v4.19.13 snapshot.
diff --git a/arch/x86/pci/fixup.c b/arch/x86/pci/fixup.c
new file mode 100644
index 0000000..13f4485
--- /dev/null
+++ b/arch/x86/pci/fixup.c
@@ -0,0 +1,757 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Exceptions for specific devices. Usually work-arounds for fatal design flaws.
+ */
+
+#include <linux/delay.h>
+#include <linux/dmi.h>
+#include <linux/pci.h>
+#include <linux/vgaarb.h>
+#include <asm/hpet.h>
+#include <asm/pci_x86.h>
+
+static void pci_fixup_i450nx(struct pci_dev *d)
+{
+ /*
+ * i450NX -- Find and scan all secondary buses on all PXB's.
+ */
+ int pxb, reg;
+ u8 busno, suba, subb;
+
+ dev_warn(&d->dev, "Searching for i450NX host bridges\n");
+ reg = 0xd0;
+ for(pxb = 0; pxb < 2; pxb++) {
+ pci_read_config_byte(d, reg++, &busno);
+ pci_read_config_byte(d, reg++, &suba);
+ pci_read_config_byte(d, reg++, &subb);
+ dev_dbg(&d->dev, "i450NX PXB %d: %02x/%02x/%02x\n", pxb, busno,
+ suba, subb);
+ if (busno)
+ pcibios_scan_root(busno); /* Bus A */
+ if (suba < subb)
+ pcibios_scan_root(suba+1); /* Bus B */
+ }
+ pcibios_last_bus = -1;
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82451NX, pci_fixup_i450nx);
+
+static void pci_fixup_i450gx(struct pci_dev *d)
+{
+ /*
+ * i450GX and i450KX -- Find and scan all secondary buses.
+ * (called separately for each PCI bridge found)
+ */
+ u8 busno;
+ pci_read_config_byte(d, 0x4a, &busno);
+ dev_info(&d->dev, "i440KX/GX host bridge; secondary bus %02x\n", busno);
+ pcibios_scan_root(busno);
+ pcibios_last_bus = -1;
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454GX, pci_fixup_i450gx);
+
+static void pci_fixup_umc_ide(struct pci_dev *d)
+{
+ /*
+ * UM8886BF IDE controller sets region type bits incorrectly,
+ * therefore they look like memory despite of them being I/O.
+ */
+ int i;
+
+ dev_warn(&d->dev, "Fixing base address flags\n");
+ for(i = 0; i < 4; i++)
+ d->resource[i].flags |= PCI_BASE_ADDRESS_SPACE_IO;
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886BF, pci_fixup_umc_ide);
+
+static void pci_fixup_latency(struct pci_dev *d)
+{
+ /*
+ * SiS 5597 and 5598 chipsets require latency timer set to
+ * at most 32 to avoid lockups.
+ */
+ dev_dbg(&d->dev, "Setting max latency to 32\n");
+ pcibios_max_latency = 32;
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, pci_fixup_latency);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5598, pci_fixup_latency);
+
+static void pci_fixup_piix4_acpi(struct pci_dev *d)
+{
+ /*
+ * PIIX4 ACPI device: hardwired IRQ9
+ */
+ d->irq = 9;
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, pci_fixup_piix4_acpi);
+
+/*
+ * Addresses issues with problems in the memory write queue timer in
+ * certain VIA Northbridges. This bugfix is per VIA's specifications,
+ * except for the KL133/KM133: clearing bit 5 on those Northbridges seems
+ * to trigger a bug in its integrated ProSavage video card, which
+ * causes screen corruption. We only clear bits 6 and 7 for that chipset,
+ * until VIA can provide us with definitive information on why screen
+ * corruption occurs, and what exactly those bits do.
+ *
+ * VIA 8363,8622,8361 Northbridges:
+ * - bits 5, 6, 7 at offset 0x55 need to be turned off
+ * VIA 8367 (KT266x) Northbridges:
+ * - bits 5, 6, 7 at offset 0x95 need to be turned off
+ * VIA 8363 rev 0x81/0x84 (KL133/KM133) Northbridges:
+ * - bits 6, 7 at offset 0x55 need to be turned off
+ */
+
+#define VIA_8363_KL133_REVISION_ID 0x81
+#define VIA_8363_KM133_REVISION_ID 0x84
+
+static void pci_fixup_via_northbridge_bug(struct pci_dev *d)
+{
+ u8 v;
+ int where = 0x55;
+ int mask = 0x1f; /* clear bits 5, 6, 7 by default */
+
+ if (d->device == PCI_DEVICE_ID_VIA_8367_0) {
+ /* fix pci bus latency issues resulted by NB bios error
+ it appears on bug free^Wreduced kt266x's bios forces
+ NB latency to zero */
+ pci_write_config_byte(d, PCI_LATENCY_TIMER, 0);
+
+ where = 0x95; /* the memory write queue timer register is
+ different for the KT266x's: 0x95 not 0x55 */
+ } else if (d->device == PCI_DEVICE_ID_VIA_8363_0 &&
+ (d->revision == VIA_8363_KL133_REVISION_ID ||
+ d->revision == VIA_8363_KM133_REVISION_ID)) {
+ mask = 0x3f; /* clear only bits 6 and 7; clearing bit 5
+ causes screen corruption on the KL133/KM133 */
+ }
+
+ pci_read_config_byte(d, where, &v);
+ if (v & ~mask) {
+ dev_warn(&d->dev, "Disabling VIA memory write queue (PCI ID %04x, rev %02x): [%02x] %02x & %02x -> %02x\n", \
+ d->device, d->revision, where, v, mask, v & mask);
+ v &= mask;
+ pci_write_config_byte(d, where, v);
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, pci_fixup_via_northbridge_bug);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8622, pci_fixup_via_northbridge_bug);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, pci_fixup_via_northbridge_bug);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8367_0, pci_fixup_via_northbridge_bug);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, pci_fixup_via_northbridge_bug);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8622, pci_fixup_via_northbridge_bug);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, pci_fixup_via_northbridge_bug);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8367_0, pci_fixup_via_northbridge_bug);
+
+/*
+ * For some reasons Intel decided that certain parts of their
+ * 815, 845 and some other chipsets must look like PCI-to-PCI bridges
+ * while they are obviously not. The 82801 family (AA, AB, BAM/CAM,
+ * BA/CA/DB and E) PCI bridges are actually HUB-to-PCI ones, according
+ * to Intel terminology. These devices do forward all addresses from
+ * system to PCI bus no matter what are their window settings, so they are
+ * "transparent" (or subtractive decoding) from programmers point of view.
+ */
+static void pci_fixup_transparent_bridge(struct pci_dev *dev)
+{
+ if ((dev->device & 0xff00) == 0x2400)
+ dev->transparent = 1;
+}
+DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
+ PCI_CLASS_BRIDGE_PCI, 8, pci_fixup_transparent_bridge);
+
+/*
+ * Fixup for C1 Halt Disconnect problem on nForce2 systems.
+ *
+ * From information provided by "Allen Martin" <AMartin@nvidia.com>:
+ *
+ * A hang is caused when the CPU generates a very fast CONNECT/HALT cycle
+ * sequence. Workaround is to set the SYSTEM_IDLE_TIMEOUT to 80 ns.
+ * This allows the state-machine and timer to return to a proper state within
+ * 80 ns of the CONNECT and probe appearing together. Since the CPU will not
+ * issue another HALT within 80 ns of the initial HALT, the failure condition
+ * is avoided.
+ */
+static void pci_fixup_nforce2(struct pci_dev *dev)
+{
+ u32 val;
+
+ /*
+ * Chip Old value New value
+ * C17 0x1F0FFF01 0x1F01FF01
+ * C18D 0x9F0FFF01 0x9F01FF01
+ *
+ * Northbridge chip version may be determined by
+ * reading the PCI revision ID (0xC1 or greater is C18D).
+ */
+ pci_read_config_dword(dev, 0x6c, &val);
+
+ /*
+ * Apply fixup if needed, but don't touch disconnect state
+ */
+ if ((val & 0x00FF0000) != 0x00010000) {
+ dev_warn(&dev->dev, "nForce2 C1 Halt Disconnect fixup\n");
+ pci_write_config_dword(dev, 0x6c, (val & 0xFF00FFFF) | 0x00010000);
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2, pci_fixup_nforce2);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2, pci_fixup_nforce2);
+
+/* Max PCI Express root ports */
+#define MAX_PCIEROOT 6
+static int quirk_aspm_offset[MAX_PCIEROOT << 3];
+
+#define GET_INDEX(a, b) ((((a) - PCI_DEVICE_ID_INTEL_MCH_PA) << 3) + ((b) & 7))
+
+static int quirk_pcie_aspm_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *value)
+{
+ return raw_pci_read(pci_domain_nr(bus), bus->number,
+ devfn, where, size, value);
+}
+
+/*
+ * Replace the original pci bus ops for write with a new one that will filter
+ * the request to insure ASPM cannot be enabled.
+ */
+static int quirk_pcie_aspm_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 value)
+{
+ u8 offset;
+
+ offset = quirk_aspm_offset[GET_INDEX(bus->self->device, devfn)];
+
+ if ((offset) && (where == offset))
+ value = value & ~PCI_EXP_LNKCTL_ASPMC;
+
+ return raw_pci_write(pci_domain_nr(bus), bus->number,
+ devfn, where, size, value);
+}
+
+static struct pci_ops quirk_pcie_aspm_ops = {
+ .read = quirk_pcie_aspm_read,
+ .write = quirk_pcie_aspm_write,
+};
+
+/*
+ * Prevents PCI Express ASPM (Active State Power Management) being enabled.
+ *
+ * Save the register offset, where the ASPM control bits are located,
+ * for each PCI Express device that is in the device list of
+ * the root port in an array for fast indexing. Replace the bus ops
+ * with the modified one.
+ */
+static void pcie_rootport_aspm_quirk(struct pci_dev *pdev)
+{
+ int i;
+ struct pci_bus *pbus;
+ struct pci_dev *dev;
+
+ if ((pbus = pdev->subordinate) == NULL)
+ return;
+
+ /*
+ * Check if the DID of pdev matches one of the six root ports. This
+ * check is needed in the case this function is called directly by the
+ * hot-plug driver.
+ */
+ if ((pdev->device < PCI_DEVICE_ID_INTEL_MCH_PA) ||
+ (pdev->device > PCI_DEVICE_ID_INTEL_MCH_PC1))
+ return;
+
+ if (list_empty(&pbus->devices)) {
+ /*
+ * If no device is attached to the root port at power-up or
+ * after hot-remove, the pbus->devices is empty and this code
+ * will set the offsets to zero and the bus ops to parent's bus
+ * ops, which is unmodified.
+ */
+ for (i = GET_INDEX(pdev->device, 0); i <= GET_INDEX(pdev->device, 7); ++i)
+ quirk_aspm_offset[i] = 0;
+
+ pci_bus_set_ops(pbus, pbus->parent->ops);
+ } else {
+ /*
+ * If devices are attached to the root port at power-up or
+ * after hot-add, the code loops through the device list of
+ * each root port to save the register offsets and replace the
+ * bus ops.
+ */
+ list_for_each_entry(dev, &pbus->devices, bus_list)
+ /* There are 0 to 8 devices attached to this bus */
+ quirk_aspm_offset[GET_INDEX(pdev->device, dev->devfn)] =
+ dev->pcie_cap + PCI_EXP_LNKCTL;
+
+ pci_bus_set_ops(pbus, &quirk_pcie_aspm_ops);
+ dev_info(&pbus->dev, "writes to ASPM control bits will be ignored\n");
+ }
+
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PA, pcie_rootport_aspm_quirk);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PA1, pcie_rootport_aspm_quirk);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PB, pcie_rootport_aspm_quirk);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PB1, pcie_rootport_aspm_quirk);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC, pcie_rootport_aspm_quirk);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC1, pcie_rootport_aspm_quirk);
+
+/*
+ * Fixup to mark boot BIOS video selected by BIOS before it changes
+ *
+ * From information provided by "Jon Smirl" <jonsmirl@gmail.com>
+ *
+ * The standard boot ROM sequence for an x86 machine uses the BIOS
+ * to select an initial video card for boot display. This boot video
+ * card will have its BIOS copied to 0xC0000 in system RAM.
+ * IORESOURCE_ROM_SHADOW is used to associate the boot video
+ * card with this copy. On laptops this copy has to be used since
+ * the main ROM may be compressed or combined with another image.
+ * See pci_map_rom() for use of this flag. Before marking the device
+ * with IORESOURCE_ROM_SHADOW check if a vga_default_device is already set
+ * by either arch code or vga-arbitration; if so only apply the fixup to this
+ * already-determined primary video card.
+ */
+
+static void pci_fixup_video(struct pci_dev *pdev)
+{
+ struct pci_dev *bridge;
+ struct pci_bus *bus;
+ u16 config;
+ struct resource *res;
+
+ /* Is VGA routed to us? */
+ bus = pdev->bus;
+ while (bus) {
+ bridge = bus->self;
+
+ /*
+ * From information provided by
+ * "David Miller" <davem@davemloft.net>
+ * The bridge control register is valid for PCI header
+ * type BRIDGE, or CARDBUS. Host to PCI controllers use
+ * PCI header type NORMAL.
+ */
+ if (bridge && (pci_is_bridge(bridge))) {
+ pci_read_config_word(bridge, PCI_BRIDGE_CONTROL,
+ &config);
+ if (!(config & PCI_BRIDGE_CTL_VGA))
+ return;
+ }
+ bus = bus->parent;
+ }
+ if (!vga_default_device() || pdev == vga_default_device()) {
+ pci_read_config_word(pdev, PCI_COMMAND, &config);
+ if (config & (PCI_COMMAND_IO | PCI_COMMAND_MEMORY)) {
+ res = &pdev->resource[PCI_ROM_RESOURCE];
+
+ pci_disable_rom(pdev);
+ if (res->parent)
+ release_resource(res);
+
+ res->start = 0xC0000;
+ res->end = res->start + 0x20000 - 1;
+ res->flags = IORESOURCE_MEM | IORESOURCE_ROM_SHADOW |
+ IORESOURCE_PCI_FIXED;
+ dev_info(&pdev->dev, "Video device with shadowed ROM at %pR\n",
+ res);
+ }
+ }
+}
+DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
+ PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video);
+
+
+static const struct dmi_system_id msi_k8t_dmi_table[] = {
+ {
+ .ident = "MSI-K8T-Neo2Fir",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "MSI"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "MS-6702E"),
+ },
+ },
+ {}
+};
+
+/*
+ * The AMD-Athlon64 board MSI "K8T Neo2-FIR" disables the onboard sound
+ * card if a PCI-soundcard is added.
+ *
+ * The BIOS only gives options "DISABLED" and "AUTO". This code sets
+ * the corresponding register-value to enable the soundcard.
+ *
+ * The soundcard is only enabled, if the mainborad is identified
+ * via DMI-tables and the soundcard is detected to be off.
+ */
+static void pci_fixup_msi_k8t_onboard_sound(struct pci_dev *dev)
+{
+ unsigned char val;
+ if (!dmi_check_system(msi_k8t_dmi_table))
+ return; /* only applies to MSI K8T Neo2-FIR */
+
+ pci_read_config_byte(dev, 0x50, &val);
+ if (val & 0x40) {
+ pci_write_config_byte(dev, 0x50, val & (~0x40));
+
+ /* verify the change for status output */
+ pci_read_config_byte(dev, 0x50, &val);
+ if (val & 0x40)
+ dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; "
+ "can't enable onboard soundcard!\n");
+ else
+ dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; "
+ "enabled onboard soundcard\n");
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237,
+ pci_fixup_msi_k8t_onboard_sound);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237,
+ pci_fixup_msi_k8t_onboard_sound);
+
+/*
+ * Some Toshiba laptops need extra code to enable their TI TSB43AB22/A.
+ *
+ * We pretend to bring them out of full D3 state, and restore the proper
+ * IRQ, PCI cache line size, and BARs, otherwise the device won't function
+ * properly. In some cases, the device will generate an interrupt on
+ * the wrong IRQ line, causing any devices sharing the line it's
+ * *supposed* to use to be disabled by the kernel's IRQ debug code.
+ */
+static u16 toshiba_line_size;
+
+static const struct dmi_system_id toshiba_ohci1394_dmi_table[] = {
+ {
+ .ident = "Toshiba PS5 based laptop",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "PS5"),
+ },
+ },
+ {
+ .ident = "Toshiba PSM4 based laptop",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "PSM4"),
+ },
+ },
+ {
+ .ident = "Toshiba A40 based laptop",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_VERSION, "PSA40U"),
+ },
+ },
+ { }
+};
+
+static void pci_pre_fixup_toshiba_ohci1394(struct pci_dev *dev)
+{
+ if (!dmi_check_system(toshiba_ohci1394_dmi_table))
+ return; /* only applies to certain Toshibas (so far) */
+
+ dev->current_state = PCI_D3cold;
+ pci_read_config_word(dev, PCI_CACHE_LINE_SIZE, &toshiba_line_size);
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TI, 0x8032,
+ pci_pre_fixup_toshiba_ohci1394);
+
+static void pci_post_fixup_toshiba_ohci1394(struct pci_dev *dev)
+{
+ if (!dmi_check_system(toshiba_ohci1394_dmi_table))
+ return; /* only applies to certain Toshibas (so far) */
+
+ /* Restore config space on Toshiba laptops */
+ pci_write_config_word(dev, PCI_CACHE_LINE_SIZE, toshiba_line_size);
+ pci_read_config_byte(dev, PCI_INTERRUPT_LINE, (u8 *)&dev->irq);
+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0,
+ pci_resource_start(dev, 0));
+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_1,
+ pci_resource_start(dev, 1));
+}
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_TI, 0x8032,
+ pci_post_fixup_toshiba_ohci1394);
+
+
+/*
+ * Prevent the BIOS trapping accesses to the Cyrix CS5530A video device
+ * configuration space.
+ */
+static void pci_early_fixup_cyrix_5530(struct pci_dev *dev)
+{
+ u8 r;
+ /* clear 'F4 Video Configuration Trap' bit */
+ pci_read_config_byte(dev, 0x42, &r);
+ r &= 0xfd;
+ pci_write_config_byte(dev, 0x42, r);
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY,
+ pci_early_fixup_cyrix_5530);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY,
+ pci_early_fixup_cyrix_5530);
+
+/*
+ * Siemens Nixdorf AG FSC Multiprocessor Interrupt Controller:
+ * prevent update of the BAR0, which doesn't look like a normal BAR.
+ */
+static void pci_siemens_interrupt_controller(struct pci_dev *dev)
+{
+ dev->resource[0].flags |= IORESOURCE_PCI_FIXED;
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SIEMENS, 0x0015,
+ pci_siemens_interrupt_controller);
+
+/*
+ * SB600: Disable BAR1 on device 14.0 to avoid HPET resources from
+ * confusing the PCI engine:
+ */
+static void sb600_disable_hpet_bar(struct pci_dev *dev)
+{
+ u8 val;
+
+ /*
+ * The SB600 and SB700 both share the same device
+ * ID, but the PM register 0x55 does something different
+ * for the SB700, so make sure we are dealing with the
+ * SB600 before touching the bit:
+ */
+
+ pci_read_config_byte(dev, 0x08, &val);
+
+ if (val < 0x2F) {
+ outb(0x55, 0xCD6);
+ val = inb(0xCD7);
+
+ /* Set bit 7 in PM register 0x55 */
+ outb(0x55, 0xCD6);
+ outb(val | 0x80, 0xCD7);
+ }
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ATI, 0x4385, sb600_disable_hpet_bar);
+
+#ifdef CONFIG_HPET_TIMER
+static void sb600_hpet_quirk(struct pci_dev *dev)
+{
+ struct resource *r = &dev->resource[1];
+
+ if (r->flags & IORESOURCE_MEM && r->start == hpet_address) {
+ r->flags |= IORESOURCE_PCI_FIXED;
+ dev_info(&dev->dev, "reg 0x14 contains HPET; making it immovable\n");
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, 0x4385, sb600_hpet_quirk);
+#endif
+
+/*
+ * Twinhead H12Y needs us to block out a region otherwise we map devices
+ * there and any access kills the box.
+ *
+ * See: https://bugzilla.kernel.org/show_bug.cgi?id=10231
+ *
+ * Match off the LPC and svid/sdid (older kernels lose the bridge subvendor)
+ */
+static void twinhead_reserve_killing_zone(struct pci_dev *dev)
+{
+ if (dev->subsystem_vendor == 0x14FF && dev->subsystem_device == 0xA003) {
+ pr_info("Reserving memory on Twinhead H12Y\n");
+ request_mem_region(0xFFB00000, 0x100000, "twinhead");
+ }
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x27B9, twinhead_reserve_killing_zone);
+
+/*
+ * Device [8086:2fc0]
+ * Erratum HSE43
+ * CONFIG_TDP_NOMINAL CSR Implemented at Incorrect Offset
+ * http://www.intel.com/content/www/us/en/processors/xeon/xeon-e5-v3-spec-update.html
+ *
+ * Devices [8086:6f60,6fa0,6fc0]
+ * Erratum BDF2
+ * PCI BARs in the Home Agent Will Return Non-Zero Values During Enumeration
+ * http://www.intel.com/content/www/us/en/processors/xeon/xeon-e5-v4-spec-update.html
+ */
+static void pci_invalid_bar(struct pci_dev *dev)
+{
+ dev->non_compliant_bars = 1;
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x2fc0, pci_invalid_bar);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x6f60, pci_invalid_bar);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x6fa0, pci_invalid_bar);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x6fc0, pci_invalid_bar);
+
+/*
+ * Device [1022:7808]
+ * 23. USB Wake on Connect/Disconnect with Low Speed Devices
+ * https://support.amd.com/TechDocs/46837.pdf
+ * Appendix A2
+ * https://support.amd.com/TechDocs/42413.pdf
+ */
+static void pci_fixup_amd_ehci_pme(struct pci_dev *dev)
+{
+ dev_info(&dev->dev, "PME# does not work under D3, disabling it\n");
+ dev->pme_support &= ~((PCI_PM_CAP_PME_D3 | PCI_PM_CAP_PME_D3cold)
+ >> PCI_PM_CAP_PME_SHIFT);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x7808, pci_fixup_amd_ehci_pme);
+
+/*
+ * Apple MacBook Pro: Avoid [mem 0x7fa00000-0x7fbfffff]
+ *
+ * Using the [mem 0x7fa00000-0x7fbfffff] region, e.g., by assigning it to
+ * the 00:1c.0 Root Port, causes a conflict with [io 0x1804], which is used
+ * for soft poweroff and suspend-to-RAM.
+ *
+ * As far as we know, this is related to the address space, not to the Root
+ * Port itself. Attaching the quirk to the Root Port is a convenience, but
+ * it could probably also be a standalone DMI quirk.
+ *
+ * https://bugzilla.kernel.org/show_bug.cgi?id=103211
+ */
+static void quirk_apple_mbp_poweroff(struct pci_dev *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+
+ if ((!dmi_match(DMI_PRODUCT_NAME, "MacBookPro11,4") &&
+ !dmi_match(DMI_PRODUCT_NAME, "MacBookPro11,5")) ||
+ pdev->bus->number != 0 || pdev->devfn != PCI_DEVFN(0x1c, 0))
+ return;
+
+ res = request_mem_region(0x7fa00000, 0x200000,
+ "MacBook Pro poweroff workaround");
+ if (res)
+ dev_info(dev, "claimed %s %pR\n", res->name, res);
+ else
+ dev_info(dev, "can't work around MacBook Pro poweroff issue\n");
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8c10, quirk_apple_mbp_poweroff);
+
+/*
+ * VMD-enabled root ports will change the source ID for all messages
+ * to the VMD device. Rather than doing device matching with the source
+ * ID, the AER driver should traverse the child device tree, reading
+ * AER registers to find the faulting device.
+ */
+static void quirk_no_aersid(struct pci_dev *pdev)
+{
+ /* VMD Domain */
+ if (is_vmd(pdev->bus))
+ pdev->bus->bus_flags |= PCI_BUS_FLAGS_NO_AERSID;
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x2030, quirk_no_aersid);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x2031, quirk_no_aersid);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x2032, quirk_no_aersid);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x2033, quirk_no_aersid);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x334a, quirk_no_aersid);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x334b, quirk_no_aersid);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x334c, quirk_no_aersid);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x334d, quirk_no_aersid);
+
+#ifdef CONFIG_PHYS_ADDR_T_64BIT
+
+#define AMD_141b_MMIO_BASE(x) (0x80 + (x) * 0x8)
+#define AMD_141b_MMIO_BASE_RE_MASK BIT(0)
+#define AMD_141b_MMIO_BASE_WE_MASK BIT(1)
+#define AMD_141b_MMIO_BASE_MMIOBASE_MASK GENMASK(31,8)
+
+#define AMD_141b_MMIO_LIMIT(x) (0x84 + (x) * 0x8)
+#define AMD_141b_MMIO_LIMIT_MMIOLIMIT_MASK GENMASK(31,8)
+
+#define AMD_141b_MMIO_HIGH(x) (0x180 + (x) * 0x4)
+#define AMD_141b_MMIO_HIGH_MMIOBASE_MASK GENMASK(7,0)
+#define AMD_141b_MMIO_HIGH_MMIOLIMIT_SHIFT 16
+#define AMD_141b_MMIO_HIGH_MMIOLIMIT_MASK GENMASK(23,16)
+
+/*
+ * The PCI Firmware Spec, rev 3.2, notes that ACPI should optionally allow
+ * configuring host bridge windows using the _PRS and _SRS methods.
+ *
+ * But this is rarely implemented, so we manually enable a large 64bit BAR for
+ * PCIe device on AMD Family 15h (Models 00h-1fh, 30h-3fh, 60h-7fh) Processors
+ * here.
+ */
+static void pci_amd_enable_64bit_bar(struct pci_dev *dev)
+{
+ static const char *name = "PCI Bus 0000:00";
+ struct resource *res, *conflict;
+ u32 base, limit, high;
+ struct pci_dev *other;
+ unsigned i;
+
+ if (!(pci_probe & PCI_BIG_ROOT_WINDOW))
+ return;
+
+ /* Check that we are the only device of that type */
+ other = pci_get_device(dev->vendor, dev->device, NULL);
+ if (other != dev ||
+ (other = pci_get_device(dev->vendor, dev->device, other))) {
+ /* This is a multi-socket system, don't touch it for now */
+ pci_dev_put(other);
+ return;
+ }
+
+ for (i = 0; i < 8; i++) {
+ pci_read_config_dword(dev, AMD_141b_MMIO_BASE(i), &base);
+ pci_read_config_dword(dev, AMD_141b_MMIO_HIGH(i), &high);
+
+ /* Is this slot free? */
+ if (!(base & (AMD_141b_MMIO_BASE_RE_MASK |
+ AMD_141b_MMIO_BASE_WE_MASK)))
+ break;
+
+ base >>= 8;
+ base |= high << 24;
+
+ /* Abort if a slot already configures a 64bit BAR. */
+ if (base > 0x10000)
+ return;
+ }
+ if (i == 8)
+ return;
+
+ res = kzalloc(sizeof(*res), GFP_KERNEL);
+ if (!res)
+ return;
+
+ /*
+ * Allocate a 256GB window directly below the 0xfd00000000 hardware
+ * limit (see AMD Family 15h Models 30h-3Fh BKDG, sec 2.4.6).
+ */
+ res->name = name;
+ res->flags = IORESOURCE_PREFETCH | IORESOURCE_MEM |
+ IORESOURCE_MEM_64 | IORESOURCE_WINDOW;
+ res->start = 0xbd00000000ull;
+ res->end = 0xfd00000000ull - 1;
+
+ conflict = request_resource_conflict(&iomem_resource, res);
+ if (conflict) {
+ kfree(res);
+ if (conflict->name != name)
+ return;
+
+ /* We are resuming from suspend; just reenable the window */
+ res = conflict;
+ } else {
+ dev_info(&dev->dev, "adding root bus resource %pR (tainting kernel)\n",
+ res);
+ add_taint(TAINT_FIRMWARE_WORKAROUND, LOCKDEP_STILL_OK);
+ pci_bus_add_resource(dev->bus, res, 0);
+ }
+
+ base = ((res->start >> 8) & AMD_141b_MMIO_BASE_MMIOBASE_MASK) |
+ AMD_141b_MMIO_BASE_RE_MASK | AMD_141b_MMIO_BASE_WE_MASK;
+ limit = ((res->end + 1) >> 8) & AMD_141b_MMIO_LIMIT_MMIOLIMIT_MASK;
+ high = ((res->start >> 40) & AMD_141b_MMIO_HIGH_MMIOBASE_MASK) |
+ ((((res->end + 1) >> 40) << AMD_141b_MMIO_HIGH_MMIOLIMIT_SHIFT)
+ & AMD_141b_MMIO_HIGH_MMIOLIMIT_MASK);
+
+ pci_write_config_dword(dev, AMD_141b_MMIO_HIGH(i), high);
+ pci_write_config_dword(dev, AMD_141b_MMIO_LIMIT(i), limit);
+ pci_write_config_dword(dev, AMD_141b_MMIO_BASE(i), base);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x1401, pci_amd_enable_64bit_bar);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x141b, pci_amd_enable_64bit_bar);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x1571, pci_amd_enable_64bit_bar);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x15b1, pci_amd_enable_64bit_bar);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x1601, pci_amd_enable_64bit_bar);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x1401, pci_amd_enable_64bit_bar);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x141b, pci_amd_enable_64bit_bar);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x1571, pci_amd_enable_64bit_bar);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x15b1, pci_amd_enable_64bit_bar);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x1601, pci_amd_enable_64bit_bar);
+
+#endif