diff --git a/Documentation/virtual/00-INDEX b/Documentation/virtual/00-INDEX
new file mode 100644
index 0000000..af0d239
--- /dev/null
+++ b/Documentation/virtual/00-INDEX
@@ -0,0 +1,11 @@
+Virtualization support in the Linux kernel.
+
+00-INDEX
+	- this file.
+
+paravirt_ops.txt
+	- Describes the Linux kernel pv_ops to support different hypervisors
+kvm/
+	- Kernel Virtual Machine.  See also http://linux-kvm.org
+uml/
+	- User Mode Linux, builds/runs Linux kernel as a userspace program.
diff --git a/Documentation/virtual/kvm/00-INDEX b/Documentation/virtual/kvm/00-INDEX
new file mode 100644
index 0000000..3492458
--- /dev/null
+++ b/Documentation/virtual/kvm/00-INDEX
@@ -0,0 +1,35 @@
+00-INDEX
+	- this file.
+amd-memory-encryption.rst
+	- notes on AMD Secure Encrypted Virtualization feature and SEV firmware
+	  command description
+api.txt
+	- KVM userspace API.
+arm
+	- internal ABI between the kernel and HYP (for arm/arm64)
+cpuid.txt
+	- KVM-specific cpuid leaves (x86).
+devices/
+	- KVM_CAP_DEVICE_CTRL userspace API.
+halt-polling.txt
+	- notes on halt-polling
+hypercalls.txt
+	- KVM hypercalls.
+locking.txt
+	- notes on KVM locks.
+mmu.txt
+	- the x86 kvm shadow mmu.
+msr.txt
+	- KVM-specific MSRs (x86).
+nested-vmx.txt
+	- notes on nested virtualization for Intel x86 processors.
+ppc-pv.txt
+	- the paravirtualization interface on PowerPC.
+review-checklist.txt
+	- review checklist for KVM patches.
+s390-diag.txt
+	- Diagnose hypercall description (for IBM S/390)
+timekeeping.txt
+	- timekeeping virtualization for x86-based architectures.
+vcpu-requests.rst
+	- internal VCPU request API
diff --git a/Documentation/virtual/kvm/amd-memory-encryption.rst b/Documentation/virtual/kvm/amd-memory-encryption.rst
new file mode 100644
index 0000000..71d6d25
--- /dev/null
+++ b/Documentation/virtual/kvm/amd-memory-encryption.rst
@@ -0,0 +1,247 @@
+======================================
+Secure Encrypted Virtualization (SEV)
+======================================
+
+Overview
+========
+
+Secure Encrypted Virtualization (SEV) is a feature found on AMD processors.
+
+SEV is an extension to the AMD-V architecture which supports running
+virtual machines (VMs) under the control of a hypervisor. When enabled,
+the memory contents of a VM will be transparently encrypted with a key
+unique to that VM.
+
+The hypervisor can determine the SEV support through the CPUID
+instruction. The CPUID function 0x8000001f reports information related
+to SEV::
+
+	0x8000001f[eax]:
+			Bit[1] 	indicates support for SEV
+	    ...
+		  [ecx]:
+			Bits[31:0]  Number of encrypted guests supported simultaneously
+
+If support for SEV is present, MSR 0xc001_0010 (MSR_K8_SYSCFG) and MSR 0xc001_0015
+(MSR_K7_HWCR) can be used to determine if it can be enabled::
+
+	0xc001_0010:
+		Bit[23]	   1 = memory encryption can be enabled
+			   0 = memory encryption can not be enabled
+
+	0xc001_0015:
+		Bit[0]	   1 = memory encryption can be enabled
+			   0 = memory encryption can not be enabled
+
+When SEV support is available, it can be enabled in a specific VM by
+setting the SEV bit before executing VMRUN.::
+
+	VMCB[0x90]:
+		Bit[1]	    1 = SEV is enabled
+			    0 = SEV is disabled
+
+SEV hardware uses ASIDs to associate a memory encryption key with a VM.
+Hence, the ASID for the SEV-enabled guests must be from 1 to a maximum value
+defined in the CPUID 0x8000001f[ecx] field.
+
+SEV Key Management
+==================
+
+The SEV guest key management is handled by a separate processor called the AMD
+Secure Processor (AMD-SP). Firmware running inside the AMD-SP provides a secure
+key management interface to perform common hypervisor activities such as
+encrypting bootstrap code, snapshot, migrating and debugging the guest. For more
+information, see the SEV Key Management spec [api-spec]_
+
+KVM implements the following commands to support common lifecycle events of SEV
+guests, such as launching, running, snapshotting, migrating and decommissioning.
+
+1. KVM_SEV_INIT
+---------------
+
+The KVM_SEV_INIT command is used by the hypervisor to initialize the SEV platform
+context. In a typical workflow, this command should be the first command issued.
+
+Returns: 0 on success, -negative on error
+
+2. KVM_SEV_LAUNCH_START
+-----------------------
+
+The KVM_SEV_LAUNCH_START command is used for creating the memory encryption
+context. To create the encryption context, user must provide a guest policy,
+the owner's public Diffie-Hellman (PDH) key and session information.
+
+Parameters: struct  kvm_sev_launch_start (in/out)
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_start {
+                __u32 handle;           /* if zero then firmware creates a new handle */
+                __u32 policy;           /* guest's policy */
+
+                __u64 dh_uaddr;         /* userspace address pointing to the guest owner's PDH key */
+                __u32 dh_len;
+
+                __u64 session_addr;     /* userspace address which points to the guest session information */
+                __u32 session_len;
+        };
+
+On success, the 'handle' field contains a new handle and on error, a negative value.
+
+For more details, see SEV spec Section 6.2.
+
+3. KVM_SEV_LAUNCH_UPDATE_DATA
+-----------------------------
+
+The KVM_SEV_LAUNCH_UPDATE_DATA is used for encrypting a memory region. It also
+calculates a measurement of the memory contents. The measurement is a signature
+of the memory contents that can be sent to the guest owner as an attestation
+that the memory was encrypted correctly by the firmware.
+
+Parameters (in): struct  kvm_sev_launch_update_data
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_update {
+                __u64 uaddr;    /* userspace address to be encrypted (must be 16-byte aligned) */
+                __u32 len;      /* length of the data to be encrypted (must be 16-byte aligned) */
+        };
+
+For more details, see SEV spec Section 6.3.
+
+4. KVM_SEV_LAUNCH_MEASURE
+-------------------------
+
+The KVM_SEV_LAUNCH_MEASURE command is used to retrieve the measurement of the
+data encrypted by the KVM_SEV_LAUNCH_UPDATE_DATA command. The guest owner may
+wait to provide the guest with confidential information until it can verify the
+measurement. Since the guest owner knows the initial contents of the guest at
+boot, the measurement can be verified by comparing it to what the guest owner
+expects.
+
+Parameters (in): struct  kvm_sev_launch_measure
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_measure {
+                __u64 uaddr;    /* where to copy the measurement */
+                __u32 len;      /* length of measurement blob */
+        };
+
+For more details on the measurement verification flow, see SEV spec Section 6.4.
+
+5. KVM_SEV_LAUNCH_FINISH
+------------------------
+
+After completion of the launch flow, the KVM_SEV_LAUNCH_FINISH command can be
+issued to make the guest ready for the execution.
+
+Returns: 0 on success, -negative on error
+
+6. KVM_SEV_GUEST_STATUS
+-----------------------
+
+The KVM_SEV_GUEST_STATUS command is used to retrieve status information about a
+SEV-enabled guest.
+
+Parameters (out): struct kvm_sev_guest_status
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_guest_status {
+                __u32 handle;   /* guest handle */
+                __u32 policy;   /* guest policy */
+                __u8 state;     /* guest state (see enum below) */
+        };
+
+SEV guest state:
+
+::
+
+        enum {
+        SEV_STATE_INVALID = 0;
+        SEV_STATE_LAUNCHING,    /* guest is currently being launched */
+        SEV_STATE_SECRET,       /* guest is being launched and ready to accept the ciphertext data */
+        SEV_STATE_RUNNING,      /* guest is fully launched and running */
+        SEV_STATE_RECEIVING,    /* guest is being migrated in from another SEV machine */
+        SEV_STATE_SENDING       /* guest is getting migrated out to another SEV machine */
+        };
+
+7. KVM_SEV_DBG_DECRYPT
+----------------------
+
+The KVM_SEV_DEBUG_DECRYPT command can be used by the hypervisor to request the
+firmware to decrypt the data at the given memory region.
+
+Parameters (in): struct kvm_sev_dbg
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_dbg {
+                __u64 src_uaddr;        /* userspace address of data to decrypt */
+                __u64 dst_uaddr;        /* userspace address of destination */
+                __u32 len;              /* length of memory region to decrypt */
+        };
+
+The command returns an error if the guest policy does not allow debugging.
+
+8. KVM_SEV_DBG_ENCRYPT
+----------------------
+
+The KVM_SEV_DEBUG_ENCRYPT command can be used by the hypervisor to request the
+firmware to encrypt the data at the given memory region.
+
+Parameters (in): struct kvm_sev_dbg
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_dbg {
+                __u64 src_uaddr;        /* userspace address of data to encrypt */
+                __u64 dst_uaddr;        /* userspace address of destination */
+                __u32 len;              /* length of memory region to encrypt */
+        };
+
+The command returns an error if the guest policy does not allow debugging.
+
+9. KVM_SEV_LAUNCH_SECRET
+------------------------
+
+The KVM_SEV_LAUNCH_SECRET command can be used by the hypervisor to inject secret
+data after the measurement has been validated by the guest owner.
+
+Parameters (in): struct kvm_sev_launch_secret
+
+Returns: 0 on success, -negative on error
+
+::
+
+        struct kvm_sev_launch_secret {
+                __u64 hdr_uaddr;        /* userspace address containing the packet header */
+                __u32 hdr_len;
+
+                __u64 guest_uaddr;      /* the guest memory region where the secret should be injected */
+                __u32 guest_len;
+
+                __u64 trans_uaddr;      /* the hypervisor memory region which contains the secret */
+                __u32 trans_len;
+        };
+
+References
+==========
+
+.. [white-paper] http://amd-dev.wpengine.netdna-cdn.com/wordpress/media/2013/12/AMD_Memory_Encryption_Whitepaper_v7-Public.pdf
+.. [api-spec] http://support.amd.com/TechDocs/55766_SEV-KM%20API_Specification.pdf
+.. [amd-apm] http://support.amd.com/TechDocs/24593.pdf (section 15.34)
+.. [kvm-forum]  http://www.linux-kvm.org/images/7/74/02x08A-Thomas_Lendacky-AMDs_Virtualizatoin_Memory_Encryption_Technology.pdf
diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt
new file mode 100644
index 0000000..647f941
--- /dev/null
+++ b/Documentation/virtual/kvm/api.txt
@@ -0,0 +1,4774 @@
+The Definitive KVM (Kernel-based Virtual Machine) API Documentation
+===================================================================
+
+1. General description
+----------------------
+
+The kvm API is a set of ioctls that are issued to control various aspects
+of a virtual machine.  The ioctls belong to three classes
+
+ - System ioctls: These query and set global attributes which affect the
+   whole kvm subsystem.  In addition a system ioctl is used to create
+   virtual machines
+
+ - VM ioctls: These query and set attributes that affect an entire virtual
+   machine, for example memory layout.  In addition a VM ioctl is used to
+   create virtual cpus (vcpus).
+
+   Only run VM ioctls from the same process (address space) that was used
+   to create the VM.
+
+ - vcpu ioctls: These query and set attributes that control the operation
+   of a single virtual cpu.
+
+   Only run vcpu ioctls from the same thread that was used to create the
+   vcpu.
+
+
+2. File descriptors
+-------------------
+
+The kvm API is centered around file descriptors.  An initial
+open("/dev/kvm") obtains a handle to the kvm subsystem; this handle
+can be used to issue system ioctls.  A KVM_CREATE_VM ioctl on this
+handle will create a VM file descriptor which can be used to issue VM
+ioctls.  A KVM_CREATE_VCPU ioctl on a VM fd will create a virtual cpu
+and return a file descriptor pointing to it.  Finally, ioctls on a vcpu
+fd can be used to control the vcpu, including the important task of
+actually running guest code.
+
+In general file descriptors can be migrated among processes by means
+of fork() and the SCM_RIGHTS facility of unix domain socket.  These
+kinds of tricks are explicitly not supported by kvm.  While they will
+not cause harm to the host, their actual behavior is not guaranteed by
+the API.  The only supported use is one virtual machine per process,
+and one vcpu per thread.
+
+
+3. Extensions
+-------------
+
+As of Linux 2.6.22, the KVM ABI has been stabilized: no backward
+incompatible change are allowed.  However, there is an extension
+facility that allows backward-compatible extensions to the API to be
+queried and used.
+
+The extension mechanism is not based on the Linux version number.
+Instead, kvm defines extension identifiers and a facility to query
+whether a particular extension identifier is available.  If it is, a
+set of ioctls is available for application use.
+
+
+4. API description
+------------------
+
+This section describes ioctls that can be used to control kvm guests.
+For each ioctl, the following information is provided along with a
+description:
+
+  Capability: which KVM extension provides this ioctl.  Can be 'basic',
+      which means that is will be provided by any kernel that supports
+      API version 12 (see section 4.1), a KVM_CAP_xyz constant, which
+      means availability needs to be checked with KVM_CHECK_EXTENSION
+      (see section 4.4), or 'none' which means that while not all kernels
+      support this ioctl, there's no capability bit to check its
+      availability: for kernels that don't support the ioctl,
+      the ioctl returns -ENOTTY.
+
+  Architectures: which instruction set architectures provide this ioctl.
+      x86 includes both i386 and x86_64.
+
+  Type: system, vm, or vcpu.
+
+  Parameters: what parameters are accepted by the ioctl.
+
+  Returns: the return value.  General error numbers (EBADF, ENOMEM, EINVAL)
+      are not detailed, but errors with specific meanings are.
+
+
+4.1 KVM_GET_API_VERSION
+
+Capability: basic
+Architectures: all
+Type: system ioctl
+Parameters: none
+Returns: the constant KVM_API_VERSION (=12)
+
+This identifies the API version as the stable kvm API. It is not
+expected that this number will change.  However, Linux 2.6.20 and
+2.6.21 report earlier versions; these are not documented and not
+supported.  Applications should refuse to run if KVM_GET_API_VERSION
+returns a value other than 12.  If this check passes, all ioctls
+described as 'basic' will be available.
+
+
+4.2 KVM_CREATE_VM
+
+Capability: basic
+Architectures: all
+Type: system ioctl
+Parameters: machine type identifier (KVM_VM_*)
+Returns: a VM fd that can be used to control the new virtual machine.
+
+The new VM has no virtual cpus and no memory.
+You probably want to use 0 as machine type.
+
+In order to create user controlled virtual machines on S390, check
+KVM_CAP_S390_UCONTROL and use the flag KVM_VM_S390_UCONTROL as
+privileged user (CAP_SYS_ADMIN).
+
+To use hardware assisted virtualization on MIPS (VZ ASE) rather than
+the default trap & emulate implementation (which changes the virtual
+memory layout to fit in user mode), check KVM_CAP_MIPS_VZ and use the
+flag KVM_VM_MIPS_VZ.
+
+
+4.3 KVM_GET_MSR_INDEX_LIST, KVM_GET_MSR_FEATURE_INDEX_LIST
+
+Capability: basic, KVM_CAP_GET_MSR_FEATURES for KVM_GET_MSR_FEATURE_INDEX_LIST
+Architectures: x86
+Type: system ioctl
+Parameters: struct kvm_msr_list (in/out)
+Returns: 0 on success; -1 on error
+Errors:
+  EFAULT:    the msr index list cannot be read from or written to
+  E2BIG:     the msr index list is to be to fit in the array specified by
+             the user.
+
+struct kvm_msr_list {
+	__u32 nmsrs; /* number of msrs in entries */
+	__u32 indices[0];
+};
+
+The user fills in the size of the indices array in nmsrs, and in return
+kvm adjusts nmsrs to reflect the actual number of msrs and fills in the
+indices array with their numbers.
+
+KVM_GET_MSR_INDEX_LIST returns the guest msrs that are supported.  The list
+varies by kvm version and host processor, but does not change otherwise.
+
+Note: if kvm indicates supports MCE (KVM_CAP_MCE), then the MCE bank MSRs are
+not returned in the MSR list, as different vcpus can have a different number
+of banks, as set via the KVM_X86_SETUP_MCE ioctl.
+
+KVM_GET_MSR_FEATURE_INDEX_LIST returns the list of MSRs that can be passed
+to the KVM_GET_MSRS system ioctl.  This lets userspace probe host capabilities
+and processor features that are exposed via MSRs (e.g., VMX capabilities).
+This list also varies by kvm version and host processor, but does not change
+otherwise.
+
+
+4.4 KVM_CHECK_EXTENSION
+
+Capability: basic, KVM_CAP_CHECK_EXTENSION_VM for vm ioctl
+Architectures: all
+Type: system ioctl, vm ioctl
+Parameters: extension identifier (KVM_CAP_*)
+Returns: 0 if unsupported; 1 (or some other positive integer) if supported
+
+The API allows the application to query about extensions to the core
+kvm API.  Userspace passes an extension identifier (an integer) and
+receives an integer that describes the extension availability.
+Generally 0 means no and 1 means yes, but some extensions may report
+additional information in the integer return value.
+
+Based on their initialization different VMs may have different capabilities.
+It is thus encouraged to use the vm ioctl to query for capabilities (available
+with KVM_CAP_CHECK_EXTENSION_VM on the vm fd)
+
+4.5 KVM_GET_VCPU_MMAP_SIZE
+
+Capability: basic
+Architectures: all
+Type: system ioctl
+Parameters: none
+Returns: size of vcpu mmap area, in bytes
+
+The KVM_RUN ioctl (cf.) communicates with userspace via a shared
+memory region.  This ioctl returns the size of that region.  See the
+KVM_RUN documentation for details.
+
+
+4.6 KVM_SET_MEMORY_REGION
+
+Capability: basic
+Architectures: all
+Type: vm ioctl
+Parameters: struct kvm_memory_region (in)
+Returns: 0 on success, -1 on error
+
+This ioctl is obsolete and has been removed.
+
+
+4.7 KVM_CREATE_VCPU
+
+Capability: basic
+Architectures: all
+Type: vm ioctl
+Parameters: vcpu id (apic id on x86)
+Returns: vcpu fd on success, -1 on error
+
+This API adds a vcpu to a virtual machine. No more than max_vcpus may be added.
+The vcpu id is an integer in the range [0, max_vcpu_id).
+
+The recommended max_vcpus value can be retrieved using the KVM_CAP_NR_VCPUS of
+the KVM_CHECK_EXTENSION ioctl() at run-time.
+The maximum possible value for max_vcpus can be retrieved using the
+KVM_CAP_MAX_VCPUS of the KVM_CHECK_EXTENSION ioctl() at run-time.
+
+If the KVM_CAP_NR_VCPUS does not exist, you should assume that max_vcpus is 4
+cpus max.
+If the KVM_CAP_MAX_VCPUS does not exist, you should assume that max_vcpus is
+same as the value returned from KVM_CAP_NR_VCPUS.
+
+The maximum possible value for max_vcpu_id can be retrieved using the
+KVM_CAP_MAX_VCPU_ID of the KVM_CHECK_EXTENSION ioctl() at run-time.
+
+If the KVM_CAP_MAX_VCPU_ID does not exist, you should assume that max_vcpu_id
+is the same as the value returned from KVM_CAP_MAX_VCPUS.
+
+On powerpc using book3s_hv mode, the vcpus are mapped onto virtual
+threads in one or more virtual CPU cores.  (This is because the
+hardware requires all the hardware threads in a CPU core to be in the
+same partition.)  The KVM_CAP_PPC_SMT capability indicates the number
+of vcpus per virtual core (vcore).  The vcore id is obtained by
+dividing the vcpu id by the number of vcpus per vcore.  The vcpus in a
+given vcore will always be in the same physical core as each other
+(though that might be a different physical core from time to time).
+Userspace can control the threading (SMT) mode of the guest by its
+allocation of vcpu ids.  For example, if userspace wants
+single-threaded guest vcpus, it should make all vcpu ids be a multiple
+of the number of vcpus per vcore.
+
+For virtual cpus that have been created with S390 user controlled virtual
+machines, the resulting vcpu fd can be memory mapped at page offset
+KVM_S390_SIE_PAGE_OFFSET in order to obtain a memory map of the virtual
+cpu's hardware control block.
+
+
+4.8 KVM_GET_DIRTY_LOG (vm ioctl)
+
+Capability: basic
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_dirty_log (in/out)
+Returns: 0 on success, -1 on error
+
+/* for KVM_GET_DIRTY_LOG */
+struct kvm_dirty_log {
+	__u32 slot;
+	__u32 padding;
+	union {
+		void __user *dirty_bitmap; /* one bit per page */
+		__u64 padding;
+	};
+};
+
+Given a memory slot, return a bitmap containing any pages dirtied
+since the last call to this ioctl.  Bit 0 is the first page in the
+memory slot.  Ensure the entire structure is cleared to avoid padding
+issues.
+
+If KVM_CAP_MULTI_ADDRESS_SPACE is available, bits 16-31 specifies
+the address space for which you want to return the dirty bitmap.
+They must be less than the value that KVM_CHECK_EXTENSION returns for
+the KVM_CAP_MULTI_ADDRESS_SPACE capability.
+
+
+4.9 KVM_SET_MEMORY_ALIAS
+
+Capability: basic
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_memory_alias (in)
+Returns: 0 (success), -1 (error)
+
+This ioctl is obsolete and has been removed.
+
+
+4.10 KVM_RUN
+
+Capability: basic
+Architectures: all
+Type: vcpu ioctl
+Parameters: none
+Returns: 0 on success, -1 on error
+Errors:
+  EINTR:     an unmasked signal is pending
+
+This ioctl is used to run a guest virtual cpu.  While there are no
+explicit parameters, there is an implicit parameter block that can be
+obtained by mmap()ing the vcpu fd at offset 0, with the size given by
+KVM_GET_VCPU_MMAP_SIZE.  The parameter block is formatted as a 'struct
+kvm_run' (see below).
+
+
+4.11 KVM_GET_REGS
+
+Capability: basic
+Architectures: all except ARM, arm64
+Type: vcpu ioctl
+Parameters: struct kvm_regs (out)
+Returns: 0 on success, -1 on error
+
+Reads the general purpose registers from the vcpu.
+
+/* x86 */
+struct kvm_regs {
+	/* out (KVM_GET_REGS) / in (KVM_SET_REGS) */
+	__u64 rax, rbx, rcx, rdx;
+	__u64 rsi, rdi, rsp, rbp;
+	__u64 r8,  r9,  r10, r11;
+	__u64 r12, r13, r14, r15;
+	__u64 rip, rflags;
+};
+
+/* mips */
+struct kvm_regs {
+	/* out (KVM_GET_REGS) / in (KVM_SET_REGS) */
+	__u64 gpr[32];
+	__u64 hi;
+	__u64 lo;
+	__u64 pc;
+};
+
+
+4.12 KVM_SET_REGS
+
+Capability: basic
+Architectures: all except ARM, arm64
+Type: vcpu ioctl
+Parameters: struct kvm_regs (in)
+Returns: 0 on success, -1 on error
+
+Writes the general purpose registers into the vcpu.
+
+See KVM_GET_REGS for the data structure.
+
+
+4.13 KVM_GET_SREGS
+
+Capability: basic
+Architectures: x86, ppc
+Type: vcpu ioctl
+Parameters: struct kvm_sregs (out)
+Returns: 0 on success, -1 on error
+
+Reads special registers from the vcpu.
+
+/* x86 */
+struct kvm_sregs {
+	struct kvm_segment cs, ds, es, fs, gs, ss;
+	struct kvm_segment tr, ldt;
+	struct kvm_dtable gdt, idt;
+	__u64 cr0, cr2, cr3, cr4, cr8;
+	__u64 efer;
+	__u64 apic_base;
+	__u64 interrupt_bitmap[(KVM_NR_INTERRUPTS + 63) / 64];
+};
+
+/* ppc -- see arch/powerpc/include/uapi/asm/kvm.h */
+
+interrupt_bitmap is a bitmap of pending external interrupts.  At most
+one bit may be set.  This interrupt has been acknowledged by the APIC
+but not yet injected into the cpu core.
+
+
+4.14 KVM_SET_SREGS
+
+Capability: basic
+Architectures: x86, ppc
+Type: vcpu ioctl
+Parameters: struct kvm_sregs (in)
+Returns: 0 on success, -1 on error
+
+Writes special registers into the vcpu.  See KVM_GET_SREGS for the
+data structures.
+
+
+4.15 KVM_TRANSLATE
+
+Capability: basic
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_translation (in/out)
+Returns: 0 on success, -1 on error
+
+Translates a virtual address according to the vcpu's current address
+translation mode.
+
+struct kvm_translation {
+	/* in */
+	__u64 linear_address;
+
+	/* out */
+	__u64 physical_address;
+	__u8  valid;
+	__u8  writeable;
+	__u8  usermode;
+	__u8  pad[5];
+};
+
+
+4.16 KVM_INTERRUPT
+
+Capability: basic
+Architectures: x86, ppc, mips
+Type: vcpu ioctl
+Parameters: struct kvm_interrupt (in)
+Returns: 0 on success, negative on failure.
+
+Queues a hardware interrupt vector to be injected.
+
+/* for KVM_INTERRUPT */
+struct kvm_interrupt {
+	/* in */
+	__u32 irq;
+};
+
+X86:
+
+Returns: 0 on success,
+	 -EEXIST if an interrupt is already enqueued
+	 -EINVAL the the irq number is invalid
+	 -ENXIO if the PIC is in the kernel
+	 -EFAULT if the pointer is invalid
+
+Note 'irq' is an interrupt vector, not an interrupt pin or line. This
+ioctl is useful if the in-kernel PIC is not used.
+
+PPC:
+
+Queues an external interrupt to be injected. This ioctl is overleaded
+with 3 different irq values:
+
+a) KVM_INTERRUPT_SET
+
+  This injects an edge type external interrupt into the guest once it's ready
+  to receive interrupts. When injected, the interrupt is done.
+
+b) KVM_INTERRUPT_UNSET
+
+  This unsets any pending interrupt.
+
+  Only available with KVM_CAP_PPC_UNSET_IRQ.
+
+c) KVM_INTERRUPT_SET_LEVEL
+
+  This injects a level type external interrupt into the guest context. The
+  interrupt stays pending until a specific ioctl with KVM_INTERRUPT_UNSET
+  is triggered.
+
+  Only available with KVM_CAP_PPC_IRQ_LEVEL.
+
+Note that any value for 'irq' other than the ones stated above is invalid
+and incurs unexpected behavior.
+
+MIPS:
+
+Queues an external interrupt to be injected into the virtual CPU. A negative
+interrupt number dequeues the interrupt.
+
+
+4.17 KVM_DEBUG_GUEST
+
+Capability: basic
+Architectures: none
+Type: vcpu ioctl
+Parameters: none)
+Returns: -1 on error
+
+Support for this has been removed.  Use KVM_SET_GUEST_DEBUG instead.
+
+
+4.18 KVM_GET_MSRS
+
+Capability: basic (vcpu), KVM_CAP_GET_MSR_FEATURES (system)
+Architectures: x86
+Type: system ioctl, vcpu ioctl
+Parameters: struct kvm_msrs (in/out)
+Returns: number of msrs successfully returned;
+        -1 on error
+
+When used as a system ioctl:
+Reads the values of MSR-based features that are available for the VM.  This
+is similar to KVM_GET_SUPPORTED_CPUID, but it returns MSR indices and values.
+The list of msr-based features can be obtained using KVM_GET_MSR_FEATURE_INDEX_LIST
+in a system ioctl.
+
+When used as a vcpu ioctl:
+Reads model-specific registers from the vcpu.  Supported msr indices can
+be obtained using KVM_GET_MSR_INDEX_LIST in a system ioctl.
+
+struct kvm_msrs {
+	__u32 nmsrs; /* number of msrs in entries */
+	__u32 pad;
+
+	struct kvm_msr_entry entries[0];
+};
+
+struct kvm_msr_entry {
+	__u32 index;
+	__u32 reserved;
+	__u64 data;
+};
+
+Application code should set the 'nmsrs' member (which indicates the
+size of the entries array) and the 'index' member of each array entry.
+kvm will fill in the 'data' member.
+
+
+4.19 KVM_SET_MSRS
+
+Capability: basic
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_msrs (in)
+Returns: 0 on success, -1 on error
+
+Writes model-specific registers to the vcpu.  See KVM_GET_MSRS for the
+data structures.
+
+Application code should set the 'nmsrs' member (which indicates the
+size of the entries array), and the 'index' and 'data' members of each
+array entry.
+
+
+4.20 KVM_SET_CPUID
+
+Capability: basic
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_cpuid (in)
+Returns: 0 on success, -1 on error
+
+Defines the vcpu responses to the cpuid instruction.  Applications
+should use the KVM_SET_CPUID2 ioctl if available.
+
+
+struct kvm_cpuid_entry {
+	__u32 function;
+	__u32 eax;
+	__u32 ebx;
+	__u32 ecx;
+	__u32 edx;
+	__u32 padding;
+};
+
+/* for KVM_SET_CPUID */
+struct kvm_cpuid {
+	__u32 nent;
+	__u32 padding;
+	struct kvm_cpuid_entry entries[0];
+};
+
+
+4.21 KVM_SET_SIGNAL_MASK
+
+Capability: basic
+Architectures: all
+Type: vcpu ioctl
+Parameters: struct kvm_signal_mask (in)
+Returns: 0 on success, -1 on error
+
+Defines which signals are blocked during execution of KVM_RUN.  This
+signal mask temporarily overrides the threads signal mask.  Any
+unblocked signal received (except SIGKILL and SIGSTOP, which retain
+their traditional behaviour) will cause KVM_RUN to return with -EINTR.
+
+Note the signal will only be delivered if not blocked by the original
+signal mask.
+
+/* for KVM_SET_SIGNAL_MASK */
+struct kvm_signal_mask {
+	__u32 len;
+	__u8  sigset[0];
+};
+
+
+4.22 KVM_GET_FPU
+
+Capability: basic
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_fpu (out)
+Returns: 0 on success, -1 on error
+
+Reads the floating point state from the vcpu.
+
+/* for KVM_GET_FPU and KVM_SET_FPU */
+struct kvm_fpu {
+	__u8  fpr[8][16];
+	__u16 fcw;
+	__u16 fsw;
+	__u8  ftwx;  /* in fxsave format */
+	__u8  pad1;
+	__u16 last_opcode;
+	__u64 last_ip;
+	__u64 last_dp;
+	__u8  xmm[16][16];
+	__u32 mxcsr;
+	__u32 pad2;
+};
+
+
+4.23 KVM_SET_FPU
+
+Capability: basic
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_fpu (in)
+Returns: 0 on success, -1 on error
+
+Writes the floating point state to the vcpu.
+
+/* for KVM_GET_FPU and KVM_SET_FPU */
+struct kvm_fpu {
+	__u8  fpr[8][16];
+	__u16 fcw;
+	__u16 fsw;
+	__u8  ftwx;  /* in fxsave format */
+	__u8  pad1;
+	__u16 last_opcode;
+	__u64 last_ip;
+	__u64 last_dp;
+	__u8  xmm[16][16];
+	__u32 mxcsr;
+	__u32 pad2;
+};
+
+
+4.24 KVM_CREATE_IRQCHIP
+
+Capability: KVM_CAP_IRQCHIP, KVM_CAP_S390_IRQCHIP (s390)
+Architectures: x86, ARM, arm64, s390
+Type: vm ioctl
+Parameters: none
+Returns: 0 on success, -1 on error
+
+Creates an interrupt controller model in the kernel.
+On x86, creates a virtual ioapic, a virtual PIC (two PICs, nested), and sets up
+future vcpus to have a local APIC.  IRQ routing for GSIs 0-15 is set to both
+PIC and IOAPIC; GSI 16-23 only go to the IOAPIC.
+On ARM/arm64, a GICv2 is created. Any other GIC versions require the usage of
+KVM_CREATE_DEVICE, which also supports creating a GICv2.  Using
+KVM_CREATE_DEVICE is preferred over KVM_CREATE_IRQCHIP for GICv2.
+On s390, a dummy irq routing table is created.
+
+Note that on s390 the KVM_CAP_S390_IRQCHIP vm capability needs to be enabled
+before KVM_CREATE_IRQCHIP can be used.
+
+
+4.25 KVM_IRQ_LINE
+
+Capability: KVM_CAP_IRQCHIP
+Architectures: x86, arm, arm64
+Type: vm ioctl
+Parameters: struct kvm_irq_level
+Returns: 0 on success, -1 on error
+
+Sets the level of a GSI input to the interrupt controller model in the kernel.
+On some architectures it is required that an interrupt controller model has
+been previously created with KVM_CREATE_IRQCHIP.  Note that edge-triggered
+interrupts require the level to be set to 1 and then back to 0.
+
+On real hardware, interrupt pins can be active-low or active-high.  This
+does not matter for the level field of struct kvm_irq_level: 1 always
+means active (asserted), 0 means inactive (deasserted).
+
+x86 allows the operating system to program the interrupt polarity
+(active-low/active-high) for level-triggered interrupts, and KVM used
+to consider the polarity.  However, due to bitrot in the handling of
+active-low interrupts, the above convention is now valid on x86 too.
+This is signaled by KVM_CAP_X86_IOAPIC_POLARITY_IGNORED.  Userspace
+should not present interrupts to the guest as active-low unless this
+capability is present (or unless it is not using the in-kernel irqchip,
+of course).
+
+
+ARM/arm64 can signal an interrupt either at the CPU level, or at the
+in-kernel irqchip (GIC), and for in-kernel irqchip can tell the GIC to
+use PPIs designated for specific cpus.  The irq field is interpreted
+like this:
+
+  bits:  | 31 ... 24 | 23  ... 16 | 15    ...    0 |
+  field: | irq_type  | vcpu_index |     irq_id     |
+
+The irq_type field has the following values:
+- irq_type[0]: out-of-kernel GIC: irq_id 0 is IRQ, irq_id 1 is FIQ
+- irq_type[1]: in-kernel GIC: SPI, irq_id between 32 and 1019 (incl.)
+               (the vcpu_index field is ignored)
+- irq_type[2]: in-kernel GIC: PPI, irq_id between 16 and 31 (incl.)
+
+(The irq_id field thus corresponds nicely to the IRQ ID in the ARM GIC specs)
+
+In both cases, level is used to assert/deassert the line.
+
+struct kvm_irq_level {
+	union {
+		__u32 irq;     /* GSI */
+		__s32 status;  /* not used for KVM_IRQ_LEVEL */
+	};
+	__u32 level;           /* 0 or 1 */
+};
+
+
+4.26 KVM_GET_IRQCHIP
+
+Capability: KVM_CAP_IRQCHIP
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_irqchip (in/out)
+Returns: 0 on success, -1 on error
+
+Reads the state of a kernel interrupt controller created with
+KVM_CREATE_IRQCHIP into a buffer provided by the caller.
+
+struct kvm_irqchip {
+	__u32 chip_id;  /* 0 = PIC1, 1 = PIC2, 2 = IOAPIC */
+	__u32 pad;
+        union {
+		char dummy[512];  /* reserving space */
+		struct kvm_pic_state pic;
+		struct kvm_ioapic_state ioapic;
+	} chip;
+};
+
+
+4.27 KVM_SET_IRQCHIP
+
+Capability: KVM_CAP_IRQCHIP
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_irqchip (in)
+Returns: 0 on success, -1 on error
+
+Sets the state of a kernel interrupt controller created with
+KVM_CREATE_IRQCHIP from a buffer provided by the caller.
+
+struct kvm_irqchip {
+	__u32 chip_id;  /* 0 = PIC1, 1 = PIC2, 2 = IOAPIC */
+	__u32 pad;
+        union {
+		char dummy[512];  /* reserving space */
+		struct kvm_pic_state pic;
+		struct kvm_ioapic_state ioapic;
+	} chip;
+};
+
+
+4.28 KVM_XEN_HVM_CONFIG
+
+Capability: KVM_CAP_XEN_HVM
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_xen_hvm_config (in)
+Returns: 0 on success, -1 on error
+
+Sets the MSR that the Xen HVM guest uses to initialize its hypercall
+page, and provides the starting address and size of the hypercall
+blobs in userspace.  When the guest writes the MSR, kvm copies one
+page of a blob (32- or 64-bit, depending on the vcpu mode) to guest
+memory.
+
+struct kvm_xen_hvm_config {
+	__u32 flags;
+	__u32 msr;
+	__u64 blob_addr_32;
+	__u64 blob_addr_64;
+	__u8 blob_size_32;
+	__u8 blob_size_64;
+	__u8 pad2[30];
+};
+
+
+4.29 KVM_GET_CLOCK
+
+Capability: KVM_CAP_ADJUST_CLOCK
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_clock_data (out)
+Returns: 0 on success, -1 on error
+
+Gets the current timestamp of kvmclock as seen by the current guest. In
+conjunction with KVM_SET_CLOCK, it is used to ensure monotonicity on scenarios
+such as migration.
+
+When KVM_CAP_ADJUST_CLOCK is passed to KVM_CHECK_EXTENSION, it returns the
+set of bits that KVM can return in struct kvm_clock_data's flag member.
+
+The only flag defined now is KVM_CLOCK_TSC_STABLE.  If set, the returned
+value is the exact kvmclock value seen by all VCPUs at the instant
+when KVM_GET_CLOCK was called.  If clear, the returned value is simply
+CLOCK_MONOTONIC plus a constant offset; the offset can be modified
+with KVM_SET_CLOCK.  KVM will try to make all VCPUs follow this clock,
+but the exact value read by each VCPU could differ, because the host
+TSC is not stable.
+
+struct kvm_clock_data {
+	__u64 clock;  /* kvmclock current value */
+	__u32 flags;
+	__u32 pad[9];
+};
+
+
+4.30 KVM_SET_CLOCK
+
+Capability: KVM_CAP_ADJUST_CLOCK
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_clock_data (in)
+Returns: 0 on success, -1 on error
+
+Sets the current timestamp of kvmclock to the value specified in its parameter.
+In conjunction with KVM_GET_CLOCK, it is used to ensure monotonicity on scenarios
+such as migration.
+
+struct kvm_clock_data {
+	__u64 clock;  /* kvmclock current value */
+	__u32 flags;
+	__u32 pad[9];
+};
+
+
+4.31 KVM_GET_VCPU_EVENTS
+
+Capability: KVM_CAP_VCPU_EVENTS
+Extended by: KVM_CAP_INTR_SHADOW
+Architectures: x86, arm, arm64
+Type: vcpu ioctl
+Parameters: struct kvm_vcpu_event (out)
+Returns: 0 on success, -1 on error
+
+X86:
+
+Gets currently pending exceptions, interrupts, and NMIs as well as related
+states of the vcpu.
+
+struct kvm_vcpu_events {
+	struct {
+		__u8 injected;
+		__u8 nr;
+		__u8 has_error_code;
+		__u8 pad;
+		__u32 error_code;
+	} exception;
+	struct {
+		__u8 injected;
+		__u8 nr;
+		__u8 soft;
+		__u8 shadow;
+	} interrupt;
+	struct {
+		__u8 injected;
+		__u8 pending;
+		__u8 masked;
+		__u8 pad;
+	} nmi;
+	__u32 sipi_vector;
+	__u32 flags;
+	struct {
+		__u8 smm;
+		__u8 pending;
+		__u8 smm_inside_nmi;
+		__u8 latched_init;
+	} smi;
+};
+
+Only two fields are defined in the flags field:
+
+- KVM_VCPUEVENT_VALID_SHADOW may be set in the flags field to signal that
+  interrupt.shadow contains a valid state.
+
+- KVM_VCPUEVENT_VALID_SMM may be set in the flags field to signal that
+  smi contains a valid state.
+
+ARM/ARM64:
+
+If the guest accesses a device that is being emulated by the host kernel in
+such a way that a real device would generate a physical SError, KVM may make
+a virtual SError pending for that VCPU. This system error interrupt remains
+pending until the guest takes the exception by unmasking PSTATE.A.
+
+Running the VCPU may cause it to take a pending SError, or make an access that
+causes an SError to become pending. The event's description is only valid while
+the VPCU is not running.
+
+This API provides a way to read and write the pending 'event' state that is not
+visible to the guest. To save, restore or migrate a VCPU the struct representing
+the state can be read then written using this GET/SET API, along with the other
+guest-visible registers. It is not possible to 'cancel' an SError that has been
+made pending.
+
+A device being emulated in user-space may also wish to generate an SError. To do
+this the events structure can be populated by user-space. The current state
+should be read first, to ensure no existing SError is pending. If an existing
+SError is pending, the architecture's 'Multiple SError interrupts' rules should
+be followed. (2.5.3 of DDI0587.a "ARM Reliability, Availability, and
+Serviceability (RAS) Specification").
+
+SError exceptions always have an ESR value. Some CPUs have the ability to
+specify what the virtual SError's ESR value should be. These systems will
+advertise KVM_CAP_ARM_INJECT_SERROR_ESR. In this case exception.has_esr will
+always have a non-zero value when read, and the agent making an SError pending
+should specify the ISS field in the lower 24 bits of exception.serror_esr. If
+the system supports KVM_CAP_ARM_INJECT_SERROR_ESR, but user-space sets the events
+with exception.has_esr as zero, KVM will choose an ESR.
+
+Specifying exception.has_esr on a system that does not support it will return
+-EINVAL. Setting anything other than the lower 24bits of exception.serror_esr
+will return -EINVAL.
+
+struct kvm_vcpu_events {
+	struct {
+		__u8 serror_pending;
+		__u8 serror_has_esr;
+		/* Align it to 8 bytes */
+		__u8 pad[6];
+		__u64 serror_esr;
+	} exception;
+	__u32 reserved[12];
+};
+
+4.32 KVM_SET_VCPU_EVENTS
+
+Capability: KVM_CAP_VCPU_EVENTS
+Extended by: KVM_CAP_INTR_SHADOW
+Architectures: x86, arm, arm64
+Type: vcpu ioctl
+Parameters: struct kvm_vcpu_event (in)
+Returns: 0 on success, -1 on error
+
+X86:
+
+Set pending exceptions, interrupts, and NMIs as well as related states of the
+vcpu.
+
+See KVM_GET_VCPU_EVENTS for the data structure.
+
+Fields that may be modified asynchronously by running VCPUs can be excluded
+from the update. These fields are nmi.pending, sipi_vector, smi.smm,
+smi.pending. Keep the corresponding bits in the flags field cleared to
+suppress overwriting the current in-kernel state. The bits are:
+
+KVM_VCPUEVENT_VALID_NMI_PENDING - transfer nmi.pending to the kernel
+KVM_VCPUEVENT_VALID_SIPI_VECTOR - transfer sipi_vector
+KVM_VCPUEVENT_VALID_SMM         - transfer the smi sub-struct.
+
+If KVM_CAP_INTR_SHADOW is available, KVM_VCPUEVENT_VALID_SHADOW can be set in
+the flags field to signal that interrupt.shadow contains a valid state and
+shall be written into the VCPU.
+
+KVM_VCPUEVENT_VALID_SMM can only be set if KVM_CAP_X86_SMM is available.
+
+ARM/ARM64:
+
+Set the pending SError exception state for this VCPU. It is not possible to
+'cancel' an Serror that has been made pending.
+
+See KVM_GET_VCPU_EVENTS for the data structure.
+
+
+4.33 KVM_GET_DEBUGREGS
+
+Capability: KVM_CAP_DEBUGREGS
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_debugregs (out)
+Returns: 0 on success, -1 on error
+
+Reads debug registers from the vcpu.
+
+struct kvm_debugregs {
+	__u64 db[4];
+	__u64 dr6;
+	__u64 dr7;
+	__u64 flags;
+	__u64 reserved[9];
+};
+
+
+4.34 KVM_SET_DEBUGREGS
+
+Capability: KVM_CAP_DEBUGREGS
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_debugregs (in)
+Returns: 0 on success, -1 on error
+
+Writes debug registers into the vcpu.
+
+See KVM_GET_DEBUGREGS for the data structure. The flags field is unused
+yet and must be cleared on entry.
+
+
+4.35 KVM_SET_USER_MEMORY_REGION
+
+Capability: KVM_CAP_USER_MEM
+Architectures: all
+Type: vm ioctl
+Parameters: struct kvm_userspace_memory_region (in)
+Returns: 0 on success, -1 on error
+
+struct kvm_userspace_memory_region {
+	__u32 slot;
+	__u32 flags;
+	__u64 guest_phys_addr;
+	__u64 memory_size; /* bytes */
+	__u64 userspace_addr; /* start of the userspace allocated memory */
+};
+
+/* for kvm_memory_region::flags */
+#define KVM_MEM_LOG_DIRTY_PAGES	(1UL << 0)
+#define KVM_MEM_READONLY	(1UL << 1)
+
+This ioctl allows the user to create or modify a guest physical memory
+slot.  When changing an existing slot, it may be moved in the guest
+physical memory space, or its flags may be modified.  It may not be
+resized.  Slots may not overlap in guest physical address space.
+Bits 0-15 of "slot" specifies the slot id and this value should be
+less than the maximum number of user memory slots supported per VM.
+The maximum allowed slots can be queried using KVM_CAP_NR_MEMSLOTS,
+if this capability is supported by the architecture.
+
+If KVM_CAP_MULTI_ADDRESS_SPACE is available, bits 16-31 of "slot"
+specifies the address space which is being modified.  They must be
+less than the value that KVM_CHECK_EXTENSION returns for the
+KVM_CAP_MULTI_ADDRESS_SPACE capability.  Slots in separate address spaces
+are unrelated; the restriction on overlapping slots only applies within
+each address space.
+
+Memory for the region is taken starting at the address denoted by the
+field userspace_addr, which must point at user addressable memory for
+the entire memory slot size.  Any object may back this memory, including
+anonymous memory, ordinary files, and hugetlbfs.
+
+It is recommended that the lower 21 bits of guest_phys_addr and userspace_addr
+be identical.  This allows large pages in the guest to be backed by large
+pages in the host.
+
+The flags field supports two flags: KVM_MEM_LOG_DIRTY_PAGES and
+KVM_MEM_READONLY.  The former can be set to instruct KVM to keep track of
+writes to memory within the slot.  See KVM_GET_DIRTY_LOG ioctl to know how to
+use it.  The latter can be set, if KVM_CAP_READONLY_MEM capability allows it,
+to make a new slot read-only.  In this case, writes to this memory will be
+posted to userspace as KVM_EXIT_MMIO exits.
+
+When the KVM_CAP_SYNC_MMU capability is available, changes in the backing of
+the memory region are automatically reflected into the guest.  For example, an
+mmap() that affects the region will be made visible immediately.  Another
+example is madvise(MADV_DROP).
+
+It is recommended to use this API instead of the KVM_SET_MEMORY_REGION ioctl.
+The KVM_SET_MEMORY_REGION does not allow fine grained control over memory
+allocation and is deprecated.
+
+
+4.36 KVM_SET_TSS_ADDR
+
+Capability: KVM_CAP_SET_TSS_ADDR
+Architectures: x86
+Type: vm ioctl
+Parameters: unsigned long tss_address (in)
+Returns: 0 on success, -1 on error
+
+This ioctl defines the physical address of a three-page region in the guest
+physical address space.  The region must be within the first 4GB of the
+guest physical address space and must not conflict with any memory slot
+or any mmio address.  The guest may malfunction if it accesses this memory
+region.
+
+This ioctl is required on Intel-based hosts.  This is needed on Intel hardware
+because of a quirk in the virtualization implementation (see the internals
+documentation when it pops into existence).
+
+
+4.37 KVM_ENABLE_CAP
+
+Capability: KVM_CAP_ENABLE_CAP, KVM_CAP_ENABLE_CAP_VM
+Architectures: x86 (only KVM_CAP_ENABLE_CAP_VM),
+	       mips (only KVM_CAP_ENABLE_CAP), ppc, s390
+Type: vcpu ioctl, vm ioctl (with KVM_CAP_ENABLE_CAP_VM)
+Parameters: struct kvm_enable_cap (in)
+Returns: 0 on success; -1 on error
+
++Not all extensions are enabled by default. Using this ioctl the application
+can enable an extension, making it available to the guest.
+
+On systems that do not support this ioctl, it always fails. On systems that
+do support it, it only works for extensions that are supported for enablement.
+
+To check if a capability can be enabled, the KVM_CHECK_EXTENSION ioctl should
+be used.
+
+struct kvm_enable_cap {
+       /* in */
+       __u32 cap;
+
+The capability that is supposed to get enabled.
+
+       __u32 flags;
+
+A bitfield indicating future enhancements. Has to be 0 for now.
+
+       __u64 args[4];
+
+Arguments for enabling a feature. If a feature needs initial values to
+function properly, this is the place to put them.
+
+       __u8  pad[64];
+};
+
+The vcpu ioctl should be used for vcpu-specific capabilities, the vm ioctl
+for vm-wide capabilities.
+
+4.38 KVM_GET_MP_STATE
+
+Capability: KVM_CAP_MP_STATE
+Architectures: x86, s390, arm, arm64
+Type: vcpu ioctl
+Parameters: struct kvm_mp_state (out)
+Returns: 0 on success; -1 on error
+
+struct kvm_mp_state {
+	__u32 mp_state;
+};
+
+Returns the vcpu's current "multiprocessing state" (though also valid on
+uniprocessor guests).
+
+Possible values are:
+
+ - KVM_MP_STATE_RUNNABLE:        the vcpu is currently running [x86,arm/arm64]
+ - KVM_MP_STATE_UNINITIALIZED:   the vcpu is an application processor (AP)
+                                 which has not yet received an INIT signal [x86]
+ - KVM_MP_STATE_INIT_RECEIVED:   the vcpu has received an INIT signal, and is
+                                 now ready for a SIPI [x86]
+ - KVM_MP_STATE_HALTED:          the vcpu has executed a HLT instruction and
+                                 is waiting for an interrupt [x86]
+ - KVM_MP_STATE_SIPI_RECEIVED:   the vcpu has just received a SIPI (vector
+                                 accessible via KVM_GET_VCPU_EVENTS) [x86]
+ - KVM_MP_STATE_STOPPED:         the vcpu is stopped [s390,arm/arm64]
+ - KVM_MP_STATE_CHECK_STOP:      the vcpu is in a special error state [s390]
+ - KVM_MP_STATE_OPERATING:       the vcpu is operating (running or halted)
+                                 [s390]
+ - KVM_MP_STATE_LOAD:            the vcpu is in a special load/startup state
+                                 [s390]
+
+On x86, this ioctl is only useful after KVM_CREATE_IRQCHIP. Without an
+in-kernel irqchip, the multiprocessing state must be maintained by userspace on
+these architectures.
+
+For arm/arm64:
+
+The only states that are valid are KVM_MP_STATE_STOPPED and
+KVM_MP_STATE_RUNNABLE which reflect if the vcpu is paused or not.
+
+4.39 KVM_SET_MP_STATE
+
+Capability: KVM_CAP_MP_STATE
+Architectures: x86, s390, arm, arm64
+Type: vcpu ioctl
+Parameters: struct kvm_mp_state (in)
+Returns: 0 on success; -1 on error
+
+Sets the vcpu's current "multiprocessing state"; see KVM_GET_MP_STATE for
+arguments.
+
+On x86, this ioctl is only useful after KVM_CREATE_IRQCHIP. Without an
+in-kernel irqchip, the multiprocessing state must be maintained by userspace on
+these architectures.
+
+For arm/arm64:
+
+The only states that are valid are KVM_MP_STATE_STOPPED and
+KVM_MP_STATE_RUNNABLE which reflect if the vcpu should be paused or not.
+
+4.40 KVM_SET_IDENTITY_MAP_ADDR
+
+Capability: KVM_CAP_SET_IDENTITY_MAP_ADDR
+Architectures: x86
+Type: vm ioctl
+Parameters: unsigned long identity (in)
+Returns: 0 on success, -1 on error
+
+This ioctl defines the physical address of a one-page region in the guest
+physical address space.  The region must be within the first 4GB of the
+guest physical address space and must not conflict with any memory slot
+or any mmio address.  The guest may malfunction if it accesses this memory
+region.
+
+Setting the address to 0 will result in resetting the address to its default
+(0xfffbc000).
+
+This ioctl is required on Intel-based hosts.  This is needed on Intel hardware
+because of a quirk in the virtualization implementation (see the internals
+documentation when it pops into existence).
+
+Fails if any VCPU has already been created.
+
+4.41 KVM_SET_BOOT_CPU_ID
+
+Capability: KVM_CAP_SET_BOOT_CPU_ID
+Architectures: x86
+Type: vm ioctl
+Parameters: unsigned long vcpu_id
+Returns: 0 on success, -1 on error
+
+Define which vcpu is the Bootstrap Processor (BSP).  Values are the same
+as the vcpu id in KVM_CREATE_VCPU.  If this ioctl is not called, the default
+is vcpu 0.
+
+
+4.42 KVM_GET_XSAVE
+
+Capability: KVM_CAP_XSAVE
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_xsave (out)
+Returns: 0 on success, -1 on error
+
+struct kvm_xsave {
+	__u32 region[1024];
+};
+
+This ioctl would copy current vcpu's xsave struct to the userspace.
+
+
+4.43 KVM_SET_XSAVE
+
+Capability: KVM_CAP_XSAVE
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_xsave (in)
+Returns: 0 on success, -1 on error
+
+struct kvm_xsave {
+	__u32 region[1024];
+};
+
+This ioctl would copy userspace's xsave struct to the kernel.
+
+
+4.44 KVM_GET_XCRS
+
+Capability: KVM_CAP_XCRS
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_xcrs (out)
+Returns: 0 on success, -1 on error
+
+struct kvm_xcr {
+	__u32 xcr;
+	__u32 reserved;
+	__u64 value;
+};
+
+struct kvm_xcrs {
+	__u32 nr_xcrs;
+	__u32 flags;
+	struct kvm_xcr xcrs[KVM_MAX_XCRS];
+	__u64 padding[16];
+};
+
+This ioctl would copy current vcpu's xcrs to the userspace.
+
+
+4.45 KVM_SET_XCRS
+
+Capability: KVM_CAP_XCRS
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_xcrs (in)
+Returns: 0 on success, -1 on error
+
+struct kvm_xcr {
+	__u32 xcr;
+	__u32 reserved;
+	__u64 value;
+};
+
+struct kvm_xcrs {
+	__u32 nr_xcrs;
+	__u32 flags;
+	struct kvm_xcr xcrs[KVM_MAX_XCRS];
+	__u64 padding[16];
+};
+
+This ioctl would set vcpu's xcr to the value userspace specified.
+
+
+4.46 KVM_GET_SUPPORTED_CPUID
+
+Capability: KVM_CAP_EXT_CPUID
+Architectures: x86
+Type: system ioctl
+Parameters: struct kvm_cpuid2 (in/out)
+Returns: 0 on success, -1 on error
+
+struct kvm_cpuid2 {
+	__u32 nent;
+	__u32 padding;
+	struct kvm_cpuid_entry2 entries[0];
+};
+
+#define KVM_CPUID_FLAG_SIGNIFCANT_INDEX		BIT(0)
+#define KVM_CPUID_FLAG_STATEFUL_FUNC		BIT(1)
+#define KVM_CPUID_FLAG_STATE_READ_NEXT		BIT(2)
+
+struct kvm_cpuid_entry2 {
+	__u32 function;
+	__u32 index;
+	__u32 flags;
+	__u32 eax;
+	__u32 ebx;
+	__u32 ecx;
+	__u32 edx;
+	__u32 padding[3];
+};
+
+This ioctl returns x86 cpuid features which are supported by both the
+hardware and kvm in its default configuration.  Userspace can use the
+information returned by this ioctl to construct cpuid information (for
+KVM_SET_CPUID2) that is consistent with hardware, kernel, and
+userspace capabilities, and with user requirements (for example, the
+user may wish to constrain cpuid to emulate older hardware, or for
+feature consistency across a cluster).
+
+Note that certain capabilities, such as KVM_CAP_X86_DISABLE_EXITS, may
+expose cpuid features (e.g. MONITOR) which are not supported by kvm in
+its default configuration. If userspace enables such capabilities, it
+is responsible for modifying the results of this ioctl appropriately.
+
+Userspace invokes KVM_GET_SUPPORTED_CPUID by passing a kvm_cpuid2 structure
+with the 'nent' field indicating the number of entries in the variable-size
+array 'entries'.  If the number of entries is too low to describe the cpu
+capabilities, an error (E2BIG) is returned.  If the number is too high,
+the 'nent' field is adjusted and an error (ENOMEM) is returned.  If the
+number is just right, the 'nent' field is adjusted to the number of valid
+entries in the 'entries' array, which is then filled.
+
+The entries returned are the host cpuid as returned by the cpuid instruction,
+with unknown or unsupported features masked out.  Some features (for example,
+x2apic), may not be present in the host cpu, but are exposed by kvm if it can
+emulate them efficiently. The fields in each entry are defined as follows:
+
+  function: the eax value used to obtain the entry
+  index: the ecx value used to obtain the entry (for entries that are
+         affected by ecx)
+  flags: an OR of zero or more of the following:
+        KVM_CPUID_FLAG_SIGNIFCANT_INDEX:
+           if the index field is valid
+        KVM_CPUID_FLAG_STATEFUL_FUNC:
+           if cpuid for this function returns different values for successive
+           invocations; there will be several entries with the same function,
+           all with this flag set
+        KVM_CPUID_FLAG_STATE_READ_NEXT:
+           for KVM_CPUID_FLAG_STATEFUL_FUNC entries, set if this entry is
+           the first entry to be read by a cpu
+   eax, ebx, ecx, edx: the values returned by the cpuid instruction for
+         this function/index combination
+
+The TSC deadline timer feature (CPUID leaf 1, ecx[24]) is always returned
+as false, since the feature depends on KVM_CREATE_IRQCHIP for local APIC
+support.  Instead it is reported via
+
+  ioctl(KVM_CHECK_EXTENSION, KVM_CAP_TSC_DEADLINE_TIMER)
+
+if that returns true and you use KVM_CREATE_IRQCHIP, or if you emulate the
+feature in userspace, then you can enable the feature for KVM_SET_CPUID2.
+
+
+4.47 KVM_PPC_GET_PVINFO
+
+Capability: KVM_CAP_PPC_GET_PVINFO
+Architectures: ppc
+Type: vm ioctl
+Parameters: struct kvm_ppc_pvinfo (out)
+Returns: 0 on success, !0 on error
+
+struct kvm_ppc_pvinfo {
+	__u32 flags;
+	__u32 hcall[4];
+	__u8  pad[108];
+};
+
+This ioctl fetches PV specific information that need to be passed to the guest
+using the device tree or other means from vm context.
+
+The hcall array defines 4 instructions that make up a hypercall.
+
+If any additional field gets added to this structure later on, a bit for that
+additional piece of information will be set in the flags bitmap.
+
+The flags bitmap is defined as:
+
+   /* the host supports the ePAPR idle hcall
+   #define KVM_PPC_PVINFO_FLAGS_EV_IDLE   (1<<0)
+
+4.52 KVM_SET_GSI_ROUTING
+
+Capability: KVM_CAP_IRQ_ROUTING
+Architectures: x86 s390 arm arm64
+Type: vm ioctl
+Parameters: struct kvm_irq_routing (in)
+Returns: 0 on success, -1 on error
+
+Sets the GSI routing table entries, overwriting any previously set entries.
+
+On arm/arm64, GSI routing has the following limitation:
+- GSI routing does not apply to KVM_IRQ_LINE but only to KVM_IRQFD.
+
+struct kvm_irq_routing {
+	__u32 nr;
+	__u32 flags;
+	struct kvm_irq_routing_entry entries[0];
+};
+
+No flags are specified so far, the corresponding field must be set to zero.
+
+struct kvm_irq_routing_entry {
+	__u32 gsi;
+	__u32 type;
+	__u32 flags;
+	__u32 pad;
+	union {
+		struct kvm_irq_routing_irqchip irqchip;
+		struct kvm_irq_routing_msi msi;
+		struct kvm_irq_routing_s390_adapter adapter;
+		struct kvm_irq_routing_hv_sint hv_sint;
+		__u32 pad[8];
+	} u;
+};
+
+/* gsi routing entry types */
+#define KVM_IRQ_ROUTING_IRQCHIP 1
+#define KVM_IRQ_ROUTING_MSI 2
+#define KVM_IRQ_ROUTING_S390_ADAPTER 3
+#define KVM_IRQ_ROUTING_HV_SINT 4
+
+flags:
+- KVM_MSI_VALID_DEVID: used along with KVM_IRQ_ROUTING_MSI routing entry
+  type, specifies that the devid field contains a valid value.  The per-VM
+  KVM_CAP_MSI_DEVID capability advertises the requirement to provide
+  the device ID.  If this capability is not available, userspace should
+  never set the KVM_MSI_VALID_DEVID flag as the ioctl might fail.
+- zero otherwise
+
+struct kvm_irq_routing_irqchip {
+	__u32 irqchip;
+	__u32 pin;
+};
+
+struct kvm_irq_routing_msi {
+	__u32 address_lo;
+	__u32 address_hi;
+	__u32 data;
+	union {
+		__u32 pad;
+		__u32 devid;
+	};
+};
+
+If KVM_MSI_VALID_DEVID is set, devid contains a unique device identifier
+for the device that wrote the MSI message.  For PCI, this is usually a
+BFD identifier in the lower 16 bits.
+
+On x86, address_hi is ignored unless the KVM_X2APIC_API_USE_32BIT_IDS
+feature of KVM_CAP_X2APIC_API capability is enabled.  If it is enabled,
+address_hi bits 31-8 provide bits 31-8 of the destination id.  Bits 7-0 of
+address_hi must be zero.
+
+struct kvm_irq_routing_s390_adapter {
+	__u64 ind_addr;
+	__u64 summary_addr;
+	__u64 ind_offset;
+	__u32 summary_offset;
+	__u32 adapter_id;
+};
+
+struct kvm_irq_routing_hv_sint {
+	__u32 vcpu;
+	__u32 sint;
+};
+
+
+4.55 KVM_SET_TSC_KHZ
+
+Capability: KVM_CAP_TSC_CONTROL
+Architectures: x86
+Type: vcpu ioctl
+Parameters: virtual tsc_khz
+Returns: 0 on success, -1 on error
+
+Specifies the tsc frequency for the virtual machine. The unit of the
+frequency is KHz.
+
+
+4.56 KVM_GET_TSC_KHZ
+
+Capability: KVM_CAP_GET_TSC_KHZ
+Architectures: x86
+Type: vcpu ioctl
+Parameters: none
+Returns: virtual tsc-khz on success, negative value on error
+
+Returns the tsc frequency of the guest. The unit of the return value is
+KHz. If the host has unstable tsc this ioctl returns -EIO instead as an
+error.
+
+
+4.57 KVM_GET_LAPIC
+
+Capability: KVM_CAP_IRQCHIP
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_lapic_state (out)
+Returns: 0 on success, -1 on error
+
+#define KVM_APIC_REG_SIZE 0x400
+struct kvm_lapic_state {
+	char regs[KVM_APIC_REG_SIZE];
+};
+
+Reads the Local APIC registers and copies them into the input argument.  The
+data format and layout are the same as documented in the architecture manual.
+
+If KVM_X2APIC_API_USE_32BIT_IDS feature of KVM_CAP_X2APIC_API is
+enabled, then the format of APIC_ID register depends on the APIC mode
+(reported by MSR_IA32_APICBASE) of its VCPU.  x2APIC stores APIC ID in
+the APIC_ID register (bytes 32-35).  xAPIC only allows an 8-bit APIC ID
+which is stored in bits 31-24 of the APIC register, or equivalently in
+byte 35 of struct kvm_lapic_state's regs field.  KVM_GET_LAPIC must then
+be called after MSR_IA32_APICBASE has been set with KVM_SET_MSR.
+
+If KVM_X2APIC_API_USE_32BIT_IDS feature is disabled, struct kvm_lapic_state
+always uses xAPIC format.
+
+
+4.58 KVM_SET_LAPIC
+
+Capability: KVM_CAP_IRQCHIP
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_lapic_state (in)
+Returns: 0 on success, -1 on error
+
+#define KVM_APIC_REG_SIZE 0x400
+struct kvm_lapic_state {
+	char regs[KVM_APIC_REG_SIZE];
+};
+
+Copies the input argument into the Local APIC registers.  The data format
+and layout are the same as documented in the architecture manual.
+
+The format of the APIC ID register (bytes 32-35 of struct kvm_lapic_state's
+regs field) depends on the state of the KVM_CAP_X2APIC_API capability.
+See the note in KVM_GET_LAPIC.
+
+
+4.59 KVM_IOEVENTFD
+
+Capability: KVM_CAP_IOEVENTFD
+Architectures: all
+Type: vm ioctl
+Parameters: struct kvm_ioeventfd (in)
+Returns: 0 on success, !0 on error
+
+This ioctl attaches or detaches an ioeventfd to a legal pio/mmio address
+within the guest.  A guest write in the registered address will signal the
+provided event instead of triggering an exit.
+
+struct kvm_ioeventfd {
+	__u64 datamatch;
+	__u64 addr;        /* legal pio/mmio address */
+	__u32 len;         /* 0, 1, 2, 4, or 8 bytes    */
+	__s32 fd;
+	__u32 flags;
+	__u8  pad[36];
+};
+
+For the special case of virtio-ccw devices on s390, the ioevent is matched
+to a subchannel/virtqueue tuple instead.
+
+The following flags are defined:
+
+#define KVM_IOEVENTFD_FLAG_DATAMATCH (1 << kvm_ioeventfd_flag_nr_datamatch)
+#define KVM_IOEVENTFD_FLAG_PIO       (1 << kvm_ioeventfd_flag_nr_pio)
+#define KVM_IOEVENTFD_FLAG_DEASSIGN  (1 << kvm_ioeventfd_flag_nr_deassign)
+#define KVM_IOEVENTFD_FLAG_VIRTIO_CCW_NOTIFY \
+	(1 << kvm_ioeventfd_flag_nr_virtio_ccw_notify)
+
+If datamatch flag is set, the event will be signaled only if the written value
+to the registered address is equal to datamatch in struct kvm_ioeventfd.
+
+For virtio-ccw devices, addr contains the subchannel id and datamatch the
+virtqueue index.
+
+With KVM_CAP_IOEVENTFD_ANY_LENGTH, a zero length ioeventfd is allowed, and
+the kernel will ignore the length of guest write and may get a faster vmexit.
+The speedup may only apply to specific architectures, but the ioeventfd will
+work anyway.
+
+4.60 KVM_DIRTY_TLB
+
+Capability: KVM_CAP_SW_TLB
+Architectures: ppc
+Type: vcpu ioctl
+Parameters: struct kvm_dirty_tlb (in)
+Returns: 0 on success, -1 on error
+
+struct kvm_dirty_tlb {
+	__u64 bitmap;
+	__u32 num_dirty;
+};
+
+This must be called whenever userspace has changed an entry in the shared
+TLB, prior to calling KVM_RUN on the associated vcpu.
+
+The "bitmap" field is the userspace address of an array.  This array
+consists of a number of bits, equal to the total number of TLB entries as
+determined by the last successful call to KVM_CONFIG_TLB, rounded up to the
+nearest multiple of 64.
+
+Each bit corresponds to one TLB entry, ordered the same as in the shared TLB
+array.
+
+The array is little-endian: the bit 0 is the least significant bit of the
+first byte, bit 8 is the least significant bit of the second byte, etc.
+This avoids any complications with differing word sizes.
+
+The "num_dirty" field is a performance hint for KVM to determine whether it
+should skip processing the bitmap and just invalidate everything.  It must
+be set to the number of set bits in the bitmap.
+
+
+4.62 KVM_CREATE_SPAPR_TCE
+
+Capability: KVM_CAP_SPAPR_TCE
+Architectures: powerpc
+Type: vm ioctl
+Parameters: struct kvm_create_spapr_tce (in)
+Returns: file descriptor for manipulating the created TCE table
+
+This creates a virtual TCE (translation control entry) table, which
+is an IOMMU for PAPR-style virtual I/O.  It is used to translate
+logical addresses used in virtual I/O into guest physical addresses,
+and provides a scatter/gather capability for PAPR virtual I/O.
+
+/* for KVM_CAP_SPAPR_TCE */
+struct kvm_create_spapr_tce {
+	__u64 liobn;
+	__u32 window_size;
+};
+
+The liobn field gives the logical IO bus number for which to create a
+TCE table.  The window_size field specifies the size of the DMA window
+which this TCE table will translate - the table will contain one 64
+bit TCE entry for every 4kiB of the DMA window.
+
+When the guest issues an H_PUT_TCE hcall on a liobn for which a TCE
+table has been created using this ioctl(), the kernel will handle it
+in real mode, updating the TCE table.  H_PUT_TCE calls for other
+liobns will cause a vm exit and must be handled by userspace.
+
+The return value is a file descriptor which can be passed to mmap(2)
+to map the created TCE table into userspace.  This lets userspace read
+the entries written by kernel-handled H_PUT_TCE calls, and also lets
+userspace update the TCE table directly which is useful in some
+circumstances.
+
+
+4.63 KVM_ALLOCATE_RMA
+
+Capability: KVM_CAP_PPC_RMA
+Architectures: powerpc
+Type: vm ioctl
+Parameters: struct kvm_allocate_rma (out)
+Returns: file descriptor for mapping the allocated RMA
+
+This allocates a Real Mode Area (RMA) from the pool allocated at boot
+time by the kernel.  An RMA is a physically-contiguous, aligned region
+of memory used on older POWER processors to provide the memory which
+will be accessed by real-mode (MMU off) accesses in a KVM guest.
+POWER processors support a set of sizes for the RMA that usually
+includes 64MB, 128MB, 256MB and some larger powers of two.
+
+/* for KVM_ALLOCATE_RMA */
+struct kvm_allocate_rma {
+	__u64 rma_size;
+};
+
+The return value is a file descriptor which can be passed to mmap(2)
+to map the allocated RMA into userspace.  The mapped area can then be
+passed to the KVM_SET_USER_MEMORY_REGION ioctl to establish it as the
+RMA for a virtual machine.  The size of the RMA in bytes (which is
+fixed at host kernel boot time) is returned in the rma_size field of
+the argument structure.
+
+The KVM_CAP_PPC_RMA capability is 1 or 2 if the KVM_ALLOCATE_RMA ioctl
+is supported; 2 if the processor requires all virtual machines to have
+an RMA, or 1 if the processor can use an RMA but doesn't require it,
+because it supports the Virtual RMA (VRMA) facility.
+
+
+4.64 KVM_NMI
+
+Capability: KVM_CAP_USER_NMI
+Architectures: x86
+Type: vcpu ioctl
+Parameters: none
+Returns: 0 on success, -1 on error
+
+Queues an NMI on the thread's vcpu.  Note this is well defined only
+when KVM_CREATE_IRQCHIP has not been called, since this is an interface
+between the virtual cpu core and virtual local APIC.  After KVM_CREATE_IRQCHIP
+has been called, this interface is completely emulated within the kernel.
+
+To use this to emulate the LINT1 input with KVM_CREATE_IRQCHIP, use the
+following algorithm:
+
+  - pause the vcpu
+  - read the local APIC's state (KVM_GET_LAPIC)
+  - check whether changing LINT1 will queue an NMI (see the LVT entry for LINT1)
+  - if so, issue KVM_NMI
+  - resume the vcpu
+
+Some guests configure the LINT1 NMI input to cause a panic, aiding in
+debugging.
+
+
+4.65 KVM_S390_UCAS_MAP
+
+Capability: KVM_CAP_S390_UCONTROL
+Architectures: s390
+Type: vcpu ioctl
+Parameters: struct kvm_s390_ucas_mapping (in)
+Returns: 0 in case of success
+
+The parameter is defined like this:
+	struct kvm_s390_ucas_mapping {
+		__u64 user_addr;
+		__u64 vcpu_addr;
+		__u64 length;
+	};
+
+This ioctl maps the memory at "user_addr" with the length "length" to
+the vcpu's address space starting at "vcpu_addr". All parameters need to
+be aligned by 1 megabyte.
+
+
+4.66 KVM_S390_UCAS_UNMAP
+
+Capability: KVM_CAP_S390_UCONTROL
+Architectures: s390
+Type: vcpu ioctl
+Parameters: struct kvm_s390_ucas_mapping (in)
+Returns: 0 in case of success
+
+The parameter is defined like this:
+	struct kvm_s390_ucas_mapping {
+		__u64 user_addr;
+		__u64 vcpu_addr;
+		__u64 length;
+	};
+
+This ioctl unmaps the memory in the vcpu's address space starting at
+"vcpu_addr" with the length "length". The field "user_addr" is ignored.
+All parameters need to be aligned by 1 megabyte.
+
+
+4.67 KVM_S390_VCPU_FAULT
+
+Capability: KVM_CAP_S390_UCONTROL
+Architectures: s390
+Type: vcpu ioctl
+Parameters: vcpu absolute address (in)
+Returns: 0 in case of success
+
+This call creates a page table entry on the virtual cpu's address space
+(for user controlled virtual machines) or the virtual machine's address
+space (for regular virtual machines). This only works for minor faults,
+thus it's recommended to access subject memory page via the user page
+table upfront. This is useful to handle validity intercepts for user
+controlled virtual machines to fault in the virtual cpu's lowcore pages
+prior to calling the KVM_RUN ioctl.
+
+
+4.68 KVM_SET_ONE_REG
+
+Capability: KVM_CAP_ONE_REG
+Architectures: all
+Type: vcpu ioctl
+Parameters: struct kvm_one_reg (in)
+Returns: 0 on success, negative value on failure
+
+struct kvm_one_reg {
+       __u64 id;
+       __u64 addr;
+};
+
+Using this ioctl, a single vcpu register can be set to a specific value
+defined by user space with the passed in struct kvm_one_reg, where id
+refers to the register identifier as described below and addr is a pointer
+to a variable with the respective size. There can be architecture agnostic
+and architecture specific registers. Each have their own range of operation
+and their own constants and width. To keep track of the implemented
+registers, find a list below:
+
+  Arch  |           Register            | Width (bits)
+        |                               |
+  PPC   | KVM_REG_PPC_HIOR              | 64
+  PPC   | KVM_REG_PPC_IAC1              | 64
+  PPC   | KVM_REG_PPC_IAC2              | 64
+  PPC   | KVM_REG_PPC_IAC3              | 64
+  PPC   | KVM_REG_PPC_IAC4              | 64
+  PPC   | KVM_REG_PPC_DAC1              | 64
+  PPC   | KVM_REG_PPC_DAC2              | 64
+  PPC   | KVM_REG_PPC_DABR              | 64
+  PPC   | KVM_REG_PPC_DSCR              | 64
+  PPC   | KVM_REG_PPC_PURR              | 64
+  PPC   | KVM_REG_PPC_SPURR             | 64
+  PPC   | KVM_REG_PPC_DAR               | 64
+  PPC   | KVM_REG_PPC_DSISR             | 32
+  PPC   | KVM_REG_PPC_AMR               | 64
+  PPC   | KVM_REG_PPC_UAMOR             | 64
+  PPC   | KVM_REG_PPC_MMCR0             | 64
+  PPC   | KVM_REG_PPC_MMCR1             | 64
+  PPC   | KVM_REG_PPC_MMCRA             | 64
+  PPC   | KVM_REG_PPC_MMCR2             | 64
+  PPC   | KVM_REG_PPC_MMCRS             | 64
+  PPC   | KVM_REG_PPC_SIAR              | 64
+  PPC   | KVM_REG_PPC_SDAR              | 64
+  PPC   | KVM_REG_PPC_SIER              | 64
+  PPC   | KVM_REG_PPC_PMC1              | 32
+  PPC   | KVM_REG_PPC_PMC2              | 32
+  PPC   | KVM_REG_PPC_PMC3              | 32
+  PPC   | KVM_REG_PPC_PMC4              | 32
+  PPC   | KVM_REG_PPC_PMC5              | 32
+  PPC   | KVM_REG_PPC_PMC6              | 32
+  PPC   | KVM_REG_PPC_PMC7              | 32
+  PPC   | KVM_REG_PPC_PMC8              | 32
+  PPC   | KVM_REG_PPC_FPR0              | 64
+          ...
+  PPC   | KVM_REG_PPC_FPR31             | 64
+  PPC   | KVM_REG_PPC_VR0               | 128
+          ...
+  PPC   | KVM_REG_PPC_VR31              | 128
+  PPC   | KVM_REG_PPC_VSR0              | 128
+          ...
+  PPC   | KVM_REG_PPC_VSR31             | 128
+  PPC   | KVM_REG_PPC_FPSCR             | 64
+  PPC   | KVM_REG_PPC_VSCR              | 32
+  PPC   | KVM_REG_PPC_VPA_ADDR          | 64
+  PPC   | KVM_REG_PPC_VPA_SLB           | 128
+  PPC   | KVM_REG_PPC_VPA_DTL           | 128
+  PPC   | KVM_REG_PPC_EPCR              | 32
+  PPC   | KVM_REG_PPC_EPR               | 32
+  PPC   | KVM_REG_PPC_TCR               | 32
+  PPC   | KVM_REG_PPC_TSR               | 32
+  PPC   | KVM_REG_PPC_OR_TSR            | 32
+  PPC   | KVM_REG_PPC_CLEAR_TSR         | 32
+  PPC   | KVM_REG_PPC_MAS0              | 32
+  PPC   | KVM_REG_PPC_MAS1              | 32
+  PPC   | KVM_REG_PPC_MAS2              | 64
+  PPC   | KVM_REG_PPC_MAS7_3            | 64
+  PPC   | KVM_REG_PPC_MAS4              | 32
+  PPC   | KVM_REG_PPC_MAS6              | 32
+  PPC   | KVM_REG_PPC_MMUCFG            | 32
+  PPC   | KVM_REG_PPC_TLB0CFG           | 32
+  PPC   | KVM_REG_PPC_TLB1CFG           | 32
+  PPC   | KVM_REG_PPC_TLB2CFG           | 32
+  PPC   | KVM_REG_PPC_TLB3CFG           | 32
+  PPC   | KVM_REG_PPC_TLB0PS            | 32
+  PPC   | KVM_REG_PPC_TLB1PS            | 32
+  PPC   | KVM_REG_PPC_TLB2PS            | 32
+  PPC   | KVM_REG_PPC_TLB3PS            | 32
+  PPC   | KVM_REG_PPC_EPTCFG            | 32
+  PPC   | KVM_REG_PPC_ICP_STATE         | 64
+  PPC   | KVM_REG_PPC_TB_OFFSET         | 64
+  PPC   | KVM_REG_PPC_SPMC1             | 32
+  PPC   | KVM_REG_PPC_SPMC2             | 32
+  PPC   | KVM_REG_PPC_IAMR              | 64
+  PPC   | KVM_REG_PPC_TFHAR             | 64
+  PPC   | KVM_REG_PPC_TFIAR             | 64
+  PPC   | KVM_REG_PPC_TEXASR            | 64
+  PPC   | KVM_REG_PPC_FSCR              | 64
+  PPC   | KVM_REG_PPC_PSPB              | 32
+  PPC   | KVM_REG_PPC_EBBHR             | 64
+  PPC   | KVM_REG_PPC_EBBRR             | 64
+  PPC   | KVM_REG_PPC_BESCR             | 64
+  PPC   | KVM_REG_PPC_TAR               | 64
+  PPC   | KVM_REG_PPC_DPDES             | 64
+  PPC   | KVM_REG_PPC_DAWR              | 64
+  PPC   | KVM_REG_PPC_DAWRX             | 64
+  PPC   | KVM_REG_PPC_CIABR             | 64
+  PPC   | KVM_REG_PPC_IC                | 64
+  PPC   | KVM_REG_PPC_VTB               | 64
+  PPC   | KVM_REG_PPC_CSIGR             | 64
+  PPC   | KVM_REG_PPC_TACR              | 64
+  PPC   | KVM_REG_PPC_TCSCR             | 64
+  PPC   | KVM_REG_PPC_PID               | 64
+  PPC   | KVM_REG_PPC_ACOP              | 64
+  PPC   | KVM_REG_PPC_VRSAVE            | 32
+  PPC   | KVM_REG_PPC_LPCR              | 32
+  PPC   | KVM_REG_PPC_LPCR_64           | 64
+  PPC   | KVM_REG_PPC_PPR               | 64
+  PPC   | KVM_REG_PPC_ARCH_COMPAT       | 32
+  PPC   | KVM_REG_PPC_DABRX             | 32
+  PPC   | KVM_REG_PPC_WORT              | 64
+  PPC	| KVM_REG_PPC_SPRG9             | 64
+  PPC	| KVM_REG_PPC_DBSR              | 32
+  PPC   | KVM_REG_PPC_TIDR              | 64
+  PPC   | KVM_REG_PPC_PSSCR             | 64
+  PPC   | KVM_REG_PPC_DEC_EXPIRY        | 64
+  PPC   | KVM_REG_PPC_TM_GPR0           | 64
+          ...
+  PPC   | KVM_REG_PPC_TM_GPR31          | 64
+  PPC   | KVM_REG_PPC_TM_VSR0           | 128
+          ...
+  PPC   | KVM_REG_PPC_TM_VSR63          | 128
+  PPC   | KVM_REG_PPC_TM_CR             | 64
+  PPC   | KVM_REG_PPC_TM_LR             | 64
+  PPC   | KVM_REG_PPC_TM_CTR            | 64
+  PPC   | KVM_REG_PPC_TM_FPSCR          | 64
+  PPC   | KVM_REG_PPC_TM_AMR            | 64
+  PPC   | KVM_REG_PPC_TM_PPR            | 64
+  PPC   | KVM_REG_PPC_TM_VRSAVE         | 64
+  PPC   | KVM_REG_PPC_TM_VSCR           | 32
+  PPC   | KVM_REG_PPC_TM_DSCR           | 64
+  PPC   | KVM_REG_PPC_TM_TAR            | 64
+  PPC   | KVM_REG_PPC_TM_XER            | 64
+        |                               |
+  MIPS  | KVM_REG_MIPS_R0               | 64
+          ...
+  MIPS  | KVM_REG_MIPS_R31              | 64
+  MIPS  | KVM_REG_MIPS_HI               | 64
+  MIPS  | KVM_REG_MIPS_LO               | 64
+  MIPS  | KVM_REG_MIPS_PC               | 64
+  MIPS  | KVM_REG_MIPS_CP0_INDEX        | 32
+  MIPS  | KVM_REG_MIPS_CP0_ENTRYLO0     | 64
+  MIPS  | KVM_REG_MIPS_CP0_ENTRYLO1     | 64
+  MIPS  | KVM_REG_MIPS_CP0_CONTEXT      | 64
+  MIPS  | KVM_REG_MIPS_CP0_CONTEXTCONFIG| 32
+  MIPS  | KVM_REG_MIPS_CP0_USERLOCAL    | 64
+  MIPS  | KVM_REG_MIPS_CP0_XCONTEXTCONFIG| 64
+  MIPS  | KVM_REG_MIPS_CP0_PAGEMASK     | 32
+  MIPS  | KVM_REG_MIPS_CP0_PAGEGRAIN    | 32
+  MIPS  | KVM_REG_MIPS_CP0_SEGCTL0      | 64
+  MIPS  | KVM_REG_MIPS_CP0_SEGCTL1      | 64
+  MIPS  | KVM_REG_MIPS_CP0_SEGCTL2      | 64
+  MIPS  | KVM_REG_MIPS_CP0_PWBASE       | 64
+  MIPS  | KVM_REG_MIPS_CP0_PWFIELD      | 64
+  MIPS  | KVM_REG_MIPS_CP0_PWSIZE       | 64
+  MIPS  | KVM_REG_MIPS_CP0_WIRED        | 32
+  MIPS  | KVM_REG_MIPS_CP0_PWCTL        | 32
+  MIPS  | KVM_REG_MIPS_CP0_HWRENA       | 32
+  MIPS  | KVM_REG_MIPS_CP0_BADVADDR     | 64
+  MIPS  | KVM_REG_MIPS_CP0_BADINSTR     | 32
+  MIPS  | KVM_REG_MIPS_CP0_BADINSTRP    | 32
+  MIPS  | KVM_REG_MIPS_CP0_COUNT        | 32
+  MIPS  | KVM_REG_MIPS_CP0_ENTRYHI      | 64
+  MIPS  | KVM_REG_MIPS_CP0_COMPARE      | 32
+  MIPS  | KVM_REG_MIPS_CP0_STATUS       | 32
+  MIPS  | KVM_REG_MIPS_CP0_INTCTL       | 32
+  MIPS  | KVM_REG_MIPS_CP0_CAUSE        | 32
+  MIPS  | KVM_REG_MIPS_CP0_EPC          | 64
+  MIPS  | KVM_REG_MIPS_CP0_PRID         | 32
+  MIPS  | KVM_REG_MIPS_CP0_EBASE        | 64
+  MIPS  | KVM_REG_MIPS_CP0_CONFIG       | 32
+  MIPS  | KVM_REG_MIPS_CP0_CONFIG1      | 32
+  MIPS  | KVM_REG_MIPS_CP0_CONFIG2      | 32
+  MIPS  | KVM_REG_MIPS_CP0_CONFIG3      | 32
+  MIPS  | KVM_REG_MIPS_CP0_CONFIG4      | 32
+  MIPS  | KVM_REG_MIPS_CP0_CONFIG5      | 32
+  MIPS  | KVM_REG_MIPS_CP0_CONFIG7      | 32
+  MIPS  | KVM_REG_MIPS_CP0_XCONTEXT     | 64
+  MIPS  | KVM_REG_MIPS_CP0_ERROREPC     | 64
+  MIPS  | KVM_REG_MIPS_CP0_KSCRATCH1    | 64
+  MIPS  | KVM_REG_MIPS_CP0_KSCRATCH2    | 64
+  MIPS  | KVM_REG_MIPS_CP0_KSCRATCH3    | 64
+  MIPS  | KVM_REG_MIPS_CP0_KSCRATCH4    | 64
+  MIPS  | KVM_REG_MIPS_CP0_KSCRATCH5    | 64
+  MIPS  | KVM_REG_MIPS_CP0_KSCRATCH6    | 64
+  MIPS  | KVM_REG_MIPS_CP0_MAAR(0..63)  | 64
+  MIPS  | KVM_REG_MIPS_COUNT_CTL        | 64
+  MIPS  | KVM_REG_MIPS_COUNT_RESUME     | 64
+  MIPS  | KVM_REG_MIPS_COUNT_HZ         | 64
+  MIPS  | KVM_REG_MIPS_FPR_32(0..31)    | 32
+  MIPS  | KVM_REG_MIPS_FPR_64(0..31)    | 64
+  MIPS  | KVM_REG_MIPS_VEC_128(0..31)   | 128
+  MIPS  | KVM_REG_MIPS_FCR_IR           | 32
+  MIPS  | KVM_REG_MIPS_FCR_CSR          | 32
+  MIPS  | KVM_REG_MIPS_MSA_IR           | 32
+  MIPS  | KVM_REG_MIPS_MSA_CSR          | 32
+
+ARM registers are mapped using the lower 32 bits.  The upper 16 of that
+is the register group type, or coprocessor number:
+
+ARM core registers have the following id bit patterns:
+  0x4020 0000 0010 <index into the kvm_regs struct:16>
+
+ARM 32-bit CP15 registers have the following id bit patterns:
+  0x4020 0000 000F <zero:1> <crn:4> <crm:4> <opc1:4> <opc2:3>
+
+ARM 64-bit CP15 registers have the following id bit patterns:
+  0x4030 0000 000F <zero:1> <zero:4> <crm:4> <opc1:4> <zero:3>
+
+ARM CCSIDR registers are demultiplexed by CSSELR value:
+  0x4020 0000 0011 00 <csselr:8>
+
+ARM 32-bit VFP control registers have the following id bit patterns:
+  0x4020 0000 0012 1 <regno:12>
+
+ARM 64-bit FP registers have the following id bit patterns:
+  0x4030 0000 0012 0 <regno:12>
+
+ARM firmware pseudo-registers have the following bit pattern:
+  0x4030 0000 0014 <regno:16>
+
+
+arm64 registers are mapped using the lower 32 bits. The upper 16 of
+that is the register group type, or coprocessor number:
+
+arm64 core/FP-SIMD registers have the following id bit patterns. Note
+that the size of the access is variable, as the kvm_regs structure
+contains elements ranging from 32 to 128 bits. The index is a 32bit
+value in the kvm_regs structure seen as a 32bit array.
+  0x60x0 0000 0010 <index into the kvm_regs struct:16>
+
+arm64 CCSIDR registers are demultiplexed by CSSELR value:
+  0x6020 0000 0011 00 <csselr:8>
+
+arm64 system registers have the following id bit patterns:
+  0x6030 0000 0013 <op0:2> <op1:3> <crn:4> <crm:4> <op2:3>
+
+arm64 firmware pseudo-registers have the following bit pattern:
+  0x6030 0000 0014 <regno:16>
+
+
+MIPS registers are mapped using the lower 32 bits.  The upper 16 of that is
+the register group type:
+
+MIPS core registers (see above) have the following id bit patterns:
+  0x7030 0000 0000 <reg:16>
+
+MIPS CP0 registers (see KVM_REG_MIPS_CP0_* above) have the following id bit
+patterns depending on whether they're 32-bit or 64-bit registers:
+  0x7020 0000 0001 00 <reg:5> <sel:3>   (32-bit)
+  0x7030 0000 0001 00 <reg:5> <sel:3>   (64-bit)
+
+Note: KVM_REG_MIPS_CP0_ENTRYLO0 and KVM_REG_MIPS_CP0_ENTRYLO1 are the MIPS64
+versions of the EntryLo registers regardless of the word size of the host
+hardware, host kernel, guest, and whether XPA is present in the guest, i.e.
+with the RI and XI bits (if they exist) in bits 63 and 62 respectively, and
+the PFNX field starting at bit 30.
+
+MIPS MAARs (see KVM_REG_MIPS_CP0_MAAR(*) above) have the following id bit
+patterns:
+  0x7030 0000 0001 01 <reg:8>
+
+MIPS KVM control registers (see above) have the following id bit patterns:
+  0x7030 0000 0002 <reg:16>
+
+MIPS FPU registers (see KVM_REG_MIPS_FPR_{32,64}() above) have the following
+id bit patterns depending on the size of the register being accessed. They are
+always accessed according to the current guest FPU mode (Status.FR and
+Config5.FRE), i.e. as the guest would see them, and they become unpredictable
+if the guest FPU mode is changed. MIPS SIMD Architecture (MSA) vector
+registers (see KVM_REG_MIPS_VEC_128() above) have similar patterns as they
+overlap the FPU registers:
+  0x7020 0000 0003 00 <0:3> <reg:5> (32-bit FPU registers)
+  0x7030 0000 0003 00 <0:3> <reg:5> (64-bit FPU registers)
+  0x7040 0000 0003 00 <0:3> <reg:5> (128-bit MSA vector registers)
+
+MIPS FPU control registers (see KVM_REG_MIPS_FCR_{IR,CSR} above) have the
+following id bit patterns:
+  0x7020 0000 0003 01 <0:3> <reg:5>
+
+MIPS MSA control registers (see KVM_REG_MIPS_MSA_{IR,CSR} above) have the
+following id bit patterns:
+  0x7020 0000 0003 02 <0:3> <reg:5>
+
+
+4.69 KVM_GET_ONE_REG
+
+Capability: KVM_CAP_ONE_REG
+Architectures: all
+Type: vcpu ioctl
+Parameters: struct kvm_one_reg (in and out)
+Returns: 0 on success, negative value on failure
+
+This ioctl allows to receive the value of a single register implemented
+in a vcpu. The register to read is indicated by the "id" field of the
+kvm_one_reg struct passed in. On success, the register value can be found
+at the memory location pointed to by "addr".
+
+The list of registers accessible using this interface is identical to the
+list in 4.68.
+
+
+4.70 KVM_KVMCLOCK_CTRL
+
+Capability: KVM_CAP_KVMCLOCK_CTRL
+Architectures: Any that implement pvclocks (currently x86 only)
+Type: vcpu ioctl
+Parameters: None
+Returns: 0 on success, -1 on error
+
+This signals to the host kernel that the specified guest is being paused by
+userspace.  The host will set a flag in the pvclock structure that is checked
+from the soft lockup watchdog.  The flag is part of the pvclock structure that
+is shared between guest and host, specifically the second bit of the flags
+field of the pvclock_vcpu_time_info structure.  It will be set exclusively by
+the host and read/cleared exclusively by the guest.  The guest operation of
+checking and clearing the flag must an atomic operation so
+load-link/store-conditional, or equivalent must be used.  There are two cases
+where the guest will clear the flag: when the soft lockup watchdog timer resets
+itself or when a soft lockup is detected.  This ioctl can be called any time
+after pausing the vcpu, but before it is resumed.
+
+
+4.71 KVM_SIGNAL_MSI
+
+Capability: KVM_CAP_SIGNAL_MSI
+Architectures: x86 arm arm64
+Type: vm ioctl
+Parameters: struct kvm_msi (in)
+Returns: >0 on delivery, 0 if guest blocked the MSI, and -1 on error
+
+Directly inject a MSI message. Only valid with in-kernel irqchip that handles
+MSI messages.
+
+struct kvm_msi {
+	__u32 address_lo;
+	__u32 address_hi;
+	__u32 data;
+	__u32 flags;
+	__u32 devid;
+	__u8  pad[12];
+};
+
+flags: KVM_MSI_VALID_DEVID: devid contains a valid value.  The per-VM
+  KVM_CAP_MSI_DEVID capability advertises the requirement to provide
+  the device ID.  If this capability is not available, userspace
+  should never set the KVM_MSI_VALID_DEVID flag as the ioctl might fail.
+
+If KVM_MSI_VALID_DEVID is set, devid contains a unique device identifier
+for the device that wrote the MSI message.  For PCI, this is usually a
+BFD identifier in the lower 16 bits.
+
+On x86, address_hi is ignored unless the KVM_X2APIC_API_USE_32BIT_IDS
+feature of KVM_CAP_X2APIC_API capability is enabled.  If it is enabled,
+address_hi bits 31-8 provide bits 31-8 of the destination id.  Bits 7-0 of
+address_hi must be zero.
+
+
+4.71 KVM_CREATE_PIT2
+
+Capability: KVM_CAP_PIT2
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_pit_config (in)
+Returns: 0 on success, -1 on error
+
+Creates an in-kernel device model for the i8254 PIT. This call is only valid
+after enabling in-kernel irqchip support via KVM_CREATE_IRQCHIP. The following
+parameters have to be passed:
+
+struct kvm_pit_config {
+	__u32 flags;
+	__u32 pad[15];
+};
+
+Valid flags are:
+
+#define KVM_PIT_SPEAKER_DUMMY     1 /* emulate speaker port stub */
+
+PIT timer interrupts may use a per-VM kernel thread for injection. If it
+exists, this thread will have a name of the following pattern:
+
+kvm-pit/<owner-process-pid>
+
+When running a guest with elevated priorities, the scheduling parameters of
+this thread may have to be adjusted accordingly.
+
+This IOCTL replaces the obsolete KVM_CREATE_PIT.
+
+
+4.72 KVM_GET_PIT2
+
+Capability: KVM_CAP_PIT_STATE2
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_pit_state2 (out)
+Returns: 0 on success, -1 on error
+
+Retrieves the state of the in-kernel PIT model. Only valid after
+KVM_CREATE_PIT2. The state is returned in the following structure:
+
+struct kvm_pit_state2 {
+	struct kvm_pit_channel_state channels[3];
+	__u32 flags;
+	__u32 reserved[9];
+};
+
+Valid flags are:
+
+/* disable PIT in HPET legacy mode */
+#define KVM_PIT_FLAGS_HPET_LEGACY  0x00000001
+
+This IOCTL replaces the obsolete KVM_GET_PIT.
+
+
+4.73 KVM_SET_PIT2
+
+Capability: KVM_CAP_PIT_STATE2
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_pit_state2 (in)
+Returns: 0 on success, -1 on error
+
+Sets the state of the in-kernel PIT model. Only valid after KVM_CREATE_PIT2.
+See KVM_GET_PIT2 for details on struct kvm_pit_state2.
+
+This IOCTL replaces the obsolete KVM_SET_PIT.
+
+
+4.74 KVM_PPC_GET_SMMU_INFO
+
+Capability: KVM_CAP_PPC_GET_SMMU_INFO
+Architectures: powerpc
+Type: vm ioctl
+Parameters: None
+Returns: 0 on success, -1 on error
+
+This populates and returns a structure describing the features of
+the "Server" class MMU emulation supported by KVM.
+This can in turn be used by userspace to generate the appropriate
+device-tree properties for the guest operating system.
+
+The structure contains some global information, followed by an
+array of supported segment page sizes:
+
+      struct kvm_ppc_smmu_info {
+	     __u64 flags;
+	     __u32 slb_size;
+	     __u32 pad;
+	     struct kvm_ppc_one_seg_page_size sps[KVM_PPC_PAGE_SIZES_MAX_SZ];
+      };
+
+The supported flags are:
+
+    - KVM_PPC_PAGE_SIZES_REAL:
+        When that flag is set, guest page sizes must "fit" the backing
+        store page sizes. When not set, any page size in the list can
+        be used regardless of how they are backed by userspace.
+
+    - KVM_PPC_1T_SEGMENTS
+        The emulated MMU supports 1T segments in addition to the
+        standard 256M ones.
+
+The "slb_size" field indicates how many SLB entries are supported
+
+The "sps" array contains 8 entries indicating the supported base
+page sizes for a segment in increasing order. Each entry is defined
+as follow:
+
+   struct kvm_ppc_one_seg_page_size {
+	__u32 page_shift;	/* Base page shift of segment (or 0) */
+	__u32 slb_enc;		/* SLB encoding for BookS */
+	struct kvm_ppc_one_page_size enc[KVM_PPC_PAGE_SIZES_MAX_SZ];
+   };
+
+An entry with a "page_shift" of 0 is unused. Because the array is
+organized in increasing order, a lookup can stop when encoutering
+such an entry.
+
+The "slb_enc" field provides the encoding to use in the SLB for the
+page size. The bits are in positions such as the value can directly
+be OR'ed into the "vsid" argument of the slbmte instruction.
+
+The "enc" array is a list which for each of those segment base page
+size provides the list of supported actual page sizes (which can be
+only larger or equal to the base page size), along with the
+corresponding encoding in the hash PTE. Similarly, the array is
+8 entries sorted by increasing sizes and an entry with a "0" shift
+is an empty entry and a terminator:
+
+   struct kvm_ppc_one_page_size {
+	__u32 page_shift;	/* Page shift (or 0) */
+	__u32 pte_enc;		/* Encoding in the HPTE (>>12) */
+   };
+
+The "pte_enc" field provides a value that can OR'ed into the hash
+PTE's RPN field (ie, it needs to be shifted left by 12 to OR it
+into the hash PTE second double word).
+
+4.75 KVM_IRQFD
+
+Capability: KVM_CAP_IRQFD
+Architectures: x86 s390 arm arm64
+Type: vm ioctl
+Parameters: struct kvm_irqfd (in)
+Returns: 0 on success, -1 on error
+
+Allows setting an eventfd to directly trigger a guest interrupt.
+kvm_irqfd.fd specifies the file descriptor to use as the eventfd and
+kvm_irqfd.gsi specifies the irqchip pin toggled by this event.  When
+an event is triggered on the eventfd, an interrupt is injected into
+the guest using the specified gsi pin.  The irqfd is removed using
+the KVM_IRQFD_FLAG_DEASSIGN flag, specifying both kvm_irqfd.fd
+and kvm_irqfd.gsi.
+
+With KVM_CAP_IRQFD_RESAMPLE, KVM_IRQFD supports a de-assert and notify
+mechanism allowing emulation of level-triggered, irqfd-based
+interrupts.  When KVM_IRQFD_FLAG_RESAMPLE is set the user must pass an
+additional eventfd in the kvm_irqfd.resamplefd field.  When operating
+in resample mode, posting of an interrupt through kvm_irq.fd asserts
+the specified gsi in the irqchip.  When the irqchip is resampled, such
+as from an EOI, the gsi is de-asserted and the user is notified via
+kvm_irqfd.resamplefd.  It is the user's responsibility to re-queue
+the interrupt if the device making use of it still requires service.
+Note that closing the resamplefd is not sufficient to disable the
+irqfd.  The KVM_IRQFD_FLAG_RESAMPLE is only necessary on assignment
+and need not be specified with KVM_IRQFD_FLAG_DEASSIGN.
+
+On arm/arm64, gsi routing being supported, the following can happen:
+- in case no routing entry is associated to this gsi, injection fails
+- in case the gsi is associated to an irqchip routing entry,
+  irqchip.pin + 32 corresponds to the injected SPI ID.
+- in case the gsi is associated to an MSI routing entry, the MSI
+  message and device ID are translated into an LPI (support restricted
+  to GICv3 ITS in-kernel emulation).
+
+4.76 KVM_PPC_ALLOCATE_HTAB
+
+Capability: KVM_CAP_PPC_ALLOC_HTAB
+Architectures: powerpc
+Type: vm ioctl
+Parameters: Pointer to u32 containing hash table order (in/out)
+Returns: 0 on success, -1 on error
+
+This requests the host kernel to allocate an MMU hash table for a
+guest using the PAPR paravirtualization interface.  This only does
+anything if the kernel is configured to use the Book 3S HV style of
+virtualization.  Otherwise the capability doesn't exist and the ioctl
+returns an ENOTTY error.  The rest of this description assumes Book 3S
+HV.
+
+There must be no vcpus running when this ioctl is called; if there
+are, it will do nothing and return an EBUSY error.
+
+The parameter is a pointer to a 32-bit unsigned integer variable
+containing the order (log base 2) of the desired size of the hash
+table, which must be between 18 and 46.  On successful return from the
+ioctl, the value will not be changed by the kernel.
+
+If no hash table has been allocated when any vcpu is asked to run
+(with the KVM_RUN ioctl), the host kernel will allocate a
+default-sized hash table (16 MB).
+
+If this ioctl is called when a hash table has already been allocated,
+with a different order from the existing hash table, the existing hash
+table will be freed and a new one allocated.  If this is ioctl is
+called when a hash table has already been allocated of the same order
+as specified, the kernel will clear out the existing hash table (zero
+all HPTEs).  In either case, if the guest is using the virtualized
+real-mode area (VRMA) facility, the kernel will re-create the VMRA
+HPTEs on the next KVM_RUN of any vcpu.
+
+4.77 KVM_S390_INTERRUPT
+
+Capability: basic
+Architectures: s390
+Type: vm ioctl, vcpu ioctl
+Parameters: struct kvm_s390_interrupt (in)
+Returns: 0 on success, -1 on error
+
+Allows to inject an interrupt to the guest. Interrupts can be floating
+(vm ioctl) or per cpu (vcpu ioctl), depending on the interrupt type.
+
+Interrupt parameters are passed via kvm_s390_interrupt:
+
+struct kvm_s390_interrupt {
+	__u32 type;
+	__u32 parm;
+	__u64 parm64;
+};
+
+type can be one of the following:
+
+KVM_S390_SIGP_STOP (vcpu) - sigp stop; optional flags in parm
+KVM_S390_PROGRAM_INT (vcpu) - program check; code in parm
+KVM_S390_SIGP_SET_PREFIX (vcpu) - sigp set prefix; prefix address in parm
+KVM_S390_RESTART (vcpu) - restart
+KVM_S390_INT_CLOCK_COMP (vcpu) - clock comparator interrupt
+KVM_S390_INT_CPU_TIMER (vcpu) - CPU timer interrupt
+KVM_S390_INT_VIRTIO (vm) - virtio external interrupt; external interrupt
+			   parameters in parm and parm64
+KVM_S390_INT_SERVICE (vm) - sclp external interrupt; sclp parameter in parm
+KVM_S390_INT_EMERGENCY (vcpu) - sigp emergency; source cpu in parm
+KVM_S390_INT_EXTERNAL_CALL (vcpu) - sigp external call; source cpu in parm
+KVM_S390_INT_IO(ai,cssid,ssid,schid) (vm) - compound value to indicate an
+    I/O interrupt (ai - adapter interrupt; cssid,ssid,schid - subchannel);
+    I/O interruption parameters in parm (subchannel) and parm64 (intparm,
+    interruption subclass)
+KVM_S390_MCHK (vm, vcpu) - machine check interrupt; cr 14 bits in parm,
+                           machine check interrupt code in parm64 (note that
+                           machine checks needing further payload are not
+                           supported by this ioctl)
+
+Note that the vcpu ioctl is asynchronous to vcpu execution.
+
+4.78 KVM_PPC_GET_HTAB_FD
+
+Capability: KVM_CAP_PPC_HTAB_FD
+Architectures: powerpc
+Type: vm ioctl
+Parameters: Pointer to struct kvm_get_htab_fd (in)
+Returns: file descriptor number (>= 0) on success, -1 on error
+
+This returns a file descriptor that can be used either to read out the
+entries in the guest's hashed page table (HPT), or to write entries to
+initialize the HPT.  The returned fd can only be written to if the
+KVM_GET_HTAB_WRITE bit is set in the flags field of the argument, and
+can only be read if that bit is clear.  The argument struct looks like
+this:
+
+/* For KVM_PPC_GET_HTAB_FD */
+struct kvm_get_htab_fd {
+	__u64	flags;
+	__u64	start_index;
+	__u64	reserved[2];
+};
+
+/* Values for kvm_get_htab_fd.flags */
+#define KVM_GET_HTAB_BOLTED_ONLY	((__u64)0x1)
+#define KVM_GET_HTAB_WRITE		((__u64)0x2)
+
+The `start_index' field gives the index in the HPT of the entry at
+which to start reading.  It is ignored when writing.
+
+Reads on the fd will initially supply information about all
+"interesting" HPT entries.  Interesting entries are those with the
+bolted bit set, if the KVM_GET_HTAB_BOLTED_ONLY bit is set, otherwise
+all entries.  When the end of the HPT is reached, the read() will
+return.  If read() is called again on the fd, it will start again from
+the beginning of the HPT, but will only return HPT entries that have
+changed since they were last read.
+
+Data read or written is structured as a header (8 bytes) followed by a
+series of valid HPT entries (16 bytes) each.  The header indicates how
+many valid HPT entries there are and how many invalid entries follow
+the valid entries.  The invalid entries are not represented explicitly
+in the stream.  The header format is:
+
+struct kvm_get_htab_header {
+	__u32	index;
+	__u16	n_valid;
+	__u16	n_invalid;
+};
+
+Writes to the fd create HPT entries starting at the index given in the
+header; first `n_valid' valid entries with contents from the data
+written, then `n_invalid' invalid entries, invalidating any previously
+valid entries found.
+
+4.79 KVM_CREATE_DEVICE
+
+Capability: KVM_CAP_DEVICE_CTRL
+Type: vm ioctl
+Parameters: struct kvm_create_device (in/out)
+Returns: 0 on success, -1 on error
+Errors:
+  ENODEV: The device type is unknown or unsupported
+  EEXIST: Device already created, and this type of device may not
+          be instantiated multiple times
+
+  Other error conditions may be defined by individual device types or
+  have their standard meanings.
+
+Creates an emulated device in the kernel.  The file descriptor returned
+in fd can be used with KVM_SET/GET/HAS_DEVICE_ATTR.
+
+If the KVM_CREATE_DEVICE_TEST flag is set, only test whether the
+device type is supported (not necessarily whether it can be created
+in the current vm).
+
+Individual devices should not define flags.  Attributes should be used
+for specifying any behavior that is not implied by the device type
+number.
+
+struct kvm_create_device {
+	__u32	type;	/* in: KVM_DEV_TYPE_xxx */
+	__u32	fd;	/* out: device handle */
+	__u32	flags;	/* in: KVM_CREATE_DEVICE_xxx */
+};
+
+4.80 KVM_SET_DEVICE_ATTR/KVM_GET_DEVICE_ATTR
+
+Capability: KVM_CAP_DEVICE_CTRL, KVM_CAP_VM_ATTRIBUTES for vm device,
+  KVM_CAP_VCPU_ATTRIBUTES for vcpu device
+Type: device ioctl, vm ioctl, vcpu ioctl
+Parameters: struct kvm_device_attr
+Returns: 0 on success, -1 on error
+Errors:
+  ENXIO:  The group or attribute is unknown/unsupported for this device
+          or hardware support is missing.
+  EPERM:  The attribute cannot (currently) be accessed this way
+          (e.g. read-only attribute, or attribute that only makes
+          sense when the device is in a different state)
+
+  Other error conditions may be defined by individual device types.
+
+Gets/sets a specified piece of device configuration and/or state.  The
+semantics are device-specific.  See individual device documentation in
+the "devices" directory.  As with ONE_REG, the size of the data
+transferred is defined by the particular attribute.
+
+struct kvm_device_attr {
+	__u32	flags;		/* no flags currently defined */
+	__u32	group;		/* device-defined */
+	__u64	attr;		/* group-defined */
+	__u64	addr;		/* userspace address of attr data */
+};
+
+4.81 KVM_HAS_DEVICE_ATTR
+
+Capability: KVM_CAP_DEVICE_CTRL, KVM_CAP_VM_ATTRIBUTES for vm device,
+  KVM_CAP_VCPU_ATTRIBUTES for vcpu device
+Type: device ioctl, vm ioctl, vcpu ioctl
+Parameters: struct kvm_device_attr
+Returns: 0 on success, -1 on error
+Errors:
+  ENXIO:  The group or attribute is unknown/unsupported for this device
+          or hardware support is missing.
+
+Tests whether a device supports a particular attribute.  A successful
+return indicates the attribute is implemented.  It does not necessarily
+indicate that the attribute can be read or written in the device's
+current state.  "addr" is ignored.
+
+4.82 KVM_ARM_VCPU_INIT
+
+Capability: basic
+Architectures: arm, arm64
+Type: vcpu ioctl
+Parameters: struct kvm_vcpu_init (in)
+Returns: 0 on success; -1 on error
+Errors:
+  EINVAL:    the target is unknown, or the combination of features is invalid.
+  ENOENT:    a features bit specified is unknown.
+
+This tells KVM what type of CPU to present to the guest, and what
+optional features it should have.  This will cause a reset of the cpu
+registers to their initial values.  If this is not called, KVM_RUN will
+return ENOEXEC for that vcpu.
+
+Note that because some registers reflect machine topology, all vcpus
+should be created before this ioctl is invoked.
+
+Userspace can call this function multiple times for a given vcpu, including
+after the vcpu has been run. This will reset the vcpu to its initial
+state. All calls to this function after the initial call must use the same
+target and same set of feature flags, otherwise EINVAL will be returned.
+
+Possible features:
+	- KVM_ARM_VCPU_POWER_OFF: Starts the CPU in a power-off state.
+	  Depends on KVM_CAP_ARM_PSCI.  If not set, the CPU will be powered on
+	  and execute guest code when KVM_RUN is called.
+	- KVM_ARM_VCPU_EL1_32BIT: Starts the CPU in a 32bit mode.
+	  Depends on KVM_CAP_ARM_EL1_32BIT (arm64 only).
+	- KVM_ARM_VCPU_PSCI_0_2: Emulate PSCI v0.2 (or a future revision
+          backward compatible with v0.2) for the CPU.
+	  Depends on KVM_CAP_ARM_PSCI_0_2.
+	- KVM_ARM_VCPU_PMU_V3: Emulate PMUv3 for the CPU.
+	  Depends on KVM_CAP_ARM_PMU_V3.
+
+
+4.83 KVM_ARM_PREFERRED_TARGET
+
+Capability: basic
+Architectures: arm, arm64
+Type: vm ioctl
+Parameters: struct struct kvm_vcpu_init (out)
+Returns: 0 on success; -1 on error
+Errors:
+  ENODEV:    no preferred target available for the host
+
+This queries KVM for preferred CPU target type which can be emulated
+by KVM on underlying host.
+
+The ioctl returns struct kvm_vcpu_init instance containing information
+about preferred CPU target type and recommended features for it.  The
+kvm_vcpu_init->features bitmap returned will have feature bits set if
+the preferred target recommends setting these features, but this is
+not mandatory.
+
+The information returned by this ioctl can be used to prepare an instance
+of struct kvm_vcpu_init for KVM_ARM_VCPU_INIT ioctl which will result in
+in VCPU matching underlying host.
+
+
+4.84 KVM_GET_REG_LIST
+
+Capability: basic
+Architectures: arm, arm64, mips
+Type: vcpu ioctl
+Parameters: struct kvm_reg_list (in/out)
+Returns: 0 on success; -1 on error
+Errors:
+  E2BIG:     the reg index list is too big to fit in the array specified by
+             the user (the number required will be written into n).
+
+struct kvm_reg_list {
+	__u64 n; /* number of registers in reg[] */
+	__u64 reg[0];
+};
+
+This ioctl returns the guest registers that are supported for the
+KVM_GET_ONE_REG/KVM_SET_ONE_REG calls.
+
+
+4.85 KVM_ARM_SET_DEVICE_ADDR (deprecated)
+
+Capability: KVM_CAP_ARM_SET_DEVICE_ADDR
+Architectures: arm, arm64
+Type: vm ioctl
+Parameters: struct kvm_arm_device_address (in)
+Returns: 0 on success, -1 on error
+Errors:
+  ENODEV: The device id is unknown
+  ENXIO:  Device not supported on current system
+  EEXIST: Address already set
+  E2BIG:  Address outside guest physical address space
+  EBUSY:  Address overlaps with other device range
+
+struct kvm_arm_device_addr {
+	__u64 id;
+	__u64 addr;
+};
+
+Specify a device address in the guest's physical address space where guests
+can access emulated or directly exposed devices, which the host kernel needs
+to know about. The id field is an architecture specific identifier for a
+specific device.
+
+ARM/arm64 divides the id field into two parts, a device id and an
+address type id specific to the individual device.
+
+  bits:  | 63        ...       32 | 31    ...    16 | 15    ...    0 |
+  field: |        0x00000000      |     device id   |  addr type id  |
+
+ARM/arm64 currently only require this when using the in-kernel GIC
+support for the hardware VGIC features, using KVM_ARM_DEVICE_VGIC_V2
+as the device id.  When setting the base address for the guest's
+mapping of the VGIC virtual CPU and distributor interface, the ioctl
+must be called after calling KVM_CREATE_IRQCHIP, but before calling
+KVM_RUN on any of the VCPUs.  Calling this ioctl twice for any of the
+base addresses will return -EEXIST.
+
+Note, this IOCTL is deprecated and the more flexible SET/GET_DEVICE_ATTR API
+should be used instead.
+
+
+4.86 KVM_PPC_RTAS_DEFINE_TOKEN
+
+Capability: KVM_CAP_PPC_RTAS
+Architectures: ppc
+Type: vm ioctl
+Parameters: struct kvm_rtas_token_args
+Returns: 0 on success, -1 on error
+
+Defines a token value for a RTAS (Run Time Abstraction Services)
+service in order to allow it to be handled in the kernel.  The
+argument struct gives the name of the service, which must be the name
+of a service that has a kernel-side implementation.  If the token
+value is non-zero, it will be associated with that service, and
+subsequent RTAS calls by the guest specifying that token will be
+handled by the kernel.  If the token value is 0, then any token
+associated with the service will be forgotten, and subsequent RTAS
+calls by the guest for that service will be passed to userspace to be
+handled.
+
+4.87 KVM_SET_GUEST_DEBUG
+
+Capability: KVM_CAP_SET_GUEST_DEBUG
+Architectures: x86, s390, ppc, arm64
+Type: vcpu ioctl
+Parameters: struct kvm_guest_debug (in)
+Returns: 0 on success; -1 on error
+
+struct kvm_guest_debug {
+       __u32 control;
+       __u32 pad;
+       struct kvm_guest_debug_arch arch;
+};
+
+Set up the processor specific debug registers and configure vcpu for
+handling guest debug events. There are two parts to the structure, the
+first a control bitfield indicates the type of debug events to handle
+when running. Common control bits are:
+
+  - KVM_GUESTDBG_ENABLE:        guest debugging is enabled
+  - KVM_GUESTDBG_SINGLESTEP:    the next run should single-step
+
+The top 16 bits of the control field are architecture specific control
+flags which can include the following:
+
+  - KVM_GUESTDBG_USE_SW_BP:     using software breakpoints [x86, arm64]
+  - KVM_GUESTDBG_USE_HW_BP:     using hardware breakpoints [x86, s390, arm64]
+  - KVM_GUESTDBG_INJECT_DB:     inject DB type exception [x86]
+  - KVM_GUESTDBG_INJECT_BP:     inject BP type exception [x86]
+  - KVM_GUESTDBG_EXIT_PENDING:  trigger an immediate guest exit [s390]
+
+For example KVM_GUESTDBG_USE_SW_BP indicates that software breakpoints
+are enabled in memory so we need to ensure breakpoint exceptions are
+correctly trapped and the KVM run loop exits at the breakpoint and not
+running off into the normal guest vector. For KVM_GUESTDBG_USE_HW_BP
+we need to ensure the guest vCPUs architecture specific registers are
+updated to the correct (supplied) values.
+
+The second part of the structure is architecture specific and
+typically contains a set of debug registers.
+
+For arm64 the number of debug registers is implementation defined and
+can be determined by querying the KVM_CAP_GUEST_DEBUG_HW_BPS and
+KVM_CAP_GUEST_DEBUG_HW_WPS capabilities which return a positive number
+indicating the number of supported registers.
+
+When debug events exit the main run loop with the reason
+KVM_EXIT_DEBUG with the kvm_debug_exit_arch part of the kvm_run
+structure containing architecture specific debug information.
+
+4.88 KVM_GET_EMULATED_CPUID
+
+Capability: KVM_CAP_EXT_EMUL_CPUID
+Architectures: x86
+Type: system ioctl
+Parameters: struct kvm_cpuid2 (in/out)
+Returns: 0 on success, -1 on error
+
+struct kvm_cpuid2 {
+	__u32 nent;
+	__u32 flags;
+	struct kvm_cpuid_entry2 entries[0];
+};
+
+The member 'flags' is used for passing flags from userspace.
+
+#define KVM_CPUID_FLAG_SIGNIFCANT_INDEX		BIT(0)
+#define KVM_CPUID_FLAG_STATEFUL_FUNC		BIT(1)
+#define KVM_CPUID_FLAG_STATE_READ_NEXT		BIT(2)
+
+struct kvm_cpuid_entry2 {
+	__u32 function;
+	__u32 index;
+	__u32 flags;
+	__u32 eax;
+	__u32 ebx;
+	__u32 ecx;
+	__u32 edx;
+	__u32 padding[3];
+};
+
+This ioctl returns x86 cpuid features which are emulated by
+kvm.Userspace can use the information returned by this ioctl to query
+which features are emulated by kvm instead of being present natively.
+
+Userspace invokes KVM_GET_EMULATED_CPUID by passing a kvm_cpuid2
+structure with the 'nent' field indicating the number of entries in
+the variable-size array 'entries'. If the number of entries is too low
+to describe the cpu capabilities, an error (E2BIG) is returned. If the
+number is too high, the 'nent' field is adjusted and an error (ENOMEM)
+is returned. If the number is just right, the 'nent' field is adjusted
+to the number of valid entries in the 'entries' array, which is then
+filled.
+
+The entries returned are the set CPUID bits of the respective features
+which kvm emulates, as returned by the CPUID instruction, with unknown
+or unsupported feature bits cleared.
+
+Features like x2apic, for example, may not be present in the host cpu
+but are exposed by kvm in KVM_GET_SUPPORTED_CPUID because they can be
+emulated efficiently and thus not included here.
+
+The fields in each entry are defined as follows:
+
+  function: the eax value used to obtain the entry
+  index: the ecx value used to obtain the entry (for entries that are
+         affected by ecx)
+  flags: an OR of zero or more of the following:
+        KVM_CPUID_FLAG_SIGNIFCANT_INDEX:
+           if the index field is valid
+        KVM_CPUID_FLAG_STATEFUL_FUNC:
+           if cpuid for this function returns different values for successive
+           invocations; there will be several entries with the same function,
+           all with this flag set
+        KVM_CPUID_FLAG_STATE_READ_NEXT:
+           for KVM_CPUID_FLAG_STATEFUL_FUNC entries, set if this entry is
+           the first entry to be read by a cpu
+   eax, ebx, ecx, edx: the values returned by the cpuid instruction for
+         this function/index combination
+
+4.89 KVM_S390_MEM_OP
+
+Capability: KVM_CAP_S390_MEM_OP
+Architectures: s390
+Type: vcpu ioctl
+Parameters: struct kvm_s390_mem_op (in)
+Returns: = 0 on success,
+         < 0 on generic error (e.g. -EFAULT or -ENOMEM),
+         > 0 if an exception occurred while walking the page tables
+
+Read or write data from/to the logical (virtual) memory of a VCPU.
+
+Parameters are specified via the following structure:
+
+struct kvm_s390_mem_op {
+	__u64 gaddr;		/* the guest address */
+	__u64 flags;		/* flags */
+	__u32 size;		/* amount of bytes */
+	__u32 op;		/* type of operation */
+	__u64 buf;		/* buffer in userspace */
+	__u8 ar;		/* the access register number */
+	__u8 reserved[31];	/* should be set to 0 */
+};
+
+The type of operation is specified in the "op" field. It is either
+KVM_S390_MEMOP_LOGICAL_READ for reading from logical memory space or
+KVM_S390_MEMOP_LOGICAL_WRITE for writing to logical memory space. The
+KVM_S390_MEMOP_F_CHECK_ONLY flag can be set in the "flags" field to check
+whether the corresponding memory access would create an access exception
+(without touching the data in the memory at the destination). In case an
+access exception occurred while walking the MMU tables of the guest, the
+ioctl returns a positive error number to indicate the type of exception.
+This exception is also raised directly at the corresponding VCPU if the
+flag KVM_S390_MEMOP_F_INJECT_EXCEPTION is set in the "flags" field.
+
+The start address of the memory region has to be specified in the "gaddr"
+field, and the length of the region in the "size" field. "buf" is the buffer
+supplied by the userspace application where the read data should be written
+to for KVM_S390_MEMOP_LOGICAL_READ, or where the data that should be written
+is stored for a KVM_S390_MEMOP_LOGICAL_WRITE. "buf" is unused and can be NULL
+when KVM_S390_MEMOP_F_CHECK_ONLY is specified. "ar" designates the access
+register number to be used.
+
+The "reserved" field is meant for future extensions. It is not used by
+KVM with the currently defined set of flags.
+
+4.90 KVM_S390_GET_SKEYS
+
+Capability: KVM_CAP_S390_SKEYS
+Architectures: s390
+Type: vm ioctl
+Parameters: struct kvm_s390_skeys
+Returns: 0 on success, KVM_S390_GET_KEYS_NONE if guest is not using storage
+         keys, negative value on error
+
+This ioctl is used to get guest storage key values on the s390
+architecture. The ioctl takes parameters via the kvm_s390_skeys struct.
+
+struct kvm_s390_skeys {
+	__u64 start_gfn;
+	__u64 count;
+	__u64 skeydata_addr;
+	__u32 flags;
+	__u32 reserved[9];
+};
+
+The start_gfn field is the number of the first guest frame whose storage keys
+you want to get.
+
+The count field is the number of consecutive frames (starting from start_gfn)
+whose storage keys to get. The count field must be at least 1 and the maximum
+allowed value is defined as KVM_S390_SKEYS_ALLOC_MAX. Values outside this range
+will cause the ioctl to return -EINVAL.
+
+The skeydata_addr field is the address to a buffer large enough to hold count
+bytes. This buffer will be filled with storage key data by the ioctl.
+
+4.91 KVM_S390_SET_SKEYS
+
+Capability: KVM_CAP_S390_SKEYS
+Architectures: s390
+Type: vm ioctl
+Parameters: struct kvm_s390_skeys
+Returns: 0 on success, negative value on error
+
+This ioctl is used to set guest storage key values on the s390
+architecture. The ioctl takes parameters via the kvm_s390_skeys struct.
+See section on KVM_S390_GET_SKEYS for struct definition.
+
+The start_gfn field is the number of the first guest frame whose storage keys
+you want to set.
+
+The count field is the number of consecutive frames (starting from start_gfn)
+whose storage keys to get. The count field must be at least 1 and the maximum
+allowed value is defined as KVM_S390_SKEYS_ALLOC_MAX. Values outside this range
+will cause the ioctl to return -EINVAL.
+
+The skeydata_addr field is the address to a buffer containing count bytes of
+storage keys. Each byte in the buffer will be set as the storage key for a
+single frame starting at start_gfn for count frames.
+
+Note: If any architecturally invalid key value is found in the given data then
+the ioctl will return -EINVAL.
+
+4.92 KVM_S390_IRQ
+
+Capability: KVM_CAP_S390_INJECT_IRQ
+Architectures: s390
+Type: vcpu ioctl
+Parameters: struct kvm_s390_irq (in)
+Returns: 0 on success, -1 on error
+Errors:
+  EINVAL: interrupt type is invalid
+          type is KVM_S390_SIGP_STOP and flag parameter is invalid value
+          type is KVM_S390_INT_EXTERNAL_CALL and code is bigger
+            than the maximum of VCPUs
+  EBUSY:  type is KVM_S390_SIGP_SET_PREFIX and vcpu is not stopped
+          type is KVM_S390_SIGP_STOP and a stop irq is already pending
+          type is KVM_S390_INT_EXTERNAL_CALL and an external call interrupt
+            is already pending
+
+Allows to inject an interrupt to the guest.
+
+Using struct kvm_s390_irq as a parameter allows
+to inject additional payload which is not
+possible via KVM_S390_INTERRUPT.
+
+Interrupt parameters are passed via kvm_s390_irq:
+
+struct kvm_s390_irq {
+	__u64 type;
+	union {
+		struct kvm_s390_io_info io;
+		struct kvm_s390_ext_info ext;
+		struct kvm_s390_pgm_info pgm;
+		struct kvm_s390_emerg_info emerg;
+		struct kvm_s390_extcall_info extcall;
+		struct kvm_s390_prefix_info prefix;
+		struct kvm_s390_stop_info stop;
+		struct kvm_s390_mchk_info mchk;
+		char reserved[64];
+	} u;
+};
+
+type can be one of the following:
+
+KVM_S390_SIGP_STOP - sigp stop; parameter in .stop
+KVM_S390_PROGRAM_INT - program check; parameters in .pgm
+KVM_S390_SIGP_SET_PREFIX - sigp set prefix; parameters in .prefix
+KVM_S390_RESTART - restart; no parameters
+KVM_S390_INT_CLOCK_COMP - clock comparator interrupt; no parameters
+KVM_S390_INT_CPU_TIMER - CPU timer interrupt; no parameters
+KVM_S390_INT_EMERGENCY - sigp emergency; parameters in .emerg
+KVM_S390_INT_EXTERNAL_CALL - sigp external call; parameters in .extcall
+KVM_S390_MCHK - machine check interrupt; parameters in .mchk
+
+
+Note that the vcpu ioctl is asynchronous to vcpu execution.
+
+4.94 KVM_S390_GET_IRQ_STATE
+
+Capability: KVM_CAP_S390_IRQ_STATE
+Architectures: s390
+Type: vcpu ioctl
+Parameters: struct kvm_s390_irq_state (out)
+Returns: >= number of bytes copied into buffer,
+         -EINVAL if buffer size is 0,
+         -ENOBUFS if buffer size is too small to fit all pending interrupts,
+         -EFAULT if the buffer address was invalid
+
+This ioctl allows userspace to retrieve the complete state of all currently
+pending interrupts in a single buffer. Use cases include migration
+and introspection. The parameter structure contains the address of a
+userspace buffer and its length:
+
+struct kvm_s390_irq_state {
+	__u64 buf;
+	__u32 flags;        /* will stay unused for compatibility reasons */
+	__u32 len;
+	__u32 reserved[4];  /* will stay unused for compatibility reasons */
+};
+
+Userspace passes in the above struct and for each pending interrupt a
+struct kvm_s390_irq is copied to the provided buffer.
+
+The structure contains a flags and a reserved field for future extensions. As
+the kernel never checked for flags == 0 and QEMU never pre-zeroed flags and
+reserved, these fields can not be used in the future without breaking
+compatibility.
+
+If -ENOBUFS is returned the buffer provided was too small and userspace
+may retry with a bigger buffer.
+
+4.95 KVM_S390_SET_IRQ_STATE
+
+Capability: KVM_CAP_S390_IRQ_STATE
+Architectures: s390
+Type: vcpu ioctl
+Parameters: struct kvm_s390_irq_state (in)
+Returns: 0 on success,
+         -EFAULT if the buffer address was invalid,
+         -EINVAL for an invalid buffer length (see below),
+         -EBUSY if there were already interrupts pending,
+         errors occurring when actually injecting the
+          interrupt. See KVM_S390_IRQ.
+
+This ioctl allows userspace to set the complete state of all cpu-local
+interrupts currently pending for the vcpu. It is intended for restoring
+interrupt state after a migration. The input parameter is a userspace buffer
+containing a struct kvm_s390_irq_state:
+
+struct kvm_s390_irq_state {
+	__u64 buf;
+	__u32 flags;        /* will stay unused for compatibility reasons */
+	__u32 len;
+	__u32 reserved[4];  /* will stay unused for compatibility reasons */
+};
+
+The restrictions for flags and reserved apply as well.
+(see KVM_S390_GET_IRQ_STATE)
+
+The userspace memory referenced by buf contains a struct kvm_s390_irq
+for each interrupt to be injected into the guest.
+If one of the interrupts could not be injected for some reason the
+ioctl aborts.
+
+len must be a multiple of sizeof(struct kvm_s390_irq). It must be > 0
+and it must not exceed (max_vcpus + 32) * sizeof(struct kvm_s390_irq),
+which is the maximum number of possibly pending cpu-local interrupts.
+
+4.96 KVM_SMI
+
+Capability: KVM_CAP_X86_SMM
+Architectures: x86
+Type: vcpu ioctl
+Parameters: none
+Returns: 0 on success, -1 on error
+
+Queues an SMI on the thread's vcpu.
+
+4.97 KVM_CAP_PPC_MULTITCE
+
+Capability: KVM_CAP_PPC_MULTITCE
+Architectures: ppc
+Type: vm
+
+This capability means the kernel is capable of handling hypercalls
+H_PUT_TCE_INDIRECT and H_STUFF_TCE without passing those into the user
+space. This significantly accelerates DMA operations for PPC KVM guests.
+User space should expect that its handlers for these hypercalls
+are not going to be called if user space previously registered LIOBN
+in KVM (via KVM_CREATE_SPAPR_TCE or similar calls).
+
+In order to enable H_PUT_TCE_INDIRECT and H_STUFF_TCE use in the guest,
+user space might have to advertise it for the guest. For example,
+IBM pSeries (sPAPR) guest starts using them if "hcall-multi-tce" is
+present in the "ibm,hypertas-functions" device-tree property.
+
+The hypercalls mentioned above may or may not be processed successfully
+in the kernel based fast path. If they can not be handled by the kernel,
+they will get passed on to user space. So user space still has to have
+an implementation for these despite the in kernel acceleration.
+
+This capability is always enabled.
+
+4.98 KVM_CREATE_SPAPR_TCE_64
+
+Capability: KVM_CAP_SPAPR_TCE_64
+Architectures: powerpc
+Type: vm ioctl
+Parameters: struct kvm_create_spapr_tce_64 (in)
+Returns: file descriptor for manipulating the created TCE table
+
+This is an extension for KVM_CAP_SPAPR_TCE which only supports 32bit
+windows, described in 4.62 KVM_CREATE_SPAPR_TCE
+
+This capability uses extended struct in ioctl interface:
+
+/* for KVM_CAP_SPAPR_TCE_64 */
+struct kvm_create_spapr_tce_64 {
+	__u64 liobn;
+	__u32 page_shift;
+	__u32 flags;
+	__u64 offset;	/* in pages */
+	__u64 size; 	/* in pages */
+};
+
+The aim of extension is to support an additional bigger DMA window with
+a variable page size.
+KVM_CREATE_SPAPR_TCE_64 receives a 64bit window size, an IOMMU page shift and
+a bus offset of the corresponding DMA window, @size and @offset are numbers
+of IOMMU pages.
+
+@flags are not used at the moment.
+
+The rest of functionality is identical to KVM_CREATE_SPAPR_TCE.
+
+4.99 KVM_REINJECT_CONTROL
+
+Capability: KVM_CAP_REINJECT_CONTROL
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_reinject_control (in)
+Returns: 0 on success,
+         -EFAULT if struct kvm_reinject_control cannot be read,
+         -ENXIO if KVM_CREATE_PIT or KVM_CREATE_PIT2 didn't succeed earlier.
+
+i8254 (PIT) has two modes, reinject and !reinject.  The default is reinject,
+where KVM queues elapsed i8254 ticks and monitors completion of interrupt from
+vector(s) that i8254 injects.  Reinject mode dequeues a tick and injects its
+interrupt whenever there isn't a pending interrupt from i8254.
+!reinject mode injects an interrupt as soon as a tick arrives.
+
+struct kvm_reinject_control {
+	__u8 pit_reinject;
+	__u8 reserved[31];
+};
+
+pit_reinject = 0 (!reinject mode) is recommended, unless running an old
+operating system that uses the PIT for timing (e.g. Linux 2.4.x).
+
+4.100 KVM_PPC_CONFIGURE_V3_MMU
+
+Capability: KVM_CAP_PPC_RADIX_MMU or KVM_CAP_PPC_HASH_MMU_V3
+Architectures: ppc
+Type: vm ioctl
+Parameters: struct kvm_ppc_mmuv3_cfg (in)
+Returns: 0 on success,
+         -EFAULT if struct kvm_ppc_mmuv3_cfg cannot be read,
+         -EINVAL if the configuration is invalid
+
+This ioctl controls whether the guest will use radix or HPT (hashed
+page table) translation, and sets the pointer to the process table for
+the guest.
+
+struct kvm_ppc_mmuv3_cfg {
+	__u64	flags;
+	__u64	process_table;
+};
+
+There are two bits that can be set in flags; KVM_PPC_MMUV3_RADIX and
+KVM_PPC_MMUV3_GTSE.  KVM_PPC_MMUV3_RADIX, if set, configures the guest
+to use radix tree translation, and if clear, to use HPT translation.
+KVM_PPC_MMUV3_GTSE, if set and if KVM permits it, configures the guest
+to be able to use the global TLB and SLB invalidation instructions;
+if clear, the guest may not use these instructions.
+
+The process_table field specifies the address and size of the guest
+process table, which is in the guest's space.  This field is formatted
+as the second doubleword of the partition table entry, as defined in
+the Power ISA V3.00, Book III section 5.7.6.1.
+
+4.101 KVM_PPC_GET_RMMU_INFO
+
+Capability: KVM_CAP_PPC_RADIX_MMU
+Architectures: ppc
+Type: vm ioctl
+Parameters: struct kvm_ppc_rmmu_info (out)
+Returns: 0 on success,
+	 -EFAULT if struct kvm_ppc_rmmu_info cannot be written,
+	 -EINVAL if no useful information can be returned
+
+This ioctl returns a structure containing two things: (a) a list
+containing supported radix tree geometries, and (b) a list that maps
+page sizes to put in the "AP" (actual page size) field for the tlbie
+(TLB invalidate entry) instruction.
+
+struct kvm_ppc_rmmu_info {
+	struct kvm_ppc_radix_geom {
+		__u8	page_shift;
+		__u8	level_bits[4];
+		__u8	pad[3];
+	}	geometries[8];
+	__u32	ap_encodings[8];
+};
+
+The geometries[] field gives up to 8 supported geometries for the
+radix page table, in terms of the log base 2 of the smallest page
+size, and the number of bits indexed at each level of the tree, from
+the PTE level up to the PGD level in that order.  Any unused entries
+will have 0 in the page_shift field.
+
+The ap_encodings gives the supported page sizes and their AP field
+encodings, encoded with the AP value in the top 3 bits and the log
+base 2 of the page size in the bottom 6 bits.
+
+4.102 KVM_PPC_RESIZE_HPT_PREPARE
+
+Capability: KVM_CAP_SPAPR_RESIZE_HPT
+Architectures: powerpc
+Type: vm ioctl
+Parameters: struct kvm_ppc_resize_hpt (in)
+Returns: 0 on successful completion,
+	 >0 if a new HPT is being prepared, the value is an estimated
+             number of milliseconds until preparation is complete
+         -EFAULT if struct kvm_reinject_control cannot be read,
+	 -EINVAL if the supplied shift or flags are invalid
+	 -ENOMEM if unable to allocate the new HPT
+	 -ENOSPC if there was a hash collision when moving existing
+                  HPT entries to the new HPT
+	 -EIO on other error conditions
+
+Used to implement the PAPR extension for runtime resizing of a guest's
+Hashed Page Table (HPT).  Specifically this starts, stops or monitors
+the preparation of a new potential HPT for the guest, essentially
+implementing the H_RESIZE_HPT_PREPARE hypercall.
+
+If called with shift > 0 when there is no pending HPT for the guest,
+this begins preparation of a new pending HPT of size 2^(shift) bytes.
+It then returns a positive integer with the estimated number of
+milliseconds until preparation is complete.
+
+If called when there is a pending HPT whose size does not match that
+requested in the parameters, discards the existing pending HPT and
+creates a new one as above.
+
+If called when there is a pending HPT of the size requested, will:
+  * If preparation of the pending HPT is already complete, return 0
+  * If preparation of the pending HPT has failed, return an error
+    code, then discard the pending HPT.
+  * If preparation of the pending HPT is still in progress, return an
+    estimated number of milliseconds until preparation is complete.
+
+If called with shift == 0, discards any currently pending HPT and
+returns 0 (i.e. cancels any in-progress preparation).
+
+flags is reserved for future expansion, currently setting any bits in
+flags will result in an -EINVAL.
+
+Normally this will be called repeatedly with the same parameters until
+it returns <= 0.  The first call will initiate preparation, subsequent
+ones will monitor preparation until it completes or fails.
+
+struct kvm_ppc_resize_hpt {
+	__u64 flags;
+	__u32 shift;
+	__u32 pad;
+};
+
+4.103 KVM_PPC_RESIZE_HPT_COMMIT
+
+Capability: KVM_CAP_SPAPR_RESIZE_HPT
+Architectures: powerpc
+Type: vm ioctl
+Parameters: struct kvm_ppc_resize_hpt (in)
+Returns: 0 on successful completion,
+         -EFAULT if struct kvm_reinject_control cannot be read,
+	 -EINVAL if the supplied shift or flags are invalid
+	 -ENXIO is there is no pending HPT, or the pending HPT doesn't
+                 have the requested size
+	 -EBUSY if the pending HPT is not fully prepared
+	 -ENOSPC if there was a hash collision when moving existing
+                  HPT entries to the new HPT
+	 -EIO on other error conditions
+
+Used to implement the PAPR extension for runtime resizing of a guest's
+Hashed Page Table (HPT).  Specifically this requests that the guest be
+transferred to working with the new HPT, essentially implementing the
+H_RESIZE_HPT_COMMIT hypercall.
+
+This should only be called after KVM_PPC_RESIZE_HPT_PREPARE has
+returned 0 with the same parameters.  In other cases
+KVM_PPC_RESIZE_HPT_COMMIT will return an error (usually -ENXIO or
+-EBUSY, though others may be possible if the preparation was started,
+but failed).
+
+This will have undefined effects on the guest if it has not already
+placed itself in a quiescent state where no vcpu will make MMU enabled
+memory accesses.
+
+On succsful completion, the pending HPT will become the guest's active
+HPT and the previous HPT will be discarded.
+
+On failure, the guest will still be operating on its previous HPT.
+
+struct kvm_ppc_resize_hpt {
+	__u64 flags;
+	__u32 shift;
+	__u32 pad;
+};
+
+4.104 KVM_X86_GET_MCE_CAP_SUPPORTED
+
+Capability: KVM_CAP_MCE
+Architectures: x86
+Type: system ioctl
+Parameters: u64 mce_cap (out)
+Returns: 0 on success, -1 on error
+
+Returns supported MCE capabilities. The u64 mce_cap parameter
+has the same format as the MSR_IA32_MCG_CAP register. Supported
+capabilities will have the corresponding bits set.
+
+4.105 KVM_X86_SETUP_MCE
+
+Capability: KVM_CAP_MCE
+Architectures: x86
+Type: vcpu ioctl
+Parameters: u64 mcg_cap (in)
+Returns: 0 on success,
+         -EFAULT if u64 mcg_cap cannot be read,
+         -EINVAL if the requested number of banks is invalid,
+         -EINVAL if requested MCE capability is not supported.
+
+Initializes MCE support for use. The u64 mcg_cap parameter
+has the same format as the MSR_IA32_MCG_CAP register and
+specifies which capabilities should be enabled. The maximum
+supported number of error-reporting banks can be retrieved when
+checking for KVM_CAP_MCE. The supported capabilities can be
+retrieved with KVM_X86_GET_MCE_CAP_SUPPORTED.
+
+4.106 KVM_X86_SET_MCE
+
+Capability: KVM_CAP_MCE
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_x86_mce (in)
+Returns: 0 on success,
+         -EFAULT if struct kvm_x86_mce cannot be read,
+         -EINVAL if the bank number is invalid,
+         -EINVAL if VAL bit is not set in status field.
+
+Inject a machine check error (MCE) into the guest. The input
+parameter is:
+
+struct kvm_x86_mce {
+	__u64 status;
+	__u64 addr;
+	__u64 misc;
+	__u64 mcg_status;
+	__u8 bank;
+	__u8 pad1[7];
+	__u64 pad2[3];
+};
+
+If the MCE being reported is an uncorrected error, KVM will
+inject it as an MCE exception into the guest. If the guest
+MCG_STATUS register reports that an MCE is in progress, KVM
+causes an KVM_EXIT_SHUTDOWN vmexit.
+
+Otherwise, if the MCE is a corrected error, KVM will just
+store it in the corresponding bank (provided this bank is
+not holding a previously reported uncorrected error).
+
+4.107 KVM_S390_GET_CMMA_BITS
+
+Capability: KVM_CAP_S390_CMMA_MIGRATION
+Architectures: s390
+Type: vm ioctl
+Parameters: struct kvm_s390_cmma_log (in, out)
+Returns: 0 on success, a negative value on error
+
+This ioctl is used to get the values of the CMMA bits on the s390
+architecture. It is meant to be used in two scenarios:
+- During live migration to save the CMMA values. Live migration needs
+  to be enabled via the KVM_REQ_START_MIGRATION VM property.
+- To non-destructively peek at the CMMA values, with the flag
+  KVM_S390_CMMA_PEEK set.
+
+The ioctl takes parameters via the kvm_s390_cmma_log struct. The desired
+values are written to a buffer whose location is indicated via the "values"
+member in the kvm_s390_cmma_log struct.  The values in the input struct are
+also updated as needed.
+Each CMMA value takes up one byte.
+
+struct kvm_s390_cmma_log {
+	__u64 start_gfn;
+	__u32 count;
+	__u32 flags;
+	union {
+		__u64 remaining;
+		__u64 mask;
+	};
+	__u64 values;
+};
+
+start_gfn is the number of the first guest frame whose CMMA values are
+to be retrieved,
+
+count is the length of the buffer in bytes,
+
+values points to the buffer where the result will be written to.
+
+If count is greater than KVM_S390_SKEYS_MAX, then it is considered to be
+KVM_S390_SKEYS_MAX. KVM_S390_SKEYS_MAX is re-used for consistency with
+other ioctls.
+
+The result is written in the buffer pointed to by the field values, and
+the values of the input parameter are updated as follows.
+
+Depending on the flags, different actions are performed. The only
+supported flag so far is KVM_S390_CMMA_PEEK.
+
+The default behaviour if KVM_S390_CMMA_PEEK is not set is:
+start_gfn will indicate the first page frame whose CMMA bits were dirty.
+It is not necessarily the same as the one passed as input, as clean pages
+are skipped.
+
+count will indicate the number of bytes actually written in the buffer.
+It can (and very often will) be smaller than the input value, since the
+buffer is only filled until 16 bytes of clean values are found (which
+are then not copied in the buffer). Since a CMMA migration block needs
+the base address and the length, for a total of 16 bytes, we will send
+back some clean data if there is some dirty data afterwards, as long as
+the size of the clean data does not exceed the size of the header. This
+allows to minimize the amount of data to be saved or transferred over
+the network at the expense of more roundtrips to userspace. The next
+invocation of the ioctl will skip over all the clean values, saving
+potentially more than just the 16 bytes we found.
+
+If KVM_S390_CMMA_PEEK is set:
+the existing storage attributes are read even when not in migration
+mode, and no other action is performed;
+
+the output start_gfn will be equal to the input start_gfn,
+
+the output count will be equal to the input count, except if the end of
+memory has been reached.
+
+In both cases:
+the field "remaining" will indicate the total number of dirty CMMA values
+still remaining, or 0 if KVM_S390_CMMA_PEEK is set and migration mode is
+not enabled.
+
+mask is unused.
+
+values points to the userspace buffer where the result will be stored.
+
+This ioctl can fail with -ENOMEM if not enough memory can be allocated to
+complete the task, with -ENXIO if CMMA is not enabled, with -EINVAL if
+KVM_S390_CMMA_PEEK is not set but migration mode was not enabled, with
+-EFAULT if the userspace address is invalid or if no page table is
+present for the addresses (e.g. when using hugepages).
+
+4.108 KVM_S390_SET_CMMA_BITS
+
+Capability: KVM_CAP_S390_CMMA_MIGRATION
+Architectures: s390
+Type: vm ioctl
+Parameters: struct kvm_s390_cmma_log (in)
+Returns: 0 on success, a negative value on error
+
+This ioctl is used to set the values of the CMMA bits on the s390
+architecture. It is meant to be used during live migration to restore
+the CMMA values, but there are no restrictions on its use.
+The ioctl takes parameters via the kvm_s390_cmma_values struct.
+Each CMMA value takes up one byte.
+
+struct kvm_s390_cmma_log {
+	__u64 start_gfn;
+	__u32 count;
+	__u32 flags;
+	union {
+		__u64 remaining;
+		__u64 mask;
+	};
+	__u64 values;
+};
+
+start_gfn indicates the starting guest frame number,
+
+count indicates how many values are to be considered in the buffer,
+
+flags is not used and must be 0.
+
+mask indicates which PGSTE bits are to be considered.
+
+remaining is not used.
+
+values points to the buffer in userspace where to store the values.
+
+This ioctl can fail with -ENOMEM if not enough memory can be allocated to
+complete the task, with -ENXIO if CMMA is not enabled, with -EINVAL if
+the count field is too large (e.g. more than KVM_S390_CMMA_SIZE_MAX) or
+if the flags field was not 0, with -EFAULT if the userspace address is
+invalid, if invalid pages are written to (e.g. after the end of memory)
+or if no page table is present for the addresses (e.g. when using
+hugepages).
+
+4.109 KVM_PPC_GET_CPU_CHAR
+
+Capability: KVM_CAP_PPC_GET_CPU_CHAR
+Architectures: powerpc
+Type: vm ioctl
+Parameters: struct kvm_ppc_cpu_char (out)
+Returns: 0 on successful completion
+	 -EFAULT if struct kvm_ppc_cpu_char cannot be written
+
+This ioctl gives userspace information about certain characteristics
+of the CPU relating to speculative execution of instructions and
+possible information leakage resulting from speculative execution (see
+CVE-2017-5715, CVE-2017-5753 and CVE-2017-5754).  The information is
+returned in struct kvm_ppc_cpu_char, which looks like this:
+
+struct kvm_ppc_cpu_char {
+	__u64	character;		/* characteristics of the CPU */
+	__u64	behaviour;		/* recommended software behaviour */
+	__u64	character_mask;		/* valid bits in character */
+	__u64	behaviour_mask;		/* valid bits in behaviour */
+};
+
+For extensibility, the character_mask and behaviour_mask fields
+indicate which bits of character and behaviour have been filled in by
+the kernel.  If the set of defined bits is extended in future then
+userspace will be able to tell whether it is running on a kernel that
+knows about the new bits.
+
+The character field describes attributes of the CPU which can help
+with preventing inadvertent information disclosure - specifically,
+whether there is an instruction to flash-invalidate the L1 data cache
+(ori 30,30,0 or mtspr SPRN_TRIG2,rN), whether the L1 data cache is set
+to a mode where entries can only be used by the thread that created
+them, whether the bcctr[l] instruction prevents speculation, and
+whether a speculation barrier instruction (ori 31,31,0) is provided.
+
+The behaviour field describes actions that software should take to
+prevent inadvertent information disclosure, and thus describes which
+vulnerabilities the hardware is subject to; specifically whether the
+L1 data cache should be flushed when returning to user mode from the
+kernel, and whether a speculation barrier should be placed between an
+array bounds check and the array access.
+
+These fields use the same bit definitions as the new
+H_GET_CPU_CHARACTERISTICS hypercall.
+
+4.110 KVM_MEMORY_ENCRYPT_OP
+
+Capability: basic
+Architectures: x86
+Type: system
+Parameters: an opaque platform specific structure (in/out)
+Returns: 0 on success; -1 on error
+
+If the platform supports creating encrypted VMs then this ioctl can be used
+for issuing platform-specific memory encryption commands to manage those
+encrypted VMs.
+
+Currently, this ioctl is used for issuing Secure Encrypted Virtualization
+(SEV) commands on AMD Processors. The SEV commands are defined in
+Documentation/virtual/kvm/amd-memory-encryption.rst.
+
+4.111 KVM_MEMORY_ENCRYPT_REG_REGION
+
+Capability: basic
+Architectures: x86
+Type: system
+Parameters: struct kvm_enc_region (in)
+Returns: 0 on success; -1 on error
+
+This ioctl can be used to register a guest memory region which may
+contain encrypted data (e.g. guest RAM, SMRAM etc).
+
+It is used in the SEV-enabled guest. When encryption is enabled, a guest
+memory region may contain encrypted data. The SEV memory encryption
+engine uses a tweak such that two identical plaintext pages, each at
+different locations will have differing ciphertexts. So swapping or
+moving ciphertext of those pages will not result in plaintext being
+swapped. So relocating (or migrating) physical backing pages for the SEV
+guest will require some additional steps.
+
+Note: The current SEV key management spec does not provide commands to
+swap or migrate (move) ciphertext pages. Hence, for now we pin the guest
+memory region registered with the ioctl.
+
+4.112 KVM_MEMORY_ENCRYPT_UNREG_REGION
+
+Capability: basic
+Architectures: x86
+Type: system
+Parameters: struct kvm_enc_region (in)
+Returns: 0 on success; -1 on error
+
+This ioctl can be used to unregister the guest memory region registered
+with KVM_MEMORY_ENCRYPT_REG_REGION ioctl above.
+
+4.113 KVM_HYPERV_EVENTFD
+
+Capability: KVM_CAP_HYPERV_EVENTFD
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_hyperv_eventfd (in)
+
+This ioctl (un)registers an eventfd to receive notifications from the guest on
+the specified Hyper-V connection id through the SIGNAL_EVENT hypercall, without
+causing a user exit.  SIGNAL_EVENT hypercall with non-zero event flag number
+(bits 24-31) still triggers a KVM_EXIT_HYPERV_HCALL user exit.
+
+struct kvm_hyperv_eventfd {
+	__u32 conn_id;
+	__s32 fd;
+	__u32 flags;
+	__u32 padding[3];
+};
+
+The conn_id field should fit within 24 bits:
+
+#define KVM_HYPERV_CONN_ID_MASK		0x00ffffff
+
+The acceptable values for the flags field are:
+
+#define KVM_HYPERV_EVENTFD_DEASSIGN	(1 << 0)
+
+Returns: 0 on success,
+	-EINVAL if conn_id or flags is outside the allowed range
+	-ENOENT on deassign if the conn_id isn't registered
+	-EEXIST on assign if the conn_id is already registered
+
+4.114 KVM_GET_NESTED_STATE
+
+Capability: KVM_CAP_NESTED_STATE
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_nested_state (in/out)
+Returns: 0 on success, -1 on error
+Errors:
+  E2BIG:     the total state size (including the fixed-size part of struct
+             kvm_nested_state) exceeds the value of 'size' specified by
+             the user; the size required will be written into size.
+
+struct kvm_nested_state {
+	__u16 flags;
+	__u16 format;
+	__u32 size;
+	union {
+		struct kvm_vmx_nested_state vmx;
+		struct kvm_svm_nested_state svm;
+		__u8 pad[120];
+	};
+	__u8 data[0];
+};
+
+#define KVM_STATE_NESTED_GUEST_MODE	0x00000001
+#define KVM_STATE_NESTED_RUN_PENDING	0x00000002
+
+#define KVM_STATE_NESTED_SMM_GUEST_MODE	0x00000001
+#define KVM_STATE_NESTED_SMM_VMXON	0x00000002
+
+struct kvm_vmx_nested_state {
+	__u64 vmxon_pa;
+	__u64 vmcs_pa;
+
+	struct {
+		__u16 flags;
+	} smm;
+};
+
+This ioctl copies the vcpu's nested virtualization state from the kernel to
+userspace.
+
+The maximum size of the state, including the fixed-size part of struct
+kvm_nested_state, can be retrieved by passing KVM_CAP_NESTED_STATE to
+the KVM_CHECK_EXTENSION ioctl().
+
+4.115 KVM_SET_NESTED_STATE
+
+Capability: KVM_CAP_NESTED_STATE
+Architectures: x86
+Type: vcpu ioctl
+Parameters: struct kvm_nested_state (in)
+Returns: 0 on success, -1 on error
+
+This copies the vcpu's kvm_nested_state struct from userspace to the kernel.  For
+the definition of struct kvm_nested_state, see KVM_GET_NESTED_STATE.
+
+5. The kvm_run structure
+------------------------
+
+Application code obtains a pointer to the kvm_run structure by
+mmap()ing a vcpu fd.  From that point, application code can control
+execution by changing fields in kvm_run prior to calling the KVM_RUN
+ioctl, and obtain information about the reason KVM_RUN returned by
+looking up structure members.
+
+struct kvm_run {
+	/* in */
+	__u8 request_interrupt_window;
+
+Request that KVM_RUN return when it becomes possible to inject external
+interrupts into the guest.  Useful in conjunction with KVM_INTERRUPT.
+
+	__u8 immediate_exit;
+
+This field is polled once when KVM_RUN starts; if non-zero, KVM_RUN
+exits immediately, returning -EINTR.  In the common scenario where a
+signal is used to "kick" a VCPU out of KVM_RUN, this field can be used
+to avoid usage of KVM_SET_SIGNAL_MASK, which has worse scalability.
+Rather than blocking the signal outside KVM_RUN, userspace can set up
+a signal handler that sets run->immediate_exit to a non-zero value.
+
+This field is ignored if KVM_CAP_IMMEDIATE_EXIT is not available.
+
+	__u8 padding1[6];
+
+	/* out */
+	__u32 exit_reason;
+
+When KVM_RUN has returned successfully (return value 0), this informs
+application code why KVM_RUN has returned.  Allowable values for this
+field are detailed below.
+
+	__u8 ready_for_interrupt_injection;
+
+If request_interrupt_window has been specified, this field indicates
+an interrupt can be injected now with KVM_INTERRUPT.
+
+	__u8 if_flag;
+
+The value of the current interrupt flag.  Only valid if in-kernel
+local APIC is not used.
+
+	__u16 flags;
+
+More architecture-specific flags detailing state of the VCPU that may
+affect the device's behavior.  The only currently defined flag is
+KVM_RUN_X86_SMM, which is valid on x86 machines and is set if the
+VCPU is in system management mode.
+
+	/* in (pre_kvm_run), out (post_kvm_run) */
+	__u64 cr8;
+
+The value of the cr8 register.  Only valid if in-kernel local APIC is
+not used.  Both input and output.
+
+	__u64 apic_base;
+
+The value of the APIC BASE msr.  Only valid if in-kernel local
+APIC is not used.  Both input and output.
+
+	union {
+		/* KVM_EXIT_UNKNOWN */
+		struct {
+			__u64 hardware_exit_reason;
+		} hw;
+
+If exit_reason is KVM_EXIT_UNKNOWN, the vcpu has exited due to unknown
+reasons.  Further architecture-specific information is available in
+hardware_exit_reason.
+
+		/* KVM_EXIT_FAIL_ENTRY */
+		struct {
+			__u64 hardware_entry_failure_reason;
+		} fail_entry;
+
+If exit_reason is KVM_EXIT_FAIL_ENTRY, the vcpu could not be run due
+to unknown reasons.  Further architecture-specific information is
+available in hardware_entry_failure_reason.
+
+		/* KVM_EXIT_EXCEPTION */
+		struct {
+			__u32 exception;
+			__u32 error_code;
+		} ex;
+
+Unused.
+
+		/* KVM_EXIT_IO */
+		struct {
+#define KVM_EXIT_IO_IN  0
+#define KVM_EXIT_IO_OUT 1
+			__u8 direction;
+			__u8 size; /* bytes */
+			__u16 port;
+			__u32 count;
+			__u64 data_offset; /* relative to kvm_run start */
+		} io;
+
+If exit_reason is KVM_EXIT_IO, then the vcpu has
+executed a port I/O instruction which could not be satisfied by kvm.
+data_offset describes where the data is located (KVM_EXIT_IO_OUT) or
+where kvm expects application code to place the data for the next
+KVM_RUN invocation (KVM_EXIT_IO_IN).  Data format is a packed array.
+
+		/* KVM_EXIT_DEBUG */
+		struct {
+			struct kvm_debug_exit_arch arch;
+		} debug;
+
+If the exit_reason is KVM_EXIT_DEBUG, then a vcpu is processing a debug event
+for which architecture specific information is returned.
+
+		/* KVM_EXIT_MMIO */
+		struct {
+			__u64 phys_addr;
+			__u8  data[8];
+			__u32 len;
+			__u8  is_write;
+		} mmio;
+
+If exit_reason is KVM_EXIT_MMIO, then the vcpu has
+executed a memory-mapped I/O instruction which could not be satisfied
+by kvm.  The 'data' member contains the written data if 'is_write' is
+true, and should be filled by application code otherwise.
+
+The 'data' member contains, in its first 'len' bytes, the value as it would
+appear if the VCPU performed a load or store of the appropriate width directly
+to the byte array.
+
+NOTE: For KVM_EXIT_IO, KVM_EXIT_MMIO, KVM_EXIT_OSI, KVM_EXIT_PAPR and
+      KVM_EXIT_EPR the corresponding
+operations are complete (and guest state is consistent) only after userspace
+has re-entered the kernel with KVM_RUN.  The kernel side will first finish
+incomplete operations and then check for pending signals.  Userspace
+can re-enter the guest with an unmasked signal pending to complete
+pending operations.
+
+		/* KVM_EXIT_HYPERCALL */
+		struct {
+			__u64 nr;
+			__u64 args[6];
+			__u64 ret;
+			__u32 longmode;
+			__u32 pad;
+		} hypercall;
+
+Unused.  This was once used for 'hypercall to userspace'.  To implement
+such functionality, use KVM_EXIT_IO (x86) or KVM_EXIT_MMIO (all except s390).
+Note KVM_EXIT_IO is significantly faster than KVM_EXIT_MMIO.
+
+		/* KVM_EXIT_TPR_ACCESS */
+		struct {
+			__u64 rip;
+			__u32 is_write;
+			__u32 pad;
+		} tpr_access;
+
+To be documented (KVM_TPR_ACCESS_REPORTING).
+
+		/* KVM_EXIT_S390_SIEIC */
+		struct {
+			__u8 icptcode;
+			__u64 mask; /* psw upper half */
+			__u64 addr; /* psw lower half */
+			__u16 ipa;
+			__u32 ipb;
+		} s390_sieic;
+
+s390 specific.
+
+		/* KVM_EXIT_S390_RESET */
+#define KVM_S390_RESET_POR       1
+#define KVM_S390_RESET_CLEAR     2
+#define KVM_S390_RESET_SUBSYSTEM 4
+#define KVM_S390_RESET_CPU_INIT  8
+#define KVM_S390_RESET_IPL       16
+		__u64 s390_reset_flags;
+
+s390 specific.
+
+		/* KVM_EXIT_S390_UCONTROL */
+		struct {
+			__u64 trans_exc_code;
+			__u32 pgm_code;
+		} s390_ucontrol;
+
+s390 specific. A page fault has occurred for a user controlled virtual
+machine (KVM_VM_S390_UNCONTROL) on it's host page table that cannot be
+resolved by the kernel.
+The program code and the translation exception code that were placed
+in the cpu's lowcore are presented here as defined by the z Architecture
+Principles of Operation Book in the Chapter for Dynamic Address Translation
+(DAT)
+
+		/* KVM_EXIT_DCR */
+		struct {
+			__u32 dcrn;
+			__u32 data;
+			__u8  is_write;
+		} dcr;
+
+Deprecated - was used for 440 KVM.
+
+		/* KVM_EXIT_OSI */
+		struct {
+			__u64 gprs[32];
+		} osi;
+
+MOL uses a special hypercall interface it calls 'OSI'. To enable it, we catch
+hypercalls and exit with this exit struct that contains all the guest gprs.
+
+If exit_reason is KVM_EXIT_OSI, then the vcpu has triggered such a hypercall.
+Userspace can now handle the hypercall and when it's done modify the gprs as
+necessary. Upon guest entry all guest GPRs will then be replaced by the values
+in this struct.
+
+		/* KVM_EXIT_PAPR_HCALL */
+		struct {
+			__u64 nr;
+			__u64 ret;
+			__u64 args[9];
+		} papr_hcall;
+
+This is used on 64-bit PowerPC when emulating a pSeries partition,
+e.g. with the 'pseries' machine type in qemu.  It occurs when the
+guest does a hypercall using the 'sc 1' instruction.  The 'nr' field
+contains the hypercall number (from the guest R3), and 'args' contains
+the arguments (from the guest R4 - R12).  Userspace should put the
+return code in 'ret' and any extra returned values in args[].
+The possible hypercalls are defined in the Power Architecture Platform
+Requirements (PAPR) document available from www.power.org (free
+developer registration required to access it).
+
+		/* KVM_EXIT_S390_TSCH */
+		struct {
+			__u16 subchannel_id;
+			__u16 subchannel_nr;
+			__u32 io_int_parm;
+			__u32 io_int_word;
+			__u32 ipb;
+			__u8 dequeued;
+		} s390_tsch;
+
+s390 specific. This exit occurs when KVM_CAP_S390_CSS_SUPPORT has been enabled
+and TEST SUBCHANNEL was intercepted. If dequeued is set, a pending I/O
+interrupt for the target subchannel has been dequeued and subchannel_id,
+subchannel_nr, io_int_parm and io_int_word contain the parameters for that
+interrupt. ipb is needed for instruction parameter decoding.
+
+		/* KVM_EXIT_EPR */
+		struct {
+			__u32 epr;
+		} epr;
+
+On FSL BookE PowerPC chips, the interrupt controller has a fast patch
+interrupt acknowledge path to the core. When the core successfully
+delivers an interrupt, it automatically populates the EPR register with
+the interrupt vector number and acknowledges the interrupt inside
+the interrupt controller.
+
+In case the interrupt controller lives in user space, we need to do
+the interrupt acknowledge cycle through it to fetch the next to be
+delivered interrupt vector using this exit.
+
+It gets triggered whenever both KVM_CAP_PPC_EPR are enabled and an
+external interrupt has just been delivered into the guest. User space
+should put the acknowledged interrupt vector into the 'epr' field.
+
+		/* KVM_EXIT_SYSTEM_EVENT */
+		struct {
+#define KVM_SYSTEM_EVENT_SHUTDOWN       1
+#define KVM_SYSTEM_EVENT_RESET          2
+#define KVM_SYSTEM_EVENT_CRASH          3
+			__u32 type;
+			__u64 flags;
+		} system_event;
+
+If exit_reason is KVM_EXIT_SYSTEM_EVENT then the vcpu has triggered
+a system-level event using some architecture specific mechanism (hypercall
+or some special instruction). In case of ARM/ARM64, this is triggered using
+HVC instruction based PSCI call from the vcpu. The 'type' field describes
+the system-level event type. The 'flags' field describes architecture
+specific flags for the system-level event.
+
+Valid values for 'type' are:
+  KVM_SYSTEM_EVENT_SHUTDOWN -- the guest has requested a shutdown of the
+   VM. Userspace is not obliged to honour this, and if it does honour
+   this does not need to destroy the VM synchronously (ie it may call
+   KVM_RUN again before shutdown finally occurs).
+  KVM_SYSTEM_EVENT_RESET -- the guest has requested a reset of the VM.
+   As with SHUTDOWN, userspace can choose to ignore the request, or
+   to schedule the reset to occur in the future and may call KVM_RUN again.
+  KVM_SYSTEM_EVENT_CRASH -- the guest crash occurred and the guest
+   has requested a crash condition maintenance. Userspace can choose
+   to ignore the request, or to gather VM memory core dump and/or
+   reset/shutdown of the VM.
+
+		/* KVM_EXIT_IOAPIC_EOI */
+		struct {
+			__u8 vector;
+		} eoi;
+
+Indicates that the VCPU's in-kernel local APIC received an EOI for a
+level-triggered IOAPIC interrupt.  This exit only triggers when the
+IOAPIC is implemented in userspace (i.e. KVM_CAP_SPLIT_IRQCHIP is enabled);
+the userspace IOAPIC should process the EOI and retrigger the interrupt if
+it is still asserted.  Vector is the LAPIC interrupt vector for which the
+EOI was received.
+
+		struct kvm_hyperv_exit {
+#define KVM_EXIT_HYPERV_SYNIC          1
+#define KVM_EXIT_HYPERV_HCALL          2
+			__u32 type;
+			union {
+				struct {
+					__u32 msr;
+					__u64 control;
+					__u64 evt_page;
+					__u64 msg_page;
+				} synic;
+				struct {
+					__u64 input;
+					__u64 result;
+					__u64 params[2];
+				} hcall;
+			} u;
+		};
+		/* KVM_EXIT_HYPERV */
+                struct kvm_hyperv_exit hyperv;
+Indicates that the VCPU exits into userspace to process some tasks
+related to Hyper-V emulation.
+Valid values for 'type' are:
+	KVM_EXIT_HYPERV_SYNIC -- synchronously notify user-space about
+Hyper-V SynIC state change. Notification is used to remap SynIC
+event/message pages and to enable/disable SynIC messages/events processing
+in userspace.
+
+		/* Fix the size of the union. */
+		char padding[256];
+	};
+
+	/*
+	 * shared registers between kvm and userspace.
+	 * kvm_valid_regs specifies the register classes set by the host
+	 * kvm_dirty_regs specified the register classes dirtied by userspace
+	 * struct kvm_sync_regs is architecture specific, as well as the
+	 * bits for kvm_valid_regs and kvm_dirty_regs
+	 */
+	__u64 kvm_valid_regs;
+	__u64 kvm_dirty_regs;
+	union {
+		struct kvm_sync_regs regs;
+		char padding[SYNC_REGS_SIZE_BYTES];
+	} s;
+
+If KVM_CAP_SYNC_REGS is defined, these fields allow userspace to access
+certain guest registers without having to call SET/GET_*REGS. Thus we can
+avoid some system call overhead if userspace has to handle the exit.
+Userspace can query the validity of the structure by checking
+kvm_valid_regs for specific bits. These bits are architecture specific
+and usually define the validity of a groups of registers. (e.g. one bit
+ for general purpose registers)
+
+Please note that the kernel is allowed to use the kvm_run structure as the
+primary storage for certain register types. Therefore, the kernel may use the
+values in kvm_run even if the corresponding bit in kvm_dirty_regs is not set.
+
+};
+
+
+
+6. Capabilities that can be enabled on vCPUs
+--------------------------------------------
+
+There are certain capabilities that change the behavior of the virtual CPU or
+the virtual machine when enabled. To enable them, please see section 4.37.
+Below you can find a list of capabilities and what their effect on the vCPU or
+the virtual machine is when enabling them.
+
+The following information is provided along with the description:
+
+  Architectures: which instruction set architectures provide this ioctl.
+      x86 includes both i386 and x86_64.
+
+  Target: whether this is a per-vcpu or per-vm capability.
+
+  Parameters: what parameters are accepted by the capability.
+
+  Returns: the return value.  General error numbers (EBADF, ENOMEM, EINVAL)
+      are not detailed, but errors with specific meanings are.
+
+
+6.1 KVM_CAP_PPC_OSI
+
+Architectures: ppc
+Target: vcpu
+Parameters: none
+Returns: 0 on success; -1 on error
+
+This capability enables interception of OSI hypercalls that otherwise would
+be treated as normal system calls to be injected into the guest. OSI hypercalls
+were invented by Mac-on-Linux to have a standardized communication mechanism
+between the guest and the host.
+
+When this capability is enabled, KVM_EXIT_OSI can occur.
+
+
+6.2 KVM_CAP_PPC_PAPR
+
+Architectures: ppc
+Target: vcpu
+Parameters: none
+Returns: 0 on success; -1 on error
+
+This capability enables interception of PAPR hypercalls. PAPR hypercalls are
+done using the hypercall instruction "sc 1".
+
+It also sets the guest privilege level to "supervisor" mode. Usually the guest
+runs in "hypervisor" privilege mode with a few missing features.
+
+In addition to the above, it changes the semantics of SDR1. In this mode, the
+HTAB address part of SDR1 contains an HVA instead of a GPA, as PAPR keeps the
+HTAB invisible to the guest.
+
+When this capability is enabled, KVM_EXIT_PAPR_HCALL can occur.
+
+
+6.3 KVM_CAP_SW_TLB
+
+Architectures: ppc
+Target: vcpu
+Parameters: args[0] is the address of a struct kvm_config_tlb
+Returns: 0 on success; -1 on error
+
+struct kvm_config_tlb {
+	__u64 params;
+	__u64 array;
+	__u32 mmu_type;
+	__u32 array_len;
+};
+
+Configures the virtual CPU's TLB array, establishing a shared memory area
+between userspace and KVM.  The "params" and "array" fields are userspace
+addresses of mmu-type-specific data structures.  The "array_len" field is an
+safety mechanism, and should be set to the size in bytes of the memory that
+userspace has reserved for the array.  It must be at least the size dictated
+by "mmu_type" and "params".
+
+While KVM_RUN is active, the shared region is under control of KVM.  Its
+contents are undefined, and any modification by userspace results in
+boundedly undefined behavior.
+
+On return from KVM_RUN, the shared region will reflect the current state of
+the guest's TLB.  If userspace makes any changes, it must call KVM_DIRTY_TLB
+to tell KVM which entries have been changed, prior to calling KVM_RUN again
+on this vcpu.
+
+For mmu types KVM_MMU_FSL_BOOKE_NOHV and KVM_MMU_FSL_BOOKE_HV:
+ - The "params" field is of type "struct kvm_book3e_206_tlb_params".
+ - The "array" field points to an array of type "struct
+   kvm_book3e_206_tlb_entry".
+ - The array consists of all entries in the first TLB, followed by all
+   entries in the second TLB.
+ - Within a TLB, entries are ordered first by increasing set number.  Within a
+   set, entries are ordered by way (increasing ESEL).
+ - The hash for determining set number in TLB0 is: (MAS2 >> 12) & (num_sets - 1)
+   where "num_sets" is the tlb_sizes[] value divided by the tlb_ways[] value.
+ - The tsize field of mas1 shall be set to 4K on TLB0, even though the
+   hardware ignores this value for TLB0.
+
+6.4 KVM_CAP_S390_CSS_SUPPORT
+
+Architectures: s390
+Target: vcpu
+Parameters: none
+Returns: 0 on success; -1 on error
+
+This capability enables support for handling of channel I/O instructions.
+
+TEST PENDING INTERRUPTION and the interrupt portion of TEST SUBCHANNEL are
+handled in-kernel, while the other I/O instructions are passed to userspace.
+
+When this capability is enabled, KVM_EXIT_S390_TSCH will occur on TEST
+SUBCHANNEL intercepts.
+
+Note that even though this capability is enabled per-vcpu, the complete
+virtual machine is affected.
+
+6.5 KVM_CAP_PPC_EPR
+
+Architectures: ppc
+Target: vcpu
+Parameters: args[0] defines whether the proxy facility is active
+Returns: 0 on success; -1 on error
+
+This capability enables or disables the delivery of interrupts through the
+external proxy facility.
+
+When enabled (args[0] != 0), every time the guest gets an external interrupt
+delivered, it automatically exits into user space with a KVM_EXIT_EPR exit
+to receive the topmost interrupt vector.
+
+When disabled (args[0] == 0), behavior is as if this facility is unsupported.
+
+When this capability is enabled, KVM_EXIT_EPR can occur.
+
+6.6 KVM_CAP_IRQ_MPIC
+
+Architectures: ppc
+Parameters: args[0] is the MPIC device fd
+            args[1] is the MPIC CPU number for this vcpu
+
+This capability connects the vcpu to an in-kernel MPIC device.
+
+6.7 KVM_CAP_IRQ_XICS
+
+Architectures: ppc
+Target: vcpu
+Parameters: args[0] is the XICS device fd
+            args[1] is the XICS CPU number (server ID) for this vcpu
+
+This capability connects the vcpu to an in-kernel XICS device.
+
+6.8 KVM_CAP_S390_IRQCHIP
+
+Architectures: s390
+Target: vm
+Parameters: none
+
+This capability enables the in-kernel irqchip for s390. Please refer to
+"4.24 KVM_CREATE_IRQCHIP" for details.
+
+6.9 KVM_CAP_MIPS_FPU
+
+Architectures: mips
+Target: vcpu
+Parameters: args[0] is reserved for future use (should be 0).
+
+This capability allows the use of the host Floating Point Unit by the guest. It
+allows the Config1.FP bit to be set to enable the FPU in the guest. Once this is
+done the KVM_REG_MIPS_FPR_* and KVM_REG_MIPS_FCR_* registers can be accessed
+(depending on the current guest FPU register mode), and the Status.FR,
+Config5.FRE bits are accessible via the KVM API and also from the guest,
+depending on them being supported by the FPU.
+
+6.10 KVM_CAP_MIPS_MSA
+
+Architectures: mips
+Target: vcpu
+Parameters: args[0] is reserved for future use (should be 0).
+
+This capability allows the use of the MIPS SIMD Architecture (MSA) by the guest.
+It allows the Config3.MSAP bit to be set to enable the use of MSA by the guest.
+Once this is done the KVM_REG_MIPS_VEC_* and KVM_REG_MIPS_MSA_* registers can be
+accessed, and the Config5.MSAEn bit is accessible via the KVM API and also from
+the guest.
+
+6.74 KVM_CAP_SYNC_REGS
+Architectures: s390, x86
+Target: s390: always enabled, x86: vcpu
+Parameters: none
+Returns: x86: KVM_CHECK_EXTENSION returns a bit-array indicating which register
+sets are supported (bitfields defined in arch/x86/include/uapi/asm/kvm.h).
+
+As described above in the kvm_sync_regs struct info in section 5 (kvm_run):
+KVM_CAP_SYNC_REGS "allow[s] userspace to access certain guest registers
+without having to call SET/GET_*REGS". This reduces overhead by eliminating
+repeated ioctl calls for setting and/or getting register values. This is
+particularly important when userspace is making synchronous guest state
+modifications, e.g. when emulating and/or intercepting instructions in
+userspace.
+
+For s390 specifics, please refer to the source code.
+
+For x86:
+- the register sets to be copied out to kvm_run are selectable
+  by userspace (rather that all sets being copied out for every exit).
+- vcpu_events are available in addition to regs and sregs.
+
+For x86, the 'kvm_valid_regs' field of struct kvm_run is overloaded to
+function as an input bit-array field set by userspace to indicate the
+specific register sets to be copied out on the next exit.
+
+To indicate when userspace has modified values that should be copied into
+the vCPU, the all architecture bitarray field, 'kvm_dirty_regs' must be set.
+This is done using the same bitflags as for the 'kvm_valid_regs' field.
+If the dirty bit is not set, then the register set values will not be copied
+into the vCPU even if they've been modified.
+
+Unused bitfields in the bitarrays must be set to zero.
+
+struct kvm_sync_regs {
+        struct kvm_regs regs;
+        struct kvm_sregs sregs;
+        struct kvm_vcpu_events events;
+};
+
+7. Capabilities that can be enabled on VMs
+------------------------------------------
+
+There are certain capabilities that change the behavior of the virtual
+machine when enabled. To enable them, please see section 4.37. Below
+you can find a list of capabilities and what their effect on the VM
+is when enabling them.
+
+The following information is provided along with the description:
+
+  Architectures: which instruction set architectures provide this ioctl.
+      x86 includes both i386 and x86_64.
+
+  Parameters: what parameters are accepted by the capability.
+
+  Returns: the return value.  General error numbers (EBADF, ENOMEM, EINVAL)
+      are not detailed, but errors with specific meanings are.
+
+
+7.1 KVM_CAP_PPC_ENABLE_HCALL
+
+Architectures: ppc
+Parameters: args[0] is the sPAPR hcall number
+	    args[1] is 0 to disable, 1 to enable in-kernel handling
+
+This capability controls whether individual sPAPR hypercalls (hcalls)
+get handled by the kernel or not.  Enabling or disabling in-kernel
+handling of an hcall is effective across the VM.  On creation, an
+initial set of hcalls are enabled for in-kernel handling, which
+consists of those hcalls for which in-kernel handlers were implemented
+before this capability was implemented.  If disabled, the kernel will
+not to attempt to handle the hcall, but will always exit to userspace
+to handle it.  Note that it may not make sense to enable some and
+disable others of a group of related hcalls, but KVM does not prevent
+userspace from doing that.
+
+If the hcall number specified is not one that has an in-kernel
+implementation, the KVM_ENABLE_CAP ioctl will fail with an EINVAL
+error.
+
+7.2 KVM_CAP_S390_USER_SIGP
+
+Architectures: s390
+Parameters: none
+
+This capability controls which SIGP orders will be handled completely in user
+space. With this capability enabled, all fast orders will be handled completely
+in the kernel:
+- SENSE
+- SENSE RUNNING
+- EXTERNAL CALL
+- EMERGENCY SIGNAL
+- CONDITIONAL EMERGENCY SIGNAL
+
+All other orders will be handled completely in user space.
+
+Only privileged operation exceptions will be checked for in the kernel (or even
+in the hardware prior to interception). If this capability is not enabled, the
+old way of handling SIGP orders is used (partially in kernel and user space).
+
+7.3 KVM_CAP_S390_VECTOR_REGISTERS
+
+Architectures: s390
+Parameters: none
+Returns: 0 on success, negative value on error
+
+Allows use of the vector registers introduced with z13 processor, and
+provides for the synchronization between host and user space.  Will
+return -EINVAL if the machine does not support vectors.
+
+7.4 KVM_CAP_S390_USER_STSI
+
+Architectures: s390
+Parameters: none
+
+This capability allows post-handlers for the STSI instruction. After
+initial handling in the kernel, KVM exits to user space with
+KVM_EXIT_S390_STSI to allow user space to insert further data.
+
+Before exiting to userspace, kvm handlers should fill in s390_stsi field of
+vcpu->run:
+struct {
+	__u64 addr;
+	__u8 ar;
+	__u8 reserved;
+	__u8 fc;
+	__u8 sel1;
+	__u16 sel2;
+} s390_stsi;
+
+@addr - guest address of STSI SYSIB
+@fc   - function code
+@sel1 - selector 1
+@sel2 - selector 2
+@ar   - access register number
+
+KVM handlers should exit to userspace with rc = -EREMOTE.
+
+7.5 KVM_CAP_SPLIT_IRQCHIP
+
+Architectures: x86
+Parameters: args[0] - number of routes reserved for userspace IOAPICs
+Returns: 0 on success, -1 on error
+
+Create a local apic for each processor in the kernel. This can be used
+instead of KVM_CREATE_IRQCHIP if the userspace VMM wishes to emulate the
+IOAPIC and PIC (and also the PIT, even though this has to be enabled
+separately).
+
+This capability also enables in kernel routing of interrupt requests;
+when KVM_CAP_SPLIT_IRQCHIP only routes of KVM_IRQ_ROUTING_MSI type are
+used in the IRQ routing table.  The first args[0] MSI routes are reserved
+for the IOAPIC pins.  Whenever the LAPIC receives an EOI for these routes,
+a KVM_EXIT_IOAPIC_EOI vmexit will be reported to userspace.
+
+Fails if VCPU has already been created, or if the irqchip is already in the
+kernel (i.e. KVM_CREATE_IRQCHIP has already been called).
+
+7.6 KVM_CAP_S390_RI
+
+Architectures: s390
+Parameters: none
+
+Allows use of runtime-instrumentation introduced with zEC12 processor.
+Will return -EINVAL if the machine does not support runtime-instrumentation.
+Will return -EBUSY if a VCPU has already been created.
+
+7.7 KVM_CAP_X2APIC_API
+
+Architectures: x86
+Parameters: args[0] - features that should be enabled
+Returns: 0 on success, -EINVAL when args[0] contains invalid features
+
+Valid feature flags in args[0] are
+
+#define KVM_X2APIC_API_USE_32BIT_IDS            (1ULL << 0)
+#define KVM_X2APIC_API_DISABLE_BROADCAST_QUIRK  (1ULL << 1)
+
+Enabling KVM_X2APIC_API_USE_32BIT_IDS changes the behavior of
+KVM_SET_GSI_ROUTING, KVM_SIGNAL_MSI, KVM_SET_LAPIC, and KVM_GET_LAPIC,
+allowing the use of 32-bit APIC IDs.  See KVM_CAP_X2APIC_API in their
+respective sections.
+
+KVM_X2APIC_API_DISABLE_BROADCAST_QUIRK must be enabled for x2APIC to work
+in logical mode or with more than 255 VCPUs.  Otherwise, KVM treats 0xff
+as a broadcast even in x2APIC mode in order to support physical x2APIC
+without interrupt remapping.  This is undesirable in logical mode,
+where 0xff represents CPUs 0-7 in cluster 0.
+
+7.8 KVM_CAP_S390_USER_INSTR0
+
+Architectures: s390
+Parameters: none
+
+With this capability enabled, all illegal instructions 0x0000 (2 bytes) will
+be intercepted and forwarded to user space. User space can use this
+mechanism e.g. to realize 2-byte software breakpoints. The kernel will
+not inject an operating exception for these instructions, user space has
+to take care of that.
+
+This capability can be enabled dynamically even if VCPUs were already
+created and are running.
+
+7.9 KVM_CAP_S390_GS
+
+Architectures: s390
+Parameters: none
+Returns: 0 on success; -EINVAL if the machine does not support
+	 guarded storage; -EBUSY if a VCPU has already been created.
+
+Allows use of guarded storage for the KVM guest.
+
+7.10 KVM_CAP_S390_AIS
+
+Architectures: s390
+Parameters: none
+
+Allow use of adapter-interruption suppression.
+Returns: 0 on success; -EBUSY if a VCPU has already been created.
+
+7.11 KVM_CAP_PPC_SMT
+
+Architectures: ppc
+Parameters: vsmt_mode, flags
+
+Enabling this capability on a VM provides userspace with a way to set
+the desired virtual SMT mode (i.e. the number of virtual CPUs per
+virtual core).  The virtual SMT mode, vsmt_mode, must be a power of 2
+between 1 and 8.  On POWER8, vsmt_mode must also be no greater than
+the number of threads per subcore for the host.  Currently flags must
+be 0.  A successful call to enable this capability will result in
+vsmt_mode being returned when the KVM_CAP_PPC_SMT capability is
+subsequently queried for the VM.  This capability is only supported by
+HV KVM, and can only be set before any VCPUs have been created.
+The KVM_CAP_PPC_SMT_POSSIBLE capability indicates which virtual SMT
+modes are available.
+
+7.12 KVM_CAP_PPC_FWNMI
+
+Architectures: ppc
+Parameters: none
+
+With this capability a machine check exception in the guest address
+space will cause KVM to exit the guest with NMI exit reason. This
+enables QEMU to build error log and branch to guest kernel registered
+machine check handling routine. Without this capability KVM will
+branch to guests' 0x200 interrupt vector.
+
+7.13 KVM_CAP_X86_DISABLE_EXITS
+
+Architectures: x86
+Parameters: args[0] defines which exits are disabled
+Returns: 0 on success, -EINVAL when args[0] contains invalid exits
+
+Valid bits in args[0] are
+
+#define KVM_X86_DISABLE_EXITS_MWAIT            (1 << 0)
+#define KVM_X86_DISABLE_EXITS_HLT              (1 << 1)
+
+Enabling this capability on a VM provides userspace with a way to no
+longer intercept some instructions for improved latency in some
+workloads, and is suggested when vCPUs are associated to dedicated
+physical CPUs.  More bits can be added in the future; userspace can
+just pass the KVM_CHECK_EXTENSION result to KVM_ENABLE_CAP to disable
+all such vmexits.
+
+Do not enable KVM_FEATURE_PV_UNHALT if you disable HLT exits.
+
+7.14 KVM_CAP_S390_HPAGE_1M
+
+Architectures: s390
+Parameters: none
+Returns: 0 on success, -EINVAL if hpage module parameter was not set
+	 or cmma is enabled, or the VM has the KVM_VM_S390_UCONTROL
+	 flag set
+
+With this capability the KVM support for memory backing with 1m pages
+through hugetlbfs can be enabled for a VM. After the capability is
+enabled, cmma can't be enabled anymore and pfmfi and the storage key
+interpretation are disabled. If cmma has already been enabled or the
+hpage module parameter is not set to 1, -EINVAL is returned.
+
+While it is generally possible to create a huge page backed VM without
+this capability, the VM will not be able to run.
+
+7.14 KVM_CAP_MSR_PLATFORM_INFO
+
+Architectures: x86
+Parameters: args[0] whether feature should be enabled or not
+
+With this capability, a guest may read the MSR_PLATFORM_INFO MSR. Otherwise,
+a #GP would be raised when the guest tries to access. Currently, this
+capability does not enable write permissions of this MSR for the guest.
+
+8. Other capabilities.
+----------------------
+
+This section lists capabilities that give information about other
+features of the KVM implementation.
+
+8.1 KVM_CAP_PPC_HWRNG
+
+Architectures: ppc
+
+This capability, if KVM_CHECK_EXTENSION indicates that it is
+available, means that that the kernel has an implementation of the
+H_RANDOM hypercall backed by a hardware random-number generator.
+If present, the kernel H_RANDOM handler can be enabled for guest use
+with the KVM_CAP_PPC_ENABLE_HCALL capability.
+
+8.2 KVM_CAP_HYPERV_SYNIC
+
+Architectures: x86
+This capability, if KVM_CHECK_EXTENSION indicates that it is
+available, means that that the kernel has an implementation of the
+Hyper-V Synthetic interrupt controller(SynIC). Hyper-V SynIC is
+used to support Windows Hyper-V based guest paravirt drivers(VMBus).
+
+In order to use SynIC, it has to be activated by setting this
+capability via KVM_ENABLE_CAP ioctl on the vcpu fd. Note that this
+will disable the use of APIC hardware virtualization even if supported
+by the CPU, as it's incompatible with SynIC auto-EOI behavior.
+
+8.3 KVM_CAP_PPC_RADIX_MMU
+
+Architectures: ppc
+
+This capability, if KVM_CHECK_EXTENSION indicates that it is
+available, means that that the kernel can support guests using the
+radix MMU defined in Power ISA V3.00 (as implemented in the POWER9
+processor).
+
+8.4 KVM_CAP_PPC_HASH_MMU_V3
+
+Architectures: ppc
+
+This capability, if KVM_CHECK_EXTENSION indicates that it is
+available, means that that the kernel can support guests using the
+hashed page table MMU defined in Power ISA V3.00 (as implemented in
+the POWER9 processor), including in-memory segment tables.
+
+8.5 KVM_CAP_MIPS_VZ
+
+Architectures: mips
+
+This capability, if KVM_CHECK_EXTENSION on the main kvm handle indicates that
+it is available, means that full hardware assisted virtualization capabilities
+of the hardware are available for use through KVM. An appropriate
+KVM_VM_MIPS_* type must be passed to KVM_CREATE_VM to create a VM which
+utilises it.
+
+If KVM_CHECK_EXTENSION on a kvm VM handle indicates that this capability is
+available, it means that the VM is using full hardware assisted virtualization
+capabilities of the hardware. This is useful to check after creating a VM with
+KVM_VM_MIPS_DEFAULT.
+
+The value returned by KVM_CHECK_EXTENSION should be compared against known
+values (see below). All other values are reserved. This is to allow for the
+possibility of other hardware assisted virtualization implementations which
+may be incompatible with the MIPS VZ ASE.
+
+ 0: The trap & emulate implementation is in use to run guest code in user
+    mode. Guest virtual memory segments are rearranged to fit the guest in the
+    user mode address space.
+
+ 1: The MIPS VZ ASE is in use, providing full hardware assisted
+    virtualization, including standard guest virtual memory segments.
+
+8.6 KVM_CAP_MIPS_TE
+
+Architectures: mips
+
+This capability, if KVM_CHECK_EXTENSION on the main kvm handle indicates that
+it is available, means that the trap & emulate implementation is available to
+run guest code in user mode, even if KVM_CAP_MIPS_VZ indicates that hardware
+assisted virtualisation is also available. KVM_VM_MIPS_TE (0) must be passed
+to KVM_CREATE_VM to create a VM which utilises it.
+
+If KVM_CHECK_EXTENSION on a kvm VM handle indicates that this capability is
+available, it means that the VM is using trap & emulate.
+
+8.7 KVM_CAP_MIPS_64BIT
+
+Architectures: mips
+
+This capability indicates the supported architecture type of the guest, i.e. the
+supported register and address width.
+
+The values returned when this capability is checked by KVM_CHECK_EXTENSION on a
+kvm VM handle correspond roughly to the CP0_Config.AT register field, and should
+be checked specifically against known values (see below). All other values are
+reserved.
+
+ 0: MIPS32 or microMIPS32.
+    Both registers and addresses are 32-bits wide.
+    It will only be possible to run 32-bit guest code.
+
+ 1: MIPS64 or microMIPS64 with access only to 32-bit compatibility segments.
+    Registers are 64-bits wide, but addresses are 32-bits wide.
+    64-bit guest code may run but cannot access MIPS64 memory segments.
+    It will also be possible to run 32-bit guest code.
+
+ 2: MIPS64 or microMIPS64 with access to all address segments.
+    Both registers and addresses are 64-bits wide.
+    It will be possible to run 64-bit or 32-bit guest code.
+
+8.9 KVM_CAP_ARM_USER_IRQ
+
+Architectures: arm, arm64
+This capability, if KVM_CHECK_EXTENSION indicates that it is available, means
+that if userspace creates a VM without an in-kernel interrupt controller, it
+will be notified of changes to the output level of in-kernel emulated devices,
+which can generate virtual interrupts, presented to the VM.
+For such VMs, on every return to userspace, the kernel
+updates the vcpu's run->s.regs.device_irq_level field to represent the actual
+output level of the device.
+
+Whenever kvm detects a change in the device output level, kvm guarantees at
+least one return to userspace before running the VM.  This exit could either
+be a KVM_EXIT_INTR or any other exit event, like KVM_EXIT_MMIO. This way,
+userspace can always sample the device output level and re-compute the state of
+the userspace interrupt controller.  Userspace should always check the state
+of run->s.regs.device_irq_level on every kvm exit.
+The value in run->s.regs.device_irq_level can represent both level and edge
+triggered interrupt signals, depending on the device.  Edge triggered interrupt
+signals will exit to userspace with the bit in run->s.regs.device_irq_level
+set exactly once per edge signal.
+
+The field run->s.regs.device_irq_level is available independent of
+run->kvm_valid_regs or run->kvm_dirty_regs bits.
+
+If KVM_CAP_ARM_USER_IRQ is supported, the KVM_CHECK_EXTENSION ioctl returns a
+number larger than 0 indicating the version of this capability is implemented
+and thereby which bits in in run->s.regs.device_irq_level can signal values.
+
+Currently the following bits are defined for the device_irq_level bitmap:
+
+  KVM_CAP_ARM_USER_IRQ >= 1:
+
+    KVM_ARM_DEV_EL1_VTIMER -  EL1 virtual timer
+    KVM_ARM_DEV_EL1_PTIMER -  EL1 physical timer
+    KVM_ARM_DEV_PMU        -  ARM PMU overflow interrupt signal
+
+Future versions of kvm may implement additional events. These will get
+indicated by returning a higher number from KVM_CHECK_EXTENSION and will be
+listed above.
+
+8.10 KVM_CAP_PPC_SMT_POSSIBLE
+
+Architectures: ppc
+
+Querying this capability returns a bitmap indicating the possible
+virtual SMT modes that can be set using KVM_CAP_PPC_SMT.  If bit N
+(counting from the right) is set, then a virtual SMT mode of 2^N is
+available.
+
+8.11 KVM_CAP_HYPERV_SYNIC2
+
+Architectures: x86
+
+This capability enables a newer version of Hyper-V Synthetic interrupt
+controller (SynIC).  The only difference with KVM_CAP_HYPERV_SYNIC is that KVM
+doesn't clear SynIC message and event flags pages when they are enabled by
+writing to the respective MSRs.
+
+8.12 KVM_CAP_HYPERV_VP_INDEX
+
+Architectures: x86
+
+This capability indicates that userspace can load HV_X64_MSR_VP_INDEX msr.  Its
+value is used to denote the target vcpu for a SynIC interrupt.  For
+compatibilty, KVM initializes this msr to KVM's internal vcpu index.  When this
+capability is absent, userspace can still query this msr's value.
+
+8.13 KVM_CAP_S390_AIS_MIGRATION
+
+Architectures: s390
+Parameters: none
+
+This capability indicates if the flic device will be able to get/set the
+AIS states for migration via the KVM_DEV_FLIC_AISM_ALL attribute and allows
+to discover this without having to create a flic device.
+
+8.14 KVM_CAP_S390_PSW
+
+Architectures: s390
+
+This capability indicates that the PSW is exposed via the kvm_run structure.
+
+8.15 KVM_CAP_S390_GMAP
+
+Architectures: s390
+
+This capability indicates that the user space memory used as guest mapping can
+be anywhere in the user memory address space, as long as the memory slots are
+aligned and sized to a segment (1MB) boundary.
+
+8.16 KVM_CAP_S390_COW
+
+Architectures: s390
+
+This capability indicates that the user space memory used as guest mapping can
+use copy-on-write semantics as well as dirty pages tracking via read-only page
+tables.
+
+8.17 KVM_CAP_S390_BPB
+
+Architectures: s390
+
+This capability indicates that kvm will implement the interfaces to handle
+reset, migration and nested KVM for branch prediction blocking. The stfle
+facility 82 should not be provided to the guest without this capability.
+
+8.18 KVM_CAP_HYPERV_TLBFLUSH
+
+Architectures: x86
+
+This capability indicates that KVM supports paravirtualized Hyper-V TLB Flush
+hypercalls:
+HvFlushVirtualAddressSpace, HvFlushVirtualAddressSpaceEx,
+HvFlushVirtualAddressList, HvFlushVirtualAddressListEx.
+
+8.19 KVM_CAP_ARM_INJECT_SERROR_ESR
+
+Architectures: arm, arm64
+
+This capability indicates that userspace can specify (via the
+KVM_SET_VCPU_EVENTS ioctl) the syndrome value reported to the guest when it
+takes a virtual SError interrupt exception.
+If KVM advertises this capability, userspace can only specify the ISS field for
+the ESR syndrome. Other parts of the ESR, such as the EC are generated by the
+CPU when the exception is taken. If this virtual SError is taken to EL1 using
+AArch64, this value will be reported in the ISS field of ESR_ELx.
+
+See KVM_CAP_VCPU_EVENTS for more details.
diff --git a/Documentation/virtual/kvm/arm/hyp-abi.txt b/Documentation/virtual/kvm/arm/hyp-abi.txt
new file mode 100644
index 0000000..a20a0be
--- /dev/null
+++ b/Documentation/virtual/kvm/arm/hyp-abi.txt
@@ -0,0 +1,53 @@
+* Internal ABI between the kernel and HYP
+
+This file documents the interaction between the Linux kernel and the
+hypervisor layer when running Linux as a hypervisor (for example
+KVM). It doesn't cover the interaction of the kernel with the
+hypervisor when running as a guest (under Xen, KVM or any other
+hypervisor), or any hypervisor-specific interaction when the kernel is
+used as a host.
+
+On arm and arm64 (without VHE), the kernel doesn't run in hypervisor
+mode, but still needs to interact with it, allowing a built-in
+hypervisor to be either installed or torn down.
+
+In order to achieve this, the kernel must be booted at HYP (arm) or
+EL2 (arm64), allowing it to install a set of stubs before dropping to
+SVC/EL1. These stubs are accessible by using a 'hvc #0' instruction,
+and only act on individual CPUs.
+
+Unless specified otherwise, any built-in hypervisor must implement
+these functions (see arch/arm{,64}/include/asm/virt.h):
+
+* r0/x0 = HVC_SET_VECTORS
+  r1/x1 = vectors
+
+  Set HVBAR/VBAR_EL2 to 'vectors' to enable a hypervisor. 'vectors'
+  must be a physical address, and respect the alignment requirements
+  of the architecture. Only implemented by the initial stubs, not by
+  Linux hypervisors.
+
+* r0/x0 = HVC_RESET_VECTORS
+
+  Turn HYP/EL2 MMU off, and reset HVBAR/VBAR_EL2 to the initials
+  stubs' exception vector value. This effectively disables an existing
+  hypervisor.
+
+* r0/x0 = HVC_SOFT_RESTART
+  r1/x1 = restart address
+  x2 = x0's value when entering the next payload (arm64)
+  x3 = x1's value when entering the next payload (arm64)
+  x4 = x2's value when entering the next payload (arm64)
+
+  Mask all exceptions, disable the MMU, move the arguments into place
+  (arm64 only), and jump to the restart address while at HYP/EL2. This
+  hypercall is not expected to return to its caller.
+
+Any other value of r0/x0 triggers a hypervisor-specific handling,
+which is not documented here.
+
+The return value of a stub hypercall is held by r0/x0, and is 0 on
+success, and HVC_STUB_ERR on error. A stub hypercall is allowed to
+clobber any of the caller-saved registers (x0-x18 on arm64, r0-r3 and
+ip on arm). It is thus recommended to use a function call to perform
+the hypercall.
diff --git a/Documentation/virtual/kvm/arm/psci.txt b/Documentation/virtual/kvm/arm/psci.txt
new file mode 100644
index 0000000..aafdab8
--- /dev/null
+++ b/Documentation/virtual/kvm/arm/psci.txt
@@ -0,0 +1,30 @@
+KVM implements the PSCI (Power State Coordination Interface)
+specification in order to provide services such as CPU on/off, reset
+and power-off to the guest.
+
+The PSCI specification is regularly updated to provide new features,
+and KVM implements these updates if they make sense from a virtualization
+point of view.
+
+This means that a guest booted on two different versions of KVM can
+observe two different "firmware" revisions. This could cause issues if
+a given guest is tied to a particular PSCI revision (unlikely), or if
+a migration causes a different PSCI version to be exposed out of the
+blue to an unsuspecting guest.
+
+In order to remedy this situation, KVM exposes a set of "firmware
+pseudo-registers" that can be manipulated using the GET/SET_ONE_REG
+interface. These registers can be saved/restored by userspace, and set
+to a convenient value if required.
+
+The following register is defined:
+
+* KVM_REG_ARM_PSCI_VERSION:
+
+  - Only valid if the vcpu has the KVM_ARM_VCPU_PSCI_0_2 feature set
+    (and thus has already been initialized)
+  - Returns the current PSCI version on GET_ONE_REG (defaulting to the
+    highest PSCI version implemented by KVM and compatible with v0.2)
+  - Allows any PSCI version implemented by KVM and compatible with
+    v0.2 to be set with SET_ONE_REG
+  - Affects the whole VM (even if the register view is per-vcpu)
diff --git a/Documentation/virtual/kvm/cpuid.txt b/Documentation/virtual/kvm/cpuid.txt
new file mode 100644
index 0000000..97ca194
--- /dev/null
+++ b/Documentation/virtual/kvm/cpuid.txt
@@ -0,0 +1,83 @@
+KVM CPUID bits
+Glauber Costa <glommer@redhat.com>, Red Hat Inc, 2010
+=====================================================
+
+A guest running on a kvm host, can check some of its features using
+cpuid. This is not always guaranteed to work, since userspace can
+mask-out some, or even all KVM-related cpuid features before launching
+a guest.
+
+KVM cpuid functions are:
+
+function: KVM_CPUID_SIGNATURE (0x40000000)
+returns : eax = 0x40000001,
+          ebx = 0x4b4d564b,
+          ecx = 0x564b4d56,
+          edx = 0x4d.
+Note that this value in ebx, ecx and edx corresponds to the string "KVMKVMKVM".
+The value in eax corresponds to the maximum cpuid function present in this leaf,
+and will be updated if more functions are added in the future.
+Note also that old hosts set eax value to 0x0. This should
+be interpreted as if the value was 0x40000001.
+This function queries the presence of KVM cpuid leafs.
+
+
+function: define KVM_CPUID_FEATURES (0x40000001)
+returns : ebx, ecx
+          eax = an OR'ed group of (1 << flag), where each flags is:
+
+
+flag                               || value || meaning
+=============================================================================
+KVM_FEATURE_CLOCKSOURCE            ||     0 || kvmclock available at msrs
+                                   ||       || 0x11 and 0x12.
+------------------------------------------------------------------------------
+KVM_FEATURE_NOP_IO_DELAY           ||     1 || not necessary to perform delays
+                                   ||       || on PIO operations.
+------------------------------------------------------------------------------
+KVM_FEATURE_MMU_OP                 ||     2 || deprecated.
+------------------------------------------------------------------------------
+KVM_FEATURE_CLOCKSOURCE2           ||     3 || kvmclock available at msrs
+                                   ||       || 0x4b564d00 and 0x4b564d01
+------------------------------------------------------------------------------
+KVM_FEATURE_ASYNC_PF               ||     4 || async pf can be enabled by
+                                   ||       || writing to msr 0x4b564d02
+------------------------------------------------------------------------------
+KVM_FEATURE_STEAL_TIME             ||     5 || steal time can be enabled by
+                                   ||       || writing to msr 0x4b564d03.
+------------------------------------------------------------------------------
+KVM_FEATURE_PV_EOI                 ||     6 || paravirtualized end of interrupt
+                                   ||       || handler can be enabled by writing
+                                   ||       || to msr 0x4b564d04.
+------------------------------------------------------------------------------
+KVM_FEATURE_PV_UNHALT              ||     7 || guest checks this feature bit
+                                   ||       || before enabling paravirtualized
+                                   ||       || spinlock support.
+------------------------------------------------------------------------------
+KVM_FEATURE_PV_TLB_FLUSH           ||     9 || guest checks this feature bit
+                                   ||       || before enabling paravirtualized
+                                   ||       || tlb flush.
+------------------------------------------------------------------------------
+KVM_FEATURE_ASYNC_PF_VMEXIT        ||    10 || paravirtualized async PF VM exit
+                                   ||       || can be enabled by setting bit 2
+                                   ||       || when writing to msr 0x4b564d02
+------------------------------------------------------------------------------
+KVM_FEATURE_PV_SEND_IPI            ||    11 || guest checks this feature bit
+                                   ||       || before using paravirtualized
+                                   ||       || send IPIs.
+------------------------------------------------------------------------------
+KVM_FEATURE_CLOCKSOURCE_STABLE_BIT ||    24 || host will warn if no guest-side
+                                   ||       || per-cpu warps are expected in
+                                   ||       || kvmclock.
+------------------------------------------------------------------------------
+
+          edx = an OR'ed group of (1 << flag), where each flags is:
+
+
+flag                               || value || meaning
+==================================================================================
+KVM_HINTS_REALTIME                 ||     0 || guest checks this feature bit to
+                                   ||       || determine that vCPUs are never
+                                   ||       || preempted for an unlimited time,
+                                   ||       || allowing optimizations
+----------------------------------------------------------------------------------
diff --git a/Documentation/virtual/kvm/devices/README b/Documentation/virtual/kvm/devices/README
new file mode 100644
index 0000000..34a6983
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/README
@@ -0,0 +1 @@
+This directory contains specific device bindings for KVM_CAP_DEVICE_CTRL.
diff --git a/Documentation/virtual/kvm/devices/arm-vgic-its.txt b/Documentation/virtual/kvm/devices/arm-vgic-its.txt
new file mode 100644
index 0000000..4f0c9fc
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/arm-vgic-its.txt
@@ -0,0 +1,181 @@
+ARM Virtual Interrupt Translation Service (ITS)
+===============================================
+
+Device types supported:
+  KVM_DEV_TYPE_ARM_VGIC_ITS    ARM Interrupt Translation Service Controller
+
+The ITS allows MSI(-X) interrupts to be injected into guests. This extension is
+optional.  Creating a virtual ITS controller also requires a host GICv3 (see
+arm-vgic-v3.txt), but does not depend on having physical ITS controllers.
+
+There can be multiple ITS controllers per guest, each of them has to have
+a separate, non-overlapping MMIO region.
+
+
+Groups:
+  KVM_DEV_ARM_VGIC_GRP_ADDR
+  Attributes:
+    KVM_VGIC_ITS_ADDR_TYPE (rw, 64-bit)
+      Base address in the guest physical address space of the GICv3 ITS
+      control register frame.
+      This address needs to be 64K aligned and the region covers 128K.
+  Errors:
+    -E2BIG:  Address outside of addressable IPA range
+    -EINVAL: Incorrectly aligned address
+    -EEXIST: Address already configured
+    -EFAULT: Invalid user pointer for attr->addr.
+    -ENODEV: Incorrect attribute or the ITS is not supported.
+
+
+  KVM_DEV_ARM_VGIC_GRP_CTRL
+  Attributes:
+    KVM_DEV_ARM_VGIC_CTRL_INIT
+      request the initialization of the ITS, no additional parameter in
+      kvm_device_attr.addr.
+
+    KVM_DEV_ARM_ITS_CTRL_RESET
+      reset the ITS, no additional parameter in kvm_device_attr.addr.
+      See "ITS Reset State" section.
+
+    KVM_DEV_ARM_ITS_SAVE_TABLES
+      save the ITS table data into guest RAM, at the location provisioned
+      by the guest in corresponding registers/table entries.
+
+      The layout of the tables in guest memory defines an ABI. The entries
+      are laid out in little endian format as described in the last paragraph.
+
+    KVM_DEV_ARM_ITS_RESTORE_TABLES
+      restore the ITS tables from guest RAM to ITS internal structures.
+
+      The GICV3 must be restored before the ITS and all ITS registers but
+      the GITS_CTLR must be restored before restoring the ITS tables.
+
+      The GITS_IIDR read-only register must also be restored before
+      calling KVM_DEV_ARM_ITS_RESTORE_TABLES as the IIDR revision field
+      encodes the ABI revision.
+
+      The expected ordering when restoring the GICv3/ITS is described in section
+      "ITS Restore Sequence".
+
+  Errors:
+    -ENXIO:  ITS not properly configured as required prior to setting
+             this attribute
+    -ENOMEM: Memory shortage when allocating ITS internal data
+    -EINVAL: Inconsistent restored data
+    -EFAULT: Invalid guest ram access
+    -EBUSY:  One or more VCPUS are running
+    -EACCES: The virtual ITS is backed by a physical GICv4 ITS, and the
+	     state is not available
+
+  KVM_DEV_ARM_VGIC_GRP_ITS_REGS
+  Attributes:
+      The attr field of kvm_device_attr encodes the offset of the
+      ITS register, relative to the ITS control frame base address
+      (ITS_base).
+
+      kvm_device_attr.addr points to a __u64 value whatever the width
+      of the addressed register (32/64 bits). 64 bit registers can only
+      be accessed with full length.
+
+      Writes to read-only registers are ignored by the kernel except for:
+      - GITS_CREADR. It must be restored otherwise commands in the queue
+        will be re-executed after restoring CWRITER. GITS_CREADR must be
+        restored before restoring the GITS_CTLR which is likely to enable the
+        ITS. Also it must be restored after GITS_CBASER since a write to
+        GITS_CBASER resets GITS_CREADR.
+      - GITS_IIDR. The Revision field encodes the table layout ABI revision.
+        In the future we might implement direct injection of virtual LPIs.
+        This will require an upgrade of the table layout and an evolution of
+        the ABI. GITS_IIDR must be restored before calling
+        KVM_DEV_ARM_ITS_RESTORE_TABLES.
+
+      For other registers, getting or setting a register has the same
+      effect as reading/writing the register on real hardware.
+  Errors:
+    -ENXIO: Offset does not correspond to any supported register
+    -EFAULT: Invalid user pointer for attr->addr
+    -EINVAL: Offset is not 64-bit aligned
+    -EBUSY: one or more VCPUS are running
+
+ ITS Restore Sequence:
+ -------------------------
+
+The following ordering must be followed when restoring the GIC and the ITS:
+a) restore all guest memory and create vcpus
+b) restore all redistributors
+c) provide the its base address
+   (KVM_DEV_ARM_VGIC_GRP_ADDR)
+d) restore the ITS in the following order:
+   1. Restore GITS_CBASER
+   2. Restore all other GITS_ registers, except GITS_CTLR!
+   3. Load the ITS table data (KVM_DEV_ARM_ITS_RESTORE_TABLES)
+   4. Restore GITS_CTLR
+
+Then vcpus can be started.
+
+ ITS Table ABI REV0:
+ -------------------
+
+ Revision 0 of the ABI only supports the features of a virtual GICv3, and does
+ not support a virtual GICv4 with support for direct injection of virtual
+ interrupts for nested hypervisors.
+
+ The device table and ITT are indexed by the DeviceID and EventID,
+ respectively. The collection table is not indexed by CollectionID, and the
+ entries in the collection are listed in no particular order.
+ All entries are 8 bytes.
+
+ Device Table Entry (DTE):
+
+ bits:     | 63| 62 ... 49 | 48 ... 5 | 4 ... 0 |
+ values:   | V |   next    | ITT_addr |  Size   |
+
+ where;
+ - V indicates whether the entry is valid. If not, other fields
+   are not meaningful.
+ - next: equals to 0 if this entry is the last one; otherwise it
+   corresponds to the DeviceID offset to the next DTE, capped by
+   2^14 -1.
+ - ITT_addr matches bits [51:8] of the ITT address (256 Byte aligned).
+ - Size specifies the supported number of bits for the EventID,
+   minus one
+
+ Collection Table Entry (CTE):
+
+ bits:     | 63| 62 ..  52  | 51 ... 16 | 15  ...   0 |
+ values:   | V |    RES0    |  RDBase   |    ICID     |
+
+ where:
+ - V indicates whether the entry is valid. If not, other fields are
+   not meaningful.
+ - RES0: reserved field with Should-Be-Zero-or-Preserved behavior.
+ - RDBase is the PE number (GICR_TYPER.Processor_Number semantic),
+ - ICID is the collection ID
+
+ Interrupt Translation Entry (ITE):
+
+ bits:     | 63 ... 48 | 47 ... 16 | 15 ... 0 |
+ values:   |    next   |   pINTID  |  ICID    |
+
+ where:
+ - next: equals to 0 if this entry is the last one; otherwise it corresponds
+   to the EventID offset to the next ITE capped by 2^16 -1.
+ - pINTID is the physical LPI ID; if zero, it means the entry is not valid
+   and other fields are not meaningful.
+ - ICID is the collection ID
+
+ ITS Reset State:
+ ----------------
+
+RESET returns the ITS to the same state that it was when first created and
+initialized. When the RESET command returns, the following things are
+guaranteed:
+
+- The ITS is not enabled and quiescent
+  GITS_CTLR.Enabled = 0 .Quiescent=1
+- There is no internally cached state
+- No collection or device table are used
+  GITS_BASER<n>.Valid = 0
+- GITS_CBASER = 0, GITS_CREADR = 0, GITS_CWRITER = 0
+- The ABI version is unchanged and remains the one set when the ITS
+  device was first created.
diff --git a/Documentation/virtual/kvm/devices/arm-vgic-v3.txt b/Documentation/virtual/kvm/devices/arm-vgic-v3.txt
new file mode 100644
index 0000000..ff290b4
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/arm-vgic-v3.txt
@@ -0,0 +1,251 @@
+ARM Virtual Generic Interrupt Controller v3 and later (VGICv3)
+==============================================================
+
+
+Device types supported:
+  KVM_DEV_TYPE_ARM_VGIC_V3     ARM Generic Interrupt Controller v3.0
+
+Only one VGIC instance may be instantiated through this API.  The created VGIC
+will act as the VM interrupt controller, requiring emulated user-space devices
+to inject interrupts to the VGIC instead of directly to CPUs.  It is not
+possible to create both a GICv3 and GICv2 on the same VM.
+
+Creating a guest GICv3 device requires a host GICv3 as well.
+
+
+Groups:
+  KVM_DEV_ARM_VGIC_GRP_ADDR
+  Attributes:
+    KVM_VGIC_V3_ADDR_TYPE_DIST (rw, 64-bit)
+      Base address in the guest physical address space of the GICv3 distributor
+      register mappings. Only valid for KVM_DEV_TYPE_ARM_VGIC_V3.
+      This address needs to be 64K aligned and the region covers 64 KByte.
+
+    KVM_VGIC_V3_ADDR_TYPE_REDIST (rw, 64-bit)
+      Base address in the guest physical address space of the GICv3
+      redistributor register mappings. There are two 64K pages for each
+      VCPU and all of the redistributor pages are contiguous.
+      Only valid for KVM_DEV_TYPE_ARM_VGIC_V3.
+      This address needs to be 64K aligned.
+
+    KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION (rw, 64-bit)
+      The attribute data pointed to by kvm_device_attr.addr is a __u64 value:
+      bits:     | 63   ....  52  |  51   ....   16 | 15 - 12  |11 - 0
+      values:   |     count      |       base      |  flags   | index
+      - index encodes the unique redistributor region index
+      - flags: reserved for future use, currently 0
+      - base field encodes bits [51:16] of the guest physical base address
+        of the first redistributor in the region.
+      - count encodes the number of redistributors in the region. Must be
+        greater than 0.
+      There are two 64K pages for each redistributor in the region and
+      redistributors are laid out contiguously within the region. Regions
+      are filled with redistributors in the index order. The sum of all
+      region count fields must be greater than or equal to the number of
+      VCPUs. Redistributor regions must be registered in the incremental
+      index order, starting from index 0.
+      The characteristics of a specific redistributor region can be read
+      by presetting the index field in the attr data.
+      Only valid for KVM_DEV_TYPE_ARM_VGIC_V3.
+
+  It is invalid to mix calls with KVM_VGIC_V3_ADDR_TYPE_REDIST and
+  KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION attributes.
+
+  Errors:
+    -E2BIG:  Address outside of addressable IPA range
+    -EINVAL: Incorrectly aligned address, bad redistributor region
+             count/index, mixed redistributor region attribute usage
+    -EEXIST: Address already configured
+    -ENOENT: Attempt to read the characteristics of a non existing
+             redistributor region
+    -ENXIO:  The group or attribute is unknown/unsupported for this device
+             or hardware support is missing.
+    -EFAULT: Invalid user pointer for attr->addr.
+
+
+  KVM_DEV_ARM_VGIC_GRP_DIST_REGS
+  KVM_DEV_ARM_VGIC_GRP_REDIST_REGS
+  Attributes:
+    The attr field of kvm_device_attr encodes two values:
+    bits:     | 63   ....  32  |  31   ....    0 |
+    values:   |      mpidr     |      offset     |
+
+    All distributor regs are (rw, 32-bit) and kvm_device_attr.addr points to a
+    __u32 value.  64-bit registers must be accessed by separately accessing the
+    lower and higher word.
+
+    Writes to read-only registers are ignored by the kernel.
+
+    KVM_DEV_ARM_VGIC_GRP_DIST_REGS accesses the main distributor registers.
+    KVM_DEV_ARM_VGIC_GRP_REDIST_REGS accesses the redistributor of the CPU
+    specified by the mpidr.
+
+    The offset is relative to the "[Re]Distributor base address" as defined
+    in the GICv3/4 specs.  Getting or setting such a register has the same
+    effect as reading or writing the register on real hardware, except for the
+    following registers: GICD_STATUSR, GICR_STATUSR, GICD_ISPENDR,
+    GICR_ISPENDR0, GICD_ICPENDR, and GICR_ICPENDR0.  These registers behave
+    differently when accessed via this interface compared to their
+    architecturally defined behavior to allow software a full view of the
+    VGIC's internal state.
+
+    The mpidr field is used to specify which
+    redistributor is accessed.  The mpidr is ignored for the distributor.
+
+    The mpidr encoding is based on the affinity information in the
+    architecture defined MPIDR, and the field is encoded as follows:
+      | 63 .... 56 | 55 .... 48 | 47 .... 40 | 39 .... 32 |
+      |    Aff3    |    Aff2    |    Aff1    |    Aff0    |
+
+    Note that distributor fields are not banked, but return the same value
+    regardless of the mpidr used to access the register.
+
+    GICD_IIDR.Revision is updated when the KVM implementation is changed in a
+    way directly observable by the guest or userspace.  Userspace should read
+    GICD_IIDR from KVM and write back the read value to confirm its expected
+    behavior is aligned with the KVM implementation.  Userspace should set
+    GICD_IIDR before setting any other registers to ensure the expected
+    behavior.
+
+
+    The GICD_STATUSR and GICR_STATUSR registers are architecturally defined such
+    that a write of a clear bit has no effect, whereas a write with a set bit
+    clears that value.  To allow userspace to freely set the values of these two
+    registers, setting the attributes with the register offsets for these two
+    registers simply sets the non-reserved bits to the value written.
+
+
+    Accesses (reads and writes) to the GICD_ISPENDR register region and
+    GICR_ISPENDR0 registers get/set the value of the latched pending state for
+    the interrupts.
+
+    This is identical to the value returned by a guest read from ISPENDR for an
+    edge triggered interrupt, but may differ for level triggered interrupts.
+    For edge triggered interrupts, once an interrupt becomes pending (whether
+    because of an edge detected on the input line or because of a guest write
+    to ISPENDR) this state is "latched", and only cleared when either the
+    interrupt is activated or when the guest writes to ICPENDR. A level
+    triggered interrupt may be pending either because the level input is held
+    high by a device, or because of a guest write to the ISPENDR register. Only
+    ISPENDR writes are latched; if the device lowers the line level then the
+    interrupt is no longer pending unless the guest also wrote to ISPENDR, and
+    conversely writes to ICPENDR or activations of the interrupt do not clear
+    the pending status if the line level is still being held high.  (These
+    rules are documented in the GICv3 specification descriptions of the ICPENDR
+    and ISPENDR registers.) For a level triggered interrupt the value accessed
+    here is that of the latch which is set by ISPENDR and cleared by ICPENDR or
+    interrupt activation, whereas the value returned by a guest read from
+    ISPENDR is the logical OR of the latch value and the input line level.
+
+    Raw access to the latch state is provided to userspace so that it can save
+    and restore the entire GIC internal state (which is defined by the
+    combination of the current input line level and the latch state, and cannot
+    be deduced from purely the line level and the value of the ISPENDR
+    registers).
+
+    Accesses to GICD_ICPENDR register region and GICR_ICPENDR0 registers have
+    RAZ/WI semantics, meaning that reads always return 0 and writes are always
+    ignored.
+
+  Errors:
+    -ENXIO: Getting or setting this register is not yet supported
+    -EBUSY: One or more VCPUs are running
+
+
+  KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS
+  Attributes:
+    The attr field of kvm_device_attr encodes two values:
+    bits:     | 63      ....       32 | 31  ....  16 | 15  ....  0 |
+    values:   |         mpidr         |      RES     |    instr    |
+
+    The mpidr field encodes the CPU ID based on the affinity information in the
+    architecture defined MPIDR, and the field is encoded as follows:
+      | 63 .... 56 | 55 .... 48 | 47 .... 40 | 39 .... 32 |
+      |    Aff3    |    Aff2    |    Aff1    |    Aff0    |
+
+    The instr field encodes the system register to access based on the fields
+    defined in the A64 instruction set encoding for system register access
+    (RES means the bits are reserved for future use and should be zero):
+
+      | 15 ... 14 | 13 ... 11 | 10 ... 7 | 6 ... 3 | 2 ... 0 |
+      |   Op 0    |    Op1    |    CRn   |   CRm   |   Op2   |
+
+    All system regs accessed through this API are (rw, 64-bit) and
+    kvm_device_attr.addr points to a __u64 value.
+
+    KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS accesses the CPU interface registers for the
+    CPU specified by the mpidr field.
+
+    CPU interface registers access is not implemented for AArch32 mode.
+    Error -ENXIO is returned when accessed in AArch32 mode.
+  Errors:
+    -ENXIO: Getting or setting this register is not yet supported
+    -EBUSY: VCPU is running
+    -EINVAL: Invalid mpidr or register value supplied
+
+
+  KVM_DEV_ARM_VGIC_GRP_NR_IRQS
+  Attributes:
+    A value describing the number of interrupts (SGI, PPI and SPI) for
+    this GIC instance, ranging from 64 to 1024, in increments of 32.
+
+    kvm_device_attr.addr points to a __u32 value.
+
+  Errors:
+    -EINVAL: Value set is out of the expected range
+    -EBUSY: Value has already be set.
+
+
+  KVM_DEV_ARM_VGIC_GRP_CTRL
+  Attributes:
+    KVM_DEV_ARM_VGIC_CTRL_INIT
+      request the initialization of the VGIC, no additional parameter in
+      kvm_device_attr.addr.
+    KVM_DEV_ARM_VGIC_SAVE_PENDING_TABLES
+      save all LPI pending bits into guest RAM pending tables.
+
+      The first kB of the pending table is not altered by this operation.
+  Errors:
+    -ENXIO: VGIC not properly configured as required prior to calling
+     this attribute
+    -ENODEV: no online VCPU
+    -ENOMEM: memory shortage when allocating vgic internal data
+    -EFAULT: Invalid guest ram access
+    -EBUSY:  One or more VCPUS are running
+
+
+  KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO
+  Attributes:
+    The attr field of kvm_device_attr encodes the following values:
+    bits:     | 63      ....       32 | 31   ....    10 | 9  ....  0 |
+    values:   |         mpidr         |      info       |   vINTID   |
+
+    The vINTID specifies which set of IRQs is reported on.
+
+    The info field specifies which information userspace wants to get or set
+    using this interface.  Currently we support the following info values:
+
+      VGIC_LEVEL_INFO_LINE_LEVEL:
+	Get/Set the input level of the IRQ line for a set of 32 contiguously
+	numbered interrupts.
+	vINTID must be a multiple of 32.
+
+	kvm_device_attr.addr points to a __u32 value which will contain a
+	bitmap where a set bit means the interrupt level is asserted.
+
+	Bit[n] indicates the status for interrupt vINTID + n.
+
+    SGIs and any interrupt with a higher ID than the number of interrupts
+    supported, will be RAZ/WI.  LPIs are always edge-triggered and are
+    therefore not supported by this interface.
+
+    PPIs are reported per VCPU as specified in the mpidr field, and SPIs are
+    reported with the same value regardless of the mpidr specified.
+
+    The mpidr field encodes the CPU ID based on the affinity information in the
+    architecture defined MPIDR, and the field is encoded as follows:
+      | 63 .... 56 | 55 .... 48 | 47 .... 40 | 39 .... 32 |
+      |    Aff3    |    Aff2    |    Aff1    |    Aff0    |
+  Errors:
+    -EINVAL: vINTID is not multiple of 32 or
+     info field is not VGIC_LEVEL_INFO_LINE_LEVEL
diff --git a/Documentation/virtual/kvm/devices/arm-vgic.txt b/Documentation/virtual/kvm/devices/arm-vgic.txt
new file mode 100644
index 0000000..97b6518
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/arm-vgic.txt
@@ -0,0 +1,127 @@
+ARM Virtual Generic Interrupt Controller v2 (VGIC)
+==================================================
+
+Device types supported:
+  KVM_DEV_TYPE_ARM_VGIC_V2     ARM Generic Interrupt Controller v2.0
+
+Only one VGIC instance may be instantiated through either this API or the
+legacy KVM_CREATE_IRQCHIP API.  The created VGIC will act as the VM interrupt
+controller, requiring emulated user-space devices to inject interrupts to the
+VGIC instead of directly to CPUs.
+
+GICv3 implementations with hardware compatibility support allow creating a
+guest GICv2 through this interface.  For information on creating a guest GICv3
+device and guest ITS devices, see arm-vgic-v3.txt.  It is not possible to
+create both a GICv3 and GICv2 device on the same VM.
+
+
+Groups:
+  KVM_DEV_ARM_VGIC_GRP_ADDR
+  Attributes:
+    KVM_VGIC_V2_ADDR_TYPE_DIST (rw, 64-bit)
+      Base address in the guest physical address space of the GIC distributor
+      register mappings. Only valid for KVM_DEV_TYPE_ARM_VGIC_V2.
+      This address needs to be 4K aligned and the region covers 4 KByte.
+
+    KVM_VGIC_V2_ADDR_TYPE_CPU (rw, 64-bit)
+      Base address in the guest physical address space of the GIC virtual cpu
+      interface register mappings. Only valid for KVM_DEV_TYPE_ARM_VGIC_V2.
+      This address needs to be 4K aligned and the region covers 4 KByte.
+  Errors:
+    -E2BIG:  Address outside of addressable IPA range
+    -EINVAL: Incorrectly aligned address
+    -EEXIST: Address already configured
+    -ENXIO:  The group or attribute is unknown/unsupported for this device
+             or hardware support is missing.
+    -EFAULT: Invalid user pointer for attr->addr.
+
+  KVM_DEV_ARM_VGIC_GRP_DIST_REGS
+  Attributes:
+    The attr field of kvm_device_attr encodes two values:
+    bits:     | 63   ....  40 | 39 ..  32  |  31   ....    0 |
+    values:   |    reserved   | vcpu_index |      offset     |
+
+    All distributor regs are (rw, 32-bit)
+
+    The offset is relative to the "Distributor base address" as defined in the
+    GICv2 specs.  Getting or setting such a register has the same effect as
+    reading or writing the register on the actual hardware from the cpu whose
+    index is specified with the vcpu_index field.  Note that most distributor
+    fields are not banked, but return the same value regardless of the
+    vcpu_index used to access the register.
+
+    GICD_IIDR.Revision is updated when the KVM implementation of an emulated
+    GICv2 is changed in a way directly observable by the guest or userspace.
+    Userspace should read GICD_IIDR from KVM and write back the read value to
+    confirm its expected behavior is aligned with the KVM implementation.
+    Userspace should set GICD_IIDR before setting any other registers (both
+    KVM_DEV_ARM_VGIC_GRP_DIST_REGS and KVM_DEV_ARM_VGIC_GRP_CPU_REGS) to ensure
+    the expected behavior. Unless GICD_IIDR has been set from userspace, writes
+    to the interrupt group registers (GICD_IGROUPR) are ignored.
+  Errors:
+    -ENXIO: Getting or setting this register is not yet supported
+    -EBUSY: One or more VCPUs are running
+    -EINVAL: Invalid vcpu_index supplied
+
+  KVM_DEV_ARM_VGIC_GRP_CPU_REGS
+  Attributes:
+    The attr field of kvm_device_attr encodes two values:
+    bits:     | 63   ....  40 | 39 ..  32  |  31   ....    0 |
+    values:   |    reserved   | vcpu_index |      offset     |
+
+    All CPU interface regs are (rw, 32-bit)
+
+    The offset specifies the offset from the "CPU interface base address" as
+    defined in the GICv2 specs.  Getting or setting such a register has the
+    same effect as reading or writing the register on the actual hardware.
+
+    The Active Priorities Registers APRn are implementation defined, so we set a
+    fixed format for our implementation that fits with the model of a "GICv2
+    implementation without the security extensions" which we present to the
+    guest.  This interface always exposes four register APR[0-3] describing the
+    maximum possible 128 preemption levels.  The semantics of the register
+    indicate if any interrupts in a given preemption level are in the active
+    state by setting the corresponding bit.
+
+    Thus, preemption level X has one or more active interrupts if and only if:
+
+      APRn[X mod 32] == 0b1,  where n = X / 32
+
+    Bits for undefined preemption levels are RAZ/WI.
+
+    Note that this differs from a CPU's view of the APRs on hardware in which
+    a GIC without the security extensions expose group 0 and group 1 active
+    priorities in separate register groups, whereas we show a combined view
+    similar to GICv2's GICH_APR.
+
+    For historical reasons and to provide ABI compatibility with userspace we
+    export the GICC_PMR register in the format of the GICH_VMCR.VMPriMask
+    field in the lower 5 bits of a word, meaning that userspace must always
+    use the lower 5 bits to communicate with the KVM device and must shift the
+    value left by 3 places to obtain the actual priority mask level.
+
+  Errors:
+    -ENXIO: Getting or setting this register is not yet supported
+    -EBUSY: One or more VCPUs are running
+    -EINVAL: Invalid vcpu_index supplied
+
+  KVM_DEV_ARM_VGIC_GRP_NR_IRQS
+  Attributes:
+    A value describing the number of interrupts (SGI, PPI and SPI) for
+    this GIC instance, ranging from 64 to 1024, in increments of 32.
+
+  Errors:
+    -EINVAL: Value set is out of the expected range
+    -EBUSY: Value has already be set, or GIC has already been initialized
+            with default values.
+
+  KVM_DEV_ARM_VGIC_GRP_CTRL
+  Attributes:
+    KVM_DEV_ARM_VGIC_CTRL_INIT
+      request the initialization of the VGIC or ITS, no additional parameter
+      in kvm_device_attr.addr.
+  Errors:
+    -ENXIO: VGIC not properly configured as required prior to calling
+     this attribute
+    -ENODEV: no online VCPU
+    -ENOMEM: memory shortage when allocating vgic internal data
diff --git a/Documentation/virtual/kvm/devices/mpic.txt b/Documentation/virtual/kvm/devices/mpic.txt
new file mode 100644
index 0000000..8257397
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/mpic.txt
@@ -0,0 +1,53 @@
+MPIC interrupt controller
+=========================
+
+Device types supported:
+  KVM_DEV_TYPE_FSL_MPIC_20     Freescale MPIC v2.0
+  KVM_DEV_TYPE_FSL_MPIC_42     Freescale MPIC v4.2
+
+Only one MPIC instance, of any type, may be instantiated.  The created
+MPIC will act as the system interrupt controller, connecting to each
+vcpu's interrupt inputs.
+
+Groups:
+  KVM_DEV_MPIC_GRP_MISC
+  Attributes:
+    KVM_DEV_MPIC_BASE_ADDR (rw, 64-bit)
+      Base address of the 256 KiB MPIC register space.  Must be
+      naturally aligned.  A value of zero disables the mapping.
+      Reset value is zero.
+
+  KVM_DEV_MPIC_GRP_REGISTER (rw, 32-bit)
+    Access an MPIC register, as if the access were made from the guest.
+    "attr" is the byte offset into the MPIC register space.  Accesses
+    must be 4-byte aligned.
+
+    MSIs may be signaled by using this attribute group to write
+    to the relevant MSIIR.
+
+  KVM_DEV_MPIC_GRP_IRQ_ACTIVE (rw, 32-bit)
+    IRQ input line for each standard openpic source.  0 is inactive and 1
+    is active, regardless of interrupt sense.
+
+    For edge-triggered interrupts:  Writing 1 is considered an activating
+    edge, and writing 0 is ignored.  Reading returns 1 if a previously
+    signaled edge has not been acknowledged, and 0 otherwise.
+
+    "attr" is the IRQ number.  IRQ numbers for standard sources are the
+    byte offset of the relevant IVPR from EIVPR0, divided by 32.
+
+IRQ Routing:
+
+  The MPIC emulation supports IRQ routing. Only a single MPIC device can
+  be instantiated. Once that device has been created, it's available as
+  irqchip id 0.
+
+  This irqchip 0 has 256 interrupt pins, which expose the interrupts in
+  the main array of interrupt sources (a.k.a. "SRC" interrupts).
+
+  The numbering is the same as the MPIC device tree binding -- based on
+  the register offset from the beginning of the sources array, without
+  regard to any subdivisions in chip documentation such as "internal"
+  or "external" interrupts.
+
+  Access to non-SRC interrupts is not implemented through IRQ routing mechanisms.
diff --git a/Documentation/virtual/kvm/devices/s390_flic.txt b/Documentation/virtual/kvm/devices/s390_flic.txt
new file mode 100644
index 0000000..a4e20a0
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/s390_flic.txt
@@ -0,0 +1,163 @@
+FLIC (floating interrupt controller)
+====================================
+
+FLIC handles floating (non per-cpu) interrupts, i.e. I/O, service and some
+machine check interruptions. All interrupts are stored in a per-vm list of
+pending interrupts. FLIC performs operations on this list.
+
+Only one FLIC instance may be instantiated.
+
+FLIC provides support to
+- add interrupts (KVM_DEV_FLIC_ENQUEUE)
+- inspect currently pending interrupts (KVM_FLIC_GET_ALL_IRQS)
+- purge all pending floating interrupts (KVM_DEV_FLIC_CLEAR_IRQS)
+- purge one pending floating I/O interrupt (KVM_DEV_FLIC_CLEAR_IO_IRQ)
+- enable/disable for the guest transparent async page faults
+- register and modify adapter interrupt sources (KVM_DEV_FLIC_ADAPTER_*)
+- modify AIS (adapter-interruption-suppression) mode state (KVM_DEV_FLIC_AISM)
+- inject adapter interrupts on a specified adapter (KVM_DEV_FLIC_AIRQ_INJECT)
+- get/set all AIS mode states (KVM_DEV_FLIC_AISM_ALL)
+
+Groups:
+  KVM_DEV_FLIC_ENQUEUE
+    Passes a buffer and length into the kernel which are then injected into
+    the list of pending interrupts.
+    attr->addr contains the pointer to the buffer and attr->attr contains
+    the length of the buffer.
+    The format of the data structure kvm_s390_irq as it is copied from userspace
+    is defined in usr/include/linux/kvm.h.
+
+  KVM_DEV_FLIC_GET_ALL_IRQS
+    Copies all floating interrupts into a buffer provided by userspace.
+    When the buffer is too small it returns -ENOMEM, which is the indication
+    for userspace to try again with a bigger buffer.
+    -ENOBUFS is returned when the allocation of a kernelspace buffer has
+    failed.
+    -EFAULT is returned when copying data to userspace failed.
+    All interrupts remain pending, i.e. are not deleted from the list of
+    currently pending interrupts.
+    attr->addr contains the userspace address of the buffer into which all
+    interrupt data will be copied.
+    attr->attr contains the size of the buffer in bytes.
+
+  KVM_DEV_FLIC_CLEAR_IRQS
+    Simply deletes all elements from the list of currently pending floating
+    interrupts.  No interrupts are injected into the guest.
+
+  KVM_DEV_FLIC_CLEAR_IO_IRQ
+    Deletes one (if any) I/O interrupt for a subchannel identified by the
+    subsystem identification word passed via the buffer specified by
+    attr->addr (address) and attr->attr (length).
+
+  KVM_DEV_FLIC_APF_ENABLE
+    Enables async page faults for the guest. So in case of a major page fault
+    the host is allowed to handle this async and continues the guest.
+
+  KVM_DEV_FLIC_APF_DISABLE_WAIT
+    Disables async page faults for the guest and waits until already pending
+    async page faults are done. This is necessary to trigger a completion interrupt
+    for every init interrupt before migrating the interrupt list.
+
+  KVM_DEV_FLIC_ADAPTER_REGISTER
+    Register an I/O adapter interrupt source. Takes a kvm_s390_io_adapter
+    describing the adapter to register:
+
+struct kvm_s390_io_adapter {
+	__u32 id;
+	__u8 isc;
+	__u8 maskable;
+	__u8 swap;
+	__u8 flags;
+};
+
+   id contains the unique id for the adapter, isc the I/O interruption subclass
+   to use, maskable whether this adapter may be masked (interrupts turned off),
+   swap whether the indicators need to be byte swapped, and flags contains
+   further characteristics of the adapter.
+   Currently defined values for 'flags' are:
+   - KVM_S390_ADAPTER_SUPPRESSIBLE: adapter is subject to AIS
+     (adapter-interrupt-suppression) facility. This flag only has an effect if
+     the AIS capability is enabled.
+   Unknown flag values are ignored.
+
+
+  KVM_DEV_FLIC_ADAPTER_MODIFY
+    Modifies attributes of an existing I/O adapter interrupt source. Takes
+    a kvm_s390_io_adapter_req specifying the adapter and the operation:
+
+struct kvm_s390_io_adapter_req {
+	__u32 id;
+	__u8 type;
+	__u8 mask;
+	__u16 pad0;
+	__u64 addr;
+};
+
+    id specifies the adapter and type the operation. The supported operations
+    are:
+
+    KVM_S390_IO_ADAPTER_MASK
+      mask or unmask the adapter, as specified in mask
+
+    KVM_S390_IO_ADAPTER_MAP
+      perform a gmap translation for the guest address provided in addr,
+      pin a userspace page for the translated address and add it to the
+      list of mappings
+      Note: A new mapping will be created unconditionally; therefore,
+            the calling code should avoid making duplicate mappings.
+
+    KVM_S390_IO_ADAPTER_UNMAP
+      release a userspace page for the translated address specified in addr
+      from the list of mappings
+
+  KVM_DEV_FLIC_AISM
+    modify the adapter-interruption-suppression mode for a given isc if the
+    AIS capability is enabled. Takes a kvm_s390_ais_req describing:
+
+struct kvm_s390_ais_req {
+	__u8 isc;
+	__u16 mode;
+};
+
+    isc contains the target I/O interruption subclass, mode the target
+    adapter-interruption-suppression mode. The following modes are
+    currently supported:
+    - KVM_S390_AIS_MODE_ALL: ALL-Interruptions Mode, i.e. airq injection
+      is always allowed;
+    - KVM_S390_AIS_MODE_SINGLE: SINGLE-Interruption Mode, i.e. airq
+      injection is only allowed once and the following adapter interrupts
+      will be suppressed until the mode is set again to ALL-Interruptions
+      or SINGLE-Interruption mode.
+
+  KVM_DEV_FLIC_AIRQ_INJECT
+    Inject adapter interrupts on a specified adapter.
+    attr->attr contains the unique id for the adapter, which allows for
+    adapter-specific checks and actions.
+    For adapters subject to AIS, handle the airq injection suppression for
+    an isc according to the adapter-interruption-suppression mode on condition
+    that the AIS capability is enabled.
+
+  KVM_DEV_FLIC_AISM_ALL
+    Gets or sets the adapter-interruption-suppression mode for all ISCs. Takes
+    a kvm_s390_ais_all describing:
+
+struct kvm_s390_ais_all {
+       __u8 simm; /* Single-Interruption-Mode mask */
+       __u8 nimm; /* No-Interruption-Mode mask *
+};
+
+    simm contains Single-Interruption-Mode mask for all ISCs, nimm contains
+    No-Interruption-Mode mask for all ISCs. Each bit in simm and nimm corresponds
+    to an ISC (MSB0 bit 0 to ISC 0 and so on). The combination of simm bit and
+    nimm bit presents AIS mode for a ISC.
+
+    KVM_DEV_FLIC_AISM_ALL is indicated by KVM_CAP_S390_AIS_MIGRATION.
+
+Note: The KVM_SET_DEVICE_ATTR/KVM_GET_DEVICE_ATTR device ioctls executed on
+FLIC with an unknown group or attribute gives the error code EINVAL (instead of
+ENXIO, as specified in the API documentation). It is not possible to conclude
+that a FLIC operation is unavailable based on the error code resulting from a
+usage attempt.
+
+Note: The KVM_DEV_FLIC_CLEAR_IO_IRQ ioctl will return EINVAL in case a zero
+schid is specified.
diff --git a/Documentation/virtual/kvm/devices/vcpu.txt b/Documentation/virtual/kvm/devices/vcpu.txt
new file mode 100644
index 0000000..2b5dab1
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/vcpu.txt
@@ -0,0 +1,62 @@
+Generic vcpu interface
+====================================
+
+The virtual cpu "device" also accepts the ioctls KVM_SET_DEVICE_ATTR,
+KVM_GET_DEVICE_ATTR, and KVM_HAS_DEVICE_ATTR. The interface uses the same struct
+kvm_device_attr as other devices, but targets VCPU-wide settings and controls.
+
+The groups and attributes per virtual cpu, if any, are architecture specific.
+
+1. GROUP: KVM_ARM_VCPU_PMU_V3_CTRL
+Architectures: ARM64
+
+1.1. ATTRIBUTE: KVM_ARM_VCPU_PMU_V3_IRQ
+Parameters: in kvm_device_attr.addr the address for PMU overflow interrupt is a
+            pointer to an int
+Returns: -EBUSY: The PMU overflow interrupt is already set
+         -ENXIO: The overflow interrupt not set when attempting to get it
+         -ENODEV: PMUv3 not supported
+         -EINVAL: Invalid PMU overflow interrupt number supplied or
+                  trying to set the IRQ number without using an in-kernel
+                  irqchip.
+
+A value describing the PMUv3 (Performance Monitor Unit v3) overflow interrupt
+number for this vcpu. This interrupt could be a PPI or SPI, but the interrupt
+type must be same for each vcpu. As a PPI, the interrupt number is the same for
+all vcpus, while as an SPI it must be a separate number per vcpu.
+
+1.2 ATTRIBUTE: KVM_ARM_VCPU_PMU_V3_INIT
+Parameters: no additional parameter in kvm_device_attr.addr
+Returns: -ENODEV: PMUv3 not supported or GIC not initialized
+         -ENXIO: PMUv3 not properly configured or in-kernel irqchip not
+                 configured as required prior to calling this attribute
+         -EBUSY: PMUv3 already initialized
+
+Request the initialization of the PMUv3.  If using the PMUv3 with an in-kernel
+virtual GIC implementation, this must be done after initializing the in-kernel
+irqchip.
+
+
+2. GROUP: KVM_ARM_VCPU_TIMER_CTRL
+Architectures: ARM,ARM64
+
+2.1. ATTRIBUTE: KVM_ARM_VCPU_TIMER_IRQ_VTIMER
+2.2. ATTRIBUTE: KVM_ARM_VCPU_TIMER_IRQ_PTIMER
+Parameters: in kvm_device_attr.addr the address for the timer interrupt is a
+            pointer to an int
+Returns: -EINVAL: Invalid timer interrupt number
+         -EBUSY:  One or more VCPUs has already run
+
+A value describing the architected timer interrupt number when connected to an
+in-kernel virtual GIC.  These must be a PPI (16 <= intid < 32).  Setting the
+attribute overrides the default values (see below).
+
+KVM_ARM_VCPU_TIMER_IRQ_VTIMER: The EL1 virtual timer intid (default: 27)
+KVM_ARM_VCPU_TIMER_IRQ_PTIMER: The EL1 physical timer intid (default: 30)
+
+Setting the same PPI for different timers will prevent the VCPUs from running.
+Setting the interrupt number on a VCPU configures all VCPUs created at that
+time to use the number provided for a given timer, overwriting any previously
+configured values on other VCPUs.  Userspace should configure the interrupt
+numbers on at least one VCPU after creating all VCPUs and before running any
+VCPUs.
diff --git a/Documentation/virtual/kvm/devices/vfio.txt b/Documentation/virtual/kvm/devices/vfio.txt
new file mode 100644
index 0000000..528c77c
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/vfio.txt
@@ -0,0 +1,36 @@
+VFIO virtual device
+===================
+
+Device types supported:
+  KVM_DEV_TYPE_VFIO
+
+Only one VFIO instance may be created per VM.  The created device
+tracks VFIO groups in use by the VM and features of those groups
+important to the correctness and acceleration of the VM.  As groups
+are enabled and disabled for use by the VM, KVM should be updated
+about their presence.  When registered with KVM, a reference to the
+VFIO-group is held by KVM.
+
+Groups:
+  KVM_DEV_VFIO_GROUP
+
+KVM_DEV_VFIO_GROUP attributes:
+  KVM_DEV_VFIO_GROUP_ADD: Add a VFIO group to VFIO-KVM device tracking
+	kvm_device_attr.addr points to an int32_t file descriptor
+	for the VFIO group.
+  KVM_DEV_VFIO_GROUP_DEL: Remove a VFIO group from VFIO-KVM device tracking
+	kvm_device_attr.addr points to an int32_t file descriptor
+	for the VFIO group.
+  KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE: attaches a guest visible TCE table
+	allocated by sPAPR KVM.
+	kvm_device_attr.addr points to a struct:
+
+	struct kvm_vfio_spapr_tce {
+		__s32	groupfd;
+		__s32	tablefd;
+	};
+
+	where
+	@groupfd is a file descriptor for a VFIO group;
+	@tablefd is a file descriptor for a TCE table allocated via
+		KVM_CREATE_SPAPR_TCE.
diff --git a/Documentation/virtual/kvm/devices/vm.txt b/Documentation/virtual/kvm/devices/vm.txt
new file mode 100644
index 0000000..95ca68d
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/vm.txt
@@ -0,0 +1,269 @@
+Generic vm interface
+====================================
+
+The virtual machine "device" also accepts the ioctls KVM_SET_DEVICE_ATTR,
+KVM_GET_DEVICE_ATTR, and KVM_HAS_DEVICE_ATTR. The interface uses the same
+struct kvm_device_attr as other devices, but targets VM-wide settings
+and controls.
+
+The groups and attributes per virtual machine, if any, are architecture
+specific.
+
+1. GROUP: KVM_S390_VM_MEM_CTRL
+Architectures: s390
+
+1.1. ATTRIBUTE: KVM_S390_VM_MEM_ENABLE_CMMA
+Parameters: none
+Returns: -EBUSY if a vcpu is already defined, otherwise 0
+
+Enables Collaborative Memory Management Assist (CMMA) for the virtual machine.
+
+1.2. ATTRIBUTE: KVM_S390_VM_MEM_CLR_CMMA
+Parameters: none
+Returns: -EINVAL if CMMA was not enabled
+         0 otherwise
+
+Clear the CMMA status for all guest pages, so any pages the guest marked
+as unused are again used any may not be reclaimed by the host.
+
+1.3. ATTRIBUTE KVM_S390_VM_MEM_LIMIT_SIZE
+Parameters: in attr->addr the address for the new limit of guest memory
+Returns: -EFAULT if the given address is not accessible
+         -EINVAL if the virtual machine is of type UCONTROL
+         -E2BIG if the given guest memory is to big for that machine
+         -EBUSY if a vcpu is already defined
+         -ENOMEM if not enough memory is available for a new shadow guest mapping
+          0 otherwise
+
+Allows userspace to query the actual limit and set a new limit for
+the maximum guest memory size. The limit will be rounded up to
+2048 MB, 4096 GB, 8192 TB respectively, as this limit is governed by
+the number of page table levels. In the case that there is no limit we will set
+the limit to KVM_S390_NO_MEM_LIMIT (U64_MAX).
+
+2. GROUP: KVM_S390_VM_CPU_MODEL
+Architectures: s390
+
+2.1. ATTRIBUTE: KVM_S390_VM_CPU_MACHINE (r/o)
+
+Allows user space to retrieve machine and kvm specific cpu related information:
+
+struct kvm_s390_vm_cpu_machine {
+       __u64 cpuid;           # CPUID of host
+       __u32 ibc;             # IBC level range offered by host
+       __u8  pad[4];
+       __u64 fac_mask[256];   # set of cpu facilities enabled by KVM
+       __u64 fac_list[256];   # set of cpu facilities offered by host
+}
+
+Parameters: address of buffer to store the machine related cpu data
+            of type struct kvm_s390_vm_cpu_machine*
+Returns:    -EFAULT if the given address is not accessible from kernel space
+	    -ENOMEM if not enough memory is available to process the ioctl
+	    0 in case of success
+
+2.2. ATTRIBUTE: KVM_S390_VM_CPU_PROCESSOR (r/w)
+
+Allows user space to retrieve or request to change cpu related information for a vcpu:
+
+struct kvm_s390_vm_cpu_processor {
+       __u64 cpuid;           # CPUID currently (to be) used by this vcpu
+       __u16 ibc;             # IBC level currently (to be) used by this vcpu
+       __u8  pad[6];
+       __u64 fac_list[256];   # set of cpu facilities currently (to be) used
+                              # by this vcpu
+}
+
+KVM does not enforce or limit the cpu model data in any form. Take the information
+retrieved by means of KVM_S390_VM_CPU_MACHINE as hint for reasonable configuration
+setups. Instruction interceptions triggered by additionally set facility bits that
+are not handled by KVM need to by imlemented in the VM driver code.
+
+Parameters: address of buffer to store/set the processor related cpu
+	    data of type struct kvm_s390_vm_cpu_processor*.
+Returns:    -EBUSY in case 1 or more vcpus are already activated (only in write case)
+	    -EFAULT if the given address is not accessible from kernel space
+	    -ENOMEM if not enough memory is available to process the ioctl
+	    0 in case of success
+
+2.3. ATTRIBUTE: KVM_S390_VM_CPU_MACHINE_FEAT (r/o)
+
+Allows user space to retrieve available cpu features. A feature is available if
+provided by the hardware and supported by kvm. In theory, cpu features could
+even be completely emulated by kvm.
+
+struct kvm_s390_vm_cpu_feat {
+        __u64 feat[16]; # Bitmap (1 = feature available), MSB 0 bit numbering
+};
+
+Parameters: address of a buffer to load the feature list from.
+Returns:    -EFAULT if the given address is not accessible from kernel space.
+	    0 in case of success.
+
+2.4. ATTRIBUTE: KVM_S390_VM_CPU_PROCESSOR_FEAT (r/w)
+
+Allows user space to retrieve or change enabled cpu features for all VCPUs of a
+VM. Features that are not available cannot be enabled.
+
+See 2.3. for a description of the parameter struct.
+
+Parameters: address of a buffer to store/load the feature list from.
+Returns:    -EFAULT if the given address is not accessible from kernel space.
+	    -EINVAL if a cpu feature that is not available is to be enabled.
+	    -EBUSY if at least one VCPU has already been defined.
+	    0 in case of success.
+
+2.5. ATTRIBUTE: KVM_S390_VM_CPU_MACHINE_SUBFUNC (r/o)
+
+Allows user space to retrieve available cpu subfunctions without any filtering
+done by a set IBC. These subfunctions are indicated to the guest VCPU via
+query or "test bit" subfunctions and used e.g. by cpacf functions, plo and ptff.
+
+A subfunction block is only valid if KVM_S390_VM_CPU_MACHINE contains the
+STFL(E) bit introducing the affected instruction. If the affected instruction
+indicates subfunctions via a "query subfunction", the response block is
+contained in the returned struct. If the affected instruction
+indicates subfunctions via a "test bit" mechanism, the subfunction codes are
+contained in the returned struct in MSB 0 bit numbering.
+
+struct kvm_s390_vm_cpu_subfunc {
+       u8 plo[32];           # always valid (ESA/390 feature)
+       u8 ptff[16];          # valid with TOD-clock steering
+       u8 kmac[16];          # valid with Message-Security-Assist
+       u8 kmc[16];           # valid with Message-Security-Assist
+       u8 km[16];            # valid with Message-Security-Assist
+       u8 kimd[16];          # valid with Message-Security-Assist
+       u8 klmd[16];          # valid with Message-Security-Assist
+       u8 pckmo[16];         # valid with Message-Security-Assist-Extension 3
+       u8 kmctr[16];         # valid with Message-Security-Assist-Extension 4
+       u8 kmf[16];           # valid with Message-Security-Assist-Extension 4
+       u8 kmo[16];           # valid with Message-Security-Assist-Extension 4
+       u8 pcc[16];           # valid with Message-Security-Assist-Extension 4
+       u8 ppno[16];          # valid with Message-Security-Assist-Extension 5
+       u8 kma[16];           # valid with Message-Security-Assist-Extension 8
+       u8 reserved[1808];    # reserved for future instructions
+};
+
+Parameters: address of a buffer to load the subfunction blocks from.
+Returns:    -EFAULT if the given address is not accessible from kernel space.
+	    0 in case of success.
+
+2.6. ATTRIBUTE: KVM_S390_VM_CPU_PROCESSOR_SUBFUNC (r/w)
+
+Allows user space to retrieve or change cpu subfunctions to be indicated for
+all VCPUs of a VM. This attribute will only be available if kernel and
+hardware support are in place.
+
+The kernel uses the configured subfunction blocks for indication to
+the guest. A subfunction block will only be used if the associated STFL(E) bit
+has not been disabled by user space (so the instruction to be queried is
+actually available for the guest).
+
+As long as no data has been written, a read will fail. The IBC will be used
+to determine available subfunctions in this case, this will guarantee backward
+compatibility.
+
+See 2.5. for a description of the parameter struct.
+
+Parameters: address of a buffer to store/load the subfunction blocks from.
+Returns:    -EFAULT if the given address is not accessible from kernel space.
+	    -EINVAL when reading, if there was no write yet.
+	    -EBUSY if at least one VCPU has already been defined.
+	    0 in case of success.
+
+3. GROUP: KVM_S390_VM_TOD
+Architectures: s390
+
+3.1. ATTRIBUTE: KVM_S390_VM_TOD_HIGH
+
+Allows user space to set/get the TOD clock extension (u8) (superseded by
+KVM_S390_VM_TOD_EXT).
+
+Parameters: address of a buffer in user space to store the data (u8) to
+Returns:    -EFAULT if the given address is not accessible from kernel space
+	    -EINVAL if setting the TOD clock extension to != 0 is not supported
+
+3.2. ATTRIBUTE: KVM_S390_VM_TOD_LOW
+
+Allows user space to set/get bits 0-63 of the TOD clock register as defined in
+the POP (u64).
+
+Parameters: address of a buffer in user space to store the data (u64) to
+Returns:    -EFAULT if the given address is not accessible from kernel space
+
+3.3. ATTRIBUTE: KVM_S390_VM_TOD_EXT
+Allows user space to set/get bits 0-63 of the TOD clock register as defined in
+the POP (u64). If the guest CPU model supports the TOD clock extension (u8), it
+also allows user space to get/set it. If the guest CPU model does not support
+it, it is stored as 0 and not allowed to be set to a value != 0.
+
+Parameters: address of a buffer in user space to store the data
+            (kvm_s390_vm_tod_clock) to
+Returns:    -EFAULT if the given address is not accessible from kernel space
+	    -EINVAL if setting the TOD clock extension to != 0 is not supported
+
+4. GROUP: KVM_S390_VM_CRYPTO
+Architectures: s390
+
+4.1. ATTRIBUTE: KVM_S390_VM_CRYPTO_ENABLE_AES_KW (w/o)
+
+Allows user space to enable aes key wrapping, including generating a new
+wrapping key.
+
+Parameters: none
+Returns:    0
+
+4.2. ATTRIBUTE: KVM_S390_VM_CRYPTO_ENABLE_DEA_KW (w/o)
+
+Allows user space to enable dea key wrapping, including generating a new
+wrapping key.
+
+Parameters: none
+Returns:    0
+
+4.3. ATTRIBUTE: KVM_S390_VM_CRYPTO_DISABLE_AES_KW (w/o)
+
+Allows user space to disable aes key wrapping, clearing the wrapping key.
+
+Parameters: none
+Returns:    0
+
+4.4. ATTRIBUTE: KVM_S390_VM_CRYPTO_DISABLE_DEA_KW (w/o)
+
+Allows user space to disable dea key wrapping, clearing the wrapping key.
+
+Parameters: none
+Returns:    0
+
+5. GROUP: KVM_S390_VM_MIGRATION
+Architectures: s390
+
+5.1. ATTRIBUTE: KVM_S390_VM_MIGRATION_STOP (w/o)
+
+Allows userspace to stop migration mode, needed for PGSTE migration.
+Setting this attribute when migration mode is not active will have no
+effects.
+
+Parameters: none
+Returns:    0
+
+5.2. ATTRIBUTE: KVM_S390_VM_MIGRATION_START (w/o)
+
+Allows userspace to start migration mode, needed for PGSTE migration.
+Setting this attribute when migration mode is already active will have
+no effects.
+
+Parameters: none
+Returns:    -ENOMEM if there is not enough free memory to start migration mode
+	    -EINVAL if the state of the VM is invalid (e.g. no memory defined)
+	    0 in case of success.
+
+5.3. ATTRIBUTE: KVM_S390_VM_MIGRATION_STATUS (r/o)
+
+Allows userspace to query the status of migration mode.
+
+Parameters: address of a buffer in user space to store the data (u64) to;
+	    the data itself is either 0 if migration mode is disabled or 1
+	    if it is enabled
+Returns:    -EFAULT if the given address is not accessible from kernel space
+	    0 in case of success.
diff --git a/Documentation/virtual/kvm/devices/xics.txt b/Documentation/virtual/kvm/devices/xics.txt
new file mode 100644
index 0000000..4286493
--- /dev/null
+++ b/Documentation/virtual/kvm/devices/xics.txt
@@ -0,0 +1,66 @@
+XICS interrupt controller
+
+Device type supported: KVM_DEV_TYPE_XICS
+
+Groups:
+  KVM_DEV_XICS_SOURCES
+  Attributes: One per interrupt source, indexed by the source number.
+
+This device emulates the XICS (eXternal Interrupt Controller
+Specification) defined in PAPR.  The XICS has a set of interrupt
+sources, each identified by a 20-bit source number, and a set of
+Interrupt Control Presentation (ICP) entities, also called "servers",
+each associated with a virtual CPU.
+
+The ICP entities are created by enabling the KVM_CAP_IRQ_ARCH
+capability for each vcpu, specifying KVM_CAP_IRQ_XICS in args[0] and
+the interrupt server number (i.e. the vcpu number from the XICS's
+point of view) in args[1] of the kvm_enable_cap struct.  Each ICP has
+64 bits of state which can be read and written using the
+KVM_GET_ONE_REG and KVM_SET_ONE_REG ioctls on the vcpu.  The 64 bit
+state word has the following bitfields, starting at the
+least-significant end of the word:
+
+* Unused, 16 bits
+
+* Pending interrupt priority, 8 bits
+  Zero is the highest priority, 255 means no interrupt is pending.
+
+* Pending IPI (inter-processor interrupt) priority, 8 bits
+  Zero is the highest priority, 255 means no IPI is pending.
+
+* Pending interrupt source number, 24 bits
+  Zero means no interrupt pending, 2 means an IPI is pending
+
+* Current processor priority, 8 bits
+  Zero is the highest priority, meaning no interrupts can be
+  delivered, and 255 is the lowest priority.
+
+Each source has 64 bits of state that can be read and written using
+the KVM_GET_DEVICE_ATTR and KVM_SET_DEVICE_ATTR ioctls, specifying the
+KVM_DEV_XICS_SOURCES attribute group, with the attribute number being
+the interrupt source number.  The 64 bit state word has the following
+bitfields, starting from the least-significant end of the word:
+
+* Destination (server number), 32 bits
+  This specifies where the interrupt should be sent, and is the
+  interrupt server number specified for the destination vcpu.
+
+* Priority, 8 bits
+  This is the priority specified for this interrupt source, where 0 is
+  the highest priority and 255 is the lowest.  An interrupt with a
+  priority of 255 will never be delivered.
+
+* Level sensitive flag, 1 bit
+  This bit is 1 for a level-sensitive interrupt source, or 0 for
+  edge-sensitive (or MSI).
+
+* Masked flag, 1 bit
+  This bit is set to 1 if the interrupt is masked (cannot be delivered
+  regardless of its priority), for example by the ibm,int-off RTAS
+  call, or 0 if it is not masked.
+
+* Pending flag, 1 bit
+  This bit is 1 if the source has a pending interrupt, otherwise 0.
+
+Only one XICS instance may be created per VM.
diff --git a/Documentation/virtual/kvm/halt-polling.txt b/Documentation/virtual/kvm/halt-polling.txt
new file mode 100644
index 0000000..4a84183
--- /dev/null
+++ b/Documentation/virtual/kvm/halt-polling.txt
@@ -0,0 +1,127 @@
+The KVM halt polling system
+===========================
+
+The KVM halt polling system provides a feature within KVM whereby the latency
+of a guest can, under some circumstances, be reduced by polling in the host
+for some time period after the guest has elected to no longer run by cedeing.
+That is, when a guest vcpu has ceded, or in the case of powerpc when all of the
+vcpus of a single vcore have ceded, the host kernel polls for wakeup conditions
+before giving up the cpu to the scheduler in order to let something else run.
+
+Polling provides a latency advantage in cases where the guest can be run again
+very quickly by at least saving us a trip through the scheduler, normally on
+the order of a few micro-seconds, although performance benefits are workload
+dependant. In the event that no wakeup source arrives during the polling
+interval or some other task on the runqueue is runnable the scheduler is
+invoked. Thus halt polling is especially useful on workloads with very short
+wakeup periods where the time spent halt polling is minimised and the time
+savings of not invoking the scheduler are distinguishable.
+
+The generic halt polling code is implemented in:
+
+	virt/kvm/kvm_main.c: kvm_vcpu_block()
+
+The powerpc kvm-hv specific case is implemented in:
+
+	arch/powerpc/kvm/book3s_hv.c: kvmppc_vcore_blocked()
+
+Halt Polling Interval
+=====================
+
+The maximum time for which to poll before invoking the scheduler, referred to
+as the halt polling interval, is increased and decreased based on the perceived
+effectiveness of the polling in an attempt to limit pointless polling.
+This value is stored in either the vcpu struct:
+
+	kvm_vcpu->halt_poll_ns
+
+or in the case of powerpc kvm-hv, in the vcore struct:
+
+	kvmppc_vcore->halt_poll_ns
+
+Thus this is a per vcpu (or vcore) value.
+
+During polling if a wakeup source is received within the halt polling interval,
+the interval is left unchanged. In the event that a wakeup source isn't
+received during the polling interval (and thus schedule is invoked) there are
+two options, either the polling interval and total block time[0] were less than
+the global max polling interval (see module params below), or the total block
+time was greater than the global max polling interval.
+
+In the event that both the polling interval and total block time were less than
+the global max polling interval then the polling interval can be increased in
+the hope that next time during the longer polling interval the wake up source
+will be received while the host is polling and the latency benefits will be
+received. The polling interval is grown in the function grow_halt_poll_ns() and
+is multiplied by the module parameter halt_poll_ns_grow.
+
+In the event that the total block time was greater than the global max polling
+interval then the host will never poll for long enough (limited by the global
+max) to wakeup during the polling interval so it may as well be shrunk in order
+to avoid pointless polling. The polling interval is shrunk in the function
+shrink_halt_poll_ns() and is divided by the module parameter
+halt_poll_ns_shrink, or set to 0 iff halt_poll_ns_shrink == 0.
+
+It is worth noting that this adjustment process attempts to hone in on some
+steady state polling interval but will only really do a good job for wakeups
+which come at an approximately constant rate, otherwise there will be constant
+adjustment of the polling interval.
+
+[0] total block time: the time between when the halt polling function is
+		      invoked and a wakeup source received (irrespective of
+		      whether the scheduler is invoked within that function).
+
+Module Parameters
+=================
+
+The kvm module has 3 tuneable module parameters to adjust the global max
+polling interval as well as the rate at which the polling interval is grown and
+shrunk. These variables are defined in include/linux/kvm_host.h and as module
+parameters in virt/kvm/kvm_main.c, or arch/powerpc/kvm/book3s_hv.c in the
+powerpc kvm-hv case.
+
+Module Parameter    |	     Description	      |	     Default Value
+--------------------------------------------------------------------------------
+halt_poll_ns	    | The global max polling interval | KVM_HALT_POLL_NS_DEFAULT
+		    | which defines the ceiling value |
+		    | of the polling interval for     | (per arch value)
+		    | each vcpu. 		      |
+--------------------------------------------------------------------------------
+halt_poll_ns_grow   | The value by which the halt     |	2
+		    | polling interval is multiplied  |
+		    | in the grow_halt_poll_ns()      |
+		    | function.			      |
+--------------------------------------------------------------------------------
+halt_poll_ns_shrink | The value by which the halt     |	0
+		    | polling interval is divided in  |
+		    | the shrink_halt_poll_ns()	      |
+		    | function.			      |
+--------------------------------------------------------------------------------
+
+These module parameters can be set from the debugfs files in:
+
+	/sys/module/kvm/parameters/
+
+Note: that these module parameters are system wide values and are not able to
+      be tuned on a per vm basis.
+
+Further Notes
+=============
+
+- Care should be taken when setting the halt_poll_ns module parameter as a
+large value has the potential to drive the cpu usage to 100% on a machine which
+would be almost entirely idle otherwise. This is because even if a guest has
+wakeups during which very little work is done and which are quite far apart, if
+the period is shorter than the global max polling interval (halt_poll_ns) then
+the host will always poll for the entire block time and thus cpu utilisation
+will go to 100%.
+
+- Halt polling essentially presents a trade off between power usage and latency
+and the module parameters should be used to tune the affinity for this. Idle
+cpu time is essentially converted to host kernel time with the aim of decreasing
+latency when entering the guest.
+
+- Halt polling will only be conducted by the host when no other tasks are
+runnable on that cpu, otherwise the polling will cease immediately and
+schedule will be invoked to allow that other task to run. Thus this doesn't
+allow a guest to denial of service the cpu.
diff --git a/Documentation/virtual/kvm/hypercalls.txt b/Documentation/virtual/kvm/hypercalls.txt
new file mode 100644
index 0000000..da24c13
--- /dev/null
+++ b/Documentation/virtual/kvm/hypercalls.txt
@@ -0,0 +1,143 @@
+Linux KVM Hypercall:
+===================
+X86:
+ KVM Hypercalls have a three-byte sequence of either the vmcall or the vmmcall
+ instruction. The hypervisor can replace it with instructions that are
+ guaranteed to be supported.
+
+ Up to four arguments may be passed in rbx, rcx, rdx, and rsi respectively.
+ The hypercall number should be placed in rax and the return value will be
+ placed in rax.  No other registers will be clobbered unless explicitly stated
+ by the particular hypercall.
+
+S390:
+  R2-R7 are used for parameters 1-6. In addition, R1 is used for hypercall
+  number. The return value is written to R2.
+
+  S390 uses diagnose instruction as hypercall (0x500) along with hypercall
+  number in R1.
+
+  For further information on the S390 diagnose call as supported by KVM,
+  refer to Documentation/virtual/kvm/s390-diag.txt.
+
+ PowerPC:
+  It uses R3-R10 and hypercall number in R11. R4-R11 are used as output registers.
+  Return value is placed in R3.
+
+  KVM hypercalls uses 4 byte opcode, that are patched with 'hypercall-instructions'
+  property inside the device tree's /hypervisor node.
+  For more information refer to Documentation/virtual/kvm/ppc-pv.txt
+
+MIPS:
+  KVM hypercalls use the HYPCALL instruction with code 0 and the hypercall
+  number in $2 (v0). Up to four arguments may be placed in $4-$7 (a0-a3) and
+  the return value is placed in $2 (v0).
+
+KVM Hypercalls Documentation
+===========================
+The template for each hypercall is:
+1. Hypercall name.
+2. Architecture(s)
+3. Status (deprecated, obsolete, active)
+4. Purpose
+
+1. KVM_HC_VAPIC_POLL_IRQ
+------------------------
+Architecture: x86
+Status: active
+Purpose: Trigger guest exit so that the host can check for pending
+interrupts on reentry.
+
+2. KVM_HC_MMU_OP
+------------------------
+Architecture: x86
+Status: deprecated.
+Purpose: Support MMU operations such as writing to PTE,
+flushing TLB, release PT.
+
+3. KVM_HC_FEATURES
+------------------------
+Architecture: PPC
+Status: active
+Purpose: Expose hypercall availability to the guest. On x86 platforms, cpuid
+used to enumerate which hypercalls are available. On PPC, either device tree
+based lookup ( which is also what EPAPR dictates) OR KVM specific enumeration
+mechanism (which is this hypercall) can be used.
+
+4. KVM_HC_PPC_MAP_MAGIC_PAGE
+------------------------
+Architecture: PPC
+Status: active
+Purpose: To enable communication between the hypervisor and guest there is a
+shared page that contains parts of supervisor visible register state.
+The guest can map this shared page to access its supervisor register through
+memory using this hypercall.
+
+5. KVM_HC_KICK_CPU
+------------------------
+Architecture: x86
+Status: active
+Purpose: Hypercall used to wakeup a vcpu from HLT state
+Usage example : A vcpu of a paravirtualized guest that is busywaiting in guest
+kernel mode for an event to occur (ex: a spinlock to become available) can
+execute HLT instruction once it has busy-waited for more than a threshold
+time-interval. Execution of HLT instruction would cause the hypervisor to put
+the vcpu to sleep until occurrence of an appropriate event. Another vcpu of the
+same guest can wakeup the sleeping vcpu by issuing KVM_HC_KICK_CPU hypercall,
+specifying APIC ID (a1) of the vcpu to be woken up. An additional argument (a0)
+is used in the hypercall for future use.
+
+
+6. KVM_HC_CLOCK_PAIRING
+------------------------
+Architecture: x86
+Status: active
+Purpose: Hypercall used to synchronize host and guest clocks.
+Usage:
+
+a0: guest physical address where host copies
+"struct kvm_clock_offset" structure.
+
+a1: clock_type, ATM only KVM_CLOCK_PAIRING_WALLCLOCK (0)
+is supported (corresponding to the host's CLOCK_REALTIME clock).
+
+		struct kvm_clock_pairing {
+			__s64 sec;
+			__s64 nsec;
+			__u64 tsc;
+			__u32 flags;
+			__u32 pad[9];
+		};
+
+       Where:
+               * sec: seconds from clock_type clock.
+               * nsec: nanoseconds from clock_type clock.
+               * tsc: guest TSC value used to calculate sec/nsec pair
+               * flags: flags, unused (0) at the moment.
+
+The hypercall lets a guest compute a precise timestamp across
+host and guest.  The guest can use the returned TSC value to
+compute the CLOCK_REALTIME for its clock, at the same instant.
+
+Returns KVM_EOPNOTSUPP if the host does not use TSC clocksource,
+or if clock type is different than KVM_CLOCK_PAIRING_WALLCLOCK.
+
+6. KVM_HC_SEND_IPI
+------------------------
+Architecture: x86
+Status: active
+Purpose: Send IPIs to multiple vCPUs.
+
+a0: lower part of the bitmap of destination APIC IDs
+a1: higher part of the bitmap of destination APIC IDs
+a2: the lowest APIC ID in bitmap
+a3: APIC ICR
+
+The hypercall lets a guest send multicast IPIs, with at most 128
+128 destinations per hypercall in 64-bit mode and 64 vCPUs per
+hypercall in 32-bit mode.  The destinations are represented by a
+bitmap contained in the first two arguments (a0 and a1). Bit 0 of
+a0 corresponds to the APIC ID in the third argument (a2), bit 1
+corresponds to the APIC ID a2+1, and so on.
+
+Returns the number of CPUs to which the IPIs were delivered successfully.
diff --git a/Documentation/virtual/kvm/locking.txt b/Documentation/virtual/kvm/locking.txt
new file mode 100644
index 0000000..1bb8bca
--- /dev/null
+++ b/Documentation/virtual/kvm/locking.txt
@@ -0,0 +1,217 @@
+KVM Lock Overview
+=================
+
+1. Acquisition Orders
+---------------------
+
+The acquisition orders for mutexes are as follows:
+
+- kvm->lock is taken outside vcpu->mutex
+
+- kvm->lock is taken outside kvm->slots_lock and kvm->irq_lock
+
+- kvm->slots_lock is taken outside kvm->irq_lock, though acquiring
+  them together is quite rare.
+
+On x86, vcpu->mutex is taken outside kvm->arch.hyperv.hv_lock.
+
+For spinlocks, kvm_lock is taken outside kvm->mmu_lock.
+
+Everything else is a leaf: no other lock is taken inside the critical
+sections.
+
+2: Exception
+------------
+
+Fast page fault:
+
+Fast page fault is the fast path which fixes the guest page fault out of
+the mmu-lock on x86. Currently, the page fault can be fast in one of the
+following two cases:
+
+1. Access Tracking: The SPTE is not present, but it is marked for access
+tracking i.e. the SPTE_SPECIAL_MASK is set. That means we need to
+restore the saved R/X bits. This is described in more detail later below.
+
+2. Write-Protection: The SPTE is present and the fault is
+caused by write-protect. That means we just need to change the W bit of the 
+spte.
+
+What we use to avoid all the race is the SPTE_HOST_WRITEABLE bit and
+SPTE_MMU_WRITEABLE bit on the spte:
+- SPTE_HOST_WRITEABLE means the gfn is writable on host.
+- SPTE_MMU_WRITEABLE means the gfn is writable on mmu. The bit is set when
+  the gfn is writable on guest mmu and it is not write-protected by shadow
+  page write-protection.
+
+On fast page fault path, we will use cmpxchg to atomically set the spte W
+bit if spte.SPTE_HOST_WRITEABLE = 1 and spte.SPTE_WRITE_PROTECT = 1, or 
+restore the saved R/X bits if VMX_EPT_TRACK_ACCESS mask is set, or both. This
+is safe because whenever changing these bits can be detected by cmpxchg.
+
+But we need carefully check these cases:
+1): The mapping from gfn to pfn
+The mapping from gfn to pfn may be changed since we can only ensure the pfn
+is not changed during cmpxchg. This is a ABA problem, for example, below case
+will happen:
+
+At the beginning:
+gpte = gfn1
+gfn1 is mapped to pfn1 on host
+spte is the shadow page table entry corresponding with gpte and
+spte = pfn1
+
+   VCPU 0                           VCPU0
+on fast page fault path:
+
+   old_spte = *spte;
+                                 pfn1 is swapped out:
+                                    spte = 0;
+
+                                 pfn1 is re-alloced for gfn2.
+
+                                 gpte is changed to point to
+                                 gfn2 by the guest:
+                                    spte = pfn1;
+
+   if (cmpxchg(spte, old_spte, old_spte+W)
+	mark_page_dirty(vcpu->kvm, gfn1)
+             OOPS!!!
+
+We dirty-log for gfn1, that means gfn2 is lost in dirty-bitmap.
+
+For direct sp, we can easily avoid it since the spte of direct sp is fixed
+to gfn. For indirect sp, before we do cmpxchg, we call gfn_to_pfn_atomic()
+to pin gfn to pfn, because after gfn_to_pfn_atomic():
+- We have held the refcount of pfn that means the pfn can not be freed and
+  be reused for another gfn.
+- The pfn is writable that means it can not be shared between different gfns
+  by KSM.
+
+Then, we can ensure the dirty bitmaps is correctly set for a gfn.
+
+Currently, to simplify the whole things, we disable fast page fault for
+indirect shadow page.
+
+2): Dirty bit tracking
+In the origin code, the spte can be fast updated (non-atomically) if the
+spte is read-only and the Accessed bit has already been set since the
+Accessed bit and Dirty bit can not be lost.
+
+But it is not true after fast page fault since the spte can be marked
+writable between reading spte and updating spte. Like below case:
+
+At the beginning:
+spte.W = 0
+spte.Accessed = 1
+
+   VCPU 0                                       VCPU0
+In mmu_spte_clear_track_bits():
+
+   old_spte = *spte;
+
+   /* 'if' condition is satisfied. */
+   if (old_spte.Accessed == 1 &&
+        old_spte.W == 0)
+      spte = 0ull;
+                                         on fast page fault path:
+                                             spte.W = 1
+                                         memory write on the spte:
+                                             spte.Dirty = 1
+
+
+   else
+      old_spte = xchg(spte, 0ull)
+
+
+   if (old_spte.Accessed == 1)
+      kvm_set_pfn_accessed(spte.pfn);
+   if (old_spte.Dirty == 1)
+      kvm_set_pfn_dirty(spte.pfn);
+      OOPS!!!
+
+The Dirty bit is lost in this case.
+
+In order to avoid this kind of issue, we always treat the spte as "volatile"
+if it can be updated out of mmu-lock, see spte_has_volatile_bits(), it means,
+the spte is always atomically updated in this case.
+
+3): flush tlbs due to spte updated
+If the spte is updated from writable to readonly, we should flush all TLBs,
+otherwise rmap_write_protect will find a read-only spte, even though the
+writable spte might be cached on a CPU's TLB.
+
+As mentioned before, the spte can be updated to writable out of mmu-lock on
+fast page fault path, in order to easily audit the path, we see if TLBs need
+be flushed caused by this reason in mmu_spte_update() since this is a common
+function to update spte (present -> present).
+
+Since the spte is "volatile" if it can be updated out of mmu-lock, we always
+atomically update the spte, the race caused by fast page fault can be avoided,
+See the comments in spte_has_volatile_bits() and mmu_spte_update().
+
+Lockless Access Tracking:
+
+This is used for Intel CPUs that are using EPT but do not support the EPT A/D
+bits. In this case, when the KVM MMU notifier is called to track accesses to a
+page (via kvm_mmu_notifier_clear_flush_young), it marks the PTE as not-present
+by clearing the RWX bits in the PTE and storing the original R & X bits in
+some unused/ignored bits. In addition, the SPTE_SPECIAL_MASK is also set on the
+PTE (using the ignored bit 62). When the VM tries to access the page later on,
+a fault is generated and the fast page fault mechanism described above is used
+to atomically restore the PTE to a Present state. The W bit is not saved when
+the PTE is marked for access tracking and during restoration to the Present
+state, the W bit is set depending on whether or not it was a write access. If
+it wasn't, then the W bit will remain clear until a write access happens, at 
+which time it will be set using the Dirty tracking mechanism described above.
+
+3. Reference
+------------
+
+Name:		kvm_lock
+Type:		spinlock_t
+Arch:		any
+Protects:	- vm_list
+
+Name:		kvm_count_lock
+Type:		raw_spinlock_t
+Arch:		any
+Protects:	- hardware virtualization enable/disable
+Comment:	'raw' because hardware enabling/disabling must be atomic /wrt
+		migration.
+
+Name:		kvm_arch::tsc_write_lock
+Type:		raw_spinlock
+Arch:		x86
+Protects:	- kvm_arch::{last_tsc_write,last_tsc_nsec,last_tsc_offset}
+		- tsc offset in vmcb
+Comment:	'raw' because updating the tsc offsets must not be preempted.
+
+Name:		kvm->mmu_lock
+Type:		spinlock_t
+Arch:		any
+Protects:	-shadow page/shadow tlb entry
+Comment:	it is a spinlock since it is used in mmu notifier.
+
+Name:		kvm->srcu
+Type:		srcu lock
+Arch:		any
+Protects:	- kvm->memslots
+		- kvm->buses
+Comment:	The srcu read lock must be held while accessing memslots (e.g.
+		when using gfn_to_* functions) and while accessing in-kernel
+		MMIO/PIO address->device structure mapping (kvm->buses).
+		The srcu index can be stored in kvm_vcpu->srcu_idx per vcpu
+		if it is needed by multiple functions.
+
+Name:		blocked_vcpu_on_cpu_lock
+Type:		spinlock_t
+Arch:		x86
+Protects:	blocked_vcpu_on_cpu
+Comment:	This is a per-CPU lock and it is used for VT-d posted-interrupts.
+		When VT-d posted-interrupts is supported and the VM has assigned
+		devices, we put the blocked vCPU on the list blocked_vcpu_on_cpu
+		protected by blocked_vcpu_on_cpu_lock, when VT-d hardware issues
+		wakeup notification event since external interrupts from the
+		assigned devices happens, we will find the vCPU on the list to
+		wakeup.
diff --git a/Documentation/virtual/kvm/mmu.txt b/Documentation/virtual/kvm/mmu.txt
new file mode 100644
index 0000000..e507a9e
--- /dev/null
+++ b/Documentation/virtual/kvm/mmu.txt
@@ -0,0 +1,469 @@
+The x86 kvm shadow mmu
+======================
+
+The mmu (in arch/x86/kvm, files mmu.[ch] and paging_tmpl.h) is responsible
+for presenting a standard x86 mmu to the guest, while translating guest
+physical addresses to host physical addresses.
+
+The mmu code attempts to satisfy the following requirements:
+
+- correctness: the guest should not be able to determine that it is running
+               on an emulated mmu except for timing (we attempt to comply
+               with the specification, not emulate the characteristics of
+               a particular implementation such as tlb size)
+- security:    the guest must not be able to touch host memory not assigned
+               to it
+- performance: minimize the performance penalty imposed by the mmu
+- scaling:     need to scale to large memory and large vcpu guests
+- hardware:    support the full range of x86 virtualization hardware
+- integration: Linux memory management code must be in control of guest memory
+               so that swapping, page migration, page merging, transparent
+               hugepages, and similar features work without change
+- dirty tracking: report writes to guest memory to enable live migration
+               and framebuffer-based displays
+- footprint:   keep the amount of pinned kernel memory low (most memory
+               should be shrinkable)
+- reliability:  avoid multipage or GFP_ATOMIC allocations
+
+Acronyms
+========
+
+pfn   host page frame number
+hpa   host physical address
+hva   host virtual address
+gfn   guest frame number
+gpa   guest physical address
+gva   guest virtual address
+ngpa  nested guest physical address
+ngva  nested guest virtual address
+pte   page table entry (used also to refer generically to paging structure
+      entries)
+gpte  guest pte (referring to gfns)
+spte  shadow pte (referring to pfns)
+tdp   two dimensional paging (vendor neutral term for NPT and EPT)
+
+Virtual and real hardware supported
+===================================
+
+The mmu supports first-generation mmu hardware, which allows an atomic switch
+of the current paging mode and cr3 during guest entry, as well as
+two-dimensional paging (AMD's NPT and Intel's EPT).  The emulated hardware
+it exposes is the traditional 2/3/4 level x86 mmu, with support for global
+pages, pae, pse, pse36, cr0.wp, and 1GB pages. Emulated hardware also
+able to expose NPT capable hardware on NPT capable hosts.
+
+Translation
+===========
+
+The primary job of the mmu is to program the processor's mmu to translate
+addresses for the guest.  Different translations are required at different
+times:
+
+- when guest paging is disabled, we translate guest physical addresses to
+  host physical addresses (gpa->hpa)
+- when guest paging is enabled, we translate guest virtual addresses, to
+  guest physical addresses, to host physical addresses (gva->gpa->hpa)
+- when the guest launches a guest of its own, we translate nested guest
+  virtual addresses, to nested guest physical addresses, to guest physical
+  addresses, to host physical addresses (ngva->ngpa->gpa->hpa)
+
+The primary challenge is to encode between 1 and 3 translations into hardware
+that support only 1 (traditional) and 2 (tdp) translations.  When the
+number of required translations matches the hardware, the mmu operates in
+direct mode; otherwise it operates in shadow mode (see below).
+
+Memory
+======
+
+Guest memory (gpa) is part of the user address space of the process that is
+using kvm.  Userspace defines the translation between guest addresses and user
+addresses (gpa->hva); note that two gpas may alias to the same hva, but not
+vice versa.
+
+These hvas may be backed using any method available to the host: anonymous
+memory, file backed memory, and device memory.  Memory might be paged by the
+host at any time.
+
+Events
+======
+
+The mmu is driven by events, some from the guest, some from the host.
+
+Guest generated events:
+- writes to control registers (especially cr3)
+- invlpg/invlpga instruction execution
+- access to missing or protected translations
+
+Host generated events:
+- changes in the gpa->hpa translation (either through gpa->hva changes or
+  through hva->hpa changes)
+- memory pressure (the shrinker)
+
+Shadow pages
+============
+
+The principal data structure is the shadow page, 'struct kvm_mmu_page'.  A
+shadow page contains 512 sptes, which can be either leaf or nonleaf sptes.  A
+shadow page may contain a mix of leaf and nonleaf sptes.
+
+A nonleaf spte allows the hardware mmu to reach the leaf pages and
+is not related to a translation directly.  It points to other shadow pages.
+
+A leaf spte corresponds to either one or two translations encoded into
+one paging structure entry.  These are always the lowest level of the
+translation stack, with optional higher level translations left to NPT/EPT.
+Leaf ptes point at guest pages.
+
+The following table shows translations encoded by leaf ptes, with higher-level
+translations in parentheses:
+
+ Non-nested guests:
+  nonpaging:     gpa->hpa
+  paging:        gva->gpa->hpa
+  paging, tdp:   (gva->)gpa->hpa
+ Nested guests:
+  non-tdp:       ngva->gpa->hpa  (*)
+  tdp:           (ngva->)ngpa->gpa->hpa
+
+(*) the guest hypervisor will encode the ngva->gpa translation into its page
+    tables if npt is not present
+
+Shadow pages contain the following information:
+  role.level:
+    The level in the shadow paging hierarchy that this shadow page belongs to.
+    1=4k sptes, 2=2M sptes, 3=1G sptes, etc.
+  role.direct:
+    If set, leaf sptes reachable from this page are for a linear range.
+    Examples include real mode translation, large guest pages backed by small
+    host pages, and gpa->hpa translations when NPT or EPT is active.
+    The linear range starts at (gfn << PAGE_SHIFT) and its size is determined
+    by role.level (2MB for first level, 1GB for second level, 0.5TB for third
+    level, 256TB for fourth level)
+    If clear, this page corresponds to a guest page table denoted by the gfn
+    field.
+  role.quadrant:
+    When role.cr4_pae=0, the guest uses 32-bit gptes while the host uses 64-bit
+    sptes.  That means a guest page table contains more ptes than the host,
+    so multiple shadow pages are needed to shadow one guest page.
+    For first-level shadow pages, role.quadrant can be 0 or 1 and denotes the
+    first or second 512-gpte block in the guest page table.  For second-level
+    page tables, each 32-bit gpte is converted to two 64-bit sptes
+    (since each first-level guest page is shadowed by two first-level
+    shadow pages) so role.quadrant takes values in the range 0..3.  Each
+    quadrant maps 1GB virtual address space.
+  role.access:
+    Inherited guest access permissions in the form uwx.  Note execute
+    permission is positive, not negative.
+  role.invalid:
+    The page is invalid and should not be used.  It is a root page that is
+    currently pinned (by a cpu hardware register pointing to it); once it is
+    unpinned it will be destroyed.
+  role.cr4_pae:
+    Contains the value of cr4.pae for which the page is valid (e.g. whether
+    32-bit or 64-bit gptes are in use).
+  role.nxe:
+    Contains the value of efer.nxe for which the page is valid.
+  role.cr0_wp:
+    Contains the value of cr0.wp for which the page is valid.
+  role.smep_andnot_wp:
+    Contains the value of cr4.smep && !cr0.wp for which the page is valid
+    (pages for which this is true are different from other pages; see the
+    treatment of cr0.wp=0 below).
+  role.smap_andnot_wp:
+    Contains the value of cr4.smap && !cr0.wp for which the page is valid
+    (pages for which this is true are different from other pages; see the
+    treatment of cr0.wp=0 below).
+  role.smm:
+    Is 1 if the page is valid in system management mode.  This field
+    determines which of the kvm_memslots array was used to build this
+    shadow page; it is also used to go back from a struct kvm_mmu_page
+    to a memslot, through the kvm_memslots_for_spte_role macro and
+    __gfn_to_memslot.
+  role.ad_disabled:
+    Is 1 if the MMU instance cannot use A/D bits.  EPT did not have A/D
+    bits before Haswell; shadow EPT page tables also cannot use A/D bits
+    if the L1 hypervisor does not enable them.
+  gfn:
+    Either the guest page table containing the translations shadowed by this
+    page, or the base page frame for linear translations.  See role.direct.
+  spt:
+    A pageful of 64-bit sptes containing the translations for this page.
+    Accessed by both kvm and hardware.
+    The page pointed to by spt will have its page->private pointing back
+    at the shadow page structure.
+    sptes in spt point either at guest pages, or at lower-level shadow pages.
+    Specifically, if sp1 and sp2 are shadow pages, then sp1->spt[n] may point
+    at __pa(sp2->spt).  sp2 will point back at sp1 through parent_pte.
+    The spt array forms a DAG structure with the shadow page as a node, and
+    guest pages as leaves.
+  gfns:
+    An array of 512 guest frame numbers, one for each present pte.  Used to
+    perform a reverse map from a pte to a gfn. When role.direct is set, any
+    element of this array can be calculated from the gfn field when used, in
+    this case, the array of gfns is not allocated. See role.direct and gfn.
+  root_count:
+    A counter keeping track of how many hardware registers (guest cr3 or
+    pdptrs) are now pointing at the page.  While this counter is nonzero, the
+    page cannot be destroyed.  See role.invalid.
+  parent_ptes:
+    The reverse mapping for the pte/ptes pointing at this page's spt. If
+    parent_ptes bit 0 is zero, only one spte points at this page and
+    parent_ptes points at this single spte, otherwise, there exists multiple
+    sptes pointing at this page and (parent_ptes & ~0x1) points at a data
+    structure with a list of parent sptes.
+  unsync:
+    If true, then the translations in this page may not match the guest's
+    translation.  This is equivalent to the state of the tlb when a pte is
+    changed but before the tlb entry is flushed.  Accordingly, unsync ptes
+    are synchronized when the guest executes invlpg or flushes its tlb by
+    other means.  Valid for leaf pages.
+  unsync_children:
+    How many sptes in the page point at pages that are unsync (or have
+    unsynchronized children).
+  unsync_child_bitmap:
+    A bitmap indicating which sptes in spt point (directly or indirectly) at
+    pages that may be unsynchronized.  Used to quickly locate all unsychronized
+    pages reachable from a given page.
+  mmu_valid_gen:
+    Generation number of the page.  It is compared with kvm->arch.mmu_valid_gen
+    during hash table lookup, and used to skip invalidated shadow pages (see
+    "Zapping all pages" below.)
+  clear_spte_count:
+    Only present on 32-bit hosts, where a 64-bit spte cannot be written
+    atomically.  The reader uses this while running out of the MMU lock
+    to detect in-progress updates and retry them until the writer has
+    finished the write.
+  write_flooding_count:
+    A guest may write to a page table many times, causing a lot of
+    emulations if the page needs to be write-protected (see "Synchronized
+    and unsynchronized pages" below).  Leaf pages can be unsynchronized
+    so that they do not trigger frequent emulation, but this is not
+    possible for non-leafs.  This field counts the number of emulations
+    since the last time the page table was actually used; if emulation
+    is triggered too frequently on this page, KVM will unmap the page
+    to avoid emulation in the future.
+
+Reverse map
+===========
+
+The mmu maintains a reverse mapping whereby all ptes mapping a page can be
+reached given its gfn.  This is used, for example, when swapping out a page.
+
+Synchronized and unsynchronized pages
+=====================================
+
+The guest uses two events to synchronize its tlb and page tables: tlb flushes
+and page invalidations (invlpg).
+
+A tlb flush means that we need to synchronize all sptes reachable from the
+guest's cr3.  This is expensive, so we keep all guest page tables write
+protected, and synchronize sptes to gptes when a gpte is written.
+
+A special case is when a guest page table is reachable from the current
+guest cr3.  In this case, the guest is obliged to issue an invlpg instruction
+before using the translation.  We take advantage of that by removing write
+protection from the guest page, and allowing the guest to modify it freely.
+We synchronize modified gptes when the guest invokes invlpg.  This reduces
+the amount of emulation we have to do when the guest modifies multiple gptes,
+or when the a guest page is no longer used as a page table and is used for
+random guest data.
+
+As a side effect we have to resynchronize all reachable unsynchronized shadow
+pages on a tlb flush.
+
+
+Reaction to events
+==================
+
+- guest page fault (or npt page fault, or ept violation)
+
+This is the most complicated event.  The cause of a page fault can be:
+
+  - a true guest fault (the guest translation won't allow the access) (*)
+  - access to a missing translation
+  - access to a protected translation
+    - when logging dirty pages, memory is write protected
+    - synchronized shadow pages are write protected (*)
+  - access to untranslatable memory (mmio)
+
+  (*) not applicable in direct mode
+
+Handling a page fault is performed as follows:
+
+ - if the RSV bit of the error code is set, the page fault is caused by guest
+   accessing MMIO and cached MMIO information is available.
+   - walk shadow page table
+   - check for valid generation number in the spte (see "Fast invalidation of
+     MMIO sptes" below)
+   - cache the information to vcpu->arch.mmio_gva, vcpu->arch.access and
+     vcpu->arch.mmio_gfn, and call the emulator
+ - If both P bit and R/W bit of error code are set, this could possibly
+   be handled as a "fast page fault" (fixed without taking the MMU lock).  See
+   the description in Documentation/virtual/kvm/locking.txt.
+ - if needed, walk the guest page tables to determine the guest translation
+   (gva->gpa or ngpa->gpa)
+   - if permissions are insufficient, reflect the fault back to the guest
+ - determine the host page
+   - if this is an mmio request, there is no host page; cache the info to
+     vcpu->arch.mmio_gva, vcpu->arch.access and vcpu->arch.mmio_gfn
+ - walk the shadow page table to find the spte for the translation,
+   instantiating missing intermediate page tables as necessary
+   - If this is an mmio request, cache the mmio info to the spte and set some
+     reserved bit on the spte (see callers of kvm_mmu_set_mmio_spte_mask)
+ - try to unsynchronize the page
+   - if successful, we can let the guest continue and modify the gpte
+ - emulate the instruction
+   - if failed, unshadow the page and let the guest continue
+ - update any translations that were modified by the instruction
+
+invlpg handling:
+
+  - walk the shadow page hierarchy and drop affected translations
+  - try to reinstantiate the indicated translation in the hope that the
+    guest will use it in the near future
+
+Guest control register updates:
+
+- mov to cr3
+  - look up new shadow roots
+  - synchronize newly reachable shadow pages
+
+- mov to cr0/cr4/efer
+  - set up mmu context for new paging mode
+  - look up new shadow roots
+  - synchronize newly reachable shadow pages
+
+Host translation updates:
+
+  - mmu notifier called with updated hva
+  - look up affected sptes through reverse map
+  - drop (or update) translations
+
+Emulating cr0.wp
+================
+
+If tdp is not enabled, the host must keep cr0.wp=1 so page write protection
+works for the guest kernel, not guest guest userspace.  When the guest
+cr0.wp=1, this does not present a problem.  However when the guest cr0.wp=0,
+we cannot map the permissions for gpte.u=1, gpte.w=0 to any spte (the
+semantics require allowing any guest kernel access plus user read access).
+
+We handle this by mapping the permissions to two possible sptes, depending
+on fault type:
+
+- kernel write fault: spte.u=0, spte.w=1 (allows full kernel access,
+  disallows user access)
+- read fault: spte.u=1, spte.w=0 (allows full read access, disallows kernel
+  write access)
+
+(user write faults generate a #PF)
+
+In the first case there are two additional complications:
+- if CR4.SMEP is enabled: since we've turned the page into a kernel page,
+  the kernel may now execute it.  We handle this by also setting spte.nx.
+  If we get a user fetch or read fault, we'll change spte.u=1 and
+  spte.nx=gpte.nx back.  For this to work, KVM forces EFER.NX to 1 when
+  shadow paging is in use.
+- if CR4.SMAP is disabled: since the page has been changed to a kernel
+  page, it can not be reused when CR4.SMAP is enabled. We set
+  CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note,
+  here we do not care the case that CR4.SMAP is enabled since KVM will
+  directly inject #PF to guest due to failed permission check.
+
+To prevent an spte that was converted into a kernel page with cr0.wp=0
+from being written by the kernel after cr0.wp has changed to 1, we make
+the value of cr0.wp part of the page role.  This means that an spte created
+with one value of cr0.wp cannot be used when cr0.wp has a different value -
+it will simply be missed by the shadow page lookup code.  A similar issue
+exists when an spte created with cr0.wp=0 and cr4.smep=0 is used after
+changing cr4.smep to 1.  To avoid this, the value of !cr0.wp && cr4.smep
+is also made a part of the page role.
+
+Large pages
+===========
+
+The mmu supports all combinations of large and small guest and host pages.
+Supported page sizes include 4k, 2M, 4M, and 1G.  4M pages are treated as
+two separate 2M pages, on both guest and host, since the mmu always uses PAE
+paging.
+
+To instantiate a large spte, four constraints must be satisfied:
+
+- the spte must point to a large host page
+- the guest pte must be a large pte of at least equivalent size (if tdp is
+  enabled, there is no guest pte and this condition is satisfied)
+- if the spte will be writeable, the large page frame may not overlap any
+  write-protected pages
+- the guest page must be wholly contained by a single memory slot
+
+To check the last two conditions, the mmu maintains a ->disallow_lpage set of
+arrays for each memory slot and large page size.  Every write protected page
+causes its disallow_lpage to be incremented, thus preventing instantiation of
+a large spte.  The frames at the end of an unaligned memory slot have
+artificially inflated ->disallow_lpages so they can never be instantiated.
+
+Zapping all pages (page generation count)
+=========================================
+
+For the large memory guests, walking and zapping all pages is really slow
+(because there are a lot of pages), and also blocks memory accesses of
+all VCPUs because it needs to hold the MMU lock.
+
+To make it be more scalable, kvm maintains a global generation number
+which is stored in kvm->arch.mmu_valid_gen.  Every shadow page stores
+the current global generation-number into sp->mmu_valid_gen when it
+is created.  Pages with a mismatching generation number are "obsolete".
+
+When KVM need zap all shadow pages sptes, it just simply increases the global
+generation-number then reload root shadow pages on all vcpus.  As the VCPUs
+create new shadow page tables, the old pages are not used because of the
+mismatching generation number.
+
+KVM then walks through all pages and zaps obsolete pages.  While the zap
+operation needs to take the MMU lock, the lock can be released periodically
+so that the VCPUs can make progress.
+
+Fast invalidation of MMIO sptes
+===============================
+
+As mentioned in "Reaction to events" above, kvm will cache MMIO
+information in leaf sptes.  When a new memslot is added or an existing
+memslot is changed, this information may become stale and needs to be
+invalidated.  This also needs to hold the MMU lock while walking all
+shadow pages, and is made more scalable with a similar technique.
+
+MMIO sptes have a few spare bits, which are used to store a
+generation number.  The global generation number is stored in
+kvm_memslots(kvm)->generation, and increased whenever guest memory info
+changes.  This generation number is distinct from the one described in
+the previous section.
+
+When KVM finds an MMIO spte, it checks the generation number of the spte.
+If the generation number of the spte does not equal the global generation
+number, it will ignore the cached MMIO information and handle the page
+fault through the slow path.
+
+Since only 19 bits are used to store generation-number on mmio spte, all
+pages are zapped when there is an overflow.
+
+Unfortunately, a single memory access might access kvm_memslots(kvm) multiple
+times, the last one happening when the generation number is retrieved and
+stored into the MMIO spte.  Thus, the MMIO spte might be created based on
+out-of-date information, but with an up-to-date generation number.
+
+To avoid this, the generation number is incremented again after synchronize_srcu
+returns; thus, the low bit of kvm_memslots(kvm)->generation is only 1 during a
+memslot update, while some SRCU readers might be using the old copy.  We do not
+want to use an MMIO sptes created with an odd generation number, and we can do
+this without losing a bit in the MMIO spte.  The low bit of the generation
+is not stored in MMIO spte, and presumed zero when it is extracted out of the
+spte.  If KVM is unlucky and creates an MMIO spte while the low bit is 1,
+the next access to the spte will always be a cache miss.
+
+
+Further reading
+===============
+
+- NPT presentation from KVM Forum 2008
+  http://www.linux-kvm.org/images/c/c8/KvmForum2008%24kdf2008_21.pdf
+
diff --git a/Documentation/virtual/kvm/msr.txt b/Documentation/virtual/kvm/msr.txt
new file mode 100644
index 0000000..f3f0d57
--- /dev/null
+++ b/Documentation/virtual/kvm/msr.txt
@@ -0,0 +1,275 @@
+KVM-specific MSRs.
+Glauber Costa <glommer@redhat.com>, Red Hat Inc, 2010
+=====================================================
+
+KVM makes use of some custom MSRs to service some requests.
+
+Custom MSRs have a range reserved for them, that goes from
+0x4b564d00 to 0x4b564dff. There are MSRs outside this area,
+but they are deprecated and their use is discouraged.
+
+Custom MSR list
+--------
+
+The current supported Custom MSR list is:
+
+MSR_KVM_WALL_CLOCK_NEW:   0x4b564d00
+
+	data: 4-byte alignment physical address of a memory area which must be
+	in guest RAM. This memory is expected to hold a copy of the following
+	structure:
+
+	struct pvclock_wall_clock {
+		u32   version;
+		u32   sec;
+		u32   nsec;
+	} __attribute__((__packed__));
+
+	whose data will be filled in by the hypervisor. The hypervisor is only
+	guaranteed to update this data at the moment of MSR write.
+	Users that want to reliably query this information more than once have
+	to write more than once to this MSR. Fields have the following meanings:
+
+		version: guest has to check version before and after grabbing
+		time information and check that they are both equal and even.
+		An odd version indicates an in-progress update.
+
+		sec: number of seconds for wallclock at time of boot.
+
+		nsec: number of nanoseconds for wallclock at time of boot.
+
+	In order to get the current wallclock time, the system_time from
+	MSR_KVM_SYSTEM_TIME_NEW needs to be added.
+
+	Note that although MSRs are per-CPU entities, the effect of this
+	particular MSR is global.
+
+	Availability of this MSR must be checked via bit 3 in 0x4000001 cpuid
+	leaf prior to usage.
+
+MSR_KVM_SYSTEM_TIME_NEW:  0x4b564d01
+
+	data: 4-byte aligned physical address of a memory area which must be in
+	guest RAM, plus an enable bit in bit 0. This memory is expected to hold
+	a copy of the following structure:
+
+	struct pvclock_vcpu_time_info {
+		u32   version;
+		u32   pad0;
+		u64   tsc_timestamp;
+		u64   system_time;
+		u32   tsc_to_system_mul;
+		s8    tsc_shift;
+		u8    flags;
+		u8    pad[2];
+	} __attribute__((__packed__)); /* 32 bytes */
+
+	whose data will be filled in by the hypervisor periodically. Only one
+	write, or registration, is needed for each VCPU. The interval between
+	updates of this structure is arbitrary and implementation-dependent.
+	The hypervisor may update this structure at any time it sees fit until
+	anything with bit0 == 0 is written to it.
+
+	Fields have the following meanings:
+
+		version: guest has to check version before and after grabbing
+		time information and check that they are both equal and even.
+		An odd version indicates an in-progress update.
+
+		tsc_timestamp: the tsc value at the current VCPU at the time
+		of the update of this structure. Guests can subtract this value
+		from current tsc to derive a notion of elapsed time since the
+		structure update.
+
+		system_time: a host notion of monotonic time, including sleep
+		time at the time this structure was last updated. Unit is
+		nanoseconds.
+
+		tsc_to_system_mul: multiplier to be used when converting
+		tsc-related quantity to nanoseconds
+
+		tsc_shift: shift to be used when converting tsc-related
+		quantity to nanoseconds. This shift will ensure that
+		multiplication with tsc_to_system_mul does not overflow.
+		A positive value denotes a left shift, a negative value
+		a right shift.
+
+		The conversion from tsc to nanoseconds involves an additional
+		right shift by 32 bits. With this information, guests can
+		derive per-CPU time by doing:
+
+			time = (current_tsc - tsc_timestamp)
+			if (tsc_shift >= 0)
+				time <<= tsc_shift;
+			else
+				time >>= -tsc_shift;
+			time = (time * tsc_to_system_mul) >> 32
+			time = time + system_time
+
+		flags: bits in this field indicate extended capabilities
+		coordinated between the guest and the hypervisor. Availability
+		of specific flags has to be checked in 0x40000001 cpuid leaf.
+		Current flags are:
+
+		 flag bit   | cpuid bit    | meaning
+		-------------------------------------------------------------
+			    |	           | time measures taken across
+		     0      |	   24      | multiple cpus are guaranteed to
+			    |		   | be monotonic
+		-------------------------------------------------------------
+			    |		   | guest vcpu has been paused by
+		     1	    |	  N/A	   | the host
+			    |		   | See 4.70 in api.txt
+		-------------------------------------------------------------
+
+	Availability of this MSR must be checked via bit 3 in 0x4000001 cpuid
+	leaf prior to usage.
+
+
+MSR_KVM_WALL_CLOCK:  0x11
+
+	data and functioning: same as MSR_KVM_WALL_CLOCK_NEW. Use that instead.
+
+	This MSR falls outside the reserved KVM range and may be removed in the
+	future. Its usage is deprecated.
+
+	Availability of this MSR must be checked via bit 0 in 0x4000001 cpuid
+	leaf prior to usage.
+
+MSR_KVM_SYSTEM_TIME: 0x12
+
+	data and functioning: same as MSR_KVM_SYSTEM_TIME_NEW. Use that instead.
+
+	This MSR falls outside the reserved KVM range and may be removed in the
+	future. Its usage is deprecated.
+
+	Availability of this MSR must be checked via bit 0 in 0x4000001 cpuid
+	leaf prior to usage.
+
+	The suggested algorithm for detecting kvmclock presence is then:
+
+		if (!kvm_para_available())    /* refer to cpuid.txt */
+			return NON_PRESENT;
+
+		flags = cpuid_eax(0x40000001);
+		if (flags & 3) {
+			msr_kvm_system_time = MSR_KVM_SYSTEM_TIME_NEW;
+			msr_kvm_wall_clock = MSR_KVM_WALL_CLOCK_NEW;
+			return PRESENT;
+		} else if (flags & 0) {
+			msr_kvm_system_time = MSR_KVM_SYSTEM_TIME;
+			msr_kvm_wall_clock = MSR_KVM_WALL_CLOCK;
+			return PRESENT;
+		} else
+			return NON_PRESENT;
+
+MSR_KVM_ASYNC_PF_EN: 0x4b564d02
+	data: Bits 63-6 hold 64-byte aligned physical address of a
+	64 byte memory area which must be in guest RAM and must be
+	zeroed. Bits 5-3 are reserved and should be zero. Bit 0 is 1
+	when asynchronous page faults are enabled on the vcpu 0 when
+	disabled. Bit 1 is 1 if asynchronous page faults can be injected
+	when vcpu is in cpl == 0. Bit 2 is 1 if asynchronous page faults
+	are delivered to L1 as #PF vmexits.  Bit 2 can be set only if
+	KVM_FEATURE_ASYNC_PF_VMEXIT is present in CPUID.
+
+	First 4 byte of 64 byte memory location will be written to by
+	the hypervisor at the time of asynchronous page fault (APF)
+	injection to indicate type of asynchronous page fault. Value
+	of 1 means that the page referred to by the page fault is not
+	present. Value 2 means that the page is now available. Disabling
+	interrupt inhibits APFs. Guest must not enable interrupt
+	before the reason is read, or it may be overwritten by another
+	APF. Since APF uses the same exception vector as regular page
+	fault guest must reset the reason to 0 before it does
+	something that can generate normal page fault.  If during page
+	fault APF reason is 0 it means that this is regular page
+	fault.
+
+	During delivery of type 1 APF cr2 contains a token that will
+	be used to notify a guest when missing page becomes
+	available. When page becomes available type 2 APF is sent with
+	cr2 set to the token associated with the page. There is special
+	kind of token 0xffffffff which tells vcpu that it should wake
+	up all processes waiting for APFs and no individual type 2 APFs
+	will be sent.
+
+	If APF is disabled while there are outstanding APFs, they will
+	not be delivered.
+
+	Currently type 2 APF will be always delivered on the same vcpu as
+	type 1 was, but guest should not rely on that.
+
+MSR_KVM_STEAL_TIME: 0x4b564d03
+
+	data: 64-byte alignment physical address of a memory area which must be
+	in guest RAM, plus an enable bit in bit 0. This memory is expected to
+	hold a copy of the following structure:
+
+	struct kvm_steal_time {
+		__u64 steal;
+		__u32 version;
+		__u32 flags;
+		__u8  preempted;
+		__u8  u8_pad[3];
+		__u32 pad[11];
+	}
+
+	whose data will be filled in by the hypervisor periodically. Only one
+	write, or registration, is needed for each VCPU. The interval between
+	updates of this structure is arbitrary and implementation-dependent.
+	The hypervisor may update this structure at any time it sees fit until
+	anything with bit0 == 0 is written to it. Guest is required to make sure
+	this structure is initialized to zero.
+
+	Fields have the following meanings:
+
+		version: a sequence counter. In other words, guest has to check
+		this field before and after grabbing time information and make
+		sure they are both equal and even. An odd version indicates an
+		in-progress update.
+
+		flags: At this point, always zero. May be used to indicate
+		changes in this structure in the future.
+
+		steal: the amount of time in which this vCPU did not run, in
+		nanoseconds. Time during which the vcpu is idle, will not be
+		reported as steal time.
+
+		preempted: indicate the vCPU who owns this struct is running or
+		not. Non-zero values mean the vCPU has been preempted. Zero
+		means the vCPU is not preempted. NOTE, it is always zero if the
+		the hypervisor doesn't support this field.
+
+MSR_KVM_EOI_EN: 0x4b564d04
+	data: Bit 0 is 1 when PV end of interrupt is enabled on the vcpu; 0
+	when disabled.  Bit 1 is reserved and must be zero.  When PV end of
+	interrupt is enabled (bit 0 set), bits 63-2 hold a 4-byte aligned
+	physical address of a 4 byte memory area which must be in guest RAM and
+	must be zeroed.
+
+	The first, least significant bit of 4 byte memory location will be
+	written to by the hypervisor, typically at the time of interrupt
+	injection.  Value of 1 means that guest can skip writing EOI to the apic
+	(using MSR or MMIO write); instead, it is sufficient to signal
+	EOI by clearing the bit in guest memory - this location will
+	later be polled by the hypervisor.
+	Value of 0 means that the EOI write is required.
+
+	It is always safe for the guest to ignore the optimization and perform
+	the APIC EOI write anyway.
+
+	Hypervisor is guaranteed to only modify this least
+	significant bit while in the current VCPU context, this means that
+	guest does not need to use either lock prefix or memory ordering
+	primitives to synchronise with the hypervisor.
+
+	However, hypervisor can set and clear this memory bit at any time:
+	therefore to make sure hypervisor does not interrupt the
+	guest and clear the least significant bit in the memory area
+	in the window between guest testing it to detect
+	whether it can skip EOI apic write and between guest
+	clearing it to signal EOI to the hypervisor,
+	guest must both read the least significant bit in the memory area and
+	clear it using a single CPU instruction, such as test and clear, or
+	compare and exchange.
diff --git a/Documentation/virtual/kvm/nested-vmx.txt b/Documentation/virtual/kvm/nested-vmx.txt
new file mode 100644
index 0000000..97eb135
--- /dev/null
+++ b/Documentation/virtual/kvm/nested-vmx.txt
@@ -0,0 +1,240 @@
+Nested VMX
+==========
+
+Overview
+---------
+
+On Intel processors, KVM uses Intel's VMX (Virtual-Machine eXtensions)
+to easily and efficiently run guest operating systems. Normally, these guests
+*cannot* themselves be hypervisors running their own guests, because in VMX,
+guests cannot use VMX instructions.
+
+The "Nested VMX" feature adds this missing capability - of running guest
+hypervisors (which use VMX) with their own nested guests. It does so by
+allowing a guest to use VMX instructions, and correctly and efficiently
+emulating them using the single level of VMX available in the hardware.
+
+We describe in much greater detail the theory behind the nested VMX feature,
+its implementation and its performance characteristics, in the OSDI 2010 paper
+"The Turtles Project: Design and Implementation of Nested Virtualization",
+available at:
+
+	http://www.usenix.org/events/osdi10/tech/full_papers/Ben-Yehuda.pdf
+
+
+Terminology
+-----------
+
+Single-level virtualization has two levels - the host (KVM) and the guests.
+In nested virtualization, we have three levels: The host (KVM), which we call
+L0, the guest hypervisor, which we call L1, and its nested guest, which we
+call L2.
+
+
+Running nested VMX
+------------------
+
+The nested VMX feature is disabled by default. It can be enabled by giving
+the "nested=1" option to the kvm-intel module.
+
+No modifications are required to user space (qemu). However, qemu's default
+emulated CPU type (qemu64) does not list the "VMX" CPU feature, so it must be
+explicitly enabled, by giving qemu one of the following options:
+
+     -cpu host              (emulated CPU has all features of the real CPU)
+
+     -cpu qemu64,+vmx       (add just the vmx feature to a named CPU type)
+
+
+ABIs
+----
+
+Nested VMX aims to present a standard and (eventually) fully-functional VMX
+implementation for the a guest hypervisor to use. As such, the official
+specification of the ABI that it provides is Intel's VMX specification,
+namely volume 3B of their "Intel 64 and IA-32 Architectures Software
+Developer's Manual". Not all of VMX's features are currently fully supported,
+but the goal is to eventually support them all, starting with the VMX features
+which are used in practice by popular hypervisors (KVM and others).
+
+As a VMX implementation, nested VMX presents a VMCS structure to L1.
+As mandated by the spec, other than the two fields revision_id and abort,
+this structure is *opaque* to its user, who is not supposed to know or care
+about its internal structure. Rather, the structure is accessed through the
+VMREAD and VMWRITE instructions.
+Still, for debugging purposes, KVM developers might be interested to know the
+internals of this structure; This is struct vmcs12 from arch/x86/kvm/vmx.c.
+
+The name "vmcs12" refers to the VMCS that L1 builds for L2. In the code we
+also have "vmcs01", the VMCS that L0 built for L1, and "vmcs02" is the VMCS
+which L0 builds to actually run L2 - how this is done is explained in the
+aforementioned paper.
+
+For convenience, we repeat the content of struct vmcs12 here. If the internals
+of this structure changes, this can break live migration across KVM versions.
+VMCS12_REVISION (from vmx.c) should be changed if struct vmcs12 or its inner
+struct shadow_vmcs is ever changed.
+
+	typedef u64 natural_width;
+	struct __packed vmcs12 {
+		/* According to the Intel spec, a VMCS region must start with
+		 * these two user-visible fields */
+		u32 revision_id;
+		u32 abort;
+
+		u32 launch_state; /* set to 0 by VMCLEAR, to 1 by VMLAUNCH */
+		u32 padding[7]; /* room for future expansion */
+
+		u64 io_bitmap_a;
+		u64 io_bitmap_b;
+		u64 msr_bitmap;
+		u64 vm_exit_msr_store_addr;
+		u64 vm_exit_msr_load_addr;
+		u64 vm_entry_msr_load_addr;
+		u64 tsc_offset;
+		u64 virtual_apic_page_addr;
+		u64 apic_access_addr;
+		u64 ept_pointer;
+		u64 guest_physical_address;
+		u64 vmcs_link_pointer;
+		u64 guest_ia32_debugctl;
+		u64 guest_ia32_pat;
+		u64 guest_ia32_efer;
+		u64 guest_pdptr0;
+		u64 guest_pdptr1;
+		u64 guest_pdptr2;
+		u64 guest_pdptr3;
+		u64 host_ia32_pat;
+		u64 host_ia32_efer;
+		u64 padding64[8]; /* room for future expansion */
+		natural_width cr0_guest_host_mask;
+		natural_width cr4_guest_host_mask;
+		natural_width cr0_read_shadow;
+		natural_width cr4_read_shadow;
+		natural_width cr3_target_value0;
+		natural_width cr3_target_value1;
+		natural_width cr3_target_value2;
+		natural_width cr3_target_value3;
+		natural_width exit_qualification;
+		natural_width guest_linear_address;
+		natural_width guest_cr0;
+		natural_width guest_cr3;
+		natural_width guest_cr4;
+		natural_width guest_es_base;
+		natural_width guest_cs_base;
+		natural_width guest_ss_base;
+		natural_width guest_ds_base;
+		natural_width guest_fs_base;
+		natural_width guest_gs_base;
+		natural_width guest_ldtr_base;
+		natural_width guest_tr_base;
+		natural_width guest_gdtr_base;
+		natural_width guest_idtr_base;
+		natural_width guest_dr7;
+		natural_width guest_rsp;
+		natural_width guest_rip;
+		natural_width guest_rflags;
+		natural_width guest_pending_dbg_exceptions;
+		natural_width guest_sysenter_esp;
+		natural_width guest_sysenter_eip;
+		natural_width host_cr0;
+		natural_width host_cr3;
+		natural_width host_cr4;
+		natural_width host_fs_base;
+		natural_width host_gs_base;
+		natural_width host_tr_base;
+		natural_width host_gdtr_base;
+		natural_width host_idtr_base;
+		natural_width host_ia32_sysenter_esp;
+		natural_width host_ia32_sysenter_eip;
+		natural_width host_rsp;
+		natural_width host_rip;
+		natural_width paddingl[8]; /* room for future expansion */
+		u32 pin_based_vm_exec_control;
+		u32 cpu_based_vm_exec_control;
+		u32 exception_bitmap;
+		u32 page_fault_error_code_mask;
+		u32 page_fault_error_code_match;
+		u32 cr3_target_count;
+		u32 vm_exit_controls;
+		u32 vm_exit_msr_store_count;
+		u32 vm_exit_msr_load_count;
+		u32 vm_entry_controls;
+		u32 vm_entry_msr_load_count;
+		u32 vm_entry_intr_info_field;
+		u32 vm_entry_exception_error_code;
+		u32 vm_entry_instruction_len;
+		u32 tpr_threshold;
+		u32 secondary_vm_exec_control;
+		u32 vm_instruction_error;
+		u32 vm_exit_reason;
+		u32 vm_exit_intr_info;
+		u32 vm_exit_intr_error_code;
+		u32 idt_vectoring_info_field;
+		u32 idt_vectoring_error_code;
+		u32 vm_exit_instruction_len;
+		u32 vmx_instruction_info;
+		u32 guest_es_limit;
+		u32 guest_cs_limit;
+		u32 guest_ss_limit;
+		u32 guest_ds_limit;
+		u32 guest_fs_limit;
+		u32 guest_gs_limit;
+		u32 guest_ldtr_limit;
+		u32 guest_tr_limit;
+		u32 guest_gdtr_limit;
+		u32 guest_idtr_limit;
+		u32 guest_es_ar_bytes;
+		u32 guest_cs_ar_bytes;
+		u32 guest_ss_ar_bytes;
+		u32 guest_ds_ar_bytes;
+		u32 guest_fs_ar_bytes;
+		u32 guest_gs_ar_bytes;
+		u32 guest_ldtr_ar_bytes;
+		u32 guest_tr_ar_bytes;
+		u32 guest_interruptibility_info;
+		u32 guest_activity_state;
+		u32 guest_sysenter_cs;
+		u32 host_ia32_sysenter_cs;
+		u32 padding32[8]; /* room for future expansion */
+		u16 virtual_processor_id;
+		u16 guest_es_selector;
+		u16 guest_cs_selector;
+		u16 guest_ss_selector;
+		u16 guest_ds_selector;
+		u16 guest_fs_selector;
+		u16 guest_gs_selector;
+		u16 guest_ldtr_selector;
+		u16 guest_tr_selector;
+		u16 host_es_selector;
+		u16 host_cs_selector;
+		u16 host_ss_selector;
+		u16 host_ds_selector;
+		u16 host_fs_selector;
+		u16 host_gs_selector;
+		u16 host_tr_selector;
+	};
+
+
+Authors
+-------
+
+These patches were written by:
+     Abel Gordon, abelg <at> il.ibm.com
+     Nadav Har'El, nyh <at> il.ibm.com
+     Orit Wasserman, oritw <at> il.ibm.com
+     Ben-Ami Yassor, benami <at> il.ibm.com
+     Muli Ben-Yehuda, muli <at> il.ibm.com
+
+With contributions by:
+     Anthony Liguori, aliguori <at> us.ibm.com
+     Mike Day, mdday <at> us.ibm.com
+     Michael Factor, factor <at> il.ibm.com
+     Zvi Dubitzky, dubi <at> il.ibm.com
+
+And valuable reviews by:
+     Avi Kivity, avi <at> redhat.com
+     Gleb Natapov, gleb <at> redhat.com
+     Marcelo Tosatti, mtosatti <at> redhat.com
+     Kevin Tian, kevin.tian <at> intel.com
+     and others.
diff --git a/Documentation/virtual/kvm/ppc-pv.txt b/Documentation/virtual/kvm/ppc-pv.txt
new file mode 100644
index 0000000..e26115c
--- /dev/null
+++ b/Documentation/virtual/kvm/ppc-pv.txt
@@ -0,0 +1,212 @@
+The PPC KVM paravirtual interface
+=================================
+
+The basic execution principle by which KVM on PowerPC works is to run all kernel
+space code in PR=1 which is user space. This way we trap all privileged
+instructions and can emulate them accordingly.
+
+Unfortunately that is also the downfall. There are quite some privileged
+instructions that needlessly return us to the hypervisor even though they
+could be handled differently.
+
+This is what the PPC PV interface helps with. It takes privileged instructions
+and transforms them into unprivileged ones with some help from the hypervisor.
+This cuts down virtualization costs by about 50% on some of my benchmarks.
+
+The code for that interface can be found in arch/powerpc/kernel/kvm*
+
+Querying for existence
+======================
+
+To find out if we're running on KVM or not, we leverage the device tree. When
+Linux is running on KVM, a node /hypervisor exists. That node contains a
+compatible property with the value "linux,kvm".
+
+Once you determined you're running under a PV capable KVM, you can now use
+hypercalls as described below.
+
+KVM hypercalls
+==============
+
+Inside the device tree's /hypervisor node there's a property called
+'hypercall-instructions'. This property contains at most 4 opcodes that make
+up the hypercall. To call a hypercall, just call these instructions.
+
+The parameters are as follows:
+
+	Register	IN			OUT
+
+	r0		-			volatile
+	r3		1st parameter		Return code
+	r4		2nd parameter		1st output value
+	r5		3rd parameter		2nd output value
+	r6		4th parameter		3rd output value
+	r7		5th parameter		4th output value
+	r8		6th parameter		5th output value
+	r9		7th parameter		6th output value
+	r10		8th parameter		7th output value
+	r11		hypercall number	8th output value
+	r12		-			volatile
+
+Hypercall definitions are shared in generic code, so the same hypercall numbers
+apply for x86 and powerpc alike with the exception that each KVM hypercall
+also needs to be ORed with the KVM vendor code which is (42 << 16).
+
+Return codes can be as follows:
+
+	Code		Meaning
+
+	0		Success
+	12		Hypercall not implemented
+	<0		Error
+
+The magic page
+==============
+
+To enable communication between the hypervisor and guest there is a new shared
+page that contains parts of supervisor visible register state. The guest can
+map this shared page using the KVM hypercall KVM_HC_PPC_MAP_MAGIC_PAGE.
+
+With this hypercall issued the guest always gets the magic page mapped at the
+desired location. The first parameter indicates the effective address when the
+MMU is enabled. The second parameter indicates the address in real mode, if
+applicable to the target. For now, we always map the page to -4096. This way we
+can access it using absolute load and store functions. The following
+instruction reads the first field of the magic page:
+
+	ld	rX, -4096(0)
+
+The interface is designed to be extensible should there be need later to add
+additional registers to the magic page. If you add fields to the magic page,
+also define a new hypercall feature to indicate that the host can give you more
+registers. Only if the host supports the additional features, make use of them.
+
+The magic page layout is described by struct kvm_vcpu_arch_shared
+in arch/powerpc/include/asm/kvm_para.h.
+
+Magic page features
+===================
+
+When mapping the magic page using the KVM hypercall KVM_HC_PPC_MAP_MAGIC_PAGE,
+a second return value is passed to the guest. This second return value contains
+a bitmap of available features inside the magic page.
+
+The following enhancements to the magic page are currently available:
+
+  KVM_MAGIC_FEAT_SR		Maps SR registers r/w in the magic page
+  KVM_MAGIC_FEAT_MAS0_TO_SPRG7	Maps MASn, ESR, PIR and high SPRGs
+
+For enhanced features in the magic page, please check for the existence of the
+feature before using them!
+
+Magic page flags
+================
+
+In addition to features that indicate whether a host is capable of a particular
+feature we also have a channel for a guest to tell the guest whether it's capable
+of something. This is what we call "flags".
+
+Flags are passed to the host in the low 12 bits of the Effective Address.
+
+The following flags are currently available for a guest to expose:
+
+  MAGIC_PAGE_FLAG_NOT_MAPPED_NX Guest handles NX bits correctly wrt magic page
+
+MSR bits
+========
+
+The MSR contains bits that require hypervisor intervention and bits that do
+not require direct hypervisor intervention because they only get interpreted
+when entering the guest or don't have any impact on the hypervisor's behavior.
+
+The following bits are safe to be set inside the guest:
+
+  MSR_EE
+  MSR_RI
+
+If any other bit changes in the MSR, please still use mtmsr(d).
+
+Patched instructions
+====================
+
+The "ld" and "std" instructions are transformed to "lwz" and "stw" instructions
+respectively on 32 bit systems with an added offset of 4 to accommodate for big
+endianness.
+
+The following is a list of mapping the Linux kernel performs when running as
+guest. Implementing any of those mappings is optional, as the instruction traps
+also act on the shared page. So calling privileged instructions still works as
+before.
+
+From			To
+====			==
+
+mfmsr	rX		ld	rX, magic_page->msr
+mfsprg	rX, 0		ld	rX, magic_page->sprg0
+mfsprg	rX, 1		ld	rX, magic_page->sprg1
+mfsprg	rX, 2		ld	rX, magic_page->sprg2
+mfsprg	rX, 3		ld	rX, magic_page->sprg3
+mfsrr0	rX		ld	rX, magic_page->srr0
+mfsrr1	rX		ld	rX, magic_page->srr1
+mfdar	rX		ld	rX, magic_page->dar
+mfdsisr	rX		lwz	rX, magic_page->dsisr
+
+mtmsr	rX		std	rX, magic_page->msr
+mtsprg	0, rX		std	rX, magic_page->sprg0
+mtsprg	1, rX		std	rX, magic_page->sprg1
+mtsprg	2, rX		std	rX, magic_page->sprg2
+mtsprg	3, rX		std	rX, magic_page->sprg3
+mtsrr0	rX		std	rX, magic_page->srr0
+mtsrr1	rX		std	rX, magic_page->srr1
+mtdar	rX		std	rX, magic_page->dar
+mtdsisr	rX		stw	rX, magic_page->dsisr
+
+tlbsync			nop
+
+mtmsrd	rX, 0		b	<special mtmsr section>
+mtmsr	rX		b	<special mtmsr section>
+
+mtmsrd	rX, 1		b	<special mtmsrd section>
+
+[Book3S only]
+mtsrin	rX, rY		b	<special mtsrin section>
+
+[BookE only]
+wrteei	[0|1]		b	<special wrteei section>
+
+
+Some instructions require more logic to determine what's going on than a load
+or store instruction can deliver. To enable patching of those, we keep some
+RAM around where we can live translate instructions to. What happens is the
+following:
+
+	1) copy emulation code to memory
+	2) patch that code to fit the emulated instruction
+	3) patch that code to return to the original pc + 4
+	4) patch the original instruction to branch to the new code
+
+That way we can inject an arbitrary amount of code as replacement for a single
+instruction. This allows us to check for pending interrupts when setting EE=1
+for example.
+
+Hypercall ABIs in KVM on PowerPC
+=================================
+1) KVM hypercalls (ePAPR)
+
+These are ePAPR compliant hypercall implementation (mentioned above). Even
+generic hypercalls are implemented here, like the ePAPR idle hcall. These are
+available on all targets.
+
+2) PAPR hypercalls
+
+PAPR hypercalls are needed to run server PowerPC PAPR guests (-M pseries in QEMU).
+These are the same hypercalls that pHyp, the POWER hypervisor implements. Some of
+them are handled in the kernel, some are handled in user space. This is only
+available on book3s_64.
+
+3) OSI hypercalls
+
+Mac-on-Linux is another user of KVM on PowerPC, which has its own hypercall (long
+before KVM). This is supported to maintain compatibility. All these hypercalls get
+forwarded to user space. This is only useful on book3s_32, but can be used with
+book3s_64 as well.
diff --git a/Documentation/virtual/kvm/review-checklist.txt b/Documentation/virtual/kvm/review-checklist.txt
new file mode 100644
index 0000000..a83b276
--- /dev/null
+++ b/Documentation/virtual/kvm/review-checklist.txt
@@ -0,0 +1,38 @@
+Review checklist for kvm patches
+================================
+
+1.  The patch must follow Documentation/process/coding-style.rst and
+    Documentation/process/submitting-patches.rst.
+
+2.  Patches should be against kvm.git master branch.
+
+3.  If the patch introduces or modifies a new userspace API:
+    - the API must be documented in Documentation/virtual/kvm/api.txt
+    - the API must be discoverable using KVM_CHECK_EXTENSION
+
+4.  New state must include support for save/restore.
+
+5.  New features must default to off (userspace should explicitly request them).
+    Performance improvements can and should default to on.
+
+6.  New cpu features should be exposed via KVM_GET_SUPPORTED_CPUID2
+
+7.  Emulator changes should be accompanied by unit tests for qemu-kvm.git
+    kvm/test directory.
+
+8.  Changes should be vendor neutral when possible.  Changes to common code
+    are better than duplicating changes to vendor code.
+
+9.  Similarly, prefer changes to arch independent code than to arch dependent
+    code.
+
+10. User/kernel interfaces and guest/host interfaces must be 64-bit clean
+    (all variables and sizes naturally aligned on 64-bit; use specific types
+    only - u64 rather than ulong).
+
+11. New guest visible features must either be documented in a hardware manual
+    or be accompanied by documentation.
+
+12. Features must be robust against reset and kexec - for example, shared
+    host/guest memory must be unshared to prevent the host from writing to
+    guest memory that the guest has not reserved for this purpose.
diff --git a/Documentation/virtual/kvm/s390-diag.txt b/Documentation/virtual/kvm/s390-diag.txt
new file mode 100644
index 0000000..48c4921
--- /dev/null
+++ b/Documentation/virtual/kvm/s390-diag.txt
@@ -0,0 +1,82 @@
+The s390 DIAGNOSE call on KVM
+=============================
+
+KVM on s390 supports the DIAGNOSE call for making hypercalls, both for
+native hypercalls and for selected hypercalls found on other s390
+hypervisors.
+
+Note that bits are numbered as by the usual s390 convention (most significant
+bit on the left).
+
+
+General remarks
+---------------
+
+DIAGNOSE calls by the guest cause a mandatory intercept. This implies
+all supported DIAGNOSE calls need to be handled by either KVM or its
+userspace.
+
+All DIAGNOSE calls supported by KVM use the RS-a format:
+
+--------------------------------------
+|  '83'  | R1 | R3 | B2 |     D2     |
+--------------------------------------
+0        8    12   16   20           31
+
+The second-operand address (obtained by the base/displacement calculation)
+is not used to address data. Instead, bits 48-63 of this address specify
+the function code, and bits 0-47 are ignored.
+
+The supported DIAGNOSE function codes vary by the userspace used. For
+DIAGNOSE function codes not specific to KVM, please refer to the
+documentation for the s390 hypervisors defining them.
+
+
+DIAGNOSE function code 'X'500' - KVM virtio functions
+-----------------------------------------------------
+
+If the function code specifies 0x500, various virtio-related functions
+are performed.
+
+General register 1 contains the virtio subfunction code. Supported
+virtio subfunctions depend on KVM's userspace. Generally, userspace
+provides either s390-virtio (subcodes 0-2) or virtio-ccw (subcode 3).
+
+Upon completion of the DIAGNOSE instruction, general register 2 contains
+the function's return code, which is either a return code or a subcode
+specific value.
+
+Subcode 0 - s390-virtio notification and early console printk
+    Handled by userspace.
+
+Subcode 1 - s390-virtio reset
+    Handled by userspace.
+
+Subcode 2 - s390-virtio set status
+    Handled by userspace.
+
+Subcode 3 - virtio-ccw notification
+    Handled by either userspace or KVM (ioeventfd case).
+
+    General register 2 contains a subchannel-identification word denoting
+    the subchannel of the virtio-ccw proxy device to be notified.
+
+    General register 3 contains the number of the virtqueue to be notified.
+
+    General register 4 contains a 64bit identifier for KVM usage (the
+    kvm_io_bus cookie). If general register 4 does not contain a valid
+    identifier, it is ignored.
+
+    After completion of the DIAGNOSE call, general register 2 may contain
+    a 64bit identifier (in the kvm_io_bus cookie case).
+
+    See also the virtio standard for a discussion of this hypercall.
+
+
+DIAGNOSE function code 'X'501 - KVM breakpoint
+----------------------------------------------
+
+If the function code specifies 0x501, breakpoint functions may be performed.
+This function code is handled by userspace.
+
+This diagnose function code has no subfunctions and uses no parameters.
diff --git a/Documentation/virtual/kvm/timekeeping.txt b/Documentation/virtual/kvm/timekeeping.txt
new file mode 100644
index 0000000..76808a1
--- /dev/null
+++ b/Documentation/virtual/kvm/timekeeping.txt
@@ -0,0 +1,612 @@
+
+	Timekeeping Virtualization for X86-Based Architectures
+
+	Zachary Amsden <zamsden@redhat.com>
+	Copyright (c) 2010, Red Hat.  All rights reserved.
+
+1) Overview
+2) Timing Devices
+3) TSC Hardware
+4) Virtualization Problems
+
+=========================================================================
+
+1) Overview
+
+One of the most complicated parts of the X86 platform, and specifically,
+the virtualization of this platform is the plethora of timing devices available
+and the complexity of emulating those devices.  In addition, virtualization of
+time introduces a new set of challenges because it introduces a multiplexed
+division of time beyond the control of the guest CPU.
+
+First, we will describe the various timekeeping hardware available, then
+present some of the problems which arise and solutions available, giving
+specific recommendations for certain classes of KVM guests.
+
+The purpose of this document is to collect data and information relevant to
+timekeeping which may be difficult to find elsewhere, specifically,
+information relevant to KVM and hardware-based virtualization.
+
+=========================================================================
+
+2) Timing Devices
+
+First we discuss the basic hardware devices available.  TSC and the related
+KVM clock are special enough to warrant a full exposition and are described in
+the following section.
+
+2.1) i8254 - PIT
+
+One of the first timer devices available is the programmable interrupt timer,
+or PIT.  The PIT has a fixed frequency 1.193182 MHz base clock and three
+channels which can be programmed to deliver periodic or one-shot interrupts.
+These three channels can be configured in different modes and have individual
+counters.  Channel 1 and 2 were not available for general use in the original
+IBM PC, and historically were connected to control RAM refresh and the PC
+speaker.  Now the PIT is typically integrated as part of an emulated chipset
+and a separate physical PIT is not used.
+
+The PIT uses I/O ports 0x40 - 0x43.  Access to the 16-bit counters is done
+using single or multiple byte access to the I/O ports.  There are 6 modes
+available, but not all modes are available to all timers, as only timer 2
+has a connected gate input, required for modes 1 and 5.  The gate line is
+controlled by port 61h, bit 0, as illustrated in the following diagram.
+
+ --------------             ----------------
+|              |           |                |
+|  1.1932 MHz  |---------->| CLOCK      OUT | ---------> IRQ 0
+|    Clock     |   |       |                |
+ --------------    |    +->| GATE  TIMER 0  |
+                   |        ----------------
+                   |
+                   |        ----------------
+                   |       |                |
+                   |------>| CLOCK      OUT | ---------> 66.3 KHZ DRAM
+                   |       |                |            (aka /dev/null)
+                   |    +->| GATE  TIMER 1  |
+                   |        ----------------
+                   |
+                   |        ----------------
+                   |       |                |
+                   |------>| CLOCK      OUT | ---------> Port 61h, bit 5
+                           |                |      |
+Port 61h, bit 0 ---------->| GATE  TIMER 2  |       \_.----   ____
+                            ----------------         _|    )--|LPF|---Speaker
+                                                    / *----   \___/
+Port 61h, bit 1 -----------------------------------/
+
+The timer modes are now described.
+
+Mode 0: Single Timeout.   This is a one-shot software timeout that counts down
+ when the gate is high (always true for timers 0 and 1).  When the count
+ reaches zero, the output goes high.
+
+Mode 1: Triggered One-shot.  The output is initially set high.  When the gate
+ line is set high, a countdown is initiated (which does not stop if the gate is
+ lowered), during which the output is set low.  When the count reaches zero,
+ the output goes high.
+
+Mode 2: Rate Generator.  The output is initially set high.  When the countdown
+ reaches 1, the output goes low for one count and then returns high.  The value
+ is reloaded and the countdown automatically resumes.  If the gate line goes
+ low, the count is halted.  If the output is low when the gate is lowered, the
+ output automatically goes high (this only affects timer 2).
+
+Mode 3: Square Wave.   This generates a high / low square wave.  The count
+ determines the length of the pulse, which alternates between high and low
+ when zero is reached.  The count only proceeds when gate is high and is
+ automatically reloaded on reaching zero.  The count is decremented twice at
+ each clock to generate a full high / low cycle at the full periodic rate.
+ If the count is even, the clock remains high for N/2 counts and low for N/2
+ counts; if the clock is odd, the clock is high for (N+1)/2 counts and low
+ for (N-1)/2 counts.  Only even values are latched by the counter, so odd
+ values are not observed when reading.  This is the intended mode for timer 2,
+ which generates sine-like tones by low-pass filtering the square wave output.
+
+Mode 4: Software Strobe.  After programming this mode and loading the counter,
+ the output remains high until the counter reaches zero.  Then the output
+ goes low for 1 clock cycle and returns high.  The counter is not reloaded.
+ Counting only occurs when gate is high.
+
+Mode 5: Hardware Strobe.  After programming and loading the counter, the
+ output remains high.  When the gate is raised, a countdown is initiated
+ (which does not stop if the gate is lowered).  When the counter reaches zero,
+ the output goes low for 1 clock cycle and then returns high.  The counter is
+ not reloaded.
+
+In addition to normal binary counting, the PIT supports BCD counting.  The
+command port, 0x43 is used to set the counter and mode for each of the three
+timers.
+
+PIT commands, issued to port 0x43, using the following bit encoding:
+
+Bit 7-4: Command (See table below)
+Bit 3-1: Mode (000 = Mode 0, 101 = Mode 5, 11X = undefined)
+Bit 0  : Binary (0) / BCD (1)
+
+Command table:
+
+0000 - Latch Timer 0 count for port 0x40
+	sample and hold the count to be read in port 0x40;
+	additional commands ignored until counter is read;
+	mode bits ignored.
+
+0001 - Set Timer 0 LSB mode for port 0x40
+	set timer to read LSB only and force MSB to zero;
+	mode bits set timer mode
+
+0010 - Set Timer 0 MSB mode for port 0x40
+	set timer to read MSB only and force LSB to zero;
+	mode bits set timer mode
+
+0011 - Set Timer 0 16-bit mode for port 0x40
+	set timer to read / write LSB first, then MSB;
+	mode bits set timer mode
+
+0100 - Latch Timer 1 count for port 0x41 - as described above
+0101 - Set Timer 1 LSB mode for port 0x41 - as described above
+0110 - Set Timer 1 MSB mode for port 0x41 - as described above
+0111 - Set Timer 1 16-bit mode for port 0x41 - as described above
+
+1000 - Latch Timer 2 count for port 0x42 - as described above
+1001 - Set Timer 2 LSB mode for port 0x42 - as described above
+1010 - Set Timer 2 MSB mode for port 0x42 - as described above
+1011 - Set Timer 2 16-bit mode for port 0x42 as described above
+
+1101 - General counter latch
+	Latch combination of counters into corresponding ports
+	Bit 3 = Counter 2
+	Bit 2 = Counter 1
+	Bit 1 = Counter 0
+	Bit 0 = Unused
+
+1110 - Latch timer status
+	Latch combination of counter mode into corresponding ports
+	Bit 3 = Counter 2
+	Bit 2 = Counter 1
+	Bit 1 = Counter 0
+
+	The output of ports 0x40-0x42 following this command will be:
+
+	Bit 7 = Output pin
+	Bit 6 = Count loaded (0 if timer has expired)
+	Bit 5-4 = Read / Write mode
+	    01 = MSB only
+	    10 = LSB only
+	    11 = LSB / MSB (16-bit)
+	Bit 3-1 = Mode
+	Bit 0 = Binary (0) / BCD mode (1)
+
+2.2) RTC
+
+The second device which was available in the original PC was the MC146818 real
+time clock.  The original device is now obsolete, and usually emulated by the
+system chipset, sometimes by an HPET and some frankenstein IRQ routing.
+
+The RTC is accessed through CMOS variables, which uses an index register to
+control which bytes are read.  Since there is only one index register, read
+of the CMOS and read of the RTC require lock protection (in addition, it is
+dangerous to allow userspace utilities such as hwclock to have direct RTC
+access, as they could corrupt kernel reads and writes of CMOS memory).
+
+The RTC generates an interrupt which is usually routed to IRQ 8.  The interrupt
+can function as a periodic timer, an additional once a day alarm, and can issue
+interrupts after an update of the CMOS registers by the MC146818 is complete.
+The type of interrupt is signalled in the RTC status registers.
+
+The RTC will update the current time fields by battery power even while the
+system is off.  The current time fields should not be read while an update is
+in progress, as indicated in the status register.
+
+The clock uses a 32.768kHz crystal, so bits 6-4 of register A should be
+programmed to a 32kHz divider if the RTC is to count seconds.
+
+This is the RAM map originally used for the RTC/CMOS:
+
+Location    Size    Description
+------------------------------------------
+00h         byte    Current second (BCD)
+01h         byte    Seconds alarm (BCD)
+02h         byte    Current minute (BCD)
+03h         byte    Minutes alarm (BCD)
+04h         byte    Current hour (BCD)
+05h         byte    Hours alarm (BCD)
+06h         byte    Current day of week (BCD)
+07h         byte    Current day of month (BCD)
+08h         byte    Current month (BCD)
+09h         byte    Current year (BCD)
+0Ah         byte    Register A
+                       bit 7   = Update in progress
+                       bit 6-4 = Divider for clock
+                                  000 = 4.194 MHz
+                                  001 = 1.049 MHz
+                                  010 = 32 kHz
+                                  10X = test modes
+                                  110 = reset / disable
+                                  111 = reset / disable
+                       bit 3-0 = Rate selection for periodic interrupt
+                                  000 = periodic timer disabled
+                                  001 = 3.90625 uS
+                                  010 = 7.8125 uS
+                                  011 = .122070 mS
+                                  100 = .244141 mS
+                                     ...
+                                 1101 = 125 mS
+                                 1110 = 250 mS
+                                 1111 = 500 mS
+0Bh         byte    Register B
+                       bit 7   = Run (0) / Halt (1)
+                       bit 6   = Periodic interrupt enable
+                       bit 5   = Alarm interrupt enable
+                       bit 4   = Update-ended interrupt enable
+                       bit 3   = Square wave interrupt enable
+                       bit 2   = BCD calendar (0) / Binary (1)
+                       bit 1   = 12-hour mode (0) / 24-hour mode (1)
+                       bit 0   = 0 (DST off) / 1 (DST enabled)
+OCh         byte    Register C (read only)
+                       bit 7   = interrupt request flag (IRQF)
+                       bit 6   = periodic interrupt flag (PF)
+                       bit 5   = alarm interrupt flag (AF)
+                       bit 4   = update interrupt flag (UF)
+                       bit 3-0 = reserved
+ODh         byte    Register D (read only)
+                       bit 7   = RTC has power
+                       bit 6-0 = reserved
+32h         byte    Current century BCD (*)
+  (*) location vendor specific and now determined from ACPI global tables
+
+2.3) APIC
+
+On Pentium and later processors, an on-board timer is available to each CPU
+as part of the Advanced Programmable Interrupt Controller.  The APIC is
+accessed through memory-mapped registers and provides interrupt service to each
+CPU, used for IPIs and local timer interrupts.
+
+Although in theory the APIC is a safe and stable source for local interrupts,
+in practice, many bugs and glitches have occurred due to the special nature of
+the APIC CPU-local memory-mapped hardware.  Beware that CPU errata may affect
+the use of the APIC and that workarounds may be required.  In addition, some of
+these workarounds pose unique constraints for virtualization - requiring either
+extra overhead incurred from extra reads of memory-mapped I/O or additional
+functionality that may be more computationally expensive to implement.
+
+Since the APIC is documented quite well in the Intel and AMD manuals, we will
+avoid repetition of the detail here.  It should be pointed out that the APIC
+timer is programmed through the LVT (local vector timer) register, is capable
+of one-shot or periodic operation, and is based on the bus clock divided down
+by the programmable divider register.
+
+2.4) HPET
+
+HPET is quite complex, and was originally intended to replace the PIT / RTC
+support of the X86 PC.  It remains to be seen whether that will be the case, as
+the de facto standard of PC hardware is to emulate these older devices.  Some
+systems designated as legacy free may support only the HPET as a hardware timer
+device.
+
+The HPET spec is rather loose and vague, requiring at least 3 hardware timers,
+but allowing implementation freedom to support many more.  It also imposes no
+fixed rate on the timer frequency, but does impose some extremal values on
+frequency, error and slew.
+
+In general, the HPET is recommended as a high precision (compared to PIT /RTC)
+time source which is independent of local variation (as there is only one HPET
+in any given system).  The HPET is also memory-mapped, and its presence is
+indicated through ACPI tables by the BIOS.
+
+Detailed specification of the HPET is beyond the current scope of this
+document, as it is also very well documented elsewhere.
+
+2.5) Offboard Timers
+
+Several cards, both proprietary (watchdog boards) and commonplace (e1000) have
+timing chips built into the cards which may have registers which are accessible
+to kernel or user drivers.  To the author's knowledge, using these to generate
+a clocksource for a Linux or other kernel has not yet been attempted and is in
+general frowned upon as not playing by the agreed rules of the game.  Such a
+timer device would require additional support to be virtualized properly and is
+not considered important at this time as no known operating system does this.
+
+=========================================================================
+
+3) TSC Hardware
+
+The TSC or time stamp counter is relatively simple in theory; it counts
+instruction cycles issued by the processor, which can be used as a measure of
+time.  In practice, due to a number of problems, it is the most complicated
+timekeeping device to use.
+
+The TSC is represented internally as a 64-bit MSR which can be read with the
+RDMSR, RDTSC, or RDTSCP (when available) instructions.  In the past, hardware
+limitations made it possible to write the TSC, but generally on old hardware it
+was only possible to write the low 32-bits of the 64-bit counter, and the upper
+32-bits of the counter were cleared.  Now, however, on Intel processors family
+0Fh, for models 3, 4 and 6, and family 06h, models e and f, this restriction
+has been lifted and all 64-bits are writable.  On AMD systems, the ability to
+write the TSC MSR is not an architectural guarantee.
+
+The TSC is accessible from CPL-0 and conditionally, for CPL > 0 software by
+means of the CR4.TSD bit, which when enabled, disables CPL > 0 TSC access.
+
+Some vendors have implemented an additional instruction, RDTSCP, which returns
+atomically not just the TSC, but an indicator which corresponds to the
+processor number.  This can be used to index into an array of TSC variables to
+determine offset information in SMP systems where TSCs are not synchronized.
+The presence of this instruction must be determined by consulting CPUID feature
+bits.
+
+Both VMX and SVM provide extension fields in the virtualization hardware which
+allows the guest visible TSC to be offset by a constant.  Newer implementations
+promise to allow the TSC to additionally be scaled, but this hardware is not
+yet widely available.
+
+3.1) TSC synchronization
+
+The TSC is a CPU-local clock in most implementations.  This means, on SMP
+platforms, the TSCs of different CPUs may start at different times depending
+on when the CPUs are powered on.  Generally, CPUs on the same die will share
+the same clock, however, this is not always the case.
+
+The BIOS may attempt to resynchronize the TSCs during the poweron process and
+the operating system or other system software may attempt to do this as well.
+Several hardware limitations make the problem worse - if it is not possible to
+write the full 64-bits of the TSC, it may be impossible to match the TSC in
+newly arriving CPUs to that of the rest of the system, resulting in
+unsynchronized TSCs.  This may be done by BIOS or system software, but in
+practice, getting a perfectly synchronized TSC will not be possible unless all
+values are read from the same clock, which generally only is possible on single
+socket systems or those with special hardware support.
+
+3.2) TSC and CPU hotplug
+
+As touched on already, CPUs which arrive later than the boot time of the system
+may not have a TSC value that is synchronized with the rest of the system.
+Either system software, BIOS, or SMM code may actually try to establish the TSC
+to a value matching the rest of the system, but a perfect match is usually not
+a guarantee.  This can have the effect of bringing a system from a state where
+TSC is synchronized back to a state where TSC synchronization flaws, however
+small, may be exposed to the OS and any virtualization environment.
+
+3.3) TSC and multi-socket / NUMA
+
+Multi-socket systems, especially large multi-socket systems are likely to have
+individual clocksources rather than a single, universally distributed clock.
+Since these clocks are driven by different crystals, they will not have
+perfectly matched frequency, and temperature and electrical variations will
+cause the CPU clocks, and thus the TSCs to drift over time.  Depending on the
+exact clock and bus design, the drift may or may not be fixed in absolute
+error, and may accumulate over time.
+
+In addition, very large systems may deliberately slew the clocks of individual
+cores.  This technique, known as spread-spectrum clocking, reduces EMI at the
+clock frequency and harmonics of it, which may be required to pass FCC
+standards for telecommunications and computer equipment.
+
+It is recommended not to trust the TSCs to remain synchronized on NUMA or
+multiple socket systems for these reasons.
+
+3.4) TSC and C-states
+
+C-states, or idling states of the processor, especially C1E and deeper sleep
+states may be problematic for TSC as well.  The TSC may stop advancing in such
+a state, resulting in a TSC which is behind that of other CPUs when execution
+is resumed.  Such CPUs must be detected and flagged by the operating system
+based on CPU and chipset identifications.
+
+The TSC in such a case may be corrected by catching it up to a known external
+clocksource.
+
+3.5) TSC frequency change / P-states
+
+To make things slightly more interesting, some CPUs may change frequency.  They
+may or may not run the TSC at the same rate, and because the frequency change
+may be staggered or slewed, at some points in time, the TSC rate may not be
+known other than falling within a range of values.  In this case, the TSC will
+not be a stable time source, and must be calibrated against a known, stable,
+external clock to be a usable source of time.
+
+Whether the TSC runs at a constant rate or scales with the P-state is model
+dependent and must be determined by inspecting CPUID, chipset or vendor
+specific MSR fields.
+
+In addition, some vendors have known bugs where the P-state is actually
+compensated for properly during normal operation, but when the processor is
+inactive, the P-state may be raised temporarily to service cache misses from
+other processors.  In such cases, the TSC on halted CPUs could advance faster
+than that of non-halted processors.  AMD Turion processors are known to have
+this problem.
+
+3.6) TSC and STPCLK / T-states
+
+External signals given to the processor may also have the effect of stopping
+the TSC.  This is typically done for thermal emergency power control to prevent
+an overheating condition, and typically, there is no way to detect that this
+condition has happened.
+
+3.7) TSC virtualization - VMX
+
+VMX provides conditional trapping of RDTSC, RDMSR, WRMSR and RDTSCP
+instructions, which is enough for full virtualization of TSC in any manner.  In
+addition, VMX allows passing through the host TSC plus an additional TSC_OFFSET
+field specified in the VMCS.  Special instructions must be used to read and
+write the VMCS field.
+
+3.8) TSC virtualization - SVM
+
+SVM provides conditional trapping of RDTSC, RDMSR, WRMSR and RDTSCP
+instructions, which is enough for full virtualization of TSC in any manner.  In
+addition, SVM allows passing through the host TSC plus an additional offset
+field specified in the SVM control block.
+
+3.9) TSC feature bits in Linux
+
+In summary, there is no way to guarantee the TSC remains in perfect
+synchronization unless it is explicitly guaranteed by the architecture.  Even
+if so, the TSCs in multi-sockets or NUMA systems may still run independently
+despite being locally consistent.
+
+The following feature bits are used by Linux to signal various TSC attributes,
+but they can only be taken to be meaningful for UP or single node systems.
+
+X86_FEATURE_TSC 		: The TSC is available in hardware
+X86_FEATURE_RDTSCP		: The RDTSCP instruction is available
+X86_FEATURE_CONSTANT_TSC 	: The TSC rate is unchanged with P-states
+X86_FEATURE_NONSTOP_TSC		: The TSC does not stop in C-states
+X86_FEATURE_TSC_RELIABLE	: TSC sync checks are skipped (VMware)
+
+4) Virtualization Problems
+
+Timekeeping is especially problematic for virtualization because a number of
+challenges arise.  The most obvious problem is that time is now shared between
+the host and, potentially, a number of virtual machines.  Thus the virtual
+operating system does not run with 100% usage of the CPU, despite the fact that
+it may very well make that assumption.  It may expect it to remain true to very
+exacting bounds when interrupt sources are disabled, but in reality only its
+virtual interrupt sources are disabled, and the machine may still be preempted
+at any time.  This causes problems as the passage of real time, the injection
+of machine interrupts and the associated clock sources are no longer completely
+synchronized with real time.
+
+This same problem can occur on native hardware to a degree, as SMM mode may
+steal cycles from the naturally on X86 systems when SMM mode is used by the
+BIOS, but not in such an extreme fashion.  However, the fact that SMM mode may
+cause similar problems to virtualization makes it a good justification for
+solving many of these problems on bare metal.
+
+4.1) Interrupt clocking
+
+One of the most immediate problems that occurs with legacy operating systems
+is that the system timekeeping routines are often designed to keep track of
+time by counting periodic interrupts.  These interrupts may come from the PIT
+or the RTC, but the problem is the same: the host virtualization engine may not
+be able to deliver the proper number of interrupts per second, and so guest
+time may fall behind.  This is especially problematic if a high interrupt rate
+is selected, such as 1000 HZ, which is unfortunately the default for many Linux
+guests.
+
+There are three approaches to solving this problem; first, it may be possible
+to simply ignore it.  Guests which have a separate time source for tracking
+'wall clock' or 'real time' may not need any adjustment of their interrupts to
+maintain proper time.  If this is not sufficient, it may be necessary to inject
+additional interrupts into the guest in order to increase the effective
+interrupt rate.  This approach leads to complications in extreme conditions,
+where host load or guest lag is too much to compensate for, and thus another
+solution to the problem has risen: the guest may need to become aware of lost
+ticks and compensate for them internally.  Although promising in theory, the
+implementation of this policy in Linux has been extremely error prone, and a
+number of buggy variants of lost tick compensation are distributed across
+commonly used Linux systems.
+
+Windows uses periodic RTC clocking as a means of keeping time internally, and
+thus requires interrupt slewing to keep proper time.  It does use a low enough
+rate (ed: is it 18.2 Hz?) however that it has not yet been a problem in
+practice.
+
+4.2) TSC sampling and serialization
+
+As the highest precision time source available, the cycle counter of the CPU
+has aroused much interest from developers.  As explained above, this timer has
+many problems unique to its nature as a local, potentially unstable and
+potentially unsynchronized source.  One issue which is not unique to the TSC,
+but is highlighted because of its very precise nature is sampling delay.  By
+definition, the counter, once read is already old.  However, it is also
+possible for the counter to be read ahead of the actual use of the result.
+This is a consequence of the superscalar execution of the instruction stream,
+which may execute instructions out of order.  Such execution is called
+non-serialized.  Forcing serialized execution is necessary for precise
+measurement with the TSC, and requires a serializing instruction, such as CPUID
+or an MSR read.
+
+Since CPUID may actually be virtualized by a trap and emulate mechanism, this
+serialization can pose a performance issue for hardware virtualization.  An
+accurate time stamp counter reading may therefore not always be available, and
+it may be necessary for an implementation to guard against "backwards" reads of
+the TSC as seen from other CPUs, even in an otherwise perfectly synchronized
+system.
+
+4.3) Timespec aliasing
+
+Additionally, this lack of serialization from the TSC poses another challenge
+when using results of the TSC when measured against another time source.  As
+the TSC is much higher precision, many possible values of the TSC may be read
+while another clock is still expressing the same value.
+
+That is, you may read (T,T+10) while external clock C maintains the same value.
+Due to non-serialized reads, you may actually end up with a range which
+fluctuates - from (T-1.. T+10).  Thus, any time calculated from a TSC, but
+calibrated against an external value may have a range of valid values.
+Re-calibrating this computation may actually cause time, as computed after the
+calibration, to go backwards, compared with time computed before the
+calibration.
+
+This problem is particularly pronounced with an internal time source in Linux,
+the kernel time, which is expressed in the theoretically high resolution
+timespec - but which advances in much larger granularity intervals, sometimes
+at the rate of jiffies, and possibly in catchup modes, at a much larger step.
+
+This aliasing requires care in the computation and recalibration of kvmclock
+and any other values derived from TSC computation (such as TSC virtualization
+itself).
+
+4.4) Migration
+
+Migration of a virtual machine raises problems for timekeeping in two ways.
+First, the migration itself may take time, during which interrupts cannot be
+delivered, and after which, the guest time may need to be caught up.  NTP may
+be able to help to some degree here, as the clock correction required is
+typically small enough to fall in the NTP-correctable window.
+
+An additional concern is that timers based off the TSC (or HPET, if the raw bus
+clock is exposed) may now be running at different rates, requiring compensation
+in some way in the hypervisor by virtualizing these timers.  In addition,
+migrating to a faster machine may preclude the use of a passthrough TSC, as a
+faster clock cannot be made visible to a guest without the potential of time
+advancing faster than usual.  A slower clock is less of a problem, as it can
+always be caught up to the original rate.  KVM clock avoids these problems by
+simply storing multipliers and offsets against the TSC for the guest to convert
+back into nanosecond resolution values.
+
+4.5) Scheduling
+
+Since scheduling may be based on precise timing and firing of interrupts, the
+scheduling algorithms of an operating system may be adversely affected by
+virtualization.  In theory, the effect is random and should be universally
+distributed, but in contrived as well as real scenarios (guest device access,
+causes of virtualization exits, possible context switch), this may not always
+be the case.  The effect of this has not been well studied.
+
+In an attempt to work around this, several implementations have provided a
+paravirtualized scheduler clock, which reveals the true amount of CPU time for
+which a virtual machine has been running.
+
+4.6) Watchdogs
+
+Watchdog timers, such as the lock detector in Linux may fire accidentally when
+running under hardware virtualization due to timer interrupts being delayed or
+misinterpretation of the passage of real time.  Usually, these warnings are
+spurious and can be ignored, but in some circumstances it may be necessary to
+disable such detection.
+
+4.7) Delays and precision timing
+
+Precise timing and delays may not be possible in a virtualized system.  This
+can happen if the system is controlling physical hardware, or issues delays to
+compensate for slower I/O to and from devices.  The first issue is not solvable
+in general for a virtualized system; hardware control software can't be
+adequately virtualized without a full real-time operating system, which would
+require an RT aware virtualization platform.
+
+The second issue may cause performance problems, but this is unlikely to be a
+significant issue.  In many cases these delays may be eliminated through
+configuration or paravirtualization.
+
+4.8) Covert channels and leaks
+
+In addition to the above problems, time information will inevitably leak to the
+guest about the host in anything but a perfect implementation of virtualized
+time.  This may allow the guest to infer the presence of a hypervisor (as in a
+red-pill type detection), and it may allow information to leak between guests
+by using CPU utilization itself as a signalling channel.  Preventing such
+problems would require completely isolated virtual time which may not track
+real time any longer.  This may be useful in certain security or QA contexts,
+but in general isn't recommended for real-world deployment scenarios.
diff --git a/Documentation/virtual/kvm/vcpu-requests.rst b/Documentation/virtual/kvm/vcpu-requests.rst
new file mode 100644
index 0000000..5feb370
--- /dev/null
+++ b/Documentation/virtual/kvm/vcpu-requests.rst
@@ -0,0 +1,307 @@
+=================
+KVM VCPU Requests
+=================
+
+Overview
+========
+
+KVM supports an internal API enabling threads to request a VCPU thread to
+perform some activity.  For example, a thread may request a VCPU to flush
+its TLB with a VCPU request.  The API consists of the following functions::
+
+  /* Check if any requests are pending for VCPU @vcpu. */
+  bool kvm_request_pending(struct kvm_vcpu *vcpu);
+
+  /* Check if VCPU @vcpu has request @req pending. */
+  bool kvm_test_request(int req, struct kvm_vcpu *vcpu);
+
+  /* Clear request @req for VCPU @vcpu. */
+  void kvm_clear_request(int req, struct kvm_vcpu *vcpu);
+
+  /*
+   * Check if VCPU @vcpu has request @req pending. When the request is
+   * pending it will be cleared and a memory barrier, which pairs with
+   * another in kvm_make_request(), will be issued.
+   */
+  bool kvm_check_request(int req, struct kvm_vcpu *vcpu);
+
+  /*
+   * Make request @req of VCPU @vcpu. Issues a memory barrier, which pairs
+   * with another in kvm_check_request(), prior to setting the request.
+   */
+  void kvm_make_request(int req, struct kvm_vcpu *vcpu);
+
+  /* Make request @req of all VCPUs of the VM with struct kvm @kvm. */
+  bool kvm_make_all_cpus_request(struct kvm *kvm, unsigned int req);
+
+Typically a requester wants the VCPU to perform the activity as soon
+as possible after making the request.  This means most requests
+(kvm_make_request() calls) are followed by a call to kvm_vcpu_kick(),
+and kvm_make_all_cpus_request() has the kicking of all VCPUs built
+into it.
+
+VCPU Kicks
+----------
+
+The goal of a VCPU kick is to bring a VCPU thread out of guest mode in
+order to perform some KVM maintenance.  To do so, an IPI is sent, forcing
+a guest mode exit.  However, a VCPU thread may not be in guest mode at the
+time of the kick.  Therefore, depending on the mode and state of the VCPU
+thread, there are two other actions a kick may take.  All three actions
+are listed below:
+
+1) Send an IPI.  This forces a guest mode exit.
+2) Waking a sleeping VCPU.  Sleeping VCPUs are VCPU threads outside guest
+   mode that wait on waitqueues.  Waking them removes the threads from
+   the waitqueues, allowing the threads to run again.  This behavior
+   may be suppressed, see KVM_REQUEST_NO_WAKEUP below.
+3) Nothing.  When the VCPU is not in guest mode and the VCPU thread is not
+   sleeping, then there is nothing to do.
+
+VCPU Mode
+---------
+
+VCPUs have a mode state, ``vcpu->mode``, that is used to track whether the
+guest is running in guest mode or not, as well as some specific
+outside guest mode states.  The architecture may use ``vcpu->mode`` to
+ensure VCPU requests are seen by VCPUs (see "Ensuring Requests Are Seen"),
+as well as to avoid sending unnecessary IPIs (see "IPI Reduction"), and
+even to ensure IPI acknowledgements are waited upon (see "Waiting for
+Acknowledgements").  The following modes are defined:
+
+OUTSIDE_GUEST_MODE
+
+  The VCPU thread is outside guest mode.
+
+IN_GUEST_MODE
+
+  The VCPU thread is in guest mode.
+
+EXITING_GUEST_MODE
+
+  The VCPU thread is transitioning from IN_GUEST_MODE to
+  OUTSIDE_GUEST_MODE.
+
+READING_SHADOW_PAGE_TABLES
+
+  The VCPU thread is outside guest mode, but it wants the sender of
+  certain VCPU requests, namely KVM_REQ_TLB_FLUSH, to wait until the VCPU
+  thread is done reading the page tables.
+
+VCPU Request Internals
+======================
+
+VCPU requests are simply bit indices of the ``vcpu->requests`` bitmap.
+This means general bitops, like those documented in [atomic-ops]_ could
+also be used, e.g. ::
+
+  clear_bit(KVM_REQ_UNHALT & KVM_REQUEST_MASK, &vcpu->requests);
+
+However, VCPU request users should refrain from doing so, as it would
+break the abstraction.  The first 8 bits are reserved for architecture
+independent requests, all additional bits are available for architecture
+dependent requests.
+
+Architecture Independent Requests
+---------------------------------
+
+KVM_REQ_TLB_FLUSH
+
+  KVM's common MMU notifier may need to flush all of a guest's TLB
+  entries, calling kvm_flush_remote_tlbs() to do so.  Architectures that
+  choose to use the common kvm_flush_remote_tlbs() implementation will
+  need to handle this VCPU request.
+
+KVM_REQ_MMU_RELOAD
+
+  When shadow page tables are used and memory slots are removed it's
+  necessary to inform each VCPU to completely refresh the tables.  This
+  request is used for that.
+
+KVM_REQ_PENDING_TIMER
+
+  This request may be made from a timer handler run on the host on behalf
+  of a VCPU.  It informs the VCPU thread to inject a timer interrupt.
+
+KVM_REQ_UNHALT
+
+  This request may be made from the KVM common function kvm_vcpu_block(),
+  which is used to emulate an instruction that causes a CPU to halt until
+  one of an architectural specific set of events and/or interrupts is
+  received (determined by checking kvm_arch_vcpu_runnable()).  When that
+  event or interrupt arrives kvm_vcpu_block() makes the request.  This is
+  in contrast to when kvm_vcpu_block() returns due to any other reason,
+  such as a pending signal, which does not indicate the VCPU's halt
+  emulation should stop, and therefore does not make the request.
+
+KVM_REQUEST_MASK
+----------------
+
+VCPU requests should be masked by KVM_REQUEST_MASK before using them with
+bitops.  This is because only the lower 8 bits are used to represent the
+request's number.  The upper bits are used as flags.  Currently only two
+flags are defined.
+
+VCPU Request Flags
+------------------
+
+KVM_REQUEST_NO_WAKEUP
+
+  This flag is applied to requests that only need immediate attention
+  from VCPUs running in guest mode.  That is, sleeping VCPUs do not need
+  to be awaken for these requests.  Sleeping VCPUs will handle the
+  requests when they are awaken later for some other reason.
+
+KVM_REQUEST_WAIT
+
+  When requests with this flag are made with kvm_make_all_cpus_request(),
+  then the caller will wait for each VCPU to acknowledge its IPI before
+  proceeding.  This flag only applies to VCPUs that would receive IPIs.
+  If, for example, the VCPU is sleeping, so no IPI is necessary, then
+  the requesting thread does not wait.  This means that this flag may be
+  safely combined with KVM_REQUEST_NO_WAKEUP.  See "Waiting for
+  Acknowledgements" for more information about requests with
+  KVM_REQUEST_WAIT.
+
+VCPU Requests with Associated State
+===================================
+
+Requesters that want the receiving VCPU to handle new state need to ensure
+the newly written state is observable to the receiving VCPU thread's CPU
+by the time it observes the request.  This means a write memory barrier
+must be inserted after writing the new state and before setting the VCPU
+request bit.  Additionally, on the receiving VCPU thread's side, a
+corresponding read barrier must be inserted after reading the request bit
+and before proceeding to read the new state associated with it.  See
+scenario 3, Message and Flag, of [lwn-mb]_ and the kernel documentation
+[memory-barriers]_.
+
+The pair of functions, kvm_check_request() and kvm_make_request(), provide
+the memory barriers, allowing this requirement to be handled internally by
+the API.
+
+Ensuring Requests Are Seen
+==========================
+
+When making requests to VCPUs, we want to avoid the receiving VCPU
+executing in guest mode for an arbitrary long time without handling the
+request.  We can be sure this won't happen as long as we ensure the VCPU
+thread checks kvm_request_pending() before entering guest mode and that a
+kick will send an IPI to force an exit from guest mode when necessary.
+Extra care must be taken to cover the period after the VCPU thread's last
+kvm_request_pending() check and before it has entered guest mode, as kick
+IPIs will only trigger guest mode exits for VCPU threads that are in guest
+mode or at least have already disabled interrupts in order to prepare to
+enter guest mode.  This means that an optimized implementation (see "IPI
+Reduction") must be certain when it's safe to not send the IPI.  One
+solution, which all architectures except s390 apply, is to:
+
+- set ``vcpu->mode`` to IN_GUEST_MODE between disabling the interrupts and
+  the last kvm_request_pending() check;
+- enable interrupts atomically when entering the guest.
+
+This solution also requires memory barriers to be placed carefully in both
+the requesting thread and the receiving VCPU.  With the memory barriers we
+can exclude the possibility of a VCPU thread observing
+!kvm_request_pending() on its last check and then not receiving an IPI for
+the next request made of it, even if the request is made immediately after
+the check.  This is done by way of the Dekker memory barrier pattern
+(scenario 10 of [lwn-mb]_).  As the Dekker pattern requires two variables,
+this solution pairs ``vcpu->mode`` with ``vcpu->requests``.  Substituting
+them into the pattern gives::
+
+  CPU1                                    CPU2
+  =================                       =================
+  local_irq_disable();
+  WRITE_ONCE(vcpu->mode, IN_GUEST_MODE);  kvm_make_request(REQ, vcpu);
+  smp_mb();                               smp_mb();
+  if (kvm_request_pending(vcpu)) {        if (READ_ONCE(vcpu->mode) ==
+                                              IN_GUEST_MODE) {
+      ...abort guest entry...                 ...send IPI...
+  }                                       }
+
+As stated above, the IPI is only useful for VCPU threads in guest mode or
+that have already disabled interrupts.  This is why this specific case of
+the Dekker pattern has been extended to disable interrupts before setting
+``vcpu->mode`` to IN_GUEST_MODE.  WRITE_ONCE() and READ_ONCE() are used to
+pedantically implement the memory barrier pattern, guaranteeing the
+compiler doesn't interfere with ``vcpu->mode``'s carefully planned
+accesses.
+
+IPI Reduction
+-------------
+
+As only one IPI is needed to get a VCPU to check for any/all requests,
+then they may be coalesced.  This is easily done by having the first IPI
+sending kick also change the VCPU mode to something !IN_GUEST_MODE.  The
+transitional state, EXITING_GUEST_MODE, is used for this purpose.
+
+Waiting for Acknowledgements
+----------------------------
+
+Some requests, those with the KVM_REQUEST_WAIT flag set, require IPIs to
+be sent, and the acknowledgements to be waited upon, even when the target
+VCPU threads are in modes other than IN_GUEST_MODE.  For example, one case
+is when a target VCPU thread is in READING_SHADOW_PAGE_TABLES mode, which
+is set after disabling interrupts.  To support these cases, the
+KVM_REQUEST_WAIT flag changes the condition for sending an IPI from
+checking that the VCPU is IN_GUEST_MODE to checking that it is not
+OUTSIDE_GUEST_MODE.
+
+Request-less VCPU Kicks
+-----------------------
+
+As the determination of whether or not to send an IPI depends on the
+two-variable Dekker memory barrier pattern, then it's clear that
+request-less VCPU kicks are almost never correct.  Without the assurance
+that a non-IPI generating kick will still result in an action by the
+receiving VCPU, as the final kvm_request_pending() check does for
+request-accompanying kicks, then the kick may not do anything useful at
+all.  If, for instance, a request-less kick was made to a VCPU that was
+just about to set its mode to IN_GUEST_MODE, meaning no IPI is sent, then
+the VCPU thread may continue its entry without actually having done
+whatever it was the kick was meant to initiate.
+
+One exception is x86's posted interrupt mechanism.  In this case, however,
+even the request-less VCPU kick is coupled with the same
+local_irq_disable() + smp_mb() pattern described above; the ON bit
+(Outstanding Notification) in the posted interrupt descriptor takes the
+role of ``vcpu->requests``.  When sending a posted interrupt, PIR.ON is
+set before reading ``vcpu->mode``; dually, in the VCPU thread,
+vmx_sync_pir_to_irr() reads PIR after setting ``vcpu->mode`` to
+IN_GUEST_MODE.
+
+Additional Considerations
+=========================
+
+Sleeping VCPUs
+--------------
+
+VCPU threads may need to consider requests before and/or after calling
+functions that may put them to sleep, e.g. kvm_vcpu_block().  Whether they
+do or not, and, if they do, which requests need consideration, is
+architecture dependent.  kvm_vcpu_block() calls kvm_arch_vcpu_runnable()
+to check if it should awaken.  One reason to do so is to provide
+architectures a function where requests may be checked if necessary.
+
+Clearing Requests
+-----------------
+
+Generally it only makes sense for the receiving VCPU thread to clear a
+request.  However, in some circumstances, such as when the requesting
+thread and the receiving VCPU thread are executed serially, such as when
+they are the same thread, or when they are using some form of concurrency
+control to temporarily execute synchronously, then it's possible to know
+that the request may be cleared immediately, rather than waiting for the
+receiving VCPU thread to handle the request in VCPU RUN.  The only current
+examples of this are kvm_vcpu_block() calls made by VCPUs to block
+themselves.  A possible side-effect of that call is to make the
+KVM_REQ_UNHALT request, which may then be cleared immediately when the
+VCPU returns from the call.
+
+References
+==========
+
+.. [atomic-ops] Documentation/core-api/atomic_ops.rst
+.. [memory-barriers] Documentation/memory-barriers.txt
+.. [lwn-mb] https://lwn.net/Articles/573436/
diff --git a/Documentation/virtual/paravirt_ops.txt b/Documentation/virtual/paravirt_ops.txt
new file mode 100644
index 0000000..d4881c0
--- /dev/null
+++ b/Documentation/virtual/paravirt_ops.txt
@@ -0,0 +1,32 @@
+Paravirt_ops
+============
+
+Linux provides support for different hypervisor virtualization technologies.
+Historically different binary kernels would be required in order to support
+different hypervisors, this restriction was removed with pv_ops.
+Linux pv_ops is a virtualization API which enables support for different
+hypervisors. It allows each hypervisor to override critical operations and
+allows a single kernel binary to run on all supported execution environments
+including native machine -- without any hypervisors.
+
+pv_ops provides a set of function pointers which represent operations
+corresponding to low level critical instructions and high level
+functionalities in various areas. pv-ops allows for optimizations at run
+time by enabling binary patching of the low-ops critical operations
+at boot time.
+
+pv_ops operations are classified into three categories:
+
+- simple indirect call
+  These operations correspond to high level functionality where it is
+  known that the overhead of indirect call isn't very important.
+
+- indirect call which allows optimization with binary patch
+  Usually these operations correspond to low level critical instructions. They
+  are called frequently and are performance critical. The overhead is
+  very important.
+
+- a set of macros for hand written assembly code
+  Hand written assembly codes (.S files) also need paravirtualization
+  because they include sensitive instructions or some of code paths in
+  them are very performance critical.
diff --git a/Documentation/virtual/uml/UserModeLinux-HOWTO.txt b/Documentation/virtual/uml/UserModeLinux-HOWTO.txt
new file mode 100644
index 0000000..87b80f5
--- /dev/null
+++ b/Documentation/virtual/uml/UserModeLinux-HOWTO.txt
@@ -0,0 +1,4589 @@
+  User Mode Linux HOWTO
+  User Mode Linux Core Team
+  Mon Nov 18 14:16:16 EST 2002
+
+  This document describes the use and abuse of Jeff Dike's User Mode
+  Linux: a port of the Linux kernel as a normal Intel Linux process.
+  ______________________________________________________________________
+
+  Table of Contents
+
+  1. Introduction
+
+     1.1 How is User Mode Linux Different?
+     1.2 Why Would I Want User Mode Linux?
+
+  2. Compiling the kernel and modules
+
+     2.1 Compiling the kernel
+     2.2 Compiling and installing kernel modules
+     2.3 Compiling and installing uml_utilities
+
+  3. Running UML and logging in
+
+     3.1 Running UML
+     3.2 Logging in
+     3.3 Examples
+
+  4. UML on 2G/2G hosts
+
+     4.1 Introduction
+     4.2 The problem
+     4.3 The solution
+
+  5. Setting up serial lines and consoles
+
+     5.1 Specifying the device
+     5.2 Specifying the channel
+     5.3 Examples
+
+  6. Setting up the network
+
+     6.1 General setup
+     6.2 Userspace daemons
+     6.3 Specifying ethernet addresses
+     6.4 UML interface setup
+     6.5 Multicast
+     6.6 TUN/TAP with the uml_net helper
+     6.7 TUN/TAP with a preconfigured tap device
+     6.8 Ethertap
+     6.9 The switch daemon
+     6.10 Slip
+     6.11 Slirp
+     6.12 pcap
+     6.13 Setting up the host yourself
+
+  7. Sharing Filesystems between Virtual Machines
+
+     7.1 A warning
+     7.2 Using layered block devices
+     7.3 Note!
+     7.4 Another warning
+     7.5 uml_moo : Merging a COW file with its backing file
+
+  8. Creating filesystems
+
+     8.1 Create the filesystem file
+     8.2 Assign the file to a UML device
+     8.3 Creating and mounting the filesystem
+
+  9. Host file access
+
+     9.1 Using hostfs
+     9.2 hostfs as the root filesystem
+     9.3 Building hostfs
+
+  10. The Management Console
+     10.1 version
+     10.2 halt and reboot
+     10.3 config
+     10.4 remove
+     10.5 sysrq
+     10.6 help
+     10.7 cad
+     10.8 stop
+     10.9 go
+
+  11. Kernel debugging
+
+     11.1 Starting the kernel under gdb
+     11.2 Examining sleeping processes
+     11.3 Running ddd on UML
+     11.4 Debugging modules
+     11.5 Attaching gdb to the kernel
+     11.6 Using alternate debuggers
+
+  12. Kernel debugging examples
+
+     12.1 The case of the hung fsck
+     12.2 Episode 2: The case of the hung fsck
+
+  13. What to do when UML doesn't work
+
+     13.1 Strange compilation errors when you build from source
+     13.2 (obsolete)
+     13.3 A variety of panics and hangs with /tmp on a reiserfs  filesystem
+     13.4 The compile fails with errors about conflicting types for 'open', 'dup', and 'waitpid'
+     13.5 UML doesn't work when /tmp is an NFS filesystem
+     13.6 UML hangs on boot when compiled with gprof support
+     13.7 syslogd dies with a SIGTERM on startup
+     13.8 TUN/TAP networking doesn't work on a 2.4 host
+     13.9 You can network to the host but not to other machines on the net
+     13.10 I have no root and I want to scream
+     13.11 UML build conflict between ptrace.h and ucontext.h
+     13.12 The UML BogoMips is exactly half the host's BogoMips
+     13.13 When you run UML, it immediately segfaults
+     13.14 xterms appear, then immediately disappear
+     13.15 Any other panic, hang, or strange behavior
+
+  14. Diagnosing Problems
+
+     14.1 Case 1 : Normal kernel panics
+     14.2 Case 2 : Tracing thread panics
+     14.3 Case 3 : Tracing thread panics caused by other threads
+     14.4 Case 4 : Hangs
+
+  15. Thanks
+
+     15.1 Code and Documentation
+     15.2 Flushing out bugs
+     15.3 Buglets and clean-ups
+     15.4 Case Studies
+     15.5 Other contributions
+
+
+  ______________________________________________________________________
+
+  1.  Introduction
+
+  Welcome to User Mode Linux.  It's going to be fun.
+
+
+
+  1.1.  How is User Mode Linux Different?
+
+  Normally, the Linux Kernel talks straight to your hardware (video
+  card, keyboard, hard drives, etc), and any programs which run ask the
+  kernel to operate the hardware, like so:
+
+
+
+         +-----------+-----------+----+
+         | Process 1 | Process 2 | ...|
+         +-----------+-----------+----+
+         |       Linux Kernel         |
+         +----------------------------+
+         |         Hardware           |
+         +----------------------------+
+
+
+
+
+  The User Mode Linux Kernel is different; instead of talking to the
+  hardware, it talks to a `real' Linux kernel (called the `host kernel'
+  from now on), like any other program.  Programs can then run inside
+  User-Mode Linux as if they were running under a normal kernel, like
+  so:
+
+
+
+                     +----------------+
+                     | Process 2 | ...|
+         +-----------+----------------+
+         | Process 1 | User-Mode Linux|
+         +----------------------------+
+         |       Linux Kernel         |
+         +----------------------------+
+         |         Hardware           |
+         +----------------------------+
+
+
+
+
+
+  1.2.  Why Would I Want User Mode Linux?
+
+
+  1. If User Mode Linux crashes, your host kernel is still fine.
+
+  2. You can run a usermode kernel as a non-root user.
+
+  3. You can debug the User Mode Linux like any normal process.
+
+  4. You can run gprof (profiling) and gcov (coverage testing).
+
+  5. You can play with your kernel without breaking things.
+
+  6. You can use it as a sandbox for testing new apps.
+
+  7. You can try new development kernels safely.
+
+  8. You can run different distributions simultaneously.
+
+  9. It's extremely fun.
+
+
+
+
+
+  2.  Compiling the kernel and modules
+
+
+
+
+  2.1.  Compiling the kernel
+
+
+  Compiling the user mode kernel is just like compiling any other
+  kernel.  Let's go through the steps, using 2.4.0-prerelease (current
+  as of this writing) as an example:
+
+
+  1. Download the latest UML patch from
+
+     the download page <http://user-mode-linux.sourceforge.net/
+
+     In this example, the file is uml-patch-2.4.0-prerelease.bz2.
+
+
+  2. Download the matching kernel from your favourite kernel mirror,
+     such as:
+
+     ftp://ftp.ca.kernel.org/pub/kernel/v2.4/linux-2.4.0-prerelease.tar.bz2
+     <ftp://ftp.ca.kernel.org/pub/kernel/v2.4/linux-2.4.0-prerelease.tar.bz2>
+     .
+
+
+  3. Make a directory and unpack the kernel into it.
+
+
+
+       host%
+       mkdir ~/uml
+
+
+
+
+
+
+       host%
+       cd ~/uml
+
+
+
+
+
+
+       host%
+       tar -xzvf linux-2.4.0-prerelease.tar.bz2
+
+
+
+
+
+
+  4. Apply the patch using
+
+
+
+       host%
+       cd ~/uml/linux
+
+
+
+       host%
+       bzcat uml-patch-2.4.0-prerelease.bz2 | patch -p1
+
+
+
+
+
+
+  5. Run your favorite config; `make xconfig ARCH=um' is the most
+     convenient.  `make config ARCH=um' and 'make menuconfig ARCH=um'
+     will work as well.  The defaults will give you a useful kernel.  If
+     you want to change something, go ahead, it probably won't hurt
+     anything.
+
+
+     Note:  If the host is configured with a 2G/2G address space split
+     rather than the usual 3G/1G split, then the packaged UML binaries
+     will not run.  They will immediately segfault.  See ``UML on 2G/2G
+     hosts''  for the scoop on running UML on your system.
+
+
+
+  6. Finish with `make linux ARCH=um': the result is a file called
+     `linux' in the top directory of your source tree.
+
+  Make sure that you don't build this kernel in /usr/src/linux.  On some
+  distributions, /usr/include/asm is a link into this pool.  The user-
+  mode build changes the other end of that link, and things that include
+  <asm/anything.h> stop compiling.
+
+  The sources are also available from cvs at the project's cvs page,
+  which has directions on getting the sources. You can also browse the
+  CVS pool from there.
+
+  If you get the CVS sources, you will have to check them out into an
+  empty directory. You will then have to copy each file into the
+  corresponding directory in the appropriate kernel pool.
+
+  If you don't have the latest kernel pool, you can get the
+  corresponding user-mode sources with
+
+
+       host% cvs co -r v_2_3_x linux
+
+
+
+
+  where 'x' is the version in your pool. Note that you will not get the
+  bug fixes and enhancements that have gone into subsequent releases.
+
+
+  2.2.  Compiling and installing kernel modules
+
+  UML modules are built in the same way as the native kernel (with the
+  exception of the 'ARCH=um' that you always need for UML):
+
+
+       host% make modules ARCH=um
+
+
+
+
+  Any modules that you want to load into this kernel need to be built in
+  the user-mode pool.  Modules from the native kernel won't work.
+
+  You can install them by using ftp or something to copy them into the
+  virtual machine and dropping them into /lib/modules/`uname -r`.
+
+  You can also get the kernel build process to install them as follows:
+
+  1. with the kernel not booted, mount the root filesystem in the top
+     level of the kernel pool:
+
+
+       host% mount root_fs mnt -o loop
+
+
+
+
+
+
+  2. run
+
+
+       host%
+       make modules_install INSTALL_MOD_PATH=`pwd`/mnt ARCH=um
+
+
+
+
+
+
+  3. unmount the filesystem
+
+
+       host% umount mnt
+
+
+
+
+
+
+  4. boot the kernel on it
+
+
+  When the system is booted, you can use insmod as usual to get the
+  modules into the kernel.  A number of things have been loaded into UML
+  as modules, especially filesystems and network protocols and filters,
+  so most symbols which need to be exported probably already are.
+  However, if you do find symbols that need exporting, let  us
+  <http://user-mode-linux.sourceforge.net/>  know, and
+  they'll be "taken care of".
+
+
+
+  2.3.  Compiling and installing uml_utilities
+
+  Many features of the UML kernel require a user-space helper program,
+  so a uml_utilities package is distributed separately from the kernel
+  patch which provides these helpers. Included within this is:
+
+  o  port-helper - Used by consoles which connect to xterms or ports
+
+  o  tunctl - Configuration tool to create and delete tap devices
+
+  o  uml_net - Setuid binary for automatic tap device configuration
+
+  o  uml_switch - User-space virtual switch required for daemon
+     transport
+
+     The uml_utilities tree is compiled with:
+
+
+       host#
+       make && make install
+
+
+
+
+  Note that UML kernel patches may require a specific version of the
+  uml_utilities distribution. If you don't keep up with the mailing
+  lists, ensure that you have the latest release of uml_utilities if you
+  are experiencing problems with your UML kernel, particularly when
+  dealing with consoles or command-line switches to the helper programs
+
+
+
+
+
+
+
+
+  3.  Running UML and logging in
+
+
+
+  3.1.  Running UML
+
+  It runs on 2.2.15 or later, and all 2.4 kernels.
+
+
+  Booting UML is straightforward.  Simply run 'linux': it will try to
+  mount the file `root_fs' in the current directory.  You do not need to
+  run it as root.  If your root filesystem is not named `root_fs', then
+  you need to put a `ubd0=root_fs_whatever' switch on the linux command
+  line.
+
+
+  You will need a filesystem to boot UML from.  There are a number
+  available for download from  here  <http://user-mode-
+  linux.sourceforge.net/> .  There are also  several tools
+  <http://user-mode-linux.sourceforge.net/>  which can be
+  used to generate UML-compatible filesystem images from media.
+  The kernel will boot up and present you with a login prompt.
+
+
+  Note:  If the host is configured with a 2G/2G address space split
+  rather than the usual 3G/1G split, then the packaged UML binaries will
+  not run.  They will immediately segfault.  See ``UML on 2G/2G hosts''
+  for the scoop on running UML on your system.
+
+
+
+  3.2.  Logging in
+
+
+
+  The prepackaged filesystems have a root account with password 'root'
+  and a user account with password 'user'.  The login banner will
+  generally tell you how to log in.  So, you log in and you will find
+  yourself inside a little virtual machine. Our filesystems have a
+  variety of commands and utilities installed (and it is fairly easy to
+  add more), so you will have a lot of tools with which to poke around
+  the system.
+
+  There are a couple of other ways to log in:
+
+  o  On a virtual console
+
+
+
+     Each virtual console that is configured (i.e. the device exists in
+     /dev and /etc/inittab runs a getty on it) will come up in its own
+     xterm.  If you get tired of the xterms, read ``Setting up serial
+     lines and consoles''  to see how to attach the consoles to
+     something else, like host ptys.
+
+
+
+  o  Over the serial line
+
+
+     In the boot output, find a line that looks like:
+
+
+
+       serial line 0 assigned pty /dev/ptyp1
+
+
+
+
+  Attach your favorite terminal program to the corresponding tty.  I.e.
+  for minicom, the command would be
+
+
+       host% minicom -o -p /dev/ttyp1
+
+
+
+
+
+
+  o  Over the net
+
+
+     If the network is running, then you can telnet to the virtual
+     machine and log in to it.  See ``Setting up the network''  to learn
+     about setting up a virtual network.
+
+  When you're done using it, run halt, and the kernel will bring itself
+  down and the process will exit.
+
+
+  3.3.  Examples
+
+  Here are some examples of UML in action:
+
+  o  A login session <http://user-mode-linux.sourceforge.net/login.html>
+
+  o  A virtual network <http://user-mode-linux.sourceforge.net/net.html>
+
+
+
+
+
+
+
+  4.  UML on 2G/2G hosts
+
+
+
+
+  4.1.  Introduction
+
+
+  Most Linux machines are configured so that the kernel occupies the
+  upper 1G (0xc0000000 - 0xffffffff) of the 4G address space and
+  processes use the lower 3G (0x00000000 - 0xbfffffff).  However, some
+  machine are configured with a 2G/2G split, with the kernel occupying
+  the upper 2G (0x80000000 - 0xffffffff) and processes using the lower
+  2G (0x00000000 - 0x7fffffff).
+
+
+
+
+  4.2.  The problem
+
+
+  The prebuilt UML binaries on this site will not run on 2G/2G hosts
+  because UML occupies the upper .5G of the 3G process address space
+  (0xa0000000 - 0xbfffffff).  Obviously, on 2G/2G hosts, this is right
+  in the middle of the kernel address space, so UML won't even load - it
+  will immediately segfault.
+
+
+
+
+  4.3.  The solution
+
+
+  The fix for this is to rebuild UML from source after enabling
+  CONFIG_HOST_2G_2G (under 'General Setup').  This will cause UML to
+  load itself in the top .5G of that smaller process address space,
+  where it will run fine.  See ``Compiling the kernel and modules''  if
+  you need help building UML from source.
+
+
+
+
+
+
+
+
+
+
+  5.  Setting up serial lines and consoles
+
+
+  It is possible to attach UML serial lines and consoles to many types
+  of host I/O channels by specifying them on the command line.
+
+
+  You can attach them to host ptys, ttys, file descriptors, and ports.
+  This allows you to do things like
+
+  o  have a UML console appear on an unused host console,
+
+  o  hook two virtual machines together by having one attach to a pty
+     and having the other attach to the corresponding tty
+
+  o  make a virtual machine accessible from the net by attaching a
+     console to a port on the host.
+
+
+  The general format of the command line option is device=channel.
+
+
+
+  5.1.  Specifying the device
+
+  Devices are specified with "con" or "ssl" (console or serial line,
+  respectively), optionally with a device number if you are talking
+  about a specific device.
+
+
+  Using just "con" or "ssl" describes all of the consoles or serial
+  lines.  If you want to talk about console #3 or serial line #10, they
+  would be "con3" and "ssl10", respectively.
+
+
+  A specific device name will override a less general "con=" or "ssl=".
+  So, for example, you can assign a pty to each of the serial lines
+  except for the first two like this:
+
+
+        ssl=pty ssl0=tty:/dev/tty0 ssl1=tty:/dev/tty1
+
+
+
+
+  The specificity of the device name is all that matters; order on the
+  command line is irrelevant.
+
+
+
+  5.2.  Specifying the channel
+
+  There are a number of different types of channels to attach a UML
+  device to, each with a different way of specifying exactly what to
+  attach to.
+
+  o  pseudo-terminals - device=pty pts terminals - device=pts
+
+
+     This will cause UML to allocate a free host pseudo-terminal for the
+     device.  The terminal that it got will be announced in the boot
+     log.  You access it by attaching a terminal program to the
+     corresponding tty:
+
+  o  screen /dev/pts/n
+
+  o  screen /dev/ttyxx
+
+  o  minicom -o -p /dev/ttyxx - minicom seems not able to handle pts
+     devices
+
+  o  kermit - start it up, 'open' the device, then 'connect'
+
+
+
+
+
+  o  terminals - device=tty:tty device file
+
+
+     This will make UML attach the device to the specified tty (i.e
+
+
+        con1=tty:/dev/tty3
+
+
+
+
+  will attach UML's console 1 to the host's /dev/tty3).  If the tty that
+  you specify is the slave end of a tty/pty pair, something else must
+  have already opened the corresponding pty in order for this to work.
+
+
+
+
+
+  o  xterms - device=xterm
+
+
+     UML will run an xterm and the device will be attached to it.
+
+
+
+
+
+  o  Port - device=port:port number
+
+
+     This will attach the UML devices to the specified host port.
+     Attaching console 1 to the host's port 9000 would be done like
+     this:
+
+
+        con1=port:9000
+
+
+
+
+  Attaching all the serial lines to that port would be done similarly:
+
+
+        ssl=port:9000
+
+
+
+
+  You access these devices by telnetting to that port.  Each active tel-
+  net session gets a different device.  If there are more telnets to a
+  port than UML devices attached to it, then the extra telnet sessions
+  will block until an existing telnet detaches, or until another device
+  becomes active (i.e. by being activated in /etc/inittab).
+
+  This channel has the advantage that you can both attach multiple UML
+  devices to it and know how to access them without reading the UML boot
+  log.  It is also unique in allowing access to a UML from remote
+  machines without requiring that the UML be networked.  This could be
+  useful in allowing public access to UMLs because they would be
+  accessible from the net, but wouldn't need any kind of network
+  filtering or access control because they would have no network access.
+
+
+  If you attach the main console to a portal, then the UML boot will
+  appear to hang.  In reality, it's waiting for a telnet to connect, at
+  which point the boot will proceed.
+
+
+
+
+
+  o  already-existing file descriptors - device=file descriptor
+
+
+     If you set up a file descriptor on the UML command line, you can
+     attach a UML device to it.  This is most commonly used to put the
+     main console back on stdin and stdout after assigning all the other
+     consoles to something else:
+
+
+        con0=fd:0,fd:1 con=pts
+
+
+
+
+
+
+
+
+  o  Nothing - device=null
+
+
+     This allows the device to be opened, in contrast to 'none', but
+     reads will block, and writes will succeed and the data will be
+     thrown out.
+
+
+
+
+
+  o  None - device=none
+
+
+     This causes the device to disappear.
+
+
+
+  You can also specify different input and output channels for a device
+  by putting a comma between them:
+
+
+        ssl3=tty:/dev/tty2,xterm
+
+
+
+
+  will cause serial line 3 to accept input on the host's /dev/tty2 and
+  display output on an xterm.  That's a silly example - the most common
+  use of this syntax is to reattach the main console to stdin and stdout
+  as shown above.
+
+
+  If you decide to move the main console away from stdin/stdout, the
+  initial boot output will appear in the terminal that you're running
+  UML in.  However, once the console driver has been officially
+  initialized, then the boot output will start appearing wherever you
+  specified that console 0 should be.  That device will receive all
+  subsequent output.
+
+
+
+  5.3.  Examples
+
+  There are a number of interesting things you can do with this
+  capability.
+
+
+  First, this is how you get rid of those bleeding console xterms by
+  attaching them to host ptys:
+
+
+        con=pty con0=fd:0,fd:1
+
+
+
+
+  This will make a UML console take over an unused host virtual console,
+  so that when you switch to it, you will see the UML login prompt
+  rather than the host login prompt:
+
+
+        con1=tty:/dev/tty6
+
+
+
+
+  You can attach two virtual machines together with what amounts to a
+  serial line as follows:
+
+  Run one UML with a serial line attached to a pty -
+
+
+        ssl1=pty
+
+
+
+
+  Look at the boot log to see what pty it got (this example will assume
+  that it got /dev/ptyp1).
+
+  Boot the other UML with a serial line attached to the corresponding
+  tty -
+
+
+        ssl1=tty:/dev/ttyp1
+
+
+
+
+  Log in, make sure that it has no getty on that serial line, attach a
+  terminal program like minicom to it, and you should see the login
+  prompt of the other virtual machine.
+
+
+  6.  Setting up the network
+
+
+
+  This page describes how to set up the various transports and to
+  provide a UML instance with network access to the host, other machines
+  on the local net, and the rest of the net.
+
+
+  As of 2.4.5, UML networking has been completely redone to make it much
+  easier to set up, fix bugs, and add new features.
+
+
+  There is a new helper, uml_net, which does the host setup that
+  requires root privileges.
+
+
+  There are currently five transport types available for a UML virtual
+  machine to exchange packets with other hosts:
+
+  o  ethertap
+
+  o  TUN/TAP
+
+  o  Multicast
+
+  o  a switch daemon
+
+  o  slip
+
+  o  slirp
+
+  o  pcap
+
+     The TUN/TAP, ethertap, slip, and slirp transports allow a UML
+     instance to exchange packets with the host.  They may be directed
+     to the host or the host may just act as a router to provide access
+     to other physical or virtual machines.
+
+
+  The pcap transport is a synthetic read-only interface, using the
+  libpcap binary to collect packets from interfaces on the host and
+  filter them.  This is useful for building preconfigured traffic
+  monitors or sniffers.
+
+
+  The daemon and multicast transports provide a completely virtual
+  network to other virtual machines.  This network is completely
+  disconnected from the physical network unless one of the virtual
+  machines on it is acting as a gateway.
+
+
+  With so many host transports, which one should you use?  Here's when
+  you should use each one:
+
+  o  ethertap - if you want access to the host networking and it is
+     running 2.2
+
+  o  TUN/TAP - if you want access to the host networking and it is
+     running 2.4.  Also, the TUN/TAP transport is able to use a
+     preconfigured device, allowing it to avoid using the setuid uml_net
+     helper, which is a security advantage.
+
+  o  Multicast - if you want a purely virtual network and you don't want
+     to set up anything but the UML
+
+  o  a switch daemon - if you want a purely virtual network and you
+     don't mind running the daemon in order to get somewhat better
+     performance
+
+  o  slip - there is no particular reason to run the slip backend unless
+     ethertap and TUN/TAP are just not available for some reason
+
+  o  slirp - if you don't have root access on the host to setup
+     networking, or if you don't want to allocate an IP to your UML
+
+  o  pcap - not much use for actual network connectivity, but great for
+     monitoring traffic on the host
+
+     Ethertap is available on 2.4 and works fine.  TUN/TAP is preferred
+     to it because it has better performance and ethertap is officially
+     considered obsolete in 2.4.  Also, the root helper only needs to
+     run occasionally for TUN/TAP, rather than handling every packet, as
+     it does with ethertap.  This is a slight security advantage since
+     it provides fewer opportunities for a nasty UML user to somehow
+     exploit the helper's root privileges.
+
+
+  6.1.  General setup
+
+  First, you must have the virtual network enabled in your UML.  If are
+  running a prebuilt kernel from this site, everything is already
+  enabled.  If you build the kernel yourself, under the "Network device
+  support" menu, enable "Network device support", and then the three
+  transports.
+
+
+  The next step is to provide a network device to the virtual machine.
+  This is done by describing it on the kernel command line.
+
+  The general format is
+
+
+       eth <n> = <transport> , <transport args>
+
+
+
+
+  For example, a virtual ethernet device may be attached to a host
+  ethertap device as follows:
+
+
+       eth0=ethertap,tap0,fe:fd:0:0:0:1,192.168.0.254
+
+
+
+
+  This sets up eth0 inside the virtual machine to attach itself to the
+  host /dev/tap0, assigns it an ethernet address, and assigns the host
+  tap0 interface an IP address.
+
+
+
+  Note that the IP address you assign to the host end of the tap device
+  must be different than the IP you assign to the eth device inside UML.
+  If you are short on IPs and don't want to consume two per UML, then
+  you can reuse the host's eth IP address for the host ends of the tap
+  devices.  Internally, the UMLs must still get unique IPs for their eth
+  devices.  You can also give the UMLs non-routable IPs (192.168.x.x or
+  10.x.x.x) and have the host masquerade them.  This will let outgoing
+  connections work, but incoming connections won't without more work,
+  such as port forwarding from the host.
+  Also note that when you configure the host side of an interface, it is
+  only acting as a gateway.  It will respond to pings sent to it
+  locally, but is not useful to do that since it's a host interface.
+  You are not talking to the UML when you ping that interface and get a
+  response.
+
+
+  You can also add devices to a UML and remove them at runtime.  See the
+  ``The Management Console''  page for details.
+
+
+  The sections below describe this in more detail.
+
+
+  Once you've decided how you're going to set up the devices, you boot
+  UML, log in, configure the UML side of the devices, and set up routes
+  to the outside world.  At that point, you will be able to talk to any
+  other machines, physical or virtual, on the net.
+
+
+  If ifconfig inside UML fails and the network refuses to come up, run
+  tell you what went wrong.
+
+
+
+  6.2.  Userspace daemons
+
+  You will likely need the setuid helper, or the switch daemon, or both.
+  They are both installed with the RPM and deb, so if you've installed
+  either, you can skip the rest of this section.
+
+
+  If not, then you need to check them out of CVS, build them, and
+  install them.  The helper is uml_net, in CVS /tools/uml_net, and the
+  daemon is uml_switch, in CVS /tools/uml_router.  They are both built
+  with a plain 'make'.  Both need to be installed in a directory that's
+  in your path - /usr/bin is recommend.  On top of that, uml_net needs
+  to be setuid root.
+
+
+
+  6.3.  Specifying ethernet addresses
+
+  Below, you will see that the TUN/TAP, ethertap, and daemon interfaces
+  allow you to specify hardware addresses for the virtual ethernet
+  devices.  This is generally not necessary.  If you don't have a
+  specific reason to do it, you probably shouldn't.  If one is not
+  specified on the command line, the driver will assign one based on the
+  device IP address.  It will provide the address fe:fd:nn:nn:nn:nn
+  where nn.nn.nn.nn is the device IP address.  This is nearly always
+  sufficient to guarantee a unique hardware address for the device.  A
+  couple of exceptions are:
+
+  o  Another set of virtual ethernet devices are on the same network and
+     they are assigned hardware addresses using a different scheme which
+     may conflict with the UML IP address-based scheme
+
+  o  You aren't going to use the device for IP networking, so you don't
+     assign the device an IP address
+
+     If you let the driver provide the hardware address, you should make
+     sure that the device IP address is known before the interface is
+     brought up.  So, inside UML, this will guarantee that:
+
+
+
+  UML#
+  ifconfig eth0 192.168.0.250 up
+
+
+
+
+  If you decide to assign the hardware address yourself, make sure that
+  the first byte of the address is even.  Addresses with an odd first
+  byte are broadcast addresses, which you don't want assigned to a
+  device.
+
+
+
+  6.4.  UML interface setup
+
+  Once the network devices have been described on the command line, you
+  should boot UML and log in.
+
+
+  The first thing to do is bring the interface up:
+
+
+       UML# ifconfig ethn ip-address up
+
+
+
+
+  You should be able to ping the host at this point.
+
+
+  To reach the rest of the world, you should set a default route to the
+  host:
+
+
+       UML# route add default gw host ip
+
+
+
+
+  Again, with host ip of 192.168.0.4:
+
+
+       UML# route add default gw 192.168.0.4
+
+
+
+
+  This page used to recommend setting a network route to your local net.
+  This is wrong, because it will cause UML to try to figure out hardware
+  addresses of the local machines by arping on the interface to the
+  host.  Since that interface is basically a single strand of ethernet
+  with two nodes on it (UML and the host) and arp requests don't cross
+  networks, they will fail to elicit any responses.  So, what you want
+  is for UML to just blindly throw all packets at the host and let it
+  figure out what to do with them, which is what leaving out the network
+  route and adding the default route does.
+
+
+  Note: If you can't communicate with other hosts on your physical
+  ethernet, it's probably because of a network route that's
+  automatically set up.  If you run 'route -n' and see a route that
+  looks like this:
+
+
+
+
+  Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
+  192.168.0.0     0.0.0.0         255.255.255.0   U     0      0      0   eth0
+
+
+
+
+  with a mask that's not 255.255.255.255, then replace it with a route
+  to your host:
+
+
+       UML#
+       route del -net 192.168.0.0 dev eth0 netmask 255.255.255.0
+
+
+
+
+
+
+       UML#
+       route add -host 192.168.0.4 dev eth0
+
+
+
+
+  This, plus the default route to the host, will allow UML to exchange
+  packets with any machine on your ethernet.
+
+
+
+  6.5.  Multicast
+
+  The simplest way to set up a virtual network between multiple UMLs is
+  to use the mcast transport.  This was written by Harald Welte and is
+  present in UML version 2.4.5-5um and later.  Your system must have
+  multicast enabled in the kernel and there must be a multicast-capable
+  network device on the host.  Normally, this is eth0, but if there is
+  no ethernet card on the host, then you will likely get strange error
+  messages when you bring the device up inside UML.
+
+
+  To use it, run two UMLs with
+
+
+        eth0=mcast
+
+
+
+
+  on their command lines.  Log in, configure the ethernet device in each
+  machine with different IP addresses:
+
+
+       UML1# ifconfig eth0 192.168.0.254
+
+
+
+
+
+
+       UML2# ifconfig eth0 192.168.0.253
+
+
+
+
+  and they should be able to talk to each other.
+
+  The full set of command line options for this transport are
+
+
+
+       ethn=mcast,ethernet address,multicast
+       address,multicast port,ttl
+
+
+
+
+  Harald's original README is here <http://user-mode-linux.source-
+  forge.net/>  and explains these in detail, as well as
+  some other issues.
+
+  There is also a related point-to-point only "ucast" transport.
+  This is useful when your network does not support multicast, and
+  all network connections are simple point to point links.
+
+  The full set of command line options for this transport are
+
+
+       ethn=ucast,ethernet address,remote address,listen port,remote port
+
+
+
+
+  6.6.  TUN/TAP with the uml_net helper
+
+  TUN/TAP is the preferred mechanism on 2.4 to exchange packets with the
+  host.  The TUN/TAP backend has been in UML since 2.4.9-3um.
+
+
+  The easiest way to get up and running is to let the setuid uml_net
+  helper do the host setup for you.  This involves insmod-ing the tun.o
+  module if necessary, configuring the device, and setting up IP
+  forwarding, routing, and proxy arp.  If you are new to UML networking,
+  do this first.  If you're concerned about the security implications of
+  the setuid helper, use it to get up and running, then read the next
+  section to see how to have UML use a preconfigured tap device, which
+  avoids the use of uml_net.
+
+
+  If you specify an IP address for the host side of the device, the
+  uml_net helper will do all necessary setup on the host - the only
+  requirement is that TUN/TAP be available, either built in to the host
+  kernel or as the tun.o module.
+
+  The format of the command line switch to attach a device to a TUN/TAP
+  device is
+
+
+       eth <n> =tuntap,,, <IP address>
+
+
+
+
+  For example, this argument will attach the UML's eth0 to the next
+  available tap device and assign an ethernet address to it based on its
+  IP address
+
+
+       eth0=tuntap,,,192.168.0.254
+
+
+
+
+
+
+  Note that the IP address that must be used for the eth device inside
+  UML is fixed by the routing and proxy arp that is set up on the
+  TUN/TAP device on the host.  You can use a different one, but it won't
+  work because reply packets won't reach the UML.  This is a feature.
+  It prevents a nasty UML user from doing things like setting the UML IP
+  to the same as the network's nameserver or mail server.
+
+
+  There are a couple potential problems with running the TUN/TAP
+  transport on a 2.4 host kernel
+
+  o  TUN/TAP seems not to work on 2.4.3 and earlier.  Upgrade the host
+     kernel or use the ethertap transport.
+
+  o  With an upgraded kernel, TUN/TAP may fail with
+
+
+       File descriptor in bad state
+
+
+
+
+  This is due to a header mismatch between the upgraded kernel and the
+  kernel that was originally installed on the machine.  The fix is to
+  make sure that /usr/src/linux points to the headers for the running
+  kernel.
+
+  These were pointed out by Tim Robinson <timro at trkr dot net> in
+  <http://www.geocrawler.com/> name="this uml-
+  user post"> .
+
+
+
+  6.7.  TUN/TAP with a preconfigured tap device
+
+  If you prefer not to have UML use uml_net (which is somewhat
+  insecure), with UML 2.4.17-11, you can set up a TUN/TAP device
+  beforehand.  The setup needs to be done as root, but once that's done,
+  there is no need for root assistance.  Setting up the device is done
+  as follows:
+
+  o  Create the device with tunctl (available from the UML utilities
+     tarball)
+
+
+
+
+       host#  tunctl -u uid
+
+
+
+
+  where uid is the user id or username that UML will be run as.  This
+  will tell you what device was created.
+
+  o  Configure the device IP (change IP addresses and device name to
+     suit)
+
+
+
+
+       host#  ifconfig tap0 192.168.0.254 up
+
+
+
+
+
+  o  Set up routing and arping if desired - this is my recipe, there are
+     other ways of doing the same thing
+
+
+       host#
+       bash -c 'echo 1 > /proc/sys/net/ipv4/ip_forward'
+
+       host#
+       route add -host 192.168.0.253 dev tap0
+
+
+
+
+
+
+       host#
+       bash -c 'echo 1 > /proc/sys/net/ipv4/conf/tap0/proxy_arp'
+
+
+
+
+
+
+       host#
+       arp -Ds 192.168.0.253 eth0 pub
+
+
+
+
+  Note that this must be done every time the host boots - this configu-
+  ration is not stored across host reboots.  So, it's probably a good
+  idea to stick it in an rc file.  An even better idea would be a little
+  utility which reads the information from a config file and sets up
+  devices at boot time.
+
+  o  Rather than using up two IPs and ARPing for one of them, you can
+     also provide direct access to your LAN by the UML by using a
+     bridge.
+
+
+       host#
+       brctl addbr br0
+
+
+
+
+
+
+       host#
+       ifconfig eth0 0.0.0.0 promisc up
+
+
+
+
+
+
+       host#
+       ifconfig tap0 0.0.0.0 promisc up
+
+
+
+
+
+
+       host#
+       ifconfig br0 192.168.0.1 netmask 255.255.255.0 up
+
+
+
+
+
+
+
+  host#
+  brctl stp br0 off
+
+
+
+
+
+
+       host#
+       brctl setfd br0 1
+
+
+
+
+
+
+       host#
+       brctl sethello br0 1
+
+
+
+
+
+
+       host#
+       brctl addif br0 eth0
+
+
+
+
+
+
+       host#
+       brctl addif br0 tap0
+
+
+
+
+  Note that 'br0' should be setup using ifconfig with the existing IP
+  address of eth0, as eth0 no longer has its own IP.
+
+  o
+
+
+     Also, the /dev/net/tun device must be writable by the user running
+     UML in order for the UML to use the device that's been configured
+     for it.  The simplest thing to do is
+
+
+       host#  chmod 666 /dev/net/tun
+
+
+
+
+  Making it world-writable looks bad, but it seems not to be
+  exploitable as a security hole.  However, it does allow anyone to cre-
+  ate useless tap devices (useless because they can't configure them),
+  which is a DOS attack.  A somewhat more secure alternative would to be
+  to create a group containing all the users who have preconfigured tap
+  devices and chgrp /dev/net/tun to that group with mode 664 or 660.
+
+
+  o  Once the device is set up, run UML with 'eth0=tuntap,device name'
+     (i.e. 'eth0=tuntap,tap0') on the command line (or do it with the
+     mconsole config command).
+
+  o  Bring the eth device up in UML and you're in business.
+
+     If you don't want that tap device any more, you can make it non-
+     persistent with
+
+
+       host#  tunctl -d tap device
+
+
+
+
+  Finally, tunctl has a -b (for brief mode) switch which causes it to
+  output only the name of the tap device it created.  This makes it
+  suitable for capture by a script:
+
+
+       host#  TAP=`tunctl -u 1000 -b`
+
+
+
+
+
+
+  6.8.  Ethertap
+
+  Ethertap is the general mechanism on 2.2 for userspace processes to
+  exchange packets with the kernel.
+
+
+
+  To use this transport, you need to describe the virtual network device
+  on the UML command line.  The general format for this is
+
+
+       eth <n> =ethertap, <device> , <ethernet address> , <tap IP address>
+
+
+
+
+  So, the previous example
+
+
+       eth0=ethertap,tap0,fe:fd:0:0:0:1,192.168.0.254
+
+
+
+
+  attaches the UML eth0 device to the host /dev/tap0, assigns it the
+  ethernet address fe:fd:0:0:0:1, and assigns the IP address
+  192.168.0.254 to the tap device.
+
+
+
+  The tap device is mandatory, but the others are optional.  If the
+  ethernet address is omitted, one will be assigned to it.
+
+
+  The presence of the tap IP address will cause the helper to run and do
+  whatever host setup is needed to allow the virtual machine to
+  communicate with the outside world.  If you're not sure you know what
+  you're doing, this is the way to go.
+
+
+  If it is absent, then you must configure the tap device and whatever
+  arping and routing you will need on the host.  However, even in this
+  case, the uml_net helper still needs to be in your path and it must be
+  setuid root if you're not running UML as root.  This is because the
+  tap device doesn't support SIGIO, which UML needs in order to use
+  something as a source of input.  So, the helper is used as a
+  convenient asynchronous IO thread.
+
+  If you're using the uml_net helper, you can ignore the following host
+  setup - uml_net will do it for you.  You just need to make sure you
+  have ethertap available, either built in to the host kernel or
+  available as a module.
+
+
+  If you want to set things up yourself, you need to make sure that the
+  appropriate /dev entry exists.  If it doesn't, become root and create
+  it as follows:
+
+
+       mknod /dev/tap <minor>  c 36  <minor>  + 16
+
+
+
+
+  For example, this is how to create /dev/tap0:
+
+
+       mknod /dev/tap0 c 36 0 + 16
+
+
+
+
+  You also need to make sure that the host kernel has ethertap support.
+  If ethertap is enabled as a module, you apparently need to insmod
+  ethertap once for each ethertap device you want to enable.  So,
+
+
+       host#
+       insmod ethertap
+
+
+
+
+  will give you the tap0 interface.  To get the tap1 interface, you need
+  to run
+
+
+       host#
+       insmod ethertap unit=1 -o ethertap1
+
+
+
+
+
+
+
+  6.9.  The switch daemon
+
+  Note: This is the daemon formerly known as uml_router, but which was
+  renamed so the network weenies of the world would stop growling at me.
+
+
+  The switch daemon, uml_switch, provides a mechanism for creating a
+  totally virtual network.  By default, it provides no connection to the
+  host network (but see -tap, below).
+
+
+  The first thing you need to do is run the daemon.  Running it with no
+  arguments will make it listen on a default pair of unix domain
+  sockets.
+
+
+  If you want it to listen on a different pair of sockets, use
+
+
+        -unix control socket data socket
+
+
+
+
+
+  If you want it to act as a hub rather than a switch, use
+
+
+        -hub
+
+
+
+
+
+  If you want the switch to be connected to host networking (allowing
+  the umls to get access to the outside world through the host), use
+
+
+        -tap tap0
+
+
+
+
+
+  Note that the tap device must be preconfigured (see "TUN/TAP with a
+  preconfigured tap device", above).  If you're using a different tap
+  device than tap0, specify that instead of tap0.
+
+
+  uml_switch can be backgrounded as follows
+
+
+       host%
+       uml_switch [ options ] < /dev/null > /dev/null
+
+
+
+
+  The reason it doesn't background by default is that it listens to
+  stdin for EOF.  When it sees that, it exits.
+
+
+  The general format of the kernel command line switch is
+
+
+
+       ethn=daemon,ethernet address,socket
+       type,control socket,data socket
+
+
+
+
+  You can leave off everything except the 'daemon'.  You only need to
+  specify the ethernet address if the one that will be assigned to it
+  isn't acceptable for some reason.  The rest of the arguments describe
+  how to communicate with the daemon.  You should only specify them if
+  you told the daemon to use different sockets than the default.  So, if
+  you ran the daemon with no arguments, running the UML on the same
+  machine with
+       eth0=daemon
+
+
+
+
+  will cause the eth0 driver to attach itself to the daemon correctly.
+
+
+
+  6.10.  Slip
+
+  Slip is another, less general, mechanism for a process to communicate
+  with the host networking.  In contrast to the ethertap interface,
+  which exchanges ethernet frames with the host and can be used to
+  transport any higher-level protocol, it can only be used to transport
+  IP.
+
+
+  The general format of the command line switch is
+
+
+
+       ethn=slip,slip IP
+
+
+
+
+  The slip IP argument is the IP address that will be assigned to the
+  host end of the slip device.  If it is specified, the helper will run
+  and will set up the host so that the virtual machine can reach it and
+  the rest of the network.
+
+
+  There are some oddities with this interface that you should be aware
+  of.  You should only specify one slip device on a given virtual
+  machine, and its name inside UML will be 'umn', not 'eth0' or whatever
+  you specified on the command line.  These problems will be fixed at
+  some point.
+
+
+
+  6.11.  Slirp
+
+  slirp uses an external program, usually /usr/bin/slirp, to provide IP
+  only networking connectivity through the host. This is similar to IP
+  masquerading with a firewall, although the translation is performed in
+  user-space, rather than by the kernel.  As slirp does not set up any
+  interfaces on the host, or changes routing, slirp does not require
+  root access or setuid binaries on the host.
+
+
+  The general format of the command line switch for slirp is:
+
+
+
+       ethn=slirp,ethernet address,slirp path
+
+
+
+
+  The ethernet address is optional, as UML will set up the interface
+  with an ethernet address based upon the initial IP address of the
+  interface.  The slirp path is generally /usr/bin/slirp, although it
+  will depend on distribution.
+
+
+  The slirp program can have a number of options passed to the command
+  line and we can't add them to the UML command line, as they will be
+  parsed incorrectly.  Instead, a wrapper shell script can be written or
+  the options inserted into the  /.slirprc file.  More information on
+  all of the slirp options can be found in its man pages.
+
+
+  The eth0 interface on UML should be set up with the IP 10.2.0.15,
+  although you can use anything as long as it is not used by a network
+  you will be connecting to. The default route on UML should be set to
+  use
+
+
+       UML#
+       route add default dev eth0
+
+
+
+
+  slirp provides a number of useful IP addresses which can be used by
+  UML, such as 10.0.2.3 which is an alias for the DNS server specified
+  in /etc/resolv.conf on the host or the IP given in the 'dns' option
+  for slirp.
+
+
+  Even with a baudrate setting higher than 115200, the slirp connection
+  is limited to 115200. If you need it to go faster, the slirp binary
+  needs to be compiled with FULL_BOLT defined in config.h.
+
+
+
+  6.12.  pcap
+
+  The pcap transport is attached to a UML ethernet device on the command
+  line or with uml_mconsole with the following syntax:
+
+
+
+       ethn=pcap,host interface,filter
+       expression,option1,option2
+
+
+
+
+  The expression and options are optional.
+
+
+  The interface is whatever network device on the host you want to
+  sniff.  The expression is a pcap filter expression, which is also what
+  tcpdump uses, so if you know how to specify tcpdump filters, you will
+  use the same expressions here.  The options are up to two of
+  'promisc', control whether pcap puts the host interface into
+  promiscuous mode. 'optimize' and 'nooptimize' control whether the pcap
+  expression optimizer is used.
+
+
+  Example:
+
+
+
+       eth0=pcap,eth0,tcp
+
+       eth1=pcap,eth0,!tcp
+
+
+
+  will cause the UML eth0 to emit all tcp packets on the host eth0 and
+  the UML eth1 to emit all non-tcp packets on the host eth0.
+
+
+
+  6.13.  Setting up the host yourself
+
+  If you don't specify an address for the host side of the ethertap or
+  slip device, UML won't do any setup on the host.  So this is what is
+  needed to get things working (the examples use a host-side IP of
+  192.168.0.251 and a UML-side IP of 192.168.0.250 - adjust to suit your
+  own network):
+
+  o  The device needs to be configured with its IP address.  Tap devices
+     are also configured with an mtu of 1484.  Slip devices are
+     configured with a point-to-point address pointing at the UML ip
+     address.
+
+
+       host#  ifconfig tap0 arp mtu 1484 192.168.0.251 up
+
+
+
+
+
+
+       host#
+       ifconfig sl0 192.168.0.251 pointopoint 192.168.0.250 up
+
+
+
+
+
+  o  If a tap device is being set up, a route is set to the UML IP.
+
+
+       UML# route add -host 192.168.0.250 gw 192.168.0.251
+
+
+
+
+
+  o  To allow other hosts on your network to see the virtual machine,
+     proxy arp is set up for it.
+
+
+       host#  arp -Ds 192.168.0.250 eth0 pub
+
+
+
+
+
+  o  Finally, the host is set up to route packets.
+
+
+       host#  echo 1 > /proc/sys/net/ipv4/ip_forward
+
+
+
+
+
+
+
+
+
+
+  7.  Sharing Filesystems between Virtual Machines
+
+
+
+
+  7.1.  A warning
+
+  Don't attempt to share filesystems simply by booting two UMLs from the
+  same file.  That's the same thing as booting two physical machines
+  from a shared disk.  It will result in filesystem corruption.
+
+
+
+  7.2.  Using layered block devices
+
+  The way to share a filesystem between two virtual machines is to use
+  the copy-on-write (COW) layering capability of the ubd block driver.
+  As of 2.4.6-2um, the driver supports layering a read-write private
+  device over a read-only shared device.  A machine's writes are stored
+  in the private device, while reads come from either device - the
+  private one if the requested block is valid in it, the shared one if
+  not.  Using this scheme, the majority of data which is unchanged is
+  shared between an arbitrary number of virtual machines, each of which
+  has a much smaller file containing the changes that it has made.  With
+  a large number of UMLs booting from a large root filesystem, this
+  leads to a huge disk space saving.  It will also help performance,
+  since the host will be able to cache the shared data using a much
+  smaller amount of memory, so UML disk requests will be served from the
+  host's memory rather than its disks.
+
+
+
+
+  To add a copy-on-write layer to an existing block device file, simply
+  add the name of the COW file to the appropriate ubd switch:
+
+
+        ubd0=root_fs_cow,root_fs_debian_22
+
+
+
+
+  where 'root_fs_cow' is the private COW file and 'root_fs_debian_22' is
+  the existing shared filesystem.  The COW file need not exist.  If it
+  doesn't, the driver will create and initialize it.  Once the COW file
+  has been initialized, it can be used on its own on the command line:
+
+
+        ubd0=root_fs_cow
+
+
+
+
+  The name of the backing file is stored in the COW file header, so it
+  would be redundant to continue specifying it on the command line.
+
+
+
+  7.3.  Note!
+
+  When checking the size of the COW file in order to see the gobs of
+  space that you're saving, make sure you use 'ls -ls' to see the actual
+  disk consumption rather than the length of the file.  The COW file is
+  sparse, so the length will be very different from the disk usage.
+  Here is a 'ls -l' of a COW file and backing file from one boot and
+  shutdown:
+       host% ls -l cow.debian debian2.2
+       -rw-r--r--    1 jdike    jdike    492504064 Aug  6 21:16 cow.debian
+       -rwxrw-rw-    1 jdike    jdike    537919488 Aug  6 20:42 debian2.2
+
+
+
+
+  Doesn't look like much saved space, does it?  Well, here's 'ls -ls':
+
+
+       host% ls -ls cow.debian debian2.2
+          880 -rw-r--r--    1 jdike    jdike    492504064 Aug  6 21:16 cow.debian
+       525832 -rwxrw-rw-    1 jdike    jdike    537919488 Aug  6 20:42 debian2.2
+
+
+
+
+  Now, you can see that the COW file has less than a meg of disk, rather
+  than 492 meg.
+
+
+
+  7.4.  Another warning
+
+  Once a filesystem is being used as a readonly backing file for a COW
+  file, do not boot directly from it or modify it in any way.  Doing so
+  will invalidate any COW files that are using it.  The mtime and size
+  of the backing file are stored in the COW file header at its creation,
+  and they must continue to match.  If they don't, the driver will
+  refuse to use the COW file.
+
+
+
+
+  If you attempt to evade this restriction by changing either the
+  backing file or the COW header by hand, you will get a corrupted
+  filesystem.
+
+
+
+
+  Among other things, this means that upgrading the distribution in a
+  backing file and expecting that all of the COW files using it will see
+  the upgrade will not work.
+
+
+
+
+  7.5.  uml_moo : Merging a COW file with its backing file
+
+  Depending on how you use UML and COW devices, it may be advisable to
+  merge the changes in the COW file into the backing file every once in
+  a while.
+
+
+
+
+  The utility that does this is uml_moo.  Its usage is
+
+
+       host% uml_moo COW file new backing file
+
+
+
+
+  There's no need to specify the backing file since that information is
+  already in the COW file header.  If you're paranoid, boot the new
+  merged file, and if you're happy with it, move it over the old backing
+  file.
+
+
+
+
+  uml_moo creates a new backing file by default as a safety measure.  It
+  also has a destructive merge option which will merge the COW file
+  directly into its current backing file.  This is really only usable
+  when the backing file only has one COW file associated with it.  If
+  there are multiple COWs associated with a backing file, a -d merge of
+  one of them will invalidate all of the others.  However, it is
+  convenient if you're short of disk space, and it should also be
+  noticeably faster than a non-destructive merge.
+
+
+
+
+  uml_moo is installed with the UML deb and RPM.  If you didn't install
+  UML from one of those packages, you can also get it from the UML
+  utilities <http://user-mode-linux.sourceforge.net/
+  utilities>  tar file in tools/moo.
+
+
+
+
+
+
+
+
+  8.  Creating filesystems
+
+
+  You may want to create and mount new UML filesystems, either because
+  your root filesystem isn't large enough or because you want to use a
+  filesystem other than ext2.
+
+
+  This was written on the occasion of reiserfs being included in the
+  2.4.1 kernel pool, and therefore the 2.4.1 UML, so the examples will
+  talk about reiserfs.  This information is generic, and the examples
+  should be easy to translate to the filesystem of your choice.
+
+
+  8.1.  Create the filesystem file
+
+  dd is your friend.  All you need to do is tell dd to create an empty
+  file of the appropriate size.  I usually make it sparse to save time
+  and to avoid allocating disk space until it's actually used.  For
+  example, the following command will create a sparse 100 meg file full
+  of zeroes.
+
+
+       host%
+       dd if=/dev/zero of=new_filesystem seek=100 count=1 bs=1M
+
+
+
+
+
+
+  8.2.  Assign the file to a UML device
+
+  Add an argument like the following to the UML command line:
+
+  ubd4=new_filesystem
+
+
+
+
+  making sure that you use an unassigned ubd device number.
+
+
+
+  8.3.  Creating and mounting the filesystem
+
+  Make sure that the filesystem is available, either by being built into
+  the kernel, or available as a module, then boot up UML and log in.  If
+  the root filesystem doesn't have the filesystem utilities (mkfs, fsck,
+  etc), then get them into UML by way of the net or hostfs.
+
+
+  Make the new filesystem on the device assigned to the new file:
+
+
+       host#  mkreiserfs /dev/ubd/4
+
+
+       <----------- MKREISERFSv2 ----------->
+
+       ReiserFS version 3.6.25
+       Block size 4096 bytes
+       Block count 25856
+       Used blocks 8212
+               Journal - 8192 blocks (18-8209), journal header is in block 8210
+               Bitmaps: 17
+               Root block 8211
+       Hash function "r5"
+       ATTENTION: ALL DATA WILL BE LOST ON '/dev/ubd/4'! (y/n)y
+       journal size 8192 (from 18)
+       Initializing journal - 0%....20%....40%....60%....80%....100%
+       Syncing..done.
+
+
+
+
+  Now, mount it:
+
+
+       UML#
+       mount /dev/ubd/4 /mnt
+
+
+
+
+  and you're in business.
+
+
+
+
+
+
+
+
+
+  9.  Host file access
+
+
+  If you want to access files on the host machine from inside UML, you
+  can treat it as a separate machine and either nfs mount directories
+  from the host or copy files into the virtual machine with scp or rcp.
+  However, since UML is running on the host, it can access those
+  files just like any other process and make them available inside the
+  virtual machine without needing to use the network.
+
+
+  This is now possible with the hostfs virtual filesystem.  With it, you
+  can mount a host directory into the UML filesystem and access the
+  files contained in it just as you would on the host.
+
+
+  9.1.  Using hostfs
+
+  To begin with, make sure that hostfs is available inside the virtual
+  machine with
+
+
+       UML# cat /proc/filesystems
+
+
+
+  .  hostfs should be listed.  If it's not, either rebuild the kernel
+  with hostfs configured into it or make sure that hostfs is built as a
+  module and available inside the virtual machine, and insmod it.
+
+
+  Now all you need to do is run mount:
+
+
+       UML# mount none /mnt/host -t hostfs
+
+
+
+
+  will mount the host's / on the virtual machine's /mnt/host.
+
+
+  If you don't want to mount the host root directory, then you can
+  specify a subdirectory to mount with the -o switch to mount:
+
+
+       UML# mount none /mnt/home -t hostfs -o /home
+
+
+
+
+  will mount the hosts's /home on the virtual machine's /mnt/home.
+
+
+
+  9.2.  hostfs as the root filesystem
+
+  It's possible to boot from a directory hierarchy on the host using
+  hostfs rather than using the standard filesystem in a file.
+
+  To start, you need that hierarchy.  The easiest way is to loop mount
+  an existing root_fs file:
+
+
+       host#  mount root_fs uml_root_dir -o loop
+
+
+
+
+  You need to change the filesystem type of / in etc/fstab to be
+  'hostfs', so that line looks like this:
+
+  /dev/ubd/0       /        hostfs      defaults          1   1
+
+
+
+
+  Then you need to chown to yourself all the files in that directory
+  that are owned by root.  This worked for me:
+
+
+       host#  find . -uid 0 -exec chown jdike {} \;
+
+
+
+
+  Next, make sure that your UML kernel has hostfs compiled in, not as a
+  module.  Then run UML with the boot device pointing at that directory:
+
+
+        ubd0=/path/to/uml/root/directory
+
+
+
+
+  UML should then boot as it does normally.
+
+
+  9.3.  Building hostfs
+
+  If you need to build hostfs because it's not in your kernel, you have
+  two choices:
+
+
+
+  o  Compiling hostfs into the kernel:
+
+
+     Reconfigure the kernel and set the 'Host filesystem' option under
+
+
+  o  Compiling hostfs as a module:
+
+
+     Reconfigure the kernel and set the 'Host filesystem' option under
+     be in arch/um/fs/hostfs/hostfs.o.  Install that in
+     /lib/modules/`uname -r`/fs in the virtual machine, boot it up, and
+
+
+       UML# insmod hostfs
+
+
+
+
+
+
+
+
+
+
+
+
+  10.  The Management Console
+
+
+
+  The UML management console is a low-level interface to the kernel,
+  somewhat like the i386 SysRq interface.  Since there is a full-blown
+  operating system under UML, there is much greater flexibility possible
+  than with the SysRq mechanism.
+
+
+  There are a number of things you can do with the mconsole interface:
+
+  o  get the kernel version
+
+  o  add and remove devices
+
+  o  halt or reboot the machine
+
+  o  Send SysRq commands
+
+  o  Pause and resume the UML
+
+
+  You need the mconsole client (uml_mconsole) which is present in CVS
+  (/tools/mconsole) in 2.4.5-9um and later, and will be in the RPM in
+  2.4.6.
+
+
+  You also need CONFIG_MCONSOLE (under 'General Setup') enabled in UML.
+  When you boot UML, you'll see a line like:
+
+
+       mconsole initialized on /home/jdike/.uml/umlNJ32yL/mconsole
+
+
+
+
+  If you specify a unique machine id one the UML command line, i.e.
+
+
+        umid=debian
+
+
+
+
+  you'll see this
+
+
+       mconsole initialized on /home/jdike/.uml/debian/mconsole
+
+
+
+
+  That file is the socket that uml_mconsole will use to communicate with
+  UML.  Run it with either the umid or the full path as its argument:
+
+
+       host% uml_mconsole debian
+
+
+
+
+  or
+
+
+       host% uml_mconsole /home/jdike/.uml/debian/mconsole
+
+
+
+
+  You'll get a prompt, at which you can run one of these commands:
+
+  o  version
+
+  o  halt
+
+  o  reboot
+
+  o  config
+
+  o  remove
+
+  o  sysrq
+
+  o  help
+
+  o  cad
+
+  o  stop
+
+  o  go
+
+
+  10.1.  version
+
+  This takes no arguments.  It prints the UML version.
+
+
+       (mconsole)  version
+       OK Linux usermode 2.4.5-9um #1 Wed Jun 20 22:47:08 EDT 2001 i686
+
+
+
+
+  There are a couple actual uses for this.  It's a simple no-op which
+  can be used to check that a UML is running.  It's also a way of
+  sending an interrupt to the UML.  This is sometimes useful on SMP
+  hosts, where there's a bug which causes signals to UML to be lost,
+  often causing it to appear to hang.  Sending such a UML the mconsole
+  version command is a good way to 'wake it up' before networking has
+  been enabled, as it does not do anything to the function of the UML.
+
+
+
+  10.2.  halt and reboot
+
+  These take no arguments.  They shut the machine down immediately, with
+  no syncing of disks and no clean shutdown of userspace.  So, they are
+  pretty close to crashing the machine.
+
+
+       (mconsole)  halt
+       OK
+
+
+
+
+
+
+  10.3.  config
+
+  "config" adds a new device to the virtual machine.  Currently the ubd
+  and network drivers support this.  It takes one argument, which is the
+  device to add, with the same syntax as the kernel command line.
+
+
+
+
+  (mconsole)
+  config ubd3=/home/jdike/incoming/roots/root_fs_debian22
+
+  OK
+  (mconsole)  config eth1=mcast
+  OK
+
+
+
+
+
+
+  10.4.  remove
+
+  "remove" deletes a device from the system.  Its argument is just the
+  name of the device to be removed. The device must be idle in whatever
+  sense the driver considers necessary.  In the case of the ubd driver,
+  the removed block device must not be mounted, swapped on, or otherwise
+  open, and in the case of the network driver, the device must be down.
+
+
+       (mconsole)  remove ubd3
+       OK
+       (mconsole)  remove eth1
+       OK
+
+
+
+
+
+
+  10.5.  sysrq
+
+  This takes one argument, which is a single letter.  It calls the
+  generic kernel's SysRq driver, which does whatever is called for by
+  that argument.  See the SysRq documentation in
+  Documentation/admin-guide/sysrq.rst in your favorite kernel tree to
+  see what letters are valid and what they do.
+
+
+
+  10.6.  help
+
+  "help" returns a string listing the valid commands and what each one
+  does.
+
+
+
+  10.7.  cad
+
+  This invokes the Ctl-Alt-Del action on init.  What exactly this ends
+  up doing is up to /etc/inittab.  Normally, it reboots the machine.
+  With UML, this is usually not desired, so if a halt would be better,
+  then find the section of inittab that looks like this
+
+
+       # What to do when CTRL-ALT-DEL is pressed.
+       ca:12345:ctrlaltdel:/sbin/shutdown -t1 -a -r now
+
+
+
+
+  and change the command to halt.
+
+
+
+  10.8.  stop
+
+  This puts the UML in a loop reading mconsole requests until a 'go'
+  mconsole command is received. This is very useful for making backups
+  of UML filesystems, as the UML can be stopped, then synced via 'sysrq
+  s', so that everything is written to the filesystem. You can then copy
+  the filesystem and then send the UML 'go' via mconsole.
+
+
+  Note that a UML running with more than one CPU will have problems
+  after you send the 'stop' command, as only one CPU will be held in a
+  mconsole loop and all others will continue as normal.  This is a bug,
+  and will be fixed.
+
+
+
+  10.9.  go
+
+  This resumes a UML after being paused by a 'stop' command. Note that
+  when the UML has resumed, TCP connections may have timed out and if
+  the UML is paused for a long period of time, crond might go a little
+  crazy, running all the jobs it didn't do earlier.
+
+
+
+
+
+
+
+
+  11.  Kernel debugging
+
+
+  Note: The interface that makes debugging, as described here, possible
+  is present in 2.4.0-test6 kernels and later.
+
+
+  Since the user-mode kernel runs as a normal Linux process, it is
+  possible to debug it with gdb almost like any other process.  It is
+  slightly different because the kernel's threads are already being
+  ptraced for system call interception, so gdb can't ptrace them.
+  However, a mechanism has been added to work around that problem.
+
+
+  In order to debug the kernel, you need build it from source.  See
+  ``Compiling the kernel and modules''  for information on doing that.
+  Make sure that you enable CONFIG_DEBUGSYM and CONFIG_PT_PROXY during
+  the config.  These will compile the kernel with -g, and enable the
+  ptrace proxy so that gdb works with UML, respectively.
+
+
+
+
+  11.1.  Starting the kernel under gdb
+
+  You can have the kernel running under the control of gdb from the
+  beginning by putting 'debug' on the command line.  You will get an
+  xterm with gdb running inside it.  The kernel will send some commands
+  to gdb which will leave it stopped at the beginning of start_kernel.
+  At this point, you can get things going with 'next', 'step', or
+  'cont'.
+
+
+  There is a transcript of a debugging session  here <debug-
+  session.html> , with breakpoints being set in the scheduler and in an
+  interrupt handler.
+  11.2.  Examining sleeping processes
+
+  Not every bug is evident in the currently running process.  Sometimes,
+  processes hang in the kernel when they shouldn't because they've
+  deadlocked on a semaphore or something similar.  In this case, when
+  you ^C gdb and get a backtrace, you will see the idle thread, which
+  isn't very relevant.
+
+
+  What you want is the stack of whatever process is sleeping when it
+  shouldn't be.  You need to figure out which process that is, which is
+  generally fairly easy.  Then you need to get its host process id,
+  which you can do either by looking at ps on the host or at
+  task.thread.extern_pid in gdb.
+
+
+  Now what you do is this:
+
+  o  detach from the current thread
+
+
+       (UML gdb)  det
+
+
+
+
+
+  o  attach to the thread you are interested in
+
+
+       (UML gdb)  att <host pid>
+
+
+
+
+
+  o  look at its stack and anything else of interest
+
+
+       (UML gdb)  bt
+
+
+
+
+  Note that you can't do anything at this point that requires that a
+  process execute, e.g. calling a function
+
+  o  when you're done looking at that process, reattach to the current
+     thread and continue it
+
+
+       (UML gdb)
+       att 1
+
+
+
+
+
+
+       (UML gdb)
+       c
+
+
+
+
+  Here, specifying any pid which is not the process id of a UML thread
+  will cause gdb to reattach to the current thread.  I commonly use 1,
+  but any other invalid pid would work.
+
+
+
+  11.3.  Running ddd on UML
+
+  ddd works on UML, but requires a special kludge.  The process goes
+  like this:
+
+  o  Start ddd
+
+
+       host% ddd linux
+
+
+
+
+
+  o  With ps, get the pid of the gdb that ddd started.  You can ask the
+     gdb to tell you, but for some reason that confuses things and
+     causes a hang.
+
+  o  run UML with 'debug=parent gdb-pid=<pid>' added to the command line
+     - it will just sit there after you hit return
+
+  o  type 'att 1' to the ddd gdb and you will see something like
+
+
+       0xa013dc51 in __kill ()
+
+
+       (gdb)
+
+
+
+
+
+  o  At this point, type 'c', UML will boot up, and you can use ddd just
+     as you do on any other process.
+
+
+
+  11.4.  Debugging modules
+
+  gdb has support for debugging code which is dynamically loaded into
+  the process.  This support is what is needed to debug kernel modules
+  under UML.
+
+
+  Using that support is somewhat complicated.  You have to tell gdb what
+  object file you just loaded into UML and where in memory it is.  Then,
+  it can read the symbol table, and figure out where all the symbols are
+  from the load address that you provided.  It gets more interesting
+  when you load the module again (i.e. after an rmmod).  You have to
+  tell gdb to forget about all its symbols, including the main UML ones
+  for some reason, then load then all back in again.
+
+
+  There's an easy way and a hard way to do this.  The easy way is to use
+  the umlgdb expect script written by Chandan Kudige.  It basically
+  automates the process for you.
+
+
+  First, you must tell it where your modules are.  There is a list in
+  the script that looks like this:
+       set MODULE_PATHS {
+       "fat" "/usr/src/uml/linux-2.4.18/fs/fat/fat.o"
+       "isofs" "/usr/src/uml/linux-2.4.18/fs/isofs/isofs.o"
+       "minix" "/usr/src/uml/linux-2.4.18/fs/minix/minix.o"
+       }
+
+
+
+
+  You change that to list the names and paths of the modules that you
+  are going to debug.  Then you run it from the toplevel directory of
+  your UML pool and it basically tells you what to do:
+
+
+
+
+                   ******** GDB pid is 21903 ********
+       Start UML as: ./linux <kernel switches> debug gdb-pid=21903
+
+
+
+       GNU gdb 5.0rh-5 Red Hat Linux 7.1
+       Copyright 2001 Free Software Foundation, Inc.
+       GDB is free software, covered by the GNU General Public License, and you are
+       welcome to change it and/or distribute copies of it under certain conditions.
+       Type "show copying" to see the conditions.
+       There is absolutely no warranty for GDB.  Type "show warranty" for details.
+       This GDB was configured as "i386-redhat-linux"...
+       (gdb) b sys_init_module
+       Breakpoint 1 at 0xa0011923: file module.c, line 349.
+       (gdb) att 1
+
+
+
+
+  After you run UML and it sits there doing nothing, you hit return at
+  the 'att 1' and continue it:
+
+
+       Attaching to program: /home/jdike/linux/2.4/um/./linux, process 1
+       0xa00f4221 in __kill ()
+       (UML gdb)  c
+       Continuing.
+
+
+
+
+  At this point, you debug normally.  When you insmod something, the
+  expect magic will kick in and you'll see something like:
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+   *** Module hostfs loaded ***
+  Breakpoint 1, sys_init_module (name_user=0x805abb0 "hostfs",
+      mod_user=0x8070e00) at module.c:349
+  349             char *name, *n_name, *name_tmp = NULL;
+  (UML gdb)  finish
+  Run till exit from #0  sys_init_module (name_user=0x805abb0 "hostfs",
+      mod_user=0x8070e00) at module.c:349
+  0xa00e2e23 in execute_syscall (r=0xa8140284) at syscall_kern.c:411
+  411             else res = EXECUTE_SYSCALL(syscall, regs);
+  Value returned is $1 = 0
+  (UML gdb)
+  p/x (int)module_list + module_list->size_of_struct
+
+  $2 = 0xa9021054
+  (UML gdb)  symbol-file ./linux
+  Load new symbol table from "./linux"? (y or n) y
+  Reading symbols from ./linux...
+  done.
+  (UML gdb)
+  add-symbol-file /home/jdike/linux/2.4/um/arch/um/fs/hostfs/hostfs.o 0xa9021054
+
+  add symbol table from file "/home/jdike/linux/2.4/um/arch/um/fs/hostfs/hostfs.o" at
+          .text_addr = 0xa9021054
+   (y or n) y
+
+  Reading symbols from /home/jdike/linux/2.4/um/arch/um/fs/hostfs/hostfs.o...
+  done.
+  (UML gdb)  p *module_list
+  $1 = {size_of_struct = 84, next = 0xa0178720, name = 0xa9022de0 "hostfs",
+    size = 9016, uc = {usecount = {counter = 0}, pad = 0}, flags = 1,
+    nsyms = 57, ndeps = 0, syms = 0xa9023170, deps = 0x0, refs = 0x0,
+    init = 0xa90221f0 <init_hostfs>, cleanup = 0xa902222c <exit_hostfs>,
+    ex_table_start = 0x0, ex_table_end = 0x0, persist_start = 0x0,
+    persist_end = 0x0, can_unload = 0, runsize = 0, kallsyms_start = 0x0,
+    kallsyms_end = 0x0,
+    archdata_start = 0x1b855 <Address 0x1b855 out of bounds>,
+    archdata_end = 0xe5890000 <Address 0xe5890000 out of bounds>,
+    kernel_data = 0xf689c35d <Address 0xf689c35d out of bounds>}
+  >> Finished loading symbols for hostfs ...
+
+
+
+
+  That's the easy way.  It's highly recommended.  The hard way is
+  described below in case you're interested in what's going on.
+
+
+  Boot the kernel under the debugger and load the module with insmod or
+  modprobe.  With gdb, do:
+
+
+       (UML gdb)  p module_list
+
+
+
+
+  This is a list of modules that have been loaded into the kernel, with
+  the most recently loaded module first.  Normally, the module you want
+  is at module_list.  If it's not, walk down the next links, looking at
+  the name fields until find the module you want to debug.  Take the
+  address of that structure, and add module.size_of_struct (which in
+  2.4.10 kernels is 96 (0x60)) to it.  Gdb can make this hard addition
+  for you :-):
+
+
+
+  (UML gdb)
+  printf "%#x\n", (int)module_list module_list->size_of_struct
+
+
+
+
+  The offset from the module start occasionally changes (before 2.4.0,
+  it was module.size_of_struct + 4), so it's a good idea to check the
+  init and cleanup addresses once in a while, as describe below.  Now
+  do:
+
+
+       (UML gdb)
+       add-symbol-file /path/to/module/on/host that_address
+
+
+
+
+  Tell gdb you really want to do it, and you're in business.
+
+
+  If there's any doubt that you got the offset right, like breakpoints
+  appear not to work, or they're appearing in the wrong place, you can
+  check it by looking at the module structure.  The init and cleanup
+  fields should look like:
+
+
+       init = 0x588066b0 <init_hostfs>, cleanup = 0x588066c0 <exit_hostfs>
+
+
+
+
+  with no offsets on the symbol names.  If the names are right, but they
+  are offset, then the offset tells you how much you need to add to the
+  address you gave to add-symbol-file.
+
+
+  When you want to load in a new version of the module, you need to get
+  gdb to forget about the old one.  The only way I've found to do that
+  is to tell gdb to forget about all symbols that it knows about:
+
+
+       (UML gdb)  symbol-file
+
+
+
+
+  Then reload the symbols from the kernel binary:
+
+
+       (UML gdb)  symbol-file /path/to/kernel
+
+
+
+
+  and repeat the process above.  You'll also need to re-enable break-
+  points.  They were disabled when you dumped all the symbols because
+  gdb couldn't figure out where they should go.
+
+
+
+  11.5.  Attaching gdb to the kernel
+
+  If you don't have the kernel running under gdb, you can attach gdb to
+  it later by sending the tracing thread a SIGUSR1.  The first line of
+  the console output identifies its pid:
+       tracing thread pid = 20093
+
+
+
+
+  When you send it the signal:
+
+
+       host% kill -USR1 20093
+
+
+
+
+  you will get an xterm with gdb running in it.
+
+
+  If you have the mconsole compiled into UML, then the mconsole client
+  can be used to start gdb:
+
+
+       (mconsole)  (mconsole) config gdb=xterm
+
+
+
+
+  will fire up an xterm with gdb running in it.
+
+
+
+  11.6.  Using alternate debuggers
+
+  UML has support for attaching to an already running debugger rather
+  than starting gdb itself.  This is present in CVS as of 17 Apr 2001.
+  I sent it to Alan for inclusion in the ac tree, and it will be in my
+  2.4.4 release.
+
+
+  This is useful when gdb is a subprocess of some UI, such as emacs or
+  ddd.  It can also be used to run debuggers other than gdb on UML.
+  Below is an example of using strace as an alternate debugger.
+
+
+  To do this, you need to get the pid of the debugger and pass it in
+  with the
+
+
+  If you are using gdb under some UI, then tell it to 'att 1', and
+  you'll find yourself attached to UML.
+
+
+  If you are using something other than gdb as your debugger, then
+  you'll need to get it to do the equivalent of 'att 1' if it doesn't do
+  it automatically.
+
+
+  An example of an alternate debugger is strace.  You can strace the
+  actual kernel as follows:
+
+  o  Run the following in a shell
+
+
+       host%
+       sh -c 'echo pid=$$; echo -n hit return; read x; exec strace -p 1 -o strace.out'
+
+
+
+  o  Run UML with 'debug' and 'gdb-pid=<pid>' with the pid printed out
+     by the previous command
+
+  o  Hit return in the shell, and UML will start running, and strace
+     output will start accumulating in the output file.
+
+     Note that this is different from running
+
+
+       host% strace ./linux
+
+
+
+
+  That will strace only the main UML thread, the tracing thread, which
+  doesn't do any of the actual kernel work.  It just oversees the vir-
+  tual machine.  In contrast, using strace as described above will show
+  you the low-level activity of the virtual machine.
+
+
+
+
+
+  12.  Kernel debugging examples
+
+  12.1.  The case of the hung fsck
+
+  When booting up the kernel, fsck failed, and dropped me into a shell
+  to fix things up.  I ran fsck -y, which hung:
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+  Setting hostname uml                    [ OK ]
+  Checking root filesystem
+  /dev/fhd0 was not cleanly unmounted, check forced.
+  Error reading block 86894 (Attempt to read block from filesystem resulted in short read) while reading indirect blocks of inode 19780.
+
+  /dev/fhd0: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
+          (i.e., without -a or -p options)
+  [ FAILED ]
+
+  *** An error occurred during the file system check.
+  *** Dropping you to a shell; the system will reboot
+  *** when you leave the shell.
+  Give root password for maintenance
+  (or type Control-D for normal startup):
+
+  [root@uml /root]# fsck -y /dev/fhd0
+  fsck -y /dev/fhd0
+  Parallelizing fsck version 1.14 (9-Jan-1999)
+  e2fsck 1.14, 9-Jan-1999 for EXT2 FS 0.5b, 95/08/09
+  /dev/fhd0 contains a file system with errors, check forced.
+  Pass 1: Checking inodes, blocks, and sizes
+  Error reading block 86894 (Attempt to read block from filesystem resulted in short read) while reading indirect blocks of inode 19780.  Ignore error? yes
+
+  Inode 19780, i_blocks is 1548, should be 540.  Fix? yes
+
+  Pass 2: Checking directory structure
+  Error reading block 49405 (Attempt to read block from filesystem resulted in short read).  Ignore error? yes
+
+  Directory inode 11858, block 0, offset 0: directory corrupted
+  Salvage? yes
+
+  Missing '.' in directory inode 11858.
+  Fix? yes
+
+  Missing '..' in directory inode 11858.
+  Fix? yes
+
+
+
+
+
+  The standard drill in this sort of situation is to fire up gdb on the
+  signal thread, which, in this case, was pid 1935.  In another window,
+  I run gdb and attach pid 1935.
+
+
+
+
+       ~/linux/2.3.26/um 1016: gdb linux
+       GNU gdb 4.17.0.11 with Linux support
+       Copyright 1998 Free Software Foundation, Inc.
+       GDB is free software, covered by the GNU General Public License, and you are
+       welcome to change it and/or distribute copies of it under certain conditions.
+       Type "show copying" to see the conditions.
+       There is absolutely no warranty for GDB.  Type "show warranty" for details.
+       This GDB was configured as "i386-redhat-linux"...
+
+       (gdb) att 1935
+       Attaching to program `/home/dike/linux/2.3.26/um/linux', Pid 1935
+       0x100756d9 in __wait4 ()
+
+
+
+
+
+
+  Let's see what's currently running:
+
+
+
+       (gdb) p current_task.pid
+       $1 = 0
+
+
+
+
+
+  It's the idle thread, which means that fsck went to sleep for some
+  reason and never woke up.
+
+
+  Let's guess that the last process in the process list is fsck:
+
+
+
+       (gdb) p current_task.prev_task.comm
+       $13 = "fsck.ext2\000\000\000\000\000\000"
+
+
+
+
+
+  It is, so let's see what it thinks it's up to:
+
+
+
+       (gdb) p current_task.prev_task.thread
+       $14 = {extern_pid = 1980, tracing = 0, want_tracing = 0, forking = 0,
+         kernel_stack_page = 0, signal_stack = 1342627840, syscall = {id = 4, args = {
+             3, 134973440, 1024, 0, 1024}, have_result = 0, result = 50590720},
+         request = {op = 2, u = {exec = {ip = 1350467584, sp = 2952789424}, fork = {
+               regs = {1350467584, 2952789424, 0 <repeats 15 times>}, sigstack = 0,
+               pid = 0}, switch_to = 0x507e8000, thread = {proc = 0x507e8000,
+               arg = 0xaffffdb0, flags = 0, new_pid = 0}, input_request = {
+               op = 1350467584, fd = -1342177872, proc = 0, pid = 0}}}}
+
+
+
+
+
+  The interesting things here are the fact that its .thread.syscall.id
+  is __NR_write (see the big switch in arch/um/kernel/syscall_kern.c or
+  the defines in include/asm-um/arch/unistd.h), and that it never
+  returned.  Also, its .request.op is OP_SWITCH (see
+  arch/um/include/user_util.h).  These mean that it went into a write,
+  and, for some reason, called schedule().
+
+
+  The fact that it never returned from write means that its stack should
+  be fairly interesting.  Its pid is 1980 (.thread.extern_pid).  That
+  process is being ptraced by the signal thread, so it must be detached
+  before gdb can attach it:
+
+
+
+
+
+
+
+
+
+
+  (gdb) call detach(1980)
+
+  Program received signal SIGSEGV, Segmentation fault.
+  <function called from gdb>
+  The program being debugged stopped while in a function called from GDB.
+  When the function (detach) is done executing, GDB will silently
+  stop (instead of continuing to evaluate the expression containing
+  the function call).
+  (gdb) call detach(1980)
+  $15 = 0
+
+
+
+
+
+  The first detach segfaults for some reason, and the second one
+  succeeds.
+
+
+  Now I detach from the signal thread, attach to the fsck thread, and
+  look at its stack:
+
+
+       (gdb) det
+       Detaching from program: /home/dike/linux/2.3.26/um/linux Pid 1935
+       (gdb) att 1980
+       Attaching to program `/home/dike/linux/2.3.26/um/linux', Pid 1980
+       0x10070451 in __kill ()
+       (gdb) bt
+       #0  0x10070451 in __kill ()
+       #1  0x10068ccd in usr1_pid (pid=1980) at process.c:30
+       #2  0x1006a03f in _switch_to (prev=0x50072000, next=0x507e8000)
+           at process_kern.c:156
+       #3  0x1006a052 in switch_to (prev=0x50072000, next=0x507e8000, last=0x50072000)
+           at process_kern.c:161
+       #4  0x10001d12 in schedule () at core.c:777
+       #5  0x1006a744 in __down (sem=0x507d241c) at semaphore.c:71
+       #6  0x1006aa10 in __down_failed () at semaphore.c:157
+       #7  0x1006c5d8 in segv_handler (sc=0x5006e940) at trap_user.c:174
+       #8  0x1006c5ec in kern_segv_handler (sig=11) at trap_user.c:182
+       #9  <signal handler called>
+       #10 0x10155404 in errno ()
+       #11 0x1006c0aa in segv (address=1342179328, is_write=2) at trap_kern.c:50
+       #12 0x1006c5d8 in segv_handler (sc=0x5006eaf8) at trap_user.c:174
+       #13 0x1006c5ec in kern_segv_handler (sig=11) at trap_user.c:182
+       #14 <signal handler called>
+       #15 0xc0fd in ?? ()
+       #16 0x10016647 in sys_write (fd=3,
+           buf=0x80b8800 <Address 0x80b8800 out of bounds>, count=1024)
+           at read_write.c:159
+       #17 0x1006d5b3 in execute_syscall (syscall=4, args=0x5006ef08)
+           at syscall_kern.c:254
+       #18 0x1006af87 in really_do_syscall (sig=12) at syscall_user.c:35
+       #19 <signal handler called>
+       #20 0x400dc8b0 in ?? ()
+
+
+
+
+
+  The interesting things here are :
+
+  o  There are two segfaults on this stack (frames 9 and 14)
+
+  o  The first faulting address (frame 11) is 0x50000800
+
+  (gdb) p (void *)1342179328
+  $16 = (void *) 0x50000800
+
+
+
+
+
+  The initial faulting address is interesting because it is on the idle
+  thread's stack.  I had been seeing the idle thread segfault for no
+  apparent reason, and the cause looked like stack corruption.  In hopes
+  of catching the culprit in the act, I had turned off all protections
+  to that stack while the idle thread wasn't running.  This apparently
+  tripped that trap.
+
+
+  However, the more immediate problem is that second segfault and I'm
+  going to concentrate on that.  First, I want to see where the fault
+  happened, so I have to go look at the sigcontent struct in frame 8:
+
+
+
+       (gdb) up
+       #1  0x10068ccd in usr1_pid (pid=1980) at process.c:30
+       30        kill(pid, SIGUSR1);
+       (gdb)
+       #2  0x1006a03f in _switch_to (prev=0x50072000, next=0x507e8000)
+           at process_kern.c:156
+       156       usr1_pid(getpid());
+       (gdb)
+       #3  0x1006a052 in switch_to (prev=0x50072000, next=0x507e8000, last=0x50072000)
+           at process_kern.c:161
+       161       _switch_to(prev, next);
+       (gdb)
+       #4  0x10001d12 in schedule () at core.c:777
+       777             switch_to(prev, next, prev);
+       (gdb)
+       #5  0x1006a744 in __down (sem=0x507d241c) at semaphore.c:71
+       71                      schedule();
+       (gdb)
+       #6  0x1006aa10 in __down_failed () at semaphore.c:157
+       157     }
+       (gdb)
+       #7  0x1006c5d8 in segv_handler (sc=0x5006e940) at trap_user.c:174
+       174       segv(sc->cr2, sc->err & 2);
+       (gdb)
+       #8  0x1006c5ec in kern_segv_handler (sig=11) at trap_user.c:182
+       182       segv_handler(sc);
+       (gdb) p *sc
+       Cannot access memory at address 0x0.
+
+
+
+
+  That's not very useful, so I'll try a more manual method:
+
+
+       (gdb) p *((struct sigcontext *) (&sig + 1))
+       $19 = {gs = 0, __gsh = 0, fs = 0, __fsh = 0, es = 43, __esh = 0, ds = 43,
+         __dsh = 0, edi = 1342179328, esi = 1350378548, ebp = 1342630440,
+         esp = 1342630420, ebx = 1348150624, edx = 1280, ecx = 0, eax = 0,
+         trapno = 14, err = 4, eip = 268480945, cs = 35, __csh = 0, eflags = 66118,
+         esp_at_signal = 1342630420, ss = 43, __ssh = 0, fpstate = 0x0, oldmask = 0,
+         cr2 = 1280}
+
+
+
+  The ip is in handle_mm_fault:
+
+
+       (gdb) p (void *)268480945
+       $20 = (void *) 0x1000b1b1
+       (gdb) i sym $20
+       handle_mm_fault + 57 in section .text
+
+
+
+
+
+  Specifically, it's in pte_alloc:
+
+
+       (gdb) i line *$20
+       Line 124 of "/home/dike/linux/2.3.26/um/include/asm/pgalloc.h"
+          starts at address 0x1000b1b1 <handle_mm_fault+57>
+          and ends at 0x1000b1b7 <handle_mm_fault+63>.
+
+
+
+
+
+  To find where in handle_mm_fault this is, I'll jump forward in the
+  code until I see an address in that procedure:
+
+
+
+       (gdb) i line *0x1000b1c0
+       Line 126 of "/home/dike/linux/2.3.26/um/include/asm/pgalloc.h"
+          starts at address 0x1000b1b7 <handle_mm_fault+63>
+          and ends at 0x1000b1c3 <handle_mm_fault+75>.
+       (gdb) i line *0x1000b1d0
+       Line 131 of "/home/dike/linux/2.3.26/um/include/asm/pgalloc.h"
+          starts at address 0x1000b1d0 <handle_mm_fault+88>
+          and ends at 0x1000b1da <handle_mm_fault+98>.
+       (gdb) i line *0x1000b1e0
+       Line 61 of "/home/dike/linux/2.3.26/um/include/asm/pgalloc.h"
+          starts at address 0x1000b1da <handle_mm_fault+98>
+          and ends at 0x1000b1e1 <handle_mm_fault+105>.
+       (gdb) i line *0x1000b1f0
+       Line 134 of "/home/dike/linux/2.3.26/um/include/asm/pgalloc.h"
+          starts at address 0x1000b1f0 <handle_mm_fault+120>
+          and ends at 0x1000b200 <handle_mm_fault+136>.
+       (gdb) i line *0x1000b200
+       Line 135 of "/home/dike/linux/2.3.26/um/include/asm/pgalloc.h"
+          starts at address 0x1000b200 <handle_mm_fault+136>
+          and ends at 0x1000b208 <handle_mm_fault+144>.
+       (gdb) i line *0x1000b210
+       Line 139 of "/home/dike/linux/2.3.26/um/include/asm/pgalloc.h"
+          starts at address 0x1000b210 <handle_mm_fault+152>
+          and ends at 0x1000b219 <handle_mm_fault+161>.
+       (gdb) i line *0x1000b220
+       Line 1168 of "memory.c" starts at address 0x1000b21e <handle_mm_fault+166>
+          and ends at 0x1000b222 <handle_mm_fault+170>.
+
+
+
+
+
+  Something is apparently wrong with the page tables or vma_structs, so
+  lets go back to frame 11 and have a look at them:
+
+
+
+  #11 0x1006c0aa in segv (address=1342179328, is_write=2) at trap_kern.c:50
+  50        handle_mm_fault(current, vma, address, is_write);
+  (gdb) call pgd_offset_proc(vma->vm_mm, address)
+  $22 = (pgd_t *) 0x80a548c
+
+
+
+
+
+  That's pretty bogus.  Page tables aren't supposed to be in process
+  text or data areas.  Let's see what's in the vma:
+
+
+       (gdb) p *vma
+       $23 = {vm_mm = 0x507d2434, vm_start = 0, vm_end = 134512640,
+         vm_next = 0x80a4f8c, vm_page_prot = {pgprot = 0}, vm_flags = 31200,
+         vm_avl_height = 2058, vm_avl_left = 0x80a8c94, vm_avl_right = 0x80d1000,
+         vm_next_share = 0xaffffdb0, vm_pprev_share = 0xaffffe63,
+         vm_ops = 0xaffffe7a, vm_pgoff = 2952789626, vm_file = 0xafffffec,
+         vm_private_data = 0x62}
+       (gdb) p *vma.vm_mm
+       $24 = {mmap = 0x507d2434, mmap_avl = 0x0, mmap_cache = 0x8048000,
+         pgd = 0x80a4f8c, mm_users = {counter = 0}, mm_count = {counter = 134904288},
+         map_count = 134909076, mmap_sem = {count = {counter = 135073792},
+           sleepers = -1342177872, wait = {lock = <optimized out or zero length>,
+             task_list = {next = 0xaffffe63, prev = 0xaffffe7a},
+             __magic = -1342177670, __creator = -1342177300}, __magic = 98},
+         page_table_lock = {}, context = 138, start_code = 0, end_code = 0,
+         start_data = 0, end_data = 0, start_brk = 0, brk = 0, start_stack = 0,
+         arg_start = 0, arg_end = 0, env_start = 0, env_end = 0, rss = 1350381536,
+         total_vm = 0, locked_vm = 0, def_flags = 0, cpu_vm_mask = 0, swap_cnt = 0,
+         swap_address = 0, segments = 0x0}
+
+
+
+
+
+  This also pretty bogus.  With all of the 0x80xxxxx and 0xaffffxxx
+  addresses, this is looking like a stack was plonked down on top of
+  these structures.  Maybe it's a stack overflow from the next page:
+
+
+
+       (gdb) p vma
+       $25 = (struct vm_area_struct *) 0x507d2434
+
+
+
+
+
+  That's towards the lower quarter of the page, so that would have to
+  have been pretty heavy stack overflow:
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+  (gdb) x/100x $25
+  0x507d2434:     0x507d2434      0x00000000      0x08048000      0x080a4f8c
+  0x507d2444:     0x00000000      0x080a79e0      0x080a8c94      0x080d1000
+  0x507d2454:     0xaffffdb0      0xaffffe63      0xaffffe7a      0xaffffe7a
+  0x507d2464:     0xafffffec      0x00000062      0x0000008a      0x00000000
+  0x507d2474:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2484:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2494:     0x00000000      0x00000000      0x507d2fe0      0x00000000
+  0x507d24a4:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d24b4:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d24c4:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d24d4:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d24e4:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d24f4:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2504:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2514:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2524:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2534:     0x00000000      0x00000000      0x507d25dc      0x00000000
+  0x507d2544:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2554:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2564:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2574:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2584:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d2594:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d25a4:     0x00000000      0x00000000      0x00000000      0x00000000
+  0x507d25b4:     0x00000000      0x00000000      0x00000000      0x00000000
+
+
+
+
+
+  It's not stack overflow.  The only "stack-like" piece of this data is
+  the vma_struct itself.
+
+
+  At this point, I don't see any avenues to pursue, so I just have to
+  admit that I have no idea what's going on.  What I will do, though, is
+  stick a trap on the segfault handler which will stop if it sees any
+  writes to the idle thread's stack.  That was the thing that happened
+  first, and it may be that if I can catch it immediately, what's going
+  on will be somewhat clearer.
+
+
+  12.2.  Episode 2: The case of the hung fsck
+
+  After setting a trap in the SEGV handler for accesses to the signal
+  thread's stack, I reran the kernel.
+
+
+  fsck hung again, this time by hitting the trap:
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+  Setting hostname uml                            [ OK ]
+  Checking root filesystem
+  /dev/fhd0 contains a file system with errors, check forced.
+  Error reading block 86894 (Attempt to read block from filesystem resulted in short read) while reading indirect blocks of inode 19780.
+
+  /dev/fhd0: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
+          (i.e., without -a or -p options)
+  [ FAILED ]
+
+  *** An error occurred during the file system check.
+  *** Dropping you to a shell; the system will reboot
+  *** when you leave the shell.
+  Give root password for maintenance
+  (or type Control-D for normal startup):
+
+  [root@uml /root]# fsck -y /dev/fhd0
+  fsck -y /dev/fhd0
+  Parallelizing fsck version 1.14 (9-Jan-1999)
+  e2fsck 1.14, 9-Jan-1999 for EXT2 FS 0.5b, 95/08/09
+  /dev/fhd0 contains a file system with errors, check forced.
+  Pass 1: Checking inodes, blocks, and sizes
+  Error reading block 86894 (Attempt to read block from filesystem resulted in short read) while reading indirect blocks of inode 19780.  Ignore error? yes
+
+  Pass 2: Checking directory structure
+  Error reading block 49405 (Attempt to read block from filesystem resulted in short read).  Ignore error? yes
+
+  Directory inode 11858, block 0, offset 0: directory corrupted
+  Salvage? yes
+
+  Missing '.' in directory inode 11858.
+  Fix? yes
+
+  Missing '..' in directory inode 11858.
+  Fix? yes
+
+  Untested (4127) [100fe44c]: trap_kern.c line 31
+
+
+
+
+
+  I need to get the signal thread to detach from pid 4127 so that I can
+  attach to it with gdb.  This is done by sending it a SIGUSR1, which is
+  caught by the signal thread, which detaches the process:
+
+
+       kill -USR1 4127
+
+
+
+
+
+  Now I can run gdb on it:
+
+
+
+
+
+
+
+
+
+
+
+
+
+  ~/linux/2.3.26/um 1034: gdb linux
+  GNU gdb 4.17.0.11 with Linux support
+  Copyright 1998 Free Software Foundation, Inc.
+  GDB is free software, covered by the GNU General Public License, and you are
+  welcome to change it and/or distribute copies of it under certain conditions.
+  Type "show copying" to see the conditions.
+  There is absolutely no warranty for GDB.  Type "show warranty" for details.
+  This GDB was configured as "i386-redhat-linux"...
+  (gdb) att 4127
+  Attaching to program `/home/dike/linux/2.3.26/um/linux', Pid 4127
+  0x10075891 in __libc_nanosleep ()
+
+
+
+
+
+  The backtrace shows that it was in a write and that the fault address
+  (address in frame 3) is 0x50000800, which is right in the middle of
+  the signal thread's stack page:
+
+
+       (gdb) bt
+       #0  0x10075891 in __libc_nanosleep ()
+       #1  0x1007584d in __sleep (seconds=1000000)
+           at ../sysdeps/unix/sysv/linux/sleep.c:78
+       #2  0x1006ce9a in stop () at user_util.c:191
+       #3  0x1006bf88 in segv (address=1342179328, is_write=2) at trap_kern.c:31
+       #4  0x1006c628 in segv_handler (sc=0x5006eaf8) at trap_user.c:174
+       #5  0x1006c63c in kern_segv_handler (sig=11) at trap_user.c:182
+       #6  <signal handler called>
+       #7  0xc0fd in ?? ()
+       #8  0x10016647 in sys_write (fd=3, buf=0x80b8800 "R.", count=1024)
+           at read_write.c:159
+       #9  0x1006d603 in execute_syscall (syscall=4, args=0x5006ef08)
+           at syscall_kern.c:254
+       #10 0x1006af87 in really_do_syscall (sig=12) at syscall_user.c:35
+       #11 <signal handler called>
+       #12 0x400dc8b0 in ?? ()
+       #13 <signal handler called>
+       #14 0x400dc8b0 in ?? ()
+       #15 0x80545fd in ?? ()
+       #16 0x804daae in ?? ()
+       #17 0x8054334 in ?? ()
+       #18 0x804d23e in ?? ()
+       #19 0x8049632 in ?? ()
+       #20 0x80491d2 in ?? ()
+       #21 0x80596b5 in ?? ()
+       (gdb) p (void *)1342179328
+       $3 = (void *) 0x50000800
+
+
+
+
+
+  Going up the stack to the segv_handler frame and looking at where in
+  the code the access happened shows that it happened near line 110 of
+  block_dev.c:
+
+
+
+
+
+
+
+
+
+  (gdb) up
+  #1  0x1007584d in __sleep (seconds=1000000)
+      at ../sysdeps/unix/sysv/linux/sleep.c:78
+  ../sysdeps/unix/sysv/linux/sleep.c:78: No such file or directory.
+  (gdb)
+  #2  0x1006ce9a in stop () at user_util.c:191
+  191       while(1) sleep(1000000);
+  (gdb)
+  #3  0x1006bf88 in segv (address=1342179328, is_write=2) at trap_kern.c:31
+  31          KERN_UNTESTED();
+  (gdb)
+  #4  0x1006c628 in segv_handler (sc=0x5006eaf8) at trap_user.c:174
+  174       segv(sc->cr2, sc->err & 2);
+  (gdb) p *sc
+  $1 = {gs = 0, __gsh = 0, fs = 0, __fsh = 0, es = 43, __esh = 0, ds = 43,
+    __dsh = 0, edi = 1342179328, esi = 134973440, ebp = 1342631484,
+    esp = 1342630864, ebx = 256, edx = 0, ecx = 256, eax = 1024, trapno = 14,
+    err = 6, eip = 268550834, cs = 35, __csh = 0, eflags = 66070,
+    esp_at_signal = 1342630864, ss = 43, __ssh = 0, fpstate = 0x0, oldmask = 0,
+    cr2 = 1342179328}
+  (gdb) p (void *)268550834
+  $2 = (void *) 0x1001c2b2
+  (gdb) i sym $2
+  block_write + 1090 in section .text
+  (gdb) i line *$2
+  Line 209 of "/home/dike/linux/2.3.26/um/include/asm/arch/string.h"
+     starts at address 0x1001c2a1 <block_write+1073>
+     and ends at 0x1001c2bf <block_write+1103>.
+  (gdb) i line *0x1001c2c0
+  Line 110 of "block_dev.c" starts at address 0x1001c2bf <block_write+1103>
+     and ends at 0x1001c2e3 <block_write+1139>.
+
+
+
+
+
+  Looking at the source shows that the fault happened during a call to
+  copy_from_user to copy the data into the kernel:
+
+
+       107             count -= chars;
+       108             copy_from_user(p,buf,chars);
+       109             p += chars;
+       110             buf += chars;
+
+
+
+
+
+  p is the pointer which must contain 0x50000800, since buf contains
+  0x80b8800 (frame 8 above).  It is defined as:
+
+
+                       p = offset + bh->b_data;
+
+
+
+
+
+  I need to figure out what bh is, and it just so happens that bh is
+  passed as an argument to mark_buffer_uptodate and mark_buffer_dirty a
+  few lines later, so I do a little disassembly:
+
+
+
+
+  (gdb) disas 0x1001c2bf 0x1001c2e0
+  Dump of assembler code from 0x1001c2bf to 0x1001c2d0:
+  0x1001c2bf <block_write+1103>:  addl   %eax,0xc(%ebp)
+  0x1001c2c2 <block_write+1106>:  movl   0xfffffdd4(%ebp),%edx
+  0x1001c2c8 <block_write+1112>:  btsl   $0x0,0x18(%edx)
+  0x1001c2cd <block_write+1117>:  btsl   $0x1,0x18(%edx)
+  0x1001c2d2 <block_write+1122>:  sbbl   %ecx,%ecx
+  0x1001c2d4 <block_write+1124>:  testl  %ecx,%ecx
+  0x1001c2d6 <block_write+1126>:  jne    0x1001c2e3 <block_write+1139>
+  0x1001c2d8 <block_write+1128>:  pushl  $0x0
+  0x1001c2da <block_write+1130>:  pushl  %edx
+  0x1001c2db <block_write+1131>:  call   0x1001819c <__mark_buffer_dirty>
+  End of assembler dump.
+
+
+
+
+
+  At that point, bh is in %edx (address 0x1001c2da), which is calculated
+  at 0x1001c2c2 as %ebp + 0xfffffdd4, so I figure exactly what that is,
+  taking %ebp from the sigcontext_struct above:
+
+
+       (gdb) p (void *)1342631484
+       $5 = (void *) 0x5006ee3c
+       (gdb) p 0x5006ee3c+0xfffffdd4
+       $6 = 1342630928
+       (gdb) p (void *)$6
+       $7 = (void *) 0x5006ec10
+       (gdb) p *((void **)$7)
+       $8 = (void *) 0x50100200
+
+
+
+
+
+  Now, I look at the structure to see what's in it, and particularly,
+  what its b_data field contains:
+
+
+       (gdb) p *((struct buffer_head *)0x50100200)
+       $13 = {b_next = 0x50289380, b_blocknr = 49405, b_size = 1024, b_list = 0,
+         b_dev = 15872, b_count = {counter = 1}, b_rdev = 15872, b_state = 24,
+         b_flushtime = 0, b_next_free = 0x501001a0, b_prev_free = 0x50100260,
+         b_this_page = 0x501001a0, b_reqnext = 0x0, b_pprev = 0x507fcf58,
+         b_data = 0x50000800 "", b_page = 0x50004000,
+         b_end_io = 0x10017f60 <end_buffer_io_sync>, b_dev_id = 0x0,
+         b_rsector = 98810, b_wait = {lock = <optimized out or zero length>,
+           task_list = {next = 0x50100248, prev = 0x50100248}, __magic = 1343226448,
+           __creator = 0}, b_kiobuf = 0x0}
+
+
+
+
+
+  The b_data field is indeed 0x50000800, so the question becomes how
+  that happened.  The rest of the structure looks fine, so this probably
+  is not a case of data corruption.  It happened on purpose somehow.
+
+
+  The b_page field is a pointer to the page_struct representing the
+  0x50000000 page.  Looking at it shows the kernel's idea of the state
+  of that page:
+
+
+
+  (gdb) p *$13.b_page
+  $17 = {list = {next = 0x50004a5c, prev = 0x100c5174}, mapping = 0x0,
+    index = 0, next_hash = 0x0, count = {counter = 1}, flags = 132, lru = {
+      next = 0x50008460, prev = 0x50019350}, wait = {
+      lock = <optimized out or zero length>, task_list = {next = 0x50004024,
+        prev = 0x50004024}, __magic = 1342193708, __creator = 0},
+    pprev_hash = 0x0, buffers = 0x501002c0, virtual = 1342177280,
+    zone = 0x100c5160}
+
+
+
+
+
+  Some sanity-checking: the virtual field shows the "virtual" address of
+  this page, which in this kernel is the same as its "physical" address,
+  and the page_struct itself should be mem_map[0], since it represents
+  the first page of memory:
+
+
+
+       (gdb) p (void *)1342177280
+       $18 = (void *) 0x50000000
+       (gdb) p mem_map
+       $19 = (mem_map_t *) 0x50004000
+
+
+
+
+
+  These check out fine.
+
+
+  Now to check out the page_struct itself.  In particular, the flags
+  field shows whether the page is considered free or not:
+
+
+       (gdb) p (void *)132
+       $21 = (void *) 0x84
+
+
+
+
+
+  The "reserved" bit is the high bit, which is definitely not set, so
+  the kernel considers the signal stack page to be free and available to
+  be used.
+
+
+  At this point, I jump to conclusions and start looking at my early
+  boot code, because that's where that page is supposed to be reserved.
+
+
+  In my setup_arch procedure, I have the following code which looks just
+  fine:
+
+
+
+       bootmap_size = init_bootmem(start_pfn, end_pfn - start_pfn);
+       free_bootmem(__pa(low_physmem) + bootmap_size, high_physmem - low_physmem);
+
+
+
+
+
+  Two stack pages have already been allocated, and low_physmem points to
+  the third page, which is the beginning of free memory.
+  The init_bootmem call declares the entire memory to the boot memory
+  manager, which marks it all reserved.  The free_bootmem call frees up
+  all of it, except for the first two pages.  This looks correct to me.
+
+
+  So, I decide to see init_bootmem run and make sure that it is marking
+  those first two pages as reserved.  I never get that far.
+
+
+  Stepping into init_bootmem, and looking at bootmem_map before looking
+  at what it contains shows the following:
+
+
+
+       (gdb) p bootmem_map
+       $3 = (void *) 0x50000000
+
+
+
+
+
+  Aha!  The light dawns.  That first page is doing double duty as a
+  stack and as the boot memory map.  The last thing that the boot memory
+  manager does is to free the pages used by its memory map, so this page
+  is getting freed even its marked as reserved.
+
+
+  The fix was to initialize the boot memory manager before allocating
+  those two stack pages, and then allocate them through the boot memory
+  manager.  After doing this, and fixing a couple of subsequent buglets,
+  the stack corruption problem disappeared.
+
+
+
+
+
+  13.  What to do when UML doesn't work
+
+
+
+
+  13.1.  Strange compilation errors when you build from source
+
+  As of test11, it is necessary to have "ARCH=um" in the environment or
+  on the make command line for all steps in building UML, including
+  clean, distclean, or mrproper, config, menuconfig, or xconfig, dep,
+  and linux.  If you forget for any of them, the i386 build seems to
+  contaminate the UML build.  If this happens, start from scratch with
+
+
+       host%
+       make mrproper ARCH=um
+
+
+
+
+  and repeat the build process with ARCH=um on all the steps.
+
+
+  See ``Compiling the kernel and modules''  for more details.
+
+
+  Another cause of strange compilation errors is building UML in
+  /usr/src/linux.  If you do this, the first thing you need to do is
+  clean up the mess you made.  The /usr/src/linux/asm link will now
+  point to /usr/src/linux/asm-um.  Make it point back to
+  /usr/src/linux/asm-i386.  Then, move your UML pool someplace else and
+  build it there.  Also see below, where a more specific set of symptoms
+  is described.
+
+
+
+  13.3.  A variety of panics and hangs with /tmp on a reiserfs  filesys-
+  tem
+
+  I saw this on reiserfs 3.5.21 and it seems to be fixed in 3.5.27.
+  Panics preceded by
+
+
+       Detaching pid nnnn
+
+
+
+  are diagnostic of this problem.  This is a reiserfs bug which causes a
+  thread to occasionally read stale data from a mmapped page shared with
+  another thread.  The fix is to upgrade the filesystem or to have /tmp
+  be an ext2 filesystem.
+
+
+
+  13.4.  The compile fails with errors about conflicting types for
+  'open', 'dup', and 'waitpid'
+
+  This happens when you build in /usr/src/linux.  The UML build makes
+  the include/asm link point to include/asm-um.  /usr/include/asm points
+  to /usr/src/linux/include/asm, so when that link gets moved, files
+  which need to include the asm-i386 versions of headers get the
+  incompatible asm-um versions.  The fix is to move the include/asm link
+  back to include/asm-i386 and to do UML builds someplace else.
+
+
+
+  13.5.  UML doesn't work when /tmp is an NFS filesystem
+
+  This seems to be a similar situation with the ReiserFS problem above.
+  Some versions of NFS seems not to handle mmap correctly, which UML
+  depends on.  The workaround is have /tmp be a non-NFS directory.
+
+
+  13.6.  UML hangs on boot when compiled with gprof support
+
+  If you build UML with gprof support and, early in the boot, it does
+  this
+
+
+       kernel BUG at page_alloc.c:100!
+
+
+
+
+  you have a buggy gcc.  You can work around the problem by removing
+  UM_FASTCALL from CFLAGS in arch/um/Makefile-i386.  This will open up
+  another bug, but that one is fairly hard to reproduce.
+
+
+
+  13.7.  syslogd dies with a SIGTERM on startup
+
+  The exact boot error depends on the distribution that you're booting,
+  but Debian produces this:
+
+
+       /etc/rc2.d/S10sysklogd: line 49:    93 Terminated
+       start-stop-daemon --start --quiet --exec /sbin/syslogd -- $SYSLOGD
+
+
+
+
+  This is a syslogd bug.  There's a race between a parent process
+  installing a signal handler and its child sending the signal.  See
+  this uml-devel post <http://www.geocrawler.com/lists/3/Source-
+  Forge/709/0/6612801>  for the details.
+
+
+
+  13.8.  TUN/TAP networking doesn't work on a 2.4 host
+
+  There are a couple of problems which were
+  <http://www.geocrawler.com/lists/3/SourceForge/597/0/> name="pointed
+  out">  by Tim Robinson <timro at trkr dot net>
+
+  o  It doesn't work on hosts running 2.4.7 (or thereabouts) or earlier.
+     The fix is to upgrade to something more recent and then read the
+     next item.
+
+  o  If you see
+
+
+       File descriptor in bad state
+
+
+
+  when you bring up the device inside UML, you have a header mismatch
+  between the original kernel and the upgraded one.  Make /usr/src/linux
+  point at the new headers.  This will only be a problem if you build
+  uml_net yourself.
+
+
+
+  13.9.  You can network to the host but not to other machines on the
+  net
+
+  If you can connect to the host, and the host can connect to UML, but
+  you cannot connect to any other machines, then you may need to enable
+  IP Masquerading on the host.  Usually this is only experienced when
+  using private IP addresses (192.168.x.x or 10.x.x.x) for host/UML
+  networking, rather than the public address space that your host is
+  connected to.  UML does not enable IP Masquerading, so you will need
+  to create a static rule to enable it:
+
+
+       host%
+       iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
+
+
+
+
+  Replace eth0 with the interface that you use to talk to the rest of
+  the world.
+
+
+  Documentation on IP Masquerading, and SNAT, can be found at
+  www.netfilter.org  <http://www.netfilter.org> .
+
+
+  If you can reach the local net, but not the outside Internet, then
+  that is usually a routing problem.  The UML needs a default route:
+
+
+       UML#
+       route add default gw gateway IP
+
+
+
+
+  The gateway IP can be any machine on the local net that knows how to
+  reach the outside world.  Usually, this is the host or the local net-
+  work's gateway.
+
+
+  Occasionally, we hear from someone who can reach some machines, but
+  not others on the same net, or who can reach some ports on other
+  machines, but not others.  These are usually caused by strange
+  firewalling somewhere between the UML and the other box.  You track
+  this down by running tcpdump on every interface the packets travel
+  over and see where they disappear.  When you find a machine that takes
+  the packets in, but does not send them onward, that's the culprit.
+
+
+
+  13.10.  I have no root and I want to scream
+
+  Thanks to Birgit Wahlich for telling me about this strange one.  It
+  turns out that there's a limit of six environment variables on the
+  kernel command line.  When that limit is reached or exceeded, argument
+  processing stops, which means that the 'root=' argument that UML
+  usually adds is not seen.  So, the filesystem has no idea what the
+  root device is, so it panics.
+
+
+  The fix is to put less stuff on the command line.  Glomming all your
+  setup variables into one is probably the best way to go.
+
+
+
+  13.11.  UML build conflict between ptrace.h and ucontext.h
+
+  On some older systems, /usr/include/asm/ptrace.h and
+  /usr/include/sys/ucontext.h define the same names.  So, when they're
+  included together, the defines from one completely mess up the parsing
+  of the other, producing errors like:
+       /usr/include/sys/ucontext.h:47: parse error before
+       `10'
+
+
+
+
+  plus a pile of warnings.
+
+
+  This is a libc botch, which has since been fixed, and I don't see any
+  way around it besides upgrading.
+
+
+
+  13.12.  The UML BogoMips is exactly half the host's BogoMips
+
+  On i386 kernels, there are two ways of running the loop that is used
+  to calculate the BogoMips rating, using the TSC if it's there or using
+  a one-instruction loop.  The TSC produces twice the BogoMips as the
+  loop.  UML uses the loop, since it has nothing resembling a TSC, and
+  will get almost exactly the same BogoMips as a host using the loop.
+  However, on a host with a TSC, its BogoMips will be double the loop
+  BogoMips, and therefore double the UML BogoMips.
+
+
+
+  13.13.  When you run UML, it immediately segfaults
+
+  If the host is configured with the 2G/2G address space split, that's
+  why.  See ``UML on 2G/2G hosts''  for the details on getting UML to
+  run on your host.
+
+
+
+  13.14.  xterms appear, then immediately disappear
+
+  If you're running an up to date kernel with an old release of
+  uml_utilities, the port-helper program will not work properly, so
+  xterms will exit straight after they appear. The solution is to
+  upgrade to the latest release of uml_utilities.  Usually this problem
+  occurs when you have installed a packaged release of UML then compiled
+  your own development kernel without upgrading the uml_utilities from
+  the source distribution.
+
+
+
+  13.15.  Any other panic, hang, or strange behavior
+
+  If you're seeing truly strange behavior, such as hangs or panics that
+  happen in random places, or you try running the debugger to see what's
+  happening and it acts strangely, then it could be a problem in the
+  host kernel.  If you're not running a stock Linus or -ac kernel, then
+  try that.  An early version of the preemption patch and a 2.4.10 SuSE
+  kernel have caused very strange problems in UML.
+
+
+  Otherwise, let me know about it.  Send a message to one of the UML
+  mailing lists - either the developer list - user-mode-linux-devel at
+  lists dot sourceforge dot net (subscription info) or the user list -
+  user-mode-linux-user at lists dot sourceforge do net (subscription
+  info), whichever you prefer.  Don't assume that everyone knows about
+  it and that a fix is imminent.
+
+
+  If you want to be super-helpful, read ``Diagnosing Problems'' and
+  follow the instructions contained therein.
+  14.  Diagnosing Problems
+
+
+  If you get UML to crash, hang, or otherwise misbehave, you should
+  report this on one of the project mailing lists, either the developer
+  list - user-mode-linux-devel at lists dot sourceforge dot net
+  (subscription info) or the user list - user-mode-linux-user at lists
+  dot sourceforge dot net (subscription info).  When you do, it is
+  likely that I will want more information.  So, it would be helpful to
+  read the stuff below, do whatever is applicable in your case, and
+  report the results to the list.
+
+
+  For any diagnosis, you're going to need to build a debugging kernel.
+  The binaries from this site aren't debuggable.  If you haven't done
+  this before, read about ``Compiling the kernel and modules''  and
+  ``Kernel debugging''  UML first.
+
+
+  14.1.  Case 1 : Normal kernel panics
+
+  The most common case is for a normal thread to panic.  To debug this,
+  you will need to run it under the debugger (add 'debug' to the command
+  line).  An xterm will start up with gdb running inside it.  Continue
+  it when it stops in start_kernel and make it crash.  Now ^C gdb and
+
+
+  If the panic was a "Kernel mode fault", then there will be a segv
+  frame on the stack and I'm going to want some more information.  The
+  stack might look something like this:
+
+
+       (UML gdb)  backtrace
+       #0  0x1009bf76 in __sigprocmask (how=1, set=0x5f347940, oset=0x0)
+           at ../sysdeps/unix/sysv/linux/sigprocmask.c:49
+       #1  0x10091411 in change_sig (signal=10, on=1) at process.c:218
+       #2  0x10094785 in timer_handler (sig=26) at time_kern.c:32
+       #3  0x1009bf38 in __restore ()
+           at ../sysdeps/unix/sysv/linux/i386/sigaction.c:125
+       #4  0x1009534c in segv (address=8, ip=268849158, is_write=2, is_user=0)
+           at trap_kern.c:66
+       #5  0x10095c04 in segv_handler (sig=11) at trap_user.c:285
+       #6  0x1009bf38 in __restore ()
+
+
+
+
+  I'm going to want to see the symbol and line information for the value
+  of ip in the segv frame.  In this case, you would do the following:
+
+
+       (UML gdb)  i sym 268849158
+
+
+
+
+  and
+
+
+       (UML gdb)  i line *268849158
+
+
+
+
+  The reason for this is the __restore frame right above the segv_han-
+  dler frame is hiding the frame that actually segfaulted.  So, I have
+  to get that information from the faulting ip.
+
+
+  14.2.  Case 2 : Tracing thread panics
+
+  The less common and more painful case is when the tracing thread
+  panics.  In this case, the kernel debugger will be useless because it
+  needs a healthy tracing thread in order to work.  The first thing to
+  do is get a backtrace from the tracing thread.  This is done by
+  figuring out what its pid is, firing up gdb, and attaching it to that
+  pid.  You can figure out the tracing thread pid by looking at the
+  first line of the console output, which will look like this:
+
+
+       tracing thread pid = 15851
+
+
+
+
+  or by running ps on the host and finding the line that looks like
+  this:
+
+
+       jdike 15851 4.5 0.4 132568 1104 pts/0 S 21:34 0:05 ./linux [(tracing thread)]
+
+
+
+
+  If the panic was 'segfault in signals', then follow the instructions
+  above for collecting information about the location of the seg fault.
+
+
+  If the tracing thread flaked out all by itself, then send that
+  backtrace in and wait for our crack debugging team to fix the problem.
+
+
+  14.3.  Case 3 : Tracing thread panics caused by other threads
+
+  However, there are cases where the misbehavior of another thread
+  caused the problem.  The most common panic of this type is:
+
+
+       wait_for_stop failed to wait for  <pid>  to stop with  <signal number>
+
+
+
+
+  In this case, you'll need to get a backtrace from the process men-
+  tioned in the panic, which is complicated by the fact that the kernel
+  debugger is defunct and without some fancy footwork, another gdb can't
+  attach to it.  So, this is how the fancy footwork goes:
+
+  In a shell:
+
+
+       host% kill -STOP pid
+
+
+
+
+  Run gdb on the tracing thread as described in case 2 and do:
+
+
+       (host gdb)  call detach(pid)
+
+
+  If you get a segfault, do it again.  It always works the second time.
+
+  Detach from the tracing thread and attach to that other thread:
+
+
+       (host gdb)  detach
+
+
+
+
+
+
+       (host gdb)  attach pid
+
+
+
+
+  If gdb hangs when attaching to that process, go back to a shell and
+  do:
+
+
+       host%
+       kill -CONT pid
+
+
+
+
+  And then get the backtrace:
+
+
+       (host gdb)  backtrace
+
+
+
+
+
+  14.4.  Case 4 : Hangs
+
+  Hangs seem to be fairly rare, but they sometimes happen.  When a hang
+  happens, we need a backtrace from the offending process.  Run the
+  kernel debugger as described in case 1 and get a backtrace.  If the
+  current process is not the idle thread, then send in the backtrace.
+  You can tell that it's the idle thread if the stack looks like this:
+
+
+       #0  0x100b1401 in __libc_nanosleep ()
+       #1  0x100a2885 in idle_sleep (secs=10) at time.c:122
+       #2  0x100a546f in do_idle () at process_kern.c:445
+       #3  0x100a5508 in cpu_idle () at process_kern.c:471
+       #4  0x100ec18f in start_kernel () at init/main.c:592
+       #5  0x100a3e10 in start_kernel_proc (unused=0x0) at um_arch.c:71
+       #6  0x100a383f in signal_tramp (arg=0x100a3dd8) at trap_user.c:50
+
+
+
+
+  If this is the case, then some other process is at fault, and went to
+  sleep when it shouldn't have.  Run ps on the host and figure out which
+  process should not have gone to sleep and stayed asleep.  Then attach
+  to it with gdb and get a backtrace as described in case 3.
+
+
+
+
+
+
+  15.  Thanks
+
+
+  A number of people have helped this project in various ways, and this
+  page gives recognition where recognition is due.
+
+
+  If you're listed here and you would prefer a real link on your name,
+  or no link at all, instead of the despammed email address pseudo-link,
+  let me know.
+
+
+  If you're not listed here and you think maybe you should be, please
+  let me know that as well.  I try to get everyone, but sometimes my
+  bookkeeping lapses and I forget about contributions.
+
+
+  15.1.  Code and Documentation
+
+  Rusty Russell <rusty at linuxcare.com.au>  -
+
+  o  wrote the  HOWTO <http://user-mode-
+     linux.sourceforge.net/UserModeLinux-HOWTO.html>
+
+  o  prodded me into making this project official and putting it on
+     SourceForge
+
+  o  came up with the way cool UML logo <http://user-mode-
+     linux.sourceforge.net/uml-small.png>
+
+  o  redid the config process
+
+
+  Peter Moulder <reiter at netspace.net.au>  - Fixed my config and build
+  processes, and added some useful code to the block driver
+
+
+  Bill Stearns <wstearns at pobox.com>  -
+
+  o  HOWTO updates
+
+  o  lots of bug reports
+
+  o  lots of testing
+
+  o  dedicated a box (uml.ists.dartmouth.edu) to support UML development
+
+  o  wrote the mkrootfs script, which allows bootable filesystems of
+     RPM-based distributions to be cranked out
+
+  o  cranked out a large number of filesystems with said script
+
+
+  Jim Leu <jleu at mindspring.com>  - Wrote the virtual ethernet driver
+  and associated usermode tools
+
+  Lars Brinkhoff <http://lars.nocrew.org/>  - Contributed the ptrace
+  proxy from his own  project <http://a386.nocrew.org/> to allow easier
+  kernel debugging
+
+
+  Andrea Arcangeli <andrea at suse.de>  - Redid some of the early boot
+  code so that it would work on machines with Large File Support
+
+
+  Chris Emerson <http://www.chiark.greenend.org.uk/~cemerson/>  - Did
+  the first UML port to Linux/ppc
+
+
+  Harald Welte <laforge at gnumonks.org>  - Wrote the multicast
+  transport for the network driver
+
+
+  Jorgen Cederlof - Added special file support to hostfs
+
+
+  Greg Lonnon  <glonnon at ridgerun dot com>  - Changed the ubd driver
+  to allow it to layer a COW file on a shared read-only filesystem and
+  wrote the iomem emulation support
+
+
+  Henrik Nordstrom <http://hem.passagen.se/hno/>  - Provided a variety
+  of patches, fixes, and clues
+
+
+  Lennert Buytenhek - Contributed various patches, a rewrite of the
+  network driver, the first implementation of the mconsole driver, and
+  did the bulk of the work needed to get SMP working again.
+
+
+  Yon Uriarte - Fixed the TUN/TAP network backend while I slept.
+
+
+  Adam Heath - Made a bunch of nice cleanups to the initialization code,
+  plus various other small patches.
+
+
+  Matt Zimmerman - Matt volunteered to be the UML Debian maintainer and
+  is doing a real nice job of it.  He also noticed and fixed a number of
+  actually and potentially exploitable security holes in uml_net.  Plus
+  the occasional patch.  I like patches.
+
+
+  James McMechan - James seems to have taken over maintenance of the ubd
+  driver and is doing a nice job of it.
+
+
+  Chandan Kudige - wrote the umlgdb script which automates the reloading
+  of module symbols.
+
+
+  Steve Schmidtke - wrote the UML slirp transport and hostaudio drivers,
+  enabling UML processes to access audio devices on the host. He also
+  submitted patches for the slip transport and lots of other things.
+
+
+  David Coulson <http://davidcoulson.net>  -
+
+  o  Set up the usermodelinux.org <http://usermodelinux.org>  site,
+     which is a great way of keeping the UML user community on top of
+     UML goings-on.
+
+  o  Site documentation and updates
+
+  o  Nifty little UML management daemon  UMLd
+     <http://uml.openconsultancy.com/umld/>
+
+  o  Lots of testing and bug reports
+
+
+
+
+  15.2.  Flushing out bugs
+
+
+
+  o  Yuri Pudgorodsky
+
+  o  Gerald Britton
+
+  o  Ian Wehrman
+
+  o  Gord Lamb
+
+  o  Eugene Koontz
+
+  o  John H. Hartman
+
+  o  Anders Karlsson
+
+  o  Daniel Phillips
+
+  o  John Fremlin
+
+  o  Rainer Burgstaller
+
+  o  James Stevenson
+
+  o  Matt Clay
+
+  o  Cliff Jefferies
+
+  o  Geoff Hoff
+
+  o  Lennert Buytenhek
+
+  o  Al Viro
+
+  o  Frank Klingenhoefer
+
+  o  Livio Baldini Soares
+
+  o  Jon Burgess
+
+  o  Petru Paler
+
+  o  Paul
+
+  o  Chris Reahard
+
+  o  Sverker Nilsson
+
+  o  Gong Su
+
+  o  johan verrept
+
+  o  Bjorn Eriksson
+
+  o  Lorenzo Allegrucci
+
+  o  Muli Ben-Yehuda
+
+  o  David Mansfield
+
+  o  Howard Goff
+
+  o  Mike Anderson
+
+  o  John Byrne
+
+  o  Sapan J. Batia
+
+  o  Iris Huang
+
+  o  Jan Hudec
+
+  o  Voluspa
+
+
+
+
+  15.3.  Buglets and clean-ups
+
+
+
+  o  Dave Zarzycki
+
+  o  Adam Lazur
+
+  o  Boria Feigin
+
+  o  Brian J. Murrell
+
+  o  JS
+
+  o  Roman Zippel
+
+  o  Wil Cooley
+
+  o  Ayelet Shemesh
+
+  o  Will Dyson
+
+  o  Sverker Nilsson
+
+  o  dvorak
+
+  o  v.naga srinivas
+
+  o  Shlomi Fish
+
+  o  Roger Binns
+
+  o  johan verrept
+
+  o  MrChuoi
+
+  o  Peter Cleve
+
+  o  Vincent Guffens
+
+  o  Nathan Scott
+
+  o  Patrick Caulfield
+
+  o  jbearce
+
+  o  Catalin Marinas
+
+  o  Shane Spencer
+
+  o  Zou Min
+
+
+  o  Ryan Boder
+
+  o  Lorenzo Colitti
+
+  o  Gwendal Grignou
+
+  o  Andre' Breiler
+
+  o  Tsutomu Yasuda
+
+
+
+  15.4.  Case Studies
+
+
+  o  Jon Wright
+
+  o  William McEwan
+
+  o  Michael Richardson
+
+
+
+  15.5.  Other contributions
+
+
+  Bill Carr <Bill.Carr at compaq.com>  made the Red Hat mkrootfs script
+  work with RH 6.2.
+
+  Michael Jennings <mikejen at hevanet.com>  sent in some material which
+  is now gracing the top of the  index  page <http://user-mode-
+  linux.sourceforge.net/>  of this site.
+
+  SGI <http://www.sgi.com>  (and more specifically Ralf Baechle <ralf at
+  uni-koblenz.de> ) gave me an account on oss.sgi.com
+  <http://www.oss.sgi.com> .  The bandwidth there made it possible to
+  produce most of the filesystems available on the project download
+  page.
+
+  Laurent Bonnaud <Laurent.Bonnaud at inpg.fr>  took the old grotty
+  Debian filesystem that I've been distributing and updated it to 2.2.
+  It is now available by itself here.
+
+  Rik van Riel gave me some ftp space on ftp.nl.linux.org so I can make
+  releases even when Sourceforge is broken.
+
+  Rodrigo de Castro looked at my broken pte code and told me what was
+  wrong with it, letting me fix a long-standing (several weeks) and
+  serious set of bugs.
+
+  Chris Reahard built a specialized root filesystem for running a DNS
+  server jailed inside UML.  It's available from the download
+  <http://user-mode-linux.sourceforge.net/dl-sf.html>  page in the Jail
+  Filesystems section.
+
+
+
+
+
+
+
+
+
+
+
+