v4.19.13 snapshot.
diff --git a/drivers/tty/serial/arc_uart.c b/drivers/tty/serial/arc_uart.c
new file mode 100644
index 0000000..d904a3a
--- /dev/null
+++ b/drivers/tty/serial/arc_uart.c
@@ -0,0 +1,688 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ARC On-Chip(fpga) UART Driver
+ *
+ * Copyright (C) 2010-2012 Synopsys, Inc. (www.synopsys.com)
+ *
+ * vineetg: July 10th 2012
+ * -Decoupled the driver from arch/arc
+ * +Using platform_get_resource() for irq/membase (thx to bfin_uart.c)
+ * +Using early_platform_xxx() for early console (thx to mach-shmobile/xxx)
+ *
+ * Vineetg: Aug 21st 2010
+ * -Is uart_tx_stopped() not done in tty write path as it has already been
+ * taken care of, in serial core
+ *
+ * Vineetg: Aug 18th 2010
+ * -New Serial Core based ARC UART driver
+ * -Derived largely from blackfin driver albiet with some major tweaks
+ *
+ * TODO:
+ * -check if sysreq works
+ */
+
+#if defined(CONFIG_SERIAL_ARC_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/serial.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/io.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+
+/*************************************
+ * ARC UART Hardware Specs
+ ************************************/
+#define ARC_UART_TX_FIFO_SIZE 1
+
+/*
+ * UART Register set (this is not a Standards Compliant IP)
+ * Also each reg is Word aligned, but only 8 bits wide
+ */
+#define R_ID0 0
+#define R_ID1 4
+#define R_ID2 8
+#define R_ID3 12
+#define R_DATA 16
+#define R_STS 20
+#define R_BAUDL 24
+#define R_BAUDH 28
+
+/* Bits for UART Status Reg (R/W) */
+#define RXIENB 0x04 /* Receive Interrupt Enable */
+#define TXIENB 0x40 /* Transmit Interrupt Enable */
+
+#define RXEMPTY 0x20 /* Receive FIFO Empty: No char receivede */
+#define TXEMPTY 0x80 /* Transmit FIFO Empty, thus char can be written into */
+
+#define RXFULL 0x08 /* Receive FIFO full */
+#define RXFULL1 0x10 /* Receive FIFO has space for 1 char (tot space=4) */
+
+#define RXFERR 0x01 /* Frame Error: Stop Bit not detected */
+#define RXOERR 0x02 /* OverFlow Err: Char recv but RXFULL still set */
+
+/* Uart bit fiddling helpers: lowest level */
+#define RBASE(port, reg) (port->membase + reg)
+#define UART_REG_SET(u, r, v) writeb((v), RBASE(u, r))
+#define UART_REG_GET(u, r) readb(RBASE(u, r))
+
+#define UART_REG_OR(u, r, v) UART_REG_SET(u, r, UART_REG_GET(u, r) | (v))
+#define UART_REG_CLR(u, r, v) UART_REG_SET(u, r, UART_REG_GET(u, r) & ~(v))
+
+/* Uart bit fiddling helpers: API level */
+#define UART_SET_DATA(uart, val) UART_REG_SET(uart, R_DATA, val)
+#define UART_GET_DATA(uart) UART_REG_GET(uart, R_DATA)
+
+#define UART_SET_BAUDH(uart, val) UART_REG_SET(uart, R_BAUDH, val)
+#define UART_SET_BAUDL(uart, val) UART_REG_SET(uart, R_BAUDL, val)
+
+#define UART_CLR_STATUS(uart, val) UART_REG_CLR(uart, R_STS, val)
+#define UART_GET_STATUS(uart) UART_REG_GET(uart, R_STS)
+
+#define UART_ALL_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, RXIENB|TXIENB)
+#define UART_RX_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, RXIENB)
+#define UART_TX_IRQ_DISABLE(uart) UART_REG_CLR(uart, R_STS, TXIENB)
+
+#define UART_ALL_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, RXIENB|TXIENB)
+#define UART_RX_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, RXIENB)
+#define UART_TX_IRQ_ENABLE(uart) UART_REG_OR(uart, R_STS, TXIENB)
+
+#define ARC_SERIAL_DEV_NAME "ttyARC"
+
+struct arc_uart_port {
+ struct uart_port port;
+ unsigned long baud;
+};
+
+#define to_arc_port(uport) container_of(uport, struct arc_uart_port, port)
+
+static struct arc_uart_port arc_uart_ports[CONFIG_SERIAL_ARC_NR_PORTS];
+
+#ifdef CONFIG_SERIAL_ARC_CONSOLE
+static struct console arc_console;
+#endif
+
+#define DRIVER_NAME "arc-uart"
+
+static struct uart_driver arc_uart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = DRIVER_NAME,
+ .dev_name = ARC_SERIAL_DEV_NAME,
+ .major = 0,
+ .minor = 0,
+ .nr = CONFIG_SERIAL_ARC_NR_PORTS,
+#ifdef CONFIG_SERIAL_ARC_CONSOLE
+ .cons = &arc_console,
+#endif
+};
+
+static void arc_serial_stop_rx(struct uart_port *port)
+{
+ UART_RX_IRQ_DISABLE(port);
+}
+
+static void arc_serial_stop_tx(struct uart_port *port)
+{
+ while (!(UART_GET_STATUS(port) & TXEMPTY))
+ cpu_relax();
+
+ UART_TX_IRQ_DISABLE(port);
+}
+
+/*
+ * Return TIOCSER_TEMT when transmitter is not busy.
+ */
+static unsigned int arc_serial_tx_empty(struct uart_port *port)
+{
+ unsigned int stat;
+
+ stat = UART_GET_STATUS(port);
+ if (stat & TXEMPTY)
+ return TIOCSER_TEMT;
+
+ return 0;
+}
+
+/*
+ * Driver internal routine, used by both tty(serial core) as well as tx-isr
+ * -Called under spinlock in either cases
+ * -also tty->stopped has already been checked
+ * = by uart_start( ) before calling us
+ * = tx_ist checks that too before calling
+ */
+static void arc_serial_tx_chars(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->state->xmit;
+ int sent = 0;
+ unsigned char ch;
+
+ if (unlikely(port->x_char)) {
+ UART_SET_DATA(port, port->x_char);
+ port->icount.tx++;
+ port->x_char = 0;
+ sent = 1;
+ } else if (!uart_circ_empty(xmit)) {
+ ch = xmit->buf[xmit->tail];
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ while (!(UART_GET_STATUS(port) & TXEMPTY))
+ cpu_relax();
+ UART_SET_DATA(port, ch);
+ sent = 1;
+ }
+
+ /*
+ * If num chars in xmit buffer are too few, ask tty layer for more.
+ * By Hard ISR to schedule processing in software interrupt part
+ */
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (sent)
+ UART_TX_IRQ_ENABLE(port);
+}
+
+/*
+ * port is locked and interrupts are disabled
+ * uart_start( ) calls us under the port spinlock irqsave
+ */
+static void arc_serial_start_tx(struct uart_port *port)
+{
+ arc_serial_tx_chars(port);
+}
+
+static void arc_serial_rx_chars(struct uart_port *port, unsigned int status)
+{
+ unsigned int ch, flg = 0;
+
+ /*
+ * UART has 4 deep RX-FIFO. Driver's recongnition of this fact
+ * is very subtle. Here's how ...
+ * Upon getting a RX-Intr, such that RX-EMPTY=0, meaning data available,
+ * driver reads the DATA Reg and keeps doing that in a loop, until
+ * RX-EMPTY=1. Multiple chars being avail, with a single Interrupt,
+ * before RX-EMPTY=0, implies some sort of buffering going on in the
+ * controller, which is indeed the Rx-FIFO.
+ */
+ do {
+ /*
+ * This could be an Rx Intr for err (no data),
+ * so check err and clear that Intr first
+ */
+ if (unlikely(status & (RXOERR | RXFERR))) {
+ if (status & RXOERR) {
+ port->icount.overrun++;
+ flg = TTY_OVERRUN;
+ UART_CLR_STATUS(port, RXOERR);
+ }
+
+ if (status & RXFERR) {
+ port->icount.frame++;
+ flg = TTY_FRAME;
+ UART_CLR_STATUS(port, RXFERR);
+ }
+ } else
+ flg = TTY_NORMAL;
+
+ if (status & RXEMPTY)
+ continue;
+
+ ch = UART_GET_DATA(port);
+ port->icount.rx++;
+
+ if (!(uart_handle_sysrq_char(port, ch)))
+ uart_insert_char(port, status, RXOERR, ch, flg);
+
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(&port->state->port);
+ spin_lock(&port->lock);
+ } while (!((status = UART_GET_STATUS(port)) & RXEMPTY));
+}
+
+/*
+ * A note on the Interrupt handling state machine of this driver
+ *
+ * kernel printk writes funnel thru the console driver framework and in order
+ * to keep things simple as well as efficient, it writes to UART in polled
+ * mode, in one shot, and exits.
+ *
+ * OTOH, Userland output (via tty layer), uses interrupt based writes as there
+ * can be undeterministic delay between char writes.
+ *
+ * Thus Rx-interrupts are always enabled, while tx-interrupts are by default
+ * disabled.
+ *
+ * When tty has some data to send out, serial core calls driver's start_tx
+ * which
+ * -checks-if-tty-buffer-has-char-to-send
+ * -writes-data-to-uart
+ * -enable-tx-intr
+ *
+ * Once data bits are pushed out, controller raises the Tx-room-avail-Interrupt.
+ * The first thing Tx ISR does is disable further Tx interrupts (as this could
+ * be the last char to send, before settling down into the quiet polled mode).
+ * It then calls the exact routine used by tty layer write to send out any
+ * more char in tty buffer. In case of sending, it re-enables Tx-intr. In case
+ * of no data, it remains disabled.
+ * This is how the transmit state machine is dynamically switched on/off
+ */
+
+static irqreturn_t arc_serial_isr(int irq, void *dev_id)
+{
+ struct uart_port *port = dev_id;
+ unsigned int status;
+
+ status = UART_GET_STATUS(port);
+
+ /*
+ * Single IRQ for both Rx (data available) Tx (room available) Interrupt
+ * notifications from the UART Controller.
+ * To demultiplex between the two, we check the relevant bits
+ */
+ if (status & RXIENB) {
+
+ /* already in ISR, no need of xx_irqsave */
+ spin_lock(&port->lock);
+ arc_serial_rx_chars(port, status);
+ spin_unlock(&port->lock);
+ }
+
+ if ((status & TXIENB) && (status & TXEMPTY)) {
+
+ /* Unconditionally disable further Tx-Interrupts.
+ * will be enabled by tx_chars() if needed.
+ */
+ UART_TX_IRQ_DISABLE(port);
+
+ spin_lock(&port->lock);
+
+ if (!uart_tx_stopped(port))
+ arc_serial_tx_chars(port);
+
+ spin_unlock(&port->lock);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static unsigned int arc_serial_get_mctrl(struct uart_port *port)
+{
+ /*
+ * Pretend we have a Modem status reg and following bits are
+ * always set, to satify the serial core state machine
+ * (DSR) Data Set Ready
+ * (CTS) Clear To Send
+ * (CAR) Carrier Detect
+ */
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void arc_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ /* MCR not present */
+}
+
+static void arc_serial_break_ctl(struct uart_port *port, int break_state)
+{
+ /* ARC UART doesn't support sending Break signal */
+}
+
+static int arc_serial_startup(struct uart_port *port)
+{
+ /* Before we hook up the ISR, Disable all UART Interrupts */
+ UART_ALL_IRQ_DISABLE(port);
+
+ if (request_irq(port->irq, arc_serial_isr, 0, "arc uart rx-tx", port)) {
+ dev_warn(port->dev, "Unable to attach ARC UART intr\n");
+ return -EBUSY;
+ }
+
+ UART_RX_IRQ_ENABLE(port); /* Only Rx IRQ enabled to begin with */
+
+ return 0;
+}
+
+/* This is not really needed */
+static void arc_serial_shutdown(struct uart_port *port)
+{
+ free_irq(port->irq, port);
+}
+
+static void
+arc_serial_set_termios(struct uart_port *port, struct ktermios *new,
+ struct ktermios *old)
+{
+ struct arc_uart_port *uart = to_arc_port(port);
+ unsigned int baud, uartl, uarth, hw_val;
+ unsigned long flags;
+
+ /*
+ * Use the generic handler so that any specially encoded baud rates
+ * such as SPD_xx flags or "%B0" can be handled
+ * Max Baud I suppose will not be more than current 115K * 4
+ * Formula for ARC UART is: hw-val = ((CLK/(BAUD*4)) -1)
+ * spread over two 8-bit registers
+ */
+ baud = uart_get_baud_rate(port, new, old, 0, 460800);
+
+ hw_val = port->uartclk / (uart->baud * 4) - 1;
+ uartl = hw_val & 0xFF;
+ uarth = (hw_val >> 8) & 0xFF;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ UART_ALL_IRQ_DISABLE(port);
+
+ UART_SET_BAUDL(port, uartl);
+ UART_SET_BAUDH(port, uarth);
+
+ UART_RX_IRQ_ENABLE(port);
+
+ /*
+ * UART doesn't support Parity/Hardware Flow Control;
+ * Only supports 8N1 character size
+ */
+ new->c_cflag &= ~(CMSPAR|CRTSCTS|CSIZE);
+ new->c_cflag |= CS8;
+
+ if (old)
+ tty_termios_copy_hw(new, old);
+
+ /* Don't rewrite B0 */
+ if (tty_termios_baud_rate(new))
+ tty_termios_encode_baud_rate(new, baud, baud);
+
+ uart_update_timeout(port, new->c_cflag, baud);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *arc_serial_type(struct uart_port *port)
+{
+ return port->type == PORT_ARC ? DRIVER_NAME : NULL;
+}
+
+static void arc_serial_release_port(struct uart_port *port)
+{
+}
+
+static int arc_serial_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+/*
+ * Verify the new serial_struct (for TIOCSSERIAL).
+ */
+static int
+arc_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ if (port->type != PORT_UNKNOWN && ser->type != PORT_ARC)
+ return -EINVAL;
+
+ return 0;
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void arc_serial_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE)
+ port->type = PORT_ARC;
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+
+static void arc_serial_poll_putchar(struct uart_port *port, unsigned char chr)
+{
+ while (!(UART_GET_STATUS(port) & TXEMPTY))
+ cpu_relax();
+
+ UART_SET_DATA(port, chr);
+}
+
+static int arc_serial_poll_getchar(struct uart_port *port)
+{
+ unsigned char chr;
+
+ while (!(UART_GET_STATUS(port) & RXEMPTY))
+ cpu_relax();
+
+ chr = UART_GET_DATA(port);
+ return chr;
+}
+#endif
+
+static const struct uart_ops arc_serial_pops = {
+ .tx_empty = arc_serial_tx_empty,
+ .set_mctrl = arc_serial_set_mctrl,
+ .get_mctrl = arc_serial_get_mctrl,
+ .stop_tx = arc_serial_stop_tx,
+ .start_tx = arc_serial_start_tx,
+ .stop_rx = arc_serial_stop_rx,
+ .break_ctl = arc_serial_break_ctl,
+ .startup = arc_serial_startup,
+ .shutdown = arc_serial_shutdown,
+ .set_termios = arc_serial_set_termios,
+ .type = arc_serial_type,
+ .release_port = arc_serial_release_port,
+ .request_port = arc_serial_request_port,
+ .config_port = arc_serial_config_port,
+ .verify_port = arc_serial_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_put_char = arc_serial_poll_putchar,
+ .poll_get_char = arc_serial_poll_getchar,
+#endif
+};
+
+#ifdef CONFIG_SERIAL_ARC_CONSOLE
+
+static int arc_serial_console_setup(struct console *co, char *options)
+{
+ struct uart_port *port;
+ int baud = 115200;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index < 0 || co->index >= CONFIG_SERIAL_ARC_NR_PORTS)
+ return -ENODEV;
+
+ /*
+ * The uart port backing the console (e.g. ttyARC1) might not have been
+ * init yet. If so, defer the console setup to after the port.
+ */
+ port = &arc_uart_ports[co->index].port;
+ if (!port->membase)
+ return -ENODEV;
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ /*
+ * Serial core will call port->ops->set_termios( )
+ * which will set the baud reg
+ */
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static void arc_serial_console_putchar(struct uart_port *port, int ch)
+{
+ while (!(UART_GET_STATUS(port) & TXEMPTY))
+ cpu_relax();
+
+ UART_SET_DATA(port, (unsigned char)ch);
+}
+
+/*
+ * Interrupts are disabled on entering
+ */
+static void arc_serial_console_write(struct console *co, const char *s,
+ unsigned int count)
+{
+ struct uart_port *port = &arc_uart_ports[co->index].port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+ uart_console_write(port, s, count, arc_serial_console_putchar);
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static struct console arc_console = {
+ .name = ARC_SERIAL_DEV_NAME,
+ .write = arc_serial_console_write,
+ .device = uart_console_device,
+ .setup = arc_serial_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &arc_uart_driver
+};
+
+static void arc_early_serial_write(struct console *con, const char *s,
+ unsigned int n)
+{
+ struct earlycon_device *dev = con->data;
+
+ uart_console_write(&dev->port, s, n, arc_serial_console_putchar);
+}
+
+static int __init arc_early_console_setup(struct earlycon_device *dev,
+ const char *opt)
+{
+ struct uart_port *port = &dev->port;
+ unsigned int l, h, hw_val;
+
+ if (!dev->port.membase)
+ return -ENODEV;
+
+ hw_val = port->uartclk / (dev->baud * 4) - 1;
+ l = hw_val & 0xFF;
+ h = (hw_val >> 8) & 0xFF;
+
+ UART_SET_BAUDL(port, l);
+ UART_SET_BAUDH(port, h);
+
+ dev->con->write = arc_early_serial_write;
+ return 0;
+}
+OF_EARLYCON_DECLARE(arc_uart, "snps,arc-uart", arc_early_console_setup);
+
+#endif /* CONFIG_SERIAL_ARC_CONSOLE */
+
+static int arc_serial_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct arc_uart_port *uart;
+ struct uart_port *port;
+ int dev_id;
+ u32 val;
+
+ /* no device tree device */
+ if (!np)
+ return -ENODEV;
+
+ dev_id = of_alias_get_id(np, "serial");
+ if (dev_id < 0)
+ dev_id = 0;
+
+ if (dev_id >= ARRAY_SIZE(arc_uart_ports)) {
+ dev_err(&pdev->dev, "serial%d out of range\n", dev_id);
+ return -EINVAL;
+ }
+
+ uart = &arc_uart_ports[dev_id];
+ port = &uart->port;
+
+ if (of_property_read_u32(np, "clock-frequency", &val)) {
+ dev_err(&pdev->dev, "clock-frequency property NOTset\n");
+ return -EINVAL;
+ }
+ port->uartclk = val;
+
+ if (of_property_read_u32(np, "current-speed", &val)) {
+ dev_err(&pdev->dev, "current-speed property NOT set\n");
+ return -EINVAL;
+ }
+ uart->baud = val;
+
+ port->membase = of_iomap(np, 0);
+ if (!port->membase)
+ /* No point of dev_err since UART itself is hosed here */
+ return -ENXIO;
+
+ port->irq = irq_of_parse_and_map(np, 0);
+
+ port->dev = &pdev->dev;
+ port->iotype = UPIO_MEM;
+ port->flags = UPF_BOOT_AUTOCONF;
+ port->line = dev_id;
+ port->ops = &arc_serial_pops;
+
+ port->fifosize = ARC_UART_TX_FIFO_SIZE;
+
+ /*
+ * uart_insert_char( ) uses it in decideding whether to ignore a
+ * char or not. Explicitly setting it here, removes the subtelty
+ */
+ port->ignore_status_mask = 0;
+
+ return uart_add_one_port(&arc_uart_driver, &arc_uart_ports[dev_id].port);
+}
+
+static int arc_serial_remove(struct platform_device *pdev)
+{
+ /* This will never be called */
+ return 0;
+}
+
+static const struct of_device_id arc_uart_dt_ids[] = {
+ { .compatible = "snps,arc-uart" },
+ { /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, arc_uart_dt_ids);
+
+static struct platform_driver arc_platform_driver = {
+ .probe = arc_serial_probe,
+ .remove = arc_serial_remove,
+ .driver = {
+ .name = DRIVER_NAME,
+ .of_match_table = arc_uart_dt_ids,
+ },
+};
+
+static int __init arc_serial_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&arc_uart_driver);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&arc_platform_driver);
+ if (ret)
+ uart_unregister_driver(&arc_uart_driver);
+
+ return ret;
+}
+
+static void __exit arc_serial_exit(void)
+{
+ platform_driver_unregister(&arc_platform_driver);
+ uart_unregister_driver(&arc_uart_driver);
+}
+
+module_init(arc_serial_init);
+module_exit(arc_serial_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_AUTHOR("Vineet Gupta");
+MODULE_DESCRIPTION("ARC(Synopsys) On-Chip(fpga) serial driver");