v4.19.13 snapshot.
diff --git a/arch/arm/mach-ixp4xx/ixdp425-setup.c b/arch/arm/mach-ixp4xx/ixdp425-setup.c
new file mode 100644
index 0000000..3ec829d
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c
@@ -0,0 +1,317 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * arch/arm/mach-ixp4xx/ixdp425-setup.c
+ *
+ * IXDP425/IXCDP1100 board-setup
+ *
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Deepak Saxena <dsaxena@plexity.net>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/gpio/machine.h>
+#include <linux/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <mach/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+#define IXDP425_SDA_PIN 7
+#define IXDP425_SCL_PIN 6
+
+/* NAND Flash pins */
+#define IXDP425_NAND_NCE_PIN 12
+
+#define IXDP425_NAND_CMD_BYTE 0x01
+#define IXDP425_NAND_ADDR_BYTE 0x02
+
+static struct flash_platform_data ixdp425_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource ixdp425_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ixdp425_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &ixdp425_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &ixdp425_flash_resource,
+};
+
+#if defined(CONFIG_MTD_NAND_PLATFORM) || \
+ defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+
+static struct mtd_partition ixdp425_partitions[] = {
+ {
+ .name = "ixp400 NAND FS 0",
+ .offset = 0,
+ .size = SZ_8M
+ }, {
+ .name = "ixp400 NAND FS 1",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+static void
+ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+ struct nand_chip *this = mtd_to_nand(mtd);
+ int offset = (int)nand_get_controller_data(this);
+
+ if (ctrl & NAND_CTRL_CHANGE) {
+ if (ctrl & NAND_NCE) {
+ gpio_set_value(IXDP425_NAND_NCE_PIN, 0);
+ udelay(5);
+ } else
+ gpio_set_value(IXDP425_NAND_NCE_PIN, 1);
+
+ offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
+ offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
+ nand_set_controller_data(this, (void *)offset);
+ }
+
+ if (cmd != NAND_CMD_NONE)
+ writeb(cmd, this->IO_ADDR_W + offset);
+}
+
+static struct platform_nand_data ixdp425_flash_nand_data = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_delay = 30,
+ .partitions = ixdp425_partitions,
+ .nr_partitions = ARRAY_SIZE(ixdp425_partitions),
+ },
+ .ctrl = {
+ .cmd_ctrl = ixdp425_flash_nand_cmd_ctrl
+ }
+};
+
+static struct resource ixdp425_flash_nand_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ixdp425_flash_nand = {
+ .name = "gen_nand",
+ .id = -1,
+ .dev = {
+ .platform_data = &ixdp425_flash_nand_data,
+ },
+ .num_resources = 1,
+ .resource = &ixdp425_flash_nand_resource,
+};
+#endif /* CONFIG_MTD_NAND_PLATFORM */
+
+static struct gpiod_lookup_table ixdp425_i2c_gpiod_table = {
+ .dev_id = "i2c-gpio.0",
+ .table = {
+ GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", IXDP425_SDA_PIN,
+ NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+ GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", IXDP425_SCL_PIN,
+ NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
+ },
+};
+
+static struct platform_device ixdp425_i2c_gpio = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = NULL,
+ },
+};
+
+static struct resource ixdp425_uart_resources[] = {
+ {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ }
+};
+
+static struct plat_serial8250_port ixdp425_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device ixdp425_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev.platform_data = ixdp425_uart_data,
+ .num_resources = 2,
+ .resource = ixdp425_uart_resources
+};
+
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info ixdp425_plat_eth[] = {
+ {
+ .phy = 0,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device ixdp425_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = ixdp425_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = ixdp425_plat_eth + 1,
+ }
+};
+
+static struct platform_device *ixdp425_devices[] __initdata = {
+ &ixdp425_i2c_gpio,
+ &ixdp425_flash,
+#if defined(CONFIG_MTD_NAND_PLATFORM) || \
+ defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+ &ixdp425_flash_nand,
+#endif
+ &ixdp425_uart,
+ &ixdp425_eth[0],
+ &ixdp425_eth[1],
+};
+
+static void __init ixdp425_init(void)
+{
+ ixp4xx_sys_init();
+
+ ixdp425_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ ixdp425_flash_resource.end =
+ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
+
+#if defined(CONFIG_MTD_NAND_PLATFORM) || \
+ defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
+ ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
+ ixdp425_flash_nand_resource.end = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
+
+ gpio_request(IXDP425_NAND_NCE_PIN, "NAND NCE pin");
+ gpio_direction_output(IXDP425_NAND_NCE_PIN, 0);
+
+ /* Configure expansion bus for NAND Flash */
+ *IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
+ IXP4XX_EXP_BUS_STROBE_T(1) | /* extend by 1 clock */
+ IXP4XX_EXP_BUS_CYCLES(0) | /* Intel cycles */
+ IXP4XX_EXP_BUS_SIZE(0) | /* 512bytes addr space*/
+ IXP4XX_EXP_BUS_WR_EN |
+ IXP4XX_EXP_BUS_BYTE_EN; /* 8 bit data bus */
+#endif
+
+ if (cpu_is_ixp43x()) {
+ ixdp425_uart.num_resources = 1;
+ ixdp425_uart_data[1].flags = 0;
+ }
+
+ gpiod_add_lookup_table(&ixdp425_i2c_gpiod_table);
+ platform_add_devices(ixdp425_devices, ARRAY_SIZE(ixdp425_devices));
+}
+
+#ifdef CONFIG_ARCH_IXDP425
+MACHINE_START(IXDP425, "Intel IXDP425 Development Platform")
+ /* Maintainer: MontaVista Software, Inc. */
+ .map_io = ixp4xx_map_io,
+ .init_early = ixp4xx_init_early,
+ .init_irq = ixp4xx_init_irq,
+ .init_time = ixp4xx_timer_init,
+ .atag_offset = 0x100,
+ .init_machine = ixdp425_init,
+#if defined(CONFIG_PCI)
+ .dma_zone_size = SZ_64M,
+#endif
+ .restart = ixp4xx_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_IXDP465
+MACHINE_START(IXDP465, "Intel IXDP465 Development Platform")
+ /* Maintainer: MontaVista Software, Inc. */
+ .map_io = ixp4xx_map_io,
+ .init_early = ixp4xx_init_early,
+ .init_irq = ixp4xx_init_irq,
+ .init_time = ixp4xx_timer_init,
+ .atag_offset = 0x100,
+ .init_machine = ixdp425_init,
+#if defined(CONFIG_PCI)
+ .dma_zone_size = SZ_64M,
+#endif
+MACHINE_END
+#endif
+
+#ifdef CONFIG_ARCH_PRPMC1100
+MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform")
+ /* Maintainer: MontaVista Software, Inc. */
+ .map_io = ixp4xx_map_io,
+ .init_early = ixp4xx_init_early,
+ .init_irq = ixp4xx_init_irq,
+ .init_time = ixp4xx_timer_init,
+ .atag_offset = 0x100,
+ .init_machine = ixdp425_init,
+#if defined(CONFIG_PCI)
+ .dma_zone_size = SZ_64M,
+#endif
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_KIXRP435
+MACHINE_START(KIXRP435, "Intel KIXRP435 Reference Platform")
+ /* Maintainer: MontaVista Software, Inc. */
+ .map_io = ixp4xx_map_io,
+ .init_early = ixp4xx_init_early,
+ .init_irq = ixp4xx_init_irq,
+ .init_time = ixp4xx_timer_init,
+ .atag_offset = 0x100,
+ .init_machine = ixdp425_init,
+#if defined(CONFIG_PCI)
+ .dma_zone_size = SZ_64M,
+#endif
+MACHINE_END
+#endif