v4.19.13 snapshot.
diff --git a/drivers/pwm/pwm-imx.c b/drivers/pwm/pwm-imx.c
new file mode 100644
index 0000000..1d5242c
--- /dev/null
+++ b/drivers/pwm/pwm-imx.c
@@ -0,0 +1,333 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * simple driver for PWM (Pulse Width Modulator) controller
+ *
+ * Derived from pxa PWM driver by eric miao <eric.miao@marvell.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/pwm.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+
+/* i.MX1 and i.MX21 share the same PWM function block: */
+
+#define MX1_PWMC 0x00 /* PWM Control Register */
+#define MX1_PWMS 0x04 /* PWM Sample Register */
+#define MX1_PWMP 0x08 /* PWM Period Register */
+
+#define MX1_PWMC_EN (1 << 4)
+
+/* i.MX27, i.MX31, i.MX35 share the same PWM function block: */
+
+#define MX3_PWMCR 0x00 /* PWM Control Register */
+#define MX3_PWMSR 0x04 /* PWM Status Register */
+#define MX3_PWMSAR 0x0C /* PWM Sample Register */
+#define MX3_PWMPR 0x10 /* PWM Period Register */
+#define MX3_PWMCR_PRESCALER(x) ((((x) - 1) & 0xFFF) << 4)
+#define MX3_PWMCR_STOPEN (1 << 25)
+#define MX3_PWMCR_DOZEEN (1 << 24)
+#define MX3_PWMCR_WAITEN (1 << 23)
+#define MX3_PWMCR_DBGEN (1 << 22)
+#define MX3_PWMCR_POUTC (1 << 18)
+#define MX3_PWMCR_CLKSRC_IPG_HIGH (2 << 16)
+#define MX3_PWMCR_CLKSRC_IPG (1 << 16)
+#define MX3_PWMCR_SWR (1 << 3)
+#define MX3_PWMCR_EN (1 << 0)
+#define MX3_PWMSR_FIFOAV_4WORDS 0x4
+#define MX3_PWMSR_FIFOAV_MASK 0x7
+
+#define MX3_PWM_SWR_LOOP 5
+
+struct imx_chip {
+ struct clk *clk_per;
+
+ void __iomem *mmio_base;
+
+ struct pwm_chip chip;
+};
+
+#define to_imx_chip(chip) container_of(chip, struct imx_chip, chip)
+
+static int imx_pwm_config_v1(struct pwm_chip *chip,
+ struct pwm_device *pwm, int duty_ns, int period_ns)
+{
+ struct imx_chip *imx = to_imx_chip(chip);
+
+ /*
+ * The PWM subsystem allows for exact frequencies. However,
+ * I cannot connect a scope on my device to the PWM line and
+ * thus cannot provide the program the PWM controller
+ * exactly. Instead, I'm relying on the fact that the
+ * Bootloader (u-boot or WinCE+haret) has programmed the PWM
+ * function group already. So I'll just modify the PWM sample
+ * register to follow the ratio of duty_ns vs. period_ns
+ * accordingly.
+ *
+ * This is good enough for programming the brightness of
+ * the LCD backlight.
+ *
+ * The real implementation would divide PERCLK[0] first by
+ * both the prescaler (/1 .. /128) and then by CLKSEL
+ * (/2 .. /16).
+ */
+ u32 max = readl(imx->mmio_base + MX1_PWMP);
+ u32 p = max * duty_ns / period_ns;
+ writel(max - p, imx->mmio_base + MX1_PWMS);
+
+ return 0;
+}
+
+static int imx_pwm_enable_v1(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+ struct imx_chip *imx = to_imx_chip(chip);
+ u32 val;
+ int ret;
+
+ ret = clk_prepare_enable(imx->clk_per);
+ if (ret < 0)
+ return ret;
+
+ val = readl(imx->mmio_base + MX1_PWMC);
+ val |= MX1_PWMC_EN;
+ writel(val, imx->mmio_base + MX1_PWMC);
+
+ return 0;
+}
+
+static void imx_pwm_disable_v1(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+ struct imx_chip *imx = to_imx_chip(chip);
+ u32 val;
+
+ val = readl(imx->mmio_base + MX1_PWMC);
+ val &= ~MX1_PWMC_EN;
+ writel(val, imx->mmio_base + MX1_PWMC);
+
+ clk_disable_unprepare(imx->clk_per);
+}
+
+static void imx_pwm_sw_reset(struct pwm_chip *chip)
+{
+ struct imx_chip *imx = to_imx_chip(chip);
+ struct device *dev = chip->dev;
+ int wait_count = 0;
+ u32 cr;
+
+ writel(MX3_PWMCR_SWR, imx->mmio_base + MX3_PWMCR);
+ do {
+ usleep_range(200, 1000);
+ cr = readl(imx->mmio_base + MX3_PWMCR);
+ } while ((cr & MX3_PWMCR_SWR) &&
+ (wait_count++ < MX3_PWM_SWR_LOOP));
+
+ if (cr & MX3_PWMCR_SWR)
+ dev_warn(dev, "software reset timeout\n");
+}
+
+static void imx_pwm_wait_fifo_slot(struct pwm_chip *chip,
+ struct pwm_device *pwm)
+{
+ struct imx_chip *imx = to_imx_chip(chip);
+ struct device *dev = chip->dev;
+ unsigned int period_ms;
+ int fifoav;
+ u32 sr;
+
+ sr = readl(imx->mmio_base + MX3_PWMSR);
+ fifoav = sr & MX3_PWMSR_FIFOAV_MASK;
+ if (fifoav == MX3_PWMSR_FIFOAV_4WORDS) {
+ period_ms = DIV_ROUND_UP(pwm_get_period(pwm),
+ NSEC_PER_MSEC);
+ msleep(period_ms);
+
+ sr = readl(imx->mmio_base + MX3_PWMSR);
+ if (fifoav == (sr & MX3_PWMSR_FIFOAV_MASK))
+ dev_warn(dev, "there is no free FIFO slot\n");
+ }
+}
+
+static int imx_pwm_apply_v2(struct pwm_chip *chip, struct pwm_device *pwm,
+ struct pwm_state *state)
+{
+ unsigned long period_cycles, duty_cycles, prescale;
+ struct imx_chip *imx = to_imx_chip(chip);
+ struct pwm_state cstate;
+ unsigned long long c;
+ int ret;
+ u32 cr;
+
+ pwm_get_state(pwm, &cstate);
+
+ if (state->enabled) {
+ c = clk_get_rate(imx->clk_per);
+ c *= state->period;
+
+ do_div(c, 1000000000);
+ period_cycles = c;
+
+ prescale = period_cycles / 0x10000 + 1;
+
+ period_cycles /= prescale;
+ c = (unsigned long long)period_cycles * state->duty_cycle;
+ do_div(c, state->period);
+ duty_cycles = c;
+
+ /*
+ * according to imx pwm RM, the real period value should be
+ * PERIOD value in PWMPR plus 2.
+ */
+ if (period_cycles > 2)
+ period_cycles -= 2;
+ else
+ period_cycles = 0;
+
+ /*
+ * Wait for a free FIFO slot if the PWM is already enabled, and
+ * flush the FIFO if the PWM was disabled and is about to be
+ * enabled.
+ */
+ if (cstate.enabled) {
+ imx_pwm_wait_fifo_slot(chip, pwm);
+ } else {
+ ret = clk_prepare_enable(imx->clk_per);
+ if (ret)
+ return ret;
+
+ imx_pwm_sw_reset(chip);
+ }
+
+ writel(duty_cycles, imx->mmio_base + MX3_PWMSAR);
+ writel(period_cycles, imx->mmio_base + MX3_PWMPR);
+
+ cr = MX3_PWMCR_PRESCALER(prescale) |
+ MX3_PWMCR_STOPEN | MX3_PWMCR_DOZEEN | MX3_PWMCR_WAITEN |
+ MX3_PWMCR_DBGEN | MX3_PWMCR_CLKSRC_IPG_HIGH |
+ MX3_PWMCR_EN;
+
+ if (state->polarity == PWM_POLARITY_INVERSED)
+ cr |= MX3_PWMCR_POUTC;
+
+ writel(cr, imx->mmio_base + MX3_PWMCR);
+ } else if (cstate.enabled) {
+ writel(0, imx->mmio_base + MX3_PWMCR);
+
+ clk_disable_unprepare(imx->clk_per);
+ }
+
+ return 0;
+}
+
+static const struct pwm_ops imx_pwm_ops_v1 = {
+ .enable = imx_pwm_enable_v1,
+ .disable = imx_pwm_disable_v1,
+ .config = imx_pwm_config_v1,
+ .owner = THIS_MODULE,
+};
+
+static const struct pwm_ops imx_pwm_ops_v2 = {
+ .apply = imx_pwm_apply_v2,
+ .owner = THIS_MODULE,
+};
+
+struct imx_pwm_data {
+ bool polarity_supported;
+ const struct pwm_ops *ops;
+};
+
+static struct imx_pwm_data imx_pwm_data_v1 = {
+ .ops = &imx_pwm_ops_v1,
+};
+
+static struct imx_pwm_data imx_pwm_data_v2 = {
+ .polarity_supported = true,
+ .ops = &imx_pwm_ops_v2,
+};
+
+static const struct of_device_id imx_pwm_dt_ids[] = {
+ { .compatible = "fsl,imx1-pwm", .data = &imx_pwm_data_v1, },
+ { .compatible = "fsl,imx27-pwm", .data = &imx_pwm_data_v2, },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx_pwm_dt_ids);
+
+static int imx_pwm_probe(struct platform_device *pdev)
+{
+ const struct of_device_id *of_id =
+ of_match_device(imx_pwm_dt_ids, &pdev->dev);
+ const struct imx_pwm_data *data;
+ struct imx_chip *imx;
+ struct resource *r;
+ int ret = 0;
+
+ if (!of_id)
+ return -ENODEV;
+
+ data = of_id->data;
+
+ imx = devm_kzalloc(&pdev->dev, sizeof(*imx), GFP_KERNEL);
+ if (imx == NULL)
+ return -ENOMEM;
+
+ imx->clk_per = devm_clk_get(&pdev->dev, "per");
+ if (IS_ERR(imx->clk_per)) {
+ dev_err(&pdev->dev, "getting per clock failed with %ld\n",
+ PTR_ERR(imx->clk_per));
+ return PTR_ERR(imx->clk_per);
+ }
+
+ imx->chip.ops = data->ops;
+ imx->chip.dev = &pdev->dev;
+ imx->chip.base = -1;
+ imx->chip.npwm = 1;
+
+ if (data->polarity_supported) {
+ dev_dbg(&pdev->dev, "PWM supports output inversion\n");
+ imx->chip.of_xlate = of_pwm_xlate_with_flags;
+ imx->chip.of_pwm_n_cells = 3;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ imx->mmio_base = devm_ioremap_resource(&pdev->dev, r);
+ if (IS_ERR(imx->mmio_base))
+ return PTR_ERR(imx->mmio_base);
+
+ ret = pwmchip_add(&imx->chip);
+ if (ret < 0)
+ return ret;
+
+ platform_set_drvdata(pdev, imx);
+ return 0;
+}
+
+static int imx_pwm_remove(struct platform_device *pdev)
+{
+ struct imx_chip *imx;
+
+ imx = platform_get_drvdata(pdev);
+ if (imx == NULL)
+ return -ENODEV;
+
+ return pwmchip_remove(&imx->chip);
+}
+
+static struct platform_driver imx_pwm_driver = {
+ .driver = {
+ .name = "imx-pwm",
+ .of_match_table = imx_pwm_dt_ids,
+ },
+ .probe = imx_pwm_probe,
+ .remove = imx_pwm_remove,
+};
+
+module_platform_driver(imx_pwm_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de>");