Update Linux to v5.10.109
Sourced from [1]
[1] https://cdn.kernel.org/pub/linux/kernel/v5.x/linux-5.10.109.tar.xz
Change-Id: I19bca9fc6762d4e63bcf3e4cba88bbe560d9c76c
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h
index 681cb59..9281365 100644
--- a/include/drm/drm_connector.h
+++ b/include/drm/drm_connector.h
@@ -188,19 +188,19 @@
/**
* @y420_vdb_modes: bitmap of modes which can support ycbcr420
- * output only (not normal RGB/YCBCR444/422 outputs). There are total
- * 107 VICs defined by CEA-861-F spec, so the size is 128 bits to map
- * upto 128 VICs;
+ * output only (not normal RGB/YCBCR444/422 outputs). The max VIC
+ * defined by the CEA-861-G spec is 219, so the size is 256 bits to map
+ * up to 256 VICs.
*/
- unsigned long y420_vdb_modes[BITS_TO_LONGS(128)];
+ unsigned long y420_vdb_modes[BITS_TO_LONGS(256)];
/**
* @y420_cmdb_modes: bitmap of modes which can support ycbcr420
- * output also, along with normal HDMI outputs. There are total 107
- * VICs defined by CEA-861-F spec, so the size is 128 bits to map upto
- * 128 VICs;
+ * output also, along with normal HDMI outputs. The max VIC defined by
+ * the CEA-861-G spec is 219, so the size is 256 bits to map up to 256
+ * VICs.
*/
- unsigned long y420_cmdb_modes[BITS_TO_LONGS(128)];
+ unsigned long y420_cmdb_modes[BITS_TO_LONGS(256)];
/** @y420_cmdb_map: bitmap of SVD index, to extraxt vcb modes */
u64 y420_cmdb_map;
@@ -254,6 +254,23 @@
DRM_MODE_PANEL_ORIENTATION_RIGHT_UP,
};
+/**
+ * struct drm_monitor_range_info - Panel's Monitor range in EDID for
+ * &drm_display_info
+ *
+ * This struct is used to store a frequency range supported by panel
+ * as parsed from EDID's detailed monitor range descriptor block.
+ *
+ * @min_vfreq: This is the min supported refresh rate in Hz from
+ * EDID's detailed monitor range.
+ * @max_vfreq: This is the max supported refresh rate in Hz from
+ * EDID's detailed monitor range
+ */
+struct drm_monitor_range_info {
+ u8 min_vfreq;
+ u8 max_vfreq;
+};
+
/*
* This is a consolidated colorimetry list supported by HDMI and
* DP protocol standard. The respective connectors will register
@@ -281,6 +298,10 @@
/* Additional Colorimetry extension added as part of CTA 861.G */
#define DRM_MODE_COLORIMETRY_DCI_P3_RGB_D65 11
#define DRM_MODE_COLORIMETRY_DCI_P3_RGB_THEATER 12
+/* Additional Colorimetry Options added for DP 1.4a VSC Colorimetry Format */
+#define DRM_MODE_COLORIMETRY_RGB_WIDE_FIXED 13
+#define DRM_MODE_COLORIMETRY_RGB_WIDE_FLOAT 14
+#define DRM_MODE_COLORIMETRY_BT601_YCC 15
/**
* enum drm_bus_flags - bus_flags info for &drm_display_info
@@ -299,51 +320,97 @@
* opposite edge of the driving edge. Transmitters and receivers may however
* need to take other signal timings into account to convert between driving
* and sample edges.
- *
- * @DRM_BUS_FLAG_DE_LOW: The Data Enable signal is active low
- * @DRM_BUS_FLAG_DE_HIGH: The Data Enable signal is active high
- * @DRM_BUS_FLAG_PIXDATA_POSEDGE: Legacy value, do not use
- * @DRM_BUS_FLAG_PIXDATA_NEGEDGE: Legacy value, do not use
- * @DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE: Data is driven on the rising edge of
- * the pixel clock
- * @DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE: Data is driven on the falling edge of
- * the pixel clock
- * @DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE: Data is sampled on the rising edge of
- * the pixel clock
- * @DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE: Data is sampled on the falling edge of
- * the pixel clock
- * @DRM_BUS_FLAG_DATA_MSB_TO_LSB: Data is transmitted MSB to LSB on the bus
- * @DRM_BUS_FLAG_DATA_LSB_TO_MSB: Data is transmitted LSB to MSB on the bus
- * @DRM_BUS_FLAG_SYNC_POSEDGE: Legacy value, do not use
- * @DRM_BUS_FLAG_SYNC_NEGEDGE: Legacy value, do not use
- * @DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE: Sync signals are driven on the rising
- * edge of the pixel clock
- * @DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE: Sync signals are driven on the falling
- * edge of the pixel clock
- * @DRM_BUS_FLAG_SYNC_SAMPLE_POSEDGE: Sync signals are sampled on the rising
- * edge of the pixel clock
- * @DRM_BUS_FLAG_SYNC_SAMPLE_NEGEDGE: Sync signals are sampled on the falling
- * edge of the pixel clock
- * @DRM_BUS_FLAG_SHARP_SIGNALS: Set if the Sharp-specific signals
- * (SPL, CLS, PS, REV) must be used
*/
enum drm_bus_flags {
+ /**
+ * @DRM_BUS_FLAG_DE_LOW:
+ *
+ * The Data Enable signal is active low
+ */
DRM_BUS_FLAG_DE_LOW = BIT(0),
+
+ /**
+ * @DRM_BUS_FLAG_DE_HIGH:
+ *
+ * The Data Enable signal is active high
+ */
DRM_BUS_FLAG_DE_HIGH = BIT(1),
- DRM_BUS_FLAG_PIXDATA_POSEDGE = BIT(2),
- DRM_BUS_FLAG_PIXDATA_NEGEDGE = BIT(3),
- DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE = DRM_BUS_FLAG_PIXDATA_POSEDGE,
- DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE = DRM_BUS_FLAG_PIXDATA_NEGEDGE,
- DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE = DRM_BUS_FLAG_PIXDATA_NEGEDGE,
- DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE = DRM_BUS_FLAG_PIXDATA_POSEDGE,
+
+ /**
+ * @DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE:
+ *
+ * Data is driven on the rising edge of the pixel clock
+ */
+ DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE = BIT(2),
+
+ /**
+ * @DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE:
+ *
+ * Data is driven on the falling edge of the pixel clock
+ */
+ DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE = BIT(3),
+
+ /**
+ * @DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE:
+ *
+ * Data is sampled on the rising edge of the pixel clock
+ */
+ DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE = DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+
+ /**
+ * @DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE:
+ *
+ * Data is sampled on the falling edge of the pixel clock
+ */
+ DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE = DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE,
+
+ /**
+ * @DRM_BUS_FLAG_DATA_MSB_TO_LSB:
+ *
+ * Data is transmitted MSB to LSB on the bus
+ */
DRM_BUS_FLAG_DATA_MSB_TO_LSB = BIT(4),
+
+ /**
+ * @DRM_BUS_FLAG_DATA_LSB_TO_MSB:
+ *
+ * Data is transmitted LSB to MSB on the bus
+ */
DRM_BUS_FLAG_DATA_LSB_TO_MSB = BIT(5),
- DRM_BUS_FLAG_SYNC_POSEDGE = BIT(6),
- DRM_BUS_FLAG_SYNC_NEGEDGE = BIT(7),
- DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE = DRM_BUS_FLAG_SYNC_POSEDGE,
- DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE = DRM_BUS_FLAG_SYNC_NEGEDGE,
- DRM_BUS_FLAG_SYNC_SAMPLE_POSEDGE = DRM_BUS_FLAG_SYNC_NEGEDGE,
- DRM_BUS_FLAG_SYNC_SAMPLE_NEGEDGE = DRM_BUS_FLAG_SYNC_POSEDGE,
+
+ /**
+ * @DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE:
+ *
+ * Sync signals are driven on the rising edge of the pixel clock
+ */
+ DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE = BIT(6),
+
+ /**
+ * @DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE:
+ *
+ * Sync signals are driven on the falling edge of the pixel clock
+ */
+ DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE = BIT(7),
+
+ /**
+ * @DRM_BUS_FLAG_SYNC_SAMPLE_POSEDGE:
+ *
+ * Sync signals are sampled on the rising edge of the pixel clock
+ */
+ DRM_BUS_FLAG_SYNC_SAMPLE_POSEDGE = DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE,
+
+ /**
+ * @DRM_BUS_FLAG_SYNC_SAMPLE_NEGEDGE:
+ *
+ * Sync signals are sampled on the falling edge of the pixel clock
+ */
+ DRM_BUS_FLAG_SYNC_SAMPLE_NEGEDGE = DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE,
+
+ /**
+ * @DRM_BUS_FLAG_SHARP_SIGNALS:
+ *
+ * Set if the Sharp-specific signals (SPL, CLS, PS, REV) must be used
+ */
DRM_BUS_FLAG_SHARP_SIGNALS = BIT(8),
};
@@ -431,6 +498,14 @@
bool dvi_dual;
/**
+ * @is_hdmi: True if the sink is an HDMI device.
+ *
+ * This field shall be used instead of calling
+ * drm_detect_hdmi_monitor() when possible.
+ */
+ bool is_hdmi;
+
+ /**
* @has_hdmi_infoframe: Does the sink support the HDMI infoframe?
*/
bool has_hdmi_infoframe;
@@ -461,6 +536,11 @@
* @non_desktop: Non desktop display (HMD).
*/
bool non_desktop;
+
+ /**
+ * @monitor_range: Frequency range supported by monitor range descriptor
+ */
+ struct drm_monitor_range_info monitor_range;
};
int drm_display_info_set_bus_formats(struct drm_display_info *info,
@@ -1066,6 +1146,14 @@
unsigned int rotation_reflection;
/**
+ * @panel_orientation:
+ *
+ * drm-connector "panel orientation" property override value,
+ * DRM_MODE_PANEL_ORIENTATION_UNKNOWN if not set.
+ */
+ enum drm_panel_orientation panel_orientation;
+
+ /**
* @tv_margins: TV margins to apply to the mode.
*/
struct drm_connector_tv_margins tv_margins;
@@ -1287,13 +1375,15 @@
enum drm_connector_force force;
/** @override_edid: has the EDID been overwritten through debugfs for testing? */
bool override_edid;
+ /** @epoch_counter: used to detect any other changes in connector, besides status */
+ u64 epoch_counter;
-#define DRM_CONNECTOR_MAX_ENCODER 3
/**
- * @encoder_ids: Valid encoders for this connector. Please only use
- * drm_connector_for_each_possible_encoder() to enumerate these.
+ * @possible_encoders: Bit mask of encoders that can drive this
+ * connector, drm_encoder_index() determines the index into the bitfield
+ * and the bits are set with drm_connector_attach_encoder().
*/
- uint32_t encoder_ids[DRM_CONNECTOR_MAX_ENCODER];
+ u32 possible_encoders;
/**
* @encoder: Currently bound encoder driving this connector, if any.
@@ -1345,6 +1435,12 @@
* rev1.1 4.2.2.6
*/
bool edid_corrupt;
+ /**
+ * @real_edid_checksum: real edid checksum for corrupted edid block.
+ * Required in Displayport 1.4 compliance testing
+ * rev1.1 4.2.2.6
+ */
+ u8 real_edid_checksum;
/** @debugfs_entry: debugfs directory for this connector */
struct dentry *debugfs_entry;
@@ -1500,6 +1596,7 @@
DRM_CONNECTOR_UNREGISTERED;
}
+const char *drm_get_connector_type_name(unsigned int connector_type);
const char *drm_get_connector_status_name(enum drm_connector_status status);
const char *drm_get_subpixel_order_name(enum subpixel_order order);
const char *drm_get_dpms_name(int val);
@@ -1507,10 +1604,13 @@
const char *drm_get_dvi_i_select_name(int val);
const char *drm_get_tv_subconnector_name(int val);
const char *drm_get_tv_select_name(int val);
+const char *drm_get_dp_subconnector_name(int val);
const char *drm_get_content_protection_name(int val);
const char *drm_get_hdcp_content_type_name(int val);
int drm_mode_create_dvi_i_properties(struct drm_device *dev);
+void drm_connector_attach_dp_subconnector_property(struct drm_connector *connector);
+
int drm_mode_create_tv_margin_properties(struct drm_device *dev);
int drm_mode_create_tv_properties(struct drm_device *dev,
unsigned int num_modes,
@@ -1523,7 +1623,8 @@
int drm_connector_attach_vrr_capable_property(
struct drm_connector *connector);
int drm_mode_create_aspect_ratio_property(struct drm_device *dev);
-int drm_mode_create_colorspace_property(struct drm_connector *connector);
+int drm_mode_create_hdmi_colorspace_property(struct drm_connector *connector);
+int drm_mode_create_dp_colorspace_property(struct drm_connector *connector);
int drm_mode_create_content_type_property(struct drm_device *dev);
void drm_hdmi_avi_infoframe_content_type(struct hdmi_avi_infoframe *frame,
const struct drm_connector_state *conn_state);
@@ -1539,8 +1640,13 @@
uint64_t link_status);
void drm_connector_set_vrr_capable_property(
struct drm_connector *connector, bool capable);
-int drm_connector_init_panel_orientation_property(
- struct drm_connector *connector, int width, int height);
+int drm_connector_set_panel_orientation(
+ struct drm_connector *connector,
+ enum drm_panel_orientation panel_orientation);
+int drm_connector_set_panel_orientation_with_quirk(
+ struct drm_connector *connector,
+ enum drm_panel_orientation panel_orientation,
+ int width, int height);
int drm_connector_attach_max_bpc_property(struct drm_connector *connector,
int min, int max);
@@ -1562,9 +1668,9 @@
};
struct drm_tile_group *drm_mode_create_tile_group(struct drm_device *dev,
- char topology[8]);
+ const char topology[8]);
struct drm_tile_group *drm_mode_get_tile_group(struct drm_device *dev,
- char topology[8]);
+ const char topology[8]);
void drm_mode_put_tile_group(struct drm_device *dev,
struct drm_tile_group *tg);
@@ -1608,13 +1714,9 @@
* drm_connector_for_each_possible_encoder - iterate connector's possible encoders
* @connector: &struct drm_connector pointer
* @encoder: &struct drm_encoder pointer used as cursor
- * @__i: int iteration cursor, for macro-internal use
*/
-#define drm_connector_for_each_possible_encoder(connector, encoder, __i) \
- for ((__i) = 0; (__i) < ARRAY_SIZE((connector)->encoder_ids) && \
- (connector)->encoder_ids[(__i)] != 0; (__i)++) \
- for_each_if((encoder) = \
- drm_encoder_find((connector)->dev, NULL, \
- (connector)->encoder_ids[(__i)])) \
+#define drm_connector_for_each_possible_encoder(connector, encoder) \
+ drm_for_each_encoder_mask(encoder, (connector)->dev, \
+ (connector)->possible_encoders)
#endif