Update Linux to v5.10.109
Sourced from [1]
[1] https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.10.109.tar.xz
Change-Id: I19bca9fc6762d4e63bcf3e4cba88bbe560d9c76c
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
diff --git a/include/linux/gpio/regmap.h b/include/linux/gpio/regmap.h
new file mode 100644
index 0000000..ad76f3d
--- /dev/null
+++ b/include/linux/gpio/regmap.h
@@ -0,0 +1,86 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef _LINUX_GPIO_REGMAP_H
+#define _LINUX_GPIO_REGMAP_H
+
+struct device;
+struct gpio_regmap;
+struct irq_domain;
+struct regmap;
+
+#define GPIO_REGMAP_ADDR_ZERO ((unsigned int)(-1))
+#define GPIO_REGMAP_ADDR(addr) ((addr) ? : GPIO_REGMAP_ADDR_ZERO)
+
+/**
+ * struct gpio_regmap_config - Description of a generic regmap gpio_chip.
+ * @parent: The parent device
+ * @regmap: The regmap used to access the registers
+ * given, the name of the device is used
+ * @label: (Optional) Descriptive name for GPIO controller.
+ * If not given, the name of the device is used.
+ * @ngpio: Number of GPIOs
+ * @names: (Optional) Array of names for gpios
+ * @reg_dat_base: (Optional) (in) register base address
+ * @reg_set_base: (Optional) set register base address
+ * @reg_clr_base: (Optional) clear register base address
+ * @reg_dir_in_base: (Optional) in setting register base address
+ * @reg_dir_out_base: (Optional) out setting register base address
+ * @reg_stride: (Optional) May be set if the registers (of the
+ * same type, dat, set, etc) are not consecutive.
+ * @ngpio_per_reg: Number of GPIOs per register
+ * @irq_domain: (Optional) IRQ domain if the controller is
+ * interrupt-capable
+ * @reg_mask_xlate: (Optional) Translates base address and GPIO
+ * offset to a register/bitmask pair. If not
+ * given the default gpio_regmap_simple_xlate()
+ * is used.
+ *
+ * The ->reg_mask_xlate translates a given base address and GPIO offset to
+ * register and mask pair. The base address is one of the given register
+ * base addresses in this structure.
+ *
+ * Although all register base addresses are marked as optional, there are
+ * several rules:
+ * 1. if you only have @reg_dat_base set, then it is input-only
+ * 2. if you only have @reg_set_base set, then it is output-only
+ * 3. if you have either @reg_dir_in_base or @reg_dir_out_base set, then
+ * you have to set both @reg_dat_base and @reg_set_base
+ * 4. if you have @reg_set_base set, you may also set @reg_clr_base to have
+ * two different registers for setting and clearing the output. This is
+ * also valid for the output-only case.
+ * 5. @reg_dir_in_base and @reg_dir_out_base are exclusive; is there really
+ * hardware which has redundant registers?
+ *
+ * Note: All base addresses may have the special value %GPIO_REGMAP_ADDR_ZERO
+ * which forces the address to the value 0.
+ */
+struct gpio_regmap_config {
+ struct device *parent;
+ struct regmap *regmap;
+
+ const char *label;
+ int ngpio;
+ const char *const *names;
+
+ unsigned int reg_dat_base;
+ unsigned int reg_set_base;
+ unsigned int reg_clr_base;
+ unsigned int reg_dir_in_base;
+ unsigned int reg_dir_out_base;
+ int reg_stride;
+ int ngpio_per_reg;
+ struct irq_domain *irq_domain;
+
+ int (*reg_mask_xlate)(struct gpio_regmap *gpio, unsigned int base,
+ unsigned int offset, unsigned int *reg,
+ unsigned int *mask);
+};
+
+struct gpio_regmap *gpio_regmap_register(const struct gpio_regmap_config *config);
+void gpio_regmap_unregister(struct gpio_regmap *gpio);
+struct gpio_regmap *devm_gpio_regmap_register(struct device *dev,
+ const struct gpio_regmap_config *config);
+void gpio_regmap_set_drvdata(struct gpio_regmap *gpio, void *data);
+void *gpio_regmap_get_drvdata(struct gpio_regmap *gpio);
+
+#endif /* _LINUX_GPIO_REGMAP_H */