v4.19.13 snapshot.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
new file mode 100644
index 0000000..a5b4f22
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -0,0 +1,1687 @@
+What: /sys/bus/iio/devices/iio:deviceX
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Hardware chip or device accessed by one communication port.
+ Corresponds to a grouping of sensor channels. X is the IIO
+ index of the device.
+
+What: /sys/bus/iio/devices/triggerX
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ An event driven driver of data capture to an in kernel buffer.
+ May be provided by a device driver that also has an IIO device
+ based on hardware generated events (e.g. data ready) or
+ provided by a separate driver for other hardware (e.g.
+ periodic timer, GPIO or high resolution timer).
+ Contains trigger type specific elements. These do not
+ generalize well and hence are not documented in this file.
+ X is the IIO index of the trigger.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Directory of attributes relating to the buffer for the device.
+
+What: /sys/bus/iio/devices/iio:deviceX/name
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Description of the physical chip / device for device X.
+ Typically a part number.
+
+What: /sys/bus/iio/devices/iio:deviceX/current_timestamp_clock
+KernelVersion: 4.5
+Contact: linux-iio@vger.kernel.org
+Description:
+ String identifying current posix clock used to timestamp
+ buffered samples and events for device X.
+
+What: /sys/bus/iio/devices/iio:deviceX/sampling_frequency
+What: /sys/bus/iio/devices/iio:deviceX/buffer/sampling_frequency
+What: /sys/bus/iio/devices/triggerX/sampling_frequency
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Some devices have internal clocks. This parameter sets the
+ resulting sampling frequency. In many devices this
+ parameter has an effect on input filters etc. rather than
+ simply controlling when the input is sampled. As this
+ effects data ready triggers, hardware buffers and the sysfs
+ direct access interfaces, it may be found in any of the
+ relevant directories. If it effects all of the above
+ then it is to be found in the base device directory.
+
+What: /sys/bus/iio/devices/iio:deviceX/sampling_frequency_available
+What: /sys/bus/iio/devices/iio:deviceX/in_proximity_sampling_frequency_available
+What: /sys/.../iio:deviceX/buffer/sampling_frequency_available
+What: /sys/bus/iio/devices/triggerX/sampling_frequency_available
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ When the internal sampling clock can only take a small
+ discrete set of values, this file lists those available.
+
+What: /sys/bus/iio/devices/iio:deviceX/oversampling_ratio
+KernelVersion: 2.6.38
+Contact: linux-iio@vger.kernel.org
+Description:
+ Hardware dependent ADC oversampling. Controls the sampling ratio
+ of the digital filter if available.
+
+What: /sys/bus/iio/devices/iio:deviceX/oversampling_ratio_available
+KernelVersion: 2.6.38
+Contact: linux-iio@vger.kernel.org
+Description:
+ Hardware dependent values supported by the oversampling filter.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_i_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_q_raw
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled no bias removal etc.) voltage measurement from
+ channel Y. In special cases where the channel does not
+ correspond to externally available input one of the named
+ versions may be used. The number must always be specified and
+ unique to allow association with event codes. Units after
+ application of scale and offset are millivolts.
+
+ Channels with 'i' and 'q' modifiers always exist in pairs and both
+ channels refer to the same signal. The 'i' channel contains the in-phase
+ component of the signal while the 'q' channel contains the quadrature
+ component.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY-voltageZ_raw
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled) differential voltage measurement equivalent to
+ channel Y - channel Z where these channel numbers apply to the
+ physically equivalent inputs when non differential readings are
+ separately available. In differential only parts, then all that
+ is required is a consistent labeling. Units after application
+ of scale and offset are millivolts.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_currentY_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_currentY_supply_raw
+KernelVersion: 3.17
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled no bias removal etc.) current measurement from
+ channel Y. In special cases where the channel does not
+ correspond to externally available input one of the named
+ versions may be used. The number must always be specified and
+ unique to allow association with event codes. Units after
+ application of scale and offset are milliamps.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_powerY_raw
+KernelVersion: 4.5
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled no bias removal etc.) power measurement from
+ channel Y. The number must always be specified and
+ unique to allow association with event codes. Units after
+ application of scale and offset are milliwatts.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_capacitanceY_raw
+KernelVersion: 3.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw capacitance measurement from channel Y. Units after
+ application of scale and offset are nanofarads.
+
+What: /sys/.../iio:deviceX/in_capacitanceY-in_capacitanceZ_raw
+KernelVersion: 3.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw differential capacitance measurement equivalent to
+ channel Y - channel Z where these channel numbers apply to the
+ physically equivalent inputs when non differential readings are
+ separately available. In differential only parts, then all that
+ is required is a consistent labeling. Units after application
+ of scale and offset are nanofarads.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_temp_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_tempX_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_temp_x_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_temp_y_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_temp_ambient_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_temp_object_raw
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled no bias removal etc.) temperature measurement.
+ If an axis is specified it generally means that the temperature
+ sensor is associated with one part of a compound device (e.g.
+ a gyroscope axis). The ambient and object modifiers distinguish
+ between ambient (reference) and distant temperature for contact-
+ less measurements. Units after application of scale and offset
+ are milli degrees Celsius.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_tempX_input
+KernelVersion: 2.6.38
+Contact: linux-iio@vger.kernel.org
+Description:
+ Scaled temperature measurement in milli degrees Celsius.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_raw
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Acceleration in direction x, y or z (may be arbitrarily assigned
+ but should match other such assignments on device).
+ Has all of the equivalent parameters as per voltageY. Units
+ after application of scale and offset are m/s^2.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_gravity_x_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_gravity_y_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_gravity_z_raw
+KernelVersion: 4.11
+Contact: linux-iio@vger.kernel.org
+Description:
+ Gravity in direction x, y or z (may be arbitrarily assigned
+ but should match other such assignments on device).
+ Units after application of scale and offset are m/s^2.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_angl_raw
+KernelVersion: 4.17
+Contact: linux-iio@vger.kernel.org
+Description:
+ Angle of rotation. Units after application of scale and offset
+ are radians.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_positionrelative_x_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_positionrelative_y_raw
+KernelVersion: 4.18
+Contact: linux-iio@vger.kernel.org
+Description:
+ Relative position in direction x or y on a pad (may be
+ arbitrarily assigned but should match other such assignments on
+ device).
+ Units after application of scale and offset are milli percents
+ from the pad's size in both directions. Should be calibrated by
+ the consumer.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_raw
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Angular velocity about axis x, y or z (may be arbitrarily
+ assigned). Has all the equivalent parameters as per voltageY.
+ Units after application of scale and offset are radians per
+ second.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_incli_x_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_incli_y_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_incli_z_raw
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Inclination raw reading about axis x, y or z (may be
+ arbitrarily assigned). Data converted by application of offset
+ and scale to degrees.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_z_raw
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Magnetic field along axis x, y or z (may be arbitrarily
+ assigned). Data converted by application of offset
+ then scale to Gauss.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_peak_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_peak_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_peak_raw
+KernelVersion: 2.6.36
+Contact: linux-iio@vger.kernel.org
+Description:
+ Highest value since some reset condition. These
+ attributes allow access to this and are otherwise
+ the direct equivalent of the <type>Y[_name]_raw attributes.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_xyz_squared_peak_raw
+KernelVersion: 2.6.36
+Contact: linux-iio@vger.kernel.org
+Description:
+ A computed peak value based on the sum squared magnitude of
+ the underlying value in the specified directions.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_pressure_raw
+KernelVersion: 3.8
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw pressure measurement from channel Y. Units after
+ application of scale and offset are kilopascal.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_input
+What: /sys/bus/iio/devices/iio:deviceX/in_pressure_input
+KernelVersion: 3.8
+Contact: linux-iio@vger.kernel.org
+Description:
+ Scaled pressure measurement from channel Y, in kilopascal.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_humidityrelative_raw
+KernelVersion: 3.14
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw humidity measurement of air. Units after application of
+ scale and offset are milli percent.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_humidityrelative_input
+KernelVersion: 3.14
+Contact: linux-iio@vger.kernel.org
+Description:
+ Scaled humidity measurement in milli percent.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_X_mean_raw
+KernelVersion: 3.5
+Contact: linux-iio@vger.kernel.org
+Description:
+ Averaged raw measurement from channel X. The number of values
+ used for averaging is device specific. The converting rules for
+ normal raw values also applies to the averaged raw values.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_voltage_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_i_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_q_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_voltage_q_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_voltage_i_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_currentY_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_current_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_currentY_i_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_currentY_q_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_current_q_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_current_i_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_tempY_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_temp_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_pressure_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_humidityrelative_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_offset
+What: /sys/bus/iio/devices/iio:deviceX/in_angl_offset
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ If known for a device, offset to be added to <type>[Y]_raw prior
+ to scaling by <type>[Y]_scale in order to obtain value in the
+ <type> units as specified in <type>[Y]_raw documentation.
+ Not present if the offset is always 0 or unknown. If Y or
+ axis <x|y|z> is not present, then the offset applies to all
+ in channels of <type>.
+ May be writable if a variable offset can be applied on the
+ device. Note that this is different to calibbias which
+ is for devices (or drivers) that apply offsets to compensate
+ for variation between different instances of the part, typically
+ adjusted by using some hardware supported calibration procedure.
+ Calibbias is applied internally, offset is applied in userspace
+ to the _raw output.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_i_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_q_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_voltage_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_voltage_i_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_voltage_q_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_voltage-voltage_scale
+What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_scale
+What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_currentY_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_currentY_supply_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_current_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_currentY_i_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_currentY_q_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_current_i_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_current_q_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_peak_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_energy_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_distance_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_z_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_from_north_magnetic_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_from_north_true_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_from_north_magnetic_tilt_comp_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_from_north_true_tilt_comp_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_pressure_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_humidityrelative_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_illuminance_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_scale
+What: /sys/bus/iio/devices/iio:deviceX/in_angl_scale
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ If known for a device, scale to be applied to <type>Y[_name]_raw
+ post addition of <type>[Y][_name]_offset in order to obtain the
+ measured value in <type> units as specified in
+ <type>[Y][_name]_raw documentation. If shared across all in
+ channels then Y and <x|y|z> are not present and the value is
+ called <type>[Y][_name]_scale. The peak modifier means this
+ value is applied to <type>Y[_name]_peak_raw values.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibbias
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibbias
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_calibbias
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_calibbias
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_calibbias
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_calibbias
+What: /sys/bus/iio/devices/iio:deviceX/in_illuminance0_calibbias
+What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibbias
+What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibbias
+What: /sys/bus/iio/devices/iio:deviceX/in_pressure_calibbias
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Hardware applied calibration offset (assumed to fix production
+ inaccuracies).
+
+What /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_voltageY_i_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_voltageY_q_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_voltage_i_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_voltage_q_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_voltage_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_accel_z_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_calibscale
+What /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_calibscale
+what /sys/bus/iio/devices/iio:deviceX/in_illuminance0_calibscale
+what /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibscale
+What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibscale
+What: /sys/bus/iio/devices/iio:deviceX/in_pressure_calibscale
+What: /sys/bus/iio/devices/iio:deviceX/in_illuminance_calibscale
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Hardware applied calibration scale factor (assumed to fix
+ production inaccuracies). If shared across all channels,
+ <type>_calibscale is used.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_activity_calibgender
+What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibgender
+What: /sys/bus/iio/devices/iio:deviceX/in_distance_calibgender
+What: /sys/bus/iio/devices/iio:deviceX/in_velocity_calibgender
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Gender of the user (e.g.: male, female) used by some pedometers
+ to compute the stride length, distance, speed and activity
+ type.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_activity_calibgender_available
+What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibgender_available
+What: /sys/bus/iio/devices/iio:deviceX/in_distance_calibgender_available
+What: /sys/bus/iio/devices/iio:deviceX/in_velocity_calibgender_available
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Lists all available gender values (e.g.: male, female).
+
+What: /sys/bus/iio/devices/iio:deviceX/in_activity_calibheight
+What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibheight
+What: /sys/bus/iio/devices/iio:deviceX/in_distance_calibheight
+What: /sys/bus/iio/devices/iio:deviceX/in_velocity_calibheight
+KernelVersion: 3.19
+Contact: linux-iio@vger.kernel.org
+Description:
+ Height of the user (in meters) used by some pedometers
+ to compute the stride length, distance, speed and activity
+ type.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibweight
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Weight of the user (in kg). It is needed by some pedometers
+ to compute the calories burnt by the user.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_scale_available
+What: /sys/.../iio:deviceX/in_anglvel_scale_available
+What: /sys/.../iio:deviceX/in_magn_scale_available
+What: /sys/.../iio:deviceX/in_illuminance_scale_available
+What: /sys/.../iio:deviceX/in_intensity_scale_available
+What: /sys/.../iio:deviceX/in_proximity_scale_available
+What: /sys/.../iio:deviceX/in_voltageX_scale_available
+What: /sys/.../iio:deviceX/in_voltage-voltage_scale_available
+What: /sys/.../iio:deviceX/out_voltageX_scale_available
+What: /sys/.../iio:deviceX/out_altvoltageX_scale_available
+What: /sys/.../iio:deviceX/in_capacitance_scale_available
+What: /sys/.../iio:deviceX/in_pressure_scale_available
+What: /sys/.../iio:deviceX/in_pressureY_scale_available
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ If a discrete set of scale values is available, they
+ are listed in this attribute.
+
+What /sys/bus/iio/devices/iio:deviceX/out_voltageY_hardwaregain
+What: /sys/bus/iio/devices/iio:deviceX/in_intensity_red_hardwaregain
+What: /sys/bus/iio/devices/iio:deviceX/in_intensity_green_hardwaregain
+What: /sys/bus/iio/devices/iio:deviceX/in_intensity_blue_hardwaregain
+What: /sys/bus/iio/devices/iio:deviceX/in_intensity_clear_hardwaregain
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Hardware applied gain factor. If shared across all channels,
+ <type>_hardwaregain is used.
+
+What: /sys/.../in_accel_filter_low_pass_3db_frequency
+What: /sys/.../in_magn_filter_low_pass_3db_frequency
+What: /sys/.../in_anglvel_filter_low_pass_3db_frequency
+KernelVersion: 3.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ If a known or controllable low pass filter is applied
+ to the underlying data channel, then this parameter
+ gives the 3dB frequency of the filter in Hz.
+
+What: /sys/.../in_accel_filter_high_pass_3db_frequency
+What: /sys/.../in_anglvel_filter_high_pass_3db_frequency
+What: /sys/.../in_magn_filter_high_pass_3db_frequency
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ If a known or controllable high pass filter is applied
+ to the underlying data channel, then this parameter
+ gives the 3dB frequency of the filter in Hz.
+
+What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw
+What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_raw
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled, no bias etc.) output voltage for
+ channel Y. The number must always be specified and
+ unique if the output corresponds to a single channel.
+ While DAC like devices typically use out_voltage,
+ a continuous frequency generating device, such as
+ a DDS or PLL should use out_altvoltage.
+
+What: /sys/bus/iio/devices/iio:deviceX/out_voltageY&Z_raw
+What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY&Z_raw
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled, no bias etc.) output voltage for an aggregate of
+ channel Y, channel Z, etc. This interface is available in cases
+ where a single output sets the value for multiple channels
+ simultaneously.
+
+What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown_mode
+What: /sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown_mode
+What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown_mode
+What: /sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown_mode
+KernelVersion: 2.6.38
+Contact: linux-iio@vger.kernel.org
+Description:
+ Specifies the output powerdown mode.
+ DAC output stage is disconnected from the amplifier and
+ 1kohm_to_gnd: connected to ground via an 1kOhm resistor,
+ 2.5kohm_to_gnd: connected to ground via a 2.5kOhm resistor,
+ 6kohm_to_gnd: connected to ground via a 6kOhm resistor,
+ 20kohm_to_gnd: connected to ground via a 20kOhm resistor,
+ 90kohm_to_gnd: connected to ground via a 90kOhm resistor,
+ 100kohm_to_gnd: connected to ground via an 100kOhm resistor,
+ 125kohm_to_gnd: connected to ground via an 125kOhm resistor,
+ 500kohm_to_gnd: connected to ground via a 500kOhm resistor,
+ 640kohm_to_gnd: connected to ground via a 640kOhm resistor,
+ three_state: left floating.
+ For a list of available output power down options read
+ outX_powerdown_mode_available. If Y is not present the
+ mode is shared across all outputs.
+
+What: /sys/.../iio:deviceX/out_voltageY_powerdown_mode_available
+What: /sys/.../iio:deviceX/out_voltage_powerdown_mode_available
+What: /sys/.../iio:deviceX/out_altvoltageY_powerdown_mode_available
+What: /sys/.../iio:deviceX/out_altvoltage_powerdown_mode_available
+KernelVersion: 2.6.38
+Contact: linux-iio@vger.kernel.org
+Description:
+ Lists all available output power down modes.
+ If Y is not present the mode is shared across all outputs.
+
+What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown
+What: /sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown
+What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown
+What: /sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown
+KernelVersion: 2.6.38
+Contact: linux-iio@vger.kernel.org
+Description:
+ Writing 1 causes output Y to enter the power down mode specified
+ by the corresponding outY_powerdown_mode. DAC output stage is
+ disconnected from the amplifier. Clearing returns to normal
+ operation. Y may be suppressed if all outputs are controlled
+ together.
+
+What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_frequency
+KernelVersion: 3.4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Output frequency for channel Y in Hz. The number must always be
+ specified and unique if the output corresponds to a single
+ channel.
+
+What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_phase
+KernelVersion: 3.4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Phase in radians of one frequency/clock output Y
+ (out_altvoltageY) relative to another frequency/clock output
+ (out_altvoltageZ) of the device X. The number must always be
+ specified and unique if the output corresponds to a single
+ channel.
+
+What: /sys/bus/iio/devices/iio:deviceX/events
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Configuration of which hardware generated events are passed up
+ to user-space.
+
+What: /sys/.../iio:deviceX/events/in_accel_x_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_x_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_accel_y_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_y_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_accel_z_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_z_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_anglvel_x_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_anglvel_x_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_anglvel_y_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_anglvel_y_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_anglvel_z_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_anglvel_z_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_magn_x_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_magn_x_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_magn_y_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_magn_y_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_magn_z_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_magn_z_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_magnetic_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_magnetic_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_true_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_true_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_magnetic_tilt_comp_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_magnetic_tilt_comp_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_true_tilt_comp_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_true_tilt_comp_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_voltageY_supply_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_voltageY_supply_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_voltageY_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_voltageY_thresh_falling_en
+What: /sys/.../iio:deviceX/events/in_voltageY_thresh_either_en
+What: /sys/.../iio:deviceX/events/in_tempY_thresh_rising_en
+What: /sys/.../iio:deviceX/events/in_tempY_thresh_falling_en
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Event generated when channel passes a threshold in the specified
+ (_rising|_falling) direction. If the direction is not specified,
+ then either the device will report an event which ever direction
+ a single threshold value is passed in (e.g.
+ <type>[Y][_name]_<raw|input>_thresh_value) or
+ <type>[Y][_name]_<raw|input>_thresh_rising_value and
+ <type>[Y][_name]_<raw|input>_thresh_falling_value may take
+ different values, but the device can only enable both thresholds
+ or neither.
+ Note the driver will assume the last p events requested are
+ to be enabled where p is how many it supports (which may vary
+ depending on the exact set requested. So if you want to be
+ sure you have set what you think you have, check the contents of
+ these attributes after everything is configured. Drivers may
+ have to buffer any parameters so that they are consistent when
+ a given event type is enabled at a future point (and not those for
+ whatever event was previously enabled).
+
+What: /sys/.../iio:deviceX/events/in_accel_x_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_x_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_accel_y_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_y_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_accel_z_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_z_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_anglvel_x_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_anglvel_x_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_anglvel_y_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_anglvel_y_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_anglvel_z_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_anglvel_z_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_magn_x_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_magn_x_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_magn_y_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_magn_y_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_magn_z_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_magn_z_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_magnetic_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_magnetic_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_true_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_true_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_magnetic_tilt_comp_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_magnetic_tilt_comp_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_true_tilt_comp_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_rot_from_north_true_tilt_comp_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_voltageY_supply_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_voltageY_supply_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_voltageY_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_voltageY_roc_falling_en
+What: /sys/.../iio:deviceX/events/in_tempY_roc_rising_en
+What: /sys/.../iio:deviceX/events/in_tempY_roc_falling_en
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Event generated when channel passes a threshold on the rate of
+ change (1st differential) in the specified (_rising|_falling)
+ direction. If the direction is not specified, then either the
+ device will report an event which ever direction a single
+ threshold value is passed in (e.g.
+ <type>[Y][_name]_<raw|input>_roc_value) or
+ <type>[Y][_name]_<raw|input>_roc_rising_value and
+ <type>[Y][_name]_<raw|input>_roc_falling_value may take
+ different values, but the device can only enable both rate of
+ change thresholds or neither.
+ Note the driver will assume the last p events requested are
+ to be enabled where p is however many it supports (which may
+ vary depending on the exact set requested. So if you want to be
+ sure you have set what you think you have, check the contents of
+ these attributes after everything is configured. Drivers may
+ have to buffer any parameters so that they are consistent when
+ a given event type is enabled a future point (and not those for
+ whatever event was previously enabled).
+
+What: /sys/.../events/in_accel_thresh_rising_value
+What: /sys/.../events/in_accel_thresh_falling_value
+What: /sys/.../events/in_accel_x_raw_thresh_rising_value
+What: /sys/.../events/in_accel_x_raw_thresh_falling_value
+What: /sys/.../events/in_accel_y_raw_thresh_rising_value
+What: /sys/.../events/in_accel_y_raw_thresh_falling_value
+What: /sys/.../events/in_accel_z_raw_thresh_rising_value
+What: /sys/.../events/in_accel_z_raw_thresh_falling_value
+What: /sys/.../events/in_anglvel_x_raw_thresh_rising_value
+What: /sys/.../events/in_anglvel_x_raw_thresh_falling_value
+What: /sys/.../events/in_anglvel_y_raw_thresh_rising_value
+What: /sys/.../events/in_anglvel_y_raw_thresh_falling_value
+What: /sys/.../events/in_anglvel_z_raw_thresh_rising_value
+What: /sys/.../events/in_anglvel_z_raw_thresh_falling_value
+What: /sys/.../events/in_magn_x_raw_thresh_rising_value
+What: /sys/.../events/in_magn_x_raw_thresh_falling_value
+What: /sys/.../events/in_magn_y_raw_thresh_rising_value
+What: /sys/.../events/in_magn_y_raw_thresh_falling_value
+What: /sys/.../events/in_magn_z_raw_thresh_rising_value
+What: /sys/.../events/in_magn_z_raw_thresh_falling_value
+What: /sys/.../events/in_rot_from_north_magnetic_raw_thresh_rising_value
+What: /sys/.../events/in_rot_from_north_magnetic_raw_thresh_falling_value
+What: /sys/.../events/in_rot_from_north_true_raw_thresh_rising_value
+What: /sys/.../events/in_rot_from_north_true_raw_thresh_falling_value
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_raw_thresh_rising_value
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_raw_thresh_falling_value
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_raw_thresh_rising_value
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_raw_thresh_falling_value
+What: /sys/.../events/in_voltageY_supply_raw_thresh_rising_value
+What: /sys/.../events/in_voltageY_supply_raw_thresh_falling_value
+What: /sys/.../events/in_voltageY_raw_thresh_rising_value
+What: /sys/.../events/in_voltageY_raw_thresh_falling_value
+What: /sys/.../events/in_tempY_raw_thresh_rising_value
+What: /sys/.../events/in_tempY_raw_thresh_falling_value
+What: /sys/.../events/in_illuminance0_thresh_falling_value
+what: /sys/.../events/in_illuminance0_thresh_rising_value
+what: /sys/.../events/in_proximity0_thresh_falling_value
+what: /sys/.../events/in_proximity0_thresh_rising_value
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Specifies the value of threshold that the device is comparing
+ against for the events enabled by
+ <type>Y[_name]_thresh[_rising|falling]_en.
+ If separate attributes exist for the two directions, but
+ direction is not specified for this attribute, then a single
+ threshold value applies to both directions.
+ The raw or input element of the name indicates whether the
+ value is in raw device units or in processed units (as _raw
+ and _input do on sysfs direct channel read attributes).
+
+What: /sys/.../events/in_accel_scale
+What: /sys/.../events/in_accel_peak_scale
+What: /sys/.../events/in_anglvel_scale
+What: /sys/.../events/in_magn_scale
+What: /sys/.../events/in_rot_from_north_magnetic_scale
+What: /sys/.../events/in_rot_from_north_true_scale
+What: /sys/.../events/in_voltage_scale
+What: /sys/.../events/in_voltage_supply_scale
+What: /sys/.../events/in_temp_scale
+What: /sys/.../events/in_illuminance_scale
+What: /sys/.../events/in_proximity_scale
+KernelVersion: 3.21
+Contact: linux-iio@vger.kernel.org
+Description:
+ Specifies the conversion factor from the standard units
+ to device specific units used to set the event trigger
+ threshold.
+
+What: /sys/.../events/in_accel_x_thresh_rising_hysteresis
+What: /sys/.../events/in_accel_x_thresh_falling_hysteresis
+What: /sys/.../events/in_accel_x_thresh_either_hysteresis
+What: /sys/.../events/in_accel_y_thresh_rising_hysteresis
+What: /sys/.../events/in_accel_y_thresh_falling_hysteresis
+What: /sys/.../events/in_accel_y_thresh_either_hysteresis
+What: /sys/.../events/in_accel_z_thresh_rising_hysteresis
+What: /sys/.../events/in_accel_z_thresh_falling_hysteresis
+What: /sys/.../events/in_accel_z_thresh_either_hysteresis
+What: /sys/.../events/in_anglvel_x_thresh_rising_hysteresis
+What: /sys/.../events/in_anglvel_x_thresh_falling_hysteresis
+What: /sys/.../events/in_anglvel_x_thresh_either_hysteresis
+What: /sys/.../events/in_anglvel_y_thresh_rising_hysteresis
+What: /sys/.../events/in_anglvel_y_thresh_falling_hysteresis
+What: /sys/.../events/in_anglvel_y_thresh_either_hysteresis
+What: /sys/.../events/in_anglvel_z_thresh_rising_hysteresis
+What: /sys/.../events/in_anglvel_z_thresh_falling_hysteresis
+What: /sys/.../events/in_anglvel_z_thresh_either_hysteresis
+What: /sys/.../events/in_magn_x_thresh_rising_hysteresis
+What: /sys/.../events/in_magn_x_thresh_falling_hysteresis
+What: /sys/.../events/in_magn_x_thresh_either_hysteresis
+What: /sys/.../events/in_magn_y_thresh_rising_hysteresis
+What: /sys/.../events/in_magn_y_thresh_falling_hysteresis
+What: /sys/.../events/in_magn_y_thresh_either_hysteresis
+What: /sys/.../events/in_magn_z_thresh_rising_hysteresis
+What: /sys/.../events/in_magn_z_thresh_falling_hysteresis
+What: /sys/.../events/in_magn_z_thresh_either_hysteresis
+What: /sys/.../events/in_rot_from_north_magnetic_thresh_rising_hysteresis
+What: /sys/.../events/in_rot_from_north_magnetic_thresh_falling_hysteresis
+What: /sys/.../events/in_rot_from_north_magnetic_thresh_either_hysteresis
+What: /sys/.../events/in_rot_from_north_true_thresh_rising_hysteresis
+What: /sys/.../events/in_rot_from_north_true_thresh_falling_hysteresis
+What: /sys/.../events/in_rot_from_north_true_thresh_either_hysteresis
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_thresh_rising_hysteresis
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_thresh_falling_hysteresis
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_thresh_either_hysteresis
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_thresh_rising_hysteresis
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_thresh_falling_hysteresis
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_thresh_either_hysteresis
+What: /sys/.../events/in_voltageY_thresh_rising_hysteresis
+What: /sys/.../events/in_voltageY_thresh_falling_hysteresis
+What: /sys/.../events/in_voltageY_thresh_either_hysteresis
+What: /sys/.../events/in_tempY_thresh_rising_hysteresis
+What: /sys/.../events/in_tempY_thresh_falling_hysteresis
+What: /sys/.../events/in_tempY_thresh_either_hysteresis
+What: /sys/.../events/in_illuminance0_thresh_falling_hysteresis
+what: /sys/.../events/in_illuminance0_thresh_rising_hysteresis
+what: /sys/.../events/in_illuminance0_thresh_either_hysteresis
+what: /sys/.../events/in_proximity0_thresh_falling_hysteresis
+what: /sys/.../events/in_proximity0_thresh_rising_hysteresis
+what: /sys/.../events/in_proximity0_thresh_either_hysteresis
+KernelVersion: 3.13
+Contact: linux-iio@vger.kernel.org
+Description:
+ Specifies the hysteresis of threshold that the device is comparing
+ against for the events enabled by
+ <type>Y[_name]_thresh[_(rising|falling)]_hysteresis.
+ If separate attributes exist for the two directions, but
+ direction is not specified for this attribute, then a single
+ hysteresis value applies to both directions.
+ For falling events the hysteresis is added to the _value attribute for
+ this event to get the upper threshold for when the event goes back to
+ normal, for rising events the hysteresis is subtracted from the _value
+ attribute. E.g. if in_voltage0_raw_thresh_rising_value is set to 1200
+ and in_voltage0_raw_thresh_rising_hysteresis is set to 50. The event
+ will get activated once in_voltage0_raw goes above 1200 and will become
+ deactivated again once the value falls below 1150.
+
+What: /sys/.../events/in_accel_x_raw_roc_rising_value
+What: /sys/.../events/in_accel_x_raw_roc_falling_value
+What: /sys/.../events/in_accel_y_raw_roc_rising_value
+What: /sys/.../events/in_accel_y_raw_roc_falling_value
+What: /sys/.../events/in_accel_z_raw_roc_rising_value
+What: /sys/.../events/in_accel_z_raw_roc_falling_value
+What: /sys/.../events/in_anglvel_x_raw_roc_rising_value
+What: /sys/.../events/in_anglvel_x_raw_roc_falling_value
+What: /sys/.../events/in_anglvel_y_raw_roc_rising_value
+What: /sys/.../events/in_anglvel_y_raw_roc_falling_value
+What: /sys/.../events/in_anglvel_z_raw_roc_rising_value
+What: /sys/.../events/in_anglvel_z_raw_roc_falling_value
+What: /sys/.../events/in_magn_x_raw_roc_rising_value
+What: /sys/.../events/in_magn_x_raw_roc_falling_value
+What: /sys/.../events/in_magn_y_raw_roc_rising_value
+What: /sys/.../events/in_magn_y_raw_roc_falling_value
+What: /sys/.../events/in_magn_z_raw_roc_rising_value
+What: /sys/.../events/in_magn_z_raw_roc_falling_value
+What: /sys/.../events/in_rot_from_north_magnetic_raw_roc_rising_value
+What: /sys/.../events/in_rot_from_north_magnetic_raw_roc_falling_value
+What: /sys/.../events/in_rot_from_north_true_raw_roc_rising_value
+What: /sys/.../events/in_rot_from_north_true_raw_roc_falling_value
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_raw_roc_rising_value
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_raw_roc_falling_value
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_raw_roc_rising_value
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_raw_roc_falling_value
+What: /sys/.../events/in_voltageY_supply_raw_roc_rising_value
+What: /sys/.../events/in_voltageY_supply_raw_roc_falling_value
+What: /sys/.../events/in_voltageY_raw_roc_rising_value
+What: /sys/.../events/in_voltageY_raw_roc_falling_value
+What: /sys/.../events/in_tempY_raw_roc_rising_value
+What: /sys/.../events/in_tempY_raw_roc_falling_value
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Specifies the value of rate of change threshold that the
+ device is comparing against for the events enabled by
+ <type>[Y][_name]_roc[_rising|falling]_en.
+ If separate attributes exist for the two directions,
+ but direction is not specified for this attribute,
+ then a single threshold value applies to both directions.
+ The raw or input element of the name indicates whether the
+ value is in raw device units or in processed units (as _raw
+ and _input do on sysfs direct channel read attributes).
+
+What: /sys/.../events/in_accel_x_thresh_rising_period
+What: /sys/.../events/in_accel_x_thresh_falling_period
+What: /sys/.../events/in_accel_x_roc_rising_period
+What: /sys/.../events/in_accel_x_roc_falling_period
+What: /sys/.../events/in_accel_y_thresh_rising_period
+What: /sys/.../events/in_accel_y_thresh_falling_period
+What: /sys/.../events/in_accel_y_roc_rising_period
+What: /sys/.../events/in_accel_y_roc_falling_period
+What: /sys/.../events/in_accel_z_thresh_rising_period
+What: /sys/.../events/in_accel_z_thresh_falling_period
+What: /sys/.../events/in_accel_z_roc_rising_period
+What: /sys/.../events/in_accel_z_roc_falling_period
+What: /sys/.../events/in_anglvel_x_thresh_rising_period
+What: /sys/.../events/in_anglvel_x_thresh_falling_period
+What: /sys/.../events/in_anglvel_x_roc_rising_period
+What: /sys/.../events/in_anglvel_x_roc_falling_period
+What: /sys/.../events/in_anglvel_y_thresh_rising_period
+What: /sys/.../events/in_anglvel_y_thresh_falling_period
+What: /sys/.../events/in_anglvel_y_roc_rising_period
+What: /sys/.../events/in_anglvel_y_roc_falling_period
+What: /sys/.../events/in_anglvel_z_thresh_rising_period
+What: /sys/.../events/in_anglvel_z_thresh_falling_period
+What: /sys/.../events/in_anglvel_z_roc_rising_period
+What: /sys/.../events/in_anglvel_z_roc_falling_period
+What: /sys/.../events/in_magn_x_thresh_rising_period
+What: /sys/.../events/in_magn_x_thresh_falling_period
+What: /sys/.../events/in_magn_x_roc_rising_period
+What: /sys/.../events/in_magn_x_roc_falling_period
+What: /sys/.../events/in_magn_y_thresh_rising_period
+What: /sys/.../events/in_magn_y_thresh_falling_period
+What: /sys/.../events/in_magn_y_roc_rising_period
+What: /sys/.../events/in_magn_y_roc_falling_period
+What: /sys/.../events/in_magn_z_thresh_rising_period
+What: /sys/.../events/in_magn_z_thresh_falling_period
+What: /sys/.../events/in_magn_z_roc_rising_period
+What: /sys/.../events/in_magn_z_roc_falling_period
+What: /sys/.../events/in_rot_from_north_magnetic_thresh_rising_period
+What: /sys/.../events/in_rot_from_north_magnetic_thresh_falling_period
+What: /sys/.../events/in_rot_from_north_magnetic_roc_rising_period
+What: /sys/.../events/in_rot_from_north_magnetic_roc_falling_period
+What: /sys/.../events/in_rot_from_north_true_thresh_rising_period
+What: /sys/.../events/in_rot_from_north_true_thresh_falling_period
+What: /sys/.../events/in_rot_from_north_true_roc_rising_period
+What: /sys/.../events/in_rot_from_north_true_roc_falling_period
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_thresh_rising_period
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_thresh_falling_period
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_roc_rising_period
+What: /sys/.../events/in_rot_from_north_magnetic_tilt_comp_roc_falling_period
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_thresh_rising_period
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_thresh_falling_period
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_roc_rising_period
+What: /sys/.../events/in_rot_from_north_true_tilt_comp_roc_falling_period
+What: /sys/.../events/in_voltageY_supply_thresh_rising_period
+What: /sys/.../events/in_voltageY_supply_thresh_falling_period
+What: /sys/.../events/in_voltageY_supply_roc_rising_period
+What: /sys/.../events/in_voltageY_supply_roc_falling_period
+What: /sys/.../events/in_voltageY_thresh_rising_period
+What: /sys/.../events/in_voltageY_thresh_falling_period
+What: /sys/.../events/in_voltageY_roc_rising_period
+What: /sys/.../events/in_voltageY_roc_falling_period
+What: /sys/.../events/in_tempY_thresh_rising_period
+What: /sys/.../events/in_tempY_thresh_falling_period
+What: /sys/.../events/in_tempY_roc_rising_period
+What: /sys/.../events/in_tempY_roc_falling_period
+What: /sys/.../events/in_accel_x&y&z_mag_falling_period
+What: /sys/.../events/in_intensity0_thresh_period
+What: /sys/.../events/in_proximity0_thresh_period
+What: /sys/.../events/in_activity_still_thresh_rising_period
+What: /sys/.../events/in_activity_still_thresh_falling_period
+What: /sys/.../events/in_activity_walking_thresh_rising_period
+What: /sys/.../events/in_activity_walking_thresh_falling_period
+What: /sys/.../events/in_activity_jogging_thresh_rising_period
+What: /sys/.../events/in_activity_jogging_thresh_falling_period
+What: /sys/.../events/in_activity_running_thresh_rising_period
+What: /sys/.../events/in_activity_running_thresh_falling_period
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Period of time (in seconds) for which the condition must be
+ met before an event is generated. If direction is not
+ specified then this period applies to both directions.
+
+What: /sys/.../events/in_accel_thresh_rising_low_pass_filter_3db
+What: /sys/.../events/in_anglvel_thresh_rising_low_pass_filter_3db
+What: /sys/.../events/in_magn_thresh_rising_low_pass_filter_3db
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ If a low pass filter can be applied to the event generation
+ this property gives its 3db frequency in Hz.
+ A value of zero disables the filter.
+
+What: /sys/.../events/in_accel_thresh_rising_high_pass_filter_3db
+What: /sys/.../events/in_anglvel_thresh_rising_high_pass_filter_3db
+What: /sys/.../events/in_magn_thresh_rising_high_pass_filter_3db
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ If a high pass filter can be applied to the event generation
+ this property gives its 3db frequency in Hz.
+ A value of zero disables the filter.
+
+What: /sys/.../events/in_activity_still_thresh_rising_en
+What: /sys/.../events/in_activity_still_thresh_falling_en
+What: /sys/.../events/in_activity_walking_thresh_rising_en
+What: /sys/.../events/in_activity_walking_thresh_falling_en
+What: /sys/.../events/in_activity_jogging_thresh_rising_en
+What: /sys/.../events/in_activity_jogging_thresh_falling_en
+What: /sys/.../events/in_activity_running_thresh_rising_en
+What: /sys/.../events/in_activity_running_thresh_falling_en
+KernelVersion: 3.19
+Contact: linux-iio@vger.kernel.org
+Description:
+ Enables or disables activitity events. Depending on direction
+ an event is generated when sensor ENTERS or LEAVES a given state.
+
+What: /sys/.../events/in_activity_still_thresh_rising_value
+What: /sys/.../events/in_activity_still_thresh_falling_value
+What: /sys/.../events/in_activity_walking_thresh_rising_value
+What: /sys/.../events/in_activity_walking_thresh_falling_value
+What: /sys/.../events/in_activity_jogging_thresh_rising_value
+What: /sys/.../events/in_activity_jogging_thresh_falling_value
+What: /sys/.../events/in_activity_running_thresh_rising_value
+What: /sys/.../events/in_activity_running_thresh_falling_value
+KernelVersion: 3.19
+Contact: linux-iio@vger.kernel.org
+Description:
+ Confidence value (in units as percentage) to be used
+ for deciding when an event should be generated. E.g for
+ running: If the confidence value reported by the sensor
+ is greater than in_activity_running_thresh_rising_value
+ then the sensor ENTERS running state. Conversely, if the
+ confidence value reported by the sensor is lower than
+ in_activity_running_thresh_falling_value then the sensor
+ is LEAVING running state.
+
+What: /sys/.../iio:deviceX/events/in_accel_mag_en
+What: /sys/.../iio:deviceX/events/in_accel_mag_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_mag_falling_en
+What: /sys/.../iio:deviceX/events/in_accel_x_mag_en
+What: /sys/.../iio:deviceX/events/in_accel_x_mag_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_x_mag_falling_en
+What: /sys/.../iio:deviceX/events/in_accel_y_mag_en
+What: /sys/.../iio:deviceX/events/in_accel_y_mag_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_y_mag_falling_en
+What: /sys/.../iio:deviceX/events/in_accel_z_mag_en
+What: /sys/.../iio:deviceX/events/in_accel_z_mag_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_z_mag_falling_en
+What: /sys/.../iio:deviceX/events/in_accel_x&y&z_mag_rising_en
+What: /sys/.../iio:deviceX/events/in_accel_x&y&z_mag_falling_en
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Similar to in_accel_x_thresh[_rising|_falling]_en, but here the
+ magnitude of the channel is compared to the threshold, not its
+ signed value.
+
+What: /sys/.../events/in_accel_raw_mag_value
+What: /sys/.../events/in_accel_x_raw_mag_rising_value
+What: /sys/.../events/in_accel_y_raw_mag_rising_value
+What: /sys/.../events/in_accel_z_raw_mag_rising_value
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ The value to which the magnitude of the channel is compared. If
+ number or direction is not specified, applies to all channels of
+ this type.
+
+What: /sys/.../events/in_steps_change_en
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Event generated when channel passes a threshold on the absolute
+ change in value. E.g. for steps: a step change event is
+ generated each time the user takes N steps, where N is set using
+ in_steps_change_value.
+
+What: /sys/.../events/in_steps_change_value
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Specifies the value of change threshold that the
+ device is comparing against for the events enabled by
+ <type>[Y][_name]_roc[_rising|falling|]_en. E.g. for steps:
+ if set to 3, a step change event will be generated every 3
+ steps.
+
+What: /sys/bus/iio/devices/iio:deviceX/trigger/current_trigger
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ The name of the trigger source being used, as per string given
+ in /sys/class/iio/triggerY/name.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer/length
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Number of scans contained by the buffer.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer/enable
+KernelVersion: 2.6.35
+Contact: linux-iio@vger.kernel.org
+Description:
+ Actually start the buffer capture up. Will start trigger
+ if first device and appropriate.
+
+What: /sys/bus/iio/devices/iio:deviceX/scan_elements
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Directory containing interfaces for elements that will be
+ captured for a single triggered sample set in the buffer.
+
+What: /sys/.../iio:deviceX/scan_elements/in_accel_x_en
+What: /sys/.../iio:deviceX/scan_elements/in_accel_y_en
+What: /sys/.../iio:deviceX/scan_elements/in_accel_z_en
+What: /sys/.../iio:deviceX/scan_elements/in_anglvel_x_en
+What: /sys/.../iio:deviceX/scan_elements/in_anglvel_y_en
+What: /sys/.../iio:deviceX/scan_elements/in_anglvel_z_en
+What: /sys/.../iio:deviceX/scan_elements/in_magn_x_en
+What: /sys/.../iio:deviceX/scan_elements/in_magn_y_en
+What: /sys/.../iio:deviceX/scan_elements/in_magn_z_en
+What: /sys/.../iio:deviceX/scan_elements/in_rot_from_north_magnetic_en
+What: /sys/.../iio:deviceX/scan_elements/in_rot_from_north_true_en
+What: /sys/.../iio:deviceX/scan_elements/in_rot_from_north_magnetic_tilt_comp_en
+What: /sys/.../iio:deviceX/scan_elements/in_rot_from_north_true_tilt_comp_en
+What: /sys/.../iio:deviceX/scan_elements/in_timestamp_en
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_supply_en
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_en
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY-voltageZ_en
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_i_en
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_q_en
+What: /sys/.../iio:deviceX/scan_elements/in_voltage_i_en
+What: /sys/.../iio:deviceX/scan_elements/in_voltage_q_en
+What: /sys/.../iio:deviceX/scan_elements/in_incli_x_en
+What: /sys/.../iio:deviceX/scan_elements/in_incli_y_en
+What: /sys/.../iio:deviceX/scan_elements/in_pressureY_en
+What: /sys/.../iio:deviceX/scan_elements/in_pressure_en
+What: /sys/.../iio:deviceX/scan_elements/in_rot_quaternion_en
+What: /sys/.../iio:deviceX/scan_elements/in_proximity_en
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Scan element control for triggered data capture.
+
+What: /sys/.../iio:deviceX/scan_elements/in_accel_type
+What: /sys/.../iio:deviceX/scan_elements/in_anglvel_type
+What: /sys/.../iio:deviceX/scan_elements/in_magn_type
+What: /sys/.../iio:deviceX/scan_elements/in_incli_type
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_type
+What: /sys/.../iio:deviceX/scan_elements/in_voltage_type
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_supply_type
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_i_type
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_q_type
+What: /sys/.../iio:deviceX/scan_elements/in_voltage_i_type
+What: /sys/.../iio:deviceX/scan_elements/in_voltage_q_type
+What: /sys/.../iio:deviceX/scan_elements/in_timestamp_type
+What: /sys/.../iio:deviceX/scan_elements/in_pressureY_type
+What: /sys/.../iio:deviceX/scan_elements/in_pressure_type
+What: /sys/.../iio:deviceX/scan_elements/in_rot_quaternion_type
+What: /sys/.../iio:deviceX/scan_elements/in_proximity_type
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ Description of the scan element data storage within the buffer
+ and hence the form in which it is read from user-space.
+ Form is [be|le]:[s|u]bits/storagebits[>>shift].
+ be or le specifies big or little endian. s or u specifies if
+ signed (2's complement) or unsigned. bits is the number of bits
+ of data and storagebits is the space (after padding) that it
+ occupies in the buffer. shift if specified, is the shift that
+ needs to be applied prior to masking out unused bits. Some
+ devices put their data in the middle of the transferred elements
+ with additional information on both sides. Note that some
+ devices will have additional information in the unused bits
+ so to get a clean value, the bits value must be used to mask
+ the buffer output value appropriately. The storagebits value
+ also specifies the data alignment. So s48/64>>2 will be a
+ signed 48 bit integer stored in a 64 bit location aligned to
+ a 64 bit boundary. To obtain the clean value, shift right 2
+ and apply a mask to zero the top 16 bits of the result.
+ For other storage combinations this attribute will be extended
+ appropriately.
+
+What: /sys/.../iio:deviceX/scan_elements/in_accel_type_available
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ If the type parameter can take one of a small set of values,
+ this attribute lists them.
+
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_index
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_supply_index
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_i_index
+What: /sys/.../iio:deviceX/scan_elements/in_voltageY_q_index
+What: /sys/.../iio:deviceX/scan_elements/in_voltage_i_index
+What: /sys/.../iio:deviceX/scan_elements/in_voltage_q_index
+What: /sys/.../iio:deviceX/scan_elements/in_accel_x_index
+What: /sys/.../iio:deviceX/scan_elements/in_accel_y_index
+What: /sys/.../iio:deviceX/scan_elements/in_accel_z_index
+What: /sys/.../iio:deviceX/scan_elements/in_anglvel_x_index
+What: /sys/.../iio:deviceX/scan_elements/in_anglvel_y_index
+What: /sys/.../iio:deviceX/scan_elements/in_anglvel_z_index
+What: /sys/.../iio:deviceX/scan_elements/in_magn_x_index
+What: /sys/.../iio:deviceX/scan_elements/in_magn_y_index
+What: /sys/.../iio:deviceX/scan_elements/in_magn_z_index
+What: /sys/.../iio:deviceX/scan_elements/in_rot_from_north_magnetic_index
+What: /sys/.../iio:deviceX/scan_elements/in_rot_from_north_true_index
+What: /sys/.../iio:deviceX/scan_elements/in_rot_from_north_magnetic_tilt_comp_index
+What: /sys/.../iio:deviceX/scan_elements/in_rot_from_north_true_tilt_comp_index
+What: /sys/.../iio:deviceX/scan_elements/in_incli_x_index
+What: /sys/.../iio:deviceX/scan_elements/in_incli_y_index
+What: /sys/.../iio:deviceX/scan_elements/in_timestamp_index
+What: /sys/.../iio:deviceX/scan_elements/in_pressureY_index
+What: /sys/.../iio:deviceX/scan_elements/in_pressure_index
+What: /sys/.../iio:deviceX/scan_elements/in_rot_quaternion_index
+What: /sys/.../iio:deviceX/scan_elements/in_proximity_index
+KernelVersion: 2.6.37
+Contact: linux-iio@vger.kernel.org
+Description:
+ A single positive integer specifying the position of this
+ scan element in the buffer. Note these are not dependent on
+ what is enabled and may not be contiguous. Thus for user-space
+ to establish the full layout these must be used in conjunction
+ with all _en attributes to establish which channels are present,
+ and the relevant _type attributes to establish the data storage
+ format.
+
+What: /sys/.../iio:deviceX/in_activity_still_input
+What: /sys/.../iio:deviceX/in_activity_walking_input
+What: /sys/.../iio:deviceX/in_activity_jogging_input
+What: /sys/.../iio:deviceX/in_activity_running_input
+KernelVersion: 3.19
+Contact: linux-iio@vger.kernel.org
+Description:
+ This attribute is used to read the confidence for an activity
+ expressed in units as percentage.
+
+What: /sys/.../iio:deviceX/in_anglvel_z_quadrature_correction_raw
+KernelVersion: 2.6.38
+Contact: linux-iio@vger.kernel.org
+Description:
+ This attribute is used to read the amount of quadrature error
+ present in the device at a given time.
+
+What: /sys/.../iio:deviceX/in_accelX_power_mode
+KernelVersion: 3.11
+Contact: linux-iio@vger.kernel.org
+Description:
+ Specifies the chip power mode.
+ low_noise: reduce noise level from ADC,
+ low_power: enable low current consumption.
+ For a list of available output power modes read
+ in_accel_power_mode_available.
+
+What: /sys/.../iio:deviceX/in_energy_input
+What: /sys/.../iio:deviceX/in_energy_raw
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ This attribute is used to read the energy value reported by the
+ device (e.g.: human activity sensors report energy burnt by the
+ user). Units after application of scale are Joules.
+
+What: /sys/.../iio:deviceX/in_distance_input
+What: /sys/.../iio:deviceX/in_distance_raw
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ This attribute is used to read the measured distance to an object
+ or the distance covered by the user since the last reboot while
+ activated. Units after application of scale are meters.
+
+What: /sys/bus/iio/devices/iio:deviceX/store_eeprom
+KernelVersion: 3.4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Writing '1' stores the current device configuration into
+ on-chip EEPROM. After power-up or chip reset the device will
+ automatically load the saved configuration.
+
+What: /sys/.../iio:deviceX/in_proximity_raw
+What: /sys/.../iio:deviceX/in_proximity_input
+What: /sys/.../iio:deviceX/in_proximityY_raw
+KernelVersion: 3.4
+Contact: linux-iio@vger.kernel.org
+Description:
+ Proximity measurement indicating that some
+ object is near the sensor, usually by observing
+ reflectivity of infrared or ultrasound emitted.
+ Often these sensors are unit less and as such conversion
+ to SI units is not possible. Higher proximity measurements
+ indicate closer objects, and vice versa. Units after
+ application of scale and offset are meters.
+
+What: /sys/.../iio:deviceX/in_illuminance_input
+What: /sys/.../iio:deviceX/in_illuminance_raw
+What: /sys/.../iio:deviceX/in_illuminanceY_input
+What: /sys/.../iio:deviceX/in_illuminanceY_raw
+What: /sys/.../iio:deviceX/in_illuminanceY_mean_raw
+What: /sys/.../iio:deviceX/in_illuminance_ir_raw
+What: /sys/.../iio:deviceX/in_illuminance_clear_raw
+KernelVersion: 3.4
+Contact: linux-iio@vger.kernel.org
+Description:
+ Illuminance measurement, units after application of scale
+ and offset are lux.
+
+What: /sys/.../iio:deviceX/in_intensityY_raw
+What: /sys/.../iio:deviceX/in_intensityY_ir_raw
+What: /sys/.../iio:deviceX/in_intensityY_both_raw
+What: /sys/.../iio:deviceX/in_intensityY_uv_raw
+What: /sys/.../iio:deviceX/in_intensityY_duv_raw
+KernelVersion: 3.4
+Contact: linux-iio@vger.kernel.org
+Description:
+ Unit-less light intensity. Modifiers both and ir indicate
+ that measurements contain visible and infrared light
+ components or just infrared light, respectively. Modifier
+ uv indicates that measurements contain ultraviolet light
+ components. Modifier duv indicates that measurements
+ contain deep ultraviolet light components.
+
+What: /sys/.../iio:deviceX/in_uvindex_input
+KernelVersion: 4.6
+Contact: linux-iio@vger.kernel.org
+Description:
+ UV light intensity index measuring the human skin's response to
+ different wavelength of sunlight weighted according to the
+ standardised CIE Erythemal Action Spectrum. UV index values range
+ from 0 (low) to >=11 (extreme).
+
+What: /sys/.../iio:deviceX/in_intensity_red_integration_time
+What: /sys/.../iio:deviceX/in_intensity_green_integration_time
+What: /sys/.../iio:deviceX/in_intensity_blue_integration_time
+What: /sys/.../iio:deviceX/in_intensity_clear_integration_time
+What: /sys/.../iio:deviceX/in_illuminance_integration_time
+KernelVersion: 3.12
+Contact: linux-iio@vger.kernel.org
+Description:
+ This attribute is used to get/set the integration time in
+ seconds.
+
+What: /sys/.../iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_integration_time
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Number of seconds in which to compute speed.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_quaternion_raw
+KernelVersion: 3.15
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw value of quaternion components using a format
+ x y z w. Here x, y, and z component represents the axis about
+ which a rotation will occur and w component represents the
+ amount of rotation.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_from_north_magnetic_tilt_comp_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_from_north_true_tilt_comp_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_from_north_magnetic_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_rot_from_north_true_raw
+KernelVersion: 3.15
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw value of rotation from true/magnetic north measured with
+ or without compensation from tilt sensors.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_currentX_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_currentX_i_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_currentX_q_raw
+KernelVersion: 3.18
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw current measurement from channel X. Units are in milliamps
+ after application of scale and offset. If no offset or scale is
+ present, output should be considered as processed with the
+ unit in milliamps.
+
+ Channels with 'i' and 'q' modifiers always exist in pairs and both
+ channels refer to the same signal. The 'i' channel contains the in-phase
+ component of the signal while the 'q' channel contains the quadrature
+ component.
+
+What: /sys/.../iio:deviceX/in_energy_en
+What: /sys/.../iio:deviceX/in_distance_en
+What: /sys/.../iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_en
+What: /sys/.../iio:deviceX/in_steps_en
+KernelVersion: 3.19
+Contact: linux-iio@vger.kernel.org
+Description:
+ Activates a device feature that runs in firmware/hardware.
+ E.g. for steps: the pedometer saves power while not used;
+ when activated, it will count the steps taken by the user in
+ firmware and export them through in_steps_input.
+
+What: /sys/.../iio:deviceX/in_steps_input
+KernelVersion: 3.19
+Contact: linux-iio@vger.kernel.org
+Description:
+ This attribute is used to read the number of steps taken by the user
+ since the last reboot while activated.
+
+What: /sys/.../iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_input
+What: /sys/.../iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_raw
+KernelVersion: 3.19
+Contact: linux-iio@vger.kernel.org
+Description:
+ This attribute is used to read the current speed value of the
+ user (which is the norm or magnitude of the velocity vector).
+ Units after application of scale are m/s.
+
+What: /sys/.../iio:deviceX/in_steps_debounce_count
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Specifies the number of steps that must occur within
+ in_steps_filter_debounce_time for the pedometer to decide the
+ consumer is making steps.
+
+What: /sys/.../iio:deviceX/in_steps_debounce_time
+KernelVersion: 4.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ Specifies number of seconds in which we compute the steps
+ that occur in order to decide if the consumer is making steps.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer/watermark
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ A single positive integer specifying the maximum number of scan
+ elements to wait for.
+ Poll will block until the watermark is reached.
+ Blocking read will wait until the minimum between the requested
+ read amount or the low water mark is available.
+ Non-blocking read will retrieve the available samples from the
+ buffer even if there are less samples then watermark level. This
+ allows the application to block on poll with a timeout and read
+ the available samples after the timeout expires and thus have a
+ maximum delay guarantee.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer/data_available
+KernelVersion: 4.16
+Contact: linux-iio@vger.kernel.org
+Description:
+ A read-only value indicating the bytes of data available in the
+ buffer. In the case of an output buffer, this indicates the
+ amount of empty space available to write data to. In the case of
+ an input buffer, this indicates the amount of data available for
+ reading.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer/hwfifo_enabled
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ A read-only boolean value that indicates if the hardware fifo is
+ currently enabled or disabled. If the device does not have a
+ hardware fifo this entry is not present.
+ The hardware fifo is enabled when the buffer is enabled if the
+ current hardware fifo watermark level is set and other current
+ device settings allows it (e.g. if a trigger is set that samples
+ data differently that the hardware fifo does then hardware fifo
+ will not enabled).
+ If the hardware fifo is enabled and the level of the hardware
+ fifo reaches the hardware fifo watermark level the device will
+ flush its hardware fifo to the device buffer. Doing a non
+ blocking read on the device when no samples are present in the
+ device buffer will also force a flush.
+ When the hardware fifo is enabled there is no need to use a
+ trigger to use buffer mode since the watermark settings
+ guarantees that the hardware fifo is flushed to the device
+ buffer.
+
+What: /sys/bus/iio/devices/iio:device*/buffer/hwfifo_timeout
+KernelVersion: 4.12
+Contact: linux-iio@vger.kernel.org
+Description:
+ A read/write property to provide capability to delay reporting of
+ samples till a timeout is reached. This allows host processors to
+ sleep, while the sensor is storing samples in its internal fifo.
+ The maximum timeout in seconds can be specified by setting
+ hwfifo_timeout.The current delay can be read by reading
+ hwfifo_timeout. A value of 0 means that there is no timeout.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer/hwfifo_watermark
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ Read-only entry that contains a single integer specifying the
+ current watermark level for the hardware fifo. If the device
+ does not have a hardware fifo this entry is not present.
+ The watermark level for the hardware fifo is set by the driver
+ based on the value set by the user in buffer/watermark but
+ taking into account hardware limitations (e.g. most hardware
+ buffers are limited to 32-64 samples, some hardware buffers
+ watermarks are fixed or have minimum levels). A value of 0
+ means that the hardware watermark is unset.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer/hwfifo_watermark_min
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ A single positive integer specifying the minimum watermark level
+ for the hardware fifo of this device. If the device does not
+ have a hardware fifo this entry is not present.
+ If the user sets buffer/watermark to a value less than this one,
+ then the hardware watermark will remain unset.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer/hwfifo_watermark_max
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ A single positive integer specifying the maximum watermark level
+ for the hardware fifo of this device. If the device does not
+ have a hardware fifo this entry is not present.
+ If the user sets buffer/watermark to a value greater than this
+ one, then the hardware watermark will be capped at this value.
+
+What: /sys/bus/iio/devices/iio:deviceX/buffer/hwfifo_watermark_available
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ A list of positive integers specifying the available watermark
+ levels for the hardware fifo. This entry is optional and if it
+ is not present it means that all the values between
+ hwfifo_watermark_min and hwfifo_watermark_max are supported.
+ If the user sets buffer/watermark to a value greater than
+ hwfifo_watermak_min but not equal to any of the values in this
+ list, the driver will chose an appropriate value for the
+ hardware fifo watermark level.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_temp_calibemissivity
+What: /sys/bus/iio/devices/iio:deviceX/in_tempX_calibemissivity
+What: /sys/bus/iio/devices/iio:deviceX/in_temp_object_calibemissivity
+What: /sys/bus/iio/devices/iio:deviceX/in_tempX_object_calibemissivity
+KernelVersion: 4.1
+Contact: linux-iio@vger.kernel.org
+Description:
+ The emissivity ratio of the surface in the field of view of the
+ contactless temperature sensor. Emissivity varies from 0 to 1,
+ with 1 being the emissivity of a black body.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_oversampling_ratio
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_oversampling_ratio
+What: /sys/bus/iio/devices/iio:deviceX/in_magn_z_oversampling_ratio
+KernelVersion: 4.2
+Contact: linux-iio@vger.kernel.org
+Description:
+ Hardware applied number of measurements for acquiring one
+ data point. The HW will do <type>[_name]_oversampling_ratio
+ measurements and return the average value as output data. Each
+ value resulted from <type>[_name]_oversampling_ratio measurements
+ is considered as one sample for <type>[_name]_sampling_frequency.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_concentration_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_concentrationX_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_concentration_co2_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_concentrationX_co2_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_concentration_voc_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_concentrationX_voc_raw
+KernelVersion: 4.3
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled no offset etc.) percentage reading of a substance.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_resistance_raw
+What: /sys/bus/iio/devices/iio:deviceX/in_resistanceX_raw
+What: /sys/bus/iio/devices/iio:deviceX/out_resistance_raw
+What: /sys/bus/iio/devices/iio:deviceX/out_resistanceX_raw
+KernelVersion: 4.3
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled no offset etc.) resistance reading that can be processed
+ into an ohm value.
+
+What: /sys/bus/iio/devices/iio:deviceX/heater_enable
+KernelVersion: 4.1.0
+Contact: linux-iio@vger.kernel.org
+Description:
+ '1' (enable) or '0' (disable) specifying the enable
+ of heater function. Same reading values apply
+ This ABI is especially applicable for humidity sensors
+ to heatup the device and get rid of any condensation
+ in some humidity environment
+
+What: /sys/bus/iio/devices/iio:deviceX/in_ph_raw
+KernelVersion: 4.5
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled no offset etc.) pH reading of a substance as a negative
+ base-10 logarithm of hydrodium ions in a litre of water.
+
+What: /sys/bus/iio/devices/iio:deviceX/mount_matrix
+What: /sys/bus/iio/devices/iio:deviceX/in_mount_matrix
+What: /sys/bus/iio/devices/iio:deviceX/out_mount_matrix
+What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_mount_matrix
+What: /sys/bus/iio/devices/iio:deviceX/in_accel_mount_matrix
+KernelVersion: 4.6
+Contact: linux-iio@vger.kernel.org
+Description:
+ Mounting matrix for IIO sensors. This is a rotation matrix which
+ informs userspace about sensor chip's placement relative to the
+ main hardware it is mounted on.
+ Main hardware placement is defined according to the local
+ reference frame related to the physical quantity the sensor
+ measures.
+ Given that the rotation matrix is defined in a board specific
+ way (platform data and / or device-tree), the main hardware
+ reference frame definition is left to the implementor's choice
+ (see below for a magnetometer example).
+ Applications should apply this rotation matrix to samples so
+ that when main hardware reference frame is aligned onto local
+ reference frame, then sensor chip reference frame is also
+ perfectly aligned with it.
+ Matrix is a 3x3 unitary matrix and typically looks like
+ [0, 1, 0; 1, 0, 0; 0, 0, -1]. Identity matrix
+ [1, 0, 0; 0, 1, 0; 0, 0, 1] means sensor chip and main hardware
+ are perfectly aligned with each other.
+
+ For example, a mounting matrix for a magnetometer sensor informs
+ userspace about sensor chip's ORIENTATION relative to the main
+ hardware.
+ More specifically, main hardware orientation is defined with
+ respect to the LOCAL EARTH GEOMAGNETIC REFERENCE FRAME where :
+ * Y is in the ground plane and positive towards magnetic North ;
+ * X is in the ground plane, perpendicular to the North axis and
+ positive towards the East ;
+ * Z is perpendicular to the ground plane and positive upwards.
+
+ An implementor might consider that for a hand-held device, a
+ 'natural' orientation would be 'front facing camera at the top'.
+ The main hardware reference frame could then be described as :
+ * Y is in the plane of the screen and is positive towards the
+ top of the screen ;
+ * X is in the plane of the screen, perpendicular to Y axis, and
+ positive towards the right hand side of the screen ;
+ * Z is perpendicular to the screen plane and positive out of the
+ screen.
+ Another example for a quadrotor UAV might be :
+ * Y is in the plane of the propellers and positive towards the
+ front-view camera;
+ * X is in the plane of the propellers, perpendicular to Y axis,
+ and positive towards the starboard side of the UAV ;
+ * Z is perpendicular to propellers plane and positive upwards.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_electricalconductivity_raw
+KernelVersion: 4.8
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled no offset etc.) electric conductivity reading that
+ can be processed to siemens per meter.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_raw
+KernelVersion: 4.10
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw counter device counts from channel Y. For quadrature
+ counters, multiplication by an available [Y]_scale results in
+ the counts of a single quadrature signal phase from channel Y.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_indexY_raw
+KernelVersion: 4.10
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw counter device index value from channel Y. This attribute
+ provides an absolute positional reference (e.g. a pulse once per
+ revolution) which may be used to home positional systems as
+ required.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_count_count_direction_available
+KernelVersion: 4.12
+Contact: linux-iio@vger.kernel.org
+Description:
+ A list of possible counting directions which are:
+ - "up" : counter device is increasing.
+ - "down": counter device is decreasing.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_countY_count_direction
+KernelVersion: 4.12
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw counter device counters direction for channel Y.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_phaseY_raw
+KernelVersion: 4.18
+Contact: linux-iio@vger.kernel.org
+Description:
+ Raw (unscaled) phase difference reading from channel Y
+ that can be processed to radians.
\ No newline at end of file