Update Linux to v5.4.2
Change-Id: Idf6911045d9d382da2cfe01b1edff026404ac8fd
diff --git a/drivers/net/ethernet/realtek/atp.c b/drivers/net/ethernet/realtek/atp.c
index 7e011c1..58e0ca9 100644
--- a/drivers/net/ethernet/realtek/atp.c
+++ b/drivers/net/ethernet/realtek/atp.c
@@ -454,14 +454,14 @@
{
struct net_local *lp = netdev_priv(dev);
long ioaddr = dev->base_addr;
- int i;
+ int i;
/* Turn off the printer multiplexer on the 8012. */
for (i = 0; i < 8; i++)
outb(mux_8012[i], ioaddr + PAR_DATA);
write_reg_high(ioaddr, CMR1, CMR1h_RESET);
- for (i = 0; i < 6; i++)
+ for (i = 0; i < 6; i++)
write_reg_byte(ioaddr, PAR0 + i, dev->dev_addr[i]);
write_reg_high(ioaddr, CMR2, lp->addr_mode);
@@ -471,18 +471,18 @@
(read_nibble(ioaddr, CMR2_h) >> 3) & 0x0f);
}
- write_reg(ioaddr, CMR2, CMR2_IRQOUT);
- write_reg_high(ioaddr, CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE);
+ write_reg(ioaddr, CMR2, CMR2_IRQOUT);
+ write_reg_high(ioaddr, CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE);
/* Enable the interrupt line from the serial port. */
outb(Ctrl_SelData + Ctrl_IRQEN, ioaddr + PAR_CONTROL);
/* Unmask the interesting interrupts. */
- write_reg(ioaddr, IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK);
- write_reg_high(ioaddr, IMR, ISRh_RxErr);
+ write_reg(ioaddr, IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK);
+ write_reg_high(ioaddr, IMR, ISRh_RxErr);
lp->tx_unit_busy = 0;
- lp->pac_cnt_in_tx_buf = 0;
+ lp->pac_cnt_in_tx_buf = 0;
lp->saved_tx_size = 0;
}
@@ -610,10 +610,12 @@
write_reg(ioaddr, CMR2, CMR2_NULL);
write_reg(ioaddr, IMR, 0);
- if (net_debug > 5) printk(KERN_DEBUG "%s: In interrupt ", dev->name);
- while (--boguscount > 0) {
+ if (net_debug > 5)
+ printk(KERN_DEBUG "%s: In interrupt ", dev->name);
+ while (--boguscount > 0) {
int status = read_nibble(ioaddr, ISR);
- if (net_debug > 5) printk("loop status %02x..", status);
+ if (net_debug > 5)
+ printk("loop status %02x..", status);
if (status & (ISR_RxOK<<3)) {
handled = 1;
@@ -640,7 +642,8 @@
} while (--boguscount > 0);
} else if (status & ((ISR_TxErr + ISR_TxOK)<<3)) {
handled = 1;
- if (net_debug > 6) printk("handling Tx done..");
+ if (net_debug > 6)
+ printk("handling Tx done..");
/* Clear the Tx interrupt. We should check for too many failures
and reinitialize the adapter. */
write_reg(ioaddr, ISR, ISR_TxErr + ISR_TxOK);
@@ -680,7 +683,7 @@
break;
} else
break;
- }
+ }
/* This following code fixes a rare (and very difficult to track down)
problem where the adapter forgets its ethernet address. */
@@ -694,7 +697,7 @@
}
/* Tell the adapter that it can go back to using the output line as IRQ. */
- write_reg(ioaddr, CMR2, CMR2_IRQOUT);
+ write_reg(ioaddr, CMR2, CMR2_IRQOUT);
/* Enable the physical interrupt line, which is sure to be low until.. */
outb(Ctrl_SelData + Ctrl_IRQEN, ioaddr + PAR_CONTROL);
/* .. we enable the interrupt sources. */