Update Linux to v5.10.109
Sourced from [1]
[1] https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.10.109.tar.xz
Change-Id: I19bca9fc6762d4e63bcf3e4cba88bbe560d9c76c
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index d4ac251..7315052 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -385,7 +385,7 @@
* OUTPUT device. This is ignored by video capture devices.
*
* @g_input_status: get input status. Same as the status field in the
- * &struct &v4l2_input
+ * &struct v4l2_input
*
* @s_stream: used to notify the driver that a video stream will start or has
* stopped.
@@ -406,12 +406,6 @@
*
* @query_dv_timings: callback for VIDIOC_QUERY_DV_TIMINGS() ioctl handler code.
*
- * @g_mbus_config: get supported mediabus configurations
- *
- * @s_mbus_config: set a certain mediabus configuration. This operation is added
- * for compatibility with soc-camera drivers and should not be used by new
- * software.
- *
* @s_rx_buffer: set a host allocated memory buffer for the subdev. The subdev
* can adjust @size to a lower value and must not write more data to the
* buffer starting at @data than the original value of @size.
@@ -439,10 +433,6 @@
struct v4l2_dv_timings *timings);
int (*query_dv_timings)(struct v4l2_subdev *sd,
struct v4l2_dv_timings *timings);
- int (*g_mbus_config)(struct v4l2_subdev *sd,
- struct v4l2_mbus_config *cfg);
- int (*s_mbus_config)(struct v4l2_subdev *sd,
- const struct v4l2_mbus_config *cfg);
int (*s_rx_buffer)(struct v4l2_subdev *sd, void *buf,
unsigned int *size);
};
@@ -570,9 +560,9 @@
*
* @rx_read: Reads received codes or pulse width data.
* The semantics are similar to a non-blocking read() call.
- * @rx_g_parameters: Get the current operating parameters and state of the
+ * @rx_g_parameters: Get the current operating parameters and state of
* the IR receiver.
- * @rx_s_parameters: Set the current operating parameters and state of the
+ * @rx_s_parameters: Set the current operating parameters and state of
* the IR receiver. It is recommended to call
* [rt]x_g_parameters first to fill out the current state, and only change
* the fields that need to be changed. Upon return, the actual device
@@ -586,9 +576,9 @@
*
* @tx_write: Writes codes or pulse width data for transmission.
* The semantics are similar to a non-blocking write() call.
- * @tx_g_parameters: Get the current operating parameters and state of the
+ * @tx_g_parameters: Get the current operating parameters and state of
* the IR transmitter.
- * @tx_s_parameters: Set the current operating parameters and state of the
+ * @tx_s_parameters: Set the current operating parameters and state of
* the IR transmitter. It is recommended to call
* [rt]x_g_parameters first to fill out the current state, and only change
* the fields that need to be changed. Upon return, the actual device
@@ -674,6 +664,30 @@
*
* @set_frame_desc: set the low level media bus frame parameters, @fd array
* may be adjusted by the subdev driver to device capabilities.
+ *
+ * @get_mbus_config: get the media bus configuration of a remote sub-device.
+ * The media bus configuration is usually retrieved from the
+ * firmware interface at sub-device probe time, immediately
+ * applied to the hardware and eventually adjusted by the
+ * driver. Remote sub-devices (usually video receivers) shall
+ * use this operation to query the transmitting end bus
+ * configuration in order to adjust their own one accordingly.
+ * Callers should make sure they get the most up-to-date as
+ * possible configuration from the remote end, likely calling
+ * this operation as close as possible to stream on time. The
+ * operation shall fail if the pad index it has been called on
+ * is not valid or in case of unrecoverable failures.
+ *
+ * @set_mbus_config: set the media bus configuration of a remote sub-device.
+ * This operations is intended to allow, in combination with
+ * the get_mbus_config operation, the negotiation of media bus
+ * configuration parameters between media sub-devices. The
+ * operation shall not fail if the requested configuration is
+ * not supported, but the driver shall update the content of
+ * the %config argument to reflect what has been actually
+ * applied to the hardware. The operation shall fail if the
+ * pad index it has been called on is not valid or in case of
+ * unrecoverable failures.
*/
struct v4l2_subdev_pad_ops {
int (*init_cfg)(struct v4l2_subdev *sd,
@@ -714,6 +728,10 @@
struct v4l2_mbus_frame_desc *fd);
int (*set_frame_desc)(struct v4l2_subdev *sd, unsigned int pad,
struct v4l2_mbus_frame_desc *fd);
+ int (*get_mbus_config)(struct v4l2_subdev *sd, unsigned int pad,
+ struct v4l2_mbus_config *config);
+ int (*set_mbus_config)(struct v4l2_subdev *sd, unsigned int pad,
+ struct v4l2_mbus_config *config);
};
/**
@@ -934,10 +952,10 @@
* @cfg: pointer to &struct v4l2_subdev_pad_config array.
* @pad: index of the pad in the @cfg array.
*/
-static inline struct v4l2_mbus_framefmt
-*v4l2_subdev_get_try_format(struct v4l2_subdev *sd,
- struct v4l2_subdev_pad_config *cfg,
- unsigned int pad)
+static inline struct v4l2_mbus_framefmt *
+v4l2_subdev_get_try_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ unsigned int pad)
{
if (WARN_ON(pad >= sd->entity.num_pads))
pad = 0;
@@ -952,10 +970,10 @@
* @cfg: pointer to &struct v4l2_subdev_pad_config array.
* @pad: index of the pad in the @cfg array.
*/
-static inline struct v4l2_rect
-*v4l2_subdev_get_try_crop(struct v4l2_subdev *sd,
- struct v4l2_subdev_pad_config *cfg,
- unsigned int pad)
+static inline struct v4l2_rect *
+v4l2_subdev_get_try_crop(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ unsigned int pad)
{
if (WARN_ON(pad >= sd->entity.num_pads))
pad = 0;
@@ -963,22 +981,23 @@
}
/**
- * v4l2_subdev_get_try_crop - ancillary routine to call
+ * v4l2_subdev_get_try_compose - ancillary routine to call
* &struct v4l2_subdev_pad_config->try_compose
*
* @sd: pointer to &struct v4l2_subdev
* @cfg: pointer to &struct v4l2_subdev_pad_config array.
* @pad: index of the pad in the @cfg array.
*/
-static inline struct v4l2_rect
-*v4l2_subdev_get_try_compose(struct v4l2_subdev *sd,
- struct v4l2_subdev_pad_config *cfg,
- unsigned int pad)
+static inline struct v4l2_rect *
+v4l2_subdev_get_try_compose(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ unsigned int pad)
{
if (WARN_ON(pad >= sd->entity.num_pads))
pad = 0;
return &cfg[pad].try_compose;
}
+
#endif
extern const struct v4l2_file_operations v4l2_subdev_fops;
@@ -1032,6 +1051,23 @@
#ifdef CONFIG_MEDIA_CONTROLLER
/**
+ * v4l2_subdev_get_fwnode_pad_1_to_1 - Get pad number from a subdev fwnode
+ * endpoint, assuming 1:1 port:pad
+ *
+ * @entity: Pointer to the subdev entity
+ * @endpoint: Pointer to a parsed fwnode endpoint
+ *
+ * This function can be used as the .get_fwnode_pad operation for
+ * subdevices that map port numbers and pad indexes 1:1. If the endpoint
+ * is owned by the subdevice, the function returns the endpoint port
+ * number.
+ *
+ * Returns the endpoint port number on success or a negative error code.
+ */
+int v4l2_subdev_get_fwnode_pad_1_to_1(struct media_entity *entity,
+ struct fwnode_endpoint *endpoint);
+
+/**
* v4l2_subdev_link_validate_default - validates a media link
*
* @sd: pointer to &struct v4l2_subdev
@@ -1094,10 +1130,10 @@
* @sd: pointer to the &struct v4l2_subdev
* @o: name of the element at &struct v4l2_subdev_ops that contains @f.
* Each element there groups a set of callbacks functions.
- * @f: callback function that will be called if @cond matches.
+ * @f: callback function to be called.
* The callback functions are defined in groups, according to
* each element at &struct v4l2_subdev_ops.
- * @args...: arguments for @f.
+ * @args: arguments for @f.
*
* Example: err = v4l2_subdev_call(sd, video, s_std, norm);
*/