Update Linux to v5.4.2
Change-Id: Idf6911045d9d382da2cfe01b1edff026404ac8fd
diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h
index 87823ac..6087be2 100644
--- a/drivers/usb/mtu3/mtu3.h
+++ b/drivers/usb/mtu3/mtu3.h
@@ -63,6 +63,15 @@
#define MTU3_U2_IP_SLOT_DEFAULT 1
/**
+ * IP TRUNK version
+ * from 0x1003 version, USB3 Gen2 is supported, two changes affect driver:
+ * 1. MAXPKT and MULTI bits layout of TXCSR1 and RXCSR1 are adjusted,
+ * but not backward compatible
+ * 2. QMU extend buffer length supported
+ */
+#define MTU3_TRUNK_VERS_1003 0x1003
+
+/**
* Normally the device works on HS or SS, to simplify fifo management,
* devide fifo into some 512B parts, use bitmap to manage it; And
* 128 bits size of bitmap is large enough, that means it can manage
@@ -135,45 +144,33 @@
* The format of TX GPD is a little different from RX one.
* And the size of GPD is 16 bytes.
*
- * @flag:
+ * @dw0_info:
* bit0: Hardware Own (HWO)
* bit1: Buffer Descriptor Present (BDP), always 0, BD is not supported
* bit2: Bypass (BPS), 1: HW skips this GPD if HWO = 1
+ * bit6: [EL] Zero Length Packet (ZLP), moved from @dw3_info[29]
* bit7: Interrupt On Completion (IOC)
- * @chksum: This is used to validate the contents of this GPD;
- * If TXQ_CS_EN / RXQ_CS_EN bit is set, an interrupt is issued
- * when checksum validation fails;
- * Checksum value is calculated over the 16 bytes of the GPD by default;
- * @data_buf_len (RX ONLY): This value indicates the length of
- * the assigned data buffer
- * @tx_ext_addr (TX ONLY): [3:0] are 4 extension bits of @buffer,
- * [7:4] are 4 extension bits of @next_gpd
+ * bit[31:16]: ([EL] bit[31:12]) allow data buffer length (RX ONLY),
+ * the buffer length of the data to receive
+ * bit[23:16]: ([EL] bit[31:24]) extension address (TX ONLY),
+ * lower 4 bits are extension bits of @buffer,
+ * upper 4 bits are extension bits of @next_gpd
* @next_gpd: Physical address of the next GPD
* @buffer: Physical address of the data buffer
- * @buf_len:
- * (TX): This value indicates the length of the assigned data buffer
- * (RX): The total length of data received
- * @ext_len: reserved
- * @rx_ext_addr(RX ONLY): [3:0] are 4 extension bits of @buffer,
- * [7:4] are 4 extension bits of @next_gpd
- * @ext_flag:
- * bit5 (TX ONLY): Zero Length Packet (ZLP),
+ * @dw3_info:
+ * bit[15:0]: ([EL] bit[19:0]) data buffer length,
+ * (TX): the buffer length of the data to transmit
+ * (RX): The total length of data received
+ * bit[23:16]: ([EL] bit[31:24]) extension address (RX ONLY),
+ * lower 4 bits are extension bits of @buffer,
+ * upper 4 bits are extension bits of @next_gpd
+ * bit29: ([EL] abandoned) Zero Length Packet (ZLP) (TX ONLY)
*/
struct qmu_gpd {
- __u8 flag;
- __u8 chksum;
- union {
- __le16 data_buf_len;
- __le16 tx_ext_addr;
- };
+ __le32 dw0_info;
__le32 next_gpd;
__le32 buffer;
- __le16 buf_len;
- union {
- __u8 ext_len;
- __u8 rx_ext_addr;
- };
- __u8 ext_flag;
+ __le32 dw3_info;
} __packed;
/**
@@ -202,6 +199,9 @@
* @id_nb : notifier for iddig(idpin) detection
* @id_work : work of iddig detection notifier
* @id_event : event of iddig detecion notifier
+* @role_sw : use USB Role Switch to support dual-role switch, can't use
+* extcon at the same time, and extcon is deprecated.
+* @role_sw_used : true when the USB Role Switch is used.
* @is_u3_drd: whether port0 supports usb3.0 dual-role device or not
* @manual_drd_enabled: it's true when supports dual-role device by debugfs
* to switch host/device modes depending on user input.
@@ -215,6 +215,8 @@
struct notifier_block id_nb;
struct work_struct id_work;
unsigned long id_event;
+ struct usb_role_switch *role_sw;
+ bool role_sw_used;
bool is_u3_drd;
bool manual_drd_enabled;
};
@@ -316,6 +318,7 @@
* @may_wakeup: means device's remote wakeup is enabled
* @is_self_powered: is reported in device status and the config descriptor
* @delayed_status: true when function drivers ask for delayed status
+ * @gen2cp: compatible with USB3 Gen2 IP
* @ep0_req: dummy request used while handling standard USB requests
* for GET_STATUS and SET_SEL
* @setup_buf: ep0 response buffer for GET_STATUS and SET_SEL requests
@@ -356,6 +359,7 @@
unsigned u2_enable:1;
unsigned is_u3_ip:1;
unsigned delayed_status:1;
+ unsigned gen2cp:1;
u8 address;
u8 test_mode_nr;