v4.19.13 snapshot.
diff --git a/drivers/media/pci/cx18/cx18-firmware.c b/drivers/media/pci/cx18/cx18-firmware.c
new file mode 100644
index 0000000..498a185
--- /dev/null
+++ b/drivers/media/pci/cx18/cx18-firmware.c
@@ -0,0 +1,454 @@
+/*
+ * cx18 firmware functions
+ *
+ * Copyright (C) 2007 Hans Verkuil <hverkuil@xs4all.nl>
+ * Copyright (C) 2008 Andy Walls <awalls@md.metrocast.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include "cx18-driver.h"
+#include "cx18-io.h"
+#include "cx18-scb.h"
+#include "cx18-irq.h"
+#include "cx18-firmware.h"
+#include "cx18-cards.h"
+#include <linux/firmware.h>
+
+#define CX18_PROC_SOFT_RESET 0xc70010
+#define CX18_DDR_SOFT_RESET 0xc70014
+#define CX18_CLOCK_SELECT1 0xc71000
+#define CX18_CLOCK_SELECT2 0xc71004
+#define CX18_HALF_CLOCK_SELECT1 0xc71008
+#define CX18_HALF_CLOCK_SELECT2 0xc7100C
+#define CX18_CLOCK_POLARITY1 0xc71010
+#define CX18_CLOCK_POLARITY2 0xc71014
+#define CX18_ADD_DELAY_ENABLE1 0xc71018
+#define CX18_ADD_DELAY_ENABLE2 0xc7101C
+#define CX18_CLOCK_ENABLE1 0xc71020
+#define CX18_CLOCK_ENABLE2 0xc71024
+
+#define CX18_REG_BUS_TIMEOUT_EN 0xc72024
+
+#define CX18_FAST_CLOCK_PLL_INT 0xc78000
+#define CX18_FAST_CLOCK_PLL_FRAC 0xc78004
+#define CX18_FAST_CLOCK_PLL_POST 0xc78008
+#define CX18_FAST_CLOCK_PLL_PRESCALE 0xc7800C
+#define CX18_FAST_CLOCK_PLL_ADJUST_BANDWIDTH 0xc78010
+
+#define CX18_SLOW_CLOCK_PLL_INT 0xc78014
+#define CX18_SLOW_CLOCK_PLL_FRAC 0xc78018
+#define CX18_SLOW_CLOCK_PLL_POST 0xc7801C
+#define CX18_MPEG_CLOCK_PLL_INT 0xc78040
+#define CX18_MPEG_CLOCK_PLL_FRAC 0xc78044
+#define CX18_MPEG_CLOCK_PLL_POST 0xc78048
+#define CX18_PLL_POWER_DOWN 0xc78088
+#define CX18_SW1_INT_STATUS 0xc73104
+#define CX18_SW1_INT_ENABLE_PCI 0xc7311C
+#define CX18_SW2_INT_SET 0xc73140
+#define CX18_SW2_INT_STATUS 0xc73144
+#define CX18_ADEC_CONTROL 0xc78120
+
+#define CX18_DDR_REQUEST_ENABLE 0xc80000
+#define CX18_DDR_CHIP_CONFIG 0xc80004
+#define CX18_DDR_REFRESH 0xc80008
+#define CX18_DDR_TIMING1 0xc8000C
+#define CX18_DDR_TIMING2 0xc80010
+#define CX18_DDR_POWER_REG 0xc8001C
+
+#define CX18_DDR_TUNE_LANE 0xc80048
+#define CX18_DDR_INITIAL_EMRS 0xc80054
+#define CX18_DDR_MB_PER_ROW_7 0xc8009C
+#define CX18_DDR_BASE_63_ADDR 0xc804FC
+
+#define CX18_WMB_CLIENT02 0xc90108
+#define CX18_WMB_CLIENT05 0xc90114
+#define CX18_WMB_CLIENT06 0xc90118
+#define CX18_WMB_CLIENT07 0xc9011C
+#define CX18_WMB_CLIENT08 0xc90120
+#define CX18_WMB_CLIENT09 0xc90124
+#define CX18_WMB_CLIENT10 0xc90128
+#define CX18_WMB_CLIENT11 0xc9012C
+#define CX18_WMB_CLIENT12 0xc90130
+#define CX18_WMB_CLIENT13 0xc90134
+#define CX18_WMB_CLIENT14 0xc90138
+
+#define CX18_DSP0_INTERRUPT_MASK 0xd0004C
+
+#define APU_ROM_SYNC1 0x6D676553 /* "mgeS" */
+#define APU_ROM_SYNC2 0x72646548 /* "rdeH" */
+
+struct cx18_apu_rom_seghdr {
+ u32 sync1;
+ u32 sync2;
+ u32 addr;
+ u32 size;
+};
+
+static int load_cpu_fw_direct(const char *fn, u8 __iomem *mem, struct cx18 *cx)
+{
+ const struct firmware *fw = NULL;
+ int i, j;
+ unsigned size;
+ u32 __iomem *dst = (u32 __iomem *)mem;
+ const u32 *src;
+
+ if (request_firmware(&fw, fn, &cx->pci_dev->dev)) {
+ CX18_ERR("Unable to open firmware %s\n", fn);
+ CX18_ERR("Did you put the firmware in the hotplug firmware directory?\n");
+ return -ENOMEM;
+ }
+
+ src = (const u32 *)fw->data;
+
+ for (i = 0; i < fw->size; i += 4096) {
+ cx18_setup_page(cx, i);
+ for (j = i; j < fw->size && j < i + 4096; j += 4) {
+ /* no need for endianness conversion on the ppc */
+ cx18_raw_writel(cx, *src, dst);
+ if (cx18_raw_readl(cx, dst) != *src) {
+ CX18_ERR("Mismatch at offset %x\n", i);
+ release_firmware(fw);
+ cx18_setup_page(cx, 0);
+ return -EIO;
+ }
+ dst++;
+ src++;
+ }
+ }
+ if (!test_bit(CX18_F_I_LOADED_FW, &cx->i_flags))
+ CX18_INFO("loaded %s firmware (%zu bytes)\n", fn, fw->size);
+ size = fw->size;
+ release_firmware(fw);
+ cx18_setup_page(cx, SCB_OFFSET);
+ return size;
+}
+
+static int load_apu_fw_direct(const char *fn, u8 __iomem *dst, struct cx18 *cx,
+ u32 *entry_addr)
+{
+ const struct firmware *fw = NULL;
+ int i, j;
+ unsigned size;
+ const u32 *src;
+ struct cx18_apu_rom_seghdr seghdr;
+ const u8 *vers;
+ u32 offset = 0;
+ u32 apu_version = 0;
+ int sz;
+
+ if (request_firmware(&fw, fn, &cx->pci_dev->dev)) {
+ CX18_ERR("unable to open firmware %s\n", fn);
+ CX18_ERR("did you put the firmware in the hotplug firmware directory?\n");
+ cx18_setup_page(cx, 0);
+ return -ENOMEM;
+ }
+
+ *entry_addr = 0;
+ src = (const u32 *)fw->data;
+ vers = fw->data + sizeof(seghdr);
+ sz = fw->size;
+
+ apu_version = (vers[0] << 24) | (vers[4] << 16) | vers[32];
+ while (offset + sizeof(seghdr) < fw->size) {
+ const __le32 *shptr = (__force __le32 *)src + offset / 4;
+
+ seghdr.sync1 = le32_to_cpu(shptr[0]);
+ seghdr.sync2 = le32_to_cpu(shptr[1]);
+ seghdr.addr = le32_to_cpu(shptr[2]);
+ seghdr.size = le32_to_cpu(shptr[3]);
+
+ offset += sizeof(seghdr);
+ if (seghdr.sync1 != APU_ROM_SYNC1 ||
+ seghdr.sync2 != APU_ROM_SYNC2) {
+ offset += seghdr.size;
+ continue;
+ }
+ CX18_DEBUG_INFO("load segment %x-%x\n", seghdr.addr,
+ seghdr.addr + seghdr.size - 1);
+ if (*entry_addr == 0)
+ *entry_addr = seghdr.addr;
+ if (offset + seghdr.size > sz)
+ break;
+ for (i = 0; i < seghdr.size; i += 4096) {
+ cx18_setup_page(cx, seghdr.addr + i);
+ for (j = i; j < seghdr.size && j < i + 4096; j += 4) {
+ /* no need for endianness conversion on the ppc */
+ cx18_raw_writel(cx, src[(offset + j) / 4],
+ dst + seghdr.addr + j);
+ if (cx18_raw_readl(cx, dst + seghdr.addr + j)
+ != src[(offset + j) / 4]) {
+ CX18_ERR("Mismatch at offset %x\n",
+ offset + j);
+ release_firmware(fw);
+ cx18_setup_page(cx, 0);
+ return -EIO;
+ }
+ }
+ }
+ offset += seghdr.size;
+ }
+ if (!test_bit(CX18_F_I_LOADED_FW, &cx->i_flags))
+ CX18_INFO("loaded %s firmware V%08x (%zu bytes)\n",
+ fn, apu_version, fw->size);
+ size = fw->size;
+ release_firmware(fw);
+ cx18_setup_page(cx, 0);
+ return size;
+}
+
+void cx18_halt_firmware(struct cx18 *cx)
+{
+ CX18_DEBUG_INFO("Preparing for firmware halt.\n");
+ cx18_write_reg_expect(cx, 0x000F000F, CX18_PROC_SOFT_RESET,
+ 0x0000000F, 0x000F000F);
+ cx18_write_reg_expect(cx, 0x00020002, CX18_ADEC_CONTROL,
+ 0x00000002, 0x00020002);
+}
+
+void cx18_init_power(struct cx18 *cx, int lowpwr)
+{
+ /* power-down Spare and AOM PLLs */
+ /* power-up fast, slow and mpeg PLLs */
+ cx18_write_reg(cx, 0x00000008, CX18_PLL_POWER_DOWN);
+
+ /* ADEC out of sleep */
+ cx18_write_reg_expect(cx, 0x00020000, CX18_ADEC_CONTROL,
+ 0x00000000, 0x00020002);
+
+ /*
+ * The PLL parameters are based on the external crystal frequency that
+ * would ideally be:
+ *
+ * NTSC Color subcarrier freq * 8 =
+ * 4.5 MHz/286 * 455/2 * 8 = 28.63636363... MHz
+ *
+ * The accidents of history and rationale that explain from where this
+ * combination of magic numbers originate can be found in:
+ *
+ * [1] Abrahams, I. C., "Choice of Chrominance Subcarrier Frequency in
+ * the NTSC Standards", Proceedings of the I-R-E, January 1954, pp 79-80
+ *
+ * [2] Abrahams, I. C., "The 'Frequency Interleaving' Principle in the
+ * NTSC Standards", Proceedings of the I-R-E, January 1954, pp 81-83
+ *
+ * As Mike Bradley has rightly pointed out, it's not the exact crystal
+ * frequency that matters, only that all parts of the driver and
+ * firmware are using the same value (close to the ideal value).
+ *
+ * Since I have a strong suspicion that, if the firmware ever assumes a
+ * crystal value at all, it will assume 28.636360 MHz, the crystal
+ * freq used in calculations in this driver will be:
+ *
+ * xtal_freq = 28.636360 MHz
+ *
+ * an error of less than 0.13 ppm which is way, way better than any off
+ * the shelf crystal will have for accuracy anyway.
+ *
+ * Below I aim to run the PLLs' VCOs near 400 MHz to minimze errors.
+ *
+ * Many thanks to Jeff Campbell and Mike Bradley for their extensive
+ * investigation, experimentation, testing, and suggested solutions of
+ * of audio/video sync problems with SVideo and CVBS captures.
+ */
+
+ /* the fast clock is at 200/245 MHz */
+ /* 1 * xtal_freq * 0x0d.f7df9b8 / 2 = 200 MHz: 400 MHz pre post-divide*/
+ /* 1 * xtal_freq * 0x11.1c71eb8 / 2 = 245 MHz: 490 MHz pre post-divide*/
+ cx18_write_reg(cx, lowpwr ? 0xD : 0x11, CX18_FAST_CLOCK_PLL_INT);
+ cx18_write_reg(cx, lowpwr ? 0x1EFBF37 : 0x038E3D7,
+ CX18_FAST_CLOCK_PLL_FRAC);
+
+ cx18_write_reg(cx, 2, CX18_FAST_CLOCK_PLL_POST);
+ cx18_write_reg(cx, 1, CX18_FAST_CLOCK_PLL_PRESCALE);
+ cx18_write_reg(cx, 4, CX18_FAST_CLOCK_PLL_ADJUST_BANDWIDTH);
+
+ /* set slow clock to 125/120 MHz */
+ /* xtal_freq * 0x0d.1861a20 / 3 = 125 MHz: 375 MHz before post-divide */
+ /* xtal_freq * 0x0c.92493f8 / 3 = 120 MHz: 360 MHz before post-divide */
+ cx18_write_reg(cx, lowpwr ? 0xD : 0xC, CX18_SLOW_CLOCK_PLL_INT);
+ cx18_write_reg(cx, lowpwr ? 0x30C344 : 0x124927F,
+ CX18_SLOW_CLOCK_PLL_FRAC);
+ cx18_write_reg(cx, 3, CX18_SLOW_CLOCK_PLL_POST);
+
+ /* mpeg clock pll 54MHz */
+ /* xtal_freq * 0xf.15f17f0 / 8 = 54 MHz: 432 MHz before post-divide */
+ cx18_write_reg(cx, 0xF, CX18_MPEG_CLOCK_PLL_INT);
+ cx18_write_reg(cx, 0x2BE2FE, CX18_MPEG_CLOCK_PLL_FRAC);
+ cx18_write_reg(cx, 8, CX18_MPEG_CLOCK_PLL_POST);
+
+ /* Defaults */
+ /* APU = SC or SC/2 = 125/62.5 */
+ /* EPU = SC = 125 */
+ /* DDR = FC = 180 */
+ /* ENC = SC = 125 */
+ /* AI1 = SC = 125 */
+ /* VIM2 = disabled */
+ /* PCI = FC/2 = 90 */
+ /* AI2 = disabled */
+ /* DEMUX = disabled */
+ /* AO = SC/2 = 62.5 */
+ /* SER = 54MHz */
+ /* VFC = disabled */
+ /* USB = disabled */
+
+ if (lowpwr) {
+ cx18_write_reg_expect(cx, 0xFFFF0020, CX18_CLOCK_SELECT1,
+ 0x00000020, 0xFFFFFFFF);
+ cx18_write_reg_expect(cx, 0xFFFF0004, CX18_CLOCK_SELECT2,
+ 0x00000004, 0xFFFFFFFF);
+ } else {
+ /* This doesn't explicitly set every clock select */
+ cx18_write_reg_expect(cx, 0x00060004, CX18_CLOCK_SELECT1,
+ 0x00000004, 0x00060006);
+ cx18_write_reg_expect(cx, 0x00060006, CX18_CLOCK_SELECT2,
+ 0x00000006, 0x00060006);
+ }
+
+ cx18_write_reg_expect(cx, 0xFFFF0002, CX18_HALF_CLOCK_SELECT1,
+ 0x00000002, 0xFFFFFFFF);
+ cx18_write_reg_expect(cx, 0xFFFF0104, CX18_HALF_CLOCK_SELECT2,
+ 0x00000104, 0xFFFFFFFF);
+ cx18_write_reg_expect(cx, 0xFFFF9026, CX18_CLOCK_ENABLE1,
+ 0x00009026, 0xFFFFFFFF);
+ cx18_write_reg_expect(cx, 0xFFFF3105, CX18_CLOCK_ENABLE2,
+ 0x00003105, 0xFFFFFFFF);
+}
+
+void cx18_init_memory(struct cx18 *cx)
+{
+ cx18_msleep_timeout(10, 0);
+ cx18_write_reg_expect(cx, 0x00010000, CX18_DDR_SOFT_RESET,
+ 0x00000000, 0x00010001);
+ cx18_msleep_timeout(10, 0);
+
+ cx18_write_reg(cx, cx->card->ddr.chip_config, CX18_DDR_CHIP_CONFIG);
+
+ cx18_msleep_timeout(10, 0);
+
+ cx18_write_reg(cx, cx->card->ddr.refresh, CX18_DDR_REFRESH);
+ cx18_write_reg(cx, cx->card->ddr.timing1, CX18_DDR_TIMING1);
+ cx18_write_reg(cx, cx->card->ddr.timing2, CX18_DDR_TIMING2);
+
+ cx18_msleep_timeout(10, 0);
+
+ /* Initialize DQS pad time */
+ cx18_write_reg(cx, cx->card->ddr.tune_lane, CX18_DDR_TUNE_LANE);
+ cx18_write_reg(cx, cx->card->ddr.initial_emrs, CX18_DDR_INITIAL_EMRS);
+
+ cx18_msleep_timeout(10, 0);
+
+ cx18_write_reg_expect(cx, 0x00020000, CX18_DDR_SOFT_RESET,
+ 0x00000000, 0x00020002);
+ cx18_msleep_timeout(10, 0);
+
+ /* use power-down mode when idle */
+ cx18_write_reg(cx, 0x00000010, CX18_DDR_POWER_REG);
+
+ cx18_write_reg_expect(cx, 0x00010001, CX18_REG_BUS_TIMEOUT_EN,
+ 0x00000001, 0x00010001);
+
+ cx18_write_reg(cx, 0x48, CX18_DDR_MB_PER_ROW_7);
+ cx18_write_reg(cx, 0xE0000, CX18_DDR_BASE_63_ADDR);
+
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT02); /* AO */
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT09); /* AI2 */
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT05); /* VIM1 */
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT06); /* AI1 */
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT07); /* 3D comb */
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT10); /* ME */
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT12); /* ENC */
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT13); /* PK */
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT11); /* RC */
+ cx18_write_reg(cx, 0x00000101, CX18_WMB_CLIENT14); /* AVO */
+}
+
+#define CX18_CPU_FIRMWARE "v4l-cx23418-cpu.fw"
+#define CX18_APU_FIRMWARE "v4l-cx23418-apu.fw"
+
+int cx18_firmware_init(struct cx18 *cx)
+{
+ u32 fw_entry_addr;
+ int sz, retries;
+ u32 api_args[MAX_MB_ARGUMENTS];
+
+ /* Allow chip to control CLKRUN */
+ cx18_write_reg(cx, 0x5, CX18_DSP0_INTERRUPT_MASK);
+
+ /* Stop the firmware */
+ cx18_write_reg_expect(cx, 0x000F000F, CX18_PROC_SOFT_RESET,
+ 0x0000000F, 0x000F000F);
+
+ cx18_msleep_timeout(1, 0);
+
+ /* If the CPU is still running */
+ if ((cx18_read_reg(cx, CX18_PROC_SOFT_RESET) & 8) == 0) {
+ CX18_ERR("%s: couldn't stop CPU to load firmware\n", __func__);
+ return -EIO;
+ }
+
+ cx18_sw1_irq_enable(cx, IRQ_CPU_TO_EPU | IRQ_APU_TO_EPU);
+ cx18_sw2_irq_enable(cx, IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK);
+
+ sz = load_cpu_fw_direct(CX18_CPU_FIRMWARE, cx->enc_mem, cx);
+ if (sz <= 0)
+ return sz;
+
+ /* The SCB & IPC area *must* be correct before starting the firmwares */
+ cx18_init_scb(cx);
+
+ fw_entry_addr = 0;
+ sz = load_apu_fw_direct(CX18_APU_FIRMWARE, cx->enc_mem, cx,
+ &fw_entry_addr);
+ if (sz <= 0)
+ return sz;
+
+ /* Start the CPU. The CPU will take care of the APU for us. */
+ cx18_write_reg_expect(cx, 0x00080000, CX18_PROC_SOFT_RESET,
+ 0x00000000, 0x00080008);
+
+ /* Wait up to 500 ms for the APU to come out of reset */
+ for (retries = 0;
+ retries < 50 && (cx18_read_reg(cx, CX18_PROC_SOFT_RESET) & 1) == 1;
+ retries++)
+ cx18_msleep_timeout(10, 0);
+
+ cx18_msleep_timeout(200, 0);
+
+ if (retries == 50 &&
+ (cx18_read_reg(cx, CX18_PROC_SOFT_RESET) & 1) == 1) {
+ CX18_ERR("Could not start the CPU\n");
+ return -EIO;
+ }
+
+ /*
+ * The CPU had once before set up to receive an interrupt for it's
+ * outgoing IRQ_CPU_TO_EPU_ACK to us. If it ever does this, we get an
+ * interrupt when it sends us an ack, but by the time we process it,
+ * that flag in the SW2 status register has been cleared by the CPU
+ * firmware. We'll prevent that not so useful condition from happening
+ * by clearing the CPU's interrupt enables for Ack IRQ's we want to
+ * process.
+ */
+ cx18_sw2_irq_disable_cpu(cx, IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK);
+
+ /* Try a benign command to see if the CPU is alive and well */
+ sz = cx18_vapi_result(cx, api_args, CX18_CPU_DEBUG_PEEK32, 1, 0);
+ if (sz < 0)
+ return sz;
+
+ /* initialize GPIO */
+ cx18_write_reg_expect(cx, 0x14001400, 0xc78110, 0x00001400, 0x14001400);
+ return 0;
+}
+
+MODULE_FIRMWARE(CX18_CPU_FIRMWARE);
+MODULE_FIRMWARE(CX18_APU_FIRMWARE);