v4.19.13 snapshot.
diff --git a/drivers/ide/sc1200.c b/drivers/ide/sc1200.c
new file mode 100644
index 0000000..a5b7018
--- /dev/null
+++ b/drivers/ide/sc1200.c
@@ -0,0 +1,355 @@
+/*
+ * Copyright (C) 2000-2002 Mark Lord <mlord@pobox.com>
+ * Copyright (C) 2007 Bartlomiej Zolnierkiewicz
+ *
+ * May be copied or modified under the terms of the GNU General Public License
+ *
+ * Development of this chipset driver was funded
+ * by the nice folks at National Semiconductor.
+ *
+ * Documentation:
+ * Available from National Semiconductor
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/ide.h>
+#include <linux/pm.h>
+
+#include <asm/io.h>
+
+#define DRV_NAME "sc1200"
+
+#define SC1200_REV_A 0x00
+#define SC1200_REV_B1 0x01
+#define SC1200_REV_B3 0x02
+#define SC1200_REV_C1 0x03
+#define SC1200_REV_D1 0x04
+
+#define PCI_CLK_33 0x00
+#define PCI_CLK_48 0x01
+#define PCI_CLK_66 0x02
+#define PCI_CLK_33A 0x03
+
+static unsigned short sc1200_get_pci_clock (void)
+{
+ unsigned char chip_id, silicon_revision;
+ unsigned int pci_clock;
+ /*
+ * Check the silicon revision, as not all versions of the chip
+ * have the register with the fast PCI bus timings.
+ */
+ chip_id = inb (0x903c);
+ silicon_revision = inb (0x903d);
+
+ // Read the fast pci clock frequency
+ if (chip_id == 0x04 && silicon_revision < SC1200_REV_B1) {
+ pci_clock = PCI_CLK_33;
+ } else {
+ // check clock generator configuration (cfcc)
+ // the clock is in bits 8 and 9 of this word
+
+ pci_clock = inw (0x901e);
+ pci_clock >>= 8;
+ pci_clock &= 0x03;
+ if (pci_clock == PCI_CLK_33A)
+ pci_clock = PCI_CLK_33;
+ }
+ return pci_clock;
+}
+
+/*
+ * Here are the standard PIO mode 0-4 timings for each "format".
+ * Format-0 uses fast data reg timings, with slower command reg timings.
+ * Format-1 uses fast timings for all registers, but won't work with all drives.
+ */
+static const unsigned int sc1200_pio_timings[4][5] =
+ {{0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010}, // format0 33Mhz
+ {0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010}, // format1, 33Mhz
+ {0xfaa3f4f3, 0xc23232b2, 0x513101c1, 0x31213121, 0x10211021}, // format1, 48Mhz
+ {0xfff4fff4, 0xf35353d3, 0x814102f1, 0x42314231, 0x11311131}}; // format1, 66Mhz
+
+/*
+ * After chip reset, the PIO timings are set to 0x00009172, which is not valid.
+ */
+//#define SC1200_BAD_PIO(timings) (((timings)&~0x80000000)==0x00009172)
+
+static void sc1200_tunepio(ide_drive_t *drive, u8 pio)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *pdev = to_pci_dev(hwif->dev);
+ unsigned int basereg = hwif->channel ? 0x50 : 0x40, format = 0;
+
+ pci_read_config_dword(pdev, basereg + 4, &format);
+ format = (format >> 31) & 1;
+ if (format)
+ format += sc1200_get_pci_clock();
+ pci_write_config_dword(pdev, basereg + ((drive->dn & 1) << 3),
+ sc1200_pio_timings[format][pio]);
+}
+
+/*
+ * The SC1200 specifies that two drives sharing a cable cannot mix
+ * UDMA/MDMA. It has to be one or the other, for the pair, though
+ * different timings can still be chosen for each drive. We could
+ * set the appropriate timing bits on the fly, but that might be
+ * a bit confusing. So, for now we statically handle this requirement
+ * by looking at our mate drive to see what it is capable of, before
+ * choosing a mode for our own drive.
+ */
+static u8 sc1200_udma_filter(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ ide_drive_t *mate = ide_get_pair_dev(drive);
+ u16 *mateid;
+ u8 mask = hwif->ultra_mask;
+
+ if (mate == NULL)
+ goto out;
+ mateid = mate->id;
+
+ if (ata_id_has_dma(mateid) && __ide_dma_bad_drive(mate) == 0) {
+ if ((mateid[ATA_ID_FIELD_VALID] & 4) &&
+ (mateid[ATA_ID_UDMA_MODES] & 7))
+ goto out;
+ if (mateid[ATA_ID_MWDMA_MODES] & 7)
+ mask = 0;
+ }
+out:
+ return mask;
+}
+
+static void sc1200_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ unsigned int reg, timings;
+ unsigned short pci_clock;
+ unsigned int basereg = hwif->channel ? 0x50 : 0x40;
+ const u8 mode = drive->dma_mode;
+
+ static const u32 udma_timing[3][3] = {
+ { 0x00921250, 0x00911140, 0x00911030 },
+ { 0x00932470, 0x00922260, 0x00922140 },
+ { 0x009436a1, 0x00933481, 0x00923261 },
+ };
+
+ static const u32 mwdma_timing[3][3] = {
+ { 0x00077771, 0x00012121, 0x00002020 },
+ { 0x000bbbb2, 0x00024241, 0x00013131 },
+ { 0x000ffff3, 0x00035352, 0x00015151 },
+ };
+
+ pci_clock = sc1200_get_pci_clock();
+
+ /*
+ * Note that each DMA mode has several timings associated with it.
+ * The correct timing depends on the fast PCI clock freq.
+ */
+
+ if (mode >= XFER_UDMA_0)
+ timings = udma_timing[pci_clock][mode - XFER_UDMA_0];
+ else
+ timings = mwdma_timing[pci_clock][mode - XFER_MW_DMA_0];
+
+ if ((drive->dn & 1) == 0) {
+ pci_read_config_dword(dev, basereg + 4, ®);
+ timings |= reg & 0x80000000; /* preserve PIO format bit */
+ pci_write_config_dword(dev, basereg + 4, timings);
+ } else
+ pci_write_config_dword(dev, basereg + 12, timings);
+}
+
+/* Replacement for the standard ide_dma_end action in
+ * dma_proc.
+ *
+ * returns 1 on error, 0 otherwise
+ */
+static int sc1200_dma_end(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ unsigned long dma_base = hwif->dma_base;
+ u8 dma_stat;
+
+ dma_stat = inb(dma_base+2); /* get DMA status */
+
+ if (!(dma_stat & 4))
+ printk(" ide_dma_end dma_stat=%0x err=%x newerr=%x\n",
+ dma_stat, ((dma_stat&7)!=4), ((dma_stat&2)==2));
+
+ outb(dma_stat|0x1b, dma_base+2); /* clear the INTR & ERROR bits */
+ outb(inb(dma_base)&~1, dma_base); /* !! DO THIS HERE !! stop DMA */
+
+ return (dma_stat & 7) != 4; /* verify good DMA status */
+}
+
+/*
+ * sc1200_set_pio_mode() handles setting of PIO modes
+ * for both the chipset and drive.
+ *
+ * All existing BIOSs for this chipset guarantee that all drives
+ * will have valid default PIO timings set up before we get here.
+ */
+
+static void sc1200_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+ int mode = -1;
+ const u8 pio = drive->pio_mode - XFER_PIO_0;
+
+ /*
+ * bad abuse of ->set_pio_mode interface
+ */
+ switch (pio) {
+ case 200: mode = XFER_UDMA_0; break;
+ case 201: mode = XFER_UDMA_1; break;
+ case 202: mode = XFER_UDMA_2; break;
+ case 100: mode = XFER_MW_DMA_0; break;
+ case 101: mode = XFER_MW_DMA_1; break;
+ case 102: mode = XFER_MW_DMA_2; break;
+ }
+ if (mode != -1) {
+ printk("SC1200: %s: changing (U)DMA mode\n", drive->name);
+ ide_dma_off_quietly(drive);
+ if (ide_set_dma_mode(drive, mode) == 0 &&
+ (drive->dev_flags & IDE_DFLAG_USING_DMA))
+ hwif->dma_ops->dma_host_set(drive, 1);
+ return;
+ }
+
+ sc1200_tunepio(drive, pio);
+}
+
+#ifdef CONFIG_PM
+struct sc1200_saved_state {
+ u32 regs[8];
+};
+
+static int sc1200_suspend (struct pci_dev *dev, pm_message_t state)
+{
+ printk("SC1200: suspend(%u)\n", state.event);
+
+ /*
+ * we only save state when going from full power to less
+ */
+ if (state.event == PM_EVENT_ON) {
+ struct ide_host *host = pci_get_drvdata(dev);
+ struct sc1200_saved_state *ss = host->host_priv;
+ unsigned int r;
+
+ /*
+ * save timing registers
+ * (this may be unnecessary if BIOS also does it)
+ */
+ for (r = 0; r < 8; r++)
+ pci_read_config_dword(dev, 0x40 + r * 4, &ss->regs[r]);
+ }
+
+ pci_disable_device(dev);
+ pci_set_power_state(dev, pci_choose_state(dev, state));
+ return 0;
+}
+
+static int sc1200_resume (struct pci_dev *dev)
+{
+ struct ide_host *host = pci_get_drvdata(dev);
+ struct sc1200_saved_state *ss = host->host_priv;
+ unsigned int r;
+ int i;
+
+ i = pci_enable_device(dev);
+ if (i)
+ return i;
+
+ /*
+ * restore timing registers
+ * (this may be unnecessary if BIOS also does it)
+ */
+ for (r = 0; r < 8; r++)
+ pci_write_config_dword(dev, 0x40 + r * 4, ss->regs[r]);
+
+ return 0;
+}
+#endif
+
+static const struct ide_port_ops sc1200_port_ops = {
+ .set_pio_mode = sc1200_set_pio_mode,
+ .set_dma_mode = sc1200_set_dma_mode,
+ .udma_filter = sc1200_udma_filter,
+};
+
+static const struct ide_dma_ops sc1200_dma_ops = {
+ .dma_host_set = ide_dma_host_set,
+ .dma_setup = ide_dma_setup,
+ .dma_start = ide_dma_start,
+ .dma_end = sc1200_dma_end,
+ .dma_test_irq = ide_dma_test_irq,
+ .dma_lost_irq = ide_dma_lost_irq,
+ .dma_timer_expiry = ide_dma_sff_timer_expiry,
+ .dma_sff_read_status = ide_dma_sff_read_status,
+};
+
+static const struct ide_port_info sc1200_chipset = {
+ .name = DRV_NAME,
+ .port_ops = &sc1200_port_ops,
+ .dma_ops = &sc1200_dma_ops,
+ .host_flags = IDE_HFLAG_SERIALIZE |
+ IDE_HFLAG_POST_SET_MODE |
+ IDE_HFLAG_ABUSE_DMA_MODES,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
+};
+
+static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+ struct sc1200_saved_state *ss = NULL;
+ int rc;
+
+#ifdef CONFIG_PM
+ ss = kmalloc(sizeof(*ss), GFP_KERNEL);
+ if (ss == NULL)
+ return -ENOMEM;
+#endif
+ rc = ide_pci_init_one(dev, &sc1200_chipset, ss);
+ if (rc)
+ kfree(ss);
+
+ return rc;
+}
+
+static const struct pci_device_id sc1200_pci_tbl[] = {
+ { PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_SCx200_IDE), 0},
+ { 0, },
+};
+MODULE_DEVICE_TABLE(pci, sc1200_pci_tbl);
+
+static struct pci_driver sc1200_pci_driver = {
+ .name = "SC1200_IDE",
+ .id_table = sc1200_pci_tbl,
+ .probe = sc1200_init_one,
+ .remove = ide_pci_remove,
+#ifdef CONFIG_PM
+ .suspend = sc1200_suspend,
+ .resume = sc1200_resume,
+#endif
+};
+
+static int __init sc1200_ide_init(void)
+{
+ return ide_pci_register_driver(&sc1200_pci_driver);
+}
+
+static void __exit sc1200_ide_exit(void)
+{
+ pci_unregister_driver(&sc1200_pci_driver);
+}
+
+module_init(sc1200_ide_init);
+module_exit(sc1200_ide_exit);
+
+MODULE_AUTHOR("Mark Lord");
+MODULE_DESCRIPTION("PCI driver module for NS SC1200 IDE");
+MODULE_LICENSE("GPL");