v4.19.13 snapshot.
diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
new file mode 100644
index 0000000..632a0e7
--- /dev/null
+++ b/drivers/phy/qualcomm/Kconfig
@@ -0,0 +1,67 @@
+#
+# Phy drivers for Qualcomm and Atheros platforms
+#
+config PHY_ATH79_USB
+ tristate "Atheros AR71XX/9XXX USB PHY driver"
+ depends on OF && (ATH79 || COMPILE_TEST)
+ default y if USB_EHCI_HCD_PLATFORM || USB_OHCI_HCD_PLATFORM
+ select RESET_CONTROLLER
+ select GENERIC_PHY
+ help
+ Enable this to support the USB PHY on Atheros AR71XX/9XXX SoCs.
+
+config PHY_QCOM_APQ8064_SATA
+ tristate "Qualcomm APQ8064 SATA SerDes/PHY driver"
+ depends on ARCH_QCOM
+ depends on HAS_IOMEM
+ depends on OF
+ select GENERIC_PHY
+
+config PHY_QCOM_IPQ806X_SATA
+ tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
+ depends on ARCH_QCOM
+ depends on HAS_IOMEM
+ depends on OF
+ select GENERIC_PHY
+
+config PHY_QCOM_QMP
+ tristate "Qualcomm QMP PHY Driver"
+ depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST)
+ select GENERIC_PHY
+ help
+ Enable this to support the QMP PHY transceiver that is used
+ with controllers such as PCIe, UFS, and USB on Qualcomm chips.
+
+config PHY_QCOM_QUSB2
+ tristate "Qualcomm QUSB2 PHY Driver"
+ depends on OF && (ARCH_QCOM || COMPILE_TEST)
+ depends on NVMEM || !NVMEM
+ select GENERIC_PHY
+ help
+ Enable this to support the HighSpeed QUSB2 PHY transceiver for USB
+ controllers on Qualcomm chips. This driver supports the high-speed
+ PHY which is usually paired with either the ChipIdea or Synopsys DWC3
+ USB IPs on MSM SOCs.
+
+config PHY_QCOM_UFS
+ tristate "Qualcomm UFS PHY driver"
+ depends on OF && ARCH_QCOM
+ select GENERIC_PHY
+ help
+ Support for UFS PHY on QCOM chipsets.
+
+config PHY_QCOM_USB_HS
+ tristate "Qualcomm USB HS PHY module"
+ depends on USB_ULPI_BUS
+ depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+ select GENERIC_PHY
+ help
+ Support for the USB high-speed ULPI compliant phy on Qualcomm
+ chipsets.
+
+config PHY_QCOM_USB_HSIC
+ tristate "Qualcomm USB HSIC ULPI PHY module"
+ depends on USB_ULPI_BUS
+ select GENERIC_PHY
+ help
+ Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
new file mode 100644
index 0000000..deb831f
--- /dev/null
+++ b/drivers/phy/qualcomm/Makefile
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_PHY_ATH79_USB) += phy-ath79-usb.o
+obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
+obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
+obj-$(CONFIG_PHY_QCOM_QMP) += phy-qcom-qmp.o
+obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o
+obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
+obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HS) += phy-qcom-usb-hs.o
+obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
diff --git a/drivers/phy/qualcomm/phy-ath79-usb.c b/drivers/phy/qualcomm/phy-ath79-usb.c
new file mode 100644
index 0000000..6fd6e07
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-ath79-usb.c
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Atheros AR71XX/9XXX USB PHY driver
+ *
+ * Copyright (C) 2015-2018 Alban Bedel <albeu@free.fr>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/reset.h>
+
+struct ath79_usb_phy {
+ struct reset_control *reset;
+ /* The suspend override logic is inverted, hence the no prefix
+ * to make the code a bit easier to understand.
+ */
+ struct reset_control *no_suspend_override;
+};
+
+static int ath79_usb_phy_power_on(struct phy *phy)
+{
+ struct ath79_usb_phy *priv = phy_get_drvdata(phy);
+ int err = 0;
+
+ if (priv->no_suspend_override) {
+ err = reset_control_assert(priv->no_suspend_override);
+ if (err)
+ return err;
+ }
+
+ err = reset_control_deassert(priv->reset);
+ if (err && priv->no_suspend_override)
+ reset_control_assert(priv->no_suspend_override);
+
+ return err;
+}
+
+static int ath79_usb_phy_power_off(struct phy *phy)
+{
+ struct ath79_usb_phy *priv = phy_get_drvdata(phy);
+ int err = 0;
+
+ err = reset_control_assert(priv->reset);
+ if (err)
+ return err;
+
+ if (priv->no_suspend_override) {
+ err = reset_control_deassert(priv->no_suspend_override);
+ if (err)
+ reset_control_deassert(priv->reset);
+ }
+
+ return err;
+}
+
+static const struct phy_ops ath79_usb_phy_ops = {
+ .power_on = ath79_usb_phy_power_on,
+ .power_off = ath79_usb_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int ath79_usb_phy_probe(struct platform_device *pdev)
+{
+ struct ath79_usb_phy *priv;
+ struct phy *phy;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->reset = devm_reset_control_get(&pdev->dev, "usb-phy");
+ if (IS_ERR(priv->reset))
+ return PTR_ERR(priv->reset);
+
+ priv->no_suspend_override = devm_reset_control_get_optional(
+ &pdev->dev, "usb-suspend-override");
+ if (IS_ERR(priv->no_suspend_override))
+ return PTR_ERR(priv->no_suspend_override);
+
+ phy = devm_phy_create(&pdev->dev, NULL, &ath79_usb_phy_ops);
+ if (IS_ERR(phy))
+ return PTR_ERR(phy);
+
+ phy_set_drvdata(phy, priv);
+
+ return PTR_ERR_OR_ZERO(devm_of_phy_provider_register(
+ &pdev->dev, of_phy_simple_xlate));
+}
+
+static const struct of_device_id ath79_usb_phy_of_match[] = {
+ { .compatible = "qca,ar7100-usb-phy" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, ath79_usb_phy_of_match);
+
+static struct platform_driver ath79_usb_phy_driver = {
+ .probe = ath79_usb_phy_probe,
+ .driver = {
+ .of_match_table = ath79_usb_phy_of_match,
+ .name = "ath79-usb-phy",
+ }
+};
+module_platform_driver(ath79_usb_phy_driver);
+
+MODULE_DESCRIPTION("ATH79 USB PHY driver");
+MODULE_AUTHOR("Alban Bedel <albeu@free.fr>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c b/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c
new file mode 100644
index 0000000..69ce2af
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c
@@ -0,0 +1,287 @@
+/*
+ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+
+/* PHY registers */
+#define UNIPHY_PLL_REFCLK_CFG 0x000
+#define UNIPHY_PLL_PWRGEN_CFG 0x014
+#define UNIPHY_PLL_GLB_CFG 0x020
+#define UNIPHY_PLL_SDM_CFG0 0x038
+#define UNIPHY_PLL_SDM_CFG1 0x03C
+#define UNIPHY_PLL_SDM_CFG2 0x040
+#define UNIPHY_PLL_SDM_CFG3 0x044
+#define UNIPHY_PLL_SDM_CFG4 0x048
+#define UNIPHY_PLL_SSC_CFG0 0x04C
+#define UNIPHY_PLL_SSC_CFG1 0x050
+#define UNIPHY_PLL_SSC_CFG2 0x054
+#define UNIPHY_PLL_SSC_CFG3 0x058
+#define UNIPHY_PLL_LKDET_CFG0 0x05C
+#define UNIPHY_PLL_LKDET_CFG1 0x060
+#define UNIPHY_PLL_LKDET_CFG2 0x064
+#define UNIPHY_PLL_CAL_CFG0 0x06C
+#define UNIPHY_PLL_CAL_CFG8 0x08C
+#define UNIPHY_PLL_CAL_CFG9 0x090
+#define UNIPHY_PLL_CAL_CFG10 0x094
+#define UNIPHY_PLL_CAL_CFG11 0x098
+#define UNIPHY_PLL_STATUS 0x0C0
+
+#define SATA_PHY_SER_CTRL 0x100
+#define SATA_PHY_TX_DRIV_CTRL0 0x104
+#define SATA_PHY_TX_DRIV_CTRL1 0x108
+#define SATA_PHY_TX_IMCAL0 0x11C
+#define SATA_PHY_TX_IMCAL2 0x124
+#define SATA_PHY_RX_IMCAL0 0x128
+#define SATA_PHY_EQUAL 0x13C
+#define SATA_PHY_OOB_TERM 0x144
+#define SATA_PHY_CDR_CTRL0 0x148
+#define SATA_PHY_CDR_CTRL1 0x14C
+#define SATA_PHY_CDR_CTRL2 0x150
+#define SATA_PHY_CDR_CTRL3 0x154
+#define SATA_PHY_PI_CTRL0 0x168
+#define SATA_PHY_POW_DWN_CTRL0 0x180
+#define SATA_PHY_POW_DWN_CTRL1 0x184
+#define SATA_PHY_TX_DATA_CTRL 0x188
+#define SATA_PHY_ALIGNP 0x1A4
+#define SATA_PHY_TX_IMCAL_STAT 0x1E4
+#define SATA_PHY_RX_IMCAL_STAT 0x1E8
+
+#define UNIPHY_PLL_LOCK BIT(0)
+#define SATA_PHY_TX_CAL BIT(0)
+#define SATA_PHY_RX_CAL BIT(0)
+
+/* default timeout set to 1 sec */
+#define TIMEOUT_MS 10000
+#define DELAY_INTERVAL_US 100
+
+struct qcom_apq8064_sata_phy {
+ void __iomem *mmio;
+ struct clk *cfg_clk;
+ struct device *dev;
+};
+
+/* Helper function to do poll and timeout */
+static int read_poll_timeout(void __iomem *addr, u32 mask)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS);
+
+ do {
+ if (readl_relaxed(addr) & mask)
+ return 0;
+
+ usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
+ } while (!time_after(jiffies, timeout));
+
+ return (readl_relaxed(addr) & mask) ? 0 : -ETIMEDOUT;
+}
+
+static int qcom_apq8064_sata_phy_init(struct phy *generic_phy)
+{
+ struct qcom_apq8064_sata_phy *phy = phy_get_drvdata(generic_phy);
+ void __iomem *base = phy->mmio;
+ int ret = 0;
+
+ /* SATA phy initialization */
+ writel_relaxed(0x01, base + SATA_PHY_SER_CTRL);
+ writel_relaxed(0xB1, base + SATA_PHY_POW_DWN_CTRL0);
+ /* Make sure the power down happens before power up */
+ mb();
+ usleep_range(10, 60);
+
+ writel_relaxed(0x01, base + SATA_PHY_POW_DWN_CTRL0);
+ writel_relaxed(0x3E, base + SATA_PHY_POW_DWN_CTRL1);
+ writel_relaxed(0x01, base + SATA_PHY_RX_IMCAL0);
+ writel_relaxed(0x01, base + SATA_PHY_TX_IMCAL0);
+ writel_relaxed(0x02, base + SATA_PHY_TX_IMCAL2);
+
+ /* Write UNIPHYPLL registers to configure PLL */
+ writel_relaxed(0x04, base + UNIPHY_PLL_REFCLK_CFG);
+ writel_relaxed(0x00, base + UNIPHY_PLL_PWRGEN_CFG);
+
+ writel_relaxed(0x0A, base + UNIPHY_PLL_CAL_CFG0);
+ writel_relaxed(0xF3, base + UNIPHY_PLL_CAL_CFG8);
+ writel_relaxed(0x01, base + UNIPHY_PLL_CAL_CFG9);
+ writel_relaxed(0xED, base + UNIPHY_PLL_CAL_CFG10);
+ writel_relaxed(0x02, base + UNIPHY_PLL_CAL_CFG11);
+
+ writel_relaxed(0x36, base + UNIPHY_PLL_SDM_CFG0);
+ writel_relaxed(0x0D, base + UNIPHY_PLL_SDM_CFG1);
+ writel_relaxed(0xA3, base + UNIPHY_PLL_SDM_CFG2);
+ writel_relaxed(0xF0, base + UNIPHY_PLL_SDM_CFG3);
+ writel_relaxed(0x00, base + UNIPHY_PLL_SDM_CFG4);
+
+ writel_relaxed(0x19, base + UNIPHY_PLL_SSC_CFG0);
+ writel_relaxed(0xE1, base + UNIPHY_PLL_SSC_CFG1);
+ writel_relaxed(0x00, base + UNIPHY_PLL_SSC_CFG2);
+ writel_relaxed(0x11, base + UNIPHY_PLL_SSC_CFG3);
+
+ writel_relaxed(0x04, base + UNIPHY_PLL_LKDET_CFG0);
+ writel_relaxed(0xFF, base + UNIPHY_PLL_LKDET_CFG1);
+
+ writel_relaxed(0x02, base + UNIPHY_PLL_GLB_CFG);
+ /* make sure global config LDO power down happens before power up */
+ mb();
+
+ writel_relaxed(0x03, base + UNIPHY_PLL_GLB_CFG);
+ writel_relaxed(0x05, base + UNIPHY_PLL_LKDET_CFG2);
+
+ /* PLL Lock wait */
+ ret = read_poll_timeout(base + UNIPHY_PLL_STATUS, UNIPHY_PLL_LOCK);
+ if (ret) {
+ dev_err(phy->dev, "poll timeout UNIPHY_PLL_STATUS\n");
+ return ret;
+ }
+
+ /* TX Calibration */
+ ret = read_poll_timeout(base + SATA_PHY_TX_IMCAL_STAT, SATA_PHY_TX_CAL);
+ if (ret) {
+ dev_err(phy->dev, "poll timeout SATA_PHY_TX_IMCAL_STAT\n");
+ return ret;
+ }
+
+ /* RX Calibration */
+ ret = read_poll_timeout(base + SATA_PHY_RX_IMCAL_STAT, SATA_PHY_RX_CAL);
+ if (ret) {
+ dev_err(phy->dev, "poll timeout SATA_PHY_RX_IMCAL_STAT\n");
+ return ret;
+ }
+
+ /* SATA phy calibrated succesfully, power up to functional mode */
+ writel_relaxed(0x3E, base + SATA_PHY_POW_DWN_CTRL1);
+ writel_relaxed(0x01, base + SATA_PHY_RX_IMCAL0);
+ writel_relaxed(0x01, base + SATA_PHY_TX_IMCAL0);
+
+ writel_relaxed(0x00, base + SATA_PHY_POW_DWN_CTRL1);
+ writel_relaxed(0x59, base + SATA_PHY_CDR_CTRL0);
+ writel_relaxed(0x04, base + SATA_PHY_CDR_CTRL1);
+ writel_relaxed(0x00, base + SATA_PHY_CDR_CTRL2);
+ writel_relaxed(0x00, base + SATA_PHY_PI_CTRL0);
+ writel_relaxed(0x00, base + SATA_PHY_CDR_CTRL3);
+ writel_relaxed(0x01, base + SATA_PHY_POW_DWN_CTRL0);
+
+ writel_relaxed(0x11, base + SATA_PHY_TX_DATA_CTRL);
+ writel_relaxed(0x43, base + SATA_PHY_ALIGNP);
+ writel_relaxed(0x04, base + SATA_PHY_OOB_TERM);
+
+ writel_relaxed(0x01, base + SATA_PHY_EQUAL);
+ writel_relaxed(0x09, base + SATA_PHY_TX_DRIV_CTRL0);
+ writel_relaxed(0x09, base + SATA_PHY_TX_DRIV_CTRL1);
+
+ return 0;
+}
+
+static int qcom_apq8064_sata_phy_exit(struct phy *generic_phy)
+{
+ struct qcom_apq8064_sata_phy *phy = phy_get_drvdata(generic_phy);
+ void __iomem *base = phy->mmio;
+
+ /* Power down PHY */
+ writel_relaxed(0xF8, base + SATA_PHY_POW_DWN_CTRL0);
+ writel_relaxed(0xFE, base + SATA_PHY_POW_DWN_CTRL1);
+
+ /* Power down PLL block */
+ writel_relaxed(0x00, base + UNIPHY_PLL_GLB_CFG);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_apq8064_sata_phy_ops = {
+ .init = qcom_apq8064_sata_phy_init,
+ .exit = qcom_apq8064_sata_phy_exit,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_apq8064_sata_phy_probe(struct platform_device *pdev)
+{
+ struct qcom_apq8064_sata_phy *phy;
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct phy_provider *phy_provider;
+ struct phy *generic_phy;
+ int ret;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ phy->mmio = devm_ioremap_resource(dev, res);
+ if (IS_ERR(phy->mmio))
+ return PTR_ERR(phy->mmio);
+
+ generic_phy = devm_phy_create(dev, NULL, &qcom_apq8064_sata_phy_ops);
+ if (IS_ERR(generic_phy)) {
+ dev_err(dev, "%s: failed to create phy\n", __func__);
+ return PTR_ERR(generic_phy);
+ }
+
+ phy->dev = dev;
+ phy_set_drvdata(generic_phy, phy);
+ platform_set_drvdata(pdev, phy);
+
+ phy->cfg_clk = devm_clk_get(dev, "cfg");
+ if (IS_ERR(phy->cfg_clk)) {
+ dev_err(dev, "Failed to get sata cfg clock\n");
+ return PTR_ERR(phy->cfg_clk);
+ }
+
+ ret = clk_prepare_enable(phy->cfg_clk);
+ if (ret)
+ return ret;
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider)) {
+ clk_disable_unprepare(phy->cfg_clk);
+ dev_err(dev, "%s: failed to register phy\n", __func__);
+ return PTR_ERR(phy_provider);
+ }
+
+ return 0;
+}
+
+static int qcom_apq8064_sata_phy_remove(struct platform_device *pdev)
+{
+ struct qcom_apq8064_sata_phy *phy = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(phy->cfg_clk);
+
+ return 0;
+}
+
+static const struct of_device_id qcom_apq8064_sata_phy_of_match[] = {
+ { .compatible = "qcom,apq8064-sata-phy" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_apq8064_sata_phy_of_match);
+
+static struct platform_driver qcom_apq8064_sata_phy_driver = {
+ .probe = qcom_apq8064_sata_phy_probe,
+ .remove = qcom_apq8064_sata_phy_remove,
+ .driver = {
+ .name = "qcom-apq8064-sata-phy",
+ .of_match_table = qcom_apq8064_sata_phy_of_match,
+ }
+};
+module_platform_driver(qcom_apq8064_sata_phy_driver);
+
+MODULE_DESCRIPTION("QCOM apq8064 SATA PHY driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c b/drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c
new file mode 100644
index 0000000..0ad127c
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c
@@ -0,0 +1,209 @@
+/*
+ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+
+struct qcom_ipq806x_sata_phy {
+ void __iomem *mmio;
+ struct clk *cfg_clk;
+ struct device *dev;
+};
+
+#define __set(v, a, b) (((v) << (b)) & GENMASK(a, b))
+
+#define SATA_PHY_P0_PARAM0 0x200
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3(x) __set(x, 17, 12)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3_MASK GENMASK(17, 12)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2(x) __set(x, 11, 6)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2_MASK GENMASK(11, 6)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1(x) __set(x, 5, 0)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1_MASK GENMASK(5, 0)
+
+#define SATA_PHY_P0_PARAM1 0x204
+#define SATA_PHY_P0_PARAM1_RESERVED_BITS31_21(x) __set(x, 31, 21)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3(x) __set(x, 20, 14)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3_MASK GENMASK(20, 14)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2(x) __set(x, 13, 7)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2_MASK GENMASK(13, 7)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1(x) __set(x, 6, 0)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1_MASK GENMASK(6, 0)
+
+#define SATA_PHY_P0_PARAM2 0x208
+#define SATA_PHY_P0_PARAM2_RX_EQ(x) __set(x, 20, 18)
+#define SATA_PHY_P0_PARAM2_RX_EQ_MASK GENMASK(20, 18)
+
+#define SATA_PHY_P0_PARAM3 0x20C
+#define SATA_PHY_SSC_EN 0x8
+#define SATA_PHY_P0_PARAM4 0x210
+#define SATA_PHY_REF_SSP_EN 0x2
+#define SATA_PHY_RESET 0x1
+
+static int qcom_ipq806x_sata_phy_init(struct phy *generic_phy)
+{
+ struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
+ u32 reg;
+
+ /* Setting SSC_EN to 1 */
+ reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM3);
+ reg = reg | SATA_PHY_SSC_EN;
+ writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM3);
+
+ reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM0) &
+ ~(SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3_MASK |
+ SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2_MASK |
+ SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1_MASK);
+ reg |= SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3(0xf);
+ writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM0);
+
+ reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM1) &
+ ~(SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3_MASK |
+ SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2_MASK |
+ SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1_MASK);
+ reg |= SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3(0x55) |
+ SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2(0x55) |
+ SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1(0x55);
+ writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM1);
+
+ reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM2) &
+ ~SATA_PHY_P0_PARAM2_RX_EQ_MASK;
+ reg |= SATA_PHY_P0_PARAM2_RX_EQ(0x3);
+ writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM2);
+
+ /* Setting PHY_RESET to 1 */
+ reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
+ reg = reg | SATA_PHY_RESET;
+ writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
+
+ /* Setting REF_SSP_EN to 1 */
+ reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
+ reg = reg | SATA_PHY_REF_SSP_EN | SATA_PHY_RESET;
+ writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
+
+ /* make sure all changes complete before we let the PHY out of reset */
+ mb();
+
+ /* sleep for max. 50us more to combine processor wakeups */
+ usleep_range(20, 20 + 50);
+
+ /* Clearing PHY_RESET to 0 */
+ reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
+ reg = reg & ~SATA_PHY_RESET;
+ writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
+
+ return 0;
+}
+
+static int qcom_ipq806x_sata_phy_exit(struct phy *generic_phy)
+{
+ struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
+ u32 reg;
+
+ /* Setting PHY_RESET to 1 */
+ reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
+ reg = reg | SATA_PHY_RESET;
+ writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_ipq806x_sata_phy_ops = {
+ .init = qcom_ipq806x_sata_phy_init,
+ .exit = qcom_ipq806x_sata_phy_exit,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_ipq806x_sata_phy_probe(struct platform_device *pdev)
+{
+ struct qcom_ipq806x_sata_phy *phy;
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct phy_provider *phy_provider;
+ struct phy *generic_phy;
+ int ret;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ phy->mmio = devm_ioremap_resource(dev, res);
+ if (IS_ERR(phy->mmio))
+ return PTR_ERR(phy->mmio);
+
+ generic_phy = devm_phy_create(dev, NULL, &qcom_ipq806x_sata_phy_ops);
+ if (IS_ERR(generic_phy)) {
+ dev_err(dev, "%s: failed to create phy\n", __func__);
+ return PTR_ERR(generic_phy);
+ }
+
+ phy->dev = dev;
+ phy_set_drvdata(generic_phy, phy);
+ platform_set_drvdata(pdev, phy);
+
+ phy->cfg_clk = devm_clk_get(dev, "cfg");
+ if (IS_ERR(phy->cfg_clk)) {
+ dev_err(dev, "Failed to get sata cfg clock\n");
+ return PTR_ERR(phy->cfg_clk);
+ }
+
+ ret = clk_prepare_enable(phy->cfg_clk);
+ if (ret)
+ return ret;
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider)) {
+ clk_disable_unprepare(phy->cfg_clk);
+ dev_err(dev, "%s: failed to register phy\n", __func__);
+ return PTR_ERR(phy_provider);
+ }
+
+ return 0;
+}
+
+static int qcom_ipq806x_sata_phy_remove(struct platform_device *pdev)
+{
+ struct qcom_ipq806x_sata_phy *phy = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(phy->cfg_clk);
+
+ return 0;
+}
+
+static const struct of_device_id qcom_ipq806x_sata_phy_of_match[] = {
+ { .compatible = "qcom,ipq806x-sata-phy" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_ipq806x_sata_phy_of_match);
+
+static struct platform_driver qcom_ipq806x_sata_phy_driver = {
+ .probe = qcom_ipq806x_sata_phy_probe,
+ .remove = qcom_ipq806x_sata_phy_remove,
+ .driver = {
+ .name = "qcom-ipq806x-sata-phy",
+ .of_match_table = qcom_ipq806x_sata_phy_of_match,
+ }
+};
+module_platform_driver(qcom_ipq806x_sata_phy_driver);
+
+MODULE_DESCRIPTION("QCOM IPQ806x SATA PHY driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
new file mode 100644
index 0000000..4c47010
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -0,0 +1,1657 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#include <dt-bindings/phy/phy.h>
+
+#include "phy-qcom-qmp.h"
+
+/* QPHY_SW_RESET bit */
+#define SW_RESET BIT(0)
+/* QPHY_POWER_DOWN_CONTROL */
+#define SW_PWRDN BIT(0)
+#define REFCLK_DRV_DSBL BIT(1)
+/* QPHY_START_CONTROL bits */
+#define SERDES_START BIT(0)
+#define PCS_START BIT(1)
+#define PLL_READY_GATE_EN BIT(3)
+/* QPHY_PCS_STATUS bit */
+#define PHYSTATUS BIT(6)
+/* QPHY_COM_PCS_READY_STATUS bit */
+#define PCS_READY BIT(0)
+
+/* QPHY_V3_DP_COM_RESET_OVRD_CTRL register bits */
+/* DP PHY soft reset */
+#define SW_DPPHY_RESET BIT(0)
+/* mux to select DP PHY reset control, 0:HW control, 1: software reset */
+#define SW_DPPHY_RESET_MUX BIT(1)
+/* USB3 PHY soft reset */
+#define SW_USB3PHY_RESET BIT(2)
+/* mux to select USB3 PHY reset control, 0:HW control, 1: software reset */
+#define SW_USB3PHY_RESET_MUX BIT(3)
+
+/* QPHY_V3_DP_COM_PHY_MODE_CTRL register bits */
+#define USB3_MODE BIT(0) /* enables USB3 mode */
+#define DP_MODE BIT(1) /* enables DP mode */
+
+/* QPHY_PCS_AUTONOMOUS_MODE_CTRL register bits */
+#define ARCVR_DTCT_EN BIT(0)
+#define ALFPS_DTCT_EN BIT(1)
+#define ARCVR_DTCT_EVENT_SEL BIT(4)
+
+/* QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR register bits */
+#define IRQ_CLEAR BIT(0)
+
+/* QPHY_PCS_LFPS_RXTERM_IRQ_STATUS register bits */
+#define RCVR_DETECT BIT(0)
+
+/* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
+#define CLAMP_EN BIT(0) /* enables i/o clamp_n */
+
+#define PHY_INIT_COMPLETE_TIMEOUT 1000
+#define POWER_DOWN_DELAY_US_MIN 10
+#define POWER_DOWN_DELAY_US_MAX 11
+
+#define MAX_PROP_NAME 32
+
+struct qmp_phy_init_tbl {
+ unsigned int offset;
+ unsigned int val;
+ /*
+ * register part of layout ?
+ * if yes, then offset gives index in the reg-layout
+ */
+ int in_layout;
+};
+
+#define QMP_PHY_INIT_CFG(o, v) \
+ { \
+ .offset = o, \
+ .val = v, \
+ }
+
+#define QMP_PHY_INIT_CFG_L(o, v) \
+ { \
+ .offset = o, \
+ .val = v, \
+ .in_layout = 1, \
+ }
+
+/* set of registers with offsets different per-PHY */
+enum qphy_reg_layout {
+ /* Common block control registers */
+ QPHY_COM_SW_RESET,
+ QPHY_COM_POWER_DOWN_CONTROL,
+ QPHY_COM_START_CONTROL,
+ QPHY_COM_PCS_READY_STATUS,
+ /* PCS registers */
+ QPHY_PLL_LOCK_CHK_DLY_TIME,
+ QPHY_FLL_CNTRL1,
+ QPHY_FLL_CNTRL2,
+ QPHY_FLL_CNT_VAL_L,
+ QPHY_FLL_CNT_VAL_H_TOL,
+ QPHY_FLL_MAN_CODE,
+ QPHY_SW_RESET,
+ QPHY_START_CTRL,
+ QPHY_PCS_READY_STATUS,
+ QPHY_PCS_AUTONOMOUS_MODE_CTRL,
+ QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR,
+ QPHY_PCS_LFPS_RXTERM_IRQ_STATUS,
+};
+
+static const unsigned int pciephy_regs_layout[] = {
+ [QPHY_COM_SW_RESET] = 0x400,
+ [QPHY_COM_POWER_DOWN_CONTROL] = 0x404,
+ [QPHY_COM_START_CONTROL] = 0x408,
+ [QPHY_COM_PCS_READY_STATUS] = 0x448,
+ [QPHY_PLL_LOCK_CHK_DLY_TIME] = 0xa8,
+ [QPHY_FLL_CNTRL1] = 0xc4,
+ [QPHY_FLL_CNTRL2] = 0xc8,
+ [QPHY_FLL_CNT_VAL_L] = 0xcc,
+ [QPHY_FLL_CNT_VAL_H_TOL] = 0xd0,
+ [QPHY_FLL_MAN_CODE] = 0xd4,
+ [QPHY_SW_RESET] = 0x00,
+ [QPHY_START_CTRL] = 0x08,
+ [QPHY_PCS_READY_STATUS] = 0x174,
+};
+
+static const unsigned int usb3phy_regs_layout[] = {
+ [QPHY_FLL_CNTRL1] = 0xc0,
+ [QPHY_FLL_CNTRL2] = 0xc4,
+ [QPHY_FLL_CNT_VAL_L] = 0xc8,
+ [QPHY_FLL_CNT_VAL_H_TOL] = 0xcc,
+ [QPHY_FLL_MAN_CODE] = 0xd0,
+ [QPHY_SW_RESET] = 0x00,
+ [QPHY_START_CTRL] = 0x08,
+ [QPHY_PCS_READY_STATUS] = 0x17c,
+ [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d4,
+ [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0d8,
+ [QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x178,
+};
+
+static const unsigned int qmp_v3_usb3phy_regs_layout[] = {
+ [QPHY_SW_RESET] = 0x00,
+ [QPHY_START_CTRL] = 0x08,
+ [QPHY_PCS_READY_STATUS] = 0x174,
+ [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d8,
+ [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0dc,
+ [QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x170,
+};
+
+static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x42),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x09),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x1a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_BUF_ENABLE, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x2f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x19),
+ QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x15),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_EP_DIV, 0x19),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x40),
+};
+
+static const struct qmp_phy_init_tbl msm8996_pcie_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
+ QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06),
+};
+
+static const struct qmp_phy_init_tbl msm8996_pcie_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_ENABLES, 0x1c),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xdb),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_BAND, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN_HALF, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x19),
+};
+
+static const struct qmp_phy_init_tbl msm8996_pcie_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_RX_IDLE_DTCT_CNTRL, 0x4c),
+ QMP_PHY_INIT_CFG(QPHY_PWRUP_RESET_DLY_TIME_AUXCLK, 0x00),
+ QMP_PHY_INIT_CFG(QPHY_LP_WAKEUP_DLY_TIME_AUXCLK, 0x01),
+
+ QMP_PHY_INIT_CFG_L(QPHY_PLL_LOCK_CHK_DLY_TIME, 0x05),
+
+ QMP_PHY_INIT_CFG(QPHY_ENDPOINT_REFCLK_DRIVE, 0x05),
+ QMP_PHY_INIT_CFG(QPHY_POWER_DOWN_CONTROL, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG4, 0x00),
+ QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG1, 0xa3),
+ QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0x0e),
+};
+
+static const struct qmp_phy_init_tbl msm8996_usb3_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x30),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x04),
+ /* PLL and Loop filter settings */
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x15),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x34),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_CFG, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x0a),
+ /* SSC settings */
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0xde),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl msm8996_usb3_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
+ QMP_PHY_INIT_CFG(QSERDES_TX_RCV_DETECT_LVL_2, 0x12),
+ QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06),
+};
+
+static const struct qmp_phy_init_tbl msm8996_usb3_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4c),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xbb),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x16),
+};
+
+static const struct qmp_phy_init_tbl msm8996_usb3_pcs_tbl[] = {
+ /* FLL settings */
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL2, 0x03),
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL1, 0x02),
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_L, 0x09),
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_H_TOL, 0x42),
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_MAN_CODE, 0x85),
+
+ /* Lock Det settings */
+ QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG1, 0xd1),
+ QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG2, 0x1f),
+ QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG3, 0x47),
+ QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG2, 0x08),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0xf),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x6),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0xf),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x20),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0xa),
+ QMP_PHY_INIT_CFG(QSERDES_COM_RESETSM_CNTRL, 0x20),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0xa),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0xa),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x3),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0xD),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0xD04),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x2),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_BUF_ENABLE, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0xb),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CTRL_BY_PSM, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0xa),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x2),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x2f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x19),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_EP_DIV, 0x19),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x7),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
+ QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x6),
+ QMP_PHY_INIT_CFG(QSERDES_TX_RES_CODE_LANE_OFFSET, 0x2),
+ QMP_PHY_INIT_CFG(QSERDES_TX_RCV_DETECT_LVL_2, 0x12),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_ENABLES, 0x1c),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xdb),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x4),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN_HALF, 0x4),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_ENDPOINT_REFCLK_DRIVE, 0x4),
+ QMP_PHY_INIT_CFG(QPHY_OSC_DTCT_ACTIONS, 0x0),
+ QMP_PHY_INIT_CFG(QPHY_PWRUP_RESET_DLY_TIME_AUXCLK, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB, 0x0),
+ QMP_PHY_INIT_CFG(QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_PLL_LOCK_CHK_DLY_TIME_AUXCLK_LSB, 0x0),
+ QMP_PHY_INIT_CFG(QPHY_LP_WAKEUP_DLY_TIME_AUXCLK, 0x40),
+ QMP_PHY_INIT_CFG_L(QPHY_PLL_LOCK_CHK_DLY_TIME, 0x73),
+ QMP_PHY_INIT_CFG(QPHY_RX_SIGDET_LVL, 0x99),
+ QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M6DB_V0, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0xe),
+ QMP_PHY_INIT_CFG_L(QPHY_SW_RESET, 0x0),
+ QMP_PHY_INIT_CFG_L(QPHY_START_CTRL, 0x3),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL2, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0xab),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0xea),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x34),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x15),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_CFG, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x31),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x85),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x09),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x06),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_pcs_tbl[] = {
+ /* FLL settings */
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02),
+
+ /* Lock Det settings */
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b),
+
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0xba),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb7),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4e),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x65),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6b),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V1, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x1d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d),
+
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL2, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0xab),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0xea),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x34),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x15),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_CFG, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x31),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x85),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0xc6),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x06),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_VGA_CAL_CNTRL2, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x50),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0e),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x1c),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_pcs_tbl[] = {
+ /* FLL settings */
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02),
+
+ /* Lock Det settings */
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b),
+
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0xba),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb5),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4c),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x64),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6a),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V1, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x1d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d),
+
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
+
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG1, 0x21),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG2, 0x60),
+};
+
+
+/* struct qmp_phy_cfg - per-PHY initialization config */
+struct qmp_phy_cfg {
+ /* phy-type - PCIE/UFS/USB */
+ unsigned int type;
+ /* number of lanes provided by phy */
+ int nlanes;
+
+ /* Init sequence for PHY blocks - serdes, tx, rx, pcs */
+ const struct qmp_phy_init_tbl *serdes_tbl;
+ int serdes_tbl_num;
+ const struct qmp_phy_init_tbl *tx_tbl;
+ int tx_tbl_num;
+ const struct qmp_phy_init_tbl *rx_tbl;
+ int rx_tbl_num;
+ const struct qmp_phy_init_tbl *pcs_tbl;
+ int pcs_tbl_num;
+
+ /* clock ids to be requested */
+ const char * const *clk_list;
+ int num_clks;
+ /* resets to be requested */
+ const char * const *reset_list;
+ int num_resets;
+ /* regulators to be requested */
+ const char * const *vreg_list;
+ int num_vregs;
+
+ /* array of registers with different offsets */
+ const unsigned int *regs;
+
+ unsigned int start_ctrl;
+ unsigned int pwrdn_ctrl;
+ unsigned int mask_pcs_ready;
+ unsigned int mask_com_pcs_ready;
+
+ /* true, if PHY has a separate PHY_COM control block */
+ bool has_phy_com_ctrl;
+ /* true, if PHY has a reset for individual lanes */
+ bool has_lane_rst;
+ /* true, if PHY needs delay after POWER_DOWN */
+ bool has_pwrdn_delay;
+ /* power_down delay in usec */
+ int pwrdn_delay_min;
+ int pwrdn_delay_max;
+
+ /* true, if PHY has a separate DP_COM control block */
+ bool has_phy_dp_com_ctrl;
+ /* Register offset of secondary tx/rx lanes for USB DP combo PHY */
+ unsigned int tx_b_lane_offset;
+ unsigned int rx_b_lane_offset;
+};
+
+/**
+ * struct qmp_phy - per-lane phy descriptor
+ *
+ * @phy: generic phy
+ * @tx: iomapped memory space for lane's tx
+ * @rx: iomapped memory space for lane's rx
+ * @pcs: iomapped memory space for lane's pcs
+ * @pcs_misc: iomapped memory space for lane's pcs_misc
+ * @pipe_clk: pipe lock
+ * @index: lane index
+ * @qmp: QMP phy to which this lane belongs
+ * @lane_rst: lane's reset controller
+ */
+struct qmp_phy {
+ struct phy *phy;
+ void __iomem *tx;
+ void __iomem *rx;
+ void __iomem *pcs;
+ void __iomem *pcs_misc;
+ struct clk *pipe_clk;
+ unsigned int index;
+ struct qcom_qmp *qmp;
+ struct reset_control *lane_rst;
+};
+
+/**
+ * struct qcom_qmp - structure holding QMP phy block attributes
+ *
+ * @dev: device
+ * @serdes: iomapped memory space for phy's serdes
+ * @dp_com: iomapped memory space for phy's dp_com control block
+ *
+ * @clks: array of clocks required by phy
+ * @resets: array of resets required by phy
+ * @vregs: regulator supplies bulk data
+ *
+ * @cfg: phy specific configuration
+ * @phys: array of per-lane phy descriptors
+ * @phy_mutex: mutex lock for PHY common block initialization
+ * @init_count: phy common block initialization count
+ * @phy_initialized: indicate if PHY has been initialized
+ * @mode: current PHY mode
+ */
+struct qcom_qmp {
+ struct device *dev;
+ void __iomem *serdes;
+ void __iomem *dp_com;
+
+ struct clk_bulk_data *clks;
+ struct reset_control **resets;
+ struct regulator_bulk_data *vregs;
+
+ const struct qmp_phy_cfg *cfg;
+ struct qmp_phy **phys;
+
+ struct mutex phy_mutex;
+ int init_count;
+ bool phy_initialized;
+ enum phy_mode mode;
+};
+
+static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val)
+{
+ u32 reg;
+
+ reg = readl(base + offset);
+ reg |= val;
+ writel(reg, base + offset);
+
+ /* ensure that above write is through */
+ readl(base + offset);
+}
+
+static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
+{
+ u32 reg;
+
+ reg = readl(base + offset);
+ reg &= ~val;
+ writel(reg, base + offset);
+
+ /* ensure that above write is through */
+ readl(base + offset);
+}
+
+/* list of clocks required by phy */
+static const char * const msm8996_phy_clk_l[] = {
+ "aux", "cfg_ahb", "ref",
+};
+
+static const char * const qmp_v3_phy_clk_l[] = {
+ "aux", "cfg_ahb", "ref", "com_aux",
+};
+
+/* list of resets */
+static const char * const msm8996_pciephy_reset_l[] = {
+ "phy", "common", "cfg",
+};
+
+static const char * const msm8996_usb3phy_reset_l[] = {
+ "phy", "common",
+};
+
+/* list of regulators */
+static const char * const msm8996_phy_vreg_l[] = {
+ "vdda-phy", "vdda-pll",
+};
+
+static const struct qmp_phy_cfg msm8996_pciephy_cfg = {
+ .type = PHY_TYPE_PCIE,
+ .nlanes = 3,
+
+ .serdes_tbl = msm8996_pcie_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(msm8996_pcie_serdes_tbl),
+ .tx_tbl = msm8996_pcie_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(msm8996_pcie_tx_tbl),
+ .rx_tbl = msm8996_pcie_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(msm8996_pcie_rx_tbl),
+ .pcs_tbl = msm8996_pcie_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(msm8996_pcie_pcs_tbl),
+ .clk_list = msm8996_phy_clk_l,
+ .num_clks = ARRAY_SIZE(msm8996_phy_clk_l),
+ .reset_list = msm8996_pciephy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_pciephy_reset_l),
+ .vreg_list = msm8996_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .regs = pciephy_regs_layout,
+
+ .start_ctrl = PCS_START | PLL_READY_GATE_EN,
+ .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL,
+ .mask_com_pcs_ready = PCS_READY,
+
+ .has_phy_com_ctrl = true,
+ .has_lane_rst = true,
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+};
+
+static const struct qmp_phy_cfg msm8996_usb3phy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = msm8996_usb3_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(msm8996_usb3_serdes_tbl),
+ .tx_tbl = msm8996_usb3_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(msm8996_usb3_tx_tbl),
+ .rx_tbl = msm8996_usb3_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(msm8996_usb3_rx_tbl),
+ .pcs_tbl = msm8996_usb3_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(msm8996_usb3_pcs_tbl),
+ .clk_list = msm8996_phy_clk_l,
+ .num_clks = ARRAY_SIZE(msm8996_phy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = msm8996_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .regs = usb3phy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+ .mask_pcs_ready = PHYSTATUS,
+};
+
+/* list of resets */
+static const char * const ipq8074_pciephy_reset_l[] = {
+ "phy", "common",
+};
+
+static const struct qmp_phy_cfg ipq8074_pciephy_cfg = {
+ .type = PHY_TYPE_PCIE,
+ .nlanes = 1,
+
+ .serdes_tbl = ipq8074_pcie_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(ipq8074_pcie_serdes_tbl),
+ .tx_tbl = ipq8074_pcie_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(ipq8074_pcie_tx_tbl),
+ .rx_tbl = ipq8074_pcie_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(ipq8074_pcie_rx_tbl),
+ .pcs_tbl = ipq8074_pcie_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(ipq8074_pcie_pcs_tbl),
+ .clk_list = NULL,
+ .num_clks = 0,
+ .reset_list = ipq8074_pciephy_reset_l,
+ .num_resets = ARRAY_SIZE(ipq8074_pciephy_reset_l),
+ .vreg_list = NULL,
+ .num_vregs = 0,
+ .regs = pciephy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL,
+ .mask_pcs_ready = PHYSTATUS,
+
+ .has_phy_com_ctrl = false,
+ .has_lane_rst = false,
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = 995, /* us */
+ .pwrdn_delay_max = 1005, /* us */
+};
+
+static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = qmp_v3_usb3_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
+ .tx_tbl = qmp_v3_usb3_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_tx_tbl),
+ .rx_tbl = qmp_v3_usb3_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_rx_tbl),
+ .pcs_tbl = qmp_v3_usb3_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(qmp_v3_usb3_pcs_tbl),
+ .clk_list = qmp_v3_phy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v3_phy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = msm8996_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .regs = qmp_v3_usb3phy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+ .mask_pcs_ready = PHYSTATUS,
+
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+
+ .has_phy_dp_com_ctrl = true,
+ .tx_b_lane_offset = 0x400,
+ .rx_b_lane_offset = 0x400,
+};
+
+static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = qmp_v3_usb3_uniphy_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(qmp_v3_usb3_uniphy_serdes_tbl),
+ .tx_tbl = qmp_v3_usb3_uniphy_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_uniphy_tx_tbl),
+ .rx_tbl = qmp_v3_usb3_uniphy_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_uniphy_rx_tbl),
+ .pcs_tbl = qmp_v3_usb3_uniphy_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(qmp_v3_usb3_uniphy_pcs_tbl),
+ .clk_list = qmp_v3_phy_clk_l,
+ .num_clks = ARRAY_SIZE(qmp_v3_phy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = msm8996_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .regs = qmp_v3_usb3phy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+ .mask_pcs_ready = PHYSTATUS,
+
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+};
+
+static void qcom_qmp_phy_configure(void __iomem *base,
+ const unsigned int *regs,
+ const struct qmp_phy_init_tbl tbl[],
+ int num)
+{
+ int i;
+ const struct qmp_phy_init_tbl *t = tbl;
+
+ if (!t)
+ return;
+
+ for (i = 0; i < num; i++, t++) {
+ if (t->in_layout)
+ writel(t->val, base + regs[t->offset]);
+ else
+ writel(t->val, base + t->offset);
+ }
+}
+
+static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
+{
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *serdes = qmp->serdes;
+ void __iomem *dp_com = qmp->dp_com;
+ int ret, i;
+
+ mutex_lock(&qmp->phy_mutex);
+ if (qmp->init_count++) {
+ mutex_unlock(&qmp->phy_mutex);
+ return 0;
+ }
+
+ /* turn on regulator supplies */
+ ret = regulator_bulk_enable(cfg->num_vregs, qmp->vregs);
+ if (ret) {
+ dev_err(qmp->dev, "failed to enable regulators, err=%d\n", ret);
+ goto err_reg_enable;
+ }
+
+ for (i = 0; i < cfg->num_resets; i++) {
+ ret = reset_control_assert(qmp->resets[i]);
+ if (ret) {
+ dev_err(qmp->dev, "%s reset assert failed\n",
+ cfg->reset_list[i]);
+ goto err_rst_assert;
+ }
+ }
+
+ for (i = cfg->num_resets - 1; i >= 0; i--) {
+ ret = reset_control_deassert(qmp->resets[i]);
+ if (ret) {
+ dev_err(qmp->dev, "%s reset deassert failed\n",
+ qmp->cfg->reset_list[i]);
+ goto err_rst;
+ }
+ }
+
+ ret = clk_bulk_prepare_enable(cfg->num_clks, qmp->clks);
+ if (ret) {
+ dev_err(qmp->dev, "failed to enable clks, err=%d\n", ret);
+ goto err_rst;
+ }
+
+ if (cfg->has_phy_com_ctrl)
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
+ SW_PWRDN);
+
+ if (cfg->has_phy_dp_com_ctrl) {
+ qphy_setbits(dp_com, QPHY_V3_DP_COM_POWER_DOWN_CTRL,
+ SW_PWRDN);
+ /* override hardware control for reset of qmp phy */
+ qphy_setbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
+ SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
+ SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+
+ qphy_setbits(dp_com, QPHY_V3_DP_COM_PHY_MODE_CTRL,
+ USB3_MODE | DP_MODE);
+
+ /* bring both QMP USB and QMP DP PHYs PCS block out of reset */
+ qphy_clrbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
+ SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
+ SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+ }
+
+ /* Serdes configuration */
+ qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
+ cfg->serdes_tbl_num);
+
+ if (cfg->has_phy_com_ctrl) {
+ void __iomem *status;
+ unsigned int mask, val;
+
+ qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], SW_RESET);
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
+ SERDES_START | PCS_START);
+
+ status = serdes + cfg->regs[QPHY_COM_PCS_READY_STATUS];
+ mask = cfg->mask_com_pcs_ready;
+
+ ret = readl_poll_timeout(status, val, (val & mask), 10,
+ PHY_INIT_COMPLETE_TIMEOUT);
+ if (ret) {
+ dev_err(qmp->dev,
+ "phy common block init timed-out\n");
+ goto err_com_init;
+ }
+ }
+
+ mutex_unlock(&qmp->phy_mutex);
+
+ return 0;
+
+err_com_init:
+ clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
+err_rst:
+ while (++i < cfg->num_resets)
+ reset_control_assert(qmp->resets[i]);
+err_rst_assert:
+ regulator_bulk_disable(cfg->num_vregs, qmp->vregs);
+err_reg_enable:
+ mutex_unlock(&qmp->phy_mutex);
+
+ return ret;
+}
+
+static int qcom_qmp_phy_com_exit(struct qcom_qmp *qmp)
+{
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *serdes = qmp->serdes;
+ int i = cfg->num_resets;
+
+ mutex_lock(&qmp->phy_mutex);
+ if (--qmp->init_count) {
+ mutex_unlock(&qmp->phy_mutex);
+ return 0;
+ }
+
+ if (cfg->has_phy_com_ctrl) {
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
+ SERDES_START | PCS_START);
+ qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET],
+ SW_RESET);
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
+ SW_PWRDN);
+ }
+
+ while (--i >= 0)
+ reset_control_assert(qmp->resets[i]);
+
+ clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
+
+ regulator_bulk_disable(cfg->num_vregs, qmp->vregs);
+
+ mutex_unlock(&qmp->phy_mutex);
+
+ return 0;
+}
+
+/* PHY Initialization */
+static int qcom_qmp_phy_init(struct phy *phy)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *tx = qphy->tx;
+ void __iomem *rx = qphy->rx;
+ void __iomem *pcs = qphy->pcs;
+ void __iomem *dp_com = qmp->dp_com;
+ void __iomem *status;
+ unsigned int mask, val;
+ int ret;
+
+ dev_vdbg(qmp->dev, "Initializing QMP phy\n");
+
+ ret = qcom_qmp_phy_com_init(qmp);
+ if (ret)
+ return ret;
+
+ if (cfg->has_lane_rst) {
+ ret = reset_control_deassert(qphy->lane_rst);
+ if (ret) {
+ dev_err(qmp->dev, "lane%d reset deassert failed\n",
+ qphy->index);
+ goto err_lane_rst;
+ }
+ }
+
+ ret = clk_prepare_enable(qphy->pipe_clk);
+ if (ret) {
+ dev_err(qmp->dev, "pipe_clk enable failed err=%d\n", ret);
+ goto err_clk_enable;
+ }
+
+ /* Tx, Rx, and PCS configurations */
+ qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
+ /* Configuration for other LANE for USB-DP combo PHY */
+ if (cfg->has_phy_dp_com_ctrl)
+ qcom_qmp_phy_configure(tx + cfg->tx_b_lane_offset, cfg->regs,
+ cfg->tx_tbl, cfg->tx_tbl_num);
+
+ qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
+ if (cfg->has_phy_dp_com_ctrl)
+ qcom_qmp_phy_configure(rx + cfg->rx_b_lane_offset, cfg->regs,
+ cfg->rx_tbl, cfg->rx_tbl_num);
+
+ qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
+
+ /*
+ * Pull out PHY from POWER DOWN state.
+ * This is active low enable signal to power-down PHY.
+ */
+ qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+
+ if (cfg->has_pwrdn_delay)
+ usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max);
+
+ /* Pull PHY out of reset state */
+ qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+ if (cfg->has_phy_dp_com_ctrl)
+ qphy_clrbits(dp_com, QPHY_V3_DP_COM_SW_RESET, SW_RESET);
+
+ /* start SerDes and Phy-Coding-Sublayer */
+ qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
+
+ status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
+ mask = cfg->mask_pcs_ready;
+
+ ret = readl_poll_timeout(status, val, !(val & mask), 1,
+ PHY_INIT_COMPLETE_TIMEOUT);
+ if (ret) {
+ dev_err(qmp->dev, "phy initialization timed-out\n");
+ goto err_pcs_ready;
+ }
+ qmp->phy_initialized = true;
+
+ return ret;
+
+err_pcs_ready:
+ clk_disable_unprepare(qphy->pipe_clk);
+err_clk_enable:
+ if (cfg->has_lane_rst)
+ reset_control_assert(qphy->lane_rst);
+err_lane_rst:
+ qcom_qmp_phy_com_exit(qmp);
+
+ return ret;
+}
+
+static int qcom_qmp_phy_exit(struct phy *phy)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+
+ clk_disable_unprepare(qphy->pipe_clk);
+
+ /* PHY reset */
+ qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+
+ /* stop SerDes and Phy-Coding-Sublayer */
+ qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
+
+ /* Put PHY into POWER DOWN state: active low */
+ qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+
+ if (cfg->has_lane_rst)
+ reset_control_assert(qphy->lane_rst);
+
+ qcom_qmp_phy_com_exit(qmp);
+
+ qmp->phy_initialized = false;
+
+ return 0;
+}
+
+static int qcom_qmp_phy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+
+ qmp->mode = mode;
+
+ return 0;
+}
+
+static void qcom_qmp_phy_enable_autonomous_mode(struct qmp_phy *qphy)
+{
+ struct qcom_qmp *qmp = qphy->qmp;
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *pcs = qphy->pcs;
+ void __iomem *pcs_misc = qphy->pcs_misc;
+ u32 intr_mask;
+
+ if (qmp->mode == PHY_MODE_USB_HOST_SS ||
+ qmp->mode == PHY_MODE_USB_DEVICE_SS)
+ intr_mask = ARCVR_DTCT_EN | ALFPS_DTCT_EN;
+ else
+ intr_mask = ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL;
+
+ /* Clear any pending interrupts status */
+ qphy_setbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
+ /* Writing 1 followed by 0 clears the interrupt */
+ qphy_clrbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
+
+ qphy_clrbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL],
+ ARCVR_DTCT_EN | ALFPS_DTCT_EN | ARCVR_DTCT_EVENT_SEL);
+
+ /* Enable required PHY autonomous mode interrupts */
+ qphy_setbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL], intr_mask);
+
+ /* Enable i/o clamp_n for autonomous mode */
+ if (pcs_misc)
+ qphy_clrbits(pcs_misc, QPHY_V3_PCS_MISC_CLAMP_ENABLE, CLAMP_EN);
+}
+
+static void qcom_qmp_phy_disable_autonomous_mode(struct qmp_phy *qphy)
+{
+ struct qcom_qmp *qmp = qphy->qmp;
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *pcs = qphy->pcs;
+ void __iomem *pcs_misc = qphy->pcs_misc;
+
+ /* Disable i/o clamp_n on resume for normal mode */
+ if (pcs_misc)
+ qphy_setbits(pcs_misc, QPHY_V3_PCS_MISC_CLAMP_ENABLE, CLAMP_EN);
+
+ qphy_clrbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL],
+ ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL | ALFPS_DTCT_EN);
+
+ qphy_setbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
+ /* Writing 1 followed by 0 clears the interrupt */
+ qphy_clrbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
+}
+
+static int __maybe_unused qcom_qmp_phy_runtime_suspend(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ struct qmp_phy *qphy = qmp->phys[0];
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+
+ dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qmp->mode);
+
+ /* Supported only for USB3 PHY */
+ if (cfg->type != PHY_TYPE_USB3)
+ return 0;
+
+ if (!qmp->phy_initialized) {
+ dev_vdbg(dev, "PHY not initialized, bailing out\n");
+ return 0;
+ }
+
+ qcom_qmp_phy_enable_autonomous_mode(qphy);
+
+ clk_disable_unprepare(qphy->pipe_clk);
+ clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
+
+ return 0;
+}
+
+static int __maybe_unused qcom_qmp_phy_runtime_resume(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ struct qmp_phy *qphy = qmp->phys[0];
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ int ret = 0;
+
+ dev_vdbg(dev, "Resuming QMP phy, mode:%d\n", qmp->mode);
+
+ /* Supported only for USB3 PHY */
+ if (cfg->type != PHY_TYPE_USB3)
+ return 0;
+
+ if (!qmp->phy_initialized) {
+ dev_vdbg(dev, "PHY not initialized, bailing out\n");
+ return 0;
+ }
+
+ ret = clk_bulk_prepare_enable(cfg->num_clks, qmp->clks);
+ if (ret) {
+ dev_err(qmp->dev, "failed to enable clks, err=%d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(qphy->pipe_clk);
+ if (ret) {
+ dev_err(dev, "pipe_clk enable failed, err=%d\n", ret);
+ clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
+ return ret;
+ }
+
+ qcom_qmp_phy_disable_autonomous_mode(qphy);
+
+ return 0;
+}
+
+static int qcom_qmp_phy_vreg_init(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ int num = qmp->cfg->num_vregs;
+ int i;
+
+ qmp->vregs = devm_kcalloc(dev, num, sizeof(*qmp->vregs), GFP_KERNEL);
+ if (!qmp->vregs)
+ return -ENOMEM;
+
+ for (i = 0; i < num; i++)
+ qmp->vregs[i].supply = qmp->cfg->vreg_list[i];
+
+ return devm_regulator_bulk_get(dev, num, qmp->vregs);
+}
+
+static int qcom_qmp_phy_reset_init(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ int i;
+
+ qmp->resets = devm_kcalloc(dev, qmp->cfg->num_resets,
+ sizeof(*qmp->resets), GFP_KERNEL);
+ if (!qmp->resets)
+ return -ENOMEM;
+
+ for (i = 0; i < qmp->cfg->num_resets; i++) {
+ struct reset_control *rst;
+ const char *name = qmp->cfg->reset_list[i];
+
+ rst = devm_reset_control_get(dev, name);
+ if (IS_ERR(rst)) {
+ dev_err(dev, "failed to get %s reset\n", name);
+ return PTR_ERR(rst);
+ }
+ qmp->resets[i] = rst;
+ }
+
+ return 0;
+}
+
+static int qcom_qmp_phy_clk_init(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ int num = qmp->cfg->num_clks;
+ int i;
+
+ qmp->clks = devm_kcalloc(dev, num, sizeof(*qmp->clks), GFP_KERNEL);
+ if (!qmp->clks)
+ return -ENOMEM;
+
+ for (i = 0; i < num; i++)
+ qmp->clks[i].id = qmp->cfg->clk_list[i];
+
+ return devm_clk_bulk_get(dev, num, qmp->clks);
+}
+
+/*
+ * Register a fixed rate pipe clock.
+ *
+ * The <s>_pipe_clksrc generated by PHY goes to the GCC that gate
+ * controls it. The <s>_pipe_clk coming out of the GCC is requested
+ * by the PHY driver for its operations.
+ * We register the <s>_pipe_clksrc here. The gcc driver takes care
+ * of assigning this <s>_pipe_clksrc as parent to <s>_pipe_clk.
+ * Below picture shows this relationship.
+ *
+ * +---------------+
+ * | PHY block |<<---------------------------------------+
+ * | | |
+ * | +-------+ | +-----+ |
+ * I/P---^-->| PLL |---^--->pipe_clksrc--->| GCC |--->pipe_clk---+
+ * clk | +-------+ | +-----+
+ * +---------------+
+ */
+static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
+{
+ struct clk_fixed_rate *fixed;
+ struct clk_init_data init = { };
+ int ret;
+
+ if ((qmp->cfg->type != PHY_TYPE_USB3) &&
+ (qmp->cfg->type != PHY_TYPE_PCIE)) {
+ /* not all phys register pipe clocks, so return success */
+ return 0;
+ }
+
+ ret = of_property_read_string(np, "clock-output-names", &init.name);
+ if (ret) {
+ dev_err(qmp->dev, "%s: No clock-output-names\n", np->name);
+ return ret;
+ }
+
+ fixed = devm_kzalloc(qmp->dev, sizeof(*fixed), GFP_KERNEL);
+ if (!fixed)
+ return -ENOMEM;
+
+ init.ops = &clk_fixed_rate_ops;
+
+ /* controllers using QMP phys use 125MHz pipe clock interface */
+ fixed->fixed_rate = 125000000;
+ fixed->hw.init = &init;
+
+ return devm_clk_hw_register(qmp->dev, &fixed->hw);
+}
+
+static const struct phy_ops qcom_qmp_phy_gen_ops = {
+ .init = qcom_qmp_phy_init,
+ .exit = qcom_qmp_phy_exit,
+ .set_mode = qcom_qmp_phy_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static
+int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ struct phy *generic_phy;
+ struct qmp_phy *qphy;
+ char prop_name[MAX_PROP_NAME];
+ int ret;
+
+ qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
+ if (!qphy)
+ return -ENOMEM;
+
+ /*
+ * Get memory resources for each phy lane:
+ * Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2; and
+ * pcs_misc (optional) -> 3.
+ */
+ qphy->tx = of_iomap(np, 0);
+ if (!qphy->tx)
+ return -ENOMEM;
+
+ qphy->rx = of_iomap(np, 1);
+ if (!qphy->rx)
+ return -ENOMEM;
+
+ qphy->pcs = of_iomap(np, 2);
+ if (!qphy->pcs)
+ return -ENOMEM;
+
+ qphy->pcs_misc = of_iomap(np, 3);
+ if (!qphy->pcs_misc)
+ dev_vdbg(dev, "PHY pcs_misc-reg not used\n");
+
+ /*
+ * Get PHY's Pipe clock, if any. USB3 and PCIe are PIPE3
+ * based phys, so they essentially have pipe clock. So,
+ * we return error in case phy is USB3 or PIPE type.
+ * Otherwise, we initialize pipe clock to NULL for
+ * all phys that don't need this.
+ */
+ snprintf(prop_name, sizeof(prop_name), "pipe%d", id);
+ qphy->pipe_clk = of_clk_get_by_name(np, prop_name);
+ if (IS_ERR(qphy->pipe_clk)) {
+ if (qmp->cfg->type == PHY_TYPE_PCIE ||
+ qmp->cfg->type == PHY_TYPE_USB3) {
+ ret = PTR_ERR(qphy->pipe_clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev,
+ "failed to get lane%d pipe_clk, %d\n",
+ id, ret);
+ return ret;
+ }
+ qphy->pipe_clk = NULL;
+ }
+
+ /* Get lane reset, if any */
+ if (qmp->cfg->has_lane_rst) {
+ snprintf(prop_name, sizeof(prop_name), "lane%d", id);
+ qphy->lane_rst = of_reset_control_get(np, prop_name);
+ if (IS_ERR(qphy->lane_rst)) {
+ dev_err(dev, "failed to get lane%d reset\n", id);
+ return PTR_ERR(qphy->lane_rst);
+ }
+ }
+
+ generic_phy = devm_phy_create(dev, np, &qcom_qmp_phy_gen_ops);
+ if (IS_ERR(generic_phy)) {
+ ret = PTR_ERR(generic_phy);
+ dev_err(dev, "failed to create qphy %d\n", ret);
+ return ret;
+ }
+
+ qphy->phy = generic_phy;
+ qphy->index = id;
+ qphy->qmp = qmp;
+ qmp->phys[id] = qphy;
+ phy_set_drvdata(generic_phy, qphy);
+
+ return 0;
+}
+
+static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
+ {
+ .compatible = "qcom,msm8996-qmp-pcie-phy",
+ .data = &msm8996_pciephy_cfg,
+ }, {
+ .compatible = "qcom,msm8996-qmp-usb3-phy",
+ .data = &msm8996_usb3phy_cfg,
+ }, {
+ .compatible = "qcom,ipq8074-qmp-pcie-phy",
+ .data = &ipq8074_pciephy_cfg,
+ }, {
+ .compatible = "qcom,sdm845-qmp-usb3-phy",
+ .data = &qmp_v3_usb3phy_cfg,
+ }, {
+ .compatible = "qcom,sdm845-qmp-usb3-uni-phy",
+ .data = &qmp_v3_usb3_uniphy_cfg,
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_qmp_phy_of_match_table);
+
+static const struct dev_pm_ops qcom_qmp_phy_pm_ops = {
+ SET_RUNTIME_PM_OPS(qcom_qmp_phy_runtime_suspend,
+ qcom_qmp_phy_runtime_resume, NULL)
+};
+
+static int qcom_qmp_phy_probe(struct platform_device *pdev)
+{
+ struct qcom_qmp *qmp;
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct device_node *child;
+ struct phy_provider *phy_provider;
+ void __iomem *base;
+ int num, id;
+ int ret;
+
+ qmp = devm_kzalloc(dev, sizeof(*qmp), GFP_KERNEL);
+ if (!qmp)
+ return -ENOMEM;
+
+ qmp->dev = dev;
+ dev_set_drvdata(dev, qmp);
+
+ /* Get the specific init parameters of QMP phy */
+ qmp->cfg = of_device_get_match_data(dev);
+ if (!qmp->cfg)
+ return -EINVAL;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ /* per PHY serdes; usually located at base address */
+ qmp->serdes = base;
+
+ /* per PHY dp_com; if PHY has dp_com control block */
+ if (qmp->cfg->has_phy_dp_com_ctrl) {
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "dp_com");
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ qmp->dp_com = base;
+ }
+
+ mutex_init(&qmp->phy_mutex);
+
+ ret = qcom_qmp_phy_clk_init(dev);
+ if (ret)
+ return ret;
+
+ ret = qcom_qmp_phy_reset_init(dev);
+ if (ret)
+ return ret;
+
+ ret = qcom_qmp_phy_vreg_init(dev);
+ if (ret) {
+ dev_err(dev, "failed to get regulator supplies\n");
+ return ret;
+ }
+
+ num = of_get_available_child_count(dev->of_node);
+ /* do we have a rogue child node ? */
+ if (num > qmp->cfg->nlanes)
+ return -EINVAL;
+
+ qmp->phys = devm_kcalloc(dev, num, sizeof(*qmp->phys), GFP_KERNEL);
+ if (!qmp->phys)
+ return -ENOMEM;
+
+ id = 0;
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+ /*
+ * Prevent runtime pm from being ON by default. Users can enable
+ * it using power/control in sysfs.
+ */
+ pm_runtime_forbid(dev);
+
+ for_each_available_child_of_node(dev->of_node, child) {
+ /* Create per-lane phy */
+ ret = qcom_qmp_phy_create(dev, child, id);
+ if (ret) {
+ dev_err(dev, "failed to create lane%d phy, %d\n",
+ id, ret);
+ pm_runtime_disable(dev);
+ return ret;
+ }
+
+ /*
+ * Register the pipe clock provided by phy.
+ * See function description to see details of this pipe clock.
+ */
+ ret = phy_pipe_clk_register(qmp, child);
+ if (ret) {
+ dev_err(qmp->dev,
+ "failed to register pipe clock source\n");
+ pm_runtime_disable(dev);
+ return ret;
+ }
+ id++;
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (!IS_ERR(phy_provider))
+ dev_info(dev, "Registered Qcom-QMP phy\n");
+ else
+ pm_runtime_disable(dev);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver qcom_qmp_phy_driver = {
+ .probe = qcom_qmp_phy_probe,
+ .driver = {
+ .name = "qcom-qmp-phy",
+ .pm = &qcom_qmp_phy_pm_ops,
+ .of_match_table = qcom_qmp_phy_of_match_table,
+ },
+};
+
+module_platform_driver(qcom_qmp_phy_driver);
+
+MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>");
+MODULE_DESCRIPTION("Qualcomm QMP PHY driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
new file mode 100644
index 0000000..5d78d43
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_H_
+#define QCOM_PHY_QMP_H_
+
+/* Only for QMP V2 PHY - QSERDES COM registers */
+#define QSERDES_COM_BG_TIMER 0x00c
+#define QSERDES_COM_SSC_EN_CENTER 0x010
+#define QSERDES_COM_SSC_ADJ_PER1 0x014
+#define QSERDES_COM_SSC_ADJ_PER2 0x018
+#define QSERDES_COM_SSC_PER1 0x01c
+#define QSERDES_COM_SSC_PER2 0x020
+#define QSERDES_COM_SSC_STEP_SIZE1 0x024
+#define QSERDES_COM_SSC_STEP_SIZE2 0x028
+#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN 0x034
+#define QSERDES_COM_CLK_ENABLE1 0x038
+#define QSERDES_COM_SYS_CLK_CTRL 0x03c
+#define QSERDES_COM_SYSCLK_BUF_ENABLE 0x040
+#define QSERDES_COM_PLL_IVCO 0x048
+#define QSERDES_COM_LOCK_CMP1_MODE0 0x04c
+#define QSERDES_COM_LOCK_CMP2_MODE0 0x050
+#define QSERDES_COM_LOCK_CMP3_MODE0 0x054
+#define QSERDES_COM_LOCK_CMP1_MODE1 0x058
+#define QSERDES_COM_LOCK_CMP2_MODE1 0x05c
+#define QSERDES_COM_LOCK_CMP3_MODE1 0x060
+#define QSERDES_COM_BG_TRIM 0x070
+#define QSERDES_COM_CLK_EP_DIV 0x074
+#define QSERDES_COM_CP_CTRL_MODE0 0x078
+#define QSERDES_COM_CP_CTRL_MODE1 0x07c
+#define QSERDES_COM_PLL_RCTRL_MODE0 0x084
+#define QSERDES_COM_PLL_RCTRL_MODE1 0x088
+#define QSERDES_COM_PLL_CCTRL_MODE0 0x090
+#define QSERDES_COM_PLL_CCTRL_MODE1 0x094
+#define QSERDES_COM_BIAS_EN_CTRL_BY_PSM 0x0a8
+#define QSERDES_COM_SYSCLK_EN_SEL 0x0ac
+#define QSERDES_COM_RESETSM_CNTRL 0x0b4
+#define QSERDES_COM_RESTRIM_CTRL 0x0bc
+#define QSERDES_COM_RESCODE_DIV_NUM 0x0c4
+#define QSERDES_COM_LOCK_CMP_EN 0x0c8
+#define QSERDES_COM_LOCK_CMP_CFG 0x0cc
+#define QSERDES_COM_DEC_START_MODE0 0x0d0
+#define QSERDES_COM_DEC_START_MODE1 0x0d4
+#define QSERDES_COM_DIV_FRAC_START1_MODE0 0x0dc
+#define QSERDES_COM_DIV_FRAC_START2_MODE0 0x0e0
+#define QSERDES_COM_DIV_FRAC_START3_MODE0 0x0e4
+#define QSERDES_COM_DIV_FRAC_START1_MODE1 0x0e8
+#define QSERDES_COM_DIV_FRAC_START2_MODE1 0x0ec
+#define QSERDES_COM_DIV_FRAC_START3_MODE1 0x0f0
+#define QSERDES_COM_INTEGLOOP_GAIN0_MODE0 0x108
+#define QSERDES_COM_INTEGLOOP_GAIN1_MODE0 0x10c
+#define QSERDES_COM_INTEGLOOP_GAIN0_MODE1 0x110
+#define QSERDES_COM_INTEGLOOP_GAIN1_MODE1 0x114
+#define QSERDES_COM_VCO_TUNE_CTRL 0x124
+#define QSERDES_COM_VCO_TUNE_MAP 0x128
+#define QSERDES_COM_VCO_TUNE1_MODE0 0x12c
+#define QSERDES_COM_VCO_TUNE2_MODE0 0x130
+#define QSERDES_COM_VCO_TUNE1_MODE1 0x134
+#define QSERDES_COM_VCO_TUNE2_MODE1 0x138
+#define QSERDES_COM_VCO_TUNE_TIMER1 0x144
+#define QSERDES_COM_VCO_TUNE_TIMER2 0x148
+#define QSERDES_COM_BG_CTRL 0x170
+#define QSERDES_COM_CLK_SELECT 0x174
+#define QSERDES_COM_HSCLK_SEL 0x178
+#define QSERDES_COM_CORECLK_DIV 0x184
+#define QSERDES_COM_CORE_CLK_EN 0x18c
+#define QSERDES_COM_C_READY_STATUS 0x190
+#define QSERDES_COM_CMN_CONFIG 0x194
+#define QSERDES_COM_SVS_MODE_CLK_SEL 0x19c
+#define QSERDES_COM_DEBUG_BUS0 0x1a0
+#define QSERDES_COM_DEBUG_BUS1 0x1a4
+#define QSERDES_COM_DEBUG_BUS2 0x1a8
+#define QSERDES_COM_DEBUG_BUS3 0x1ac
+#define QSERDES_COM_DEBUG_BUS_SEL 0x1b0
+#define QSERDES_COM_CORECLK_DIV_MODE1 0x1bc
+
+/* Only for QMP V2 PHY - TX registers */
+#define QSERDES_TX_RES_CODE_LANE_OFFSET 0x054
+#define QSERDES_TX_DEBUG_BUS_SEL 0x064
+#define QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN 0x068
+#define QSERDES_TX_LANE_MODE 0x094
+#define QSERDES_TX_RCV_DETECT_LVL_2 0x0ac
+
+/* Only for QMP V2 PHY - RX registers */
+#define QSERDES_RX_UCDR_SO_GAIN_HALF 0x010
+#define QSERDES_RX_UCDR_SO_GAIN 0x01c
+#define QSERDES_RX_UCDR_FASTLOCK_FO_GAIN 0x040
+#define QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE 0x048
+#define QSERDES_RX_RX_TERM_BW 0x090
+#define QSERDES_RX_RX_EQ_GAIN1_LSB 0x0c4
+#define QSERDES_RX_RX_EQ_GAIN1_MSB 0x0c8
+#define QSERDES_RX_RX_EQ_GAIN2_LSB 0x0cc
+#define QSERDES_RX_RX_EQ_GAIN2_MSB 0x0d0
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2 0x0d8
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3 0x0dc
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4 0x0e0
+#define QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x108
+#define QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2 0x10c
+#define QSERDES_RX_SIGDET_ENABLES 0x110
+#define QSERDES_RX_SIGDET_CNTRL 0x114
+#define QSERDES_RX_SIGDET_LVL 0x118
+#define QSERDES_RX_SIGDET_DEGLITCH_CNTRL 0x11c
+#define QSERDES_RX_RX_BAND 0x120
+#define QSERDES_RX_RX_INTERFACE_MODE 0x12c
+
+/* Only for QMP V2 PHY - PCS registers */
+#define QPHY_POWER_DOWN_CONTROL 0x04
+#define QPHY_TXDEEMPH_M6DB_V0 0x24
+#define QPHY_TXDEEMPH_M3P5DB_V0 0x28
+#define QPHY_ENDPOINT_REFCLK_DRIVE 0x54
+#define QPHY_RX_IDLE_DTCT_CNTRL 0x58
+#define QPHY_POWER_STATE_CONFIG1 0x60
+#define QPHY_POWER_STATE_CONFIG2 0x64
+#define QPHY_POWER_STATE_CONFIG4 0x6c
+#define QPHY_LOCK_DETECT_CONFIG1 0x80
+#define QPHY_LOCK_DETECT_CONFIG2 0x84
+#define QPHY_LOCK_DETECT_CONFIG3 0x88
+#define QPHY_PWRUP_RESET_DLY_TIME_AUXCLK 0xa0
+#define QPHY_LP_WAKEUP_DLY_TIME_AUXCLK 0xa4
+#define QPHY_PLL_LOCK_CHK_DLY_TIME_AUXCLK_LSB 0x1A8
+#define QPHY_OSC_DTCT_ACTIONS 0x1AC
+#define QPHY_RX_SIGDET_LVL 0x1D8
+#define QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB 0x1DC
+#define QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB 0x1E0
+
+/* Only for QMP V3 PHY - DP COM registers */
+#define QPHY_V3_DP_COM_PHY_MODE_CTRL 0x00
+#define QPHY_V3_DP_COM_SW_RESET 0x04
+#define QPHY_V3_DP_COM_POWER_DOWN_CTRL 0x08
+#define QPHY_V3_DP_COM_SWI_CTRL 0x0c
+#define QPHY_V3_DP_COM_TYPEC_CTRL 0x10
+#define QPHY_V3_DP_COM_TYPEC_PWRDN_CTRL 0x14
+#define QPHY_V3_DP_COM_RESET_OVRD_CTRL 0x1c
+
+/* Only for QMP V3 PHY - QSERDES COM registers */
+#define QSERDES_V3_COM_BG_TIMER 0x00c
+#define QSERDES_V3_COM_SSC_EN_CENTER 0x010
+#define QSERDES_V3_COM_SSC_ADJ_PER1 0x014
+#define QSERDES_V3_COM_SSC_ADJ_PER2 0x018
+#define QSERDES_V3_COM_SSC_PER1 0x01c
+#define QSERDES_V3_COM_SSC_PER2 0x020
+#define QSERDES_V3_COM_SSC_STEP_SIZE1 0x024
+#define QSERDES_V3_COM_SSC_STEP_SIZE2 0x028
+#define QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN 0x034
+#define QSERDES_V3_COM_CLK_ENABLE1 0x038
+#define QSERDES_V3_COM_SYS_CLK_CTRL 0x03c
+#define QSERDES_V3_COM_SYSCLK_BUF_ENABLE 0x040
+#define QSERDES_V3_COM_PLL_IVCO 0x048
+#define QSERDES_V3_COM_LOCK_CMP1_MODE0 0x098
+#define QSERDES_V3_COM_LOCK_CMP2_MODE0 0x09c
+#define QSERDES_V3_COM_LOCK_CMP3_MODE0 0x0a0
+#define QSERDES_V3_COM_LOCK_CMP1_MODE1 0x0a4
+#define QSERDES_V3_COM_LOCK_CMP2_MODE1 0x0a8
+#define QSERDES_V3_COM_LOCK_CMP3_MODE1 0x0ac
+#define QSERDES_V3_COM_CLK_EP_DIV 0x05c
+#define QSERDES_V3_COM_CP_CTRL_MODE0 0x060
+#define QSERDES_V3_COM_CP_CTRL_MODE1 0x064
+#define QSERDES_V3_COM_PLL_RCTRL_MODE0 0x068
+#define QSERDES_V3_COM_PLL_RCTRL_MODE1 0x06c
+#define QSERDES_V3_COM_PLL_CCTRL_MODE0 0x070
+#define QSERDES_V3_COM_PLL_CCTRL_MODE1 0x074
+#define QSERDES_V3_COM_SYSCLK_EN_SEL 0x080
+#define QSERDES_V3_COM_RESETSM_CNTRL 0x088
+#define QSERDES_V3_COM_RESETSM_CNTRL2 0x08c
+#define QSERDES_V3_COM_LOCK_CMP_EN 0x090
+#define QSERDES_V3_COM_LOCK_CMP_CFG 0x094
+#define QSERDES_V3_COM_DEC_START_MODE0 0x0b0
+#define QSERDES_V3_COM_DEC_START_MODE1 0x0b4
+#define QSERDES_V3_COM_DIV_FRAC_START1_MODE0 0x0b8
+#define QSERDES_V3_COM_DIV_FRAC_START2_MODE0 0x0bc
+#define QSERDES_V3_COM_DIV_FRAC_START3_MODE0 0x0c0
+#define QSERDES_V3_COM_DIV_FRAC_START1_MODE1 0x0c4
+#define QSERDES_V3_COM_DIV_FRAC_START2_MODE1 0x0c8
+#define QSERDES_V3_COM_DIV_FRAC_START3_MODE1 0x0cc
+#define QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0 0x0d8
+#define QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0 0x0dc
+#define QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE1 0x0e0
+#define QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE1 0x0e4
+#define QSERDES_V3_COM_VCO_TUNE_CTRL 0x0ec
+#define QSERDES_V3_COM_VCO_TUNE_MAP 0x0f0
+#define QSERDES_V3_COM_VCO_TUNE1_MODE0 0x0f4
+#define QSERDES_V3_COM_VCO_TUNE2_MODE0 0x0f8
+#define QSERDES_V3_COM_VCO_TUNE1_MODE1 0x0fc
+#define QSERDES_V3_COM_VCO_TUNE2_MODE1 0x100
+#define QSERDES_V3_COM_VCO_TUNE_TIMER1 0x11c
+#define QSERDES_V3_COM_VCO_TUNE_TIMER2 0x120
+#define QSERDES_V3_COM_CLK_SELECT 0x138
+#define QSERDES_V3_COM_HSCLK_SEL 0x13c
+#define QSERDES_V3_COM_CORECLK_DIV_MODE0 0x148
+#define QSERDES_V3_COM_CORECLK_DIV_MODE1 0x14c
+#define QSERDES_V3_COM_CORE_CLK_EN 0x154
+#define QSERDES_V3_COM_C_READY_STATUS 0x158
+#define QSERDES_V3_COM_CMN_CONFIG 0x15c
+#define QSERDES_V3_COM_SVS_MODE_CLK_SEL 0x164
+#define QSERDES_V3_COM_DEBUG_BUS0 0x168
+#define QSERDES_V3_COM_DEBUG_BUS1 0x16c
+#define QSERDES_V3_COM_DEBUG_BUS2 0x170
+#define QSERDES_V3_COM_DEBUG_BUS3 0x174
+#define QSERDES_V3_COM_DEBUG_BUS_SEL 0x178
+
+/* Only for QMP V3 PHY - TX registers */
+#define QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX 0x044
+#define QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX 0x048
+#define QSERDES_V3_TX_DEBUG_BUS_SEL 0x058
+#define QSERDES_V3_TX_HIGHZ_DRVR_EN 0x060
+#define QSERDES_V3_TX_LANE_MODE_1 0x08c
+#define QSERDES_V3_TX_RCV_DETECT_LVL_2 0x0a4
+
+/* Only for QMP V3 PHY - RX registers */
+#define QSERDES_V3_RX_UCDR_SO_GAIN_HALF 0x00c
+#define QSERDES_V3_RX_UCDR_SO_GAIN 0x014
+#define QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN 0x030
+#define QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE 0x034
+#define QSERDES_V3_RX_RX_TERM_BW 0x07c
+#define QSERDES_V3_RX_VGA_CAL_CNTRL1 0x0bc
+#define QSERDES_V3_RX_VGA_CAL_CNTRL2 0x0c0
+#define QSERDES_V3_RX_RX_EQ_GAIN2_LSB 0x0c8
+#define QSERDES_V3_RX_RX_EQ_GAIN2_MSB 0x0cc
+#define QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2 0x0d4
+#define QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3 0x0d8
+#define QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4 0x0dc
+#define QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x0f8
+#define QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2 0x0fc
+#define QSERDES_V3_RX_SIGDET_ENABLES 0x100
+#define QSERDES_V3_RX_SIGDET_CNTRL 0x104
+#define QSERDES_V3_RX_SIGDET_LVL 0x108
+#define QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL 0x10c
+#define QSERDES_V3_RX_RX_BAND 0x110
+#define QSERDES_V3_RX_RX_INTERFACE_MODE 0x11c
+#define QSERDES_V3_RX_RX_MODE_00 0x164
+
+/* Only for QMP V3 PHY - PCS registers */
+#define QPHY_V3_PCS_POWER_DOWN_CONTROL 0x004
+#define QPHY_V3_PCS_TXMGN_V0 0x00c
+#define QPHY_V3_PCS_TXMGN_V1 0x010
+#define QPHY_V3_PCS_TXMGN_V2 0x014
+#define QPHY_V3_PCS_TXMGN_V3 0x018
+#define QPHY_V3_PCS_TXMGN_V4 0x01c
+#define QPHY_V3_PCS_TXMGN_LS 0x020
+#define QPHY_V3_PCS_TXDEEMPH_M6DB_V0 0x024
+#define QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0 0x028
+#define QPHY_V3_PCS_TXDEEMPH_M6DB_V1 0x02c
+#define QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1 0x030
+#define QPHY_V3_PCS_TXDEEMPH_M6DB_V2 0x034
+#define QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2 0x038
+#define QPHY_V3_PCS_TXDEEMPH_M6DB_V3 0x03c
+#define QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3 0x040
+#define QPHY_V3_PCS_TXDEEMPH_M6DB_V4 0x044
+#define QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4 0x048
+#define QPHY_V3_PCS_TXDEEMPH_M6DB_LS 0x04c
+#define QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS 0x050
+#define QPHY_V3_PCS_ENDPOINT_REFCLK_DRIVE 0x054
+#define QPHY_V3_PCS_RX_IDLE_DTCT_CNTRL 0x058
+#define QPHY_V3_PCS_RATE_SLEW_CNTRL 0x05c
+#define QPHY_V3_PCS_POWER_STATE_CONFIG1 0x060
+#define QPHY_V3_PCS_POWER_STATE_CONFIG2 0x064
+#define QPHY_V3_PCS_POWER_STATE_CONFIG4 0x06c
+#define QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L 0x070
+#define QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H 0x074
+#define QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L 0x078
+#define QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H 0x07c
+#define QPHY_V3_PCS_LOCK_DETECT_CONFIG1 0x080
+#define QPHY_V3_PCS_LOCK_DETECT_CONFIG2 0x084
+#define QPHY_V3_PCS_LOCK_DETECT_CONFIG3 0x088
+#define QPHY_V3_PCS_TSYNC_RSYNC_TIME 0x08c
+#define QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK 0x0a0
+#define QPHY_V3_PCS_LP_WAKEUP_DLY_TIME_AUXCLK 0x0a4
+#define QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK 0x0b0
+#define QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME 0x0b8
+#define QPHY_V3_PCS_RXEQTRAINING_RUN_TIME 0x0bc
+#define QPHY_V3_PCS_FLL_CNTRL1 0x0c4
+#define QPHY_V3_PCS_FLL_CNTRL2 0x0c8
+#define QPHY_V3_PCS_FLL_CNT_VAL_L 0x0cc
+#define QPHY_V3_PCS_FLL_CNT_VAL_H_TOL 0x0d0
+#define QPHY_V3_PCS_FLL_MAN_CODE 0x0d4
+#define QPHY_V3_PCS_RX_SIGDET_LVL 0x1d8
+#define QPHY_V3_PCS_REFGEN_REQ_CONFIG1 0x20c
+#define QPHY_V3_PCS_REFGEN_REQ_CONFIG2 0x210
+
+/* Only for QMP V3 PHY - PCS_MISC registers */
+#define QPHY_V3_PCS_MISC_CLAMP_ENABLE 0x0c
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
new file mode 100644
index 0000000..69c9284
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
@@ -0,0 +1,893 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#include <dt-bindings/phy/phy-qcom-qusb2.h>
+
+#define QUSB2PHY_PLL_TEST 0x04
+#define CLK_REF_SEL BIT(7)
+
+#define QUSB2PHY_PLL_TUNE 0x08
+#define QUSB2PHY_PLL_USER_CTL1 0x0c
+#define QUSB2PHY_PLL_USER_CTL2 0x10
+#define QUSB2PHY_PLL_AUTOPGM_CTL1 0x1c
+#define QUSB2PHY_PLL_PWR_CTRL 0x18
+
+/* QUSB2PHY_PLL_STATUS register bits */
+#define PLL_LOCKED BIT(5)
+
+/* QUSB2PHY_PLL_COMMON_STATUS_ONE register bits */
+#define CORE_READY_STATUS BIT(0)
+
+/* QUSB2PHY_PORT_POWERDOWN register bits */
+#define CLAMP_N_EN BIT(5)
+#define FREEZIO_N BIT(1)
+#define POWER_DOWN BIT(0)
+
+/* QUSB2PHY_PWR_CTRL1 register bits */
+#define PWR_CTRL1_VREF_SUPPLY_TRIM BIT(5)
+#define PWR_CTRL1_CLAMP_N_EN BIT(1)
+
+#define QUSB2PHY_REFCLK_ENABLE BIT(0)
+
+#define PHY_CLK_SCHEME_SEL BIT(0)
+
+/* QUSB2PHY_INTR_CTRL register bits */
+#define DMSE_INTR_HIGH_SEL BIT(4)
+#define DPSE_INTR_HIGH_SEL BIT(3)
+#define CHG_DET_INTR_EN BIT(2)
+#define DMSE_INTR_EN BIT(1)
+#define DPSE_INTR_EN BIT(0)
+
+/* QUSB2PHY_PLL_CORE_INPUT_OVERRIDE register bits */
+#define CORE_PLL_EN_FROM_RESET BIT(4)
+#define CORE_RESET BIT(5)
+#define CORE_RESET_MUX BIT(6)
+
+/* QUSB2PHY_IMP_CTRL1 register bits */
+#define IMP_RES_OFFSET_MASK GENMASK(5, 0)
+#define IMP_RES_OFFSET_SHIFT 0x0
+
+/* QUSB2PHY_PORT_TUNE1 register bits */
+#define HSTX_TRIM_MASK GENMASK(7, 4)
+#define HSTX_TRIM_SHIFT 0x4
+#define PREEMPH_WIDTH_HALF_BIT BIT(2)
+#define PREEMPHASIS_EN_MASK GENMASK(1, 0)
+#define PREEMPHASIS_EN_SHIFT 0x0
+
+#define QUSB2PHY_PLL_ANALOG_CONTROLS_TWO 0x04
+#define QUSB2PHY_PLL_CLOCK_INVERTERS 0x18c
+#define QUSB2PHY_PLL_CMODE 0x2c
+#define QUSB2PHY_PLL_LOCK_DELAY 0x184
+#define QUSB2PHY_PLL_DIGITAL_TIMERS_TWO 0xb4
+#define QUSB2PHY_PLL_BIAS_CONTROL_1 0x194
+#define QUSB2PHY_PLL_BIAS_CONTROL_2 0x198
+#define QUSB2PHY_PWR_CTRL2 0x214
+#define QUSB2PHY_IMP_CTRL1 0x220
+#define QUSB2PHY_IMP_CTRL2 0x224
+#define QUSB2PHY_CHG_CTRL2 0x23c
+
+struct qusb2_phy_init_tbl {
+ unsigned int offset;
+ unsigned int val;
+ /*
+ * register part of layout ?
+ * if yes, then offset gives index in the reg-layout
+ */
+ int in_layout;
+};
+
+#define QUSB2_PHY_INIT_CFG(o, v) \
+ { \
+ .offset = o, \
+ .val = v, \
+ }
+
+#define QUSB2_PHY_INIT_CFG_L(o, v) \
+ { \
+ .offset = o, \
+ .val = v, \
+ .in_layout = 1, \
+ }
+
+/* set of registers with offsets different per-PHY */
+enum qusb2phy_reg_layout {
+ QUSB2PHY_PLL_CORE_INPUT_OVERRIDE,
+ QUSB2PHY_PLL_STATUS,
+ QUSB2PHY_PORT_TUNE1,
+ QUSB2PHY_PORT_TUNE2,
+ QUSB2PHY_PORT_TUNE3,
+ QUSB2PHY_PORT_TUNE4,
+ QUSB2PHY_PORT_TUNE5,
+ QUSB2PHY_PORT_TEST1,
+ QUSB2PHY_PORT_TEST2,
+ QUSB2PHY_PORT_POWERDOWN,
+ QUSB2PHY_INTR_CTRL,
+};
+
+static const unsigned int msm8996_regs_layout[] = {
+ [QUSB2PHY_PLL_STATUS] = 0x38,
+ [QUSB2PHY_PORT_TUNE1] = 0x80,
+ [QUSB2PHY_PORT_TUNE2] = 0x84,
+ [QUSB2PHY_PORT_TUNE3] = 0x88,
+ [QUSB2PHY_PORT_TUNE4] = 0x8c,
+ [QUSB2PHY_PORT_TUNE5] = 0x90,
+ [QUSB2PHY_PORT_TEST1] = 0xb8,
+ [QUSB2PHY_PORT_TEST2] = 0x9c,
+ [QUSB2PHY_PORT_POWERDOWN] = 0xb4,
+ [QUSB2PHY_INTR_CTRL] = 0xbc,
+};
+
+static const struct qusb2_phy_init_tbl msm8996_init_tbl[] = {
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xf8),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0xb3),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0x83),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0xc0),
+
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21),
+
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TEST2, 0x14),
+
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9f),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00),
+};
+
+static const unsigned int sdm845_regs_layout[] = {
+ [QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8,
+ [QUSB2PHY_PLL_STATUS] = 0x1a0,
+ [QUSB2PHY_PORT_TUNE1] = 0x240,
+ [QUSB2PHY_PORT_TUNE2] = 0x244,
+ [QUSB2PHY_PORT_TUNE3] = 0x248,
+ [QUSB2PHY_PORT_TUNE4] = 0x24c,
+ [QUSB2PHY_PORT_TUNE5] = 0x250,
+ [QUSB2PHY_PORT_TEST1] = 0x254,
+ [QUSB2PHY_PORT_TEST2] = 0x258,
+ [QUSB2PHY_PORT_POWERDOWN] = 0x210,
+ [QUSB2PHY_INTR_CTRL] = 0x230,
+};
+
+static const struct qusb2_phy_init_tbl sdm845_init_tbl[] = {
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x03),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_1, 0x40),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_2, 0x20),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PWR_CTRL2, 0x21),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL1, 0x0),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL2, 0x58),
+
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0x30),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x29),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0xca),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0x04),
+ QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x03),
+
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0),
+};
+
+struct qusb2_phy_cfg {
+ const struct qusb2_phy_init_tbl *tbl;
+ /* number of entries in the table */
+ unsigned int tbl_num;
+ /* offset to PHY_CLK_SCHEME register in TCSR map */
+ unsigned int clk_scheme_offset;
+
+ /* array of registers with different offsets */
+ const unsigned int *regs;
+ unsigned int mask_core_ready;
+ unsigned int disable_ctrl;
+ unsigned int autoresume_en;
+
+ /* true if PHY has PLL_TEST register to select clk_scheme */
+ bool has_pll_test;
+
+ /* true if TUNE1 register must be updated by fused value, else TUNE2 */
+ bool update_tune1_with_efuse;
+
+ /* true if PHY has PLL_CORE_INPUT_OVERRIDE register to reset PLL */
+ bool has_pll_override;
+};
+
+static const struct qusb2_phy_cfg msm8996_phy_cfg = {
+ .tbl = msm8996_init_tbl,
+ .tbl_num = ARRAY_SIZE(msm8996_init_tbl),
+ .regs = msm8996_regs_layout,
+
+ .has_pll_test = true,
+ .disable_ctrl = (CLAMP_N_EN | FREEZIO_N | POWER_DOWN),
+ .mask_core_ready = PLL_LOCKED,
+ .autoresume_en = BIT(3),
+};
+
+static const struct qusb2_phy_cfg sdm845_phy_cfg = {
+ .tbl = sdm845_init_tbl,
+ .tbl_num = ARRAY_SIZE(sdm845_init_tbl),
+ .regs = sdm845_regs_layout,
+
+ .disable_ctrl = (PWR_CTRL1_VREF_SUPPLY_TRIM | PWR_CTRL1_CLAMP_N_EN |
+ POWER_DOWN),
+ .mask_core_ready = CORE_READY_STATUS,
+ .has_pll_override = true,
+ .autoresume_en = BIT(0),
+ .update_tune1_with_efuse = true,
+};
+
+static const char * const qusb2_phy_vreg_names[] = {
+ "vdda-pll", "vdda-phy-dpdm",
+};
+
+#define QUSB2_NUM_VREGS ARRAY_SIZE(qusb2_phy_vreg_names)
+
+/**
+ * struct qusb2_phy - structure holding qusb2 phy attributes
+ *
+ * @phy: generic phy
+ * @base: iomapped memory space for qubs2 phy
+ *
+ * @cfg_ahb_clk: AHB2PHY interface clock
+ * @ref_clk: phy reference clock
+ * @iface_clk: phy interface clock
+ * @phy_reset: phy reset control
+ * @vregs: regulator supplies bulk data
+ *
+ * @tcsr: TCSR syscon register map
+ * @cell: nvmem cell containing phy tuning value
+ *
+ * @override_imp_res_offset: PHY should use different rescode offset
+ * @imp_res_offset_value: rescode offset to be updated in IMP_CTRL1 register
+ * @override_hstx_trim: PHY should use different HSTX o/p current value
+ * @hstx_trim_value: HSTX_TRIM value to be updated in TUNE1 register
+ * @override_preemphasis: PHY should use different pre-amphasis amplitude
+ * @preemphasis_level: Amplitude Pre-Emphasis to be updated in TUNE1 register
+ * @override_preemphasis_width: PHY should use different pre-emphasis duration
+ * @preemphasis_width: half/full-width Pre-Emphasis updated via TUNE1
+ *
+ * @cfg: phy config data
+ * @has_se_clk_scheme: indicate if PHY has single-ended ref clock scheme
+ * @phy_initialized: indicate if PHY has been initialized
+ * @mode: current PHY mode
+ */
+struct qusb2_phy {
+ struct phy *phy;
+ void __iomem *base;
+
+ struct clk *cfg_ahb_clk;
+ struct clk *ref_clk;
+ struct clk *iface_clk;
+ struct reset_control *phy_reset;
+ struct regulator_bulk_data vregs[QUSB2_NUM_VREGS];
+
+ struct regmap *tcsr;
+ struct nvmem_cell *cell;
+
+ bool override_imp_res_offset;
+ u8 imp_res_offset_value;
+ bool override_hstx_trim;
+ u8 hstx_trim_value;
+ bool override_preemphasis;
+ u8 preemphasis_level;
+ bool override_preemphasis_width;
+ u8 preemphasis_width;
+
+ const struct qusb2_phy_cfg *cfg;
+ bool has_se_clk_scheme;
+ bool phy_initialized;
+ enum phy_mode mode;
+};
+
+static inline void qusb2_write_mask(void __iomem *base, u32 offset,
+ u32 val, u32 mask)
+{
+ u32 reg;
+
+ reg = readl(base + offset);
+ reg &= ~mask;
+ reg |= val & mask;
+ writel(reg, base + offset);
+
+ /* Ensure above write is completed */
+ readl(base + offset);
+}
+
+static inline void qusb2_setbits(void __iomem *base, u32 offset, u32 val)
+{
+ u32 reg;
+
+ reg = readl(base + offset);
+ reg |= val;
+ writel(reg, base + offset);
+
+ /* Ensure above write is completed */
+ readl(base + offset);
+}
+
+static inline void qusb2_clrbits(void __iomem *base, u32 offset, u32 val)
+{
+ u32 reg;
+
+ reg = readl(base + offset);
+ reg &= ~val;
+ writel(reg, base + offset);
+
+ /* Ensure above write is completed */
+ readl(base + offset);
+}
+
+static inline
+void qcom_qusb2_phy_configure(void __iomem *base,
+ const unsigned int *regs,
+ const struct qusb2_phy_init_tbl tbl[], int num)
+{
+ int i;
+
+ for (i = 0; i < num; i++) {
+ if (tbl[i].in_layout)
+ writel(tbl[i].val, base + regs[tbl[i].offset]);
+ else
+ writel(tbl[i].val, base + tbl[i].offset);
+ }
+}
+
+/*
+ * Update board specific PHY tuning override values if specified from
+ * device tree.
+ */
+static void qusb2_phy_override_phy_params(struct qusb2_phy *qphy)
+{
+ const struct qusb2_phy_cfg *cfg = qphy->cfg;
+
+ if (qphy->override_imp_res_offset)
+ qusb2_write_mask(qphy->base, QUSB2PHY_IMP_CTRL1,
+ qphy->imp_res_offset_value << IMP_RES_OFFSET_SHIFT,
+ IMP_RES_OFFSET_MASK);
+
+ if (qphy->override_hstx_trim)
+ qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
+ qphy->hstx_trim_value << HSTX_TRIM_SHIFT,
+ HSTX_TRIM_MASK);
+
+ if (qphy->override_preemphasis)
+ qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
+ qphy->preemphasis_level << PREEMPHASIS_EN_SHIFT,
+ PREEMPHASIS_EN_MASK);
+
+ if (qphy->override_preemphasis_width) {
+ if (qphy->preemphasis_width ==
+ QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT)
+ qusb2_setbits(qphy->base,
+ cfg->regs[QUSB2PHY_PORT_TUNE1],
+ PREEMPH_WIDTH_HALF_BIT);
+ else
+ qusb2_clrbits(qphy->base,
+ cfg->regs[QUSB2PHY_PORT_TUNE1],
+ PREEMPH_WIDTH_HALF_BIT);
+ }
+}
+
+/*
+ * Fetches HS Tx tuning value from nvmem and sets the
+ * QUSB2PHY_PORT_TUNE1/2 register.
+ * For error case, skip setting the value and use the default value.
+ */
+static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
+{
+ struct device *dev = &qphy->phy->dev;
+ const struct qusb2_phy_cfg *cfg = qphy->cfg;
+ u8 *val;
+
+ /* efuse register is optional */
+ if (!qphy->cell)
+ return;
+
+ /*
+ * Read efuse register having TUNE2/1 parameter's high nibble.
+ * If efuse register shows value as 0x0 (indicating value is not
+ * fused), or if we fail to find a valid efuse register setting,
+ * then use default value for high nibble that we have already
+ * set while configuring the phy.
+ */
+ val = nvmem_cell_read(qphy->cell, NULL);
+ if (IS_ERR(val) || !val[0]) {
+ dev_dbg(dev, "failed to read a valid hs-tx trim value\n");
+ return;
+ }
+
+ /* Fused TUNE1/2 value is the higher nibble only */
+ if (cfg->update_tune1_with_efuse)
+ qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
+ val[0] << HSTX_TRIM_SHIFT,
+ HSTX_TRIM_MASK);
+ else
+ qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE2],
+ val[0] << HSTX_TRIM_SHIFT,
+ HSTX_TRIM_MASK);
+}
+
+static int qusb2_phy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+ struct qusb2_phy *qphy = phy_get_drvdata(phy);
+
+ qphy->mode = mode;
+
+ return 0;
+}
+
+static int __maybe_unused qusb2_phy_runtime_suspend(struct device *dev)
+{
+ struct qusb2_phy *qphy = dev_get_drvdata(dev);
+ const struct qusb2_phy_cfg *cfg = qphy->cfg;
+ u32 intr_mask;
+
+ dev_vdbg(dev, "Suspending QUSB2 Phy, mode:%d\n", qphy->mode);
+
+ if (!qphy->phy_initialized) {
+ dev_vdbg(dev, "PHY not initialized, bailing out\n");
+ return 0;
+ }
+
+ /*
+ * Enable DP/DM interrupts to detect line state changes based on current
+ * speed. In other words, enable the triggers _opposite_ of what the
+ * current D+/D- levels are e.g. if currently D+ high, D- low
+ * (HS 'J'/Suspend), configure the mask to trigger on D+ low OR D- high
+ */
+ intr_mask = DPSE_INTR_EN | DMSE_INTR_EN;
+ switch (qphy->mode) {
+ case PHY_MODE_USB_HOST_HS:
+ case PHY_MODE_USB_HOST_FS:
+ case PHY_MODE_USB_DEVICE_HS:
+ case PHY_MODE_USB_DEVICE_FS:
+ intr_mask |= DMSE_INTR_HIGH_SEL;
+ break;
+ case PHY_MODE_USB_HOST_LS:
+ case PHY_MODE_USB_DEVICE_LS:
+ intr_mask |= DPSE_INTR_HIGH_SEL;
+ break;
+ default:
+ /* No device connected, enable both DP/DM high interrupt */
+ intr_mask |= DMSE_INTR_HIGH_SEL;
+ intr_mask |= DPSE_INTR_HIGH_SEL;
+ break;
+ }
+
+ writel(intr_mask, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]);
+
+ /* hold core PLL into reset */
+ if (cfg->has_pll_override) {
+ qusb2_setbits(qphy->base,
+ cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE],
+ CORE_PLL_EN_FROM_RESET | CORE_RESET |
+ CORE_RESET_MUX);
+ }
+
+ /* enable phy auto-resume only if device is connected on bus */
+ if (qphy->mode != PHY_MODE_INVALID) {
+ qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1],
+ cfg->autoresume_en);
+ /* Autoresume bit has to be toggled in order to enable it */
+ qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1],
+ cfg->autoresume_en);
+ }
+
+ if (!qphy->has_se_clk_scheme)
+ clk_disable_unprepare(qphy->ref_clk);
+
+ clk_disable_unprepare(qphy->cfg_ahb_clk);
+ clk_disable_unprepare(qphy->iface_clk);
+
+ return 0;
+}
+
+static int __maybe_unused qusb2_phy_runtime_resume(struct device *dev)
+{
+ struct qusb2_phy *qphy = dev_get_drvdata(dev);
+ const struct qusb2_phy_cfg *cfg = qphy->cfg;
+ int ret;
+
+ dev_vdbg(dev, "Resuming QUSB2 phy, mode:%d\n", qphy->mode);
+
+ if (!qphy->phy_initialized) {
+ dev_vdbg(dev, "PHY not initialized, bailing out\n");
+ return 0;
+ }
+
+ ret = clk_prepare_enable(qphy->iface_clk);
+ if (ret) {
+ dev_err(dev, "failed to enable iface_clk, %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(qphy->cfg_ahb_clk);
+ if (ret) {
+ dev_err(dev, "failed to enable cfg ahb clock, %d\n", ret);
+ goto disable_iface_clk;
+ }
+
+ if (!qphy->has_se_clk_scheme) {
+ clk_prepare_enable(qphy->ref_clk);
+ if (ret) {
+ dev_err(dev, "failed to enable ref clk, %d\n", ret);
+ goto disable_ahb_clk;
+ }
+ }
+
+ writel(0x0, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]);
+
+ /* bring core PLL out of reset */
+ if (cfg->has_pll_override) {
+ qusb2_clrbits(qphy->base,
+ cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE],
+ CORE_RESET | CORE_RESET_MUX);
+ }
+
+ return 0;
+
+disable_ahb_clk:
+ clk_disable_unprepare(qphy->cfg_ahb_clk);
+disable_iface_clk:
+ clk_disable_unprepare(qphy->iface_clk);
+
+ return ret;
+}
+
+static int qusb2_phy_init(struct phy *phy)
+{
+ struct qusb2_phy *qphy = phy_get_drvdata(phy);
+ const struct qusb2_phy_cfg *cfg = qphy->cfg;
+ unsigned int val = 0;
+ unsigned int clk_scheme;
+ int ret;
+
+ dev_vdbg(&phy->dev, "%s(): Initializing QUSB2 phy\n", __func__);
+
+ /* turn on regulator supplies */
+ ret = regulator_bulk_enable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(qphy->iface_clk);
+ if (ret) {
+ dev_err(&phy->dev, "failed to enable iface_clk, %d\n", ret);
+ goto poweroff_phy;
+ }
+
+ /* enable ahb interface clock to program phy */
+ ret = clk_prepare_enable(qphy->cfg_ahb_clk);
+ if (ret) {
+ dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
+ goto disable_iface_clk;
+ }
+
+ /* Perform phy reset */
+ ret = reset_control_assert(qphy->phy_reset);
+ if (ret) {
+ dev_err(&phy->dev, "failed to assert phy_reset, %d\n", ret);
+ goto disable_ahb_clk;
+ }
+
+ /* 100 us delay to keep PHY in reset mode */
+ usleep_range(100, 150);
+
+ ret = reset_control_deassert(qphy->phy_reset);
+ if (ret) {
+ dev_err(&phy->dev, "failed to de-assert phy_reset, %d\n", ret);
+ goto disable_ahb_clk;
+ }
+
+ /* Disable the PHY */
+ qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN],
+ qphy->cfg->disable_ctrl);
+
+ if (cfg->has_pll_test) {
+ /* save reset value to override reference clock scheme later */
+ val = readl(qphy->base + QUSB2PHY_PLL_TEST);
+ }
+
+ qcom_qusb2_phy_configure(qphy->base, cfg->regs, cfg->tbl,
+ cfg->tbl_num);
+
+ /* Override board specific PHY tuning values */
+ qusb2_phy_override_phy_params(qphy);
+
+ /* Set efuse value for tuning the PHY */
+ qusb2_phy_set_tune2_param(qphy);
+
+ /* Enable the PHY */
+ qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN],
+ POWER_DOWN);
+
+ /* Required to get phy pll lock successfully */
+ usleep_range(150, 160);
+
+ /* Default is single-ended clock on msm8996 */
+ qphy->has_se_clk_scheme = true;
+ /*
+ * read TCSR_PHY_CLK_SCHEME register to check if single-ended
+ * clock scheme is selected. If yes, then disable differential
+ * ref_clk and use single-ended clock, otherwise use differential
+ * ref_clk only.
+ */
+ if (qphy->tcsr) {
+ ret = regmap_read(qphy->tcsr, qphy->cfg->clk_scheme_offset,
+ &clk_scheme);
+ if (ret) {
+ dev_err(&phy->dev, "failed to read clk scheme reg\n");
+ goto assert_phy_reset;
+ }
+
+ /* is it a differential clock scheme ? */
+ if (!(clk_scheme & PHY_CLK_SCHEME_SEL)) {
+ dev_vdbg(&phy->dev, "%s(): select differential clk\n",
+ __func__);
+ qphy->has_se_clk_scheme = false;
+ } else {
+ dev_vdbg(&phy->dev, "%s(): select single-ended clk\n",
+ __func__);
+ }
+ }
+
+ if (!qphy->has_se_clk_scheme) {
+ ret = clk_prepare_enable(qphy->ref_clk);
+ if (ret) {
+ dev_err(&phy->dev, "failed to enable ref clk, %d\n",
+ ret);
+ goto assert_phy_reset;
+ }
+ }
+
+ if (cfg->has_pll_test) {
+ if (!qphy->has_se_clk_scheme)
+ val &= ~CLK_REF_SEL;
+ else
+ val |= CLK_REF_SEL;
+
+ writel(val, qphy->base + QUSB2PHY_PLL_TEST);
+
+ /* ensure above write is through */
+ readl(qphy->base + QUSB2PHY_PLL_TEST);
+ }
+
+ /* Required to get phy pll lock successfully */
+ usleep_range(100, 110);
+
+ val = readb(qphy->base + cfg->regs[QUSB2PHY_PLL_STATUS]);
+ if (!(val & cfg->mask_core_ready)) {
+ dev_err(&phy->dev,
+ "QUSB2PHY pll lock failed: status reg = %x\n", val);
+ ret = -EBUSY;
+ goto disable_ref_clk;
+ }
+ qphy->phy_initialized = true;
+
+ return 0;
+
+disable_ref_clk:
+ if (!qphy->has_se_clk_scheme)
+ clk_disable_unprepare(qphy->ref_clk);
+assert_phy_reset:
+ reset_control_assert(qphy->phy_reset);
+disable_ahb_clk:
+ clk_disable_unprepare(qphy->cfg_ahb_clk);
+disable_iface_clk:
+ clk_disable_unprepare(qphy->iface_clk);
+poweroff_phy:
+ regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+
+ return ret;
+}
+
+static int qusb2_phy_exit(struct phy *phy)
+{
+ struct qusb2_phy *qphy = phy_get_drvdata(phy);
+
+ /* Disable the PHY */
+ qusb2_setbits(qphy->base, qphy->cfg->regs[QUSB2PHY_PORT_POWERDOWN],
+ qphy->cfg->disable_ctrl);
+
+ if (!qphy->has_se_clk_scheme)
+ clk_disable_unprepare(qphy->ref_clk);
+
+ reset_control_assert(qphy->phy_reset);
+
+ clk_disable_unprepare(qphy->cfg_ahb_clk);
+ clk_disable_unprepare(qphy->iface_clk);
+
+ regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+
+ qphy->phy_initialized = false;
+
+ return 0;
+}
+
+static const struct phy_ops qusb2_phy_gen_ops = {
+ .init = qusb2_phy_init,
+ .exit = qusb2_phy_exit,
+ .set_mode = qusb2_phy_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static const struct of_device_id qusb2_phy_of_match_table[] = {
+ {
+ .compatible = "qcom,msm8996-qusb2-phy",
+ .data = &msm8996_phy_cfg,
+ }, {
+ .compatible = "qcom,sdm845-qusb2-phy",
+ .data = &sdm845_phy_cfg,
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qusb2_phy_of_match_table);
+
+static const struct dev_pm_ops qusb2_phy_pm_ops = {
+ SET_RUNTIME_PM_OPS(qusb2_phy_runtime_suspend,
+ qusb2_phy_runtime_resume, NULL)
+};
+
+static int qusb2_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct qusb2_phy *qphy;
+ struct phy_provider *phy_provider;
+ struct phy *generic_phy;
+ struct resource *res;
+ int ret, i;
+ int num;
+ u32 value;
+
+ qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
+ if (!qphy)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ qphy->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(qphy->base))
+ return PTR_ERR(qphy->base);
+
+ qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb");
+ if (IS_ERR(qphy->cfg_ahb_clk)) {
+ ret = PTR_ERR(qphy->cfg_ahb_clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "failed to get cfg ahb clk, %d\n", ret);
+ return ret;
+ }
+
+ qphy->ref_clk = devm_clk_get(dev, "ref");
+ if (IS_ERR(qphy->ref_clk)) {
+ ret = PTR_ERR(qphy->ref_clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "failed to get ref clk, %d\n", ret);
+ return ret;
+ }
+
+ qphy->iface_clk = devm_clk_get(dev, "iface");
+ if (IS_ERR(qphy->iface_clk)) {
+ ret = PTR_ERR(qphy->iface_clk);
+ if (ret == -EPROBE_DEFER)
+ return ret;
+ qphy->iface_clk = NULL;
+ dev_dbg(dev, "failed to get iface clk, %d\n", ret);
+ }
+
+ qphy->phy_reset = devm_reset_control_get_by_index(&pdev->dev, 0);
+ if (IS_ERR(qphy->phy_reset)) {
+ dev_err(dev, "failed to get phy core reset\n");
+ return PTR_ERR(qphy->phy_reset);
+ }
+
+ num = ARRAY_SIZE(qphy->vregs);
+ for (i = 0; i < num; i++)
+ qphy->vregs[i].supply = qusb2_phy_vreg_names[i];
+
+ ret = devm_regulator_bulk_get(dev, num, qphy->vregs);
+ if (ret) {
+ dev_err(dev, "failed to get regulator supplies\n");
+ return ret;
+ }
+
+ /* Get the specific init parameters of QMP phy */
+ qphy->cfg = of_device_get_match_data(dev);
+
+ qphy->tcsr = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "qcom,tcsr-syscon");
+ if (IS_ERR(qphy->tcsr)) {
+ dev_dbg(dev, "failed to lookup TCSR regmap\n");
+ qphy->tcsr = NULL;
+ }
+
+ qphy->cell = devm_nvmem_cell_get(dev, NULL);
+ if (IS_ERR(qphy->cell)) {
+ if (PTR_ERR(qphy->cell) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ qphy->cell = NULL;
+ dev_dbg(dev, "failed to lookup tune2 hstx trim value\n");
+ }
+
+ if (!of_property_read_u32(dev->of_node, "qcom,imp-res-offset-value",
+ &value)) {
+ qphy->imp_res_offset_value = (u8)value;
+ qphy->override_imp_res_offset = true;
+ }
+
+ if (!of_property_read_u32(dev->of_node, "qcom,hstx-trim-value",
+ &value)) {
+ qphy->hstx_trim_value = (u8)value;
+ qphy->override_hstx_trim = true;
+ }
+
+ if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-level",
+ &value)) {
+ qphy->preemphasis_level = (u8)value;
+ qphy->override_preemphasis = true;
+ }
+
+ if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-width",
+ &value)) {
+ qphy->preemphasis_width = (u8)value;
+ qphy->override_preemphasis_width = true;
+ }
+
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+ /*
+ * Prevent runtime pm from being ON by default. Users can enable
+ * it using power/control in sysfs.
+ */
+ pm_runtime_forbid(dev);
+
+ generic_phy = devm_phy_create(dev, NULL, &qusb2_phy_gen_ops);
+ if (IS_ERR(generic_phy)) {
+ ret = PTR_ERR(generic_phy);
+ dev_err(dev, "failed to create phy, %d\n", ret);
+ pm_runtime_disable(dev);
+ return ret;
+ }
+ qphy->phy = generic_phy;
+
+ dev_set_drvdata(dev, qphy);
+ phy_set_drvdata(generic_phy, qphy);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (!IS_ERR(phy_provider))
+ dev_info(dev, "Registered Qcom-QUSB2 phy\n");
+ else
+ pm_runtime_disable(dev);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver qusb2_phy_driver = {
+ .probe = qusb2_phy_probe,
+ .driver = {
+ .name = "qcom-qusb2-phy",
+ .pm = &qusb2_phy_pm_ops,
+ .of_match_table = qusb2_phy_of_match_table,
+ },
+};
+
+module_platform_driver(qusb2_phy_driver);
+
+MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>");
+MODULE_DESCRIPTION("Qualcomm QUSB2 PHY driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-i.h b/drivers/phy/qualcomm/phy-qcom-ufs-i.h
new file mode 100644
index 0000000..822c83b
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-ufs-i.h
@@ -0,0 +1,156 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef UFS_QCOM_PHY_I_H_
+#define UFS_QCOM_PHY_I_H_
+
+#include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <linux/phy/phy-qcom-ufs.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+
+#define readl_poll_timeout(addr, val, cond, sleep_us, timeout_us) \
+({ \
+ ktime_t timeout = ktime_add_us(ktime_get(), timeout_us); \
+ might_sleep_if(timeout_us); \
+ for (;;) { \
+ (val) = readl(addr); \
+ if (cond) \
+ break; \
+ if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) { \
+ (val) = readl(addr); \
+ break; \
+ } \
+ if (sleep_us) \
+ usleep_range(DIV_ROUND_UP(sleep_us, 4), sleep_us); \
+ } \
+ (cond) ? 0 : -ETIMEDOUT; \
+})
+
+#define UFS_QCOM_PHY_CAL_ENTRY(reg, val) \
+ { \
+ .reg_offset = reg, \
+ .cfg_value = val, \
+ }
+
+#define UFS_QCOM_PHY_NAME_LEN 30
+
+enum {
+ MASK_SERDES_START = 0x1,
+ MASK_PCS_READY = 0x1,
+};
+
+enum {
+ OFFSET_SERDES_START = 0x0,
+};
+
+struct ufs_qcom_phy_stored_attributes {
+ u32 att;
+ u32 value;
+};
+
+
+struct ufs_qcom_phy_calibration {
+ u32 reg_offset;
+ u32 cfg_value;
+};
+
+struct ufs_qcom_phy_vreg {
+ const char *name;
+ struct regulator *reg;
+ int max_uA;
+ int min_uV;
+ int max_uV;
+ bool enabled;
+};
+
+struct ufs_qcom_phy {
+ struct list_head list;
+ struct device *dev;
+ void __iomem *mmio;
+ void __iomem *dev_ref_clk_ctrl_mmio;
+ struct clk *tx_iface_clk;
+ struct clk *rx_iface_clk;
+ bool is_iface_clk_enabled;
+ struct clk *ref_clk_src;
+ struct clk *ref_clk_parent;
+ struct clk *ref_clk;
+ bool is_ref_clk_enabled;
+ bool is_dev_ref_clk_enabled;
+ struct ufs_qcom_phy_vreg vdda_pll;
+ struct ufs_qcom_phy_vreg vdda_phy;
+ struct ufs_qcom_phy_vreg vddp_ref_clk;
+ unsigned int quirks;
+
+ /*
+ * If UFS link is put into Hibern8 and if UFS PHY analog hardware is
+ * power collapsed (by clearing UFS_PHY_POWER_DOWN_CONTROL), Hibern8
+ * exit might fail even after powering on UFS PHY analog hardware.
+ * Enabling this quirk will help to solve above issue by doing
+ * custom PHY settings just before PHY analog power collapse.
+ */
+ #define UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE BIT(0)
+
+ u8 host_ctrl_rev_major;
+ u16 host_ctrl_rev_minor;
+ u16 host_ctrl_rev_step;
+
+ char name[UFS_QCOM_PHY_NAME_LEN];
+ struct ufs_qcom_phy_calibration *cached_regs;
+ int cached_regs_table_size;
+ bool is_powered_on;
+ bool is_started;
+ struct ufs_qcom_phy_specific_ops *phy_spec_ops;
+
+ enum phy_mode mode;
+};
+
+/**
+ * struct ufs_qcom_phy_specific_ops - set of pointers to functions which have a
+ * specific implementation per phy. Each UFS phy, should implement
+ * those functions according to its spec and requirements
+ * @start_serdes: pointer to a function that starts the serdes
+ * @is_physical_coding_sublayer_ready: pointer to a function that
+ * checks pcs readiness. returns 0 for success and non-zero for error.
+ * @set_tx_lane_enable: pointer to a function that enable tx lanes
+ * @power_control: pointer to a function that controls analog rail of phy
+ * and writes to QSERDES_RX_SIGDET_CNTRL attribute
+ */
+struct ufs_qcom_phy_specific_ops {
+ void (*start_serdes)(struct ufs_qcom_phy *phy);
+ int (*is_physical_coding_sublayer_ready)(struct ufs_qcom_phy *phy);
+ void (*set_tx_lane_enable)(struct ufs_qcom_phy *phy, u32 val);
+ void (*power_control)(struct ufs_qcom_phy *phy, bool val);
+};
+
+struct ufs_qcom_phy *get_ufs_qcom_phy(struct phy *generic_phy);
+int ufs_qcom_phy_power_on(struct phy *generic_phy);
+int ufs_qcom_phy_power_off(struct phy *generic_phy);
+int ufs_qcom_phy_init_clks(struct ufs_qcom_phy *phy_common);
+int ufs_qcom_phy_init_vregulators(struct ufs_qcom_phy *phy_common);
+int ufs_qcom_phy_remove(struct phy *generic_phy,
+ struct ufs_qcom_phy *ufs_qcom_phy);
+struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev,
+ struct ufs_qcom_phy *common_cfg,
+ const struct phy_ops *ufs_qcom_phy_gen_ops,
+ struct ufs_qcom_phy_specific_ops *phy_spec_ops);
+int ufs_qcom_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy,
+ struct ufs_qcom_phy_calibration *tbl_A, int tbl_size_A,
+ struct ufs_qcom_phy_calibration *tbl_B, int tbl_size_B,
+ bool is_rate_B);
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c
new file mode 100644
index 0000000..ba1895b
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c
@@ -0,0 +1,203 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include "phy-qcom-ufs-qmp-14nm.h"
+
+#define UFS_PHY_NAME "ufs_phy_qmp_14nm"
+#define UFS_PHY_VDDA_PHY_UV (925000)
+
+static
+int ufs_qcom_phy_qmp_14nm_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy,
+ bool is_rate_B)
+{
+ int tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A);
+ int tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B);
+ int err;
+
+ err = ufs_qcom_phy_calibrate(ufs_qcom_phy, phy_cal_table_rate_A,
+ tbl_size_A, phy_cal_table_rate_B, tbl_size_B, is_rate_B);
+
+ if (err)
+ dev_err(ufs_qcom_phy->dev,
+ "%s: ufs_qcom_phy_calibrate() failed %d\n",
+ __func__, err);
+ return err;
+}
+
+static
+void ufs_qcom_phy_qmp_14nm_advertise_quirks(struct ufs_qcom_phy *phy_common)
+{
+ phy_common->quirks =
+ UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE;
+}
+
+static int ufs_qcom_phy_qmp_14nm_init(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy);
+ bool is_rate_B = false;
+ int ret;
+
+ if (phy_common->mode == PHY_MODE_UFS_HS_B)
+ is_rate_B = true;
+
+ ret = ufs_qcom_phy_qmp_14nm_phy_calibrate(phy_common, is_rate_B);
+ if (!ret)
+ /* phy calibrated, but yet to be started */
+ phy_common->is_started = false;
+
+ return ret;
+}
+
+static int ufs_qcom_phy_qmp_14nm_exit(struct phy *generic_phy)
+{
+ return 0;
+}
+
+static
+int ufs_qcom_phy_qmp_14nm_set_mode(struct phy *generic_phy, enum phy_mode mode)
+{
+ struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy);
+
+ phy_common->mode = PHY_MODE_INVALID;
+
+ if (mode > 0)
+ phy_common->mode = mode;
+
+ return 0;
+}
+
+static
+void ufs_qcom_phy_qmp_14nm_power_control(struct ufs_qcom_phy *phy, bool val)
+{
+ writel_relaxed(val ? 0x1 : 0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+ /*
+ * Before any transactions involving PHY, ensure PHY knows
+ * that it's analog rail is powered ON (or OFF).
+ */
+ mb();
+}
+
+static inline
+void ufs_qcom_phy_qmp_14nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val)
+{
+ /*
+ * 14nm PHY does not have TX_LANE_ENABLE register.
+ * Implement this function so as not to propagate error to caller.
+ */
+}
+
+static inline void ufs_qcom_phy_qmp_14nm_start_serdes(struct ufs_qcom_phy *phy)
+{
+ u32 tmp;
+
+ tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START);
+ tmp &= ~MASK_SERDES_START;
+ tmp |= (1 << OFFSET_SERDES_START);
+ writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START);
+ /* Ensure register value is committed */
+ mb();
+}
+
+static int ufs_qcom_phy_qmp_14nm_is_pcs_ready(struct ufs_qcom_phy *phy_common)
+{
+ int err = 0;
+ u32 val;
+
+ err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS,
+ val, (val & MASK_PCS_READY), 10, 1000000);
+ if (err)
+ dev_err(phy_common->dev, "%s: poll for pcs failed err = %d\n",
+ __func__, err);
+ return err;
+}
+
+static const struct phy_ops ufs_qcom_phy_qmp_14nm_phy_ops = {
+ .init = ufs_qcom_phy_qmp_14nm_init,
+ .exit = ufs_qcom_phy_qmp_14nm_exit,
+ .power_on = ufs_qcom_phy_power_on,
+ .power_off = ufs_qcom_phy_power_off,
+ .set_mode = ufs_qcom_phy_qmp_14nm_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static struct ufs_qcom_phy_specific_ops phy_14nm_ops = {
+ .start_serdes = ufs_qcom_phy_qmp_14nm_start_serdes,
+ .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_14nm_is_pcs_ready,
+ .set_tx_lane_enable = ufs_qcom_phy_qmp_14nm_set_tx_lane_enable,
+ .power_control = ufs_qcom_phy_qmp_14nm_power_control,
+};
+
+static int ufs_qcom_phy_qmp_14nm_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy;
+ struct ufs_qcom_phy_qmp_14nm *phy;
+ struct ufs_qcom_phy *phy_common;
+ int err = 0;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy) {
+ err = -ENOMEM;
+ goto out;
+ }
+ phy_common = &phy->common_cfg;
+
+ generic_phy = ufs_qcom_phy_generic_probe(pdev, phy_common,
+ &ufs_qcom_phy_qmp_14nm_phy_ops, &phy_14nm_ops);
+
+ if (!generic_phy) {
+ err = -EIO;
+ goto out;
+ }
+
+ err = ufs_qcom_phy_init_clks(phy_common);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_init_vregulators(phy_common);
+ if (err)
+ goto out;
+
+ phy_common->vdda_phy.max_uV = UFS_PHY_VDDA_PHY_UV;
+ phy_common->vdda_phy.min_uV = UFS_PHY_VDDA_PHY_UV;
+
+ ufs_qcom_phy_qmp_14nm_advertise_quirks(phy_common);
+
+ phy_set_drvdata(generic_phy, phy);
+
+ strlcpy(phy_common->name, UFS_PHY_NAME, sizeof(phy_common->name));
+
+out:
+ return err;
+}
+
+static const struct of_device_id ufs_qcom_phy_qmp_14nm_of_match[] = {
+ {.compatible = "qcom,ufs-phy-qmp-14nm"},
+ {.compatible = "qcom,msm8996-ufs-phy-qmp-14nm"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_14nm_of_match);
+
+static struct platform_driver ufs_qcom_phy_qmp_14nm_driver = {
+ .probe = ufs_qcom_phy_qmp_14nm_probe,
+ .driver = {
+ .of_match_table = ufs_qcom_phy_qmp_14nm_of_match,
+ .name = "ufs_qcom_phy_qmp_14nm",
+ },
+};
+
+module_platform_driver(ufs_qcom_phy_qmp_14nm_driver);
+
+MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 14nm");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h
new file mode 100644
index 0000000..3aefdba
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h
@@ -0,0 +1,177 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef UFS_QCOM_PHY_QMP_14NM_H_
+#define UFS_QCOM_PHY_QMP_14NM_H_
+
+#include "phy-qcom-ufs-i.h"
+
+/* QCOM UFS PHY control registers */
+#define COM_OFF(x) (0x000 + x)
+#define PHY_OFF(x) (0xC00 + x)
+#define TX_OFF(n, x) (0x400 + (0x400 * n) + x)
+#define RX_OFF(n, x) (0x600 + (0x400 * n) + x)
+
+/* UFS PHY QSERDES COM registers */
+#define QSERDES_COM_BG_TIMER COM_OFF(0x0C)
+#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x34)
+#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x3C)
+#define QSERDES_COM_LOCK_CMP1_MODE0 COM_OFF(0x4C)
+#define QSERDES_COM_LOCK_CMP2_MODE0 COM_OFF(0x50)
+#define QSERDES_COM_LOCK_CMP3_MODE0 COM_OFF(0x54)
+#define QSERDES_COM_LOCK_CMP1_MODE1 COM_OFF(0x58)
+#define QSERDES_COM_LOCK_CMP2_MODE1 COM_OFF(0x5C)
+#define QSERDES_COM_LOCK_CMP3_MODE1 COM_OFF(0x60)
+#define QSERDES_COM_CP_CTRL_MODE0 COM_OFF(0x78)
+#define QSERDES_COM_CP_CTRL_MODE1 COM_OFF(0x7C)
+#define QSERDES_COM_PLL_RCTRL_MODE0 COM_OFF(0x84)
+#define QSERDES_COM_PLL_RCTRL_MODE1 COM_OFF(0x88)
+#define QSERDES_COM_PLL_CCTRL_MODE0 COM_OFF(0x90)
+#define QSERDES_COM_PLL_CCTRL_MODE1 COM_OFF(0x94)
+#define QSERDES_COM_SYSCLK_EN_SEL COM_OFF(0xAC)
+#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0xB4)
+#define QSERDES_COM_LOCK_CMP_EN COM_OFF(0xC8)
+#define QSERDES_COM_LOCK_CMP_CFG COM_OFF(0xCC)
+#define QSERDES_COM_DEC_START_MODE0 COM_OFF(0xD0)
+#define QSERDES_COM_DEC_START_MODE1 COM_OFF(0xD4)
+#define QSERDES_COM_DIV_FRAC_START1_MODE0 COM_OFF(0xDC)
+#define QSERDES_COM_DIV_FRAC_START2_MODE0 COM_OFF(0xE0)
+#define QSERDES_COM_DIV_FRAC_START3_MODE0 COM_OFF(0xE4)
+#define QSERDES_COM_DIV_FRAC_START1_MODE1 COM_OFF(0xE8)
+#define QSERDES_COM_DIV_FRAC_START2_MODE1 COM_OFF(0xEC)
+#define QSERDES_COM_DIV_FRAC_START3_MODE1 COM_OFF(0xF0)
+#define QSERDES_COM_INTEGLOOP_GAIN0_MODE0 COM_OFF(0x108)
+#define QSERDES_COM_INTEGLOOP_GAIN1_MODE0 COM_OFF(0x10C)
+#define QSERDES_COM_INTEGLOOP_GAIN0_MODE1 COM_OFF(0x110)
+#define QSERDES_COM_INTEGLOOP_GAIN1_MODE1 COM_OFF(0x114)
+#define QSERDES_COM_VCO_TUNE_CTRL COM_OFF(0x124)
+#define QSERDES_COM_VCO_TUNE_MAP COM_OFF(0x128)
+#define QSERDES_COM_VCO_TUNE1_MODE0 COM_OFF(0x12C)
+#define QSERDES_COM_VCO_TUNE2_MODE0 COM_OFF(0x130)
+#define QSERDES_COM_VCO_TUNE1_MODE1 COM_OFF(0x134)
+#define QSERDES_COM_VCO_TUNE2_MODE1 COM_OFF(0x138)
+#define QSERDES_COM_VCO_TUNE_TIMER1 COM_OFF(0x144)
+#define QSERDES_COM_VCO_TUNE_TIMER2 COM_OFF(0x148)
+#define QSERDES_COM_CLK_SELECT COM_OFF(0x174)
+#define QSERDES_COM_HSCLK_SEL COM_OFF(0x178)
+#define QSERDES_COM_CORECLK_DIV COM_OFF(0x184)
+#define QSERDES_COM_CORE_CLK_EN COM_OFF(0x18C)
+#define QSERDES_COM_CMN_CONFIG COM_OFF(0x194)
+#define QSERDES_COM_SVS_MODE_CLK_SEL COM_OFF(0x19C)
+#define QSERDES_COM_CORECLK_DIV_MODE1 COM_OFF(0x1BC)
+
+/* UFS PHY registers */
+#define UFS_PHY_PHY_START PHY_OFF(0x00)
+#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x04)
+#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x168)
+
+/* UFS PHY TX registers */
+#define QSERDES_TX_HIGHZ_TRANSCEIVER_BIAS_DRVR_EN TX_OFF(0, 0x68)
+#define QSERDES_TX_LANE_MODE TX_OFF(0, 0x94)
+
+/* UFS PHY RX registers */
+#define QSERDES_RX_UCDR_FASTLOCK_FO_GAIN RX_OFF(0, 0x40)
+#define QSERDES_RX_RX_TERM_BW RX_OFF(0, 0x90)
+#define QSERDES_RX_RX_EQ_GAIN1_LSB RX_OFF(0, 0xC4)
+#define QSERDES_RX_RX_EQ_GAIN1_MSB RX_OFF(0, 0xC8)
+#define QSERDES_RX_RX_EQ_GAIN2_LSB RX_OFF(0, 0xCC)
+#define QSERDES_RX_RX_EQ_GAIN2_MSB RX_OFF(0, 0xD0)
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2 RX_OFF(0, 0xD8)
+#define QSERDES_RX_SIGDET_CNTRL RX_OFF(0, 0x114)
+#define QSERDES_RX_SIGDET_LVL RX_OFF(0, 0x118)
+#define QSERDES_RX_SIGDET_DEGLITCH_CNTRL RX_OFF(0, 0x11C)
+#define QSERDES_RX_RX_INTERFACE_MODE RX_OFF(0, 0x12C)
+
+/*
+ * This structure represents the 14nm specific phy.
+ * common_cfg MUST remain the first field in this structure
+ * in case extra fields are added. This way, when calling
+ * get_ufs_qcom_phy() of generic phy, we can extract the
+ * common phy structure (struct ufs_qcom_phy) out of it
+ * regardless of the relevant specific phy.
+ */
+struct ufs_qcom_phy_qmp_14nm {
+ struct ufs_qcom_phy common_cfg;
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_A[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_CONFIG, 0x0e),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL, 0xd7),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CLK_SELECT, 0x30),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYS_CLK_CTRL, 0x06),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BG_TIMER, 0x0a),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_HSCLK_SEL, 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV, 0x0a),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORECLK_DIV_MODE1, 0x0a),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_EN, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_CTRL, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x20),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORE_CLK_EN, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP_CFG, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER1, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_MAP, 0x14),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SVS_MODE_CLK_SEL, 0x05),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE0, 0x82),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE0, 0x0b),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE1_MODE0, 0x28),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE0, 0x02),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE0, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE0, 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE0, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START_MODE1, 0x98),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1_MODE1, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2_MODE1, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3_MODE1, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CP_CTRL_MODE1, 0x0b),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RCTRL_MODE1, 0x16),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CCTRL_MODE1, 0x28),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN0_MODE1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_INTEGLOOP_GAIN1_MODE1, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE1_MODE1, 0xd6),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE2_MODE1, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP1_MODE1, 0x32),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP2_MODE1, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_LOCK_CMP3_MODE1, 0x00),
+
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVER_BIAS_DRVR_EN, 0x45),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE, 0x02),
+
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_LVL, 0x24),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL, 0x02),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_INTERFACE_MODE, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x18),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0B),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_BW, 0x5B),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB, 0xFF),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB, 0x3F),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB, 0xFF),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB, 0x0F),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0E),
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_VCO_TUNE_MAP, 0x54),
+};
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c
new file mode 100644
index 0000000..49f435c
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c
@@ -0,0 +1,257 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include "phy-qcom-ufs-qmp-20nm.h"
+
+#define UFS_PHY_NAME "ufs_phy_qmp_20nm"
+
+static
+int ufs_qcom_phy_qmp_20nm_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy,
+ bool is_rate_B)
+{
+ struct ufs_qcom_phy_calibration *tbl_A, *tbl_B;
+ int tbl_size_A, tbl_size_B;
+ u8 major = ufs_qcom_phy->host_ctrl_rev_major;
+ u16 minor = ufs_qcom_phy->host_ctrl_rev_minor;
+ u16 step = ufs_qcom_phy->host_ctrl_rev_step;
+ int err;
+
+ if ((major == 0x1) && (minor == 0x002) && (step == 0x0000)) {
+ tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_2_0);
+ tbl_A = phy_cal_table_rate_A_1_2_0;
+ } else if ((major == 0x1) && (minor == 0x003) && (step == 0x0000)) {
+ tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_3_0);
+ tbl_A = phy_cal_table_rate_A_1_3_0;
+ } else {
+ dev_err(ufs_qcom_phy->dev, "%s: Unknown UFS-PHY version, no calibration values\n",
+ __func__);
+ err = -ENODEV;
+ goto out;
+ }
+
+ tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B);
+ tbl_B = phy_cal_table_rate_B;
+
+ err = ufs_qcom_phy_calibrate(ufs_qcom_phy, tbl_A, tbl_size_A,
+ tbl_B, tbl_size_B, is_rate_B);
+
+ if (err)
+ dev_err(ufs_qcom_phy->dev, "%s: ufs_qcom_phy_calibrate() failed %d\n",
+ __func__, err);
+
+out:
+ return err;
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_advertise_quirks(struct ufs_qcom_phy *phy_common)
+{
+ phy_common->quirks =
+ UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE;
+}
+
+static int ufs_qcom_phy_qmp_20nm_init(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy);
+ bool is_rate_B = false;
+ int ret;
+
+ if (phy_common->mode == PHY_MODE_UFS_HS_B)
+ is_rate_B = true;
+
+ ret = ufs_qcom_phy_qmp_20nm_phy_calibrate(phy_common, is_rate_B);
+ if (!ret)
+ /* phy calibrated, but yet to be started */
+ phy_common->is_started = false;
+
+ return ret;
+}
+
+static int ufs_qcom_phy_qmp_20nm_exit(struct phy *generic_phy)
+{
+ return 0;
+}
+
+static
+int ufs_qcom_phy_qmp_20nm_set_mode(struct phy *generic_phy, enum phy_mode mode)
+{
+ struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy);
+
+ phy_common->mode = PHY_MODE_INVALID;
+
+ if (mode > 0)
+ phy_common->mode = mode;
+
+ return 0;
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_power_control(struct ufs_qcom_phy *phy, bool val)
+{
+ bool hibern8_exit_after_pwr_collapse = phy->quirks &
+ UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE;
+
+ if (val) {
+ writel_relaxed(0x1, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+ /*
+ * Before any transactions involving PHY, ensure PHY knows
+ * that it's analog rail is powered ON.
+ */
+ mb();
+
+ if (hibern8_exit_after_pwr_collapse) {
+ /*
+ * Give atleast 1us delay after restoring PHY analog
+ * power.
+ */
+ usleep_range(1, 2);
+ writel_relaxed(0x0A, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ writel_relaxed(0x08, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ /*
+ * Make sure workaround is deactivated before proceeding
+ * with normal PHY operations.
+ */
+ mb();
+ }
+ } else {
+ if (hibern8_exit_after_pwr_collapse) {
+ writel_relaxed(0x0A, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ writel_relaxed(0x02, phy->mmio +
+ QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+ /*
+ * Make sure that above workaround is activated before
+ * PHY analog power collapse.
+ */
+ mb();
+ }
+
+ writel_relaxed(0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+ /*
+ * ensure that PHY knows its PHY analog rail is going
+ * to be powered down
+ */
+ mb();
+ }
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val)
+{
+ writel_relaxed(val & UFS_PHY_TX_LANE_ENABLE_MASK,
+ phy->mmio + UFS_PHY_TX_LANE_ENABLE);
+ mb();
+}
+
+static inline void ufs_qcom_phy_qmp_20nm_start_serdes(struct ufs_qcom_phy *phy)
+{
+ u32 tmp;
+
+ tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START);
+ tmp &= ~MASK_SERDES_START;
+ tmp |= (1 << OFFSET_SERDES_START);
+ writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START);
+ mb();
+}
+
+static int ufs_qcom_phy_qmp_20nm_is_pcs_ready(struct ufs_qcom_phy *phy_common)
+{
+ int err = 0;
+ u32 val;
+
+ err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS,
+ val, (val & MASK_PCS_READY), 10, 1000000);
+ if (err)
+ dev_err(phy_common->dev, "%s: poll for pcs failed err = %d\n",
+ __func__, err);
+ return err;
+}
+
+static const struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = {
+ .init = ufs_qcom_phy_qmp_20nm_init,
+ .exit = ufs_qcom_phy_qmp_20nm_exit,
+ .power_on = ufs_qcom_phy_power_on,
+ .power_off = ufs_qcom_phy_power_off,
+ .set_mode = ufs_qcom_phy_qmp_20nm_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static struct ufs_qcom_phy_specific_ops phy_20nm_ops = {
+ .start_serdes = ufs_qcom_phy_qmp_20nm_start_serdes,
+ .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_20nm_is_pcs_ready,
+ .set_tx_lane_enable = ufs_qcom_phy_qmp_20nm_set_tx_lane_enable,
+ .power_control = ufs_qcom_phy_qmp_20nm_power_control,
+};
+
+static int ufs_qcom_phy_qmp_20nm_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy;
+ struct ufs_qcom_phy_qmp_20nm *phy;
+ struct ufs_qcom_phy *phy_common;
+ int err = 0;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy) {
+ err = -ENOMEM;
+ goto out;
+ }
+ phy_common = &phy->common_cfg;
+
+ generic_phy = ufs_qcom_phy_generic_probe(pdev, phy_common,
+ &ufs_qcom_phy_qmp_20nm_phy_ops, &phy_20nm_ops);
+
+ if (!generic_phy) {
+ err = -EIO;
+ goto out;
+ }
+
+ err = ufs_qcom_phy_init_clks(phy_common);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_init_vregulators(phy_common);
+ if (err)
+ goto out;
+
+ ufs_qcom_phy_qmp_20nm_advertise_quirks(phy_common);
+
+ phy_set_drvdata(generic_phy, phy);
+
+ strlcpy(phy_common->name, UFS_PHY_NAME, sizeof(phy_common->name));
+
+out:
+ return err;
+}
+
+static const struct of_device_id ufs_qcom_phy_qmp_20nm_of_match[] = {
+ {.compatible = "qcom,ufs-phy-qmp-20nm"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_20nm_of_match);
+
+static struct platform_driver ufs_qcom_phy_qmp_20nm_driver = {
+ .probe = ufs_qcom_phy_qmp_20nm_probe,
+ .driver = {
+ .of_match_table = ufs_qcom_phy_qmp_20nm_of_match,
+ .name = "ufs_qcom_phy_qmp_20nm",
+ },
+};
+
+module_platform_driver(ufs_qcom_phy_qmp_20nm_driver);
+
+MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 20nm");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h
new file mode 100644
index 0000000..4f3076b
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h
@@ -0,0 +1,235 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef UFS_QCOM_PHY_QMP_20NM_H_
+#define UFS_QCOM_PHY_QMP_20NM_H_
+
+#include "phy-qcom-ufs-i.h"
+
+/* QCOM UFS PHY control registers */
+
+#define COM_OFF(x) (0x000 + x)
+#define PHY_OFF(x) (0xC00 + x)
+#define TX_OFF(n, x) (0x400 + (0x400 * n) + x)
+#define RX_OFF(n, x) (0x600 + (0x400 * n) + x)
+
+/* UFS PHY PLL block registers */
+#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x0)
+#define QSERDES_COM_PLL_VCOTAIL_EN COM_OFF(0x04)
+#define QSERDES_COM_PLL_CNTRL COM_OFF(0x14)
+#define QSERDES_COM_PLL_IP_SETI COM_OFF(0x24)
+#define QSERDES_COM_CORE_CLK_IN_SYNC_SEL COM_OFF(0x28)
+#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x30)
+#define QSERDES_COM_PLL_CP_SETI COM_OFF(0x34)
+#define QSERDES_COM_PLL_IP_SETP COM_OFF(0x38)
+#define QSERDES_COM_PLL_CP_SETP COM_OFF(0x3C)
+#define QSERDES_COM_SYSCLK_EN_SEL_TXBAND COM_OFF(0x48)
+#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0x4C)
+#define QSERDES_COM_RESETSM_CNTRL2 COM_OFF(0x50)
+#define QSERDES_COM_PLLLOCK_CMP1 COM_OFF(0x90)
+#define QSERDES_COM_PLLLOCK_CMP2 COM_OFF(0x94)
+#define QSERDES_COM_PLLLOCK_CMP3 COM_OFF(0x98)
+#define QSERDES_COM_PLLLOCK_CMP_EN COM_OFF(0x9C)
+#define QSERDES_COM_BGTC COM_OFF(0xA0)
+#define QSERDES_COM_DEC_START1 COM_OFF(0xAC)
+#define QSERDES_COM_PLL_AMP_OS COM_OFF(0xB0)
+#define QSERDES_COM_RES_CODE_UP_OFFSET COM_OFF(0xD8)
+#define QSERDES_COM_RES_CODE_DN_OFFSET COM_OFF(0xDC)
+#define QSERDES_COM_DIV_FRAC_START1 COM_OFF(0x100)
+#define QSERDES_COM_DIV_FRAC_START2 COM_OFF(0x104)
+#define QSERDES_COM_DIV_FRAC_START3 COM_OFF(0x108)
+#define QSERDES_COM_DEC_START2 COM_OFF(0x10C)
+#define QSERDES_COM_PLL_RXTXEPCLK_EN COM_OFF(0x110)
+#define QSERDES_COM_PLL_CRCTRL COM_OFF(0x114)
+#define QSERDES_COM_PLL_CLKEPDIV COM_OFF(0x118)
+
+/* TX LANE n (0, 1) registers */
+#define QSERDES_TX_EMP_POST1_LVL(n) TX_OFF(n, 0x08)
+#define QSERDES_TX_DRV_LVL(n) TX_OFF(n, 0x0C)
+#define QSERDES_TX_LANE_MODE(n) TX_OFF(n, 0x54)
+
+/* RX LANE n (0, 1) registers */
+#define QSERDES_RX_CDR_CONTROL1(n) RX_OFF(n, 0x0)
+#define QSERDES_RX_CDR_CONTROL_HALF(n) RX_OFF(n, 0x8)
+#define QSERDES_RX_RX_EQ_GAIN1_LSB(n) RX_OFF(n, 0xA8)
+#define QSERDES_RX_RX_EQ_GAIN1_MSB(n) RX_OFF(n, 0xAC)
+#define QSERDES_RX_RX_EQ_GAIN2_LSB(n) RX_OFF(n, 0xB0)
+#define QSERDES_RX_RX_EQ_GAIN2_MSB(n) RX_OFF(n, 0xB4)
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(n) RX_OFF(n, 0xBC)
+#define QSERDES_RX_CDR_CONTROL_QUARTER(n) RX_OFF(n, 0xC)
+#define QSERDES_RX_SIGDET_CNTRL(n) RX_OFF(n, 0x100)
+
+/* UFS PHY registers */
+#define UFS_PHY_PHY_START PHY_OFF(0x00)
+#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x4)
+#define UFS_PHY_TX_LANE_ENABLE PHY_OFF(0x44)
+#define UFS_PHY_PWM_G1_CLK_DIVIDER PHY_OFF(0x08)
+#define UFS_PHY_PWM_G2_CLK_DIVIDER PHY_OFF(0x0C)
+#define UFS_PHY_PWM_G3_CLK_DIVIDER PHY_OFF(0x10)
+#define UFS_PHY_PWM_G4_CLK_DIVIDER PHY_OFF(0x14)
+#define UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER PHY_OFF(0x34)
+#define UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER PHY_OFF(0x38)
+#define UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER PHY_OFF(0x3C)
+#define UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER PHY_OFF(0x40)
+#define UFS_PHY_OMC_STATUS_RDVAL PHY_OFF(0x68)
+#define UFS_PHY_LINE_RESET_TIME PHY_OFF(0x28)
+#define UFS_PHY_LINE_RESET_GRANULARITY PHY_OFF(0x2C)
+#define UFS_PHY_TSYNC_RSYNC_CNTL PHY_OFF(0x48)
+#define UFS_PHY_PLL_CNTL PHY_OFF(0x50)
+#define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x54)
+#define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x5C)
+#define UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL PHY_OFF(0x58)
+#define UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL PHY_OFF(0x60)
+#define UFS_PHY_CFG_CHANGE_CNT_VAL PHY_OFF(0x64)
+#define UFS_PHY_RX_SYNC_WAIT_TIME PHY_OFF(0x6C)
+#define UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB4)
+#define UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE0)
+#define UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB8)
+#define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE4)
+#define UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xBC)
+#define UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xE8)
+#define UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY PHY_OFF(0xFC)
+#define UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY PHY_OFF(0x100)
+#define UFS_PHY_RX_SIGDET_CTRL3 PHY_OFF(0x14c)
+#define UFS_PHY_RMMI_ATTR_CTRL PHY_OFF(0x160)
+#define UFS_PHY_RMMI_RX_CFGUPDT_L1 (1 << 7)
+#define UFS_PHY_RMMI_TX_CFGUPDT_L1 (1 << 6)
+#define UFS_PHY_RMMI_CFGWR_L1 (1 << 5)
+#define UFS_PHY_RMMI_CFGRD_L1 (1 << 4)
+#define UFS_PHY_RMMI_RX_CFGUPDT_L0 (1 << 3)
+#define UFS_PHY_RMMI_TX_CFGUPDT_L0 (1 << 2)
+#define UFS_PHY_RMMI_CFGWR_L0 (1 << 1)
+#define UFS_PHY_RMMI_CFGRD_L0 (1 << 0)
+#define UFS_PHY_RMMI_ATTRID PHY_OFF(0x164)
+#define UFS_PHY_RMMI_ATTRWRVAL PHY_OFF(0x168)
+#define UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS PHY_OFF(0x16C)
+#define UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS PHY_OFF(0x170)
+#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x174)
+
+#define UFS_PHY_TX_LANE_ENABLE_MASK 0x3
+
+/*
+ * This structure represents the 20nm specific phy.
+ * common_cfg MUST remain the first field in this structure
+ * in case extra fields are added. This way, when calling
+ * get_ufs_qcom_phy() of generic phy, we can extract the
+ * common phy structure (struct ufs_qcom_phy) out of it
+ * regardless of the relevant specific phy.
+ */
+struct ufs_qcom_phy_qmp_20nm {
+ struct ufs_qcom_phy common_cfg;
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_2_0[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x1b),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x0f),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(0), 0x2F),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(0), 0x20),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(1), 0x2F),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(1), 0x20),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3),
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_3_0[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x2b),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x38),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x3c),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_UP_OFFSET, 0x02),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_DN_OFFSET, 0x02),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x40),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3),
+};
+
+static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = {
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x98),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0x65),
+ UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x1e),
+};
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-ufs.c b/drivers/phy/qualcomm/phy-qcom-ufs.c
new file mode 100644
index 0000000..c5493ea
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-ufs.c
@@ -0,0 +1,682 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include "phy-qcom-ufs-i.h"
+
+#define MAX_PROP_NAME 32
+#define VDDA_PHY_MIN_UV 1000000
+#define VDDA_PHY_MAX_UV 1000000
+#define VDDA_PLL_MIN_UV 1800000
+#define VDDA_PLL_MAX_UV 1800000
+#define VDDP_REF_CLK_MIN_UV 1200000
+#define VDDP_REF_CLK_MAX_UV 1200000
+
+int ufs_qcom_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy,
+ struct ufs_qcom_phy_calibration *tbl_A,
+ int tbl_size_A,
+ struct ufs_qcom_phy_calibration *tbl_B,
+ int tbl_size_B, bool is_rate_B)
+{
+ int i;
+ int ret = 0;
+
+ if (!tbl_A) {
+ dev_err(ufs_qcom_phy->dev, "%s: tbl_A is NULL", __func__);
+ ret = EINVAL;
+ goto out;
+ }
+
+ for (i = 0; i < tbl_size_A; i++)
+ writel_relaxed(tbl_A[i].cfg_value,
+ ufs_qcom_phy->mmio + tbl_A[i].reg_offset);
+
+ /*
+ * In case we would like to work in rate B, we need
+ * to override a registers that were configured in rate A table
+ * with registers of rate B table.
+ * table.
+ */
+ if (is_rate_B) {
+ if (!tbl_B) {
+ dev_err(ufs_qcom_phy->dev, "%s: tbl_B is NULL",
+ __func__);
+ ret = EINVAL;
+ goto out;
+ }
+
+ for (i = 0; i < tbl_size_B; i++)
+ writel_relaxed(tbl_B[i].cfg_value,
+ ufs_qcom_phy->mmio + tbl_B[i].reg_offset);
+ }
+
+ /* flush buffered writes */
+ mb();
+
+out:
+ return ret;
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_calibrate);
+
+/*
+ * This assumes the embedded phy structure inside generic_phy is of type
+ * struct ufs_qcom_phy. In order to function properly it's crucial
+ * to keep the embedded struct "struct ufs_qcom_phy common_cfg"
+ * as the first inside generic_phy.
+ */
+struct ufs_qcom_phy *get_ufs_qcom_phy(struct phy *generic_phy)
+{
+ return (struct ufs_qcom_phy *)phy_get_drvdata(generic_phy);
+}
+EXPORT_SYMBOL_GPL(get_ufs_qcom_phy);
+
+static
+int ufs_qcom_phy_base_init(struct platform_device *pdev,
+ struct ufs_qcom_phy *phy_common)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ int err = 0;
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy_mem");
+ phy_common->mmio = devm_ioremap_resource(dev, res);
+ if (IS_ERR((void const *)phy_common->mmio)) {
+ err = PTR_ERR((void const *)phy_common->mmio);
+ phy_common->mmio = NULL;
+ dev_err(dev, "%s: ioremap for phy_mem resource failed %d\n",
+ __func__, err);
+ return err;
+ }
+
+ /* "dev_ref_clk_ctrl_mem" is optional resource */
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+ "dev_ref_clk_ctrl_mem");
+ phy_common->dev_ref_clk_ctrl_mmio = devm_ioremap_resource(dev, res);
+ if (IS_ERR((void const *)phy_common->dev_ref_clk_ctrl_mmio))
+ phy_common->dev_ref_clk_ctrl_mmio = NULL;
+
+ return 0;
+}
+
+struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev,
+ struct ufs_qcom_phy *common_cfg,
+ const struct phy_ops *ufs_qcom_phy_gen_ops,
+ struct ufs_qcom_phy_specific_ops *phy_spec_ops)
+{
+ int err;
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy = NULL;
+ struct phy_provider *phy_provider;
+
+ err = ufs_qcom_phy_base_init(pdev, common_cfg);
+ if (err) {
+ dev_err(dev, "%s: phy base init failed %d\n", __func__, err);
+ goto out;
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider)) {
+ err = PTR_ERR(phy_provider);
+ dev_err(dev, "%s: failed to register phy %d\n", __func__, err);
+ goto out;
+ }
+
+ generic_phy = devm_phy_create(dev, NULL, ufs_qcom_phy_gen_ops);
+ if (IS_ERR(generic_phy)) {
+ err = PTR_ERR(generic_phy);
+ dev_err(dev, "%s: failed to create phy %d\n", __func__, err);
+ generic_phy = NULL;
+ goto out;
+ }
+
+ common_cfg->phy_spec_ops = phy_spec_ops;
+ common_cfg->dev = dev;
+
+out:
+ return generic_phy;
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_generic_probe);
+
+static int __ufs_qcom_phy_clk_get(struct device *dev,
+ const char *name, struct clk **clk_out, bool err_print)
+{
+ struct clk *clk;
+ int err = 0;
+
+ clk = devm_clk_get(dev, name);
+ if (IS_ERR(clk)) {
+ err = PTR_ERR(clk);
+ if (err_print)
+ dev_err(dev, "failed to get %s err %d", name, err);
+ } else {
+ *clk_out = clk;
+ }
+
+ return err;
+}
+
+static int ufs_qcom_phy_clk_get(struct device *dev,
+ const char *name, struct clk **clk_out)
+{
+ return __ufs_qcom_phy_clk_get(dev, name, clk_out, true);
+}
+
+int ufs_qcom_phy_init_clks(struct ufs_qcom_phy *phy_common)
+{
+ int err;
+
+ if (of_device_is_compatible(phy_common->dev->of_node,
+ "qcom,msm8996-ufs-phy-qmp-14nm"))
+ goto skip_txrx_clk;
+
+ err = ufs_qcom_phy_clk_get(phy_common->dev, "tx_iface_clk",
+ &phy_common->tx_iface_clk);
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_clk_get(phy_common->dev, "rx_iface_clk",
+ &phy_common->rx_iface_clk);
+ if (err)
+ goto out;
+
+skip_txrx_clk:
+ err = ufs_qcom_phy_clk_get(phy_common->dev, "ref_clk_src",
+ &phy_common->ref_clk_src);
+ if (err)
+ goto out;
+
+ /*
+ * "ref_clk_parent" is optional hence don't abort init if it's not
+ * found.
+ */
+ __ufs_qcom_phy_clk_get(phy_common->dev, "ref_clk_parent",
+ &phy_common->ref_clk_parent, false);
+
+ err = ufs_qcom_phy_clk_get(phy_common->dev, "ref_clk",
+ &phy_common->ref_clk);
+
+out:
+ return err;
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_init_clks);
+
+static int ufs_qcom_phy_init_vreg(struct device *dev,
+ struct ufs_qcom_phy_vreg *vreg,
+ const char *name)
+{
+ int err = 0;
+
+ char prop_name[MAX_PROP_NAME];
+
+ vreg->name = name;
+ vreg->reg = devm_regulator_get(dev, name);
+ if (IS_ERR(vreg->reg)) {
+ err = PTR_ERR(vreg->reg);
+ dev_err(dev, "failed to get %s, %d\n", name, err);
+ goto out;
+ }
+
+ if (dev->of_node) {
+ snprintf(prop_name, MAX_PROP_NAME, "%s-max-microamp", name);
+ err = of_property_read_u32(dev->of_node,
+ prop_name, &vreg->max_uA);
+ if (err && err != -EINVAL) {
+ dev_err(dev, "%s: failed to read %s\n",
+ __func__, prop_name);
+ goto out;
+ } else if (err == -EINVAL || !vreg->max_uA) {
+ if (regulator_count_voltages(vreg->reg) > 0) {
+ dev_err(dev, "%s: %s is mandatory\n",
+ __func__, prop_name);
+ goto out;
+ }
+ err = 0;
+ }
+ }
+
+ if (!strcmp(name, "vdda-pll")) {
+ vreg->max_uV = VDDA_PLL_MAX_UV;
+ vreg->min_uV = VDDA_PLL_MIN_UV;
+ } else if (!strcmp(name, "vdda-phy")) {
+ vreg->max_uV = VDDA_PHY_MAX_UV;
+ vreg->min_uV = VDDA_PHY_MIN_UV;
+ } else if (!strcmp(name, "vddp-ref-clk")) {
+ vreg->max_uV = VDDP_REF_CLK_MAX_UV;
+ vreg->min_uV = VDDP_REF_CLK_MIN_UV;
+ }
+
+out:
+ return err;
+}
+
+int ufs_qcom_phy_init_vregulators(struct ufs_qcom_phy *phy_common)
+{
+ int err;
+
+ err = ufs_qcom_phy_init_vreg(phy_common->dev, &phy_common->vdda_pll,
+ "vdda-pll");
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_init_vreg(phy_common->dev, &phy_common->vdda_phy,
+ "vdda-phy");
+
+ if (err)
+ goto out;
+
+ err = ufs_qcom_phy_init_vreg(phy_common->dev, &phy_common->vddp_ref_clk,
+ "vddp-ref-clk");
+
+out:
+ return err;
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_init_vregulators);
+
+static int ufs_qcom_phy_cfg_vreg(struct device *dev,
+ struct ufs_qcom_phy_vreg *vreg, bool on)
+{
+ int ret = 0;
+ struct regulator *reg = vreg->reg;
+ const char *name = vreg->name;
+ int min_uV;
+ int uA_load;
+
+ if (regulator_count_voltages(reg) > 0) {
+ min_uV = on ? vreg->min_uV : 0;
+ ret = regulator_set_voltage(reg, min_uV, vreg->max_uV);
+ if (ret) {
+ dev_err(dev, "%s: %s set voltage failed, err=%d\n",
+ __func__, name, ret);
+ goto out;
+ }
+ uA_load = on ? vreg->max_uA : 0;
+ ret = regulator_set_load(reg, uA_load);
+ if (ret >= 0) {
+ /*
+ * regulator_set_load() returns new regulator
+ * mode upon success.
+ */
+ ret = 0;
+ } else {
+ dev_err(dev, "%s: %s set optimum mode(uA_load=%d) failed, err=%d\n",
+ __func__, name, uA_load, ret);
+ goto out;
+ }
+ }
+out:
+ return ret;
+}
+
+static int ufs_qcom_phy_enable_vreg(struct device *dev,
+ struct ufs_qcom_phy_vreg *vreg)
+{
+ int ret = 0;
+
+ if (!vreg || vreg->enabled)
+ goto out;
+
+ ret = ufs_qcom_phy_cfg_vreg(dev, vreg, true);
+ if (ret) {
+ dev_err(dev, "%s: ufs_qcom_phy_cfg_vreg() failed, err=%d\n",
+ __func__, ret);
+ goto out;
+ }
+
+ ret = regulator_enable(vreg->reg);
+ if (ret) {
+ dev_err(dev, "%s: enable failed, err=%d\n",
+ __func__, ret);
+ goto out;
+ }
+
+ vreg->enabled = true;
+out:
+ return ret;
+}
+
+static int ufs_qcom_phy_enable_ref_clk(struct ufs_qcom_phy *phy)
+{
+ int ret = 0;
+
+ if (phy->is_ref_clk_enabled)
+ goto out;
+
+ /*
+ * reference clock is propagated in a daisy-chained manner from
+ * source to phy, so ungate them at each stage.
+ */
+ ret = clk_prepare_enable(phy->ref_clk_src);
+ if (ret) {
+ dev_err(phy->dev, "%s: ref_clk_src enable failed %d\n",
+ __func__, ret);
+ goto out;
+ }
+
+ /*
+ * "ref_clk_parent" is optional clock hence make sure that clk reference
+ * is available before trying to enable the clock.
+ */
+ if (phy->ref_clk_parent) {
+ ret = clk_prepare_enable(phy->ref_clk_parent);
+ if (ret) {
+ dev_err(phy->dev, "%s: ref_clk_parent enable failed %d\n",
+ __func__, ret);
+ goto out_disable_src;
+ }
+ }
+
+ ret = clk_prepare_enable(phy->ref_clk);
+ if (ret) {
+ dev_err(phy->dev, "%s: ref_clk enable failed %d\n",
+ __func__, ret);
+ goto out_disable_parent;
+ }
+
+ phy->is_ref_clk_enabled = true;
+ goto out;
+
+out_disable_parent:
+ if (phy->ref_clk_parent)
+ clk_disable_unprepare(phy->ref_clk_parent);
+out_disable_src:
+ clk_disable_unprepare(phy->ref_clk_src);
+out:
+ return ret;
+}
+
+static int ufs_qcom_phy_disable_vreg(struct device *dev,
+ struct ufs_qcom_phy_vreg *vreg)
+{
+ int ret = 0;
+
+ if (!vreg || !vreg->enabled)
+ goto out;
+
+ ret = regulator_disable(vreg->reg);
+
+ if (!ret) {
+ /* ignore errors on applying disable config */
+ ufs_qcom_phy_cfg_vreg(dev, vreg, false);
+ vreg->enabled = false;
+ } else {
+ dev_err(dev, "%s: %s disable failed, err=%d\n",
+ __func__, vreg->name, ret);
+ }
+out:
+ return ret;
+}
+
+static void ufs_qcom_phy_disable_ref_clk(struct ufs_qcom_phy *phy)
+{
+ if (phy->is_ref_clk_enabled) {
+ clk_disable_unprepare(phy->ref_clk);
+ /*
+ * "ref_clk_parent" is optional clock hence make sure that clk
+ * reference is available before trying to disable the clock.
+ */
+ if (phy->ref_clk_parent)
+ clk_disable_unprepare(phy->ref_clk_parent);
+ clk_disable_unprepare(phy->ref_clk_src);
+ phy->is_ref_clk_enabled = false;
+ }
+}
+
+#define UFS_REF_CLK_EN (1 << 5)
+
+static void ufs_qcom_phy_dev_ref_clk_ctrl(struct phy *generic_phy, bool enable)
+{
+ struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy);
+
+ if (phy->dev_ref_clk_ctrl_mmio &&
+ (enable ^ phy->is_dev_ref_clk_enabled)) {
+ u32 temp = readl_relaxed(phy->dev_ref_clk_ctrl_mmio);
+
+ if (enable)
+ temp |= UFS_REF_CLK_EN;
+ else
+ temp &= ~UFS_REF_CLK_EN;
+
+ /*
+ * If we are here to disable this clock immediately after
+ * entering into hibern8, we need to make sure that device
+ * ref_clk is active atleast 1us after the hibern8 enter.
+ */
+ if (!enable)
+ udelay(1);
+
+ writel_relaxed(temp, phy->dev_ref_clk_ctrl_mmio);
+ /* ensure that ref_clk is enabled/disabled before we return */
+ wmb();
+ /*
+ * If we call hibern8 exit after this, we need to make sure that
+ * device ref_clk is stable for atleast 1us before the hibern8
+ * exit command.
+ */
+ if (enable)
+ udelay(1);
+
+ phy->is_dev_ref_clk_enabled = enable;
+ }
+}
+
+void ufs_qcom_phy_enable_dev_ref_clk(struct phy *generic_phy)
+{
+ ufs_qcom_phy_dev_ref_clk_ctrl(generic_phy, true);
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_enable_dev_ref_clk);
+
+void ufs_qcom_phy_disable_dev_ref_clk(struct phy *generic_phy)
+{
+ ufs_qcom_phy_dev_ref_clk_ctrl(generic_phy, false);
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_disable_dev_ref_clk);
+
+/* Turn ON M-PHY RMMI interface clocks */
+static int ufs_qcom_phy_enable_iface_clk(struct ufs_qcom_phy *phy)
+{
+ int ret = 0;
+
+ if (phy->is_iface_clk_enabled)
+ goto out;
+
+ ret = clk_prepare_enable(phy->tx_iface_clk);
+ if (ret) {
+ dev_err(phy->dev, "%s: tx_iface_clk enable failed %d\n",
+ __func__, ret);
+ goto out;
+ }
+ ret = clk_prepare_enable(phy->rx_iface_clk);
+ if (ret) {
+ clk_disable_unprepare(phy->tx_iface_clk);
+ dev_err(phy->dev, "%s: rx_iface_clk enable failed %d. disabling also tx_iface_clk\n",
+ __func__, ret);
+ goto out;
+ }
+ phy->is_iface_clk_enabled = true;
+
+out:
+ return ret;
+}
+
+/* Turn OFF M-PHY RMMI interface clocks */
+void ufs_qcom_phy_disable_iface_clk(struct ufs_qcom_phy *phy)
+{
+ if (phy->is_iface_clk_enabled) {
+ clk_disable_unprepare(phy->tx_iface_clk);
+ clk_disable_unprepare(phy->rx_iface_clk);
+ phy->is_iface_clk_enabled = false;
+ }
+}
+
+static int ufs_qcom_phy_start_serdes(struct ufs_qcom_phy *ufs_qcom_phy)
+{
+ int ret = 0;
+
+ if (!ufs_qcom_phy->phy_spec_ops->start_serdes) {
+ dev_err(ufs_qcom_phy->dev, "%s: start_serdes() callback is not supported\n",
+ __func__);
+ ret = -ENOTSUPP;
+ } else {
+ ufs_qcom_phy->phy_spec_ops->start_serdes(ufs_qcom_phy);
+ }
+
+ return ret;
+}
+
+int ufs_qcom_phy_set_tx_lane_enable(struct phy *generic_phy, u32 tx_lanes)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+ int ret = 0;
+
+ if (!ufs_qcom_phy->phy_spec_ops->set_tx_lane_enable) {
+ dev_err(ufs_qcom_phy->dev, "%s: set_tx_lane_enable() callback is not supported\n",
+ __func__);
+ ret = -ENOTSUPP;
+ } else {
+ ufs_qcom_phy->phy_spec_ops->set_tx_lane_enable(ufs_qcom_phy,
+ tx_lanes);
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_set_tx_lane_enable);
+
+void ufs_qcom_phy_save_controller_version(struct phy *generic_phy,
+ u8 major, u16 minor, u16 step)
+{
+ struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+
+ ufs_qcom_phy->host_ctrl_rev_major = major;
+ ufs_qcom_phy->host_ctrl_rev_minor = minor;
+ ufs_qcom_phy->host_ctrl_rev_step = step;
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_save_controller_version);
+
+static int ufs_qcom_phy_is_pcs_ready(struct ufs_qcom_phy *ufs_qcom_phy)
+{
+ if (!ufs_qcom_phy->phy_spec_ops->is_physical_coding_sublayer_ready) {
+ dev_err(ufs_qcom_phy->dev, "%s: is_physical_coding_sublayer_ready() callback is not supported\n",
+ __func__);
+ return -ENOTSUPP;
+ }
+
+ return ufs_qcom_phy->phy_spec_ops->
+ is_physical_coding_sublayer_ready(ufs_qcom_phy);
+}
+
+int ufs_qcom_phy_power_on(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy);
+ struct device *dev = phy_common->dev;
+ int err;
+
+ if (phy_common->is_powered_on)
+ return 0;
+
+ if (!phy_common->is_started) {
+ err = ufs_qcom_phy_start_serdes(phy_common);
+ if (err)
+ return err;
+
+ err = ufs_qcom_phy_is_pcs_ready(phy_common);
+ if (err)
+ return err;
+
+ phy_common->is_started = true;
+ }
+
+ err = ufs_qcom_phy_enable_vreg(dev, &phy_common->vdda_phy);
+ if (err) {
+ dev_err(dev, "%s enable vdda_phy failed, err=%d\n",
+ __func__, err);
+ goto out;
+ }
+
+ phy_common->phy_spec_ops->power_control(phy_common, true);
+
+ /* vdda_pll also enables ref clock LDOs so enable it first */
+ err = ufs_qcom_phy_enable_vreg(dev, &phy_common->vdda_pll);
+ if (err) {
+ dev_err(dev, "%s enable vdda_pll failed, err=%d\n",
+ __func__, err);
+ goto out_disable_phy;
+ }
+
+ err = ufs_qcom_phy_enable_iface_clk(phy_common);
+ if (err) {
+ dev_err(dev, "%s enable phy iface clock failed, err=%d\n",
+ __func__, err);
+ goto out_disable_pll;
+ }
+
+ err = ufs_qcom_phy_enable_ref_clk(phy_common);
+ if (err) {
+ dev_err(dev, "%s enable phy ref clock failed, err=%d\n",
+ __func__, err);
+ goto out_disable_iface_clk;
+ }
+
+ /* enable device PHY ref_clk pad rail */
+ if (phy_common->vddp_ref_clk.reg) {
+ err = ufs_qcom_phy_enable_vreg(dev,
+ &phy_common->vddp_ref_clk);
+ if (err) {
+ dev_err(dev, "%s enable vddp_ref_clk failed, err=%d\n",
+ __func__, err);
+ goto out_disable_ref_clk;
+ }
+ }
+
+ phy_common->is_powered_on = true;
+ goto out;
+
+out_disable_ref_clk:
+ ufs_qcom_phy_disable_ref_clk(phy_common);
+out_disable_iface_clk:
+ ufs_qcom_phy_disable_iface_clk(phy_common);
+out_disable_pll:
+ ufs_qcom_phy_disable_vreg(dev, &phy_common->vdda_pll);
+out_disable_phy:
+ ufs_qcom_phy_disable_vreg(dev, &phy_common->vdda_phy);
+out:
+ return err;
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_power_on);
+
+int ufs_qcom_phy_power_off(struct phy *generic_phy)
+{
+ struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy);
+
+ if (!phy_common->is_powered_on)
+ return 0;
+
+ phy_common->phy_spec_ops->power_control(phy_common, false);
+
+ if (phy_common->vddp_ref_clk.reg)
+ ufs_qcom_phy_disable_vreg(phy_common->dev,
+ &phy_common->vddp_ref_clk);
+ ufs_qcom_phy_disable_ref_clk(phy_common);
+ ufs_qcom_phy_disable_iface_clk(phy_common);
+
+ ufs_qcom_phy_disable_vreg(phy_common->dev, &phy_common->vdda_pll);
+ ufs_qcom_phy_disable_vreg(phy_common->dev, &phy_common->vdda_phy);
+ phy_common->is_powered_on = false;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ufs_qcom_phy_power_off);
+
+MODULE_AUTHOR("Yaniv Gardi <ygardi@codeaurora.org>");
+MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>");
+MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/qualcomm/phy-qcom-usb-hs.c b/drivers/phy/qualcomm/phy-qcom-usb-hs.c
new file mode 100644
index 0000000..abbbe75
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-usb-hs.c
@@ -0,0 +1,288 @@
+/**
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/reset.h>
+#include <linux/extcon.h>
+#include <linux/notifier.h>
+
+#define ULPI_PWR_CLK_MNG_REG 0x88
+# define ULPI_PWR_OTG_COMP_DISABLE BIT(0)
+
+#define ULPI_MISC_A 0x96
+# define ULPI_MISC_A_VBUSVLDEXTSEL BIT(1)
+# define ULPI_MISC_A_VBUSVLDEXT BIT(0)
+
+
+struct ulpi_seq {
+ u8 addr;
+ u8 val;
+};
+
+struct qcom_usb_hs_phy {
+ struct ulpi *ulpi;
+ struct phy *phy;
+ struct clk *ref_clk;
+ struct clk *sleep_clk;
+ struct regulator *v1p8;
+ struct regulator *v3p3;
+ struct reset_control *reset;
+ struct ulpi_seq *init_seq;
+ struct extcon_dev *vbus_edev;
+ struct notifier_block vbus_notify;
+};
+
+static int qcom_usb_hs_phy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+ u8 addr;
+ int ret;
+
+ if (!uphy->vbus_edev) {
+ u8 val = 0;
+
+ switch (mode) {
+ case PHY_MODE_USB_OTG:
+ case PHY_MODE_USB_HOST:
+ val |= ULPI_INT_IDGRD;
+ /* fall through */
+ case PHY_MODE_USB_DEVICE:
+ val |= ULPI_INT_SESS_VALID;
+ default:
+ break;
+ }
+
+ ret = ulpi_write(uphy->ulpi, ULPI_USB_INT_EN_RISE, val);
+ if (ret)
+ return ret;
+ ret = ulpi_write(uphy->ulpi, ULPI_USB_INT_EN_FALL, val);
+ } else {
+ switch (mode) {
+ case PHY_MODE_USB_OTG:
+ case PHY_MODE_USB_DEVICE:
+ addr = ULPI_SET(ULPI_MISC_A);
+ break;
+ case PHY_MODE_USB_HOST:
+ addr = ULPI_CLR(ULPI_MISC_A);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ret = ulpi_write(uphy->ulpi, ULPI_SET(ULPI_PWR_CLK_MNG_REG),
+ ULPI_PWR_OTG_COMP_DISABLE);
+ if (ret)
+ return ret;
+ ret = ulpi_write(uphy->ulpi, addr, ULPI_MISC_A_VBUSVLDEXTSEL);
+ }
+
+ return ret;
+}
+
+static int
+qcom_usb_hs_phy_vbus_notifier(struct notifier_block *nb, unsigned long event,
+ void *ptr)
+{
+ struct qcom_usb_hs_phy *uphy;
+ u8 addr;
+
+ uphy = container_of(nb, struct qcom_usb_hs_phy, vbus_notify);
+
+ if (event)
+ addr = ULPI_SET(ULPI_MISC_A);
+ else
+ addr = ULPI_CLR(ULPI_MISC_A);
+
+ return ulpi_write(uphy->ulpi, addr, ULPI_MISC_A_VBUSVLDEXT);
+}
+
+static int qcom_usb_hs_phy_power_on(struct phy *phy)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+ struct ulpi *ulpi = uphy->ulpi;
+ const struct ulpi_seq *seq;
+ int ret, state;
+
+ ret = clk_prepare_enable(uphy->ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(uphy->sleep_clk);
+ if (ret)
+ goto err_sleep;
+
+ ret = regulator_set_load(uphy->v1p8, 50000);
+ if (ret < 0)
+ goto err_1p8;
+
+ ret = regulator_enable(uphy->v1p8);
+ if (ret)
+ goto err_1p8;
+
+ ret = regulator_set_voltage_triplet(uphy->v3p3, 3050000, 3300000,
+ 3300000);
+ if (ret)
+ goto err_3p3;
+
+ ret = regulator_set_load(uphy->v3p3, 50000);
+ if (ret < 0)
+ goto err_3p3;
+
+ ret = regulator_enable(uphy->v3p3);
+ if (ret)
+ goto err_3p3;
+
+ for (seq = uphy->init_seq; seq->addr; seq++) {
+ ret = ulpi_write(ulpi, ULPI_EXT_VENDOR_SPECIFIC + seq->addr,
+ seq->val);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->reset) {
+ ret = reset_control_reset(uphy->reset);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->vbus_edev) {
+ state = extcon_get_state(uphy->vbus_edev, EXTCON_USB);
+ /* setup initial state */
+ qcom_usb_hs_phy_vbus_notifier(&uphy->vbus_notify, state,
+ uphy->vbus_edev);
+ ret = devm_extcon_register_notifier(&ulpi->dev, uphy->vbus_edev,
+ EXTCON_USB, &uphy->vbus_notify);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ return 0;
+err_ulpi:
+ regulator_disable(uphy->v3p3);
+err_3p3:
+ regulator_disable(uphy->v1p8);
+err_1p8:
+ clk_disable_unprepare(uphy->sleep_clk);
+err_sleep:
+ clk_disable_unprepare(uphy->ref_clk);
+ return ret;
+}
+
+static int qcom_usb_hs_phy_power_off(struct phy *phy)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+
+ regulator_disable(uphy->v3p3);
+ regulator_disable(uphy->v1p8);
+ clk_disable_unprepare(uphy->sleep_clk);
+ clk_disable_unprepare(uphy->ref_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_usb_hs_phy_ops = {
+ .power_on = qcom_usb_hs_phy_power_on,
+ .power_off = qcom_usb_hs_phy_power_off,
+ .set_mode = qcom_usb_hs_phy_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_usb_hs_phy_probe(struct ulpi *ulpi)
+{
+ struct qcom_usb_hs_phy *uphy;
+ struct phy_provider *p;
+ struct clk *clk;
+ struct regulator *reg;
+ struct reset_control *reset;
+ int size;
+ int ret;
+
+ uphy = devm_kzalloc(&ulpi->dev, sizeof(*uphy), GFP_KERNEL);
+ if (!uphy)
+ return -ENOMEM;
+ ulpi_set_drvdata(ulpi, uphy);
+ uphy->ulpi = ulpi;
+
+ size = of_property_count_u8_elems(ulpi->dev.of_node, "qcom,init-seq");
+ if (size < 0)
+ size = 0;
+ uphy->init_seq = devm_kmalloc_array(&ulpi->dev, (size / 2) + 1,
+ sizeof(*uphy->init_seq), GFP_KERNEL);
+ if (!uphy->init_seq)
+ return -ENOMEM;
+ ret = of_property_read_u8_array(ulpi->dev.of_node, "qcom,init-seq",
+ (u8 *)uphy->init_seq, size);
+ if (ret && size)
+ return ret;
+ /* NUL terminate */
+ uphy->init_seq[size / 2].addr = uphy->init_seq[size / 2].val = 0;
+
+ uphy->ref_clk = clk = devm_clk_get(&ulpi->dev, "ref");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->sleep_clk = clk = devm_clk_get(&ulpi->dev, "sleep");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->v1p8 = reg = devm_regulator_get(&ulpi->dev, "v1p8");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->v3p3 = reg = devm_regulator_get(&ulpi->dev, "v3p3");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->reset = reset = devm_reset_control_get(&ulpi->dev, "por");
+ if (IS_ERR(reset)) {
+ if (PTR_ERR(reset) == -EPROBE_DEFER)
+ return PTR_ERR(reset);
+ uphy->reset = NULL;
+ }
+
+ uphy->phy = devm_phy_create(&ulpi->dev, ulpi->dev.of_node,
+ &qcom_usb_hs_phy_ops);
+ if (IS_ERR(uphy->phy))
+ return PTR_ERR(uphy->phy);
+
+ uphy->vbus_edev = extcon_get_edev_by_phandle(&ulpi->dev, 0);
+ if (IS_ERR(uphy->vbus_edev)) {
+ if (PTR_ERR(uphy->vbus_edev) != -ENODEV)
+ return PTR_ERR(uphy->vbus_edev);
+ uphy->vbus_edev = NULL;
+ }
+
+ uphy->vbus_notify.notifier_call = qcom_usb_hs_phy_vbus_notifier;
+ phy_set_drvdata(uphy->phy, uphy);
+
+ p = devm_of_phy_provider_register(&ulpi->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(p);
+}
+
+static const struct of_device_id qcom_usb_hs_phy_match[] = {
+ { .compatible = "qcom,usb-hs-phy", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_hs_phy_match);
+
+static struct ulpi_driver qcom_usb_hs_phy_driver = {
+ .probe = qcom_usb_hs_phy_probe,
+ .driver = {
+ .name = "qcom_usb_hs_phy",
+ .of_match_table = qcom_usb_hs_phy_match,
+ },
+};
+module_ulpi_driver(qcom_usb_hs_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB HS phy");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/qualcomm/phy-qcom-usb-hsic.c b/drivers/phy/qualcomm/phy-qcom-usb-hsic.c
new file mode 100644
index 0000000..c110563
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-usb-hsic.c
@@ -0,0 +1,159 @@
+/**
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/phy/phy.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinctrl-state.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+
+#define ULPI_HSIC_CFG 0x30
+#define ULPI_HSIC_IO_CAL 0x33
+
+struct qcom_usb_hsic_phy {
+ struct ulpi *ulpi;
+ struct phy *phy;
+ struct pinctrl *pctl;
+ struct clk *phy_clk;
+ struct clk *cal_clk;
+ struct clk *cal_sleep_clk;
+};
+
+static int qcom_usb_hsic_phy_power_on(struct phy *phy)
+{
+ struct qcom_usb_hsic_phy *uphy = phy_get_drvdata(phy);
+ struct ulpi *ulpi = uphy->ulpi;
+ struct pinctrl_state *pins_default;
+ int ret;
+
+ ret = clk_prepare_enable(uphy->phy_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(uphy->cal_clk);
+ if (ret)
+ goto err_cal;
+
+ ret = clk_prepare_enable(uphy->cal_sleep_clk);
+ if (ret)
+ goto err_sleep;
+
+ /* Set periodic calibration interval to ~2.048sec in HSIC_IO_CAL_REG */
+ ret = ulpi_write(ulpi, ULPI_HSIC_IO_CAL, 0xff);
+ if (ret)
+ goto err_ulpi;
+
+ /* Enable periodic IO calibration in HSIC_CFG register */
+ ret = ulpi_write(ulpi, ULPI_HSIC_CFG, 0xa8);
+ if (ret)
+ goto err_ulpi;
+
+ /* Configure pins for HSIC functionality */
+ pins_default = pinctrl_lookup_state(uphy->pctl, PINCTRL_STATE_DEFAULT);
+ if (IS_ERR(pins_default))
+ return PTR_ERR(pins_default);
+
+ ret = pinctrl_select_state(uphy->pctl, pins_default);
+ if (ret)
+ goto err_ulpi;
+
+ /* Enable HSIC mode in HSIC_CFG register */
+ ret = ulpi_write(ulpi, ULPI_SET(ULPI_HSIC_CFG), 0x01);
+ if (ret)
+ goto err_ulpi;
+
+ /* Disable auto-resume */
+ ret = ulpi_write(ulpi, ULPI_CLR(ULPI_IFC_CTRL),
+ ULPI_IFC_CTRL_AUTORESUME);
+ if (ret)
+ goto err_ulpi;
+
+ return ret;
+err_ulpi:
+ clk_disable_unprepare(uphy->cal_sleep_clk);
+err_sleep:
+ clk_disable_unprepare(uphy->cal_clk);
+err_cal:
+ clk_disable_unprepare(uphy->phy_clk);
+ return ret;
+}
+
+static int qcom_usb_hsic_phy_power_off(struct phy *phy)
+{
+ struct qcom_usb_hsic_phy *uphy = phy_get_drvdata(phy);
+
+ clk_disable_unprepare(uphy->cal_sleep_clk);
+ clk_disable_unprepare(uphy->cal_clk);
+ clk_disable_unprepare(uphy->phy_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_usb_hsic_phy_ops = {
+ .power_on = qcom_usb_hsic_phy_power_on,
+ .power_off = qcom_usb_hsic_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_usb_hsic_phy_probe(struct ulpi *ulpi)
+{
+ struct qcom_usb_hsic_phy *uphy;
+ struct phy_provider *p;
+ struct clk *clk;
+
+ uphy = devm_kzalloc(&ulpi->dev, sizeof(*uphy), GFP_KERNEL);
+ if (!uphy)
+ return -ENOMEM;
+ ulpi_set_drvdata(ulpi, uphy);
+
+ uphy->ulpi = ulpi;
+ uphy->pctl = devm_pinctrl_get(&ulpi->dev);
+ if (IS_ERR(uphy->pctl))
+ return PTR_ERR(uphy->pctl);
+
+ uphy->phy_clk = clk = devm_clk_get(&ulpi->dev, "phy");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->cal_clk = clk = devm_clk_get(&ulpi->dev, "cal");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->cal_sleep_clk = clk = devm_clk_get(&ulpi->dev, "cal_sleep");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->phy = devm_phy_create(&ulpi->dev, ulpi->dev.of_node,
+ &qcom_usb_hsic_phy_ops);
+ if (IS_ERR(uphy->phy))
+ return PTR_ERR(uphy->phy);
+ phy_set_drvdata(uphy->phy, uphy);
+
+ p = devm_of_phy_provider_register(&ulpi->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(p);
+}
+
+static const struct of_device_id qcom_usb_hsic_phy_match[] = {
+ { .compatible = "qcom,usb-hsic-phy", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_hsic_phy_match);
+
+static struct ulpi_driver qcom_usb_hsic_phy_driver = {
+ .probe = qcom_usb_hsic_phy_probe,
+ .driver = {
+ .name = "qcom_usb_hsic_phy",
+ .of_match_table = qcom_usb_hsic_phy_match,
+ },
+};
+module_ulpi_driver(qcom_usb_hsic_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB HSIC phy");
+MODULE_LICENSE("GPL v2");