v4.19.13 snapshot.
diff --git a/include/linux/power/ab8500.h b/include/linux/power/ab8500.h
new file mode 100644
index 0000000..cdbb6c2
--- /dev/null
+++ b/include/linux/power/ab8500.h
@@ -0,0 +1,16 @@
+/*
+ * Copyright (C) ST-Ericsson 2013
+ * Author: Hongbo Zhang <hongbo.zhang@linaro.com>
+ * License terms: GNU General Public License v2
+ */
+
+#ifndef PWR_AB8500_H
+#define PWR_AB8500_H
+
+extern const struct abx500_res_to_temp ab8500_temp_tbl_a_thermistor[];
+extern const int ab8500_temp_tbl_a_size;
+
+extern const struct abx500_res_to_temp ab8500_temp_tbl_b_thermistor[];
+extern const int ab8500_temp_tbl_b_size;
+
+#endif /* PWR_AB8500_H */
diff --git a/include/linux/power/bq2415x_charger.h b/include/linux/power/bq2415x_charger.h
new file mode 100644
index 0000000..50762af
--- /dev/null
+++ b/include/linux/power/bq2415x_charger.h
@@ -0,0 +1,58 @@
+/*
+ * bq2415x charger driver
+ *
+ * Copyright (C) 2011-2013 Pali Rohár <pali.rohar@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#ifndef BQ2415X_CHARGER_H
+#define BQ2415X_CHARGER_H
+
+/*
+ * This is platform data for bq2415x chip. It contains default board
+ * voltages and currents which can be also later configured via sysfs. If
+ * value is -1 then default chip value (specified in datasheet) will be
+ * used.
+ *
+ * Value resistor_sense is needed for for configuring charge and
+ * termination current. It it is less or equal to zero, configuring charge
+ * and termination current will not be possible.
+ *
+ * For automode support is needed to provide name of power supply device
+ * in value notify_device. Device driver must immediately report property
+ * POWER_SUPPLY_PROP_CURRENT_MAX when current changed.
+ */
+
+/* Supported modes with maximal current limit */
+enum bq2415x_mode {
+ BQ2415X_MODE_OFF, /* offline mode (charger disabled) */
+ BQ2415X_MODE_NONE, /* unknown charger (100mA) */
+ BQ2415X_MODE_HOST_CHARGER, /* usb host/hub charger (500mA) */
+ BQ2415X_MODE_DEDICATED_CHARGER, /* dedicated charger (unlimited) */
+ BQ2415X_MODE_BOOST, /* boost mode (charging disabled) */
+};
+
+struct bq2415x_platform_data {
+ int current_limit; /* mA */
+ int weak_battery_voltage; /* mV */
+ int battery_regulation_voltage; /* mV */
+ int charge_current; /* mA */
+ int termination_current; /* mA */
+ int resistor_sense; /* m ohm */
+ const char *notify_device; /* name */
+};
+
+#endif
diff --git a/include/linux/power/bq24190_charger.h b/include/linux/power/bq24190_charger.h
new file mode 100644
index 0000000..45ce7f1
--- /dev/null
+++ b/include/linux/power/bq24190_charger.h
@@ -0,0 +1,18 @@
+/*
+ * Platform data for the TI bq24190 battery charger driver.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _BQ24190_CHARGER_H_
+#define _BQ24190_CHARGER_H_
+
+#include <linux/regulator/machine.h>
+
+struct bq24190_platform_data {
+ const struct regulator_init_data *regulator_init_data;
+};
+
+#endif
diff --git a/include/linux/power/bq24735-charger.h b/include/linux/power/bq24735-charger.h
new file mode 100644
index 0000000..b04be59
--- /dev/null
+++ b/include/linux/power/bq24735-charger.h
@@ -0,0 +1,37 @@
+/*
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __CHARGER_BQ24735_H_
+#define __CHARGER_BQ24735_H_
+
+#include <linux/types.h>
+#include <linux/power_supply.h>
+
+struct bq24735_platform {
+ uint32_t charge_current;
+ uint32_t charge_voltage;
+ uint32_t input_current;
+
+ const char *name;
+
+ bool ext_control;
+
+ char **supplied_to;
+ size_t num_supplicants;
+};
+
+#endif /* __CHARGER_BQ24735_H_ */
diff --git a/include/linux/power/bq27xxx_battery.h b/include/linux/power/bq27xxx_battery.h
new file mode 100644
index 0000000..d6355f4
--- /dev/null
+++ b/include/linux/power/bq27xxx_battery.h
@@ -0,0 +1,79 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __LINUX_BQ27X00_BATTERY_H__
+#define __LINUX_BQ27X00_BATTERY_H__
+
+enum bq27xxx_chip {
+ BQ27000 = 1, /* bq27000, bq27200 */
+ BQ27010, /* bq27010, bq27210 */
+ BQ2750X, /* bq27500 deprecated alias */
+ BQ2751X, /* bq27510, bq27520 deprecated alias */
+ BQ2752X,
+ BQ27500, /* bq27500/1 */
+ BQ27510G1, /* bq27510G1 */
+ BQ27510G2, /* bq27510G2 */
+ BQ27510G3, /* bq27510G3 */
+ BQ27520G1, /* bq27520G1 */
+ BQ27520G2, /* bq27520G2 */
+ BQ27520G3, /* bq27520G3 */
+ BQ27520G4, /* bq27520G4 */
+ BQ27521, /* bq27521 */
+ BQ27530, /* bq27530, bq27531 */
+ BQ27531,
+ BQ27541, /* bq27541, bq27542, bq27546, bq27742 */
+ BQ27542,
+ BQ27546,
+ BQ27742,
+ BQ27545, /* bq27545 */
+ BQ27421, /* bq27421, bq27441, bq27621 */
+ BQ27425,
+ BQ27426,
+ BQ27441,
+ BQ27621,
+};
+
+struct bq27xxx_device_info;
+struct bq27xxx_access_methods {
+ int (*read)(struct bq27xxx_device_info *di, u8 reg, bool single);
+ int (*write)(struct bq27xxx_device_info *di, u8 reg, int value, bool single);
+ int (*read_bulk)(struct bq27xxx_device_info *di, u8 reg, u8 *data, int len);
+ int (*write_bulk)(struct bq27xxx_device_info *di, u8 reg, u8 *data, int len);
+};
+
+struct bq27xxx_reg_cache {
+ int temperature;
+ int time_to_empty;
+ int time_to_empty_avg;
+ int time_to_full;
+ int charge_full;
+ int cycle_count;
+ int capacity;
+ int energy;
+ int flags;
+ int power_avg;
+ int health;
+};
+
+struct bq27xxx_device_info {
+ struct device *dev;
+ int id;
+ enum bq27xxx_chip chip;
+ u32 opts;
+ const char *name;
+ struct bq27xxx_dm_reg *dm_regs;
+ u32 unseal_key;
+ struct bq27xxx_access_methods bus;
+ struct bq27xxx_reg_cache cache;
+ int charge_design_full;
+ unsigned long last_update;
+ struct delayed_work work;
+ struct power_supply *bat;
+ struct list_head list;
+ struct mutex lock;
+ u8 *regs;
+};
+
+void bq27xxx_battery_update(struct bq27xxx_device_info *di);
+int bq27xxx_battery_setup(struct bq27xxx_device_info *di);
+void bq27xxx_battery_teardown(struct bq27xxx_device_info *di);
+
+#endif
diff --git a/include/linux/power/charger-manager.h b/include/linux/power/charger-manager.h
new file mode 100644
index 0000000..c4fa907
--- /dev/null
+++ b/include/linux/power/charger-manager.h
@@ -0,0 +1,259 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics Co., Ltd.
+ * MyungJoo.Ham <myungjoo.ham@samsung.com>
+ *
+ * Charger Manager.
+ * This framework enables to control and multiple chargers and to
+ * monitor charging even in the context of suspend-to-RAM with
+ * an interface combining the chargers.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+**/
+
+#ifndef _CHARGER_MANAGER_H
+#define _CHARGER_MANAGER_H
+
+#include <linux/power_supply.h>
+#include <linux/extcon.h>
+#include <linux/alarmtimer.h>
+
+enum data_source {
+ CM_BATTERY_PRESENT,
+ CM_NO_BATTERY,
+ CM_FUEL_GAUGE,
+ CM_CHARGER_STAT,
+};
+
+enum polling_modes {
+ CM_POLL_DISABLE = 0,
+ CM_POLL_ALWAYS,
+ CM_POLL_EXTERNAL_POWER_ONLY,
+ CM_POLL_CHARGING_ONLY,
+};
+
+enum cm_event_types {
+ CM_EVENT_UNKNOWN = 0,
+ CM_EVENT_BATT_FULL,
+ CM_EVENT_BATT_IN,
+ CM_EVENT_BATT_OUT,
+ CM_EVENT_BATT_OVERHEAT,
+ CM_EVENT_BATT_COLD,
+ CM_EVENT_EXT_PWR_IN_OUT,
+ CM_EVENT_CHG_START_STOP,
+ CM_EVENT_OTHERS,
+};
+
+/**
+ * struct charger_cable
+ * @extcon_name: the name of extcon device.
+ * @name: the name of charger cable(external connector).
+ * @extcon_dev: the extcon device.
+ * @wq: the workqueue to control charger according to the state of
+ * charger cable. If charger cable is attached, enable charger.
+ * But if charger cable is detached, disable charger.
+ * @nb: the notifier block to receive changed state from EXTCON
+ * (External Connector) when charger cable is attached/detached.
+ * @attached: the state of charger cable.
+ * true: the charger cable is attached
+ * false: the charger cable is detached
+ * @charger: the instance of struct charger_regulator.
+ * @cm: the Charger Manager representing the battery.
+ */
+struct charger_cable {
+ const char *extcon_name;
+ const char *name;
+
+ /* The charger-manager use Extcon framework */
+ struct extcon_specific_cable_nb extcon_dev;
+ struct work_struct wq;
+ struct notifier_block nb;
+
+ /* The state of charger cable */
+ bool attached;
+
+ struct charger_regulator *charger;
+
+ /*
+ * Set min/max current of regulator to protect over-current issue
+ * according to a kind of charger cable when cable is attached.
+ */
+ int min_uA;
+ int max_uA;
+
+ struct charger_manager *cm;
+};
+
+/**
+ * struct charger_regulator
+ * @regulator_name: the name of regulator for using charger.
+ * @consumer: the regulator consumer for the charger.
+ * @externally_control:
+ * Set if the charger-manager cannot control charger,
+ * the charger will be maintained with disabled state.
+ * @cables:
+ * the array of charger cables to enable/disable charger
+ * and set current limit according to constraint data of
+ * struct charger_cable if only charger cable included
+ * in the array of charger cables is attached/detached.
+ * @num_cables: the number of charger cables.
+ * @attr_g: Attribute group for the charger(regulator)
+ * @attr_name: "name" sysfs entry
+ * @attr_state: "state" sysfs entry
+ * @attr_externally_control: "externally_control" sysfs entry
+ * @attrs: Arrays pointing to attr_name/state/externally_control for attr_g
+ */
+struct charger_regulator {
+ /* The name of regulator for charging */
+ const char *regulator_name;
+ struct regulator *consumer;
+
+ /* charger never on when system is on */
+ int externally_control;
+
+ /*
+ * Store constraint information related to current limit,
+ * each cable have different condition for charging.
+ */
+ struct charger_cable *cables;
+ int num_cables;
+
+ struct attribute_group attr_g;
+ struct device_attribute attr_name;
+ struct device_attribute attr_state;
+ struct device_attribute attr_externally_control;
+ struct attribute *attrs[4];
+
+ struct charger_manager *cm;
+};
+
+/**
+ * struct charger_desc
+ * @psy_name: the name of power-supply-class for charger manager
+ * @polling_mode:
+ * Determine which polling mode will be used
+ * @fullbatt_vchkdrop_ms:
+ * @fullbatt_vchkdrop_uV:
+ * Check voltage drop after the battery is fully charged.
+ * If it has dropped more than fullbatt_vchkdrop_uV after
+ * fullbatt_vchkdrop_ms, CM will restart charging.
+ * @fullbatt_uV: voltage in microvolt
+ * If VBATT >= fullbatt_uV, it is assumed to be full.
+ * @fullbatt_soc: state of Charge in %
+ * If state of Charge >= fullbatt_soc, it is assumed to be full.
+ * @fullbatt_full_capacity: full capacity measure
+ * If full capacity of battery >= fullbatt_full_capacity,
+ * it is assumed to be full.
+ * @polling_interval_ms: interval in millisecond at which
+ * charger manager will monitor battery health
+ * @battery_present:
+ * Specify where information for existence of battery can be obtained
+ * @psy_charger_stat: the names of power-supply for chargers
+ * @num_charger_regulator: the number of entries in charger_regulators
+ * @charger_regulators: array of charger regulators
+ * @psy_fuel_gauge: the name of power-supply for fuel gauge
+ * @thermal_zone : the name of thermal zone for battery
+ * @temp_min : Minimum battery temperature for charging.
+ * @temp_max : Maximum battery temperature for charging.
+ * @temp_diff : Temperature difference to restart charging.
+ * @measure_battery_temp:
+ * true: measure battery temperature
+ * false: measure ambient temperature
+ * @charging_max_duration_ms: Maximum possible duration for charging
+ * If whole charging duration exceed 'charging_max_duration_ms',
+ * cm stop charging.
+ * @discharging_max_duration_ms:
+ * Maximum possible duration for discharging with charger cable
+ * after full-batt. If discharging duration exceed 'discharging
+ * max_duration_ms', cm start charging.
+ */
+struct charger_desc {
+ const char *psy_name;
+
+ enum polling_modes polling_mode;
+ unsigned int polling_interval_ms;
+
+ unsigned int fullbatt_vchkdrop_ms;
+ unsigned int fullbatt_vchkdrop_uV;
+ unsigned int fullbatt_uV;
+ unsigned int fullbatt_soc;
+ unsigned int fullbatt_full_capacity;
+
+ enum data_source battery_present;
+
+ const char **psy_charger_stat;
+
+ int num_charger_regulators;
+ struct charger_regulator *charger_regulators;
+
+ const char *psy_fuel_gauge;
+
+ const char *thermal_zone;
+
+ int temp_min;
+ int temp_max;
+ int temp_diff;
+
+ bool measure_battery_temp;
+
+ u32 charging_max_duration_ms;
+ u32 discharging_max_duration_ms;
+};
+
+#define PSY_NAME_MAX 30
+
+/**
+ * struct charger_manager
+ * @entry: entry for list
+ * @dev: device pointer
+ * @desc: instance of charger_desc
+ * @fuel_gauge: power_supply for fuel gauge
+ * @charger_stat: array of power_supply for chargers
+ * @tzd_batt : thermal zone device for battery
+ * @charger_enabled: the state of charger
+ * @fullbatt_vchk_jiffies_at:
+ * jiffies at the time full battery check will occur.
+ * @fullbatt_vchk_work: work queue for full battery check
+ * @emergency_stop:
+ * When setting true, stop charging
+ * @psy_name_buf: the name of power-supply-class for charger manager
+ * @charger_psy: power_supply for charger manager
+ * @status_save_ext_pwr_inserted:
+ * saved status of external power before entering suspend-to-RAM
+ * @status_save_batt:
+ * saved status of battery before entering suspend-to-RAM
+ * @charging_start_time: saved start time of enabling charging
+ * @charging_end_time: saved end time of disabling charging
+ */
+struct charger_manager {
+ struct list_head entry;
+ struct device *dev;
+ struct charger_desc *desc;
+
+#ifdef CONFIG_THERMAL
+ struct thermal_zone_device *tzd_batt;
+#endif
+ bool charger_enabled;
+
+ unsigned long fullbatt_vchk_jiffies_at;
+ struct delayed_work fullbatt_vchk_work;
+
+ int emergency_stop;
+
+ char psy_name_buf[PSY_NAME_MAX + 1];
+ struct power_supply_desc charger_psy_desc;
+ struct power_supply *charger_psy;
+
+ u64 charging_start_time;
+ u64 charging_end_time;
+};
+
+#ifdef CONFIG_CHARGER_MANAGER
+extern void cm_notify_event(struct power_supply *psy,
+ enum cm_event_types type, char *msg);
+#else
+static inline void cm_notify_event(struct power_supply *psy,
+ enum cm_event_types type, char *msg) { }
+#endif
+#endif /* _CHARGER_MANAGER_H */
diff --git a/include/linux/power/generic-adc-battery.h b/include/linux/power/generic-adc-battery.h
new file mode 100644
index 0000000..b1ebe08
--- /dev/null
+++ b/include/linux/power/generic-adc-battery.h
@@ -0,0 +1,29 @@
+/*
+ * Copyright (C) 2012, Anish Kumar <anish198519851985@gmail.com>
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef GENERIC_ADC_BATTERY_H
+#define GENERIC_ADC_BATTERY_H
+
+/**
+ * struct gab_platform_data - platform_data for generic adc iio battery driver.
+ * @battery_info: recommended structure to specify static power supply
+ * parameters
+ * @cal_charge: calculate charge level.
+ * @gpio_charge_finished: gpio for the charger.
+ * @gpio_inverted: Should be 1 if the GPIO is active low otherwise 0
+ * @jitter_delay: delay required after the interrupt to check battery
+ * status.Default set is 10ms.
+ */
+struct gab_platform_data {
+ struct power_supply_info battery_info;
+ int (*cal_charge)(long value);
+ int gpio_charge_finished;
+ bool gpio_inverted;
+ int jitter_delay;
+};
+
+#endif /* GENERIC_ADC_BATTERY_H */
diff --git a/include/linux/power/gpio-charger.h b/include/linux/power/gpio-charger.h
new file mode 100644
index 0000000..de1dfe0
--- /dev/null
+++ b/include/linux/power/gpio-charger.h
@@ -0,0 +1,41 @@
+/*
+ * Copyright (C) 2010, Lars-Peter Clausen <lars@metafoo.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef __LINUX_POWER_GPIO_CHARGER_H__
+#define __LINUX_POWER_GPIO_CHARGER_H__
+
+#include <linux/power_supply.h>
+#include <linux/types.h>
+
+/**
+ * struct gpio_charger_platform_data - platform_data for gpio_charger devices
+ * @name: Name for the chargers power_supply device
+ * @type: Type of the charger
+ * @gpio: GPIO which is used to indicate the chargers status
+ * @gpio_active_low: Should be set to 1 if the GPIO is active low otherwise 0
+ * @supplied_to: Array of battery names to which this chargers supplies power
+ * @num_supplicants: Number of entries in the supplied_to array
+ */
+struct gpio_charger_platform_data {
+ const char *name;
+ enum power_supply_type type;
+
+ int gpio;
+ int gpio_active_low;
+
+ char **supplied_to;
+ size_t num_supplicants;
+};
+
+#endif
diff --git a/include/linux/power/isp1704_charger.h b/include/linux/power/isp1704_charger.h
new file mode 100644
index 0000000..0105d9e
--- /dev/null
+++ b/include/linux/power/isp1704_charger.h
@@ -0,0 +1,30 @@
+/*
+ * ISP1704 USB Charger Detection driver
+ *
+ * Copyright (C) 2011 Nokia Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+
+#ifndef __ISP1704_CHARGER_H
+#define __ISP1704_CHARGER_H
+
+struct isp1704_charger_data {
+ void (*set_power)(bool on);
+ int enable_gpio;
+};
+
+#endif
diff --git a/include/linux/power/jz4740-battery.h b/include/linux/power/jz4740-battery.h
new file mode 100644
index 0000000..19c9610
--- /dev/null
+++ b/include/linux/power/jz4740-battery.h
@@ -0,0 +1,24 @@
+/*
+ * Copyright (C) 2009, Jiejing Zhang <kzjeef@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef __JZ4740_BATTERY_H
+#define __JZ4740_BATTERY_H
+
+struct jz_battery_platform_data {
+ struct power_supply_info info;
+ int gpio_charge; /* GPIO port of Charger state */
+ int gpio_charge_active_low;
+};
+
+#endif
diff --git a/include/linux/power/max17042_battery.h b/include/linux/power/max17042_battery.h
new file mode 100644
index 0000000..a7ed29b
--- /dev/null
+++ b/include/linux/power/max17042_battery.h
@@ -0,0 +1,231 @@
+/*
+ * Fuel gauge driver for Maxim 17042 / 8966 / 8997
+ * Note that Maxim 8966 and 8997 are mfd and this is its subdevice.
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ * MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __MAX17042_BATTERY_H_
+#define __MAX17042_BATTERY_H_
+
+#define MAX17042_STATUS_BattAbsent (1 << 3)
+#define MAX17042_BATTERY_FULL (95) /* Recommend. FullSOCThr value */
+#define MAX17042_DEFAULT_SNS_RESISTOR (10000)
+#define MAX17042_DEFAULT_VMIN (3000)
+#define MAX17042_DEFAULT_VMAX (4500) /* LiHV cell max */
+#define MAX17042_DEFAULT_TEMP_MIN (0) /* For sys without temp sensor */
+#define MAX17042_DEFAULT_TEMP_MAX (700) /* 70 degrees Celcius */
+
+/* Consider RepCap which is less then 10 units below FullCAP full */
+#define MAX17042_FULL_THRESHOLD 10
+
+#define MAX17042_CHARACTERIZATION_DATA_SIZE 48
+
+enum max17042_register {
+ MAX17042_STATUS = 0x00,
+ MAX17042_VALRT_Th = 0x01,
+ MAX17042_TALRT_Th = 0x02,
+ MAX17042_SALRT_Th = 0x03,
+ MAX17042_AtRate = 0x04,
+ MAX17042_RepCap = 0x05,
+ MAX17042_RepSOC = 0x06,
+ MAX17042_Age = 0x07,
+ MAX17042_TEMP = 0x08,
+ MAX17042_VCELL = 0x09,
+ MAX17042_Current = 0x0A,
+ MAX17042_AvgCurrent = 0x0B,
+
+ MAX17042_SOC = 0x0D,
+ MAX17042_AvSOC = 0x0E,
+ MAX17042_RemCap = 0x0F,
+ MAX17042_FullCAP = 0x10,
+ MAX17042_TTE = 0x11,
+ MAX17042_V_empty = 0x12,
+
+ MAX17042_RSLOW = 0x14,
+
+ MAX17042_AvgTA = 0x16,
+ MAX17042_Cycles = 0x17,
+ MAX17042_DesignCap = 0x18,
+ MAX17042_AvgVCELL = 0x19,
+ MAX17042_MinMaxTemp = 0x1A,
+ MAX17042_MinMaxVolt = 0x1B,
+ MAX17042_MinMaxCurr = 0x1C,
+ MAX17042_CONFIG = 0x1D,
+ MAX17042_ICHGTerm = 0x1E,
+ MAX17042_AvCap = 0x1F,
+ MAX17042_ManName = 0x20,
+ MAX17042_DevName = 0x21,
+
+ MAX17042_FullCAPNom = 0x23,
+ MAX17042_TempNom = 0x24,
+ MAX17042_TempLim = 0x25,
+ MAX17042_TempHot = 0x26,
+ MAX17042_AIN = 0x27,
+ MAX17042_LearnCFG = 0x28,
+ MAX17042_FilterCFG = 0x29,
+ MAX17042_RelaxCFG = 0x2A,
+ MAX17042_MiscCFG = 0x2B,
+ MAX17042_TGAIN = 0x2C,
+ MAx17042_TOFF = 0x2D,
+ MAX17042_CGAIN = 0x2E,
+ MAX17042_COFF = 0x2F,
+
+ MAX17042_MaskSOC = 0x32,
+ MAX17042_SOC_empty = 0x33,
+ MAX17042_T_empty = 0x34,
+
+ MAX17042_FullCAP0 = 0x35,
+ MAX17042_LAvg_empty = 0x36,
+ MAX17042_FCTC = 0x37,
+ MAX17042_RCOMP0 = 0x38,
+ MAX17042_TempCo = 0x39,
+ MAX17042_EmptyTempCo = 0x3A,
+ MAX17042_K_empty0 = 0x3B,
+ MAX17042_TaskPeriod = 0x3C,
+ MAX17042_FSTAT = 0x3D,
+
+ MAX17042_SHDNTIMER = 0x3F,
+
+ MAX17042_dQacc = 0x45,
+ MAX17042_dPacc = 0x46,
+
+ MAX17042_VFSOC0 = 0x48,
+
+ MAX17042_QH = 0x4D,
+ MAX17042_QL = 0x4E,
+
+ MAX17042_VFSOC0Enable = 0x60,
+ MAX17042_MLOCKReg1 = 0x62,
+ MAX17042_MLOCKReg2 = 0x63,
+
+ MAX17042_MODELChrTbl = 0x80,
+
+ MAX17042_OCV = 0xEE,
+
+ MAX17042_OCVInternal = 0xFB,
+
+ MAX17042_VFSOC = 0xFF,
+};
+
+/* Registers specific to max17047/50 */
+enum max17047_register {
+ MAX17047_QRTbl00 = 0x12,
+ MAX17047_FullSOCThr = 0x13,
+ MAX17047_QRTbl10 = 0x22,
+ MAX17047_QRTbl20 = 0x32,
+ MAX17047_V_empty = 0x3A,
+ MAX17047_QRTbl30 = 0x42,
+};
+
+enum max170xx_chip_type {
+ MAXIM_DEVICE_TYPE_UNKNOWN = 0,
+ MAXIM_DEVICE_TYPE_MAX17042,
+ MAXIM_DEVICE_TYPE_MAX17047,
+ MAXIM_DEVICE_TYPE_MAX17050,
+
+ MAXIM_DEVICE_TYPE_NUM
+};
+
+/*
+ * used for setting a register to a desired value
+ * addr : address for a register
+ * data : setting value for the register
+ */
+struct max17042_reg_data {
+ u8 addr;
+ u16 data;
+};
+
+struct max17042_config_data {
+ /* External current sense resistor value in milli-ohms */
+ u32 cur_sense_val;
+
+ /* A/D measurement */
+ u16 tgain; /* 0x2C */
+ u16 toff; /* 0x2D */
+ u16 cgain; /* 0x2E */
+ u16 coff; /* 0x2F */
+
+ /* Alert / Status */
+ u16 valrt_thresh; /* 0x01 */
+ u16 talrt_thresh; /* 0x02 */
+ u16 soc_alrt_thresh; /* 0x03 */
+ u16 config; /* 0x01D */
+ u16 shdntimer; /* 0x03F */
+
+ /* App data */
+ u16 full_soc_thresh; /* 0x13 */
+ u16 design_cap; /* 0x18 */
+ u16 ichgt_term; /* 0x1E */
+
+ /* MG3 config */
+ u16 at_rate; /* 0x04 */
+ u16 learn_cfg; /* 0x28 */
+ u16 filter_cfg; /* 0x29 */
+ u16 relax_cfg; /* 0x2A */
+ u16 misc_cfg; /* 0x2B */
+ u16 masksoc; /* 0x32 */
+
+ /* MG3 save and restore */
+ u16 fullcap; /* 0x10 */
+ u16 fullcapnom; /* 0x23 */
+ u16 socempty; /* 0x33 */
+ u16 lavg_empty; /* 0x36 */
+ u16 dqacc; /* 0x45 */
+ u16 dpacc; /* 0x46 */
+ u16 qrtbl00; /* 0x12 */
+ u16 qrtbl10; /* 0x22 */
+ u16 qrtbl20; /* 0x32 */
+ u16 qrtbl30; /* 0x42 */
+
+ /* Cell technology from power_supply.h */
+ u16 cell_technology;
+
+ /* Cell Data */
+ u16 vempty; /* 0x12 */
+ u16 temp_nom; /* 0x24 */
+ u16 temp_lim; /* 0x25 */
+ u16 fctc; /* 0x37 */
+ u16 rcomp0; /* 0x38 */
+ u16 tcompc0; /* 0x39 */
+ u16 empty_tempco; /* 0x3A */
+ u16 kempty0; /* 0x3B */
+ u16 cell_char_tbl[MAX17042_CHARACTERIZATION_DATA_SIZE];
+} __packed;
+
+struct max17042_platform_data {
+ struct max17042_reg_data *init_data;
+ struct max17042_config_data *config_data;
+ int num_init_data; /* Number of enties in init_data array */
+ bool enable_current_sense;
+ bool enable_por_init; /* Use POR init from Maxim appnote */
+
+ /*
+ * R_sns in micro-ohms.
+ * default 10000 (if r_sns = 0) as it is the recommended value by
+ * the datasheet although it can be changed by board designers.
+ */
+ unsigned int r_sns;
+ int vmin; /* in millivolts */
+ int vmax; /* in millivolts */
+ int temp_min; /* in tenths of degree Celsius */
+ int temp_max; /* in tenths of degree Celsius */
+};
+
+#endif /* __MAX17042_BATTERY_H_ */
diff --git a/include/linux/power/max8903_charger.h b/include/linux/power/max8903_charger.h
new file mode 100644
index 0000000..89d3f1c
--- /dev/null
+++ b/include/linux/power/max8903_charger.h
@@ -0,0 +1,57 @@
+/*
+ * max8903_charger.h - Maxim 8903 USB/Adapter Charger Driver
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ * MyungJoo Ham <myungjoo.ham@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef __MAX8903_CHARGER_H__
+#define __MAX8903_CHARGER_H__
+
+struct max8903_pdata {
+ /*
+ * GPIOs
+ * cen, chg, flt, dcm and usus are optional.
+ * dok and uok are not optional depending on the status of
+ * dc_valid and usb_valid.
+ */
+ int cen; /* Charger Enable input */
+ int dok; /* DC(Adapter) Power OK output */
+ int uok; /* USB Power OK output */
+ int chg; /* Charger status output */
+ int flt; /* Fault output */
+ int dcm; /* Current-Limit Mode input (1: DC, 2: USB) */
+ int usus; /* USB Suspend Input (1: suspended) */
+
+ /*
+ * DC(Adapter/TA) is wired
+ * When dc_valid is true,
+ * dok should be valid.
+ *
+ * At least one of dc_valid or usb_valid should be true.
+ */
+ bool dc_valid;
+ /*
+ * USB is wired
+ * When usb_valid is true,
+ * uok should be valid.
+ */
+ bool usb_valid;
+};
+
+#endif /* __MAX8903_CHARGER_H__ */
diff --git a/include/linux/power/sbs-battery.h b/include/linux/power/sbs-battery.h
new file mode 100644
index 0000000..519b8b4
--- /dev/null
+++ b/include/linux/power/sbs-battery.h
@@ -0,0 +1,38 @@
+/*
+ * Gas Gauge driver for SBS Compliant Gas Gauges
+ *
+ * Copyright (c) 2010, NVIDIA Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
+ */
+
+#ifndef __LINUX_POWER_SBS_BATTERY_H_
+#define __LINUX_POWER_SBS_BATTERY_H_
+
+#include <linux/power_supply.h>
+#include <linux/types.h>
+
+/**
+ * struct sbs_platform_data - platform data for sbs devices
+ * @i2c_retry_count: # of times to retry on i2c IO failure
+ * @poll_retry_count: # of times to retry looking for new status after
+ * external change notification
+ */
+struct sbs_platform_data {
+ u32 i2c_retry_count;
+ u32 poll_retry_count;
+};
+
+#endif
diff --git a/include/linux/power/smartreflex.h b/include/linux/power/smartreflex.h
new file mode 100644
index 0000000..7b81dad
--- /dev/null
+++ b/include/linux/power/smartreflex.h
@@ -0,0 +1,326 @@
+/*
+ * OMAP Smartreflex Defines and Routines
+ *
+ * Author: Thara Gopinath <thara@ti.com>
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ * Thara Gopinath <thara@ti.com>
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Kalle Jokiniemi
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ * Lesly A M <x0080970@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __POWER_SMARTREFLEX_H
+#define __POWER_SMARTREFLEX_H
+
+#include <linux/types.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/platform_data/voltage-omap.h>
+
+/*
+ * Different Smartreflex IPs version. The v1 is the 65nm version used in
+ * OMAP3430. The v2 is the update for the 45nm version of the IP
+ * used in OMAP3630 and OMAP4430
+ */
+#define SR_TYPE_V1 1
+#define SR_TYPE_V2 2
+
+/* SMART REFLEX REG ADDRESS OFFSET */
+#define SRCONFIG 0x00
+#define SRSTATUS 0x04
+#define SENVAL 0x08
+#define SENMIN 0x0C
+#define SENMAX 0x10
+#define SENAVG 0x14
+#define AVGWEIGHT 0x18
+#define NVALUERECIPROCAL 0x1c
+#define SENERROR_V1 0x20
+#define ERRCONFIG_V1 0x24
+#define IRQ_EOI 0x20
+#define IRQSTATUS_RAW 0x24
+#define IRQSTATUS 0x28
+#define IRQENABLE_SET 0x2C
+#define IRQENABLE_CLR 0x30
+#define SENERROR_V2 0x34
+#define ERRCONFIG_V2 0x38
+
+/* Bit/Shift Positions */
+
+/* SRCONFIG */
+#define SRCONFIG_ACCUMDATA_SHIFT 22
+#define SRCONFIG_SRCLKLENGTH_SHIFT 12
+#define SRCONFIG_SENNENABLE_V1_SHIFT 5
+#define SRCONFIG_SENPENABLE_V1_SHIFT 3
+#define SRCONFIG_SENNENABLE_V2_SHIFT 1
+#define SRCONFIG_SENPENABLE_V2_SHIFT 0
+#define SRCONFIG_CLKCTRL_SHIFT 0
+
+#define SRCONFIG_ACCUMDATA_MASK (0x3ff << 22)
+
+#define SRCONFIG_SRENABLE BIT(11)
+#define SRCONFIG_SENENABLE BIT(10)
+#define SRCONFIG_ERRGEN_EN BIT(9)
+#define SRCONFIG_MINMAXAVG_EN BIT(8)
+#define SRCONFIG_DELAYCTRL BIT(2)
+
+/* AVGWEIGHT */
+#define AVGWEIGHT_SENPAVGWEIGHT_SHIFT 2
+#define AVGWEIGHT_SENNAVGWEIGHT_SHIFT 0
+
+/* NVALUERECIPROCAL */
+#define NVALUERECIPROCAL_SENPGAIN_SHIFT 20
+#define NVALUERECIPROCAL_SENNGAIN_SHIFT 16
+#define NVALUERECIPROCAL_RNSENP_SHIFT 8
+#define NVALUERECIPROCAL_RNSENN_SHIFT 0
+
+/* ERRCONFIG */
+#define ERRCONFIG_ERRWEIGHT_SHIFT 16
+#define ERRCONFIG_ERRMAXLIMIT_SHIFT 8
+#define ERRCONFIG_ERRMINLIMIT_SHIFT 0
+
+#define SR_ERRWEIGHT_MASK (0x07 << 16)
+#define SR_ERRMAXLIMIT_MASK (0xff << 8)
+#define SR_ERRMINLIMIT_MASK (0xff << 0)
+
+#define ERRCONFIG_VPBOUNDINTEN_V1 BIT(31)
+#define ERRCONFIG_VPBOUNDINTST_V1 BIT(30)
+#define ERRCONFIG_MCUACCUMINTEN BIT(29)
+#define ERRCONFIG_MCUACCUMINTST BIT(28)
+#define ERRCONFIG_MCUVALIDINTEN BIT(27)
+#define ERRCONFIG_MCUVALIDINTST BIT(26)
+#define ERRCONFIG_MCUBOUNDINTEN BIT(25)
+#define ERRCONFIG_MCUBOUNDINTST BIT(24)
+#define ERRCONFIG_MCUDISACKINTEN BIT(23)
+#define ERRCONFIG_VPBOUNDINTST_V2 BIT(23)
+#define ERRCONFIG_MCUDISACKINTST BIT(22)
+#define ERRCONFIG_VPBOUNDINTEN_V2 BIT(22)
+
+#define ERRCONFIG_STATUS_V1_MASK (ERRCONFIG_VPBOUNDINTST_V1 | \
+ ERRCONFIG_MCUACCUMINTST | \
+ ERRCONFIG_MCUVALIDINTST | \
+ ERRCONFIG_MCUBOUNDINTST | \
+ ERRCONFIG_MCUDISACKINTST)
+/* IRQSTATUS */
+#define IRQSTATUS_MCUACCUMINT BIT(3)
+#define IRQSTATUS_MCVALIDINT BIT(2)
+#define IRQSTATUS_MCBOUNDSINT BIT(1)
+#define IRQSTATUS_MCUDISABLEACKINT BIT(0)
+
+/* IRQENABLE_SET and IRQENABLE_CLEAR */
+#define IRQENABLE_MCUACCUMINT BIT(3)
+#define IRQENABLE_MCUVALIDINT BIT(2)
+#define IRQENABLE_MCUBOUNDSINT BIT(1)
+#define IRQENABLE_MCUDISABLEACKINT BIT(0)
+
+/* Common Bit values */
+
+#define SRCLKLENGTH_12MHZ_SYSCLK 0x3c
+#define SRCLKLENGTH_13MHZ_SYSCLK 0x41
+#define SRCLKLENGTH_19MHZ_SYSCLK 0x60
+#define SRCLKLENGTH_26MHZ_SYSCLK 0x82
+#define SRCLKLENGTH_38MHZ_SYSCLK 0xC0
+
+/*
+ * 3430 specific values. Maybe these should be passed from board file or
+ * pmic structures.
+ */
+#define OMAP3430_SR_ACCUMDATA 0x1f4
+
+#define OMAP3430_SR1_SENPAVGWEIGHT 0x03
+#define OMAP3430_SR1_SENNAVGWEIGHT 0x03
+
+#define OMAP3430_SR2_SENPAVGWEIGHT 0x01
+#define OMAP3430_SR2_SENNAVGWEIGHT 0x01
+
+#define OMAP3430_SR_ERRWEIGHT 0x04
+#define OMAP3430_SR_ERRMAXLIMIT 0x02
+
+enum sr_instance {
+ OMAP_SR_MPU, /* shared with iva on omap3 */
+ OMAP_SR_CORE,
+ OMAP_SR_IVA,
+ OMAP_SR_NR,
+};
+
+struct omap_sr {
+ char *name;
+ struct list_head node;
+ struct platform_device *pdev;
+ struct omap_sr_nvalue_table *nvalue_table;
+ struct voltagedomain *voltdm;
+ struct dentry *dbg_dir;
+ unsigned int irq;
+ int srid;
+ int ip_type;
+ int nvalue_count;
+ bool autocomp_active;
+ u32 clk_length;
+ u32 err_weight;
+ u32 err_minlimit;
+ u32 err_maxlimit;
+ u32 accum_data;
+ u32 senn_avgweight;
+ u32 senp_avgweight;
+ u32 senp_mod;
+ u32 senn_mod;
+ void __iomem *base;
+};
+
+/**
+ * test_cond_timeout - busy-loop, testing a condition
+ * @cond: condition to test until it evaluates to true
+ * @timeout: maximum number of microseconds in the timeout
+ * @index: loop index (integer)
+ *
+ * Loop waiting for @cond to become true or until at least @timeout
+ * microseconds have passed. To use, define some integer @index in the
+ * calling code. After running, if @index == @timeout, then the loop has
+ * timed out.
+ *
+ * Copied from omap_test_timeout */
+#define sr_test_cond_timeout(cond, timeout, index) \
+({ \
+ for (index = 0; index < timeout; index++) { \
+ if (cond) \
+ break; \
+ udelay(1); \
+ } \
+})
+
+/**
+ * struct omap_sr_pmic_data - Strucutre to be populated by pmic code to pass
+ * pmic specific info to smartreflex driver
+ *
+ * @sr_pmic_init: API to initialize smartreflex on the PMIC side.
+ */
+struct omap_sr_pmic_data {
+ void (*sr_pmic_init) (void);
+};
+
+/**
+ * struct omap_smartreflex_dev_attr - Smartreflex Device attribute.
+ *
+ * @sensor_voltdm_name: Name of voltdomain of SR instance
+ */
+struct omap_smartreflex_dev_attr {
+ const char *sensor_voltdm_name;
+};
+
+/*
+ * The smart reflex driver supports CLASS1 CLASS2 and CLASS3 SR.
+ * The smartreflex class driver should pass the class type.
+ * Should be used to populate the class_type field of the
+ * omap_smartreflex_class_data structure.
+ */
+#define SR_CLASS1 0x1
+#define SR_CLASS2 0x2
+#define SR_CLASS3 0x3
+
+/**
+ * struct omap_sr_class_data - Smartreflex class driver info
+ *
+ * @enable: API to enable a particular class smaartreflex.
+ * @disable: API to disable a particular class smartreflex.
+ * @configure: API to configure a particular class smartreflex.
+ * @notify: API to notify the class driver about an event in SR.
+ * Not needed for class3.
+ * @notify_flags: specify the events to be notified to the class driver
+ * @class_type: specify which smartreflex class.
+ * Can be used by the SR driver to take any class
+ * based decisions.
+ */
+struct omap_sr_class_data {
+ int (*enable)(struct omap_sr *sr);
+ int (*disable)(struct omap_sr *sr, int is_volt_reset);
+ int (*configure)(struct omap_sr *sr);
+ int (*notify)(struct omap_sr *sr, u32 status);
+ u8 notify_flags;
+ u8 class_type;
+};
+
+/**
+ * struct omap_sr_nvalue_table - Smartreflex n-target value info
+ *
+ * @efuse_offs: The offset of the efuse where n-target values are stored.
+ * @nvalue: The n-target value.
+ * @errminlimit: The value of the ERRMINLIMIT bitfield for this n-target
+ * @volt_nominal: microvolts DC that the VDD is initially programmed to
+ */
+struct omap_sr_nvalue_table {
+ u32 efuse_offs;
+ u32 nvalue;
+ u32 errminlimit;
+ unsigned long volt_nominal;
+};
+
+/**
+ * struct omap_sr_data - Smartreflex platform data.
+ *
+ * @name: instance name
+ * @ip_type: Smartreflex IP type.
+ * @senp_mod: SENPENABLE value of the sr CONFIG register
+ * @senn_mod: SENNENABLE value for sr CONFIG register
+ * @err_weight ERRWEIGHT value of the sr ERRCONFIG register
+ * @err_maxlimit ERRMAXLIMIT value of the sr ERRCONFIG register
+ * @accum_data ACCUMDATA value of the sr CONFIG register
+ * @senn_avgweight SENNAVGWEIGHT value of the sr AVGWEIGHT register
+ * @senp_avgweight SENPAVGWEIGHT value of the sr AVGWEIGHT register
+ * @nvalue_count: Number of distinct nvalues in the nvalue table
+ * @enable_on_init: whether this sr module needs to enabled at
+ * boot up or not.
+ * @nvalue_table: table containing the efuse offsets and nvalues
+ * corresponding to them.
+ * @voltdm: Pointer to the voltage domain associated with the SR
+ */
+struct omap_sr_data {
+ const char *name;
+ int ip_type;
+ u32 senp_mod;
+ u32 senn_mod;
+ u32 err_weight;
+ u32 err_maxlimit;
+ u32 accum_data;
+ u32 senn_avgweight;
+ u32 senp_avgweight;
+ int nvalue_count;
+ bool enable_on_init;
+ struct omap_sr_nvalue_table *nvalue_table;
+ struct voltagedomain *voltdm;
+};
+
+#ifdef CONFIG_POWER_AVS_OMAP
+
+/* Smartreflex module enable/disable interface */
+void omap_sr_enable(struct voltagedomain *voltdm);
+void omap_sr_disable(struct voltagedomain *voltdm);
+void omap_sr_disable_reset_volt(struct voltagedomain *voltdm);
+
+/* API to register the pmic specific data with the smartreflex driver. */
+void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data);
+
+/* Smartreflex driver hooks to be called from Smartreflex class driver */
+int sr_enable(struct omap_sr *sr, unsigned long volt);
+void sr_disable(struct omap_sr *sr);
+int sr_configure_errgen(struct omap_sr *sr);
+int sr_disable_errgen(struct omap_sr *sr);
+int sr_configure_minmax(struct omap_sr *sr);
+
+/* API to register the smartreflex class driver with the smartreflex driver */
+int sr_register_class(struct omap_sr_class_data *class_data);
+#else
+static inline void omap_sr_enable(struct voltagedomain *voltdm) {}
+static inline void omap_sr_disable(struct voltagedomain *voltdm) {}
+static inline void omap_sr_disable_reset_volt(
+ struct voltagedomain *voltdm) {}
+static inline void omap_sr_register_pmic(
+ struct omap_sr_pmic_data *pmic_data) {}
+#endif
+#endif
diff --git a/include/linux/power/smb347-charger.h b/include/linux/power/smb347-charger.h
new file mode 100644
index 0000000..b3cb20d
--- /dev/null
+++ b/include/linux/power/smb347-charger.h
@@ -0,0 +1,117 @@
+/*
+ * Summit Microelectronics SMB347 Battery Charger Driver
+ *
+ * Copyright (C) 2011, Intel Corporation
+ *
+ * Authors: Bruce E. Robertson <bruce.e.robertson@intel.com>
+ * Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef SMB347_CHARGER_H
+#define SMB347_CHARGER_H
+
+#include <linux/types.h>
+#include <linux/power_supply.h>
+
+enum {
+ /* use the default compensation method */
+ SMB347_SOFT_TEMP_COMPENSATE_DEFAULT = -1,
+
+ SMB347_SOFT_TEMP_COMPENSATE_NONE,
+ SMB347_SOFT_TEMP_COMPENSATE_CURRENT,
+ SMB347_SOFT_TEMP_COMPENSATE_VOLTAGE,
+};
+
+/* Use default factory programmed value for hard/soft temperature limit */
+#define SMB347_TEMP_USE_DEFAULT -273
+
+/*
+ * Charging enable can be controlled by software (via i2c) by
+ * smb347-charger driver or by EN pin (active low/high).
+ */
+enum smb347_chg_enable {
+ SMB347_CHG_ENABLE_SW,
+ SMB347_CHG_ENABLE_PIN_ACTIVE_LOW,
+ SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH,
+};
+
+/**
+ * struct smb347_charger_platform_data - platform data for SMB347 charger
+ * @battery_info: Information about the battery
+ * @max_charge_current: maximum current (in uA) the battery can be charged
+ * @max_charge_voltage: maximum voltage (in uV) the battery can be charged
+ * @pre_charge_current: current (in uA) to use in pre-charging phase
+ * @termination_current: current (in uA) used to determine when the
+ * charging cycle terminates
+ * @pre_to_fast_voltage: voltage (in uV) treshold used for transitioning to
+ * pre-charge to fast charge mode
+ * @mains_current_limit: maximum input current drawn from AC/DC input (in uA)
+ * @usb_hc_current_limit: maximum input high current (in uA) drawn from USB
+ * input
+ * @chip_temp_threshold: die temperature where device starts limiting charge
+ * current [%100 - %130] (in degree C)
+ * @soft_cold_temp_limit: soft cold temperature limit [%0 - %15] (in degree C),
+ * granularity is 5 deg C.
+ * @soft_hot_temp_limit: soft hot temperature limit [%40 - %55] (in degree C),
+ * granularity is 5 deg C.
+ * @hard_cold_temp_limit: hard cold temperature limit [%-5 - %10] (in degree C),
+ * granularity is 5 deg C.
+ * @hard_hot_temp_limit: hard hot temperature limit [%50 - %65] (in degree C),
+ * granularity is 5 deg C.
+ * @suspend_on_hard_temp_limit: suspend charging when hard limit is hit
+ * @soft_temp_limit_compensation: compensation method when soft temperature
+ * limit is hit
+ * @charge_current_compensation: current (in uA) for charging compensation
+ * current when temperature hits soft limits
+ * @use_mains: AC/DC input can be used
+ * @use_usb: USB input can be used
+ * @use_usb_otg: USB OTG output can be used (not implemented yet)
+ * @irq_gpio: GPIO number used for interrupts (%-1 if not used)
+ * @enable_control: how charging enable/disable is controlled
+ * (driver/pin controls)
+ *
+ * @use_main, @use_usb, and @use_usb_otg are means to enable/disable
+ * hardware support for these. This is useful when we want to have for
+ * example OTG charging controlled via OTG transceiver driver and not by
+ * the SMB347 hardware.
+ *
+ * Hard and soft temperature limit values are given as described in the
+ * device data sheet and assuming NTC beta value is %3750. Even if this is
+ * not the case, these values should be used. They can be mapped to the
+ * corresponding NTC beta values with the help of table %2 in the data
+ * sheet. So for example if NTC beta is %3375 and we want to program hard
+ * hot limit to be %53 deg C, @hard_hot_temp_limit should be set to %50.
+ *
+ * If zero value is given in any of the current and voltage values, the
+ * factory programmed default will be used. For soft/hard temperature
+ * values, pass in %SMB347_TEMP_USE_DEFAULT instead.
+ */
+struct smb347_charger_platform_data {
+ struct power_supply_info battery_info;
+ unsigned int max_charge_current;
+ unsigned int max_charge_voltage;
+ unsigned int pre_charge_current;
+ unsigned int termination_current;
+ unsigned int pre_to_fast_voltage;
+ unsigned int mains_current_limit;
+ unsigned int usb_hc_current_limit;
+ unsigned int chip_temp_threshold;
+ int soft_cold_temp_limit;
+ int soft_hot_temp_limit;
+ int hard_cold_temp_limit;
+ int hard_hot_temp_limit;
+ bool suspend_on_hard_temp_limit;
+ unsigned int soft_temp_limit_compensation;
+ unsigned int charge_current_compensation;
+ bool use_mains;
+ bool use_usb;
+ bool use_usb_otg;
+ int irq_gpio;
+ enum smb347_chg_enable enable_control;
+};
+
+#endif /* SMB347_CHARGER_H */
diff --git a/include/linux/power/twl4030_madc_battery.h b/include/linux/power/twl4030_madc_battery.h
new file mode 100644
index 0000000..23110dc
--- /dev/null
+++ b/include/linux/power/twl4030_madc_battery.h
@@ -0,0 +1,39 @@
+/*
+ * Dumb driver for LiIon batteries using TWL4030 madc.
+ *
+ * Copyright 2013 Golden Delicious Computers
+ * Nikolaus Schaller <hns@goldelico.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef __TWL4030_MADC_BATTERY_H
+#define __TWL4030_MADC_BATTERY_H
+
+/*
+ * Usually we can assume 100% @ 4.15V and 0% @ 3.3V but curves differ for
+ * charging and discharging!
+ */
+
+struct twl4030_madc_bat_calibration {
+ short voltage; /* in mV - specify -1 for end of list */
+ short level; /* in percent (0 .. 100%) */
+};
+
+struct twl4030_madc_bat_platform_data {
+ unsigned int capacity; /* total capacity in uAh */
+ struct twl4030_madc_bat_calibration *charging;
+ int charging_size;
+ struct twl4030_madc_bat_calibration *discharging;
+ int discharging_size;
+};
+
+#endif