v4.19.13 snapshot.
diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h
new file mode 100644
index 0000000..87823ac
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3.h
@@ -0,0 +1,443 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * mtu3.h - MediaTek USB3 DRD header
+ *
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#ifndef __MTU3_H__
+#define __MTU3_H__
+
+#include <linux/device.h>
+#include <linux/dmapool.h>
+#include <linux/extcon.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/phy/phy.h>
+#include <linux/regulator/consumer.h>
+#include <linux/usb.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/otg.h>
+
+struct mtu3;
+struct mtu3_ep;
+struct mtu3_request;
+
+#include "mtu3_hw_regs.h"
+#include "mtu3_qmu.h"
+
+#define MU3D_EP_TXCR0(epnum) (U3D_TX1CSR0 + (((epnum) - 1) * 0x10))
+#define MU3D_EP_TXCR1(epnum) (U3D_TX1CSR1 + (((epnum) - 1) * 0x10))
+#define MU3D_EP_TXCR2(epnum) (U3D_TX1CSR2 + (((epnum) - 1) * 0x10))
+
+#define MU3D_EP_RXCR0(epnum) (U3D_RX1CSR0 + (((epnum) - 1) * 0x10))
+#define MU3D_EP_RXCR1(epnum) (U3D_RX1CSR1 + (((epnum) - 1) * 0x10))
+#define MU3D_EP_RXCR2(epnum) (U3D_RX1CSR2 + (((epnum) - 1) * 0x10))
+
+#define USB_QMU_TQHIAR(epnum) (U3D_TXQHIAR1 + (((epnum) - 1) * 0x4))
+#define USB_QMU_RQHIAR(epnum) (U3D_RXQHIAR1 + (((epnum) - 1) * 0x4))
+
+#define USB_QMU_RQCSR(epnum) (U3D_RXQCSR1 + (((epnum) - 1) * 0x10))
+#define USB_QMU_RQSAR(epnum) (U3D_RXQSAR1 + (((epnum) - 1) * 0x10))
+#define USB_QMU_RQCPR(epnum) (U3D_RXQCPR1 + (((epnum) - 1) * 0x10))
+
+#define USB_QMU_TQCSR(epnum) (U3D_TXQCSR1 + (((epnum) - 1) * 0x10))
+#define USB_QMU_TQSAR(epnum) (U3D_TXQSAR1 + (((epnum) - 1) * 0x10))
+#define USB_QMU_TQCPR(epnum) (U3D_TXQCPR1 + (((epnum) - 1) * 0x10))
+
+#define SSUSB_U3_CTRL(p) (U3D_SSUSB_U3_CTRL_0P + ((p) * 0x08))
+#define SSUSB_U2_CTRL(p) (U3D_SSUSB_U2_CTRL_0P + ((p) * 0x08))
+
+#define MTU3_DRIVER_NAME "mtu3"
+#define DMA_ADDR_INVALID (~(dma_addr_t)0)
+
+#define MTU3_EP_ENABLED BIT(0)
+#define MTU3_EP_STALL BIT(1)
+#define MTU3_EP_WEDGE BIT(2)
+#define MTU3_EP_BUSY BIT(3)
+
+#define MTU3_U3_IP_SLOT_DEFAULT 2
+#define MTU3_U2_IP_SLOT_DEFAULT 1
+
+/**
+ * Normally the device works on HS or SS, to simplify fifo management,
+ * devide fifo into some 512B parts, use bitmap to manage it; And
+ * 128 bits size of bitmap is large enough, that means it can manage
+ * up to 64KB fifo size.
+ * NOTE: MTU3_EP_FIFO_UNIT should be power of two
+ */
+#define MTU3_EP_FIFO_UNIT (1 << 9)
+#define MTU3_FIFO_BIT_SIZE 128
+#define MTU3_U2_IP_EP0_FIFO_SIZE 64
+
+/**
+ * Maximum size of ep0 response buffer for ch9 requests,
+ * the SET_SEL request uses 6 so far, and GET_STATUS is 2
+ */
+#define EP0_RESPONSE_BUF 6
+
+/* device operated link and speed got from DEVICE_CONF register */
+enum mtu3_speed {
+ MTU3_SPEED_INACTIVE = 0,
+ MTU3_SPEED_FULL = 1,
+ MTU3_SPEED_HIGH = 3,
+ MTU3_SPEED_SUPER = 4,
+ MTU3_SPEED_SUPER_PLUS = 5,
+};
+
+/**
+ * @MU3D_EP0_STATE_SETUP: waits for SETUP or received a SETUP
+ * without data stage.
+ * @MU3D_EP0_STATE_TX: IN data stage
+ * @MU3D_EP0_STATE_RX: OUT data stage
+ * @MU3D_EP0_STATE_TX_END: the last IN data is transferred, and
+ * waits for its completion interrupt
+ * @MU3D_EP0_STATE_STALL: ep0 is in stall status, will be auto-cleared
+ * after receives a SETUP.
+ */
+enum mtu3_g_ep0_state {
+ MU3D_EP0_STATE_SETUP = 1,
+ MU3D_EP0_STATE_TX,
+ MU3D_EP0_STATE_RX,
+ MU3D_EP0_STATE_TX_END,
+ MU3D_EP0_STATE_STALL,
+};
+
+/**
+ * MTU3_DR_FORCE_NONE: automatically switch host and periperal mode
+ * by IDPIN signal.
+ * MTU3_DR_FORCE_HOST: force to enter host mode and override OTG
+ * IDPIN signal.
+ * MTU3_DR_FORCE_DEVICE: force to enter peripheral mode.
+ */
+enum mtu3_dr_force_mode {
+ MTU3_DR_FORCE_NONE = 0,
+ MTU3_DR_FORCE_HOST,
+ MTU3_DR_FORCE_DEVICE,
+};
+
+/**
+ * @base: the base address of fifo
+ * @limit: the bitmap size in bits
+ * @bitmap: fifo bitmap in unit of @MTU3_EP_FIFO_UNIT
+ */
+struct mtu3_fifo_info {
+ u32 base;
+ u32 limit;
+ DECLARE_BITMAP(bitmap, MTU3_FIFO_BIT_SIZE);
+};
+
+/**
+ * General Purpose Descriptor (GPD):
+ * The format of TX GPD is a little different from RX one.
+ * And the size of GPD is 16 bytes.
+ *
+ * @flag:
+ * bit0: Hardware Own (HWO)
+ * bit1: Buffer Descriptor Present (BDP), always 0, BD is not supported
+ * bit2: Bypass (BPS), 1: HW skips this GPD if HWO = 1
+ * bit7: Interrupt On Completion (IOC)
+ * @chksum: This is used to validate the contents of this GPD;
+ * If TXQ_CS_EN / RXQ_CS_EN bit is set, an interrupt is issued
+ * when checksum validation fails;
+ * Checksum value is calculated over the 16 bytes of the GPD by default;
+ * @data_buf_len (RX ONLY): This value indicates the length of
+ * the assigned data buffer
+ * @tx_ext_addr (TX ONLY): [3:0] are 4 extension bits of @buffer,
+ * [7:4] are 4 extension bits of @next_gpd
+ * @next_gpd: Physical address of the next GPD
+ * @buffer: Physical address of the data buffer
+ * @buf_len:
+ * (TX): This value indicates the length of the assigned data buffer
+ * (RX): The total length of data received
+ * @ext_len: reserved
+ * @rx_ext_addr(RX ONLY): [3:0] are 4 extension bits of @buffer,
+ * [7:4] are 4 extension bits of @next_gpd
+ * @ext_flag:
+ * bit5 (TX ONLY): Zero Length Packet (ZLP),
+ */
+struct qmu_gpd {
+ __u8 flag;
+ __u8 chksum;
+ union {
+ __le16 data_buf_len;
+ __le16 tx_ext_addr;
+ };
+ __le32 next_gpd;
+ __le32 buffer;
+ __le16 buf_len;
+ union {
+ __u8 ext_len;
+ __u8 rx_ext_addr;
+ };
+ __u8 ext_flag;
+} __packed;
+
+/**
+* dma: physical base address of GPD segment
+* start: virtual base address of GPD segment
+* end: the last GPD element
+* enqueue: the first empty GPD to use
+* dequeue: the first completed GPD serviced by ISR
+* NOTE: the size of GPD ring should be >= 2
+*/
+struct mtu3_gpd_ring {
+ dma_addr_t dma;
+ struct qmu_gpd *start;
+ struct qmu_gpd *end;
+ struct qmu_gpd *enqueue;
+ struct qmu_gpd *dequeue;
+};
+
+/**
+* @vbus: vbus 5V used by host mode
+* @edev: external connector used to detect vbus and iddig changes
+* @vbus_nb: notifier for vbus detection
+* @vbus_work : work of vbus detection notifier, used to avoid sleep in
+* notifier callback which is atomic context
+* @vbus_event : event of vbus detecion notifier
+* @id_nb : notifier for iddig(idpin) detection
+* @id_work : work of iddig detection notifier
+* @id_event : event of iddig detecion notifier
+* @is_u3_drd: whether port0 supports usb3.0 dual-role device or not
+* @manual_drd_enabled: it's true when supports dual-role device by debugfs
+* to switch host/device modes depending on user input.
+*/
+struct otg_switch_mtk {
+ struct regulator *vbus;
+ struct extcon_dev *edev;
+ struct notifier_block vbus_nb;
+ struct work_struct vbus_work;
+ unsigned long vbus_event;
+ struct notifier_block id_nb;
+ struct work_struct id_work;
+ unsigned long id_event;
+ bool is_u3_drd;
+ bool manual_drd_enabled;
+};
+
+/**
+ * @mac_base: register base address of device MAC, exclude xHCI's
+ * @ippc_base: register base address of IP Power and Clock interface (IPPC)
+ * @vusb33: usb3.3V shared by device/host IP
+ * @sys_clk: system clock of mtu3, shared by device/host IP
+ * @ref_clk: reference clock
+ * @mcu_clk: mcu_bus_ck clock for AHB bus etc
+ * @dma_clk: dma_bus_ck clock for AXI bus etc
+ * @dr_mode: works in which mode:
+ * host only, device only or dual-role mode
+ * @u2_ports: number of usb2.0 host ports
+ * @u3_ports: number of usb3.0 host ports
+ * @u3p_dis_msk: mask of disabling usb3 ports, for example, bit0==1 to
+ * disable u3port0, bit1==1 to disable u3port1,... etc
+ * @dbgfs_root: only used when supports manual dual-role switch via debugfs
+ * @uwk_en: it's true when supports remote wakeup in host mode
+ * @uwk: syscon including usb wakeup glue layer between SSUSB IP and SPM
+ * @uwk_reg_base: the base address of the wakeup glue layer in @uwk
+ * @uwk_vers: the version of the wakeup glue layer
+ */
+struct ssusb_mtk {
+ struct device *dev;
+ struct mtu3 *u3d;
+ void __iomem *mac_base;
+ void __iomem *ippc_base;
+ struct phy **phys;
+ int num_phys;
+ /* common power & clock */
+ struct regulator *vusb33;
+ struct clk *sys_clk;
+ struct clk *ref_clk;
+ struct clk *mcu_clk;
+ struct clk *dma_clk;
+ /* otg */
+ struct otg_switch_mtk otg_switch;
+ enum usb_dr_mode dr_mode;
+ bool is_host;
+ int u2_ports;
+ int u3_ports;
+ int u3p_dis_msk;
+ struct dentry *dbgfs_root;
+ /* usb wakeup for host mode */
+ bool uwk_en;
+ struct regmap *uwk;
+ u32 uwk_reg_base;
+ u32 uwk_vers;
+};
+
+/**
+ * @fifo_size: it is (@slot + 1) * @fifo_seg_size
+ * @fifo_seg_size: it is roundup_pow_of_two(@maxp)
+ */
+struct mtu3_ep {
+ struct usb_ep ep;
+ char name[12];
+ struct mtu3 *mtu;
+ u8 epnum;
+ u8 type;
+ u8 is_in;
+ u16 maxp;
+ int slot;
+ u32 fifo_size;
+ u32 fifo_addr;
+ u32 fifo_seg_size;
+ struct mtu3_fifo_info *fifo;
+
+ struct list_head req_list;
+ struct mtu3_gpd_ring gpd_ring;
+ const struct usb_ss_ep_comp_descriptor *comp_desc;
+ const struct usb_endpoint_descriptor *desc;
+
+ int flags;
+ u8 wedged;
+ u8 busy;
+};
+
+struct mtu3_request {
+ struct usb_request request;
+ struct list_head list;
+ struct mtu3_ep *mep;
+ struct mtu3 *mtu;
+ struct qmu_gpd *gpd;
+ int epnum;
+};
+
+static inline struct ssusb_mtk *dev_to_ssusb(struct device *dev)
+{
+ return dev_get_drvdata(dev);
+}
+
+/**
+ * struct mtu3 - device driver instance data.
+ * @slot: MTU3_U2_IP_SLOT_DEFAULT for U2 IP only,
+ * MTU3_U3_IP_SLOT_DEFAULT for U3 IP
+ * @may_wakeup: means device's remote wakeup is enabled
+ * @is_self_powered: is reported in device status and the config descriptor
+ * @delayed_status: true when function drivers ask for delayed status
+ * @ep0_req: dummy request used while handling standard USB requests
+ * for GET_STATUS and SET_SEL
+ * @setup_buf: ep0 response buffer for GET_STATUS and SET_SEL requests
+ */
+struct mtu3 {
+ spinlock_t lock;
+ struct ssusb_mtk *ssusb;
+ struct device *dev;
+ void __iomem *mac_base;
+ void __iomem *ippc_base;
+ int irq;
+
+ struct mtu3_fifo_info tx_fifo;
+ struct mtu3_fifo_info rx_fifo;
+
+ struct mtu3_ep *ep_array;
+ struct mtu3_ep *in_eps;
+ struct mtu3_ep *out_eps;
+ struct mtu3_ep *ep0;
+ int num_eps;
+ int slot;
+ int active_ep;
+
+ struct dma_pool *qmu_gpd_pool;
+ enum mtu3_g_ep0_state ep0_state;
+ struct usb_gadget g; /* the gadget */
+ struct usb_gadget_driver *gadget_driver;
+ struct mtu3_request ep0_req;
+ u8 setup_buf[EP0_RESPONSE_BUF];
+ u32 max_speed;
+
+ unsigned is_active:1;
+ unsigned may_wakeup:1;
+ unsigned is_self_powered:1;
+ unsigned test_mode:1;
+ unsigned softconnect:1;
+ unsigned u1_enable:1;
+ unsigned u2_enable:1;
+ unsigned is_u3_ip:1;
+ unsigned delayed_status:1;
+
+ u8 address;
+ u8 test_mode_nr;
+ u32 hw_version;
+};
+
+static inline struct mtu3 *gadget_to_mtu3(struct usb_gadget *g)
+{
+ return container_of(g, struct mtu3, g);
+}
+
+static inline int is_first_entry(const struct list_head *list,
+ const struct list_head *head)
+{
+ return list_is_last(head, list);
+}
+
+static inline struct mtu3_request *to_mtu3_request(struct usb_request *req)
+{
+ return req ? container_of(req, struct mtu3_request, request) : NULL;
+}
+
+static inline struct mtu3_ep *to_mtu3_ep(struct usb_ep *ep)
+{
+ return ep ? container_of(ep, struct mtu3_ep, ep) : NULL;
+}
+
+static inline struct mtu3_request *next_request(struct mtu3_ep *mep)
+{
+ return list_first_entry_or_null(&mep->req_list, struct mtu3_request,
+ list);
+}
+
+static inline void mtu3_writel(void __iomem *base, u32 offset, u32 data)
+{
+ writel(data, base + offset);
+}
+
+static inline u32 mtu3_readl(void __iomem *base, u32 offset)
+{
+ return readl(base + offset);
+}
+
+static inline void mtu3_setbits(void __iomem *base, u32 offset, u32 bits)
+{
+ void __iomem *addr = base + offset;
+ u32 tmp = readl(addr);
+
+ writel((tmp | (bits)), addr);
+}
+
+static inline void mtu3_clrbits(void __iomem *base, u32 offset, u32 bits)
+{
+ void __iomem *addr = base + offset;
+ u32 tmp = readl(addr);
+
+ writel((tmp & ~(bits)), addr);
+}
+
+int ssusb_check_clocks(struct ssusb_mtk *ssusb, u32 ex_clks);
+struct usb_request *mtu3_alloc_request(struct usb_ep *ep, gfp_t gfp_flags);
+void mtu3_free_request(struct usb_ep *ep, struct usb_request *req);
+void mtu3_req_complete(struct mtu3_ep *mep,
+ struct usb_request *req, int status);
+
+int mtu3_config_ep(struct mtu3 *mtu, struct mtu3_ep *mep,
+ int interval, int burst, int mult);
+void mtu3_deconfig_ep(struct mtu3 *mtu, struct mtu3_ep *mep);
+void mtu3_ep_stall_set(struct mtu3_ep *mep, bool set);
+void mtu3_ep0_setup(struct mtu3 *mtu);
+void mtu3_start(struct mtu3 *mtu);
+void mtu3_stop(struct mtu3 *mtu);
+void mtu3_dev_on_off(struct mtu3 *mtu, int is_on);
+
+int mtu3_gadget_setup(struct mtu3 *mtu);
+void mtu3_gadget_cleanup(struct mtu3 *mtu);
+void mtu3_gadget_reset(struct mtu3 *mtu);
+void mtu3_gadget_suspend(struct mtu3 *mtu);
+void mtu3_gadget_resume(struct mtu3 *mtu);
+void mtu3_gadget_disconnect(struct mtu3 *mtu);
+
+irqreturn_t mtu3_ep0_isr(struct mtu3 *mtu);
+extern const struct usb_ep_ops mtu3_ep0_ops;
+
+#endif