1u<<UART_PL011_UARTCR_OUT1_OFF)
-#define UART_PL011_UARTCR_OUT2_MASK ( \
- 0x1u<<UART_PL011_UARTCR_OUT2_OFF)
-#define UART_PL011_UARTCR_RTSE_MASK ( \
- 0x1u<<UART_PL011_UARTCR_RTSE_OFF)
-#define UART_PL011_UARTCR_CTSE_MASK ( \
- 0x1u<<UART_PL011_UARTCR_CTSE_OFF)
-
-#define UART_PL011_UARTIFLS_TX_FIFO_LVL_MASK ( \
- 0x7u<<UART_PL011_UARTIFLS_TX_OFF)
-#define UART_PL011_UARTIFLS_RX_FIFO_LVL_MASK ( \
- 0x7u<<UART_PL011_UARTIFLS_RX_OFF)
-
-#define UART_PL011_UARTDMACR_RX_MASK ( \
- 0x1u<<UART_PL011_UARTDMACR_RXEN_OFF \
- | 0x1u<<UART_PL011_UARTDMACR_ON_ERR_OFF)
-#define UART_PL011_UARTDMACR_TX_MASK ( \
- 0x1u<<UART_PL011_UARTDMACR_TXEN_OFF)
-
-/* Default register values of UART PL011 */
-#define UART_PL011_DATA_REG_RESET_VALUE (0x0u)
-#define UART_PL011_ECR_REG_CLEAR_VALUE (0xFFu)
-#define UART_PL011_ILPR_REG_RESET_VALUE (0x0u)
-#define UART_PL011_IBRD_REG_RESET_VALUE (0x0u)
-#define UART_PL011_FBRD_REG_RESET_VALUE (0x0u)
-#define UART_PL011_LCR_H_REG_RESET_VALUE (0x0u)
-#define UART_PL011_CR_REG_RESET_VALUE (0x0300u)
-#define UART_PL011_IFLS_REG_RESET_VALUE (0x12u)
-#define UART_PL011_IMSC_REG_RESET_VALUE (0x0u)
-#define UART_PL011_ICR_REG_CLEAR_VALUE (0x7FFu)
-#define UART_PL011_DMACR_REG_RESET_VALUE (0x0u)
-
-static void _uart_pl011_enable(struct _uart_pl011_reg_map_t* p_uart)
-{
- p_uart->uartcr |= UART_PL011_UARTCR_EN_MASK;
-}
-
-static void _uart_pl011_disable(struct _uart_pl011_reg_map_t* p_uart)
-{
- p_uart->uartcr &= ~UART_PL011_UARTCR_EN_MASK;
-}
-
-static bool _uart_pl011_is_enabled(struct _uart_pl011_reg_map_t* p_uart)
-{
- return (bool)(p_uart->uartcr & UART_PL011_UARTCR_EN_MASK);
-}
-
-static void _uart_pl011_enable_fifo(struct _uart_pl011_reg_map_t* p_uart)
-{
- p_uart->uartlcr_h |= UART_PL011_UARTLCR_H_FEN_MASK;
-}
-
-static void _uart_pl011_disable_fifo(struct _uart_pl011_reg_map_t* p_uart)
-{
- p_uart->uartlcr_h &= ~UART_PL011_UARTLCR_H_FEN_MASK;
-}
-
-static bool _uart_pl011_is_fifo_enabled(struct _uart_pl011_reg_map_t* p_uart)
-{
- return (bool)(p_uart->uartlcr_h & UART_PL011_UARTLCR_H_FEN_MASK);
-}
-
-static bool _uart_pl011_is_busy(struct _uart_pl011_reg_map_t* p_uart)
-{
- return (bool)(p_uart->uartfr & UART_PL011_UARTFR_BUSYBIT);
-}
-
-static enum uart_pl011_error_t _uart_pl011_set_baudrate(
- struct _uart_pl011_reg_map_t* p_uart,
- uint32_t clk, uint32_t baudrate)
-{
- /* Avoiding float calculations, bauddiv is left shifted by 6 */
- uint64_t bauddiv = (((uint64_t)clk)<<UART_PL011_FBRD_WIDTH)
- /(SAMPLING_FACTOR*baudrate);
-
- /* Valid bauddiv value
- * uart_clk (min) >= 16 x baud_rate (max)
- * uart_clk (max) <= 16 x 65535 x baud_rate (min)
- */
- if((bauddiv < (1u<<UART_PL011_FBRD_WIDTH))
- || (bauddiv > (65535u<<UART_PL011_FBRD_WIDTH))) {
- return UART_PL011_ERR_INVALID_BAUD;
- }
-
- p_uart->uartibrd = (uint32_t)(bauddiv >> UART_PL011_FBRD_WIDTH);
- p_uart->uartfbrd = (uint32_t)(bauddiv &
- ((1u << UART_PL011_FBRD_WIDTH) - 1u));
-
- __DMB();
-
- /* In order to internally update the contents of uartibrd or uartfbrd, a
- * uartlcr_h write must always be performed at the end
- * ARM DDI 0183F, Pg 3-13
- */
- p_uart->uartlcr_h = p_uart->uartlcr_h;
-
- return UART_PL011_ERR_NONE;
-}
-
-static void _uart_pl011_set_format(struct _uart_pl011_reg_map_t* p_uart,
- enum uart_pl011_wlen_t word_len,
- enum uart_pl011_parity_t parity,
- enum uart_pl011_stopbit_t stop_bits)
-{
- uint32_t ctrl_reg = p_uart->uartlcr_h & ~(UART_PL011_FORMAT_MASK);
-
- /* Making sure other bit are not changed */
- word_len &= UART_PL011_UARTLCR_H_WLEN_MASK;
- parity &= UART_PL011_UARTLCR_H_PARITY_MASK;
- stop_bits &= UART_PL011_UARTLCR_H_STOPBIT_MASK;
-
- p_uart->uartlcr_h = ctrl_reg | word_len | parity | stop_bits;
-
-}
-
-static void _uart_pl011_set_cr_bit(struct _uart_pl011_reg_map_t* p_uart,
- uint32_t mask)
-{
- bool uart_enabled = _uart_pl011_is_enabled(p_uart);
- bool fifo_enabled = _uart_pl011_is_fifo_enabled(p_uart);
-
- /* UART must be disabled before any Control Register or
- * Line Control Register are reprogrammed */
- _uart_pl011_disable(p_uart);
-
- /* Flush the transmit FIFO by disabling bit 4 (FEN) in
- * the line control register (UARTCLR_H) */
- _uart_pl011_disable_fifo(p_uart);
-
- p_uart->uartcr |= (mask);
-
- /* Enabling the FIFOs if previously enabled */
- if(fifo_enabled) {
- _uart_pl011_enable_fifo(p_uart);
- }
-
- /* Enabling the UART if previously enabled */
- if(uart_enabled) {
- _uart_pl011_enable(p_uart);
- }
-}
-
-static void _uart_pl011_clear_cr_bit(struct _uart_pl011_reg_map_t* p_uart,
- uint32_t mask)
-{
- bool uart_enabled = _uart_pl011_is_enabled(p_uart);
- bool fifo_enabled = _uart_pl011_is_fifo_enabled(p_uart);
-
- /* UART must be disabled before any Control Register or
- * Line Control Register are reprogrammed */
- _uart_pl011_disable(p_uart);
-
- /* Flush the transmit FIFO by disabling bit 4 (FEN) in
- * the line control register (UARTCLR_H) */
- _uart_pl011_disable_fifo(p_uart);
-
- p_uart->uartcr &= ~(mask);
-
- /* Enabling the FIFOs if previously enabled */
- if(fifo_enabled) {
- _uart_pl011_enable_fifo(p_uart);
- }
-
- /* Enabling the UART if previously enabled */
- if(uart_enabled) {
- _uart_pl011_enable(p_uart);
- }
-}
-
-static void _uart_pl011_set_lcr_h_bit(struct _uart_pl011_reg_map_t* p_uart,
- uint32_t mask)
-{
- bool uart_enabled = _uart_pl011_is_enabled(p_uart);
-
- /* UART must be disabled before any Control Register or
- * Line Control Register are reprogrammed */
- _uart_pl011_disable(p_uart);
-
- p_uart->uartlcr_h |= (mask);
-
- /* Enabling the UART if previously enabled */
- if(uart_enabled) {
- _uart_pl011_enable(p_uart);
- }
-}
-
-static void _uart_pl011_clear_lcr_h_bit(struct _uart_pl011_reg_map_t* p_uart,
- uint32_t mask)
-{
- bool uart_enabled = _uart_pl011_is_enabled(p_uart);
-
- /* UART must be disabled before any Control Register or
- * Line Control Register are reprogrammed */
- _uart_pl011_disable(p_uart);
-
- p_uart->uartlcr_h &= ~(mask);
-
- /* Enabling the UART if previously enabled */
- if(uart_enabled) {
- _uart_pl011_enable(p_uart);
- }
-}
-
-static void _uart_pl011_reset_regs(struct _uart_pl011_reg_map_t* p_uart)
-{
- /* Restore the default value of UART registers, the registers which
- * are not listed below are Read-Only */
-
- /* Will disable the UART */
- p_uart->uartcr = UART_PL011_CR_REG_RESET_VALUE;
- p_uart->uartdr = UART_PL011_DATA_REG_RESET_VALUE;
- /* Clear all the errors */
- p_uart->uartecr = UART_PL011_ECR_REG_CLEAR_VALUE;
- p_uart->uartilpr = UART_PL011_ILPR_REG_RESET_VALUE;
- p_uart->uartibrd = UART_PL011_IBRD_REG_RESET_VALUE;
- p_uart->uartfbrd = UART_PL011_FBRD_REG_RESET_VALUE;
- p_uart->uartlcr_h = UART_PL011_LCR_H_REG_RESET_VALUE;
- p_uart->uartifls = UART_PL011_IFLS_REG_RESET_VALUE;
- p_uart->uartimsc = UART_PL011_IMSC_REG_RESET_VALUE;
- /* Clear all the interrupts */
- p_uart->uarticr = UART_PL011_ICR_REG_CLEAR_VALUE;
- p_uart->uartdmacr = UART_PL011_DMACR_REG_RESET_VALUE;
-}
-
-enum uart_pl011_error_t uart_pl011_init(struct uart_pl011_dev_t* dev,
- uint32_t uart_clk)
-{
- enum uart_pl011_error_t err;
-
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- uint32_t def_baud = dev->cfg->def_baudrate;
-
- if(uart_clk == 0) {
- return UART_PL011_ERR_INVALID_ARG;
- }
-
- if(def_baud == 0) {
- return UART_PL011_ERR_INVALID_BAUD;
- }
-
- /* Updating the system clock */
- dev->data->uart_clk = uart_clk;
-
- /* Setting the default baudrate */
- err = _uart_pl011_set_baudrate(p_uart, uart_clk, def_baud);
-
- if(err != UART_PL011_ERR_NONE) {
- return err;
- }
-
- /* Setting the default character format */
- _uart_pl011_set_format(p_uart, dev->cfg->def_wlen,
- dev->cfg->def_parity,
- dev->cfg->def_stopbit);
-
- /* Enabling the FIFOs */
- _uart_pl011_enable_fifo(p_uart);
-
- dev->data->state = UART_PL011_INITIALIZED;
-
- return UART_PL011_ERR_NONE;
-}
-
-void uart_pl011_uninit(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- while(_uart_pl011_is_busy(p_uart));
-
- /* Disable and restore the default configuration of the peripheral */
- _uart_pl011_reset_regs(p_uart);
-
- dev->data->state = UART_PL011_UNINITIALIZED;
-
- return;
-}
-
-enum uart_pl011_state_t uart_pl011_get_state(struct uart_pl011_dev_t* dev)
-{
- return dev->data->state;
-}
-
-enum uart_pl011_error_t uart_pl011_set_baudrate(
- struct uart_pl011_dev_t* dev, uint32_t baudrate)
-{
- enum uart_pl011_error_t err = UART_PL011_ERR_NONE;
-
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- bool uart_enabled = _uart_pl011_is_enabled(p_uart);
-
- if(uart_pl011_get_state(dev) != UART_PL011_INITIALIZED) {
- return UART_PL011_ERR_NOT_INIT;
- }
-
- if(baudrate == 0) {
- return UART_PL011_ERR_INVALID_BAUD;
- }
-
- /* UART must be disabled before any Control Register or
- * Line Control Register are reprogrammed */
- _uart_pl011_disable(p_uart);
-
- /* If baudrate is not valid ie UART_PL011_ERR_NONE is not returned then
- * the UART will continue to function at the old baudrate */
- err = _uart_pl011_set_baudrate(p_uart, dev->data->uart_clk, baudrate);
-
- if(err == UART_PL011_ERR_NONE) {
- dev->data->baudrate = baudrate;
- }
-
- if(uart_enabled) {
- _uart_pl011_enable(p_uart);
- }
-
- return err;
-}
-
-uint32_t uart_pl011_get_baudrate(struct uart_pl011_dev_t* dev)
-{
- return dev->data->baudrate;
-}
-
-void uart_pl011_enable_intr(struct uart_pl011_dev_t* dev,
- enum uart_pl011_intr_t mask)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- p_uart->uartimsc |= (uint32_t)(mask);
-
- return;
-}
-
-void uart_pl011_disable_intr(struct uart_pl011_dev_t* dev,
- enum uart_pl011_intr_t mask)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- p_uart->uartimsc &= (uint32_t)(~mask);
-
- return;
-}
-
-void uart_pl011_clear_intr(struct uart_pl011_dev_t* dev,
- enum uart_pl011_intr_t mask)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- p_uart->uarticr = (uint32_t)mask;
-
- return;
-}
-
-
-enum uart_pl011_intr_t uart_pl011_get_masked_intr_status(
- struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- return (enum uart_pl011_intr_t)(p_uart->uartmis);
-
-}
-
-enum uart_pl011_intr_t uart_pl011_get_raw_intr_status(
- struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- return (enum uart_pl011_intr_t)(p_uart->uartris);
-}
-
-void uart_pl011_set_rx_fifo_lvl(struct uart_pl011_dev_t* dev,
- enum uart_pl011_rx_fifo_lvl_t rx_lvl)
-{
- uint32_t fifo_lvl;
-
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- /* Check if rx_lvl have valid values */
- rx_lvl &= UART_PL011_UARTIFLS_RX_FIFO_LVL_MASK;
-
- fifo_lvl = p_uart->uartifls
- & ~(UART_PL011_UARTIFLS_RX_FIFO_LVL_MASK);
- p_uart->uartifls = fifo_lvl | rx_lvl;
-
- return;
-}
-
-void uart_pl011_set_tx_fifo_lvl(struct uart_pl011_dev_t* dev,
- enum uart_pl011_tx_fifo_lvl_t tx_lvl)
-{
- uint32_t fifo_lvl;
-
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
- /* Check if tx_lvl have valid values */
- tx_lvl &= UART_PL011_UARTIFLS_TX_FIFO_LVL_MASK;
-
- fifo_lvl = p_uart->uartifls
- & ~(UART_PL011_UARTIFLS_TX_FIFO_LVL_MASK);
- p_uart->uartifls = fifo_lvl | tx_lvl;
-
- return;
-}
-
-void uart_pl011_set_tx_dma(struct uart_pl011_dev_t* dev,
- enum uart_pl011_tx_dma_t enable)
-{
- uint32_t dma_cr;
-
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- enable &= UART_PL011_UARTDMACR_TX_MASK;
-
- dma_cr = p_uart->uartdmacr
- & ~(UART_PL011_UARTDMACR_TX_MASK);
-
- p_uart->uartdmacr = dma_cr | enable;
-
- return;
-}
-
-void uart_pl011_set_rx_dma(struct uart_pl011_dev_t* dev,
- enum uart_pl011_rx_dma_t enable)
-{
- uint32_t dma_cr;
-
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- enable &= UART_PL011_UARTDMACR_RX_MASK;
-
- dma_cr = p_uart->uartdmacr
- & ~(UART_PL011_UARTDMACR_RX_MASK);
-
- p_uart->uartdmacr = dma_cr | enable;
-
- return;
-}
-
-bool uart_pl011_is_readable(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- if( (uart_pl011_get_state(dev) == UART_PL011_INITIALIZED) &&
- /* UART is initialized */
- (p_uart->uartcr & UART_PL011_UARTCR_EN_MASK) &&
- /* UART is enabled */
- (p_uart->uartcr & UART_PL011_UARTCR_RX_EN_MASK) &&
- /* Receive is enabled */
- ((p_uart->uartfr & UART_PL011_UARTFR_RX_FIFO_EMPTY) == 0)) {
- /* Receive Fifo is not empty */
- return true;
- }
-
- return false;
-
-}
-
-enum uart_pl011_error_t uart_pl011_read(
- struct uart_pl011_dev_t* dev, uint8_t* byte)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- *byte = p_uart->uartdr;
-
- return (enum uart_pl011_error_t)(p_uart->uartrsr
- & UART_PL011_RX_ERR_MASK);
-}
-
-bool uart_pl011_is_writable(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- if( (uart_pl011_get_state(dev) == UART_PL011_INITIALIZED) &&
- /* UART is initialized */
- (p_uart->uartcr & UART_PL011_UARTCR_EN_MASK) &&
- /* UART is enabled */
- (p_uart->uartcr & UART_PL011_UARTCR_TX_EN_MASK) &&
- /* Transmit is enabled */
- ((p_uart->uartfr & UART_PL011_UARTFR_TX_FIFO_FULL) == 0)) {
- /* Transmit Fifo is not full */
- return true;
- }
- return false;
-
-}
-
-void uart_pl011_write(struct uart_pl011_dev_t* dev, uint8_t byte)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- p_uart->uartdr = byte;
-
- return;
-}
-
-enum uart_pl011_error_t uart_pl011_set_format(struct uart_pl011_dev_t* dev,
- enum uart_pl011_wlen_t word_len,
- enum uart_pl011_parity_t parity,
- enum uart_pl011_stopbit_t stop_bits)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- bool uart_enabled = _uart_pl011_is_enabled(p_uart);
-
- if(uart_pl011_get_state(dev) != UART_PL011_INITIALIZED) {
- return UART_PL011_ERR_NOT_INIT;
- }
-
- /* UART must be disabled before any Control Register or
- * Line Control Register are reprogrammed */
- _uart_pl011_disable(p_uart);
-
- _uart_pl011_set_format(p_uart, word_len, parity, stop_bits);
-
- /* Enabling the UART if previously enabled */
- if(uart_enabled) {
- _uart_pl011_enable(p_uart);
- }
-
- return UART_PL011_ERR_NONE;
-}
-
-void uart_pl011_enable_fifo(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_lcr_h_bit(p_uart, UART_PL011_UARTLCR_H_FEN_MASK);
-
- return;
-}
-
-void uart_pl011_disable_fifo(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_lcr_h_bit(p_uart, UART_PL011_UARTLCR_H_FEN_MASK);
-
- return;
-}
-
-void uart_pl011_enable_break(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_lcr_h_bit(p_uart, UART_PL011_UARTLCR_H_BRK_MASK);
-
- return;
-}
-
-void uart_pl011_disable_break(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_lcr_h_bit(p_uart, UART_PL011_UARTLCR_H_BRK_MASK);
-
- return;
-}
-
-void uart_pl011_enable_cts_flowcontrol(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_CTSE_MASK);
-
- return;
-}
-
-void uart_pl011_disable_cts_flowcontrol(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_CTSE_MASK);
-
- return;
-}
-
-void uart_pl011_enable_rts_flowcontrol(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_RTSE_MASK);
-
- return;
-}
-
-void uart_pl011_disable_rts_flowcontrol(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_RTSE_MASK);
-
- return;
-}
-
-void uart_pl011_enable_ri(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_OUT2_MASK);
-
- return;
-}
-
-void uart_pl011_disable_ri(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_OUT2_MASK);
-
- return;
-}
-
-void uart_pl011_enable_dcd(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_OUT1_MASK);
-
- return;
-}
-
-void uart_pl011_disable_dcd(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_OUT1_MASK);
-
- return;
-}
-
-void uart_pl011_set_rts(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_RTS_MASK);
-
- return;
-}
-
-void uart_pl011_clear_rts(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_RTS_MASK);
-
- return;
-}
-
-void uart_pl011_set_dtr(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_DTR_MASK);
-
- return;
-}
-
-void uart_pl011_clear_dtr(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_DTR_MASK);
-
- return;
-}
-
-void uart_pl011_enable_receive(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_RX_EN_MASK);
-
- return;
-}
-
-void uart_pl011_disable_receive(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_RX_EN_MASK);
-
- return;
-}
-
-void uart_pl011_enable_transmit(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_TX_EN_MASK);
-
- return;
-}
-
-void uart_pl011_disable_transmit(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_TX_EN_MASK);
-
- return;
-}
-
-void uart_pl011_set_loopback(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_LBE_MASK);
-
- return;
-}
-
-void uart_pl011_clear_loopback(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_LBE_MASK);
-
- return;
-}
-
-void uart_pl011_enable_sirlp(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart,
- UART_PL011_UARTCR_SIREN_MASK | UART_PL011_UARTCR_SIRLP_MASK);
-
- return;
-}
-
-void uart_pl011_disable_sirlp(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart,
- UART_PL011_UARTCR_SIREN_MASK | UART_PL011_UARTCR_SIRLP_MASK);
-
- return;
-}
-
-void uart_pl011_enable_sir(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_set_cr_bit(p_uart, UART_PL011_UARTCR_SIREN_MASK);
-
- return;
-}
-
-void uart_pl011_disable_sir(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_clear_cr_bit(p_uart, UART_PL011_UARTCR_SIREN_MASK);
-
- return;
-}
-
-void uart_pl011_enable(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_enable(p_uart);
-
- return;
-}
-
-void uart_pl011_disable(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- _uart_pl011_disable(p_uart);
-
- return;
-}
-
-bool uart_pl011_get_cts_status(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
- return (bool)(p_uart->uartfr & UART_PL011_UARTFR_CTS_MASK);
-
-}
-
-bool uart_pl011_get_dsr_status(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
- return (bool)(p_uart->uartfr & UART_PL011_UARTFR_DSR_MASK);
-
-}
-
-bool uart_pl011_get_dcd_status(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
- return (bool)(p_uart->uartfr & UART_PL011_UARTFR_DCD_MASK);
-
-}
-
-bool uart_pl011_get_ri_status(struct uart_pl011_dev_t* dev)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
- return (bool)(p_uart->uartfr & UART_PL011_UARTFR_RI_MASK);
-
-}
-
-enum uart_pl011_error_t uart_pl011_set_sirlp_divisor(
- struct uart_pl011_dev_t* dev, uint32_t value)
-{
- struct _uart_pl011_reg_map_t* p_uart =
- (struct _uart_pl011_reg_map_t*)dev->cfg->base;
-
- uint32_t irlp_baud16_clk;
-
- if(uart_pl011_get_state(dev) != UART_PL011_INITIALIZED) {
- return UART_PL011_ERR_NOT_INIT;
- }
-
- if(value == 0) {
- return UART_PL011_ERR_INVALID_ARG;
- }
-
- irlp_baud16_clk = dev->data->uart_clk/value;
-
- /* Chose the divisor so that 1.42MHz < FIrLPBaud16 < 2.12MHz, that
- * results in a low-power pulse duration of 1.41–2.11μs (three times
- * the period of IrLPBaud16). ARM DDI0183F Pg 3-9 */
- if(irlp_baud16_clk < FREQ_IRLPBAUD16_MIN ||
- irlp_baud16_clk > FREQ_IRLPBAUD16_MAX) {
- return UART_PL011_ERR_INVALID_ARG;
- }
-
- p_uart->uartilpr = value;
-
- return UART_PL011_ERR_NONE;
-}
diff --git a/platform/ext/target/musca_a/Native_Driver/uart_pl011_drv.h b/platform/ext/target/musca_a/Native_Driver/uart_pl011_drv.h
deleted file mode 100644
index dcae737..0000000
--- a/platform/ext/target/musca_a/Native_Driver/uart_pl011_drv.h
+++ /dev/null
@@ -1,852 +0,0 @@
-/*
- * Copyright (c) 2016-2018 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-/**
- * \file uart_pl011_drv.h
- * \brief Driver for ARM UART PL011.
- */
-
-#ifndef __UART_PL011_DRV_H__
-#define __UART_PL011_DRV_H__
-
-#include <stdint.h>
-#include <stdbool.h>
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/**
- * \brief ARM UART PL011 state types
- */
-enum uart_pl011_state_t {
- UART_PL011_UNINITIALIZED = 0x0u,
- UART_PL011_INITIALIZED = 0x1u,
-};
-
-#define UART_PL011_UARTRSR_FE_ERR_OFF 0x0u
- /*!< Receive Status Register Frame Error bit field offset */
-#define UART_PL011_UARTRSR_PE_ERR_OFF 0x1u
- /*!< Receive Status Register Parity Error bit field offset */
-#define UART_PL011_UARTRSR_BE_ERR_OFF 0x2u
- /*!< Receive Status Register Break Error bit field offset */
-#define UART_PL011_UARTRSR_OE_ERR_OFF 0x3u
- /*!< Receive Status Register Overrun Error bit field offset */
-
-#define UART_PL011_RX_ERR_MASK ( \
- 0x1u<<UART_PL011_UARTRSR_FE_ERR_OFF \
- | 0x1u<<UART_PL011_UARTRSR_PE_ERR_OFF \
- | 0x1u<<UART_PL011_UARTRSR_BE_ERR_OFF \
- | 0x1u<<UART_PL011_UARTRSR_OE_ERR_OFF)
- /*!< Receive Status Register Error Mask */
-
-#define UART_PL011_UARTFR_CTS_OFF 0x0u
- /*!< Flag Register Clear to send bit field offset */
-#define UART_PL011_UARTFR_DSR_OFF 0x1u
- /*!< Flag Register Data set ready bit field offset */
-#define UART_PL011_UARTFR_DCD_OFF 0x2u
- /*!< Flag Register Data carrier detect bit field offset */
-#define UART_PL011_UARTFR_BUSYBIT_OFF 0x3u
- /*!< Flag Register Busy bit field offset */
-#define UART_PL011_UARTFR_RX_FIFO_EMPTY_OFF 0x4u
- /*!< Flag Register Receive fifo empty bit field offset */
-#define UART_PL011_UARTFR_TX_FIFO_FULL_OFF 0x5u
- /*!< Flag Register Transmit fifo full bit field offset */
-#define UART_PL011_UARTFR_RX_FIFO_FULL_OFF 0x6u
- /*!< Flag Register Receive fifo full bit field offset */
-#define UART_PL011_UARTFR_TX_FIFO_EMPTY_OFF 0x7u
- /*!< Flag Register Transmit fifo empty bit field offset */
-#define UART_PL011_UARTFR_RI_OFF 0x8u
- /*!< Flag Register Ring indicator bit field offset */
-
-#define UART_PL011_UARTLCR_H_BRK_OFF 0x0u
- /*!< Line Control Register Break bit field offset */
-#define UART_PL011_UARTLCR_H_PEN_OFF 0x1u
- /*!< Line Control Register Parity enable bit field offset */
-#define UART_PL011_UARTLCR_H_EPS_OFF 0x2u
- /*!< Line Control Register Even parity select bit field offset */
-#define UART_PL011_UARTLCR_H_STP2_OFF 0x3u
- /*!< Line Control Register 2 stop bit select bit field offset */
-#define UART_PL011_UARTLCR_H_FEN_OFF 0x4u
- /*!< Line Control Register Fifo enable bit field offset */
-#define UART_PL011_UARTLCR_H_WLEN_OFF 0x5u
- /*!< Line Control Register Word length bit field offset */
-#define UART_PL011_UARTLCR_H_SPS_OFF 0x7u
- /*!< Line Control Register Stick parity select bit field offset */
-
-/**
- * \brief Allowed word length options UART PL011
- */
-enum uart_pl011_wlen_t {
- UART_PL011_WLEN_5 = (0x0u<<UART_PL011_UARTLCR_H_WLEN_OFF),
- UART_PL011_WLEN_6 = (0x1u<<UART_PL011_UARTLCR_H_WLEN_OFF),
- UART_PL011_WLEN_7 = (0x2u<<UART_PL011_UARTLCR_H_WLEN_OFF),
- UART_PL011_WLEN_8 = (0x3u<<UART_PL011_UARTLCR_H_WLEN_OFF),
-};
-
-/**
- * \brief Allowed parity options UART PL011
- */
-enum uart_pl011_parity_t {
- UART_PL011_PARITY_DISABLED = (0x0u<<UART_PL011_UARTLCR_H_PEN_OFF),
- UART_PL011_PARITY_ODD = (0x1u<<UART_PL011_UARTLCR_H_PEN_OFF
- | 0x0u<<UART_PL011_UARTLCR_H_EPS_OFF
- | 0x0u<<UART_PL011_UARTLCR_H_SPS_OFF),
- UART_PL011_PARITY_EVEN = (0x1u<<UART_PL011_UARTLCR_H_PEN_OFF
- | 0x1u<<UART_PL011_UARTLCR_H_EPS_OFF
- | 0x0u<<UART_PL011_UARTLCR_H_SPS_OFF),
- UART_PL011_PARITY_STICKY_ONE= (0x1u<<UART_PL011_UARTLCR_H_PEN_OFF
- | 0x0u<<UART_PL011_UARTLCR_H_EPS_OFF
- | 0x1u<<UART_PL011_UARTLCR_H_SPS_OFF),
- UART_PL011_PARITY_STICKY_ZERO= (0x1u<<UART_PL011_UARTLCR_H_PEN_OFF
- | 0x1u<<UART_PL011_UARTLCR_H_EPS_OFF
- | 0x1u<<UART_PL011_UARTLCR_H_SPS_OFF),
-};
-
-/**
- * \brief Allowed stop bits options UART PL011
- */
-enum uart_pl011_stopbit_t {
- UART_PL011_STOPBIT_1 = (0x0u<<UART_PL011_UARTLCR_H_STP2_OFF),
- UART_PL011_STOPBIT_2 = (0x1u<<UART_PL011_UARTLCR_H_STP2_OFF),
-};
-
-#define UART_PL011_UARTCR_UARTEN_OFF 0x0u
- /*!< Control Register Uart enable bit field offset */
-#define UART_PL011_UARTCR_SIREN_OFF 0x1u
- /*!< Control Register Sir enable bit field offset */
-#define UART_PL011_UARTCR_SIRLP_OFF 0x2u
- /*!< Control Register Sir low power bit field offset */
-#define UART_PL011_UARTCR_LBE_OFF 0x7u
- /*!< Control Register Loop back enable bit field offset */
-#define UART_PL011_UARTCR_TXE_OFF 0x8u
- /*!< Control Register Transmit enable bit field offset */
-#define UART_PL011_UARTCR_RXE_OFF 0x9u
- /*!< Control Register Receive enable bit field offset */
-#define UART_PL011_UARTCR_DTR_OFF 0xAu
- /*!< Control Register Data transmit ready bit field offset */
-#define UART_PL011_UARTCR_RTS_OFF 0xBu
- /*!< Control Register Request to send bit field offset */
-#define UART_PL011_UARTCR_OUT1_OFF 0xCu
- /*!< Control Register Out1 bit field offset */
-#define UART_PL011_UARTCR_OUT2_OFF 0xDu
- /*!< Control Register Out2 bit field offset */
-#define UART_PL011_UARTCR_RTSE_OFF 0xEu
- /*!< Control Register RTS hardware flow control enable bit field offset */
-#define UART_PL011_UARTCR_CTSE_OFF 0xFu
- /*!< Control Register CTS hardware flow control enable bit field offset */
-
-#define UART_PL011_UARTIFLS_TX_OFF 0x0u
- /*!< Interrupt FIFO Level Select Register Transmit bit field offset */
-#define UART_PL011_UARTIFLS_RX_OFF 0x3u
- /*!< Interrupt FIFO Level Select Register Receive bit field offset */
-
-/**
- * \brief UART Receive fifo levels
- */
-enum uart_pl011_rx_fifo_lvl_t {
- UART_PL011_RX_FIFO_LVL_1_8 = (0x0u<<UART_PL011_UARTIFLS_RX_OFF),
- UART_PL011_RX_FIFO_LVL_1_4 = (0x1u<<UART_PL011_UARTIFLS_RX_OFF),
- UART_PL011_RX_FIFO_LVL_1_2 = (0x2u<<UART_PL011_UARTIFLS_RX_OFF),
- UART_PL011_RX_FIFO_LVL_3_4 = (0x3u<<UART_PL011_UARTIFLS_RX_OFF),
- UART_PL011_RX_FIFO_LVL_7_8 = (0x4u<<UART_PL011_UARTIFLS_RX_OFF),
-};
-
-/**
- * \brief UART Transmit fifo levels
- */
-enum uart_pl011_tx_fifo_lvl_t {
- UART_PL011_TX_FIFO_LVL_1_8 = (0x0u<<UART_PL011_UARTIFLS_TX_OFF),
- UART_PL011_TX_FIFO_LVL_1_4 = (0x1u<<UART_PL011_UARTIFLS_TX_OFF),
- UART_PL011_TX_FIFO_LVL_1_2 = (0x2u<<UART_PL011_UARTIFLS_TX_OFF),
- UART_PL011_TX_FIFO_LVL_3_4 = (0x3u<<UART_PL011_UARTIFLS_TX_OFF),
- UART_PL011_TX_FIFO_LVL_7_8 = (0x4u<<UART_PL011_UARTIFLS_TX_OFF),
-};
-
-#define UART_PL011_UARTDMACR_RXEN_OFF 0x0u
- /*!< DMA Control Register Receive DMA enable bit field offset */
-#define UART_PL011_UARTDMACR_TXEN_OFF 0x1u
- /*!< DMA Control Register Transmit DMA enable bit field offset */
-#define UART_PL011_UARTDMACR_ON_ERR_OFF 0x2u
- /*!< DMA Control Register DMA on error bit field offset */
-
-/**
- * \brief Transmit DMA Enable
- */
-enum uart_pl011_tx_dma_t {
- UART_PL011_TX_DMA_DISABLE = (0x0u<<UART_PL011_UARTDMACR_TXEN_OFF),
- UART_PL011_TX_DMA_ENABLE = (0x1u<<UART_PL011_UARTDMACR_TXEN_OFF),
-};
-
-/**
- * \brief Receive DMA Enable
- */
-enum uart_pl011_rx_dma_t {
- UART_PL011_RX_DMA_DISABLE = (0x0u<<UART_PL011_UARTDMACR_RXEN_OFF),
- UART_PL011_RX_DMA_ENABLE = (0x1u<<UART_PL011_UARTDMACR_RXEN_OFF),
- UART_PL011_RX_DMA_ON_ERR_EN= (0x1u<<UART_PL011_UARTDMACR_RXEN_OFF
- | 0x1u<<UART_PL011_UARTDMACR_ON_ERR_OFF),
-};
-
-#define UART_PL011_INTR_RI_OFF 0x0u
- /*!< Ring indicator interrupt bit field offset */
-#define UART_PL011_INTR_CTS_OFF 0x1u
- /*!< Clear to send interrupt bit field offset */
-#define UART_PL011_INTR_DCD_OFF 0x2u
- /*!< Data carrier detect interrupt bit field offset */
-#define UART_PL011_INTR_DSR_OFF 0x3u
- /*!< Data set ready interrupt bit field offset */
-#define UART_PL011_INTR_RX_OFF 0x4u
- /*!< Receive interrupt bit field offset */
-#define UART_PL011_INTR_TX_OFF 0x5u
- /*!< Transmit interrupt bit field offset */
-#define UART_PL011_INTR_RT_OFF 0x6u
- /*!< Receive timeout interrupt bit field offset */
-#define UART_PL011_INTR_FE_OFF 0x7u
- /*!< Frame error interrupt bit field offset */
-#define UART_PL011_INTR_PE_OFF 0x8u
- /*!< Parity error interrupt bit field offset */
-#define UART_PL011_INTR_BE_OFF 0x9u
- /*!< Break error interrupt bit field offset */
-#define UART_PL011_INTR_OE_OFF 0xAu
- /*!< Overrun error interrupt bit field offset */
-
-/**
- * \brief ARM UART PL011 Interrupt data structure
- */
-enum uart_pl011_intr_t {
- UART_PL011_RI_INTR_MASK = (0x1u<<UART_PL011_INTR_RI_OFF),
- UART_PL011_CTS_INTR_MASK = (0x1u<<UART_PL011_INTR_CTS_OFF),
- UART_PL011_DCD_INTR_MASK = (0x1u<<UART_PL011_INTR_DCD_OFF),
- UART_PL011_DSR_INTR_MASK = (0x1u<<UART_PL011_INTR_DSR_OFF),
- UART_PL011_RX_INTR_MASK = (0x1u<<UART_PL011_INTR_RX_OFF),
- UART_PL011_TX_INTR_MASK = (0x1u<<UART_PL011_INTR_TX_OFF),
- UART_PL011_RT_INTR_MASK = (0x1u<<UART_PL011_INTR_RT_OFF),
- UART_PL011_FE_INTR_MASK = (0x1u<<UART_PL011_INTR_FE_OFF),
- UART_PL011_PE_INTR_MASK = (0x1u<<UART_PL011_INTR_PE_OFF),
- UART_PL011_BE_INTR_MASK = (0x1u<<UART_PL011_INTR_BE_OFF),
- UART_PL011_OE_INTR_MASK = (0x1u<<UART_PL011_INTR_OE_OFF),
-};
-
-/**
- * \brief ARM UART PL011 error enumeration types
- */
-enum uart_pl011_error_t {
- UART_PL011_ERR_NONE = (0x0u),
- UART_PL011_ERR_RX_FRAME = (0x1u<<UART_PL011_UARTRSR_FE_ERR_OFF),
- UART_PL011_ERR_RX_PARITY = (0x1u<<UART_PL011_UARTRSR_PE_ERR_OFF),
- UART_PL011_ERR_RX_BREAK = (0x1u<<UART_PL011_UARTRSR_BE_ERR_OFF),
- UART_PL011_ERR_RX_OVERFLOW = (0x1u<<UART_PL011_UARTRSR_OE_ERR_OFF),
- UART_PL011_ERR_INVALID_ARG = (UART_PL011_RX_ERR_MASK + 1),
- UART_PL011_ERR_NOT_READY,
- UART_PL011_ERR_INVALID_BAUD,
- UART_PL011_ERR_NOT_INIT,
-};
-
-/**
- * \brief ARM UART PL011 device configuration structure
- */
-struct uart_pl011_dev_cfg_t {
- const uint32_t base; /*!< UART PL011 base address */
- const uint32_t def_baudrate; /*!< Default baudrate */
- const enum uart_pl011_wlen_t def_wlen; /*!< Default word length */
- const enum uart_pl011_parity_t def_parity; /*!< Default parity */
- const enum uart_pl011_stopbit_t def_stopbit; /*!< Default stop bits */
-};
-
-/**
- * \brief ARM UART PL011 device data structure
- */
-struct uart_pl011_dev_data_t {
- enum uart_pl011_state_t state; /*!< UART State */
- uint32_t uart_clk; /*!< UART clock */
- uint32_t baudrate; /*!< Baudrate */
-};
-
-/**
- * \brief ARM UART PL011 device structure
- */
-struct uart_pl011_dev_t {
- const struct uart_pl011_dev_cfg_t* const cfg;
- /*!< UART PL011 configuration */
- struct uart_pl011_dev_data_t* const data;
- /*!< UART PL011 data */
-};
-
-/**
- * \brief Initializes UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- * \param[in] uart_clk UART clock used by the device.
- *
- * It uses the default baudrate to configure UART.
- *
- * \return Returns error code as specified in \ref uart_pl011_error_t
- *
- * \note This API should be called before calling any of the below UART APIs.
- * \note This function doesn't check if dev is NULL.
- */
-enum uart_pl011_error_t uart_pl011_init(struct uart_pl011_dev_t* dev,
- uint32_t uart_clk);
-
-/**
- * \brief Uninitializes UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_uninit(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Returns the UART PL011 operational state.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \return Returns the UART operational state
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum uart_pl011_state_t uart_pl011_get_state(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Sets the UART baudrate.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] baudrate New baudrate.
- *
- * \return Returns error code as specified in \ref uart_pl011_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum uart_pl011_error_t uart_pl011_set_baudrate(
- struct uart_pl011_dev_t* dev, uint32_t baudrate);
-
-/**
- * \brief Gets the UART baudrate.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \return Returns the UART baudrate.
- *
- * \note The UART should be in valid state before calling this API
- * \ref uart_pl011_get_state should return UART_PL011_INITIALIZED
- * \note This function doesn't check if dev is NULL.
- */
-uint32_t uart_pl011_get_baudrate(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables UART interrupts
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] mask Bit mask for enabling/disabling interrupts
- * \ref uart_pl011_intr_t
- *
- * \note User is responsible to configure the interrupt vector and
- * the interrupt controller.
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_enable_intr(struct uart_pl011_dev_t* dev,
- enum uart_pl011_intr_t mask);
-
-/**
- * \brief Disables UART interrupts
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] mask Bit mask for enabling/disabling interrupts
- * \ref uart_pl011_intr_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_disable_intr(struct uart_pl011_dev_t* dev,
- enum uart_pl011_intr_t mask);
-
-/**
- * \brief Clears UART Interrupt
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] mask Bit mask for clearing interrupts \ref uart_pl011_intr_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_clear_intr(struct uart_pl011_dev_t* dev,
- enum uart_pl011_intr_t mask);
-
-/**
- * \brief Returns the UART Masked interrupt status
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \return Masked interrupt status \ref uart_pl011_intr_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum uart_pl011_intr_t uart_pl011_get_masked_intr_status(
- struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Returns the UART Raw interrupt status
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \return Raw interrupt status \ref uart_pl011_intr_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum uart_pl011_intr_t uart_pl011_get_raw_intr_status(
- struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Sets receive fifo levels
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] rx_lvl Receive fifo levels \ref uart_pl011_rx_fifo_lvl_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_set_rx_fifo_lvl(struct uart_pl011_dev_t* dev,
- enum uart_pl011_rx_fifo_lvl_t rx_lvl);
-
-/**
- * \brief Sets transmit fifo levels
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] tx_lvl Transmit fifo levels \ref uart_pl011_tx_fifo_lvl_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_set_tx_fifo_lvl(struct uart_pl011_dev_t* dev,
- enum uart_pl011_tx_fifo_lvl_t tx_lvl);
-
-/**
- * \brief Enables/Disables transmit UART DMA
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] enable To enable/disable the UART transmit DMA
- * \ref uart_pl011_tx_dma_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_set_tx_dma(struct uart_pl011_dev_t* dev,
- enum uart_pl011_tx_dma_t enable);
-
-/**
- * \brief Enables/Disables receive UART DMA
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] enable To enable/disable the UART receive DMA
- * \ref uart_pl011_rx_dma_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_set_rx_dma(struct uart_pl011_dev_t* dev,
- enum uart_pl011_rx_dma_t enable);
-
-/**
- * \brief Check if the UART dev is readable
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \return Returns bool, true if UART is readable, false otherwise
- *
- * \note This function doesn't check if dev is NULL.
- */
-bool uart_pl011_is_readable(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Reads one byte from UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[out] byte Pointer to byte that is populated with the data to be read
- *
- * \return Error status (if any) as specified in
- * \ref uart_pl011_error_t
- *
- * \note This API should only be called when the device is readable
- * \ref uart_pl011_is_readable
- * \note For better performance, this function doesn't check if dev and byte
- * pointer are NULL, and if the driver is initialized.
- */
-enum uart_pl011_error_t uart_pl011_read(struct uart_pl011_dev_t* dev,
- uint8_t* byte);
-
-/**
- * \brief Check if the UART dev is writable
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \return Returns bool, true if UART is writable, false otherwise
- *
- * \note This function doesn't check if dev is NULL.
- */
-bool uart_pl011_is_writable(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Writes a byte to UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] byte One byte to write.
- *
- * \note This API should only be called when the device is writable
- * \ref uart_pl011_is_writable
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_write(struct uart_pl011_dev_t* dev, uint8_t byte);
-
-/**
- * \brief Sets the UART format.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] word_len UART word length \ref uart_pl011_wlen_t
- * \param[in] parity UART parity \ref uart_pl011_parity_t
- * \param[in] stop_bits UART stop bits \ref uart_pl011_stopbit_t
- *
- * \return Returns error code as specified in \ref uart_pl011_error_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-enum uart_pl011_error_t uart_pl011_set_format(struct uart_pl011_dev_t* dev,
- enum uart_pl011_wlen_t word_len,
- enum uart_pl011_parity_t parity,
- enum uart_pl011_stopbit_t stop_bits);
-
-/**
- * \brief Enables the UART fifo.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_enable_fifo(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables the UART fifo.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_disable_fifo(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables break transmission from UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_enable_break(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables break transmission from UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_disable_break(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables CTS flow control in UART PL011
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_enable_cts_flowcontrol(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables CTS flow control in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_disable_cts_flowcontrol(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables RTS flow control in UART PL011
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_enable_rts_flowcontrol(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables RTS flow control in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_disable_rts_flowcontrol(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables Data carrier detect in UART PL011
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \note For DTE nUARTOut1 can be used as Data carrier detect (DCD).
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_enable_dcd(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables Data carrier detect in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \note For DTE nUARTOut1 can be used as Data carrier detect (DCD).
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_disable_dcd(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables RTS signal for UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_set_rts(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables RTS signal for UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_clear_rts(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables DTR signal for UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_set_dtr(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables DTR signal for UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_clear_dtr(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables reception in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_enable_receive(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables reception in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_disable_receive(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables transmission in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_enable_transmit(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables transmission in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_disable_transmit(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables loopback in UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_set_loopback(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables loopback in UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_clear_loopback(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables IrDA Sir low power mode in UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_enable_sirlp(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables IrDA Sir in UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_disable_sirlp(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables IrDA Sir in UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_enable_sir(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables IrDA Sir in UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- *
- * \note For better performance, this function doesn't check if dev is NULL and
- * if the driver is initialized to have better performance.
- */
-void uart_pl011_disable_sir(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Enables in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_enable(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Disables in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- *
- * \note This function doesn't check if dev is NULL.
- */
-void uart_pl011_disable(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Gets the Clear to send status in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \return Returns bool, true when the modem status input is 0, false otherwise
- *
- * \note This bit is the complement of the UART clear to send (nUARTCTS) modem
- * status input.
- * \note This function doesn't check if dev is NULL.
- */
-bool uart_pl011_get_cts_status(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Gets the Data set ready status in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \return Returns bool, true when the modem status input is 0, false otherwise
- *
- * \note This bit is the complement of the UART UART data set ready (nUARTDSR)
- * modem status input.
- * \note This function doesn't check if dev is NULL.
- */
-bool uart_pl011_get_dsr_status(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Gets the Data carrier detect status in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \return Returns bool, true when the modem status input is 0, false otherwise
- *
- * \note This bit is the complement of the UART data carrier detect (nUARTDCD)
- * modem status input.
- * \note This function doesn't check if dev is NULL.
- */
-bool uart_pl011_get_dcd_status(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Gets the Ring indicator status in UART PL011.
- *
- * \param[in] dev UART PL011 device struct \ref uart_pl011_dev_t
- *
- * \return Returns bool, true when the modem status input is 0, false otherwise
- *
- * \note This bit is the complement of the UART ring indicator (nUARTRI) modem
- * status input.
- * \note This function doesn't check if dev is NULL.
- */
-bool uart_pl011_get_ri_status(struct uart_pl011_dev_t* dev);
-
-/**
- * \brief Sets the Low power Divisor in UART dev.
- *
- * \param[in] dev UART device struct \ref uart_pl011_dev_t
- * \param[in] value Low power divisor value to be set
- *
- * \return Returns error code as specified in \ref uart_pl011_error_t
- *
- * \note For better performance, this function doesn't check if dev is NULL
- */
-enum uart_pl011_error_t uart_pl011_set_sirlp_divisor(
- struct uart_pl011_dev_t* dev, uint32_t value);
-
-#ifdef __cplusplus
-}
-#endif
-#endif /* __UART_PL011_DRV_H__ */
diff --git a/platform/ext/target/musca_a/boot_hal.c b/platform/ext/target/musca_a/boot_hal.c
deleted file mode 100644
index 9e93972..0000000
--- a/platform/ext/target/musca_a/boot_hal.c
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * Copyright (c) 2019-2020, Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#include "cmsis.h"
-#include "region.h"
-#include "target_cfg.h"
-#include "boot_hal.h"
-#include "Driver_Flash.h"
-#include "flash_layout.h"
-
-/* Flash device name must be specified by target */
-extern ARM_DRIVER_FLASH FLASH_DEV_NAME;
-
-REGION_DECLARE(Image$$, ER_DATA, $$Base)[];
-REGION_DECLARE(Image$$, ARM_LIB_HEAP, $$ZI$$Limit)[];
-REGION_DECLARE(Image$$, ARM_LIB_STACK, $$ZI$$Base);
-
-__attribute__((naked)) void boot_clear_bl2_ram_area(void)
-{
- __ASM volatile(
- "mov r0, #0 \n"
- "subs %1, %1, %0 \n"
- "Loop: \n"
- "subs %1, #4 \n"
- "itt ge \n"
- "strge r0, [%0, %1] \n"
- "bge Loop \n"
- "bx lr \n"
- :
- : "r" (REGION_NAME(Image$$, ER_DATA, $$Base)),
- "r" (REGION_NAME(Image$$, ARM_LIB_HEAP, $$ZI$$Limit))
- : "r0", "memory"
- );
-}
-
-int32_t boot_platform_init(void)
-{
- int32_t result;
-
- /* Initialize stack limit register */
- uint32_t msp_stack_bottom =
- (uint32_t)®ION_NAME(Image$$, ARM_LIB_STACK, $$ZI$$Base);
-
- __set_MSPLIM(msp_stack_bottom);
-
- result = FLASH_DEV_NAME.Initialize(NULL);
- if (result != ARM_DRIVER_OK) {
- return 1;
- }
-
- return 0;
-}
-
-void boot_platform_quit(struct boot_arm_vector_table *vt)
-{
- /* Clang at O0, stores variables on the stack with SP relative addressing.
- * When manually set the SP then the place of reset vector is lost.
- * Static variables are stored in 'data' or 'bss' section, change of SP has
- * no effect on them.
- */
- static struct boot_arm_vector_table *vt_cpy;
- int32_t result;
-
- result = FLASH_DEV_NAME.Uninitialize();
- if (result != ARM_DRIVER_OK) {
- while (1);
- }
-
- vt_cpy = vt;
-
- __set_MSPLIM(0);
- __set_MSP(vt->msp);
- __DSB();
- __ISB();
-
- boot_jump_to_next_image(vt_cpy->reset);
-}
-
diff --git a/platform/ext/target/musca_a/config.cmake b/platform/ext/target/musca_a/config.cmake
deleted file mode 100644
index dd4e878..0000000
--- a/platform/ext/target/musca_a/config.cmake
+++ /dev/null
@@ -1,10 +0,0 @@
-#-------------------------------------------------------------------------------
-# Copyright (c) 2020, Arm Limited. All rights reserved.
-#
-# SPDX-License-Identifier: BSD-3-Clause
-#
-#-------------------------------------------------------------------------------
-
-set(MCUBOOT_UPGRADE_STRATEGY "RAM_LOAD" CACHE STRING "Upgrade strategy when multiple boot images are loaded [OVERWRITE_ONLY, SWAP, DIRECT_XIP, RAM_LOAD]")
-set(MCUBOOT_IMAGE_NUMBER 1 CACHE STRING "Whether to combine S and NS into either 1 image, or sign each separately")
-set(PS_MAX_ASSET_SIZE "512" CACHE STRING "The maximum asset size to be stored in the Protected Storage area")
diff --git a/platform/ext/target/musca_a/partition/flash_layout.h b/platform/ext/target/musca_a/partition/flash_layout.h
deleted file mode 100644
index b0c7839..0000000
--- a/platform/ext/target/musca_a/partition/flash_layout.h
+++ /dev/null
@@ -1,234 +0,0 @@
-/*
- * Copyright (c) 2018-2021 Arm Limited. All rights reserved.
- * Copyright (c) 2020 Cypress Semiconductor Corporation. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#ifndef __FLASH_LAYOUT_H__
-#define __FLASH_LAYOUT_H__
-
-/* Flash layout on Musca with BL2 (single image boot, mandatory):
- *
- * 0x0020_0000 BL2 - MCUBoot (128 KB)
- * 0x0022_0000 Primary image area (1 MB):
- * 0x0022_0000 Secure image primary
- * 0x002A_0000 Non-secure image primary
- * 0x0032_0000 Secondary image area (1 MB):
- * 0x0032_0000 Secure image secondary
- * 0x003A_0000 Non-secure image secondary
- * 0x0042_0000 Protected Storage Area (8 KB)
- * 0x0042_2000 Internal Trusted Storage Area (8 KB)
- * 0x0042_4000 NV counters area (4 KB)
- * 0x0042_5000 Unused
- */
-
-/* Code SRAM layout on Musca (with BL2, which is mandatory) after the newest
- * image has been copied to SRAM:
- * 0x0000_0000 BL2 - MCUBoot (128 KB)
- * 0x0002_0000 Flash_area_newest_image (1 MB)
- * 0x0002_0000 Secure image primary
- * 0x000A_0000 Non-secure image primary
- * 0x0012_00000 Unused
- */
-
-/* This header file is included from linker scatter file as well, where only a
- * limited C constructs are allowed. Therefore it is not possible to include
- * here the platform_base_address.h to access flash related defines. To resolve
- * this some of the values are redefined here with different names, these are
- * marked with comment.
- */
-
-/* Size of a Secure and of a Non-secure image */
-#define FLASH_S_PARTITION_SIZE (0x80000) /* S partition: 512 KB */
-#define FLASH_NS_PARTITION_SIZE (0x80000) /* NS partition: 512 KB */
-#define FLASH_MAX_PARTITION_SIZE ((FLASH_S_PARTITION_SIZE > \
- FLASH_NS_PARTITION_SIZE) ? \
- FLASH_S_PARTITION_SIZE : \
- FLASH_NS_PARTITION_SIZE)
-
-/* Sector size of the flash hardware */
-#define FLASH_AREA_IMAGE_SECTOR_SIZE (0x1000) /* 4 KB */
-#define FLASH_TOTAL_SIZE (0x800000) /* 8 MB */
-
-/* Flash layout info for BL2 bootloader */
-/* Same as MPC_QSPI_RANGE_BASE_S */
-#define FLASH_BASE_ADDRESS (0x10200000)
-
-/* Offset and size definitions of the flash partitions that are handled by the
- * bootloader. The image swapping is done between IMAGE_PRIMARY and
- * IMAGE_SECONDARY, SCRATCH is used as a temporary storage during image
- * swapping.
- */
-#define FLASH_AREA_BL2_OFFSET (0x0)
-#define FLASH_AREA_BL2_SIZE (0x20000) /* 128KB */
-
-#if !defined(MCUBOOT_IMAGE_NUMBER) || (MCUBOOT_IMAGE_NUMBER == 1)
-/* Secure + Non-secure image primary slot */
-#define FLASH_AREA_0_ID (1)
-#define FLASH_AREA_0_OFFSET (FLASH_AREA_BL2_OFFSET + FLASH_AREA_BL2_SIZE)
-#define FLASH_AREA_0_SIZE (FLASH_S_PARTITION_SIZE + \
- FLASH_NS_PARTITION_SIZE)
-/* Secure + Non-secure secondary slot */
-#define FLASH_AREA_2_ID (FLASH_AREA_0_ID + 1)
-#define FLASH_AREA_2_OFFSET (FLASH_AREA_0_OFFSET + FLASH_AREA_0_SIZE)
-#define FLASH_AREA_2_SIZE (FLASH_S_PARTITION_SIZE + \
- FLASH_NS_PARTITION_SIZE)
-/* Not used, only the RAM loading firmware upgrade operation
- * is supported on Musca-A.
- */
-#define FLASH_AREA_SCRATCH_ID (FLASH_AREA_2_ID + 1)
-#define FLASH_AREA_SCRATCH_OFFSET (FLASH_AREA_2_OFFSET + FLASH_AREA_2_SIZE)
-#define FLASH_AREA_SCRATCH_SIZE (0)
-/* Maximum number of image sectors supported by the bootloader. */
-#define MCUBOOT_MAX_IMG_SECTORS ((FLASH_S_PARTITION_SIZE + \
- FLASH_NS_PARTITION_SIZE) / \
- FLASH_AREA_IMAGE_SECTOR_SIZE)
-#elif (MCUBOOT_IMAGE_NUMBER == 2)
-/* Secure image primary slot */
-#define FLASH_AREA_0_ID (1)
-#define FLASH_AREA_0_OFFSET (FLASH_AREA_BL2_OFFSET + FLASH_AREA_BL2_SIZE)
-#define FLASH_AREA_0_SIZE (FLASH_S_PARTITION_SIZE)
-/* Non-secure image primary slot */
-#define FLASH_AREA_1_ID (FLASH_AREA_0_ID + 1)
-#define FLASH_AREA_1_OFFSET (FLASH_AREA_0_OFFSET + FLASH_AREA_0_SIZE)
-#define FLASH_AREA_1_SIZE (FLASH_NS_PARTITION_SIZE)
-/* Secure image secondary slot */
-#define FLASH_AREA_2_ID (FLASH_AREA_1_ID + 1)
-#define FLASH_AREA_2_OFFSET (FLASH_AREA_1_OFFSET + FLASH_AREA_1_SIZE)
-#define FLASH_AREA_2_SIZE (FLASH_S_PARTITION_SIZE)
-/* Non-secure image secondary slot */
-#define FLASH_AREA_3_ID (FLASH_AREA_2_ID + 1)
-#define FLASH_AREA_3_OFFSET (FLASH_AREA_2_OFFSET + FLASH_AREA_2_SIZE)
-#define FLASH_AREA_3_SIZE (FLASH_NS_PARTITION_SIZE)
-/* Not used, only the RAM loading firmware upgrade operation
- * is supported on Musca-A.
- */
-#define FLASH_AREA_SCRATCH_ID (FLASH_AREA_3_ID + 1)
-#define FLASH_AREA_SCRATCH_OFFSET (FLASH_AREA_3_OFFSET + FLASH_AREA_3_SIZE)
-#define FLASH_AREA_SCRATCH_SIZE (0)
-/* Maximum number of image sectors supported by the bootloader. */
-#define MCUBOOT_MAX_IMG_SECTORS (FLASH_MAX_PARTITION_SIZE / \
- FLASH_AREA_IMAGE_SECTOR_SIZE)
-#else /* MCUBOOT_IMAGE_NUMBER > 2 */
-#error "Only MCUBOOT_IMAGE_NUMBER 1 and 2 are supported!"
-#endif /* MCUBOOT_IMAGE_NUMBER */
-
-/* Not used, only the RAM loading firmware upgrade operation
- * is supported on Musca-A. The maximum number of status entries
- * supported by the bootloader.
- */
-#define MCUBOOT_STATUS_MAX_ENTRIES (0)
-
-/* Protected Storage (PS) Service definitions */
-#define FLASH_PS_AREA_OFFSET (FLASH_AREA_SCRATCH_OFFSET + \
- FLASH_AREA_SCRATCH_SIZE)
-#define FLASH_PS_AREA_SIZE (0x2000) /* 8 KB */
-
-/* Internal Trusted Storage (ITS) Service definitions */
-#define FLASH_ITS_AREA_OFFSET (FLASH_PS_AREA_OFFSET + \
- FLASH_PS_AREA_SIZE)
-#define FLASH_ITS_AREA_SIZE (0x2000) /* 8 KB */
-
-/* NV Counters definitions */
-#define FLASH_NV_COUNTERS_AREA_OFFSET (FLASH_ITS_AREA_OFFSET + \
- FLASH_ITS_AREA_SIZE)
-#define FLASH_NV_COUNTERS_AREA_SIZE (FLASH_AREA_IMAGE_SECTOR_SIZE)
-
-/* Offset and size definition in flash area used by assemble.py */
-#define SECURE_IMAGE_OFFSET (0x0)
-#define SECURE_IMAGE_MAX_SIZE FLASH_S_PARTITION_SIZE
-
-#define NON_SECURE_IMAGE_OFFSET (SECURE_IMAGE_OFFSET + \
- SECURE_IMAGE_MAX_SIZE)
-#define NON_SECURE_IMAGE_MAX_SIZE FLASH_NS_PARTITION_SIZE
-
-/* Image load address used by imgtool.py */
-#define IMAGE_LOAD_ADDRESS (S_SRAM_ALIAS_BASE + \
- FLASH_AREA_BL2_SIZE)
-
-/* Define where executable memory for the images starts and ends */
-#define IMAGE_EXECUTABLE_RAM_START (IMAGE_LOAD_ADDRESS)
-#define IMAGE_EXECUTABLE_RAM_SIZE (FLASH_S_PARTITION_SIZE + \
- FLASH_NS_PARTITION_SIZE)
-
-
-#define S_QSPI_ALIAS_BASE (0x10200000)
-#define NS_QSPI_ALIAS_BASE (0x00200000)
-
-#define S_SRAM_ALIAS_BASE (0x10000000)
-#define NS_SRAM_ALIAS_BASE (0x00000000)
-
-/* Flash device name used by BL2
- * Name is defined in flash driver file: Driver_Flash.c
- */
-#define FLASH_DEV_NAME Driver_FLASH0
-
-/* Protected Storage (PS) Service definitions
- * Note: Further documentation of these definitions can be found in the
- * TF-M PS Integration Guide.
- */
-#define TFM_HAL_PS_FLASH_DRIVER Driver_FLASH0
-
-/* In this target the CMSIS driver requires only the offset from the base
- * address instead of the full memory address.
- */
-/* Base address of dedicated flash area for PS */
-#define TFM_HAL_PS_FLASH_AREA_ADDR FLASH_PS_AREA_OFFSET
-/* Size of dedicated flash area for PS */
-#define TFM_HAL_PS_FLASH_AREA_SIZE FLASH_PS_AREA_SIZE
-#define PS_RAM_FS_SIZE TFM_HAL_PS_FLASH_AREA_SIZE
-/* Number of physical erase sectors per logical FS block */
-#define TFM_HAL_PS_SECTORS_PER_BLOCK (1)
-/* Smallest flash programmable unit in bytes */
-#define TFM_HAL_PS_PROGRAM_UNIT (0x1)
-
-/* Internal Trusted Storage (ITS) Service definitions
- * Note: Further documentation of these definitions can be found in the
- * TF-M ITS Integration Guide. The ITS should be in the internal flash, but is
- * allocated in the external flash just for development platforms that don't
- * have internal flash available.
- */
-#define TFM_HAL_ITS_FLASH_DRIVER Driver_FLASH0
-
-/* In this target the CMSIS driver requires only the offset from the base
- * address instead of the full memory address.
- */
-/* Base address of dedicated flash area for ITS */
-#define TFM_HAL_ITS_FLASH_AREA_ADDR FLASH_ITS_AREA_OFFSET
-/* Size of dedicated flash area for ITS */
-#define TFM_HAL_ITS_FLASH_AREA_SIZE FLASH_ITS_AREA_SIZE
-#define ITS_RAM_FS_SIZE TFM_HAL_ITS_FLASH_AREA_SIZE
-/* Number of physical erase sectors per logical FS block */
-#define TFM_HAL_ITS_SECTORS_PER_BLOCK (1)
-/* Smallest flash programmable unit in bytes */
-#define TFM_HAL_ITS_PROGRAM_UNIT (0x1)
-
-/* NV Counters definitions */
-#define TFM_NV_COUNTERS_AREA_ADDR FLASH_NV_COUNTERS_AREA_OFFSET
-#define TFM_NV_COUNTERS_AREA_SIZE (0x18) /* 24 Bytes */
-#define TFM_NV_COUNTERS_SECTOR_ADDR FLASH_NV_COUNTERS_AREA_OFFSET
-#define TFM_NV_COUNTERS_SECTOR_SIZE FLASH_AREA_IMAGE_SECTOR_SIZE
-
-/* Use QSPI Flash memory to store Code data */
-#define S_ROM_ALIAS_BASE (0x10200000)
-#define NS_ROM_ALIAS_BASE (0x00200000)
-
-/* FIXME: Use SRAM2 memory to store RW data */
-#define S_RAM_ALIAS_BASE (0x30000000)
-#define NS_RAM_ALIAS_BASE (0x20000000)
-
-#define TOTAL_ROM_SIZE (0x200000) /* 2 MB */
-#define TOTAL_RAM_SIZE (0x20000) /* 128 KB */
-
-#endif /* __FLASH_LAYOUT_H__ */
diff --git a/platform/ext/target/musca_a/partition/region_defs.h b/platform/ext/target/musca_a/partition/region_defs.h
deleted file mode 100644
index a733abf..0000000
--- a/platform/ext/target/musca_a/partition/region_defs.h
+++ /dev/null
@@ -1,155 +0,0 @@
-/*
- * Copyright (c) 2017-2020 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#ifndef __REGION_DEFS_H__
-#define __REGION_DEFS_H__
-
-#include "flash_layout.h"
-
-#define BL2_HEAP_SIZE (0x0001000)
-#define BL2_MSP_STACK_SIZE (0x0001800)
-
-#define S_HEAP_SIZE (0x0001000)
-#define S_MSP_STACK_SIZE_INIT (0x0000400)
-#define S_MSP_STACK_SIZE (0x0000800)
-#define S_PSP_STACK_SIZE (0x0000800)
-
-#define NS_HEAP_SIZE (0x0001000)
-#define NS_MSP_STACK_SIZE (0x00000A0)
-#define NS_PSP_STACK_SIZE (0x0000140)
-
-/* This size of buffer is big enough to store an attestation
- * token produced by initial attestation service
- */
-#define PSA_INITIAL_ATTEST_TOKEN_MAX_SIZE (0x250)
-
-/* MPC granularity is 128 KB on Musca_A. Alignment
- * of partitions is defined in accordance with this constraint.
- */
-#define S_IMAGE_PRIMARY_PARTITION_OFFSET (FLASH_AREA_0_OFFSET)
-#define S_IMAGE_SECONDARY_PARTITION_OFFSET (FLASH_AREA_2_OFFSET)
-
-#define NS_IMAGE_PRIMARY_PARTITION_OFFSET (FLASH_AREA_0_OFFSET \
- + FLASH_S_PARTITION_SIZE)
-
-/* Boot partition structure if MCUBoot is used:
- * 0x0_0000 Bootloader header
- * 0x0_0400 Image area
- * 0x1_FC00 Trailer
- */
-/* IMAGE_CODE_SIZE is the space available for the software binary image.
- * It is less than the FLASH_S_PARTITION_SIZE + FLASH_NS_PARTITION_SIZE
- * because we reserve space for the image header and trailer introduced
- * by the bootloader.
- */
-#define BL2_HEADER_SIZE (0x400) /* 1 KB */
-#define BL2_TRAILER_SIZE (0x400) /* 1 KB */
-
-#define IMAGE_S_CODE_SIZE \
- (FLASH_S_PARTITION_SIZE - BL2_HEADER_SIZE - BL2_TRAILER_SIZE)
-#define IMAGE_NS_CODE_SIZE \
- (FLASH_NS_PARTITION_SIZE - BL2_HEADER_SIZE - BL2_TRAILER_SIZE)
-
-#define CMSE_VENEER_REGION_SIZE (0x340)
-
-/* Alias definitions for secure and non-secure areas*/
-#define S_ROM_ALIAS(x) (S_SRAM_ALIAS_BASE + (x))
-#define NS_ROM_ALIAS(x) (NS_SRAM_ALIAS_BASE + (x))
-
-#define S_RAM_ALIAS(x) (S_RAM_ALIAS_BASE + (x))
-#define NS_RAM_ALIAS(x) (NS_RAM_ALIAS_BASE + (x))
-
-/* Secure regions */
-#define S_IMAGE_PRIMARY_AREA_OFFSET \
- (S_IMAGE_PRIMARY_PARTITION_OFFSET + BL2_HEADER_SIZE)
-#define S_CODE_START (S_ROM_ALIAS(S_IMAGE_PRIMARY_AREA_OFFSET))
-#define S_CODE_SIZE (IMAGE_S_CODE_SIZE - CMSE_VENEER_REGION_SIZE)
-#define S_CODE_LIMIT (S_CODE_START + S_CODE_SIZE - 1)
-
-#define S_DATA_START (S_RAM_ALIAS(0x0))
-/* Reserve 96 KB of RAM to the SPE to meet worst case scenario
- * requirements which are encountered in IPC mode and regression
- * tests enabled. Leave the remaining 32 KB to the NSPE.
- */
-#define S_DATA_SIZE ((TOTAL_RAM_SIZE / 4) * 3)
-#define S_DATA_LIMIT (S_DATA_START + S_DATA_SIZE - 1)
-
-/* CMSE Veneers region */
-#define CMSE_VENEER_REGION_START (S_CODE_LIMIT + 1)
-
-/* Non-secure regions */
-#define NS_IMAGE_PRIMARY_AREA_OFFSET \
- (NS_IMAGE_PRIMARY_PARTITION_OFFSET + BL2_HEADER_SIZE)
-#define NS_CODE_START (NS_ROM_ALIAS(NS_IMAGE_PRIMARY_AREA_OFFSET))
-#define NS_CODE_SIZE (IMAGE_NS_CODE_SIZE - FLASH_AREA_BL2_SIZE)
-#define NS_CODE_LIMIT (NS_CODE_START + NS_CODE_SIZE - 1)
-
-#define NS_DATA_START (NS_RAM_ALIAS(S_DATA_SIZE))
-#define NS_DATA_SIZE (TOTAL_RAM_SIZE - S_DATA_SIZE)
-
-#define NS_DATA_LIMIT (NS_DATA_START + NS_DATA_SIZE - 1)
-
-/* NS partition information is used for MPC and SAU configuration */
-#define NS_PARTITION_START \
- (NS_ROM_ALIAS(NS_IMAGE_PRIMARY_PARTITION_OFFSET))
-#define NS_PARTITION_SIZE (FLASH_NS_PARTITION_SIZE)
-
-/* Secondary partition for new images in case of firmware upgrade */
-#define SECONDARY_PARTITION_START \
- (NS_ROM_ALIAS(S_IMAGE_SECONDARY_PARTITION_OFFSET))
-#define SECONDARY_PARTITION_SIZE (FLASH_S_PARTITION_SIZE + \
- FLASH_NS_PARTITION_SIZE)
-
-/* Code SRAM area */
-#define TOTAL_CODE_SRAM_SIZE (TOTAL_ROM_SIZE)
-#define S_CODE_SRAM_ALIAS_BASE (0x10000000)
-#define NS_CODE_SRAM_ALIAS_BASE (0x00000000)
-
-#define BL2_CODE_SRAM_EXEC_BASE (S_CODE_SRAM_ALIAS_BASE)
-#define S_CODE_SRAM_EXEC_BASE (S_CODE_SRAM_ALIAS_BASE)
-#define S_CODE_SRAM_EXEC_LIMIT (S_CODE_SRAM_EXEC_BASE + \
- (TOTAL_CODE_SRAM_SIZE / 2) - 1)
-#define NS_CODE_SRAM_EXEC_BASE (NS_CODE_SRAM_ALIAS_BASE + \
- (TOTAL_CODE_SRAM_SIZE / 2))
-#define NS_CODE_SRAM_EXEC_LIMIT (NS_CODE_SRAM_EXEC_BASE + \
- (TOTAL_CODE_SRAM_SIZE / 2) - 1)
-
-/* Since we enable/disable flash during s/ns code copy to code sram we cannot
- * access bl2 code from flash, hence we need to copy the bl2 code to code sram
- */
-#define BL2_CODE_SRAM_ALIAS_BASE (S_SRAM_ALIAS_BASE)
-#define BL2_CODE_SRAM_ALIAS(x) (BL2_CODE_SRAM_ALIAS_BASE + x)
-#define BL2_CODE_SRAM_BASE (BL2_CODE_SRAM_ALIAS(FLASH_AREA_BL2_OFFSET))
-
-/* Bootloader regions */
-#define BL2_CODE_START (S_QSPI_ALIAS_BASE)
-#define BL2_CODE_SIZE (FLASH_AREA_BL2_SIZE)
-#define BL2_CODE_LIMIT (BL2_CODE_START + BL2_CODE_SIZE - 1)
-
-#define BL2_DATA_START (S_RAM_ALIAS(0x0))
-#define BL2_DATA_SIZE (TOTAL_RAM_SIZE)
-#define BL2_DATA_LIMIT (BL2_DATA_START + BL2_DATA_SIZE - 1)
-
-/* Shared data area between bootloader and runtime firmware.
- * Shared data area is allocated at the beginning of the RAM, it is overlapping
- * with TF-M Secure code's MSP stack
- */
-#define BOOT_TFM_SHARED_DATA_BASE S_RAM_ALIAS_BASE
-#define BOOT_TFM_SHARED_DATA_SIZE (0x400)
-#define BOOT_TFM_SHARED_DATA_LIMIT (BOOT_TFM_SHARED_DATA_BASE + \
- BOOT_TFM_SHARED_DATA_SIZE - 1)
-
-#endif /* __REGION_DEFS_H__ */
diff --git a/platform/ext/target/musca_a/plat_test.c b/platform/ext/target/musca_a/plat_test.c
deleted file mode 100644
index cd6118a..0000000
--- a/platform/ext/target/musca_a/plat_test.c
+++ /dev/null
@@ -1,98 +0,0 @@
-/*
- * Copyright (c) 2019-2021, Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#include "timer_cmsdk_drv.h"
-#include "tfm_plat_defs.h"
-#include "tfm_plat_test.h"
-#include "device_definition.h"
-
-#define USERLED_MASK (0x3)
-#define BTN_WAIT_INIT_COUNTER_VALUE (10000u)
-#define TIMER_RELOAD_VALUE (16*1024*1024)
-
-/**
- * \brief Store the state of the mocked LED
- *
- * This variable have to be linked to the data section of the partition
- * TFM_SP_CORE_TEST so that in case of in case of isolation within the secure
- * domain the Core Test service can access it.
- */
-uint32_t led_status
- TFM_LINK_SET_RW_IN_PARTITION_SECTION("TFM_SP_CORE_TEST", "PSA-ROT")
- = 0x02u;
-
-/**
- * \brief Simulate user reaction time
- */
-static void busy_wait_to_simulate_user(void)
-{
- volatile uint32_t counter = BTN_WAIT_INIT_COUNTER_VALUE;
- while (counter)
- {
- --counter;
- }
-}
-
-void tfm_plat_test_wait_user_button_pressed(void)
-{
- busy_wait_to_simulate_user();
-}
-
-void tfm_plat_test_wait_user_button_released(void)
-{
- busy_wait_to_simulate_user();
-}
-
-uint32_t tfm_plat_test_get_led_status(void)
-{
- return led_status;
-}
-
-void tfm_plat_test_set_led_status(uint32_t status)
-{
- led_status = status & USERLED_MASK;
-}
-
-uint32_t tfm_plat_test_get_userled_mask(void)
-{
- return USERLED_MASK;
-}
-
-
-void tfm_plat_test_secure_timer_start(void)
-{
- if (!timer_cmsdk_is_initialized(&CMSDK_TIMER0_DEV_S)) {
- timer_cmsdk_init(&CMSDK_TIMER0_DEV_S);
- }
- timer_cmsdk_set_reload_value(&CMSDK_TIMER0_DEV_S, TIMER_RELOAD_VALUE);
- timer_cmsdk_enable(&CMSDK_TIMER0_DEV_S);
- timer_cmsdk_enable_interrupt(&CMSDK_TIMER0_DEV_S);
-}
-
-void tfm_plat_test_secure_timer_stop(void)
-{
- timer_cmsdk_disable(&CMSDK_TIMER0_DEV_S);
- timer_cmsdk_disable_interrupt(&CMSDK_TIMER0_DEV_S);
- timer_cmsdk_clear_interrupt(&CMSDK_TIMER0_DEV_S);
-}
-
-void tfm_plat_test_non_secure_timer_start(void)
-{
- if (!timer_cmsdk_is_initialized(&CMSDK_TIMER1_DEV_NS)) {
- timer_cmsdk_init(&CMSDK_TIMER1_DEV_NS);
- }
- timer_cmsdk_set_reload_value(&CMSDK_TIMER1_DEV_NS, TIMER_RELOAD_VALUE);
- timer_cmsdk_enable(&CMSDK_TIMER1_DEV_NS);
- timer_cmsdk_enable_interrupt(&CMSDK_TIMER1_DEV_NS);
-}
-
-void tfm_plat_test_non_secure_timer_stop(void)
-{
- timer_cmsdk_disable(&CMSDK_TIMER1_DEV_NS);
- timer_cmsdk_disable_interrupt(&CMSDK_TIMER1_DEV_NS);
- timer_cmsdk_clear_interrupt(&CMSDK_TIMER1_DEV_NS);
-}
diff --git a/platform/ext/target/musca_a/preload.cmake b/platform/ext/target/musca_a/preload.cmake
deleted file mode 100644
index 436fed7..0000000
--- a/platform/ext/target/musca_a/preload.cmake
+++ /dev/null
@@ -1,16 +0,0 @@
-#-------------------------------------------------------------------------------
-# Copyright (c) 2020, Arm Limited. All rights reserved.
-#
-# SPDX-License-Identifier: BSD-3-Clause
-#
-#-------------------------------------------------------------------------------
-
-# preload.cmake is used to set things that related to the platform that are both
-# immutable and global, which is to say they should apply to any kind of project
-# that uses this platform. In practise this is normally compiler definitions and
-# variables related to hardware.
-
-# Set architecture and CPU
-set(TFM_SYSTEM_PROCESSOR cortex-m33)
-set(TFM_SYSTEM_ARCHITECTURE armv8-m.main)
-set(TFM_SYSTEM_DSP OFF)
diff --git a/platform/ext/target/musca_a/services/include/tfm_ioctl_api.h b/platform/ext/target/musca_a/services/include/tfm_ioctl_api.h
deleted file mode 100644
index f4bbbf3..0000000
--- a/platform/ext/target/musca_a/services/include/tfm_ioctl_api.h
+++ /dev/null
@@ -1,171 +0,0 @@
-/*
- * Copyright (c) 2019, Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#ifndef __TFM_IOCTL_API__
-#define __TFM_IOCTL_API__
-
-#include <limits.h>
-#include <stdint.h>
-#include "tfm_api.h"
-#include "tfm_platform_api.h"
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-enum tfm_platform_ioctl_reqest_types_t {
- TFM_PLATFORM_IOCTL_GPIO_SERVICE,
-};
-
-/*!
- * \enum tfm_gpio_service_type_t
- *
- * \brief GPIO service types (supported types may vary based on the platform)
- */
-enum tfm_gpio_service_type_t {
- TFM_GPIO_SERVICE_TYPE_INIT = 0, /*!< Init */
- TFM_GPIO_SERVICE_TYPE_PIN_CONFIG, /*!< Pin config */
- TFM_GPIO_SERVICE_TYPE_PIN_WRITE, /*!< Pin write */
- TFM_GPIO_SERVICE_TYPE_PIN_READ, /*!< Pin read */
- TFM_GPIO_SERVICE_TYPE_PORT_CONFIG, /*!< Port config */
- TFM_GPIO_SERVICE_TYPE_PORT_WRITE, /*!< Port write */
- TFM_GPIO_SERVICE_TYPE_PORT_READ, /*!< Port read */
- TFM_GPIO_SERVICE_TYPE_MAX = INT_MAX /*!< Max to force enum max size */
-};
-
-/*!
- * \struct tfm_gpio_service_args_t
- *
- * \brief Argument list for each platform GPIO service
- */
-struct tfm_gpio_service_args_t {
- enum tfm_gpio_service_type_t type;
- union {
- struct gpio_config_args { /*!< TFM_GPIO_SERVICE_TYPE_PIN_CONFIG ||
- TFM_GPIO_SERVICE_TYPE_PORT_CONFIG */
- uint32_t pin_num_or_mask;
- uint32_t direction;
- } gpio_config;
- struct gpio_write_args { /*!< TFM_GPIO_SERVICE_TYPE_PIN_WRITE ||
- TFM_GPIO_SERVICE_TYPE_PORT_WRITE */
- uint32_t pin_num_or_mask;
- uint32_t value;
- } gpio_write;
- struct gpio_read_args { /*!< TFM_GPIO_SERVICE_TYPE_PIN_READ ||
- TFM_GPIO_SERVICE_TYPE_PORT_READ */
- uint32_t pin_num_or_mask;
- } gpio_read;
- } u;
-};
-
-/*!
- * \struct tfm_gpio_service_out_t
- *
- * \brief Output list for each GPIO platform service
- */
-struct tfm_gpio_service_out_t {
- union {
- uint32_t result; /*!< Generic result */
- struct gpio_read_result { /*!< TFM_GPIO_SERVICE_TYPE_PIN_READ ||
- TFM_GPIO_SERVICE_TYPE_PORT_READ */
- uint32_t result;
- uint32_t data;
- } gpio_read_result;
- } u;
-};
-
-/*!
- * \brief Initializes GPIO module
- *
- * \param[out] result Return error value
- *
- * \return Returns values as specified by the \ref tfm_platform_err_t
- */
-enum tfm_platform_err_t tfm_platform_gpio_init(uint32_t *result);
-
-/*!
- * \brief Configures a GPIO pin as input or output
- *
- * \param[in] pin_num Pin number of the selected pin
- * \param[in] direction Direction of the pin: 0 for input, 1 for output
- * \param[out] result Return error value
- *
- * \return Returns values as specified by the \ref tfm_platform_err_t
- */
-enum tfm_platform_err_t
-tfm_platform_gpio_pin_config(uint32_t pin_num, uint32_t direction,
- uint32_t *result);
-
-/*!
- * \brief Sets state of a selected GPIO pin
- *
- * \param[in] pin_num Pin number of the selected pin
- * \param[in] value Value to set for the pin
- * \param[out] result Return error value
- *
- * \return Returns values as specified by the \ref tfm_platform_err_t
- */
-enum tfm_platform_err_t
-tfm_platform_gpio_pin_write(uint32_t pin_num, uint32_t value, uint32_t *result);
-
-/*!
- * \brief Reads state of a selected GPIO pin
- *
- * \param[in] pin_num Pin number of the selected pin
- * \param[in,out] data Bit value read from the IO pin
- * \param[out] result Return error value
- *
- * \return Returns values as specified by the \ref tfm_platform_err_t
- */
-enum tfm_platform_err_t
-tfm_platform_gpio_pin_read(uint32_t pin_num, uint32_t *data, uint32_t *result);
-
-/*!
- * \brief Configures GPIO pins as input or output
- *
- * \param[in] pin_mask Pin mask of the selected pins
- * \param[in] direction Direction of the pin: 0 for input, 1 for output
- * \param[out] result Return error value
- *
- * \return Returns values as specified by the \ref tfm_platform_err_t
- */
-enum tfm_platform_err_t
-tfm_platform_gpio_port_config(uint32_t pin_mask, uint32_t direction,
- uint32_t *result);
-
-/*!
- * \brief Sets state of a selected GPIO pins
- *
- * \param[in] pin_mask Pin mask of the selected pins
- * \param[in] value Value mask to set for the pins
- * \param[out] result Return error value
- *
- * \return Returns values as specified by the \ref tfm_platform_err_t
- */
-enum tfm_platform_err_t
-tfm_platform_gpio_port_write(uint32_t pin_mask, uint32_t value,
- uint32_t *result);
-
-/*!
- * \brief Reads state of a selected GPIO pins
- *
- * \param[in] pin_mask Pin mask of the selected pins
- * \param[in,out] data Bit value mask read from the IO pins
- * \param[out] result Return error value
- *
- * \return Returns values as specified by the \ref tfm_platform_err_t
- */
-enum tfm_platform_err_t
-tfm_platform_gpio_port_read(uint32_t pin_mask, uint32_t *data,
- uint32_t *result);
-
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __TFM_IOCTL_API__ */
diff --git a/platform/ext/target/musca_a/services/src/tfm_ioctl_ns_api.c b/platform/ext/target/musca_a/services/src/tfm_ioctl_ns_api.c
deleted file mode 100644
index aaa4a76..0000000
--- a/platform/ext/target/musca_a/services/src/tfm_ioctl_ns_api.c
+++ /dev/null
@@ -1,207 +0,0 @@
-/*
- * Copyright (c) 2019-2020, Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#include <stdint.h>
-#include "tfm_platform_api.h"
-#include "tfm_ioctl_api.h"
-
-enum tfm_platform_err_t tfm_platform_gpio_init(uint32_t *result)
-{
- enum tfm_platform_err_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_INIT;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
-
- return ret;
-}
-
-enum tfm_platform_err_t
-tfm_platform_gpio_pin_config(uint32_t pin_num, uint32_t direction,
- uint32_t *result)
-{
- enum tfm_platform_err_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PIN_CONFIG;
- args.u.gpio_config.pin_num_or_mask = pin_num;
- args.u.gpio_config.direction = direction;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
-
- return ret;
-}
-
-enum tfm_platform_err_t
-tfm_platform_gpio_pin_write(uint32_t pin_num, uint32_t value, uint32_t *result)
-{
- enum tfm_platform_err_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PIN_WRITE;
- args.u.gpio_write.pin_num_or_mask = pin_num;
- args.u.gpio_write.value = value;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
-
- return ret;
-
-}
-
-enum tfm_platform_err_t
-tfm_platform_gpio_pin_read(uint32_t pin_num, uint32_t *data, uint32_t *result)
-{
- enum tfm_platform_err_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PIN_READ;
- args.u.gpio_read.pin_num_or_mask = pin_num;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.gpio_read_result.result;
- *data = out.u.gpio_read_result.data;
- return ret;
-}
-
-enum tfm_platform_err_t
-tfm_platform_gpio_port_config(uint32_t pin_mask, uint32_t direction,
- uint32_t *result)
-{
- enum tfm_platform_err_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PORT_CONFIG;
- args.u.gpio_config.pin_num_or_mask = pin_mask;
- args.u.gpio_config.direction = direction;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
-
- return ret;
-}
-
-enum tfm_platform_err_t
-tfm_platform_gpio_port_write(uint32_t pin_mask, uint32_t value,
- uint32_t *result)
-{
- enum tfm_platform_err_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PORT_WRITE;
- args.u.gpio_write.pin_num_or_mask = pin_mask;
- args.u.gpio_write.value = value;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
-
- return ret;
-
-}
-
-enum tfm_platform_err_t
-tfm_platform_gpio_port_read(uint32_t pin_mask, uint32_t *data, uint32_t *result)
-{
- enum tfm_platform_err_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PORT_READ;
- args.u.gpio_read.pin_num_or_mask = pin_mask;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.gpio_read_result.result;
- *data = out.u.gpio_read_result.data;
- return ret;
-}
-
diff --git a/platform/ext/target/musca_a/services/src/tfm_ioctl_s_api.c b/platform/ext/target/musca_a/services/src/tfm_ioctl_s_api.c
deleted file mode 100644
index 46a5425..0000000
--- a/platform/ext/target/musca_a/services/src/tfm_ioctl_s_api.c
+++ /dev/null
@@ -1,207 +0,0 @@
-/*
- * Copyright (c) 2019-2020, Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#include <stdint.h>
-#include "tfm_platform_api.h"
-#include "tfm_ioctl_api.h"
-
-__attribute__((section("SFN")))
-enum tfm_platform_err_t tfm_platform_gpio_init(uint32_t *result)
-{
- psa_status_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_INIT;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
- return (enum tfm_platform_err_t) ret;
-}
-
-__attribute__((section("SFN")))
-enum tfm_platform_err_t
-tfm_platform_gpio_pin_config(uint32_t pin_num, uint32_t direction,
- uint32_t *result)
-{
- psa_status_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PIN_CONFIG;
- args.u.gpio_config.pin_num_or_mask = pin_num;
- args.u.gpio_config.direction = direction;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
- return (enum tfm_platform_err_t) ret;
-}
-
-__attribute__((section("SFN")))
-enum tfm_platform_err_t
-tfm_platform_gpio_pin_write(uint32_t pin_num, uint32_t value, uint32_t *result)
-{
- psa_status_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PIN_WRITE;
- args.u.gpio_write.pin_num_or_mask = pin_num;
- args.u.gpio_write.value = value;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
- return (enum tfm_platform_err_t) ret;
-}
-
-__attribute__((section("SFN")))
-enum tfm_platform_err_t
-tfm_platform_gpio_pin_read(uint32_t pin_num, uint32_t *data, uint32_t *result)
-{
- psa_status_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PIN_READ;
- args.u.gpio_read.pin_num_or_mask = pin_num;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.gpio_read_result.result;
- *data = out.u.gpio_read_result.data;
- return (enum tfm_platform_err_t) ret;
-}
-
-__attribute__((section("SFN")))
-enum tfm_platform_err_t
-tfm_platform_gpio_port_config(uint32_t pin_mask, uint32_t direction,
- uint32_t *result)
-{
- psa_status_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PORT_CONFIG;
- args.u.gpio_config.pin_num_or_mask = pin_mask;
- args.u.gpio_config.direction = direction;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
- return (enum tfm_platform_err_t) ret;
-}
-
-__attribute__((section("SFN")))
-enum tfm_platform_err_t
-tfm_platform_gpio_port_write(uint32_t pin_mask, uint32_t value,
- uint32_t *result)
-{
- psa_status_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PORT_WRITE;
- args.u.gpio_write.pin_num_or_mask = pin_mask;
- args.u.gpio_write.value = value;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.result;
- return (enum tfm_platform_err_t) ret;
-}
-
-__attribute__((section("SFN")))
-enum tfm_platform_err_t
-tfm_platform_gpio_port_read(uint32_t pin_mask, uint32_t *data, uint32_t *result)
-{
- psa_status_t ret;
- psa_invec in_vec;
- psa_outvec out_vec;
- struct tfm_gpio_service_args_t args;
- struct tfm_gpio_service_out_t out;
-
- args.type = TFM_GPIO_SERVICE_TYPE_PORT_READ;
- args.u.gpio_read.pin_num_or_mask = pin_mask;
-
- in_vec.base = (const void *)&args;
- in_vec.len = sizeof(args);
-
- out_vec.base = (void *)&out;
- out_vec.len = sizeof(out);
-
- ret = tfm_platform_ioctl(TFM_PLATFORM_IOCTL_GPIO_SERVICE,
- &in_vec,
- &out_vec);
-
- *result = out.u.gpio_read_result.result;
- *data = out.u.gpio_read_result.data;
- return (enum tfm_platform_err_t) ret;
-}
-
diff --git a/platform/ext/target/musca_a/services/src/tfm_platform_system.c b/platform/ext/target/musca_a/services/src/tfm_platform_system.c
deleted file mode 100644
index e5c5088..0000000
--- a/platform/ext/target/musca_a/services/src/tfm_platform_system.c
+++ /dev/null
@@ -1,105 +0,0 @@
-/*
- * Copyright (c) 2018-2020, Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#include <stdbool.h>
-#include "tfm_platform_system.h"
-#include "platform_description.h"
-#include "target_cfg.h"
-#include "device_definition.h"
-#include "psa/client.h"
-#include "tfm_ioctl_api.h"
-
-void tfm_platform_hal_system_reset(void)
-{
- /* Reset the system */
- NVIC_SystemReset();
-}
-
-enum tfm_platform_err_t
-tfm_platform_hal_gpio_service(const psa_invec *in_vec,
- const psa_outvec *out_vec)
-{
- struct tfm_gpio_service_args_t *args;
- struct tfm_gpio_service_out_t *out;
- enum gpio_cmsdk_direction_t dir;
- /* Alternate function is configured through the SCC, this is not used
- * on Musca-A, the default value is passed to the driver
- */
- enum gpio_cmsdk_altfunc_t altfunc = GPIO_CMSDK_MAIN_FUNC;
-
- if (in_vec->len != sizeof(struct tfm_gpio_service_args_t) ||
- out_vec->len != sizeof(struct tfm_gpio_service_out_t)) {
- return TFM_PLATFORM_ERR_INVALID_PARAM;
- }
-
- args = (struct tfm_gpio_service_args_t *)in_vec->base;
- out = (struct tfm_gpio_service_out_t *)out_vec->base;
- switch (args->type) {
- case TFM_GPIO_SERVICE_TYPE_INIT:
- gpio_cmsdk_init(&GPIO0_CMSDK_DEV_S);
- out->u.result = GPIO_CMSDK_ERR_NONE;
- break;
- case TFM_GPIO_SERVICE_TYPE_PIN_CONFIG:
- dir = (enum gpio_cmsdk_direction_t)args->u.gpio_config.direction;
- out->u.result = gpio_cmsdk_pin_config(
- &GPIO0_CMSDK_DEV_S,
- args->u.gpio_config.pin_num_or_mask,
- dir, altfunc);
- break;
- case TFM_GPIO_SERVICE_TYPE_PIN_WRITE:
- out->u.result = gpio_cmsdk_pin_write(&GPIO0_CMSDK_DEV_S,
- args->u.gpio_write.pin_num_or_mask,
- args->u.gpio_write.value);
- break;
- case TFM_GPIO_SERVICE_TYPE_PIN_READ:
- out->u.gpio_read_result.result =
- gpio_cmsdk_pin_read(&GPIO0_CMSDK_DEV_S,
- args->u.gpio_read.pin_num_or_mask,
- &out->u.gpio_read_result.data);
- break;
- case TFM_GPIO_SERVICE_TYPE_PORT_CONFIG:
- dir = (enum gpio_cmsdk_direction_t)args->u.gpio_config.direction;
- out->u.result = gpio_cmsdk_port_config(
- &GPIO0_CMSDK_DEV_S,
- args->u.gpio_config.pin_num_or_mask,
- dir, altfunc);
- break;
- case TFM_GPIO_SERVICE_TYPE_PORT_WRITE:
- out->u.result = gpio_cmsdk_port_write(
- &GPIO0_CMSDK_DEV_S,
- args->u.gpio_write.pin_num_or_mask,
- args->u.gpio_write.value);
- break;
- case TFM_GPIO_SERVICE_TYPE_PORT_READ:
- out->u.gpio_read_result.result =
- gpio_cmsdk_port_read(&GPIO0_CMSDK_DEV_S,
- args->u.gpio_read.pin_num_or_mask,
- &out->u.gpio_read_result.data);
- break;
- default:
- out->u.result = GPIO_CMSDK_ERR_INVALID_ARG;
- break;
- }
-
- in_vec++;
- out_vec++;
-
- return TFM_PLATFORM_ERR_SUCCESS;
-}
-
-
-enum tfm_platform_err_t tfm_platform_hal_ioctl(tfm_platform_ioctl_req_t request,
- psa_invec *in_vec,
- psa_outvec *out_vec)
-{
- switch (request){
- case TFM_PLATFORM_IOCTL_GPIO_SERVICE:
- return tfm_platform_hal_gpio_service(in_vec, out_vec);
- default:
- return TFM_PLATFORM_ERR_NOT_SUPPORTED;
- }
-}
diff --git a/platform/ext/target/musca_a/spm_hal.c b/platform/ext/target/musca_a/spm_hal.c
deleted file mode 100644
index 1fb4ed1..0000000
--- a/platform/ext/target/musca_a/spm_hal.c
+++ /dev/null
@@ -1,209 +0,0 @@
-/*
- * Copyright (c) 2018-2021 Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#include <stdio.h>
-#include "cmsis.h"
-#include "tfm_spm_hal.h"
-#include "tfm_platform_core_api.h"
-#include "target_cfg.h"
-#include "Driver_MPC.h"
-#include "mpu_armv8m_drv.h"
-#include "region_defs.h"
-#include "utilities.h"
-#include "tfm_hal_platform.h"
-#include "log/tfm_log.h"
-
-/* Import MPC driver */
-extern ARM_DRIVER_MPC Driver_CODE_SRAM_MPC;
-
-/* Get address of memory regions to configure MPU */
-extern const struct memory_region_limits memory_regions;
-
-struct mpu_armv8m_dev_t dev_mpu_s = { MPU_BASE };
-
-#ifdef CONFIG_TFM_ENABLE_MEMORY_PROTECT
-#define PARTITION_REGION_PERIPH_START 5
-#define PARTITION_REGION_PERIPH_MAX_NUM 2
-
-uint32_t periph_num_count = 0;
-#endif /* CONFIG_TFM_ENABLE_MEMORY_PROTECT */
-
-enum tfm_plat_err_t tfm_spm_hal_configure_default_isolation(
- uint32_t partition_idx,
- const struct platform_data_t *platform_data)
-{
- bool privileged = tfm_is_partition_privileged(partition_idx);
-#if defined(CONFIG_TFM_ENABLE_MEMORY_PROTECT) && (TFM_LVL != 1)
- struct mpu_armv8m_region_cfg_t region_cfg;
-#endif
-
- if (!platform_data) {
- return TFM_PLAT_ERR_INVALID_INPUT;
- }
-
-#if defined(CONFIG_TFM_ENABLE_MEMORY_PROTECT) && (TFM_LVL != 1)
- if (!privileged) {
- region_cfg.region_nr = PARTITION_REGION_PERIPH_START + periph_num_count;
- periph_num_count++;
- if (periph_num_count >= PARTITION_REGION_PERIPH_MAX_NUM) {
- return TFM_PLAT_ERR_MAX_VALUE;
- }
- region_cfg.region_base = platform_data->periph_start;
- region_cfg.region_limit = platform_data->periph_limit;
- region_cfg.region_attridx = MPU_ARMV8M_MAIR_ATTR_DEVICE_IDX;
- region_cfg.attr_access = MPU_ARMV8M_AP_RW_PRIV_UNPRIV;
- region_cfg.attr_sh = MPU_ARMV8M_SH_NONE;
- region_cfg.attr_exec = MPU_ARMV8M_XN_EXEC_NEVER;
-
- mpu_armv8m_disable(&dev_mpu_s);
-
- if (mpu_armv8m_region_enable(&dev_mpu_s, ®ion_cfg)
- != MPU_ARMV8M_OK) {
- return TFM_PLAT_ERR_SYSTEM_ERR;
- }
- mpu_armv8m_enable(&dev_mpu_s, PRIVILEGED_DEFAULT_ENABLE,
- HARDFAULT_NMI_ENABLE);
- }
-#endif /* defined(CONFIG_TFM_ENABLE_MEMORY_PROTECT) && (TFM_LVL != 1) */
-
- if (platform_data->periph_ppc_bank != PPC_SP_DO_NOT_CONFIGURE) {
- ppc_configure_to_secure(platform_data->periph_ppc_bank,
- platform_data->periph_ppc_loc);
- if (privileged) {
- ppc_clr_secure_unpriv(platform_data->periph_ppc_bank,
- platform_data->periph_ppc_loc);
- } else {
- ppc_en_secure_unpriv(platform_data->periph_ppc_bank,
- platform_data->periph_ppc_loc);
- }
- }
- return TFM_PLAT_ERR_SUCCESS;
-}
-
-void MPC_Handler(void)
-{
- /* Clear MPC interrupt flag and pending MPC IRQ */
- Driver_CODE_SRAM_MPC.ClearInterrupt();
- NVIC_ClearPendingIRQ(S_MPC_COMBINED_IRQn);
-
- /* Print fault message and block execution */
- ERROR_MSG("Oops... MPC fault!!!");
-
- /* Inform TF-M core that isolation boundary has been violated */
- tfm_access_violation_handler();
-}
-
-void PPC_Handler(void)
-{
- /*
- * Due to an issue on the FVP, the PPC fault doesn't trigger a
- * PPC IRQ which is handled by the PPC_handler.
- * In the FVP execution, this code is not execute.
- */
-
- /* Clear PPC interrupt flag and pending PPC IRQ */
- ppc_clear_irq();
- NVIC_ClearPendingIRQ(S_PPC_COMBINED_IRQn);
-
- /* Print fault message*/
- ERROR_MSG("Oops... PPC fault!!!");
-
- /* Inform TF-M core that isolation boundary has been violated */
- tfm_access_violation_handler();
-}
-
-uint32_t tfm_spm_hal_get_ns_VTOR(void)
-{
- return memory_regions.non_secure_code_start;
-}
-
-uint32_t tfm_spm_hal_get_ns_MSP(void)
-{
- return *((uint32_t *)memory_regions.non_secure_code_start);
-}
-
-uint32_t tfm_spm_hal_get_ns_entry_point(void)
-{
- return *((uint32_t *)(memory_regions.non_secure_code_start+ 4));
-}
-
-enum tfm_plat_err_t tfm_spm_hal_set_secure_irq_priority(IRQn_Type irq_line,
- uint32_t priority)
-{
- uint32_t quantized_priority = priority >> (8U - __NVIC_PRIO_BITS);
- NVIC_SetPriority(irq_line, quantized_priority);
- return TFM_PLAT_ERR_SUCCESS;
-}
-
-void tfm_spm_hal_clear_pending_irq(IRQn_Type irq_line)
-{
- NVIC_ClearPendingIRQ(irq_line);
-}
-
-void tfm_spm_hal_enable_irq(IRQn_Type irq_line)
-{
- NVIC_EnableIRQ(irq_line);
-}
-
-void tfm_spm_hal_disable_irq(IRQn_Type irq_line)
-{
- NVIC_DisableIRQ(irq_line);
-}
-
-enum irq_target_state_t tfm_spm_hal_set_irq_target_state(
- IRQn_Type irq_line,
- enum irq_target_state_t target_state)
-{
- uint32_t result;
-
- if (target_state == TFM_IRQ_TARGET_STATE_SECURE) {
- result = NVIC_ClearTargetState(irq_line);
- } else {
- result = NVIC_SetTargetState(irq_line);
- }
-
- if (result) {
- return TFM_IRQ_TARGET_STATE_NON_SECURE;
- } else {
- return TFM_IRQ_TARGET_STATE_SECURE;
- }
-}
-
-enum tfm_plat_err_t tfm_spm_hal_enable_fault_handlers(void)
-{
- return enable_fault_handlers();
-}
-
-enum tfm_plat_err_t tfm_spm_hal_system_reset_cfg(void)
-{
- return system_reset_cfg();
-}
-
-enum tfm_plat_err_t tfm_spm_hal_init_debug(void)
-{
- return init_debug();
-}
-
-enum tfm_plat_err_t tfm_spm_hal_nvic_interrupt_target_state_cfg(void)
-{
- return nvic_interrupt_target_state_cfg();
-}
-
-enum tfm_plat_err_t tfm_spm_hal_nvic_interrupt_enable(void)
-{
- return nvic_interrupt_enable();
-}
-
-enum tfm_hal_status_t tfm_hal_platform_init(void)
-{
- __enable_irq();
- stdio_init();
- LOG_MSG("\033[1;34m[Platform] MUSCA_A is marked for \
- deprecation!\033[0m\r\n");
-
- return TFM_HAL_SUCCESS;
-}
diff --git a/platform/ext/target/musca_a/target_cfg.c b/platform/ext/target/musca_a/target_cfg.c
deleted file mode 100644
index 18ff673..0000000
--- a/platform/ext/target/musca_a/target_cfg.c
+++ /dev/null
@@ -1,518 +0,0 @@
-/*
- * Copyright (c) 2018-2020 Arm Limited. All rights reserved.
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#include "target_cfg.h"
-#include "Driver_MPC.h"
-#include "platform_description.h"
-#include "device_definition.h"
-#include "region_defs.h"
-#include "tfm_plat_defs.h"
-#include "region.h"
-
-#define MIN(A, B) (((A) < (B)) ? (A) : (B))
-#define MAX(A, B) (((A) > (B)) ? (A) : (B))
-
-/* The section names come from the scatter file */
-REGION_DECLARE(Load$$LR$$, LR_NS_PARTITION, $$Base);
-REGION_DECLARE(Load$$LR$$, LR_VENEER, $$Base);
-REGION_DECLARE(Load$$LR$$, LR_VENEER, $$Limit);
-REGION_DECLARE(Load$$LR$$, LR_SECONDARY_PARTITION, $$Base);
-
-const struct memory_region_limits memory_regions = {
- .non_secure_code_start =
- (uint32_t)®ION_NAME(Load$$LR$$, LR_NS_PARTITION, $$Base) +
- BL2_HEADER_SIZE,
-
- .non_secure_partition_base =
- (uint32_t)®ION_NAME(Load$$LR$$, LR_NS_PARTITION, $$Base),
-
- .non_secure_partition_limit =
- (uint32_t)®ION_NAME(Load$$LR$$, LR_NS_PARTITION, $$Base) +
- NS_PARTITION_SIZE - 1,
-
- .veneer_base =
- (uint32_t)®ION_NAME(Load$$LR$$, LR_VENEER, $$Base),
-
- .veneer_limit =
- (uint32_t)®ION_NAME(Load$$LR$$, LR_VENEER, $$Limit),
-};
-
-/* Allows software, via SAU, to define the code region as a NSC */
-#define NSCCFG_CODENSC 1
-
-/* Import MPC driver */
-extern ARM_DRIVER_MPC Driver_CODE_SRAM_MPC, Driver_QSPI_MPC;
-extern ARM_DRIVER_MPC Driver_ISRAM0_MPC, Driver_ISRAM1_MPC;
-extern ARM_DRIVER_MPC Driver_ISRAM2_MPC, Driver_ISRAM3_MPC;
-
-/* Define Peripherals NS address range for the platform */
-#define PERIPHERALS_BASE_NS_START (0x40000000)
-#define PERIPHERALS_BASE_NS_END (0x4FFFFFFF)
-
-/* Enable system reset request for CPU 0 */
-#define ENABLE_CPU0_SYSTEM_RESET_REQUEST (1U << 4U)
-
-/* To write into AIRCR register, 0x5FA value must be write to the VECTKEY field,
- * otherwise the processor ignores the write.
- */
-#define SCB_AIRCR_WRITE_MASK ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos))
-
-/* Debug configuration flags */
-#define SPNIDEN_SEL_STATUS (0x01u << 7)
-#define SPNIDEN_STATUS (0x01u << 6)
-#define SPIDEN_SEL_STATUS (0x01u << 5)
-#define SPIDEN_STATUS (0x01u << 4)
-#define NIDEN_SEL_STATUS (0x01u << 3)
-#define NIDEN_STATUS (0x01u << 2)
-#define DBGEN_SEL_STATUS (0x01u << 1)
-#define DBGEN_STATUS (0x01u << 0)
-
-#define All_SEL_STATUS (SPNIDEN_SEL_STATUS | SPIDEN_SEL_STATUS | \
- NIDEN_SEL_STATUS | DBGEN_SEL_STATUS)
-
-struct platform_data_t tfm_peripheral_std_uart = {
- MUSCA_UART1_NS_BASE,
- MUSCA_UART1_NS_BASE + 0xFFF,
- PPC_SP_DO_NOT_CONFIGURE,
- -1
-};
-
-struct platform_data_t tfm_peripheral_timer0 = {
- MUSCA_CMSDK_TIMER0_S_BASE,
- MUSCA_CMSDK_TIMER1_S_BASE - 1,
- PPC_SP_APB_PPC0,
- CMSDK_TIMER0_APB_PPC_POS
-};
-
-#ifdef PSA_API_TEST_IPC
-
-/* Below data structure are only used for PSA FF tests, and this pattern is
- * definitely not to be followed for real life use cases, as it can break
- * security.
- */
-
-struct platform_data_t
- tfm_peripheral_FF_TEST_UART_REGION = {
- MUSCA_UART1_NS_BASE,
- MUSCA_UART1_NS_BASE + 0xFFF,
- PPC_SP_DO_NOT_CONFIGURE,
- -1
-};
-
-struct platform_data_t
- tfm_peripheral_FF_TEST_WATCHDOG_REGION = {
- MUSCA_CMSDK_WATCHDOG_S_BASE,
- MUSCA_CMSDK_WATCHDOG_S_BASE + 0xFFF,
- PPC_SP_DO_NOT_CONFIGURE,
- -1
-};
-
-#define FF_TEST_NVMEM_REGION_START 0x30017800
-#define FF_TEST_NVMEM_REGION_END 0x30017BFF
-#define FF_TEST_SERVER_PARTITION_MMIO_START 0x30017C00
-#define FF_TEST_SERVER_PARTITION_MMIO_END 0x30017D00
-#define FF_TEST_DRIVER_PARTITION_MMIO_START 0x30017E00
-#define FF_TEST_DRIVER_PARTITION_MMIO_END 0x30017F00
-
-struct platform_data_t
- tfm_peripheral_FF_TEST_NVMEM_REGION = {
- FF_TEST_NVMEM_REGION_START,
- FF_TEST_NVMEM_REGION_END,
- PPC_SP_DO_NOT_CONFIGURE,
- -1
-};
-
-struct platform_data_t
- tfm_peripheral_FF_TEST_SERVER_PARTITION_MMIO = {
- FF_TEST_SERVER_PARTITION_MMIO_START,
- FF_TEST_SERVER_PARTITION_MMIO_END,
- PPC_SP_DO_NOT_CONFIGURE,
- -1
-};
-
-struct platform_data_t
- tfm_peripheral_FF_TEST_DRIVER_PARTITION_MMIO = {
- FF_TEST_DRIVER_PARTITION_MMIO_START,
- FF_TEST_DRIVER_PARTITION_MMIO_END,
- PPC_SP_DO_NOT_CONFIGURE,
- -1
-};
-#endif
-
-enum tfm_plat_err_t enable_fault_handlers(void)
-{
- /* Explicitly set secure fault priority to the highest */
- NVIC_SetPriority(SecureFault_IRQn, 0);
-
- /* Enables BUS, MEM, USG and Secure faults */
- SCB->SHCSR |= SCB_SHCSR_USGFAULTENA_Msk
- | SCB_SHCSR_BUSFAULTENA_Msk
- | SCB_SHCSR_MEMFAULTENA_Msk
- | SCB_SHCSR_SECUREFAULTENA_Msk;
- return TFM_PLAT_ERR_SUCCESS;
-}
-
-enum tfm_plat_err_t system_reset_cfg(void)
-{
- struct sysctrl_t *sysctrl = (struct sysctrl_t *)CMSDK_SYSCTRL_BASE_S;
- uint32_t reg_value = SCB->AIRCR;
-
- /* Enable system reset request for CPU 0, to be triggered via
- * NVIC_SystemReset function.
- */
- sysctrl->resetmask |= ENABLE_CPU0_SYSTEM_RESET_REQUEST;
-
- /* Clear SCB_AIRCR_VECTKEY value */
- reg_value &= ~(uint32_t)(SCB_AIRCR_VECTKEY_Msk);
-
- /* Enable system reset request only to the secure world */
- reg_value |= (uint32_t)(SCB_AIRCR_WRITE_MASK | SCB_AIRCR_SYSRESETREQS_Msk);
-
- SCB->AIRCR = reg_value;
-
- return TFM_PLAT_ERR_SUCCESS;
-}
-
-enum tfm_plat_err_t init_debug(void)
-{
- volatile struct sysctrl_t *sys_ctrl =
- (struct sysctrl_t *)CMSDK_SYSCTRL_BASE_S;
-
-#if defined(DAUTH_NONE)
- /* Set all the debug enable selector bits to 1 */
- sys_ctrl->secdbgset = All_SEL_STATUS;
- /* Set all the debug enable bits to 0 */
- sys_ctrl->secdbgclr =
- DBGEN_STATUS | NIDEN_STATUS | SPIDEN_STATUS | SPNIDEN_STATUS;
-#elif defined(DAUTH_NS_ONLY)
- /* Set all the debug enable selector bits to 1 */
- sys_ctrl->secdbgset = All_SEL_STATUS;
- /* Set the debug enable bits to 1 for NS, and 0 for S mode */
- sys_ctrl->secdbgset = DBGEN_STATUS | NIDEN_STATUS;
- sys_ctrl->secdbgclr = SPIDEN_STATUS | SPNIDEN_STATUS;
-#elif defined(DAUTH_FULL)
- /* Set all the debug enable selector bits to 1 */
- sys_ctrl->secdbgset = All_SEL_STATUS;
- /* Set all the debug enable bits to 1 */
- sys_ctrl->secdbgset =
- DBGEN_STATUS | NIDEN_STATUS | SPIDEN_STATUS | SPNIDEN_STATUS;
-#else
-
-#if !defined(DAUTH_CHIP_DEFAULT)
-#error "No debug authentication setting is provided."
-#endif
-
- /* Set all the debug enable selector bits to 0 */
- sys_ctrl->secdbgclr = All_SEL_STATUS;
-
- /* No need to set any enable bits because the value depends on
- * input signals.
- */
-#endif
- return TFM_PLAT_ERR_SUCCESS;
-}
-
-/*----------------- NVIC interrupt target state to NS configuration ----------*/
-enum tfm_plat_err_t nvic_interrupt_target_state_cfg(void)
-{
- /* Target every interrupt to NS; unimplemented interrupts will be WI */
- for (uint8_t i=0; i<sizeof(NVIC->ITNS)/sizeof(NVIC->ITNS[0]); i++) {
- NVIC->ITNS[i] = 0xFFFFFFFF;
- }
-
- /* Make sure that MPC and PPC are targeted to S state */
- NVIC_ClearTargetState(S_MPC_COMBINED_IRQn);
- NVIC_ClearTargetState(S_PPC_COMBINED_IRQn);
-
- return TFM_PLAT_ERR_SUCCESS;
-}
-
-/*----------------- NVIC interrupt enabling for S peripherals ----------------*/
-enum tfm_plat_err_t nvic_interrupt_enable(void)
-{
- struct spctrl_def* spctrl = CMSDK_SPCTRL;
- int32_t ret = ARM_DRIVER_OK;
-
- /* MPC interrupt enabling */
- ret = Driver_QSPI_MPC.EnableInterrupt();
- if (ret != ARM_DRIVER_OK) {
- return TFM_PLAT_ERR_SYSTEM_ERR;
- }
- ret = Driver_CODE_SRAM_MPC.EnableInterrupt();
- if (ret != ARM_DRIVER_OK) {
- return TFM_PLAT_ERR_SYSTEM_ERR;
- }
- NVIC_EnableIRQ(S_MPC_COMBINED_IRQn);
-
- /* PPC interrupt enabling */
- /* Clear pending PPC interrupts */
- /* In the PPC configuration function, we have used the Non-Secure
- * Privilege Control Block to grant unprivilged NS access to some
- * peripherals used by NS. That triggers a PPC0 exception as that
- * register is meant for NS privileged access only. Clear it here
- */
- spctrl->secppcintclr = CMSDK_APB_PPC0_INT_POS_MASK;
-
- /* Enable PPC interrupts for APB PPC */
- spctrl->secppcinten |= CMSDK_APB_PPC0_INT_POS_MASK;
- spctrl->secppcinten |= CMSDK_APB_PPC1_INT_POS_MASK;
- spctrl->secppcinten |= CMSDK_APB_PPCEXP0_INT_POS_MASK;
- spctrl->secppcinten |= CMSDK_APB_PPCEXP1_INT_POS_MASK;
- spctrl->secppcinten |= CMSDK_APB_PPCEXP2_INT_POS_MASK;
- spctrl->secppcinten |= CMSDK_APB_PPCEXP3_INT_POS_MASK;
- NVIC_EnableIRQ(S_PPC_COMBINED_IRQn);
-
-#ifdef PSA_API_TEST_IPC
- NVIC_EnableIRQ(FF_TEST_UART_IRQ);
-#endif
-
- return TFM_PLAT_ERR_SUCCESS;
-}
-
-/*------------------- SAU/IDAU configuration functions -----------------------*/
-
-void sau_and_idau_cfg(void)
-{
- /* Enables SAU */
- TZ_SAU_Enable();
-
- /* Configures SAU regions to be non-secure */
- SAU->RNR = 0U;
- SAU->RBAR = (memory_regions.non_secure_partition_base
- & SAU_RBAR_BADDR_Msk);
- SAU->RLAR = (memory_regions.non_secure_partition_limit
- & SAU_RLAR_LADDR_Msk)
- | SAU_RLAR_ENABLE_Msk;
-
- SAU->RNR = 1U;
- SAU->RBAR = (NS_DATA_START & SAU_RBAR_BADDR_Msk);
- SAU->RLAR = (NS_DATA_LIMIT & SAU_RLAR_LADDR_Msk) | SAU_RLAR_ENABLE_Msk;
-
- /* Configures veneers region to be non-secure callable */
- SAU->RNR = 2U;
- SAU->RBAR = (memory_regions.veneer_base & SAU_RBAR_BADDR_Msk);
- SAU->RLAR = (memory_regions.veneer_limit & SAU_RLAR_LADDR_Msk)
- | SAU_RLAR_ENABLE_Msk
- | SAU_RLAR_NSC_Msk;
-
- /* Configure the peripherals space */
- SAU->RNR = 3U;
- SAU->RBAR = (PERIPHERALS_BASE_NS_START & SAU_RBAR_BADDR_Msk);
- SAU->RLAR = (PERIPHERALS_BASE_NS_END & SAU_RLAR_LADDR_Msk)
- | SAU_RLAR_ENABLE_Msk;
-
- /* Allows SAU to define the code region as a NSC */
- struct spctrl_def* spctrl = CMSDK_SPCTRL;
- spctrl->nsccfg |= NSCCFG_CODENSC;
-}
-
-/*------------------- Memory configuration functions -------------------------*/
-
-int32_t mpc_init_region_with_attr(ARM_DRIVER_MPC *region,
- uintptr_t region_base, uintptr_t region_limit,
- uintptr_t attr_range_start, uintptr_t attr_range_limit,
- ARM_MPC_SEC_ATTR attr)
-{
- uintptr_t range_start = MAX(region_base, attr_range_start);
- uintptr_t range_limit = MIN(region_limit, attr_range_limit);
-
- if (range_start < range_limit) {
- /* ConfigRegion checks whether the range addresses are aligned at MPC
- * block border
- */
- return region->ConfigRegion(range_start, range_limit, attr);
- }
- return ARM_DRIVER_OK;
-}
-
-int32_t mpc_init_cfg(void)
-{
- int32_t ret = ARM_DRIVER_OK;
-
- ARM_DRIVER_MPC* mpc_data_region0 = &Driver_ISRAM0_MPC;
- ARM_DRIVER_MPC* mpc_data_region1 = &Driver_ISRAM1_MPC;
- ARM_DRIVER_MPC* mpc_data_region2 = &Driver_ISRAM2_MPC;
- ARM_DRIVER_MPC* mpc_data_region3 = &Driver_ISRAM3_MPC;
-
- ret = Driver_QSPI_MPC.Initialize();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
-
- ret = Driver_CODE_SRAM_MPC.Initialize();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = Driver_CODE_SRAM_MPC.ConfigRegion(
- memory_regions.non_secure_partition_base,
- memory_regions.non_secure_partition_limit,
- ARM_MPC_ATTR_NONSECURE);
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
-
- ret = mpc_data_region0->Initialize();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = mpc_data_region0->ConfigRegion(MPC_ISRAM0_RANGE_BASE_S,
- MPC_ISRAM0_RANGE_LIMIT_S,
- ARM_MPC_ATTR_SECURE);
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
-
- ret = mpc_data_region1->Initialize();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = mpc_data_region1->ConfigRegion(MPC_ISRAM1_RANGE_BASE_S,
- MPC_ISRAM1_RANGE_LIMIT_S,
- ARM_MPC_ATTR_SECURE);
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
-
- ret = mpc_data_region2->Initialize();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = mpc_data_region2->ConfigRegion(MPC_ISRAM2_RANGE_BASE_S,
- MPC_ISRAM2_RANGE_LIMIT_S,
- ARM_MPC_ATTR_SECURE);
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
-
- /* Set MPC_ISRAM3 based on regions defined in region_defs.h */
- ret = mpc_data_region3->Initialize();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = mpc_init_region_with_attr(mpc_data_region3,
- MPC_ISRAM3_RANGE_BASE_S, MPC_ISRAM3_RANGE_LIMIT_S,
- S_DATA_START, S_DATA_LIMIT,
- ARM_MPC_ATTR_SECURE);
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = mpc_init_region_with_attr(
- mpc_data_region3,
- MPC_ISRAM3_RANGE_BASE_NS, MPC_ISRAM3_RANGE_LIMIT_NS,
- NS_DATA_START, NS_DATA_LIMIT,
- ARM_MPC_ATTR_NONSECURE);
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
-
- /* Lock down the MPC configuration */
- ret = Driver_QSPI_MPC.LockDown();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = Driver_CODE_SRAM_MPC.LockDown();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = mpc_data_region0->LockDown();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = mpc_data_region1->LockDown();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = mpc_data_region2->LockDown();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
- ret = mpc_data_region3->LockDown();
- if (ret != ARM_DRIVER_OK) {
- return ret;
- }
-
- /* Add barriers to assure the MPC configuration is done before continue
- * the execution.
- */
- __DSB();
- __ISB();
-
- return ARM_DRIVER_OK;
-}
-
-/*---------------------- PPC configuration functions -------------------------*/
-
-void ppc_init_cfg(void)
-{
- struct spctrl_def* spctrl = CMSDK_SPCTRL;
- struct nspctrl_def* nspctrl = CMSDK_NSPCTRL;
-
- /* Grant non-secure access to peripherals in the PPC0
- * (timer0 and 1, dualtimer, watchdog, mhu 0 and 1)
- */
- spctrl->apbnsppc0 |= (1U << CMSDK_TIMER0_APB_PPC_POS);
- spctrl->apbnsppc0 |= (1U << CMSDK_TIMER1_APB_PPC_POS);
- spctrl->apbnsppc0 |= (1U << CMSDK_DTIMER_APB_PPC_POS);
- spctrl->apbnsppc0 |= (1U << CMSDK_MHU0_APB_PPC_POS);
- spctrl->apbnsppc0 |= (1U << CMSDK_MHU1_APB_PPC_POS);
-
- /* Grant non-secure access to S32K Timer in PPC1*/
- spctrl->apbnsppc1 |= (1U << CMSDK_S32K_TIMER_PPC_POS);
-
- /* Grant non-secure access for AHB peripherals on EXP0 */
- spctrl->ahbnsppcexp0 = (1U << MUSCA_PERIPHS_AHB_PPC_POS);
-
- /* in NS, grant un-privileged for AHB peripherals on EXP0 */
- nspctrl->ahbnspppcexp0 = (1U << MUSCA_PERIPHS_AHB_PPC_POS);
-
- /* Configure the response to a security violation as a
- * bus error instead of RAZ/WI
- */
- spctrl->secrespcfg |= 1U;
-}
-
-void ppc_configure_to_non_secure(enum ppc_bank_e bank, uint16_t pos)
-{
- /* Setting NS flag for peripheral to enable NS access */
- struct spctrl_def* spctrl = CMSDK_SPCTRL;
- ((uint32_t*)&(spctrl->ahbnsppc0))[bank] |= (1U << pos);
-}
-
-void ppc_configure_to_secure(enum ppc_bank_e bank, uint16_t pos)
-{
- /* Clear NS flag for peripheral to prevent NS access */
- struct spctrl_def* spctrl = CMSDK_SPCTRL;
- ((uint32_t*)&(spctrl->ahbnsppc0))[bank] &= ~(1U << pos);
-}
-
-void ppc_en_secure_unpriv(enum ppc_bank_e bank, uint16_t pos)
-{
- struct spctrl_def* spctrl = CMSDK_SPCTRL;
- ((uint32_t*)&(spctrl->ahbspppc0))[bank] |= (1U << pos);
-}
-
-void ppc_clr_secure_unpriv(enum ppc_bank_e bank, uint16_t pos)
-{
- struct spctrl_def* spctrl = CMSDK_SPCTRL;
- ((uint32_t*)&(spctrl->ahbspppc0))[bank] &= ~(1U << pos);
-}
-
-void ppc_clear_irq(void)
-{
- struct spctrl_def* spctrl = CMSDK_SPCTRL;
- /* Clear APB PPC EXP2 IRQ */
- spctrl->secppcintclr = CMSDK_APB_PPCEXP2_INT_POS_MASK;
-}
diff --git a/platform/ext/target/musca_a/target_cfg.h b/platform/ext/target/musca_a/target_cfg.h
deleted file mode 100644
index 86796a9..0000000
--- a/platform/ext/target/musca_a/target_cfg.h
+++ /dev/null
@@ -1,155 +0,0 @@
-/*
- * Copyright (c) 2018-2020 Arm Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-
-#ifndef __TARGET_CFG_H__
-#define __TARGET_CFG_H__
-
-#include "uart_stdout.h"
-#include "tfm_peripherals_def.h"
-#include "uart_pl011_drv.h"
-
-#define TFM_DRIVER_STDIO Driver_USART1
-#define NS_DRIVER_STDIO Driver_USART1
-
-/**
- * \brief Defines the word offsets of Slave Peripheral Protection Controller
- * Registers
- */
-enum ppc_bank_e
-{
- PPC_SP_DO_NOT_CONFIGURE = -1,
- PPC_SP_AHB_PPC0 = 0,
- PPC_SP_RES0,
- PPC_SP_RES1,
- PPC_SP_RES2,
- PPC_SP_AHB_PPC_EXP0,
- PPC_SP_AHB_PPC_EXP1,
- PPC_SP_AHB_PPC_EXP2,
- PPC_SP_AHB_PPC_EXP3,
- PPC_SP_APB_PPC0,
- PPC_SP_APB_PPC1,
- PPC_SP_RES3,
- PPC_SP_RES4,
- PPC_SP_APB_PPC_EXP0,
- PPC_SP_APB_PPC_EXP1,
- PPC_SP_APB_PPC_EXP2,
- PPC_SP_APB_PPC_EXP3,
-};
-
-/**
- * \brief Store the addresses of memory regions
- */
-struct memory_region_limits {
- uint32_t non_secure_code_start;
- uint32_t non_secure_partition_base;
- uint32_t non_secure_partition_limit;
- uint32_t veneer_base;
- uint32_t veneer_limit;
-};
-
-/**
- * \brief Holds the data necessary to do isolation for a specific peripheral.
- */
-struct platform_data_t
-{
- uint32_t periph_start;
- uint32_t periph_limit;
- enum ppc_bank_e periph_ppc_bank;
- int16_t periph_ppc_loc;
-};
-
-/**
- * \brief Configures the Memory Protection Controller.
- *
- * \return Returns error code.
- */
-int32_t mpc_init_cfg(void);
-
-/**
- * \brief Configures the Peripheral Protection Controller.
- */
-void ppc_init_cfg(void);
-
-/**
- * \brief Restict access to peripheral to secure
- */
-void ppc_configure_to_secure(enum ppc_bank_e bank, uint16_t loc);
-
-/**
- * \brief Allow non-secure access to peripheral
- */
-void ppc_configure_to_non_secure(enum ppc_bank_e bank, uint16_t loc);
-
-/**
- * \brief Enable secure unprivileged access to peripheral
- */
-void ppc_en_secure_unpriv(enum ppc_bank_e bank, uint16_t pos);
-
-/**
- * \brief Clear secure unprivileged access to peripheral
- */
-void ppc_clr_secure_unpriv(enum ppc_bank_e bank, uint16_t pos);
-
-/**
- * \brief Clears PPC interrupt.
- */
-void ppc_clear_irq(void);
-
-/**
- * \brief Configures SAU and IDAU.
- */
-void sau_and_idau_cfg(void);
-
-/**
- * \brief Enables the fault handlers and sets priorities.
- *
- * \return Returns values as specified by the \ref tfm_plat_err_t
- */
-enum tfm_plat_err_t enable_fault_handlers(void);
-
-/**
- * \brief Configures the system reset request properties
- *
- * \return Returns values as specified by the \ref tfm_plat_err_t
- */
-enum tfm_plat_err_t system_reset_cfg(void);
-
-/**
- * \brief Configures the system debug properties.
- *
- * \return Returns values as specified by the \ref tfm_plat_err_t
- */
-enum tfm_plat_err_t init_debug(void);
-
-/**
- * \brief Configures all external interrupts to target the
- * NS state, apart for the ones associated to secure
- * peripherals (plus MPC and PPC)
- *
- * \return Returns values as specified by the \ref tfm_plat_err_t
- */
-enum tfm_plat_err_t nvic_interrupt_target_state_cfg(void);
-
-/**
- * \brief This function enable the interrupts associated
- * to the secure peripherals (plus the isolation boundary violation
- * interrupts)
- *
- * \return Returns values as specified by the \ref tfm_plat_err_t
- */
-enum tfm_plat_err_t nvic_interrupt_enable(void);
-
-#endif /* __TARGET_CFG_H__ */
diff --git a/platform/ext/target/musca_a/tfm_hal_isolation.c b/platform/ext/target/musca_a/tfm_hal_isolation.c
deleted file mode 100644
index 5c44164..0000000
--- a/platform/ext/target/musca_a/tfm_hal_isolation.c
+++ /dev/null
@@ -1,146 +0,0 @@
-/*
- * Copyright (c) 2020, Arm Limited. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#include "cmsis.h"
-#include "Driver_Common.h"
-#include "mpu_armv8m_drv.h"
-#include "region.h"
-#include "target_cfg.h"
-#include "tfm_hal_isolation.h"
-
-#ifdef CONFIG_TFM_ENABLE_MEMORY_PROTECT
-#define MPU_REGION_VENEERS 0
-#define MPU_REGION_TFM_UNPRIV_CODE 1
-#define MPU_REGION_NS_STACK 2
-#define PARTITION_REGION_RO 3
-#define PARTITION_REGION_RW_STACK 4
-#ifdef TFM_SP_META_PTR_ENABLE
-#define MPU_REGION_SP_META_PTR 7
-#endif /* TFM_SP_META_PTR_ENABLE */
-
-REGION_DECLARE(Image$$, TFM_UNPRIV_CODE, $$RO$$Base);
-REGION_DECLARE(Image$$, TFM_UNPRIV_CODE, $$RO$$Limit);
-REGION_DECLARE(Image$$, TFM_APP_CODE_START, $$Base);
-REGION_DECLARE(Image$$, TFM_APP_CODE_END, $$Base);
-REGION_DECLARE(Image$$, TFM_APP_RW_STACK_START, $$Base);
-REGION_DECLARE(Image$$, TFM_APP_RW_STACK_END, $$Base);
-REGION_DECLARE(Image$$, ARM_LIB_STACK, $$ZI$$Base);
-REGION_DECLARE(Image$$, ARM_LIB_STACK, $$ZI$$Limit);
-#ifdef TFM_SP_META_PTR_ENABLE
-REGION_DECLARE(Image$$, TFM_SP_META_PTR, $$RW$$Base);
-REGION_DECLARE(Image$$, TFM_SP_META_PTR, $$RW$$Limit);
-#endif
-
-extern const struct memory_region_limits memory_regions;
-#endif /* CONFIG_TFM_ENABLE_MEMORY_PROTECT */
-
-enum tfm_hal_status_t tfm_hal_set_up_static_boundaries(void)
-{
- /* Set up isolation boundaries between SPE and NSPE */
- sau_and_idau_cfg();
- if (mpc_init_cfg() != ARM_DRIVER_OK) {
- return TFM_HAL_ERROR_GENERIC;
- }
- ppc_init_cfg();
-
- /* Set up static isolation boundaries inside SPE */
-#ifdef CONFIG_TFM_ENABLE_MEMORY_PROTECT
- struct mpu_armv8m_region_cfg_t region_cfg;
- struct mpu_armv8m_dev_t dev_mpu_s = { MPU_BASE };
-
- mpu_armv8m_clean(&dev_mpu_s);
-
- /* Veneer region */
- region_cfg.region_nr = MPU_REGION_VENEERS;
- region_cfg.region_base = memory_regions.veneer_base;
- region_cfg.region_limit = memory_regions.veneer_limit;
- region_cfg.region_attridx = MPU_ARMV8M_MAIR_ATTR_CODE_IDX;
- region_cfg.attr_access = MPU_ARMV8M_AP_RO_PRIV_UNPRIV;
- region_cfg.attr_sh = MPU_ARMV8M_SH_NONE;
- region_cfg.attr_exec = MPU_ARMV8M_XN_EXEC_OK;
- if (mpu_armv8m_region_enable(&dev_mpu_s, ®ion_cfg) != MPU_ARMV8M_OK) {
- return TFM_HAL_ERROR_GENERIC;
- }
-
- /* TFM Core unprivileged code region */
- region_cfg.region_nr = MPU_REGION_TFM_UNPRIV_CODE;
- region_cfg.region_base =
- (uint32_t)®ION_NAME(Image$$, TFM_UNPRIV_CODE, $$RO$$Base);
- region_cfg.region_limit =
- (uint32_t)®ION_NAME(Image$$, TFM_UNPRIV_CODE, $$RO$$Limit);
- region_cfg.region_attridx = MPU_ARMV8M_MAIR_ATTR_CODE_IDX;
- region_cfg.attr_access = MPU_ARMV8M_AP_RO_PRIV_UNPRIV;
- region_cfg.attr_sh = MPU_ARMV8M_SH_NONE;
- region_cfg.attr_exec = MPU_ARMV8M_XN_EXEC_OK;
- if (mpu_armv8m_region_enable(&dev_mpu_s, ®ion_cfg) != MPU_ARMV8M_OK) {
- return TFM_HAL_ERROR_GENERIC;
- }
-
- /* NSPM PSP */
- region_cfg.region_nr = MPU_REGION_NS_STACK;
- region_cfg.region_base =
- (uint32_t)®ION_NAME(Image$$, ARM_LIB_STACK, $$ZI$$Base);
- region_cfg.region_limit =
- (uint32_t)®ION_NAME(Image$$, ARM_LIB_STACK, $$ZI$$Limit);
- region_cfg.region_attridx = MPU_ARMV8M_MAIR_ATTR_DATA_IDX;
- region_cfg.attr_access = MPU_ARMV8M_AP_RW_PRIV_UNPRIV;
- region_cfg.attr_sh = MPU_ARMV8M_SH_NONE;
- region_cfg.attr_exec = MPU_ARMV8M_XN_EXEC_NEVER;
- if (mpu_armv8m_region_enable(&dev_mpu_s, ®ion_cfg) != MPU_ARMV8M_OK) {
- return TFM_HAL_ERROR_GENERIC;
- }
-
- /* RO region */
- region_cfg.region_nr = PARTITION_REGION_RO;
- region_cfg.region_base =
- (uint32_t)®ION_NAME(Image$$, TFM_APP_CODE_START, $$Base);
- region_cfg.region_limit =
- (uint32_t)®ION_NAME(Image$$, TFM_APP_CODE_END, $$Base);
- region_cfg.region_attridx = MPU_ARMV8M_MAIR_ATTR_CODE_IDX;
- region_cfg.attr_access = MPU_ARMV8M_AP_RO_PRIV_UNPRIV;
- region_cfg.attr_sh = MPU_ARMV8M_SH_NONE;
- region_cfg.attr_exec = MPU_ARMV8M_XN_EXEC_OK;
- if (mpu_armv8m_region_enable(&dev_mpu_s, ®ion_cfg) != MPU_ARMV8M_OK) {
- return TFM_HAL_ERROR_GENERIC;
- }
-
- /* RW, ZI and stack as one region */
- region_cfg.region_nr = PARTITION_REGION_RW_STACK;
- region_cfg.region_base =
- (uint32_t)®ION_NAME(Image$$, TFM_APP_RW_STACK_START, $$Base);
- region_cfg.region_limit =
- (uint32_t)®ION_NAME(Image$$, TFM_APP_RW_STACK_END, $$Base);
- region_cfg.region_attridx = MPU_ARMV8M_MAIR_ATTR_DATA_IDX;
- region_cfg.attr_access = MPU_ARMV8M_AP_RW_PRIV_UNPRIV;
- region_cfg.attr_sh = MPU_ARMV8M_SH_NONE;
- region_cfg.attr_exec = MPU_ARMV8M_XN_EXEC_NEVER;
- if (mpu_armv8m_region_enable(&dev_mpu_s, ®ion_cfg) != MPU_ARMV8M_OK) {
- return TFM_HAL_ERROR_GENERIC;
- }
-
-#ifdef TFM_SP_META_PTR_ENABLE
- /* TFM partition metadata pointer region */
- region_cfg.region_nr = MPU_REGION_SP_META_PTR;
- region_cfg.region_base =
- (uint32_t)®ION_NAME(Image$$, TFM_SP_META_PTR, $$RW$$Base);
- region_cfg.region_limit =
- (uint32_t)®ION_NAME(Image$$, TFM_SP_META_PTR, $$RW$$Limit);
- region_cfg.region_attridx = MPU_ARMV8M_MAIR_ATTR_DATA_IDX;
- region_cfg.attr_access = MPU_ARMV8M_AP_RW_PRIV_UNPRIV;
- region_cfg.attr_sh = MPU_ARMV8M_SH_NONE;
- region_cfg.attr_exec = MPU_ARMV8M_XN_EXEC_NEVER;
- if (mpu_armv8m_region_enable(&dev_mpu_s, ®ion_cfg) != MPU_ARMV8M_OK) {
- return TFM_HAL_ERROR_GENERIC;
- }
-#endif
-
- mpu_armv8m_enable(&dev_mpu_s, PRIVILEGED_DEFAULT_ENABLE,
- HARDFAULT_NMI_ENABLE);
-#endif /* CONFIG_TFM_ENABLE_MEMORY_PROTECT */
-
- return TFM_HAL_SUCCESS;
-}
diff --git a/platform/ext/target/musca_a/tfm_peripherals_def.h b/platform/ext/target/musca_a/tfm_peripherals_def.h
deleted file mode 100644
index a0887ac..0000000
--- a/platform/ext/target/musca_a/tfm_peripherals_def.h
+++ /dev/null
@@ -1,49 +0,0 @@
-/*
- * Copyright (c) 2018-2020, Arm Limited. All rights reserved.
- * Copyright (c) 2020, Cypress Semiconductor Corporation. All rights reserved.
- *
- * SPDX-License-Identifier: BSD-3-Clause
- *
- */
-
-#ifndef __TFM_PERIPHERALS_DEF_H__
-#define __TFM_PERIPHERALS_DEF_H__
-
-#include "platform_irq.h"
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-#define TFM_TIMER0_IRQ (TIMER0_IRQn)
-#define TFM_TIMER1_IRQ (TIMER1_IRQn)
-#define FF_TEST_UART_IRQ (UART1_Tx_IRQn)
-#define FF_TEST_UART_IRQ_Handler UARTTX1_Handler
-
-struct platform_data_t;
-
-extern struct platform_data_t tfm_peripheral_std_uart;
-extern struct platform_data_t tfm_peripheral_timer0;
-
-#define TFM_PERIPHERAL_STD_UART (&tfm_peripheral_std_uart)
-#define TFM_PERIPHERAL_TIMER0 (&tfm_peripheral_timer0)
-#define TFM_PERIPHERAL_FPGA_IO (0)
-
-#ifdef PSA_API_TEST_IPC
-extern struct platform_data_t tfm_peripheral_FF_TEST_UART_REGION;
-extern struct platform_data_t tfm_peripheral_FF_TEST_WATCHDOG_REGION;
-extern struct platform_data_t tfm_peripheral_FF_TEST_NVMEM_REGION;
-extern struct platform_data_t tfm_peripheral_FF_TEST_SERVER_PARTITION_MMIO;
-extern struct platform_data_t tfm_peripheral_FF_TEST_DRIVER_PARTITION_MMIO;
-#define FF_TEST_UART_REGION (&tfm_peripheral_FF_TEST_UART_REGION)
-#define FF_TEST_WATCHDOG_REGION (&tfm_peripheral_FF_TEST_WATCHDOG_REGION)
-#define FF_TEST_NVMEM_REGION (&tfm_peripheral_FF_TEST_NVMEM_REGION)
-#define FF_TEST_SERVER_PARTITION_MMIO (&tfm_peripheral_FF_TEST_SERVER_PARTITION_MMIO)
-#define FF_TEST_DRIVER_PARTITION_MMIO (&tfm_peripheral_FF_TEST_DRIVER_PARTITION_MMIO)
-#endif /* PSA_API_TEST_IPC */
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __TFM_PERIPHERALS_DEF_H__ */