v4.19.13 snapshot.
diff --git a/drivers/net/ethernet/freescale/Kconfig b/drivers/net/ethernet/freescale/Kconfig
new file mode 100644
index 0000000..a580a3d
--- /dev/null
+++ b/drivers/net/ethernet/freescale/Kconfig
@@ -0,0 +1,100 @@
+#
+# Freescale device configuration
+#
+
+config NET_VENDOR_FREESCALE
+ bool "Freescale devices"
+ default y
+ depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
+ M523x || M527x || M5272 || M528x || M520x || M532x || \
+ ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
+ ARCH_LAYERSCAPE || COMPILE_TEST
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Freescale devices. If you say Y, you will be
+ asked for your specific card in the following questions.
+
+if NET_VENDOR_FREESCALE
+
+config FEC
+ tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
+ depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
+ ARCH_MXC || SOC_IMX28 || COMPILE_TEST)
+ default ARCH_MXC || SOC_IMX28 if ARM
+ select PHYLIB
+ imply PTP_1588_CLOCK
+ ---help---
+ Say Y here if you want to use the built-in 10/100 Fast ethernet
+ controller on some Motorola ColdFire and Freescale i.MX processors.
+
+config FEC_MPC52xx
+ tristate "FEC MPC52xx driver"
+ depends on PPC_MPC52xx && PPC_BESTCOMM
+ select CRC32
+ select PHYLIB
+ select PPC_BESTCOMM_FEC
+ ---help---
+ This option enables support for the MPC5200's on-chip
+ Fast Ethernet Controller
+ If compiled as module, it will be called fec_mpc52xx.
+
+config FEC_MPC52xx_MDIO
+ bool "FEC MPC52xx MDIO bus driver"
+ depends on FEC_MPC52xx
+ default y
+ ---help---
+ The MPC5200's FEC can connect to the Ethernet either with
+ an external MII PHY chip or 10 Mbps 7-wire interface
+ (Motorola? industry standard).
+ If your board uses an external PHY connected to FEC, enable this.
+ If not sure, enable.
+ If compiled as module, it will be called fec_mpc52xx_phy.
+
+source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
+source "drivers/net/ethernet/freescale/fman/Kconfig"
+
+config FSL_PQ_MDIO
+ tristate "Freescale PQ MDIO"
+ select PHYLIB
+ ---help---
+ This driver supports the MDIO bus used by the gianfar and UCC drivers.
+
+config FSL_XGMAC_MDIO
+ tristate "Freescale XGMAC MDIO"
+ select PHYLIB
+ depends on OF
+ select OF_MDIO
+ ---help---
+ This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
+ on the FMan mEMAC (which supports both Clauses 22 and 45)
+
+config UCC_GETH
+ tristate "Freescale QE Gigabit Ethernet"
+ depends on QUICC_ENGINE
+ select FSL_PQ_MDIO
+ select PHYLIB
+ ---help---
+ This driver supports the Gigabit Ethernet mode of the QUICC Engine,
+ which is available on some Freescale SOCs.
+
+config UGETH_TX_ON_DEMAND
+ bool "Transmit on Demand support"
+ depends on UCC_GETH
+
+config GIANFAR
+ tristate "Gianfar Ethernet"
+ depends on HAS_DMA
+ select FSL_PQ_MDIO
+ select PHYLIB
+ select CRC32
+ ---help---
+ This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
+ and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
+ on the 8540.
+
+source "drivers/net/ethernet/freescale/dpaa/Kconfig"
+
+endif # NET_VENDOR_FREESCALE