v4.19.13 snapshot.
diff --git a/include/linux/amba/bus.h b/include/linux/amba/bus.h
new file mode 100644
index 0000000..d143c13
--- /dev/null
+++ b/include/linux/amba/bus.h
@@ -0,0 +1,181 @@
+/*
+ * linux/include/amba/bus.h
+ *
+ * This device type deals with ARM PrimeCells and anything else that
+ * presents a proper CID (0xB105F00D) at the end of the I/O register
+ * region or that is derived from a PrimeCell.
+ *
+ * Copyright (C) 2003 Deep Blue Solutions Ltd, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef ASMARM_AMBA_H
+#define ASMARM_AMBA_H
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/mod_devicetable.h>
+#include <linux/err.h>
+#include <linux/resource.h>
+#include <linux/regulator/consumer.h>
+
+#define AMBA_NR_IRQS 9
+#define AMBA_CID 0xb105f00d
+#define CORESIGHT_CID 0xb105900d
+
+struct clk;
+
+struct amba_device {
+ struct device dev;
+ struct resource res;
+ struct clk *pclk;
+ unsigned int periphid;
+ unsigned int irq[AMBA_NR_IRQS];
+ char *driver_override;
+};
+
+struct amba_driver {
+ struct device_driver drv;
+ int (*probe)(struct amba_device *, const struct amba_id *);
+ int (*remove)(struct amba_device *);
+ void (*shutdown)(struct amba_device *);
+ const struct amba_id *id_table;
+};
+
+/*
+ * Constants for the designer field of the Peripheral ID register. When bit 7
+ * is set to '1', bits [6:0] should be the JEP106 manufacturer identity code.
+ */
+enum amba_vendor {
+ AMBA_VENDOR_ARM = 0x41,
+ AMBA_VENDOR_ST = 0x80,
+ AMBA_VENDOR_QCOM = 0x51,
+ AMBA_VENDOR_LSI = 0xb6,
+ AMBA_VENDOR_LINUX = 0xfe, /* This value is not official */
+};
+
+/* This is used to generate pseudo-ID for AMBA device */
+#define AMBA_LINUX_ID(conf, rev, part) \
+ (((conf) & 0xff) << 24 | ((rev) & 0xf) << 20 | \
+ AMBA_VENDOR_LINUX << 12 | ((part) & 0xfff))
+
+extern struct bus_type amba_bustype;
+
+#define to_amba_device(d) container_of(d, struct amba_device, dev)
+
+#define amba_get_drvdata(d) dev_get_drvdata(&d->dev)
+#define amba_set_drvdata(d,p) dev_set_drvdata(&d->dev, p)
+
+int amba_driver_register(struct amba_driver *);
+void amba_driver_unregister(struct amba_driver *);
+struct amba_device *amba_device_alloc(const char *, resource_size_t, size_t);
+void amba_device_put(struct amba_device *);
+int amba_device_add(struct amba_device *, struct resource *);
+int amba_device_register(struct amba_device *, struct resource *);
+struct amba_device *amba_apb_device_add(struct device *parent, const char *name,
+ resource_size_t base, size_t size,
+ int irq1, int irq2, void *pdata,
+ unsigned int periphid);
+struct amba_device *amba_ahb_device_add(struct device *parent, const char *name,
+ resource_size_t base, size_t size,
+ int irq1, int irq2, void *pdata,
+ unsigned int periphid);
+struct amba_device *
+amba_apb_device_add_res(struct device *parent, const char *name,
+ resource_size_t base, size_t size, int irq1,
+ int irq2, void *pdata, unsigned int periphid,
+ struct resource *resbase);
+struct amba_device *
+amba_ahb_device_add_res(struct device *parent, const char *name,
+ resource_size_t base, size_t size, int irq1,
+ int irq2, void *pdata, unsigned int periphid,
+ struct resource *resbase);
+void amba_device_unregister(struct amba_device *);
+struct amba_device *amba_find_device(const char *, struct device *, unsigned int, unsigned int);
+int amba_request_regions(struct amba_device *, const char *);
+void amba_release_regions(struct amba_device *);
+
+static inline int amba_pclk_enable(struct amba_device *dev)
+{
+ return clk_enable(dev->pclk);
+}
+
+static inline void amba_pclk_disable(struct amba_device *dev)
+{
+ clk_disable(dev->pclk);
+}
+
+static inline int amba_pclk_prepare(struct amba_device *dev)
+{
+ return clk_prepare(dev->pclk);
+}
+
+static inline void amba_pclk_unprepare(struct amba_device *dev)
+{
+ clk_unprepare(dev->pclk);
+}
+
+/* Some drivers don't use the struct amba_device */
+#define AMBA_CONFIG_BITS(a) (((a) >> 24) & 0xff)
+#define AMBA_REV_BITS(a) (((a) >> 20) & 0x0f)
+#define AMBA_MANF_BITS(a) (((a) >> 12) & 0xff)
+#define AMBA_PART_BITS(a) ((a) & 0xfff)
+
+#define amba_config(d) AMBA_CONFIG_BITS((d)->periphid)
+#define amba_rev(d) AMBA_REV_BITS((d)->periphid)
+#define amba_manf(d) AMBA_MANF_BITS((d)->periphid)
+#define amba_part(d) AMBA_PART_BITS((d)->periphid)
+
+#define __AMBA_DEV(busid, data, mask) \
+ { \
+ .coherent_dma_mask = mask, \
+ .init_name = busid, \
+ .platform_data = data, \
+ }
+
+/*
+ * APB devices do not themselves have the ability to address memory,
+ * so DMA masks should be zero (much like USB peripheral devices.)
+ * The DMA controller DMA masks should be used instead (much like
+ * USB host controllers in conventional PCs.)
+ */
+#define AMBA_APB_DEVICE(name, busid, id, base, irqs, data) \
+struct amba_device name##_device = { \
+ .dev = __AMBA_DEV(busid, data, 0), \
+ .res = DEFINE_RES_MEM(base, SZ_4K), \
+ .irq = irqs, \
+ .periphid = id, \
+}
+
+/*
+ * AHB devices are DMA capable, so set their DMA masks
+ */
+#define AMBA_AHB_DEVICE(name, busid, id, base, irqs, data) \
+struct amba_device name##_device = { \
+ .dev = __AMBA_DEV(busid, data, ~0ULL), \
+ .res = DEFINE_RES_MEM(base, SZ_4K), \
+ .irq = irqs, \
+ .periphid = id, \
+}
+
+/*
+ * module_amba_driver() - Helper macro for drivers that don't do anything
+ * special in module init/exit. This eliminates a lot of boilerplate. Each
+ * module may only use this macro once, and calling it replaces module_init()
+ * and module_exit()
+ */
+#define module_amba_driver(__amba_drv) \
+ module_driver(__amba_drv, amba_driver_register, amba_driver_unregister)
+
+/*
+ * builtin_amba_driver() - Helper macro for drivers that don't do anything
+ * special in driver initcall. This eliminates a lot of boilerplate. Each
+ * driver may only use this macro once, and calling it replaces the instance
+ * device_initcall().
+ */
+#define builtin_amba_driver(__amba_drv) \
+ builtin_driver(__amba_drv, amba_driver_register)
+
+#endif
diff --git a/include/linux/amba/clcd-regs.h b/include/linux/amba/clcd-regs.h
new file mode 100644
index 0000000..516a6fd
--- /dev/null
+++ b/include/linux/amba/clcd-regs.h
@@ -0,0 +1,86 @@
+/*
+ * David A Rusling
+ *
+ * Copyright (C) 2001 ARM Limited
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive
+ * for more details.
+ */
+
+#ifndef AMBA_CLCD_REGS_H
+#define AMBA_CLCD_REGS_H
+
+/*
+ * CLCD Controller Internal Register addresses
+ */
+#define CLCD_TIM0 0x00000000
+#define CLCD_TIM1 0x00000004
+#define CLCD_TIM2 0x00000008
+#define CLCD_TIM3 0x0000000c
+#define CLCD_UBAS 0x00000010
+#define CLCD_LBAS 0x00000014
+
+#define CLCD_PL110_IENB 0x00000018
+#define CLCD_PL110_CNTL 0x0000001c
+#define CLCD_PL110_STAT 0x00000020
+#define CLCD_PL110_INTR 0x00000024
+#define CLCD_PL110_UCUR 0x00000028
+#define CLCD_PL110_LCUR 0x0000002C
+
+#define CLCD_PL111_CNTL 0x00000018
+#define CLCD_PL111_IENB 0x0000001c
+#define CLCD_PL111_RIS 0x00000020
+#define CLCD_PL111_MIS 0x00000024
+#define CLCD_PL111_ICR 0x00000028
+#define CLCD_PL111_UCUR 0x0000002c
+#define CLCD_PL111_LCUR 0x00000030
+
+#define CLCD_PALL 0x00000200
+#define CLCD_PALETTE 0x00000200
+
+#define TIM2_PCD_LO_MASK GENMASK(4, 0)
+#define TIM2_PCD_LO_BITS 5
+#define TIM2_CLKSEL (1 << 5)
+#define TIM2_IVS (1 << 11)
+#define TIM2_IHS (1 << 12)
+#define TIM2_IPC (1 << 13)
+#define TIM2_IOE (1 << 14)
+#define TIM2_BCD (1 << 26)
+#define TIM2_PCD_HI_MASK GENMASK(31, 27)
+#define TIM2_PCD_HI_BITS 5
+#define TIM2_PCD_HI_SHIFT 27
+
+#define CNTL_LCDEN (1 << 0)
+#define CNTL_LCDBPP1 (0 << 1)
+#define CNTL_LCDBPP2 (1 << 1)
+#define CNTL_LCDBPP4 (2 << 1)
+#define CNTL_LCDBPP8 (3 << 1)
+#define CNTL_LCDBPP16 (4 << 1)
+#define CNTL_LCDBPP16_565 (6 << 1)
+#define CNTL_LCDBPP16_444 (7 << 1)
+#define CNTL_LCDBPP24 (5 << 1)
+#define CNTL_LCDBW (1 << 4)
+#define CNTL_LCDTFT (1 << 5)
+#define CNTL_LCDMONO8 (1 << 6)
+#define CNTL_LCDDUAL (1 << 7)
+#define CNTL_BGR (1 << 8)
+#define CNTL_BEBO (1 << 9)
+#define CNTL_BEPO (1 << 10)
+#define CNTL_LCDPWR (1 << 11)
+#define CNTL_LCDVCOMP(x) ((x) << 12)
+#define CNTL_LDMAFIFOTIME (1 << 15)
+#define CNTL_WATERMARK (1 << 16)
+
+/* ST Microelectronics variant bits */
+#define CNTL_ST_1XBPP_444 0x0
+#define CNTL_ST_1XBPP_5551 (1 << 17)
+#define CNTL_ST_1XBPP_565 (1 << 18)
+#define CNTL_ST_CDWID_12 0x0
+#define CNTL_ST_CDWID_16 (1 << 19)
+#define CNTL_ST_CDWID_18 (1 << 20)
+#define CNTL_ST_CDWID_24 ((1 << 19)|(1 << 20))
+#define CNTL_ST_CEAEN (1 << 21)
+#define CNTL_ST_LCDBPP24_PACKED (6 << 1)
+
+#endif /* AMBA_CLCD_REGS_H */
diff --git a/include/linux/amba/clcd.h b/include/linux/amba/clcd.h
new file mode 100644
index 0000000..d0c3be7
--- /dev/null
+++ b/include/linux/amba/clcd.h
@@ -0,0 +1,321 @@
+/*
+ * linux/include/asm-arm/hardware/amba_clcd.h -- Integrator LCD panel.
+ *
+ * David A Rusling
+ *
+ * Copyright (C) 2001 ARM Limited
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive
+ * for more details.
+ */
+#include <linux/fb.h>
+#include <linux/amba/clcd-regs.h>
+
+enum {
+ /* individual formats */
+ CLCD_CAP_RGB444 = (1 << 0),
+ CLCD_CAP_RGB5551 = (1 << 1),
+ CLCD_CAP_RGB565 = (1 << 2),
+ CLCD_CAP_RGB888 = (1 << 3),
+ CLCD_CAP_BGR444 = (1 << 4),
+ CLCD_CAP_BGR5551 = (1 << 5),
+ CLCD_CAP_BGR565 = (1 << 6),
+ CLCD_CAP_BGR888 = (1 << 7),
+
+ /* connection layouts */
+ CLCD_CAP_444 = CLCD_CAP_RGB444 | CLCD_CAP_BGR444,
+ CLCD_CAP_5551 = CLCD_CAP_RGB5551 | CLCD_CAP_BGR5551,
+ CLCD_CAP_565 = CLCD_CAP_RGB565 | CLCD_CAP_BGR565,
+ CLCD_CAP_888 = CLCD_CAP_RGB888 | CLCD_CAP_BGR888,
+
+ /* red/blue ordering */
+ CLCD_CAP_RGB = CLCD_CAP_RGB444 | CLCD_CAP_RGB5551 |
+ CLCD_CAP_RGB565 | CLCD_CAP_RGB888,
+ CLCD_CAP_BGR = CLCD_CAP_BGR444 | CLCD_CAP_BGR5551 |
+ CLCD_CAP_BGR565 | CLCD_CAP_BGR888,
+
+ CLCD_CAP_ALL = CLCD_CAP_BGR | CLCD_CAP_RGB,
+};
+
+struct backlight_device;
+
+struct clcd_panel {
+ struct fb_videomode mode;
+ signed short width; /* width in mm */
+ signed short height; /* height in mm */
+ u32 tim2;
+ u32 tim3;
+ u32 cntl;
+ u32 caps;
+ unsigned int bpp:8,
+ fixedtimings:1,
+ grayscale:1;
+ unsigned int connector;
+ struct backlight_device *backlight;
+ /*
+ * If the B/R lines are switched between the CLCD
+ * and the panel we need to know this and not try to
+ * compensate with the BGR bit in the control register.
+ */
+ bool bgr_connection;
+};
+
+struct clcd_regs {
+ u32 tim0;
+ u32 tim1;
+ u32 tim2;
+ u32 tim3;
+ u32 cntl;
+ unsigned long pixclock;
+};
+
+struct clcd_fb;
+
+/*
+ * the board-type specific routines
+ */
+struct clcd_board {
+ const char *name;
+
+ /*
+ * Optional. Hardware capability flags.
+ */
+ u32 caps;
+
+ /*
+ * Optional. Check whether the var structure is acceptable
+ * for this display.
+ */
+ int (*check)(struct clcd_fb *fb, struct fb_var_screeninfo *var);
+
+ /*
+ * Compulsory. Decode fb->fb.var into regs->*. In the case of
+ * fixed timing, set regs->* to the register values required.
+ */
+ void (*decode)(struct clcd_fb *fb, struct clcd_regs *regs);
+
+ /*
+ * Optional. Disable any extra display hardware.
+ */
+ void (*disable)(struct clcd_fb *);
+
+ /*
+ * Optional. Enable any extra display hardware.
+ */
+ void (*enable)(struct clcd_fb *);
+
+ /*
+ * Setup platform specific parts of CLCD driver
+ */
+ int (*setup)(struct clcd_fb *);
+
+ /*
+ * mmap the framebuffer memory
+ */
+ int (*mmap)(struct clcd_fb *, struct vm_area_struct *);
+
+ /*
+ * Remove platform specific parts of CLCD driver
+ */
+ void (*remove)(struct clcd_fb *);
+};
+
+struct amba_device;
+struct clk;
+
+/**
+ * struct clcd_vendor_data - holds hardware (IP-block) vendor-specific
+ * variant information
+ *
+ * @clock_timregs: the CLCD needs to be clocked when accessing the
+ * timer registers, or the hardware will hang.
+ * @packed_24_bit_pixels: this variant supports 24bit packed pixel data,
+ * so that RGB accesses 3 bytes at a time, not just on even 32bit
+ * boundaries, packing the pixel data in memory. ST Microelectronics
+ * have this.
+ * @st_bitmux_control: ST Microelectronics have implemented output
+ * bit line multiplexing into the CLCD control register. This indicates
+ * that we need to use this.
+ * @init_board: custom board init function for this variant
+ * @init_panel: custom panel init function for this variant
+ */
+struct clcd_vendor_data {
+ bool clock_timregs;
+ bool packed_24_bit_pixels;
+ bool st_bitmux_control;
+ int (*init_board)(struct amba_device *adev,
+ struct clcd_board *board);
+ int (*init_panel)(struct clcd_fb *fb,
+ struct device_node *panel);
+};
+
+/* this data structure describes each frame buffer device we find */
+struct clcd_fb {
+ struct fb_info fb;
+ struct amba_device *dev;
+ struct clk *clk;
+ struct clcd_vendor_data *vendor;
+ struct clcd_panel *panel;
+ struct clcd_board *board;
+ void *board_data;
+ void __iomem *regs;
+ u16 off_ienb;
+ u16 off_cntl;
+ u32 clcd_cntl;
+ u32 cmap[16];
+ bool clk_enabled;
+};
+
+static inline void clcdfb_decode(struct clcd_fb *fb, struct clcd_regs *regs)
+{
+ struct fb_var_screeninfo *var = &fb->fb.var;
+ u32 val, cpl;
+
+ /*
+ * Program the CLCD controller registers and start the CLCD
+ */
+ val = ((var->xres / 16) - 1) << 2;
+ val |= (var->hsync_len - 1) << 8;
+ val |= (var->right_margin - 1) << 16;
+ val |= (var->left_margin - 1) << 24;
+ regs->tim0 = val;
+
+ val = var->yres;
+ if (fb->panel->cntl & CNTL_LCDDUAL)
+ val /= 2;
+ val -= 1;
+ val |= (var->vsync_len - 1) << 10;
+ val |= var->lower_margin << 16;
+ val |= var->upper_margin << 24;
+ regs->tim1 = val;
+
+ val = fb->panel->tim2;
+ val |= var->sync & FB_SYNC_HOR_HIGH_ACT ? 0 : TIM2_IHS;
+ val |= var->sync & FB_SYNC_VERT_HIGH_ACT ? 0 : TIM2_IVS;
+
+ cpl = var->xres_virtual;
+ if (fb->panel->cntl & CNTL_LCDTFT) /* TFT */
+ /* / 1 */;
+ else if (!var->grayscale) /* STN color */
+ cpl = cpl * 8 / 3;
+ else if (fb->panel->cntl & CNTL_LCDMONO8) /* STN monochrome, 8bit */
+ cpl /= 8;
+ else /* STN monochrome, 4bit */
+ cpl /= 4;
+
+ regs->tim2 = val | ((cpl - 1) << 16);
+
+ regs->tim3 = fb->panel->tim3;
+
+ val = fb->panel->cntl;
+ if (var->grayscale)
+ val |= CNTL_LCDBW;
+
+ if (fb->panel->caps && fb->board->caps && var->bits_per_pixel >= 16) {
+ /*
+ * if board and panel supply capabilities, we can support
+ * changing BGR/RGB depending on supplied parameters. Here
+ * we switch to what the framebuffer is providing if need
+ * be, so if the framebuffer is BGR but the display connection
+ * is RGB (first case) we switch it around. Vice versa mutatis
+ * mutandis if the framebuffer is RGB but the display connection
+ * is BGR, we flip it around.
+ */
+ if (var->red.offset == 0)
+ val &= ~CNTL_BGR;
+ else
+ val |= CNTL_BGR;
+ if (fb->panel->bgr_connection)
+ val ^= CNTL_BGR;
+ }
+
+ switch (var->bits_per_pixel) {
+ case 1:
+ val |= CNTL_LCDBPP1;
+ break;
+ case 2:
+ val |= CNTL_LCDBPP2;
+ break;
+ case 4:
+ val |= CNTL_LCDBPP4;
+ break;
+ case 8:
+ val |= CNTL_LCDBPP8;
+ break;
+ case 16:
+ /*
+ * PL110 cannot choose between 5551 and 565 modes in its
+ * control register. It is possible to use 565 with
+ * custom external wiring.
+ */
+ if (amba_part(fb->dev) == 0x110 ||
+ var->green.length == 5)
+ val |= CNTL_LCDBPP16;
+ else if (var->green.length == 6)
+ val |= CNTL_LCDBPP16_565;
+ else
+ val |= CNTL_LCDBPP16_444;
+ break;
+ case 24:
+ /* Modified variant supporting 24 bit packed pixels */
+ val |= CNTL_ST_LCDBPP24_PACKED;
+ break;
+ case 32:
+ val |= CNTL_LCDBPP24;
+ break;
+ }
+
+ regs->cntl = val;
+ regs->pixclock = var->pixclock;
+}
+
+static inline int clcdfb_check(struct clcd_fb *fb, struct fb_var_screeninfo *var)
+{
+ var->xres_virtual = var->xres = (var->xres + 15) & ~15;
+ var->yres_virtual = var->yres = (var->yres + 1) & ~1;
+
+#define CHECK(e,l,h) (var->e < l || var->e > h)
+ if (CHECK(right_margin, (5+1), 256) || /* back porch */
+ CHECK(left_margin, (5+1), 256) || /* front porch */
+ CHECK(hsync_len, (5+1), 256) ||
+ var->xres > 4096 ||
+ var->lower_margin > 255 || /* back porch */
+ var->upper_margin > 255 || /* front porch */
+ var->vsync_len > 32 ||
+ var->yres > 1024)
+ return -EINVAL;
+#undef CHECK
+
+ /* single panel mode: PCD = max(PCD, 1) */
+ /* dual panel mode: PCD = max(PCD, 5) */
+
+ /*
+ * You can't change the grayscale setting, and
+ * we can only do non-interlaced video.
+ */
+ if (var->grayscale != fb->fb.var.grayscale ||
+ (var->vmode & FB_VMODE_MASK) != FB_VMODE_NONINTERLACED)
+ return -EINVAL;
+
+#define CHECK(e) (var->e != fb->fb.var.e)
+ if (fb->panel->fixedtimings &&
+ (CHECK(xres) ||
+ CHECK(yres) ||
+ CHECK(bits_per_pixel) ||
+ CHECK(pixclock) ||
+ CHECK(left_margin) ||
+ CHECK(right_margin) ||
+ CHECK(upper_margin) ||
+ CHECK(lower_margin) ||
+ CHECK(hsync_len) ||
+ CHECK(vsync_len) ||
+ CHECK(sync)))
+ return -EINVAL;
+#undef CHECK
+
+ var->nonstd = 0;
+ var->accel_flags = 0;
+
+ return 0;
+}
diff --git a/include/linux/amba/kmi.h b/include/linux/amba/kmi.h
new file mode 100644
index 0000000..a39e5be
--- /dev/null
+++ b/include/linux/amba/kmi.h
@@ -0,0 +1,92 @@
+/*
+ * linux/include/asm-arm/hardware/amba_kmi.h
+ *
+ * Internal header file for AMBA KMI ports
+ *
+ * Copyright (C) 2000 Deep Blue Solutions Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ *
+ * ---------------------------------------------------------------------------
+ * From ARM PrimeCell(tm) PS2 Keyboard/Mouse Interface (PL050) Technical
+ * Reference Manual - ARM DDI 0143B - see http://www.arm.com/
+ * ---------------------------------------------------------------------------
+ */
+#ifndef ASM_ARM_HARDWARE_AMBA_KMI_H
+#define ASM_ARM_HARDWARE_AMBA_KMI_H
+
+/*
+ * KMI control register:
+ * KMICR_TYPE 0 = PS2/AT mode, 1 = No line control bit mode
+ * KMICR_RXINTREN 1 = enable RX interrupts
+ * KMICR_TXINTREN 1 = enable TX interrupts
+ * KMICR_EN 1 = enable KMI
+ * KMICR_FD 1 = force KMI data low
+ * KMICR_FC 1 = force KMI clock low
+ */
+#define KMICR (KMI_BASE + 0x00)
+#define KMICR_TYPE (1 << 5)
+#define KMICR_RXINTREN (1 << 4)
+#define KMICR_TXINTREN (1 << 3)
+#define KMICR_EN (1 << 2)
+#define KMICR_FD (1 << 1)
+#define KMICR_FC (1 << 0)
+
+/*
+ * KMI status register:
+ * KMISTAT_TXEMPTY 1 = transmitter register empty
+ * KMISTAT_TXBUSY 1 = currently sending data
+ * KMISTAT_RXFULL 1 = receiver register ready to be read
+ * KMISTAT_RXBUSY 1 = currently receiving data
+ * KMISTAT_RXPARITY parity of last databyte received
+ * KMISTAT_IC current level of KMI clock input
+ * KMISTAT_ID current level of KMI data input
+ */
+#define KMISTAT (KMI_BASE + 0x04)
+#define KMISTAT_TXEMPTY (1 << 6)
+#define KMISTAT_TXBUSY (1 << 5)
+#define KMISTAT_RXFULL (1 << 4)
+#define KMISTAT_RXBUSY (1 << 3)
+#define KMISTAT_RXPARITY (1 << 2)
+#define KMISTAT_IC (1 << 1)
+#define KMISTAT_ID (1 << 0)
+
+/*
+ * KMI data register
+ */
+#define KMIDATA (KMI_BASE + 0x08)
+
+/*
+ * KMI clock divisor: to generate 8MHz internal clock
+ * div = (ref / 8MHz) - 1; 0 <= div <= 15
+ */
+#define KMICLKDIV (KMI_BASE + 0x0c)
+
+/*
+ * KMI interrupt register:
+ * KMIIR_TXINTR 1 = transmit interrupt asserted
+ * KMIIR_RXINTR 1 = receive interrupt asserted
+ */
+#define KMIIR (KMI_BASE + 0x10)
+#define KMIIR_TXINTR (1 << 1)
+#define KMIIR_RXINTR (1 << 0)
+
+/*
+ * The size of the KMI primecell
+ */
+#define KMI_SIZE (0x100)
+
+#endif
diff --git a/include/linux/amba/mmci.h b/include/linux/amba/mmci.h
new file mode 100644
index 0000000..da8357b
--- /dev/null
+++ b/include/linux/amba/mmci.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * include/linux/amba/mmci.h
+ */
+#ifndef AMBA_MMCI_H
+#define AMBA_MMCI_H
+
+#include <linux/mmc/host.h>
+
+/**
+ * struct mmci_platform_data - platform configuration for the MMCI
+ * (also known as PL180) block.
+ * @ocr_mask: available voltages on the 4 pins from the block, this
+ * is ignored if a regulator is used, see the MMC_VDD_* masks in
+ * mmc/host.h
+ * @ios_handler: a callback function to act on specfic ios changes,
+ * used for example to control a levelshifter
+ * mask into a value to be binary (or set some other custom bits
+ * in MMCIPWR) or:ed and written into the MMCIPWR register of the
+ * block. May also control external power based on the power_mode.
+ * @status: if no GPIO read function was given to the block in
+ * gpio_wp (below) this function will be called to determine
+ * whether a card is present in the MMC slot or not
+ * @gpio_wp: read this GPIO pin to see if the card is write protected
+ * @gpio_cd: read this GPIO pin to detect card insertion
+ * @cd_invert: true if the gpio_cd pin value is active low
+ */
+struct mmci_platform_data {
+ unsigned int ocr_mask;
+ int (*ios_handler)(struct device *, struct mmc_ios *);
+ unsigned int (*status)(struct device *);
+ int gpio_wp;
+ int gpio_cd;
+ bool cd_invert;
+};
+
+#endif
diff --git a/include/linux/amba/pl022.h b/include/linux/amba/pl022.h
new file mode 100644
index 0000000..854b729
--- /dev/null
+++ b/include/linux/amba/pl022.h
@@ -0,0 +1,295 @@
+/*
+ * include/linux/amba/pl022.h
+ *
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * Copyright (C) 2006 STMicroelectronics Pvt. Ltd.
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ *
+ * Initial version inspired by:
+ * linux-2.6.17-rc3-mm1/drivers/spi/pxa2xx_spi.c
+ * Initial adoption to PL022 by:
+ * Sachin Verma <sachin.verma@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _SSP_PL022_H
+#define _SSP_PL022_H
+
+#include <linux/types.h>
+
+/**
+ * whether SSP is in loopback mode or not
+ */
+enum ssp_loopback {
+ LOOPBACK_DISABLED,
+ LOOPBACK_ENABLED
+};
+
+/**
+ * enum ssp_interface - interfaces allowed for this SSP Controller
+ * @SSP_INTERFACE_MOTOROLA_SPI: Motorola Interface
+ * @SSP_INTERFACE_TI_SYNC_SERIAL: Texas Instrument Synchronous Serial
+ * interface
+ * @SSP_INTERFACE_NATIONAL_MICROWIRE: National Semiconductor Microwire
+ * interface
+ * @SSP_INTERFACE_UNIDIRECTIONAL: Unidirectional interface (STn8810
+ * &STn8815 only)
+ */
+enum ssp_interface {
+ SSP_INTERFACE_MOTOROLA_SPI,
+ SSP_INTERFACE_TI_SYNC_SERIAL,
+ SSP_INTERFACE_NATIONAL_MICROWIRE,
+ SSP_INTERFACE_UNIDIRECTIONAL
+};
+
+/**
+ * enum ssp_hierarchy - whether SSP is configured as Master or Slave
+ */
+enum ssp_hierarchy {
+ SSP_MASTER,
+ SSP_SLAVE
+};
+
+/**
+ * enum ssp_clock_params - clock parameters, to set SSP clock at a
+ * desired freq
+ */
+struct ssp_clock_params {
+ u8 cpsdvsr; /* value from 2 to 254 (even only!) */
+ u8 scr; /* value from 0 to 255 */
+};
+
+/**
+ * enum ssp_rx_endian - endianess of Rx FIFO Data
+ * this feature is only available in ST versionf of PL022
+ */
+enum ssp_rx_endian {
+ SSP_RX_MSB,
+ SSP_RX_LSB
+};
+
+/**
+ * enum ssp_tx_endian - endianess of Tx FIFO Data
+ */
+enum ssp_tx_endian {
+ SSP_TX_MSB,
+ SSP_TX_LSB
+};
+
+/**
+ * enum ssp_data_size - number of bits in one data element
+ */
+enum ssp_data_size {
+ SSP_DATA_BITS_4 = 0x03, SSP_DATA_BITS_5, SSP_DATA_BITS_6,
+ SSP_DATA_BITS_7, SSP_DATA_BITS_8, SSP_DATA_BITS_9,
+ SSP_DATA_BITS_10, SSP_DATA_BITS_11, SSP_DATA_BITS_12,
+ SSP_DATA_BITS_13, SSP_DATA_BITS_14, SSP_DATA_BITS_15,
+ SSP_DATA_BITS_16, SSP_DATA_BITS_17, SSP_DATA_BITS_18,
+ SSP_DATA_BITS_19, SSP_DATA_BITS_20, SSP_DATA_BITS_21,
+ SSP_DATA_BITS_22, SSP_DATA_BITS_23, SSP_DATA_BITS_24,
+ SSP_DATA_BITS_25, SSP_DATA_BITS_26, SSP_DATA_BITS_27,
+ SSP_DATA_BITS_28, SSP_DATA_BITS_29, SSP_DATA_BITS_30,
+ SSP_DATA_BITS_31, SSP_DATA_BITS_32
+};
+
+/**
+ * enum ssp_mode - SSP mode of operation (Communication modes)
+ */
+enum ssp_mode {
+ INTERRUPT_TRANSFER,
+ POLLING_TRANSFER,
+ DMA_TRANSFER
+};
+
+/**
+ * enum ssp_rx_level_trig - receive FIFO watermark level which triggers
+ * IT: Interrupt fires when _N_ or more elements in RX FIFO.
+ */
+enum ssp_rx_level_trig {
+ SSP_RX_1_OR_MORE_ELEM,
+ SSP_RX_4_OR_MORE_ELEM,
+ SSP_RX_8_OR_MORE_ELEM,
+ SSP_RX_16_OR_MORE_ELEM,
+ SSP_RX_32_OR_MORE_ELEM
+};
+
+/**
+ * Transmit FIFO watermark level which triggers (IT Interrupt fires
+ * when _N_ or more empty locations in TX FIFO)
+ */
+enum ssp_tx_level_trig {
+ SSP_TX_1_OR_MORE_EMPTY_LOC,
+ SSP_TX_4_OR_MORE_EMPTY_LOC,
+ SSP_TX_8_OR_MORE_EMPTY_LOC,
+ SSP_TX_16_OR_MORE_EMPTY_LOC,
+ SSP_TX_32_OR_MORE_EMPTY_LOC
+};
+
+/**
+ * enum SPI Clock Phase - clock phase (Motorola SPI interface only)
+ * @SSP_CLK_FIRST_EDGE: Receive data on first edge transition (actual direction depends on polarity)
+ * @SSP_CLK_SECOND_EDGE: Receive data on second edge transition (actual direction depends on polarity)
+ */
+enum ssp_spi_clk_phase {
+ SSP_CLK_FIRST_EDGE,
+ SSP_CLK_SECOND_EDGE
+};
+
+/**
+ * enum SPI Clock Polarity - clock polarity (Motorola SPI interface only)
+ * @SSP_CLK_POL_IDLE_LOW: Low inactive level
+ * @SSP_CLK_POL_IDLE_HIGH: High inactive level
+ */
+enum ssp_spi_clk_pol {
+ SSP_CLK_POL_IDLE_LOW,
+ SSP_CLK_POL_IDLE_HIGH
+};
+
+/**
+ * Microwire Conrol Lengths Command size in microwire format
+ */
+enum ssp_microwire_ctrl_len {
+ SSP_BITS_4 = 0x03, SSP_BITS_5, SSP_BITS_6,
+ SSP_BITS_7, SSP_BITS_8, SSP_BITS_9,
+ SSP_BITS_10, SSP_BITS_11, SSP_BITS_12,
+ SSP_BITS_13, SSP_BITS_14, SSP_BITS_15,
+ SSP_BITS_16, SSP_BITS_17, SSP_BITS_18,
+ SSP_BITS_19, SSP_BITS_20, SSP_BITS_21,
+ SSP_BITS_22, SSP_BITS_23, SSP_BITS_24,
+ SSP_BITS_25, SSP_BITS_26, SSP_BITS_27,
+ SSP_BITS_28, SSP_BITS_29, SSP_BITS_30,
+ SSP_BITS_31, SSP_BITS_32
+};
+
+/**
+ * enum Microwire Wait State
+ * @SSP_MWIRE_WAIT_ZERO: No wait state inserted after last command bit
+ * @SSP_MWIRE_WAIT_ONE: One wait state inserted after last command bit
+ */
+enum ssp_microwire_wait_state {
+ SSP_MWIRE_WAIT_ZERO,
+ SSP_MWIRE_WAIT_ONE
+};
+
+/**
+ * enum ssp_duplex - whether Full/Half Duplex on microwire, only
+ * available in the ST Micro variant.
+ * @SSP_MICROWIRE_CHANNEL_FULL_DUPLEX: SSPTXD becomes bi-directional,
+ * SSPRXD not used
+ * @SSP_MICROWIRE_CHANNEL_HALF_DUPLEX: SSPTXD is an output, SSPRXD is
+ * an input.
+ */
+enum ssp_duplex {
+ SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
+ SSP_MICROWIRE_CHANNEL_HALF_DUPLEX
+};
+
+/**
+ * enum ssp_clkdelay - an optional clock delay on the feedback clock
+ * only available in the ST Micro PL023 variant.
+ * @SSP_FEEDBACK_CLK_DELAY_NONE: no delay, the data coming in from the
+ * slave is sampled directly
+ * @SSP_FEEDBACK_CLK_DELAY_1T: the incoming slave data is sampled with
+ * a delay of T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_2T: dito with a delay if 2T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_3T: dito with a delay if 3T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_4T: dito with a delay if 4T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_5T: dito with a delay if 5T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_6T: dito with a delay if 6T-dt
+ * @SSP_FEEDBACK_CLK_DELAY_7T: dito with a delay if 7T-dt
+ */
+enum ssp_clkdelay {
+ SSP_FEEDBACK_CLK_DELAY_NONE,
+ SSP_FEEDBACK_CLK_DELAY_1T,
+ SSP_FEEDBACK_CLK_DELAY_2T,
+ SSP_FEEDBACK_CLK_DELAY_3T,
+ SSP_FEEDBACK_CLK_DELAY_4T,
+ SSP_FEEDBACK_CLK_DELAY_5T,
+ SSP_FEEDBACK_CLK_DELAY_6T,
+ SSP_FEEDBACK_CLK_DELAY_7T
+};
+
+/**
+ * CHIP select/deselect commands
+ */
+enum ssp_chip_select {
+ SSP_CHIP_SELECT,
+ SSP_CHIP_DESELECT
+};
+
+
+struct dma_chan;
+/**
+ * struct pl022_ssp_master - device.platform_data for SPI controller devices.
+ * @bus_id: identifier for this bus
+ * @num_chipselect: chipselects are used to distinguish individual
+ * SPI slaves, and are numbered from zero to num_chipselects - 1.
+ * each slave has a chipselect signal, but it's common that not
+ * every chipselect is connected to a slave.
+ * @enable_dma: if true enables DMA driven transfers.
+ * @dma_rx_param: parameter to locate an RX DMA channel.
+ * @dma_tx_param: parameter to locate a TX DMA channel.
+ * @autosuspend_delay: delay in ms following transfer completion before the
+ * runtime power management system suspends the device. A setting of 0
+ * indicates no delay and the device will be suspended immediately.
+ * @rt: indicates the controller should run the message pump with realtime
+ * priority to minimise the transfer latency on the bus.
+ * @chipselects: list of <num_chipselects> chip select gpios
+ */
+struct pl022_ssp_controller {
+ u16 bus_id;
+ u8 num_chipselect;
+ u8 enable_dma:1;
+ bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
+ void *dma_rx_param;
+ void *dma_tx_param;
+ int autosuspend_delay;
+ bool rt;
+ int *chipselects;
+};
+
+/**
+ * struct ssp_config_chip - spi_board_info.controller_data for SPI
+ * slave devices, copied to spi_device.controller_data.
+ *
+ * @iface: Interface type(Motorola, TI, Microwire, Universal)
+ * @hierarchy: sets whether interface is master or slave
+ * @slave_tx_disable: SSPTXD is disconnected (in slave mode only)
+ * @clk_freq: Tune freq parameters of SSP(when in master mode)
+ * @com_mode: communication mode: polling, Interrupt or DMA
+ * @rx_lev_trig: Rx FIFO watermark level (for IT & DMA mode)
+ * @tx_lev_trig: Tx FIFO watermark level (for IT & DMA mode)
+ * @ctrl_len: Microwire interface: Control length
+ * @wait_state: Microwire interface: Wait state
+ * @duplex: Microwire interface: Full/Half duplex
+ * @clkdelay: on the PL023 variant, the delay in feeback clock cycles
+ * before sampling the incoming line
+ * @cs_control: function pointer to board-specific function to
+ * assert/deassert I/O port to control HW generation of devices chip-select.
+ */
+struct pl022_config_chip {
+ enum ssp_interface iface;
+ enum ssp_hierarchy hierarchy;
+ bool slave_tx_disable;
+ struct ssp_clock_params clk_freq;
+ enum ssp_mode com_mode;
+ enum ssp_rx_level_trig rx_lev_trig;
+ enum ssp_tx_level_trig tx_lev_trig;
+ enum ssp_microwire_ctrl_len ctrl_len;
+ enum ssp_microwire_wait_state wait_state;
+ enum ssp_duplex duplex;
+ enum ssp_clkdelay clkdelay;
+ void (*cs_control) (u32 control);
+};
+
+#endif /* _SSP_PL022_H */
diff --git a/include/linux/amba/pl080.h b/include/linux/amba/pl080.h
new file mode 100644
index 0000000..ab036b6
--- /dev/null
+++ b/include/linux/amba/pl080.h
@@ -0,0 +1,220 @@
+/* include/linux/amba/pl080.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * ARM PrimeCell PL080 DMA controller
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* Note, there are some Samsung updates to this controller block which
+ * make it not entierly compatible with the PL080 specification from
+ * ARM. When in doubt, check the Samsung documentation first.
+ *
+ * The Samsung defines are PL080S, and add an extra control register,
+ * the ability to move more than 2^11 counts of data and some extra
+ * OneNAND features.
+*/
+
+#ifndef ASM_PL080_H
+#define ASM_PL080_H
+
+#define PL080_INT_STATUS (0x00)
+#define PL080_TC_STATUS (0x04)
+#define PL080_TC_CLEAR (0x08)
+#define PL080_ERR_STATUS (0x0C)
+#define PL080_ERR_CLEAR (0x10)
+#define PL080_RAW_TC_STATUS (0x14)
+#define PL080_RAW_ERR_STATUS (0x18)
+#define PL080_EN_CHAN (0x1c)
+#define PL080_SOFT_BREQ (0x20)
+#define PL080_SOFT_SREQ (0x24)
+#define PL080_SOFT_LBREQ (0x28)
+#define PL080_SOFT_LSREQ (0x2C)
+
+#define PL080_CONFIG (0x30)
+#define PL080_CONFIG_M2_BE BIT(2)
+#define PL080_CONFIG_M1_BE BIT(1)
+#define PL080_CONFIG_ENABLE BIT(0)
+
+#define PL080_SYNC (0x34)
+
+/* The Faraday Technology FTDMAC020 variant registers */
+#define FTDMAC020_CH_BUSY (0x20)
+/* Identical to PL080_CONFIG */
+#define FTDMAC020_CSR (0x24)
+/* Identical to PL080_SYNC */
+#define FTDMAC020_SYNC (0x2C)
+#define FTDMAC020_REVISION (0x30)
+#define FTDMAC020_FEATURE (0x34)
+
+/* Per channel configuration registers */
+#define PL080_Cx_BASE(x) ((0x100 + (x * 0x20)))
+#define PL080_CH_SRC_ADDR (0x00)
+#define PL080_CH_DST_ADDR (0x04)
+#define PL080_CH_LLI (0x08)
+#define PL080_CH_CONTROL (0x0C)
+#define PL080_CH_CONFIG (0x10)
+#define PL080S_CH_CONTROL2 (0x10)
+#define PL080S_CH_CONFIG (0x14)
+/* The Faraday FTDMAC020 derivative shuffles the registers around */
+#define FTDMAC020_CH_CSR (0x00)
+#define FTDMAC020_CH_CFG (0x04)
+#define FTDMAC020_CH_SRC_ADDR (0x08)
+#define FTDMAC020_CH_DST_ADDR (0x0C)
+#define FTDMAC020_CH_LLP (0x10)
+#define FTDMAC020_CH_SIZE (0x14)
+
+#define PL080_LLI_ADDR_MASK GENMASK(31, 2)
+#define PL080_LLI_ADDR_SHIFT (2)
+#define PL080_LLI_LM_AHB2 BIT(0)
+
+#define PL080_CONTROL_TC_IRQ_EN BIT(31)
+#define PL080_CONTROL_PROT_MASK GENMASK(30, 28)
+#define PL080_CONTROL_PROT_SHIFT (28)
+#define PL080_CONTROL_PROT_CACHE BIT(30)
+#define PL080_CONTROL_PROT_BUFF BIT(29)
+#define PL080_CONTROL_PROT_SYS BIT(28)
+#define PL080_CONTROL_DST_INCR BIT(27)
+#define PL080_CONTROL_SRC_INCR BIT(26)
+#define PL080_CONTROL_DST_AHB2 BIT(25)
+#define PL080_CONTROL_SRC_AHB2 BIT(24)
+#define PL080_CONTROL_DWIDTH_MASK GENMASK(23, 21)
+#define PL080_CONTROL_DWIDTH_SHIFT (21)
+#define PL080_CONTROL_SWIDTH_MASK GENMASK(20, 18)
+#define PL080_CONTROL_SWIDTH_SHIFT (18)
+#define PL080_CONTROL_DB_SIZE_MASK GENMASK(17, 15)
+#define PL080_CONTROL_DB_SIZE_SHIFT (15)
+#define PL080_CONTROL_SB_SIZE_MASK GENMASK(14, 12)
+#define PL080_CONTROL_SB_SIZE_SHIFT (12)
+#define PL080_CONTROL_TRANSFER_SIZE_MASK GENMASK(11, 0)
+#define PL080S_CONTROL_TRANSFER_SIZE_MASK GENMASK(24, 0)
+#define PL080_CONTROL_TRANSFER_SIZE_SHIFT (0)
+
+#define PL080_BSIZE_1 (0x0)
+#define PL080_BSIZE_4 (0x1)
+#define PL080_BSIZE_8 (0x2)
+#define PL080_BSIZE_16 (0x3)
+#define PL080_BSIZE_32 (0x4)
+#define PL080_BSIZE_64 (0x5)
+#define PL080_BSIZE_128 (0x6)
+#define PL080_BSIZE_256 (0x7)
+
+#define PL080_WIDTH_8BIT (0x0)
+#define PL080_WIDTH_16BIT (0x1)
+#define PL080_WIDTH_32BIT (0x2)
+
+#define PL080N_CONFIG_ITPROT BIT(20)
+#define PL080N_CONFIG_SECPROT BIT(19)
+#define PL080_CONFIG_HALT BIT(18)
+#define PL080_CONFIG_ACTIVE BIT(17) /* RO */
+#define PL080_CONFIG_LOCK BIT(16)
+#define PL080_CONFIG_TC_IRQ_MASK BIT(15)
+#define PL080_CONFIG_ERR_IRQ_MASK BIT(14)
+#define PL080_CONFIG_FLOW_CONTROL_MASK GENMASK(13, 11)
+#define PL080_CONFIG_FLOW_CONTROL_SHIFT (11)
+#define PL080_CONFIG_DST_SEL_MASK GENMASK(9, 6)
+#define PL080_CONFIG_DST_SEL_SHIFT (6)
+#define PL080_CONFIG_SRC_SEL_MASK GENMASK(4, 1)
+#define PL080_CONFIG_SRC_SEL_SHIFT (1)
+#define PL080_CONFIG_ENABLE BIT(0)
+
+#define PL080_FLOW_MEM2MEM (0x0)
+#define PL080_FLOW_MEM2PER (0x1)
+#define PL080_FLOW_PER2MEM (0x2)
+#define PL080_FLOW_SRC2DST (0x3)
+#define PL080_FLOW_SRC2DST_DST (0x4)
+#define PL080_FLOW_MEM2PER_PER (0x5)
+#define PL080_FLOW_PER2MEM_PER (0x6)
+#define PL080_FLOW_SRC2DST_SRC (0x7)
+
+#define FTDMAC020_CH_CSR_TC_MSK BIT(31)
+/* Later versions have a threshold in bits 24..26, */
+#define FTDMAC020_CH_CSR_FIFOTH_MSK GENMASK(26, 24)
+#define FTDMAC020_CH_CSR_FIFOTH_SHIFT (24)
+#define FTDMAC020_CH_CSR_CHPR1_MSK GENMASK(23, 22)
+#define FTDMAC020_CH_CSR_PROT3 BIT(21)
+#define FTDMAC020_CH_CSR_PROT2 BIT(20)
+#define FTDMAC020_CH_CSR_PROT1 BIT(19)
+#define FTDMAC020_CH_CSR_SRC_SIZE_MSK GENMASK(18, 16)
+#define FTDMAC020_CH_CSR_SRC_SIZE_SHIFT (16)
+#define FTDMAC020_CH_CSR_ABT BIT(15)
+#define FTDMAC020_CH_CSR_SRC_WIDTH_MSK GENMASK(13, 11)
+#define FTDMAC020_CH_CSR_SRC_WIDTH_SHIFT (11)
+#define FTDMAC020_CH_CSR_DST_WIDTH_MSK GENMASK(10, 8)
+#define FTDMAC020_CH_CSR_DST_WIDTH_SHIFT (8)
+#define FTDMAC020_CH_CSR_MODE BIT(7)
+/* 00 = increase, 01 = decrease, 10 = fix */
+#define FTDMAC020_CH_CSR_SRCAD_CTL_MSK GENMASK(6, 5)
+#define FTDMAC020_CH_CSR_SRCAD_CTL_SHIFT (5)
+#define FTDMAC020_CH_CSR_DSTAD_CTL_MSK GENMASK(4, 3)
+#define FTDMAC020_CH_CSR_DSTAD_CTL_SHIFT (3)
+#define FTDMAC020_CH_CSR_SRC_SEL BIT(2)
+#define FTDMAC020_CH_CSR_DST_SEL BIT(1)
+#define FTDMAC020_CH_CSR_EN BIT(0)
+
+/* FIFO threshold setting */
+#define FTDMAC020_CH_CSR_FIFOTH_1 (0x0)
+#define FTDMAC020_CH_CSR_FIFOTH_2 (0x1)
+#define FTDMAC020_CH_CSR_FIFOTH_4 (0x2)
+#define FTDMAC020_CH_CSR_FIFOTH_8 (0x3)
+#define FTDMAC020_CH_CSR_FIFOTH_16 (0x4)
+/* The FTDMAC020 supports 64bit wide transfers */
+#define FTDMAC020_WIDTH_64BIT (0x3)
+/* Address can be increased, decreased or fixed */
+#define FTDMAC020_CH_CSR_SRCAD_CTL_INC (0x0)
+#define FTDMAC020_CH_CSR_SRCAD_CTL_DEC (0x1)
+#define FTDMAC020_CH_CSR_SRCAD_CTL_FIXED (0x2)
+
+#define FTDMAC020_CH_CFG_LLP_CNT_MASK GENMASK(19, 16)
+#define FTDMAC020_CH_CFG_LLP_CNT_SHIFT (16)
+#define FTDMAC020_CH_CFG_BUSY BIT(8)
+#define FTDMAC020_CH_CFG_INT_ABT_MASK BIT(2)
+#define FTDMAC020_CH_CFG_INT_ERR_MASK BIT(1)
+#define FTDMAC020_CH_CFG_INT_TC_MASK BIT(0)
+
+/* Inside the LLIs, the applicable CSR fields are mapped differently */
+#define FTDMAC020_LLI_TC_MSK BIT(28)
+#define FTDMAC020_LLI_SRC_WIDTH_MSK GENMASK(27, 25)
+#define FTDMAC020_LLI_SRC_WIDTH_SHIFT (25)
+#define FTDMAC020_LLI_DST_WIDTH_MSK GENMASK(24, 22)
+#define FTDMAC020_LLI_DST_WIDTH_SHIFT (22)
+#define FTDMAC020_LLI_SRCAD_CTL_MSK GENMASK(21, 20)
+#define FTDMAC020_LLI_SRCAD_CTL_SHIFT (20)
+#define FTDMAC020_LLI_DSTAD_CTL_MSK GENMASK(19, 18)
+#define FTDMAC020_LLI_DSTAD_CTL_SHIFT (18)
+#define FTDMAC020_LLI_SRC_SEL BIT(17)
+#define FTDMAC020_LLI_DST_SEL BIT(16)
+#define FTDMAC020_LLI_TRANSFER_SIZE_MASK GENMASK(11, 0)
+#define FTDMAC020_LLI_TRANSFER_SIZE_SHIFT (0)
+
+#define FTDMAC020_CFG_LLP_CNT_MASK GENMASK(19, 16)
+#define FTDMAC020_CFG_LLP_CNT_SHIFT (16)
+#define FTDMAC020_CFG_BUSY BIT(8)
+#define FTDMAC020_CFG_INT_ABT_MSK BIT(2)
+#define FTDMAC020_CFG_INT_ERR_MSK BIT(1)
+#define FTDMAC020_CFG_INT_TC_MSK BIT(0)
+
+/* DMA linked list chain structure */
+
+struct pl080_lli {
+ u32 src_addr;
+ u32 dst_addr;
+ u32 next_lli;
+ u32 control0;
+};
+
+struct pl080s_lli {
+ u32 src_addr;
+ u32 dst_addr;
+ u32 next_lli;
+ u32 control0;
+ u32 control1;
+};
+
+#endif /* ASM_PL080_H */
diff --git a/include/linux/amba/pl08x.h b/include/linux/amba/pl08x.h
new file mode 100644
index 0000000..79d1bce
--- /dev/null
+++ b/include/linux/amba/pl08x.h
@@ -0,0 +1,133 @@
+/*
+ * linux/amba/pl08x.h - ARM PrimeCell DMA Controller driver
+ *
+ * Copyright (C) 2005 ARM Ltd
+ * Copyright (C) 2010 ST-Ericsson SA
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * pl08x information required by platform code
+ *
+ * Please credit ARM.com
+ * Documentation: ARM DDI 0196D
+ */
+
+#ifndef AMBA_PL08X_H
+#define AMBA_PL08X_H
+
+/* We need sizes of structs from this header */
+#include <linux/dmaengine.h>
+#include <linux/interrupt.h>
+
+struct pl08x_driver_data;
+struct pl08x_phy_chan;
+struct pl08x_txd;
+
+/* Bitmasks for selecting AHB ports for DMA transfers */
+enum {
+ PL08X_AHB1 = (1 << 0),
+ PL08X_AHB2 = (1 << 1)
+};
+
+/**
+ * struct pl08x_channel_data - data structure to pass info between
+ * platform and PL08x driver regarding channel configuration
+ * @bus_id: name of this device channel, not just a device name since
+ * devices may have more than one channel e.g. "foo_tx"
+ * @min_signal: the minimum DMA signal number to be muxed in for this
+ * channel (for platforms supporting muxed signals). If you have
+ * static assignments, make sure this is set to the assigned signal
+ * number, PL08x have 16 possible signals in number 0 thru 15 so
+ * when these are not enough they often get muxed (in hardware)
+ * disabling simultaneous use of the same channel for two devices.
+ * @max_signal: the maximum DMA signal number to be muxed in for
+ * the channel. Set to the same as min_signal for
+ * devices with static assignments
+ * @muxval: a number usually used to poke into some mux regiser to
+ * mux in the signal to this channel
+ * @addr: source/target address in physical memory for this DMA channel,
+ * can be the address of a FIFO register for burst requests for example.
+ * This can be left undefined if the PrimeCell API is used for configuring
+ * this.
+ * @single: the device connected to this channel will request single DMA
+ * transfers, not bursts. (Bursts are default.)
+ * @periph_buses: the device connected to this channel is accessible via
+ * these buses (use PL08X_AHB1 | PL08X_AHB2).
+ */
+struct pl08x_channel_data {
+ const char *bus_id;
+ int min_signal;
+ int max_signal;
+ u32 muxval;
+ dma_addr_t addr;
+ bool single;
+ u8 periph_buses;
+};
+
+enum pl08x_burst_size {
+ PL08X_BURST_SZ_1,
+ PL08X_BURST_SZ_4,
+ PL08X_BURST_SZ_8,
+ PL08X_BURST_SZ_16,
+ PL08X_BURST_SZ_32,
+ PL08X_BURST_SZ_64,
+ PL08X_BURST_SZ_128,
+ PL08X_BURST_SZ_256,
+};
+
+enum pl08x_bus_width {
+ PL08X_BUS_WIDTH_8_BITS,
+ PL08X_BUS_WIDTH_16_BITS,
+ PL08X_BUS_WIDTH_32_BITS,
+};
+
+/**
+ * struct pl08x_platform_data - the platform configuration for the PL08x
+ * PrimeCells.
+ * @slave_channels: the channels defined for the different devices on the
+ * platform, all inclusive, including multiplexed channels. The available
+ * physical channels will be multiplexed around these signals as they are
+ * requested, just enumerate all possible channels.
+ * @num_slave_channels: number of elements in the slave channel array
+ * @memcpy_burst_size: the appropriate burst size for memcpy operations
+ * @memcpy_bus_width: memory bus width
+ * @memcpy_prot_buff: whether memcpy DMA is bufferable
+ * @memcpy_prot_cache: whether memcpy DMA is cacheable
+ * @get_xfer_signal: request a physical signal to be used for a DMA transfer
+ * immediately: if there is some multiplexing or similar blocking the use
+ * of the channel the transfer can be denied by returning less than zero,
+ * else it returns the allocated signal number
+ * @put_xfer_signal: indicate to the platform that this physical signal is not
+ * running any DMA transfer and multiplexing can be recycled
+ * @lli_buses: buses which LLIs can be fetched from: PL08X_AHB1 | PL08X_AHB2
+ * @mem_buses: buses which memory can be accessed from: PL08X_AHB1 | PL08X_AHB2
+ * @slave_map: DMA slave matching table
+ * @slave_map_len: number of elements in @slave_map
+ */
+struct pl08x_platform_data {
+ struct pl08x_channel_data *slave_channels;
+ unsigned int num_slave_channels;
+ enum pl08x_burst_size memcpy_burst_size;
+ enum pl08x_bus_width memcpy_bus_width;
+ bool memcpy_prot_buff;
+ bool memcpy_prot_cache;
+ int (*get_xfer_signal)(const struct pl08x_channel_data *);
+ void (*put_xfer_signal)(const struct pl08x_channel_data *, int);
+ u8 lli_buses;
+ u8 mem_buses;
+ const struct dma_slave_map *slave_map;
+ int slave_map_len;
+};
+
+#ifdef CONFIG_AMBA_PL08X
+bool pl08x_filter_id(struct dma_chan *chan, void *chan_id);
+#else
+static inline bool pl08x_filter_id(struct dma_chan *chan, void *chan_id)
+{
+ return false;
+}
+#endif
+
+#endif /* AMBA_PL08X_H */
diff --git a/include/linux/amba/pl093.h b/include/linux/amba/pl093.h
new file mode 100644
index 0000000..2983e36
--- /dev/null
+++ b/include/linux/amba/pl093.h
@@ -0,0 +1,80 @@
+/* linux/amba/pl093.h
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ * http://armlinux.simtec.co.uk/
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * AMBA PL093 SSMC (synchronous static memory controller)
+ * See DDI0236.pdf (r0p4) for more details
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define SMB_BANK(x) ((x) * 0x20) /* each bank control set is 0x20 apart */
+
+/* Offsets for SMBxxxxRy registers */
+
+#define SMBIDCYR (0x00)
+#define SMBWSTRDR (0x04)
+#define SMBWSTWRR (0x08)
+#define SMBWSTOENR (0x0C)
+#define SMBWSTWENR (0x10)
+#define SMBCR (0x14)
+#define SMBSR (0x18)
+#define SMBWSTBRDR (0x1C)
+
+/* Masks for SMB registers */
+#define IDCY_MASK (0xf)
+#define WSTRD_MASK (0xf)
+#define WSTWR_MASK (0xf)
+#define WSTOEN_MASK (0xf)
+#define WSTWEN_MASK (0xf)
+
+/* Notes from datasheet:
+ * WSTOEN <= WSTRD
+ * WSTWEN <= WSTWR
+ *
+ * WSTOEN is not used with nWAIT
+ */
+
+/* SMBCR bit definitions */
+#define SMBCR_BIWRITEEN (1 << 21)
+#define SMBCR_ADDRVALIDWRITEEN (1 << 20)
+#define SMBCR_SYNCWRITE (1 << 17)
+#define SMBCR_BMWRITE (1 << 16)
+#define SMBCR_WRAPREAD (1 << 14)
+#define SMBCR_BIREADEN (1 << 13)
+#define SMBCR_ADDRVALIDREADEN (1 << 12)
+#define SMBCR_SYNCREAD (1 << 9)
+#define SMBCR_BMREAD (1 << 8)
+#define SMBCR_SMBLSPOL (1 << 6)
+#define SMBCR_WP (1 << 3)
+#define SMBCR_WAITEN (1 << 2)
+#define SMBCR_WAITPOL (1 << 1)
+#define SMBCR_RBLE (1 << 0)
+
+#define SMBCR_BURSTLENWRITE_MASK (3 << 18)
+#define SMBCR_BURSTLENWRITE_4 (0 << 18)
+#define SMBCR_BURSTLENWRITE_8 (1 << 18)
+#define SMBCR_BURSTLENWRITE_RESERVED (2 << 18)
+#define SMBCR_BURSTLENWRITE_CONTINUOUS (3 << 18)
+
+#define SMBCR_BURSTLENREAD_MASK (3 << 10)
+#define SMBCR_BURSTLENREAD_4 (0 << 10)
+#define SMBCR_BURSTLENREAD_8 (1 << 10)
+#define SMBCR_BURSTLENREAD_16 (2 << 10)
+#define SMBCR_BURSTLENREAD_CONTINUOUS (3 << 10)
+
+#define SMBCR_MW_MASK (3 << 4)
+#define SMBCR_MW_8BIT (0 << 4)
+#define SMBCR_MW_16BIT (1 << 4)
+#define SMBCR_MW_M32BIT (2 << 4)
+
+/* SSMC status registers */
+#define SSMCCSR (0x200)
+#define SSMCCR (0x204)
+#define SSMCITCR (0x208)
+#define SSMCITIP (0x20C)
+#define SSMCITIOP (0x210)
diff --git a/include/linux/amba/serial.h b/include/linux/amba/serial.h
new file mode 100644
index 0000000..ad0965e
--- /dev/null
+++ b/include/linux/amba/serial.h
@@ -0,0 +1,241 @@
+/*
+ * linux/include/asm-arm/hardware/serial_amba.h
+ *
+ * Internal header file for AMBA serial ports
+ *
+ * Copyright (C) ARM Limited
+ * Copyright (C) 2000 Deep Blue Solutions Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+#ifndef ASM_ARM_HARDWARE_SERIAL_AMBA_H
+#define ASM_ARM_HARDWARE_SERIAL_AMBA_H
+
+#include <linux/types.h>
+
+/* -------------------------------------------------------------------------------
+ * From AMBA UART (PL010) Block Specification
+ * -------------------------------------------------------------------------------
+ * UART Register Offsets.
+ */
+#define UART01x_DR 0x00 /* Data read or written from the interface. */
+#define UART01x_RSR 0x04 /* Receive status register (Read). */
+#define UART01x_ECR 0x04 /* Error clear register (Write). */
+#define UART010_LCRH 0x08 /* Line control register, high byte. */
+#define ST_UART011_DMAWM 0x08 /* DMA watermark configure register. */
+#define UART010_LCRM 0x0C /* Line control register, middle byte. */
+#define ST_UART011_TIMEOUT 0x0C /* Timeout period register. */
+#define UART010_LCRL 0x10 /* Line control register, low byte. */
+#define UART010_CR 0x14 /* Control register. */
+#define UART01x_FR 0x18 /* Flag register (Read only). */
+#define UART010_IIR 0x1C /* Interrupt identification register (Read). */
+#define UART010_ICR 0x1C /* Interrupt clear register (Write). */
+#define ST_UART011_LCRH_RX 0x1C /* Rx line control register. */
+#define UART01x_ILPR 0x20 /* IrDA low power counter register. */
+#define UART011_IBRD 0x24 /* Integer baud rate divisor register. */
+#define UART011_FBRD 0x28 /* Fractional baud rate divisor register. */
+#define UART011_LCRH 0x2c /* Line control register. */
+#define ST_UART011_LCRH_TX 0x2c /* Tx Line control register. */
+#define UART011_CR 0x30 /* Control register. */
+#define UART011_IFLS 0x34 /* Interrupt fifo level select. */
+#define UART011_IMSC 0x38 /* Interrupt mask. */
+#define UART011_RIS 0x3c /* Raw interrupt status. */
+#define UART011_MIS 0x40 /* Masked interrupt status. */
+#define UART011_ICR 0x44 /* Interrupt clear register. */
+#define UART011_DMACR 0x48 /* DMA control register. */
+#define ST_UART011_XFCR 0x50 /* XON/XOFF control register. */
+#define ST_UART011_XON1 0x54 /* XON1 register. */
+#define ST_UART011_XON2 0x58 /* XON2 register. */
+#define ST_UART011_XOFF1 0x5C /* XON1 register. */
+#define ST_UART011_XOFF2 0x60 /* XON2 register. */
+#define ST_UART011_ITCR 0x80 /* Integration test control register. */
+#define ST_UART011_ITIP 0x84 /* Integration test input register. */
+#define ST_UART011_ABCR 0x100 /* Autobaud control register. */
+#define ST_UART011_ABIMSC 0x15C /* Autobaud interrupt mask/clear register. */
+
+/*
+ * ZTE UART register offsets. This UART has a radically different address
+ * allocation from the ARM and ST variants, so we list all registers here.
+ * We assume unlisted registers do not exist.
+ */
+#define ZX_UART011_DR 0x04
+#define ZX_UART011_FR 0x14
+#define ZX_UART011_IBRD 0x24
+#define ZX_UART011_FBRD 0x28
+#define ZX_UART011_LCRH 0x30
+#define ZX_UART011_CR 0x34
+#define ZX_UART011_IFLS 0x38
+#define ZX_UART011_IMSC 0x40
+#define ZX_UART011_RIS 0x44
+#define ZX_UART011_MIS 0x48
+#define ZX_UART011_ICR 0x4c
+#define ZX_UART011_DMACR 0x50
+
+#define UART011_DR_OE (1 << 11)
+#define UART011_DR_BE (1 << 10)
+#define UART011_DR_PE (1 << 9)
+#define UART011_DR_FE (1 << 8)
+
+#define UART01x_RSR_OE 0x08
+#define UART01x_RSR_BE 0x04
+#define UART01x_RSR_PE 0x02
+#define UART01x_RSR_FE 0x01
+
+#define UART011_FR_RI 0x100
+#define UART011_FR_TXFE 0x080
+#define UART011_FR_RXFF 0x040
+#define UART01x_FR_TXFF 0x020
+#define UART01x_FR_RXFE 0x010
+#define UART01x_FR_BUSY 0x008
+#define UART01x_FR_DCD 0x004
+#define UART01x_FR_DSR 0x002
+#define UART01x_FR_CTS 0x001
+#define UART01x_FR_TMSK (UART01x_FR_TXFF + UART01x_FR_BUSY)
+
+/*
+ * Some bits of Flag Register on ZTE device have different position from
+ * standard ones.
+ */
+#define ZX_UART01x_FR_BUSY 0x100
+#define ZX_UART01x_FR_DSR 0x008
+#define ZX_UART01x_FR_CTS 0x002
+#define ZX_UART011_FR_RI 0x001
+
+#define UART011_CR_CTSEN 0x8000 /* CTS hardware flow control */
+#define UART011_CR_RTSEN 0x4000 /* RTS hardware flow control */
+#define UART011_CR_OUT2 0x2000 /* OUT2 */
+#define UART011_CR_OUT1 0x1000 /* OUT1 */
+#define UART011_CR_RTS 0x0800 /* RTS */
+#define UART011_CR_DTR 0x0400 /* DTR */
+#define UART011_CR_RXE 0x0200 /* receive enable */
+#define UART011_CR_TXE 0x0100 /* transmit enable */
+#define UART011_CR_LBE 0x0080 /* loopback enable */
+#define UART010_CR_RTIE 0x0040
+#define UART010_CR_TIE 0x0020
+#define UART010_CR_RIE 0x0010
+#define UART010_CR_MSIE 0x0008
+#define ST_UART011_CR_OVSFACT 0x0008 /* Oversampling factor */
+#define UART01x_CR_IIRLP 0x0004 /* SIR low power mode */
+#define UART01x_CR_SIREN 0x0002 /* SIR enable */
+#define UART01x_CR_UARTEN 0x0001 /* UART enable */
+
+#define UART011_LCRH_SPS 0x80
+#define UART01x_LCRH_WLEN_8 0x60
+#define UART01x_LCRH_WLEN_7 0x40
+#define UART01x_LCRH_WLEN_6 0x20
+#define UART01x_LCRH_WLEN_5 0x00
+#define UART01x_LCRH_FEN 0x10
+#define UART01x_LCRH_STP2 0x08
+#define UART01x_LCRH_EPS 0x04
+#define UART01x_LCRH_PEN 0x02
+#define UART01x_LCRH_BRK 0x01
+
+#define ST_UART011_DMAWM_RX_1 (0 << 3)
+#define ST_UART011_DMAWM_RX_2 (1 << 3)
+#define ST_UART011_DMAWM_RX_4 (2 << 3)
+#define ST_UART011_DMAWM_RX_8 (3 << 3)
+#define ST_UART011_DMAWM_RX_16 (4 << 3)
+#define ST_UART011_DMAWM_RX_32 (5 << 3)
+#define ST_UART011_DMAWM_RX_48 (6 << 3)
+#define ST_UART011_DMAWM_TX_1 0
+#define ST_UART011_DMAWM_TX_2 1
+#define ST_UART011_DMAWM_TX_4 2
+#define ST_UART011_DMAWM_TX_8 3
+#define ST_UART011_DMAWM_TX_16 4
+#define ST_UART011_DMAWM_TX_32 5
+#define ST_UART011_DMAWM_TX_48 6
+
+#define UART010_IIR_RTIS 0x08
+#define UART010_IIR_TIS 0x04
+#define UART010_IIR_RIS 0x02
+#define UART010_IIR_MIS 0x01
+
+#define UART011_IFLS_RX1_8 (0 << 3)
+#define UART011_IFLS_RX2_8 (1 << 3)
+#define UART011_IFLS_RX4_8 (2 << 3)
+#define UART011_IFLS_RX6_8 (3 << 3)
+#define UART011_IFLS_RX7_8 (4 << 3)
+#define UART011_IFLS_TX1_8 (0 << 0)
+#define UART011_IFLS_TX2_8 (1 << 0)
+#define UART011_IFLS_TX4_8 (2 << 0)
+#define UART011_IFLS_TX6_8 (3 << 0)
+#define UART011_IFLS_TX7_8 (4 << 0)
+/* special values for ST vendor with deeper fifo */
+#define UART011_IFLS_RX_HALF (5 << 3)
+#define UART011_IFLS_TX_HALF (5 << 0)
+
+#define UART011_OEIM (1 << 10) /* overrun error interrupt mask */
+#define UART011_BEIM (1 << 9) /* break error interrupt mask */
+#define UART011_PEIM (1 << 8) /* parity error interrupt mask */
+#define UART011_FEIM (1 << 7) /* framing error interrupt mask */
+#define UART011_RTIM (1 << 6) /* receive timeout interrupt mask */
+#define UART011_TXIM (1 << 5) /* transmit interrupt mask */
+#define UART011_RXIM (1 << 4) /* receive interrupt mask */
+#define UART011_DSRMIM (1 << 3) /* DSR interrupt mask */
+#define UART011_DCDMIM (1 << 2) /* DCD interrupt mask */
+#define UART011_CTSMIM (1 << 1) /* CTS interrupt mask */
+#define UART011_RIMIM (1 << 0) /* RI interrupt mask */
+
+#define UART011_OEIS (1 << 10) /* overrun error interrupt status */
+#define UART011_BEIS (1 << 9) /* break error interrupt status */
+#define UART011_PEIS (1 << 8) /* parity error interrupt status */
+#define UART011_FEIS (1 << 7) /* framing error interrupt status */
+#define UART011_RTIS (1 << 6) /* receive timeout interrupt status */
+#define UART011_TXIS (1 << 5) /* transmit interrupt status */
+#define UART011_RXIS (1 << 4) /* receive interrupt status */
+#define UART011_DSRMIS (1 << 3) /* DSR interrupt status */
+#define UART011_DCDMIS (1 << 2) /* DCD interrupt status */
+#define UART011_CTSMIS (1 << 1) /* CTS interrupt status */
+#define UART011_RIMIS (1 << 0) /* RI interrupt status */
+
+#define UART011_OEIC (1 << 10) /* overrun error interrupt clear */
+#define UART011_BEIC (1 << 9) /* break error interrupt clear */
+#define UART011_PEIC (1 << 8) /* parity error interrupt clear */
+#define UART011_FEIC (1 << 7) /* framing error interrupt clear */
+#define UART011_RTIC (1 << 6) /* receive timeout interrupt clear */
+#define UART011_TXIC (1 << 5) /* transmit interrupt clear */
+#define UART011_RXIC (1 << 4) /* receive interrupt clear */
+#define UART011_DSRMIC (1 << 3) /* DSR interrupt clear */
+#define UART011_DCDMIC (1 << 2) /* DCD interrupt clear */
+#define UART011_CTSMIC (1 << 1) /* CTS interrupt clear */
+#define UART011_RIMIC (1 << 0) /* RI interrupt clear */
+
+#define UART011_DMAONERR (1 << 2) /* disable dma on error */
+#define UART011_TXDMAE (1 << 1) /* enable transmit dma */
+#define UART011_RXDMAE (1 << 0) /* enable receive dma */
+
+#define UART01x_RSR_ANY (UART01x_RSR_OE|UART01x_RSR_BE|UART01x_RSR_PE|UART01x_RSR_FE)
+#define UART01x_FR_MODEM_ANY (UART01x_FR_DCD|UART01x_FR_DSR|UART01x_FR_CTS)
+
+#ifndef __ASSEMBLY__
+struct amba_device; /* in uncompress this is included but amba/bus.h is not */
+struct amba_pl010_data {
+ void (*set_mctrl)(struct amba_device *dev, void __iomem *base, unsigned int mctrl);
+};
+
+struct dma_chan;
+struct amba_pl011_data {
+ bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
+ void *dma_rx_param;
+ void *dma_tx_param;
+ bool dma_rx_poll_enable;
+ unsigned int dma_rx_poll_rate;
+ unsigned int dma_rx_poll_timeout;
+ void (*init) (void);
+ void (*exit) (void);
+};
+#endif
+
+#endif
diff --git a/include/linux/amba/sp810.h b/include/linux/amba/sp810.h
new file mode 100644
index 0000000..58fe9e8
--- /dev/null
+++ b/include/linux/amba/sp810.h
@@ -0,0 +1,62 @@
+/*
+ * ARM PrimeXsys System Controller SP810 header file
+ *
+ * Copyright (C) 2009 ST Microelectronics
+ * Viresh Kumar <vireshk@kernel.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __AMBA_SP810_H
+#define __AMBA_SP810_H
+
+#include <linux/io.h>
+
+/* sysctl registers offset */
+#define SCCTRL 0x000
+#define SCSYSSTAT 0x004
+#define SCIMCTRL 0x008
+#define SCIMSTAT 0x00C
+#define SCXTALCTRL 0x010
+#define SCPLLCTRL 0x014
+#define SCPLLFCTRL 0x018
+#define SCPERCTRL0 0x01C
+#define SCPERCTRL1 0x020
+#define SCPEREN 0x024
+#define SCPERDIS 0x028
+#define SCPERCLKEN 0x02C
+#define SCPERSTAT 0x030
+#define SCSYSID0 0xEE0
+#define SCSYSID1 0xEE4
+#define SCSYSID2 0xEE8
+#define SCSYSID3 0xEEC
+#define SCITCR 0xF00
+#define SCITIR0 0xF04
+#define SCITIR1 0xF08
+#define SCITOR 0xF0C
+#define SCCNTCTRL 0xF10
+#define SCCNTDATA 0xF14
+#define SCCNTSTEP 0xF18
+#define SCPERIPHID0 0xFE0
+#define SCPERIPHID1 0xFE4
+#define SCPERIPHID2 0xFE8
+#define SCPERIPHID3 0xFEC
+#define SCPCELLID0 0xFF0
+#define SCPCELLID1 0xFF4
+#define SCPCELLID2 0xFF8
+#define SCPCELLID3 0xFFC
+
+#define SCCTRL_TIMERENnSEL_SHIFT(n) (15 + ((n) * 2))
+
+static inline void sysctl_soft_reset(void __iomem *base)
+{
+ /* switch to slow mode */
+ writel(0x2, base + SCCTRL);
+
+ /* writing any value to SCSYSSTAT reg will reset system */
+ writel(0, base + SCSYSSTAT);
+}
+
+#endif /* __AMBA_SP810_H */