Update Linux to v5.4.2
Change-Id: Idf6911045d9d382da2cfe01b1edff026404ac8fd
diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
index de15bf5..aac507b 100644
--- a/drivers/extcon/Kconfig
+++ b/drivers/extcon/Kconfig
@@ -1,3 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
menuconfig EXTCON
tristate "External Connector Class (extcon) support"
help
@@ -30,12 +31,24 @@
config EXTCON_AXP288
tristate "X-Power AXP288 EXTCON support"
- depends on MFD_AXP20X && USB_SUPPORT && X86
+ depends on MFD_AXP20X && USB_SUPPORT && X86 && ACPI
select USB_ROLE_SWITCH
help
Say Y here to enable support for USB peripheral detection
and USB MUX switching by X-Power AXP288 PMIC.
+config EXTCON_FSA9480
+ tristate "FSA9480 EXTCON Support"
+ depends on INPUT && I2C
+ select IRQ_DOMAIN
+ select REGMAP_I2C
+ help
+ If you say yes here you get support for the Fairchild Semiconductor
+ FSA9480 microUSB switch and accessory detector chip. The FSA9480 is a USB
+ port accessory detector and switch. The FSA9480 is fully controlled using
+ I2C and enables USB data, stereo and mono audio, video, microphone
+ and UART data to use a common connector port.
+
config EXTCON_GPIO
tristate "GPIO extcon support"
depends on GPIOLIB || COMPILE_TEST
@@ -60,6 +73,13 @@
Say Y here to enable extcon support for charger detection / control
on the Intel Cherrytrail Whiskey Cove PMIC.
+config EXTCON_INTEL_MRFLD
+ tristate "Intel Merrifield Basin Cove PMIC extcon driver"
+ depends on INTEL_SOC_PMIC_MRFLD
+ help
+ Say Y here to enable extcon support for charger detection / control
+ on the Intel Merrifield Basin Cove PMIC.
+
config EXTCON_MAX14577
tristate "Maxim MAX14577/77836 EXTCON Support"
depends on MFD_MAX14577
@@ -114,6 +134,14 @@
Say Y here to enable support for USB peripheral and USB host
detection by palmas usb.
+config EXTCON_PTN5150
+ tristate "NXP PTN5150 CC LOGIC USB EXTCON support"
+ depends on I2C && (GPIOLIB || COMPILE_TEST)
+ select REGMAP_I2C
+ help
+ Say Y here to enable support for USB peripheral and USB host
+ detection by NXP PTN5150 CC (Configuration Channel) logic chip.
+
config EXTCON_QCOM_SPMI_MISC
tristate "Qualcomm USB extcon support"
depends on ARCH_QCOM || COMPILE_TEST
@@ -153,7 +181,7 @@
config EXTCON_USBC_CROS_EC
tristate "ChromeOS Embedded Controller EXTCON support"
- depends on MFD_CROS_EC
+ depends on CROS_EC
help
Say Y here to enable USB Type C cable detection extcon support when
using Chrome OS EC based USB Type-C ports.
diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
index 0888fde..52096fd 100644
--- a/drivers/extcon/Makefile
+++ b/drivers/extcon/Makefile
@@ -8,15 +8,18 @@
obj-$(CONFIG_EXTCON_ADC_JACK) += extcon-adc-jack.o
obj-$(CONFIG_EXTCON_ARIZONA) += extcon-arizona.o
obj-$(CONFIG_EXTCON_AXP288) += extcon-axp288.o
+obj-$(CONFIG_EXTCON_FSA9480) += extcon-fsa9480.o
obj-$(CONFIG_EXTCON_GPIO) += extcon-gpio.o
obj-$(CONFIG_EXTCON_INTEL_INT3496) += extcon-intel-int3496.o
obj-$(CONFIG_EXTCON_INTEL_CHT_WC) += extcon-intel-cht-wc.o
+obj-$(CONFIG_EXTCON_INTEL_MRFLD) += extcon-intel-mrfld.o
obj-$(CONFIG_EXTCON_MAX14577) += extcon-max14577.o
obj-$(CONFIG_EXTCON_MAX3355) += extcon-max3355.o
obj-$(CONFIG_EXTCON_MAX77693) += extcon-max77693.o
obj-$(CONFIG_EXTCON_MAX77843) += extcon-max77843.o
obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o
obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o
+obj-$(CONFIG_EXTCON_PTN5150) += extcon-ptn5150.o
obj-$(CONFIG_EXTCON_QCOM_SPMI_MISC) += extcon-qcom-spmi-misc.o
obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o
obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o
diff --git a/drivers/extcon/devres.c b/drivers/extcon/devres.c
index f599aed..f9d52e8 100644
--- a/drivers/extcon/devres.c
+++ b/drivers/extcon/devres.c
@@ -1,17 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
/*
* drivers/extcon/devres.c - EXTCON device's resource management
*
* Copyright (C) 2016 Samsung Electronics
* Author: Chanwoo Choi <cw00.choi@samsung.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include "extcon.h"
@@ -205,7 +197,7 @@
/**
* devm_extcon_unregister_notifier()
- - Resource-managed extcon_unregister_notifier()
+ * - Resource-managed extcon_unregister_notifier()
* @dev: the device owning the extcon device being created
* @edev: the extcon device
* @id: the unique id among the extcon enumeration
diff --git a/drivers/extcon/extcon-adc-jack.c b/drivers/extcon/extcon-adc-jack.c
index 1802635..ad02dc6 100644
--- a/drivers/extcon/extcon-adc-jack.c
+++ b/drivers/extcon/extcon-adc-jack.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
/*
* drivers/extcon/extcon-adc-jack.c
*
@@ -10,11 +11,6 @@
* MyungJoo Ham <myungjoo.ham@samsung.com>
*
* Modified for calling to IIO to get adc by <anish.singh@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
*/
#include <linux/module.h>
@@ -144,10 +140,8 @@
return err;
data->irq = platform_get_irq(pdev, 0);
- if (data->irq < 0) {
- dev_err(&pdev->dev, "platform_get_irq failed\n");
+ if (data->irq < 0)
return -ENODEV;
- }
err = request_any_context_irq(data->irq, adc_jack_irq_thread,
pdata->irq_flags, pdata->name, data);
diff --git a/drivers/extcon/extcon-arizona.c b/drivers/extcon/extcon-arizona.c
index da0e9bc..e970134 100644
--- a/drivers/extcon/extcon-arizona.c
+++ b/drivers/extcon/extcon-arizona.c
@@ -1,17 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
/*
* extcon-arizona.c - Extcon driver Wolfson Arizona devices
*
* Copyright (C) 2012-2014 Wolfson Microelectronics plc
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include <linux/kernel.h>
@@ -335,10 +326,12 @@
arizona_extcon_pulse_micbias(info);
- regmap_update_bits_check(arizona->regmap, ARIZONA_MIC_DETECT_1,
- ARIZONA_MICD_ENA, ARIZONA_MICD_ENA,
- &change);
- if (!change) {
+ ret = regmap_update_bits_check(arizona->regmap, ARIZONA_MIC_DETECT_1,
+ ARIZONA_MICD_ENA, ARIZONA_MICD_ENA,
+ &change);
+ if (ret < 0) {
+ dev_err(arizona->dev, "Failed to enable micd: %d\n", ret);
+ } else if (!change) {
regulator_disable(info->micvdd);
pm_runtime_put_autosuspend(info->dev);
}
@@ -350,12 +343,14 @@
const char *widget = arizona_extcon_get_micbias(info);
struct snd_soc_dapm_context *dapm = arizona->dapm;
struct snd_soc_component *component = snd_soc_dapm_to_component(dapm);
- bool change;
+ bool change = false;
int ret;
- regmap_update_bits_check(arizona->regmap, ARIZONA_MIC_DETECT_1,
- ARIZONA_MICD_ENA, 0,
- &change);
+ ret = regmap_update_bits_check(arizona->regmap, ARIZONA_MIC_DETECT_1,
+ ARIZONA_MICD_ENA, 0,
+ &change);
+ if (ret < 0)
+ dev_err(arizona->dev, "Failed to disable micd: %d\n", ret);
ret = snd_soc_component_disable_pin(component, widget);
if (ret != 0)
@@ -1258,7 +1253,7 @@
int i, j;
u32 *vals;
- nconfs = device_property_read_u32_array(arizona->dev, prop, NULL, 0);
+ nconfs = device_property_count_u32(arizona->dev, prop);
if (nconfs <= 0)
return 0;
@@ -1726,6 +1721,19 @@
struct arizona_extcon_info *info = platform_get_drvdata(pdev);
struct arizona *arizona = info->arizona;
int jack_irq_rise, jack_irq_fall;
+ bool change;
+ int ret;
+
+ ret = regmap_update_bits_check(arizona->regmap, ARIZONA_MIC_DETECT_1,
+ ARIZONA_MICD_ENA, 0,
+ &change);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to disable micd on remove: %d\n",
+ ret);
+ } else if (change) {
+ regulator_disable(info->micvdd);
+ pm_runtime_put(info->dev);
+ }
gpiod_put(info->micd_pol_gpio);
diff --git a/drivers/extcon/extcon-axp288.c b/drivers/extcon/extcon-axp288.c
index a983708..415afaf 100644
--- a/drivers/extcon/extcon-axp288.c
+++ b/drivers/extcon/extcon-axp288.c
@@ -1,18 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
/*
* extcon-axp288.c - X-Power AXP288 PMIC extcon cable detection driver
*
* Copyright (c) 2017-2018 Hans de Goede <hdegoede@redhat.com>
* Copyright (C) 2015 Intel Corporation
* Author: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include <linux/acpi.h>
@@ -129,7 +121,6 @@
"Last shutdown caused by PMIC UVLO threshold",
"Last shutdown caused by SOC initiated cold off",
"Last shutdown caused by user pressing the power button",
- NULL,
};
/*
@@ -138,18 +129,21 @@
*/
static void axp288_extcon_log_rsi(struct axp288_extcon_info *info)
{
- const char * const *rsi;
unsigned int val, i, clear_mask = 0;
+ unsigned long bits;
int ret;
ret = regmap_read(info->regmap, AXP288_PS_BOOT_REASON_REG, &val);
- for (i = 0, rsi = axp288_pwr_up_down_info; *rsi; rsi++, i++) {
- if (val & BIT(i)) {
- dev_dbg(info->dev, "%s\n", *rsi);
- clear_mask |= BIT(i);
- }
+ if (ret < 0) {
+ dev_err(info->dev, "failed to read reset source indicator\n");
+ return;
}
+ bits = val & GENMASK(ARRAY_SIZE(axp288_pwr_up_down_info) - 1, 0);
+ for_each_set_bit(i, &bits, ARRAY_SIZE(axp288_pwr_up_down_info))
+ dev_dbg(info->dev, "%s\n", axp288_pwr_up_down_info[i]);
+ clear_mask = bits;
+
/* Clear the register value for next reboot (write 1 to clear bit) */
regmap_write(info->regmap, AXP288_PS_BOOT_REASON_REG, clear_mask);
}
@@ -333,7 +327,7 @@
struct axp288_extcon_info *info;
struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
struct device *dev = &pdev->dev;
- const char *name;
+ struct acpi_device *adev;
int ret, i, pirq;
info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
@@ -357,9 +351,10 @@
if (ret)
return ret;
- name = acpi_dev_get_first_match_name("INT3496", NULL, -1);
- if (name) {
- info->id_extcon = extcon_get_extcon_dev(name);
+ adev = acpi_dev_get_first_match_dev("INT3496", NULL, -1);
+ if (adev) {
+ info->id_extcon = extcon_get_extcon_dev(acpi_dev_name(adev));
+ put_device(&adev->dev);
if (!info->id_extcon)
return -EPROBE_DEFER;
diff --git a/drivers/extcon/extcon-fsa9480.c b/drivers/extcon/extcon-fsa9480.c
new file mode 100644
index 0000000..8405512
--- /dev/null
+++ b/drivers/extcon/extcon-fsa9480.c
@@ -0,0 +1,396 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * extcon-fsa9480.c - Fairchild Semiconductor FSA9480 extcon driver
+ *
+ * Copyright (c) 2019 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Loosely based on old fsa9480 misc-device driver.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/bitops.h>
+#include <linux/interrupt.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/kobject.h>
+#include <linux/extcon-provider.h>
+#include <linux/irqdomain.h>
+#include <linux/regmap.h>
+
+/* FSA9480 I2C registers */
+#define FSA9480_REG_DEVID 0x01
+#define FSA9480_REG_CTRL 0x02
+#define FSA9480_REG_INT1 0x03
+#define FSA9480_REG_INT2 0x04
+#define FSA9480_REG_INT1_MASK 0x05
+#define FSA9480_REG_INT2_MASK 0x06
+#define FSA9480_REG_ADC 0x07
+#define FSA9480_REG_TIMING1 0x08
+#define FSA9480_REG_TIMING2 0x09
+#define FSA9480_REG_DEV_T1 0x0a
+#define FSA9480_REG_DEV_T2 0x0b
+#define FSA9480_REG_BTN1 0x0c
+#define FSA9480_REG_BTN2 0x0d
+#define FSA9480_REG_CK 0x0e
+#define FSA9480_REG_CK_INT1 0x0f
+#define FSA9480_REG_CK_INT2 0x10
+#define FSA9480_REG_CK_INTMASK1 0x11
+#define FSA9480_REG_CK_INTMASK2 0x12
+#define FSA9480_REG_MANSW1 0x13
+#define FSA9480_REG_MANSW2 0x14
+#define FSA9480_REG_END 0x15
+
+/* Control */
+#define CON_SWITCH_OPEN (1 << 4)
+#define CON_RAW_DATA (1 << 3)
+#define CON_MANUAL_SW (1 << 2)
+#define CON_WAIT (1 << 1)
+#define CON_INT_MASK (1 << 0)
+#define CON_MASK (CON_SWITCH_OPEN | CON_RAW_DATA | \
+ CON_MANUAL_SW | CON_WAIT)
+
+/* Device Type 1 */
+#define DEV_USB_OTG 7
+#define DEV_DEDICATED_CHG 6
+#define DEV_USB_CHG 5
+#define DEV_CAR_KIT 4
+#define DEV_UART 3
+#define DEV_USB 2
+#define DEV_AUDIO_2 1
+#define DEV_AUDIO_1 0
+
+#define DEV_T1_USB_MASK (DEV_USB_OTG | DEV_USB)
+#define DEV_T1_UART_MASK (DEV_UART)
+#define DEV_T1_CHARGER_MASK (DEV_DEDICATED_CHG | DEV_USB_CHG)
+
+/* Device Type 2 */
+#define DEV_AV 14
+#define DEV_TTY 13
+#define DEV_PPD 12
+#define DEV_JIG_UART_OFF 11
+#define DEV_JIG_UART_ON 10
+#define DEV_JIG_USB_OFF 9
+#define DEV_JIG_USB_ON 8
+
+#define DEV_T2_USB_MASK (DEV_JIG_USB_OFF | DEV_JIG_USB_ON)
+#define DEV_T2_UART_MASK (DEV_JIG_UART_OFF | DEV_JIG_UART_ON)
+#define DEV_T2_JIG_MASK (DEV_JIG_USB_OFF | DEV_JIG_USB_ON | \
+ DEV_JIG_UART_OFF | DEV_JIG_UART_ON)
+
+/*
+ * Manual Switch
+ * D- [7:5] / D+ [4:2]
+ * 000: Open all / 001: USB / 010: AUDIO / 011: UART / 100: V_AUDIO
+ */
+#define SW_VAUDIO ((4 << 5) | (4 << 2))
+#define SW_UART ((3 << 5) | (3 << 2))
+#define SW_AUDIO ((2 << 5) | (2 << 2))
+#define SW_DHOST ((1 << 5) | (1 << 2))
+#define SW_AUTO ((0 << 5) | (0 << 2))
+
+/* Interrupt 1 */
+#define INT1_MASK (0xff << 0)
+#define INT_DETACH (1 << 1)
+#define INT_ATTACH (1 << 0)
+
+/* Interrupt 2 mask */
+#define INT2_MASK (0x1f << 0)
+
+/* Timing Set 1 */
+#define TIMING1_ADC_500MS (0x6 << 0)
+
+struct fsa9480_usbsw {
+ struct device *dev;
+ struct regmap *regmap;
+ struct extcon_dev *edev;
+ u16 cable;
+};
+
+static const unsigned int fsa9480_extcon_cable[] = {
+ EXTCON_USB_HOST,
+ EXTCON_USB,
+ EXTCON_CHG_USB_DCP,
+ EXTCON_CHG_USB_SDP,
+ EXTCON_CHG_USB_ACA,
+ EXTCON_JACK_LINE_OUT,
+ EXTCON_JACK_VIDEO_OUT,
+ EXTCON_JIG,
+
+ EXTCON_NONE,
+};
+
+static const u64 cable_types[] = {
+ [DEV_USB_OTG] = BIT_ULL(EXTCON_USB_HOST),
+ [DEV_DEDICATED_CHG] = BIT_ULL(EXTCON_USB) | BIT_ULL(EXTCON_CHG_USB_DCP),
+ [DEV_USB_CHG] = BIT_ULL(EXTCON_USB) | BIT_ULL(EXTCON_CHG_USB_SDP),
+ [DEV_CAR_KIT] = BIT_ULL(EXTCON_USB) | BIT_ULL(EXTCON_CHG_USB_SDP)
+ | BIT_ULL(EXTCON_JACK_LINE_OUT),
+ [DEV_UART] = BIT_ULL(EXTCON_JIG),
+ [DEV_USB] = BIT_ULL(EXTCON_USB) | BIT_ULL(EXTCON_CHG_USB_SDP),
+ [DEV_AUDIO_2] = BIT_ULL(EXTCON_JACK_LINE_OUT),
+ [DEV_AUDIO_1] = BIT_ULL(EXTCON_JACK_LINE_OUT),
+ [DEV_AV] = BIT_ULL(EXTCON_JACK_LINE_OUT)
+ | BIT_ULL(EXTCON_JACK_VIDEO_OUT),
+ [DEV_TTY] = BIT_ULL(EXTCON_JIG),
+ [DEV_PPD] = BIT_ULL(EXTCON_JACK_LINE_OUT) | BIT_ULL(EXTCON_CHG_USB_ACA),
+ [DEV_JIG_UART_OFF] = BIT_ULL(EXTCON_JIG),
+ [DEV_JIG_UART_ON] = BIT_ULL(EXTCON_JIG),
+ [DEV_JIG_USB_OFF] = BIT_ULL(EXTCON_USB) | BIT_ULL(EXTCON_JIG),
+ [DEV_JIG_USB_ON] = BIT_ULL(EXTCON_USB) | BIT_ULL(EXTCON_JIG),
+};
+
+/* Define regmap configuration of FSA9480 for I2C communication */
+static bool fsa9480_volatile_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case FSA9480_REG_INT1_MASK:
+ return true;
+ default:
+ break;
+ }
+ return false;
+}
+
+static const struct regmap_config fsa9480_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .volatile_reg = fsa9480_volatile_reg,
+ .max_register = FSA9480_REG_END,
+};
+
+static int fsa9480_write_reg(struct fsa9480_usbsw *usbsw, int reg, int value)
+{
+ int ret;
+
+ ret = regmap_write(usbsw->regmap, reg, value);
+ if (ret < 0)
+ dev_err(usbsw->dev, "%s: err %d\n", __func__, ret);
+
+ return ret;
+}
+
+static int fsa9480_read_reg(struct fsa9480_usbsw *usbsw, int reg)
+{
+ int ret, val;
+
+ ret = regmap_read(usbsw->regmap, reg, &val);
+ if (ret < 0) {
+ dev_err(usbsw->dev, "%s: err %d\n", __func__, ret);
+ return ret;
+ }
+
+ return val;
+}
+
+static int fsa9480_read_irq(struct fsa9480_usbsw *usbsw, int *value)
+{
+ u8 regs[2];
+ int ret;
+
+ ret = regmap_bulk_read(usbsw->regmap, FSA9480_REG_INT1, regs, 2);
+ if (ret < 0)
+ dev_err(usbsw->dev, "%s: err %d\n", __func__, ret);
+
+ *value = regs[1] << 8 | regs[0];
+ return ret;
+}
+
+static void fsa9480_handle_change(struct fsa9480_usbsw *usbsw,
+ u16 mask, bool attached)
+{
+ while (mask) {
+ int dev = fls64(mask) - 1;
+ u64 cables = cable_types[dev];
+
+ while (cables) {
+ int cable = fls64(cables) - 1;
+
+ extcon_set_state_sync(usbsw->edev, cable, attached);
+ cables &= ~BIT_ULL(cable);
+ }
+
+ mask &= ~BIT_ULL(dev);
+ }
+}
+
+static void fsa9480_detect_dev(struct fsa9480_usbsw *usbsw)
+{
+ int val1, val2;
+ u16 val;
+
+ val1 = fsa9480_read_reg(usbsw, FSA9480_REG_DEV_T1);
+ val2 = fsa9480_read_reg(usbsw, FSA9480_REG_DEV_T2);
+ if (val1 < 0 || val2 < 0) {
+ dev_err(usbsw->dev, "%s: failed to read registers", __func__);
+ return;
+ }
+ val = val2 << 8 | val1;
+
+ dev_info(usbsw->dev, "dev1: 0x%x, dev2: 0x%x\n", val1, val2);
+
+ /* handle detached cables first */
+ fsa9480_handle_change(usbsw, usbsw->cable & ~val, false);
+
+ /* then handle attached ones */
+ fsa9480_handle_change(usbsw, val & ~usbsw->cable, true);
+
+ usbsw->cable = val;
+}
+
+static irqreturn_t fsa9480_irq_handler(int irq, void *data)
+{
+ struct fsa9480_usbsw *usbsw = data;
+ int intr = 0;
+
+ /* clear interrupt */
+ fsa9480_read_irq(usbsw, &intr);
+ if (!intr)
+ return IRQ_NONE;
+
+ /* device detection */
+ fsa9480_detect_dev(usbsw);
+
+ return IRQ_HANDLED;
+}
+
+static int fsa9480_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct fsa9480_usbsw *info;
+ int ret;
+
+ if (!client->irq) {
+ dev_err(&client->dev, "no interrupt provided\n");
+ return -EINVAL;
+ }
+
+ info = devm_kzalloc(&client->dev, sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+ info->dev = &client->dev;
+
+ i2c_set_clientdata(client, info);
+
+ /* External connector */
+ info->edev = devm_extcon_dev_allocate(info->dev,
+ fsa9480_extcon_cable);
+ if (IS_ERR(info->edev)) {
+ dev_err(info->dev, "failed to allocate memory for extcon\n");
+ ret = -ENOMEM;
+ return ret;
+ }
+
+ ret = devm_extcon_dev_register(info->dev, info->edev);
+ if (ret) {
+ dev_err(info->dev, "failed to register extcon device\n");
+ return ret;
+ }
+
+ info->regmap = devm_regmap_init_i2c(client, &fsa9480_regmap_config);
+ if (IS_ERR(info->regmap)) {
+ ret = PTR_ERR(info->regmap);
+ dev_err(info->dev, "failed to allocate register map: %d\n",
+ ret);
+ return ret;
+ }
+
+ /* ADC Detect Time: 500ms */
+ fsa9480_write_reg(info, FSA9480_REG_TIMING1, TIMING1_ADC_500MS);
+
+ /* configure automatic switching */
+ fsa9480_write_reg(info, FSA9480_REG_CTRL, CON_MASK);
+
+ /* unmask interrupt (attach/detach only) */
+ fsa9480_write_reg(info, FSA9480_REG_INT1_MASK,
+ INT1_MASK & ~(INT_ATTACH | INT_DETACH));
+ fsa9480_write_reg(info, FSA9480_REG_INT2_MASK, INT2_MASK);
+
+ ret = devm_request_threaded_irq(info->dev, client->irq, NULL,
+ fsa9480_irq_handler,
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ "fsa9480", info);
+ if (ret) {
+ dev_err(info->dev, "failed to request IRQ\n");
+ return ret;
+ }
+
+ device_init_wakeup(info->dev, true);
+ fsa9480_detect_dev(info);
+
+ return 0;
+}
+
+static int fsa9480_remove(struct i2c_client *client)
+{
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int fsa9480_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+
+ if (device_may_wakeup(&client->dev) && client->irq)
+ enable_irq_wake(client->irq);
+
+ return 0;
+}
+
+static int fsa9480_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+
+ if (device_may_wakeup(&client->dev) && client->irq)
+ disable_irq_wake(client->irq);
+
+ return 0;
+}
+#endif
+
+static const struct dev_pm_ops fsa9480_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(fsa9480_suspend, fsa9480_resume)
+};
+
+static const struct i2c_device_id fsa9480_id[] = {
+ { "fsa9480", 0 },
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, fsa9480_id);
+
+static const struct of_device_id fsa9480_of_match[] = {
+ { .compatible = "fcs,fsa9480", },
+ { .compatible = "fcs,fsa880", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, fsa9480_of_match);
+
+static struct i2c_driver fsa9480_i2c_driver = {
+ .driver = {
+ .name = "fsa9480",
+ .pm = &fsa9480_pm_ops,
+ .of_match_table = fsa9480_of_match,
+ },
+ .probe = fsa9480_probe,
+ .remove = fsa9480_remove,
+ .id_table = fsa9480_id,
+};
+
+static int __init fsa9480_module_init(void)
+{
+ return i2c_add_driver(&fsa9480_i2c_driver);
+}
+subsys_initcall(fsa9480_module_init);
+
+static void __exit fsa9480_module_exit(void)
+{
+ i2c_del_driver(&fsa9480_i2c_driver);
+}
+module_exit(fsa9480_module_exit);
+
+MODULE_DESCRIPTION("Fairchild Semiconductor FSA9480 extcon driver");
+MODULE_AUTHOR("Tomasz Figa <tomasz.figa@gmail.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/extcon/extcon-gpio.c b/drivers/extcon/extcon-gpio.c
index 13ba3a6..c211222 100644
--- a/drivers/extcon/extcon-gpio.c
+++ b/drivers/extcon/extcon-gpio.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
/*
* extcon_gpio.c - Single-state GPIO extcon driver based on extcon class
*
@@ -6,15 +7,6 @@
*
* Modified by MyungJoo Ham <myungjoo.ham@samsung.com> to support extcon
* (originally switch class is supported)
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include <linux/extcon-provider.h>
@@ -30,26 +22,22 @@
/**
* struct gpio_extcon_data - A simple GPIO-controlled extcon device state container.
* @edev: Extcon device.
- * @irq: Interrupt line for the external connector.
* @work: Work fired by the interrupt.
* @debounce_jiffies: Number of jiffies to wait for the GPIO to stabilize, from the debounce
* value.
* @gpiod: GPIO descriptor for this external connector.
* @extcon_id: The unique id of specific external connector.
* @debounce: Debounce time for GPIO IRQ in ms.
- * @irq_flags: IRQ Flags (e.g., IRQF_TRIGGER_LOW).
* @check_on_resume: Boolean describing whether to check the state of gpio
* while resuming from sleep.
*/
struct gpio_extcon_data {
struct extcon_dev *edev;
- int irq;
struct delayed_work work;
unsigned long debounce_jiffies;
struct gpio_desc *gpiod;
unsigned int extcon_id;
unsigned long debounce;
- unsigned long irq_flags;
bool check_on_resume;
};
@@ -77,6 +65,8 @@
{
struct gpio_extcon_data *data;
struct device *dev = &pdev->dev;
+ unsigned long irq_flags;
+ int irq;
int ret;
data = devm_kzalloc(dev, sizeof(struct gpio_extcon_data), GFP_KERNEL);
@@ -90,15 +80,26 @@
* developed to get the extcon id from device-tree or others.
* On later, it have to be solved.
*/
- if (!data->irq_flags || data->extcon_id > EXTCON_NONE)
+ if (data->extcon_id > EXTCON_NONE)
return -EINVAL;
data->gpiod = devm_gpiod_get(dev, "extcon", GPIOD_IN);
if (IS_ERR(data->gpiod))
return PTR_ERR(data->gpiod);
- data->irq = gpiod_to_irq(data->gpiod);
- if (data->irq <= 0)
- return data->irq;
+ irq = gpiod_to_irq(data->gpiod);
+ if (irq <= 0)
+ return irq;
+
+ /*
+ * It is unlikely that this is an acknowledged interrupt that goes
+ * away after handling, what we are looking for are falling edges
+ * if the signal is active low, and rising edges if the signal is
+ * active high.
+ */
+ if (gpiod_is_active_low(data->gpiod))
+ irq_flags = IRQF_TRIGGER_FALLING;
+ else
+ irq_flags = IRQF_TRIGGER_RISING;
/* Allocate the memory of extcon devie and register extcon device */
data->edev = devm_extcon_dev_allocate(dev, &data->extcon_id);
@@ -117,8 +118,8 @@
* Request the interrupt of gpio to detect whether external connector
* is attached or detached.
*/
- ret = devm_request_any_context_irq(dev, data->irq,
- gpio_irq_handler, data->irq_flags,
+ ret = devm_request_any_context_irq(dev, irq,
+ gpio_irq_handler, irq_flags,
pdev->name, data);
if (ret < 0)
return ret;
diff --git a/drivers/extcon/extcon-intel-cht-wc.c b/drivers/extcon/extcon-intel-cht-wc.c
index 5e1dd27..9d32150 100644
--- a/drivers/extcon/extcon-intel-cht-wc.c
+++ b/drivers/extcon/extcon-intel-cht-wc.c
@@ -1,18 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0
/*
* Extcon charger detection driver for Intel Cherrytrail Whiskey Cove PMIC
* Copyright (C) 2017 Hans de Goede <hdegoede@redhat.com>
*
* Based on various non upstream patches to support the CHT Whiskey Cove PMIC:
* Copyright (C) 2013-2015 Intel Corporation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
*/
#include <linux/extcon-provider.h>
@@ -25,6 +17,8 @@
#include <linux/regmap.h>
#include <linux/slab.h>
+#include "extcon-intel.h"
+
#define CHT_WC_PHYCTRL 0x5e07
#define CHT_WC_CHGRCTRL0 0x5e16
@@ -32,12 +26,20 @@
#define CHT_WC_CHGRCTRL0_EMRGCHREN BIT(1)
#define CHT_WC_CHGRCTRL0_EXTCHRDIS BIT(2)
#define CHT_WC_CHGRCTRL0_SWCONTROL BIT(3)
-#define CHT_WC_CHGRCTRL0_TTLCK_MASK BIT(4)
-#define CHT_WC_CHGRCTRL0_CCSM_OFF_MASK BIT(5)
-#define CHT_WC_CHGRCTRL0_DBPOFF_MASK BIT(6)
-#define CHT_WC_CHGRCTRL0_WDT_NOKICK BIT(7)
+#define CHT_WC_CHGRCTRL0_TTLCK BIT(4)
+#define CHT_WC_CHGRCTRL0_CCSM_OFF BIT(5)
+#define CHT_WC_CHGRCTRL0_DBPOFF BIT(6)
+#define CHT_WC_CHGRCTRL0_CHR_WDT_NOKICK BIT(7)
-#define CHT_WC_CHGRCTRL1 0x5e17
+#define CHT_WC_CHGRCTRL1 0x5e17
+#define CHT_WC_CHGRCTRL1_FUSB_INLMT_100 BIT(0)
+#define CHT_WC_CHGRCTRL1_FUSB_INLMT_150 BIT(1)
+#define CHT_WC_CHGRCTRL1_FUSB_INLMT_500 BIT(2)
+#define CHT_WC_CHGRCTRL1_FUSB_INLMT_900 BIT(3)
+#define CHT_WC_CHGRCTRL1_FUSB_INLMT_1500 BIT(4)
+#define CHT_WC_CHGRCTRL1_FTEMP_EVENT BIT(5)
+#define CHT_WC_CHGRCTRL1_OTGMODE BIT(6)
+#define CHT_WC_CHGRCTRL1_DBPEN BIT(7)
#define CHT_WC_USBSRC 0x5e29
#define CHT_WC_USBSRC_STS_MASK GENMASK(1, 0)
@@ -52,33 +54,34 @@
#define CHT_WC_USBSRC_TYPE_ACA 4
#define CHT_WC_USBSRC_TYPE_SE1 5
#define CHT_WC_USBSRC_TYPE_MHL 6
-#define CHT_WC_USBSRC_TYPE_FLOAT_DP_DN 7
+#define CHT_WC_USBSRC_TYPE_FLOATING 7
#define CHT_WC_USBSRC_TYPE_OTHER 8
#define CHT_WC_USBSRC_TYPE_DCP_EXTPHY 9
+#define CHT_WC_CHGDISCTRL 0x5e2f
+#define CHT_WC_CHGDISCTRL_OUT BIT(0)
+/* 0 - open drain, 1 - regular push-pull output */
+#define CHT_WC_CHGDISCTRL_DRV BIT(4)
+/* 0 - pin is controlled by SW, 1 - by HW */
+#define CHT_WC_CHGDISCTRL_FN BIT(6)
+
#define CHT_WC_PWRSRC_IRQ 0x6e03
#define CHT_WC_PWRSRC_IRQ_MASK 0x6e0f
#define CHT_WC_PWRSRC_STS 0x6e1e
#define CHT_WC_PWRSRC_VBUS BIT(0)
#define CHT_WC_PWRSRC_DC BIT(1)
-#define CHT_WC_PWRSRC_BAT BIT(2)
-#define CHT_WC_PWRSRC_ID_GND BIT(3)
-#define CHT_WC_PWRSRC_ID_FLOAT BIT(4)
+#define CHT_WC_PWRSRC_BATT BIT(2)
+#define CHT_WC_PWRSRC_USBID_MASK GENMASK(4, 3)
+#define CHT_WC_PWRSRC_USBID_SHIFT 3
+#define CHT_WC_PWRSRC_RID_ACA 0
+#define CHT_WC_PWRSRC_RID_GND 1
+#define CHT_WC_PWRSRC_RID_FLOAT 2
#define CHT_WC_VBUS_GPIO_CTLO 0x6e2d
#define CHT_WC_VBUS_GPIO_CTLO_OUTPUT BIT(0)
#define CHT_WC_VBUS_GPIO_CTLO_DRV_OD BIT(4)
#define CHT_WC_VBUS_GPIO_CTLO_DIR_OUT BIT(5)
-enum cht_wc_usb_id {
- USB_ID_OTG,
- USB_ID_GND,
- USB_ID_FLOAT,
- USB_RID_A,
- USB_RID_B,
- USB_RID_C,
-};
-
enum cht_wc_mux_select {
MUX_SEL_PMIC = 0,
MUX_SEL_SOC,
@@ -104,16 +107,20 @@
static int cht_wc_extcon_get_id(struct cht_wc_extcon_data *ext, int pwrsrc_sts)
{
- if (pwrsrc_sts & CHT_WC_PWRSRC_ID_GND)
- return USB_ID_GND;
- if (pwrsrc_sts & CHT_WC_PWRSRC_ID_FLOAT)
- return USB_ID_FLOAT;
-
- /*
- * Once we have iio support for the gpadc we should read the USBID
- * gpadc channel here and determine ACA role based on that.
- */
- return USB_ID_FLOAT;
+ switch ((pwrsrc_sts & CHT_WC_PWRSRC_USBID_MASK) >> CHT_WC_PWRSRC_USBID_SHIFT) {
+ case CHT_WC_PWRSRC_RID_GND:
+ return INTEL_USB_ID_GND;
+ case CHT_WC_PWRSRC_RID_FLOAT:
+ return INTEL_USB_ID_FLOAT;
+ case CHT_WC_PWRSRC_RID_ACA:
+ default:
+ /*
+ * Once we have IIO support for the GPADC we should read
+ * the USBID GPADC channel here and determine ACA role
+ * based on that.
+ */
+ return INTEL_USB_ID_FLOAT;
+ }
}
static int cht_wc_extcon_get_charger(struct cht_wc_extcon_data *ext,
@@ -156,9 +163,9 @@
dev_warn(ext->dev,
"Unhandled charger type %d, defaulting to SDP\n",
ret);
- /* Fall through, treat as SDP */
+ return EXTCON_CHG_USB_SDP;
case CHT_WC_USBSRC_TYPE_SDP:
- case CHT_WC_USBSRC_TYPE_FLOAT_DP_DN:
+ case CHT_WC_USBSRC_TYPE_FLOATING:
case CHT_WC_USBSRC_TYPE_OTHER:
return EXTCON_CHG_USB_SDP;
case CHT_WC_USBSRC_TYPE_CDP:
@@ -199,6 +206,30 @@
dev_err(ext->dev, "Error writing Vbus GPIO CTLO: %d\n", ret);
}
+static void cht_wc_extcon_set_otgmode(struct cht_wc_extcon_data *ext,
+ bool enable)
+{
+ unsigned int val = enable ? CHT_WC_CHGRCTRL1_OTGMODE : 0;
+ int ret;
+
+ ret = regmap_update_bits(ext->regmap, CHT_WC_CHGRCTRL1,
+ CHT_WC_CHGRCTRL1_OTGMODE, val);
+ if (ret)
+ dev_err(ext->dev, "Error updating CHGRCTRL1 reg: %d\n", ret);
+}
+
+static void cht_wc_extcon_enable_charging(struct cht_wc_extcon_data *ext,
+ bool enable)
+{
+ unsigned int val = enable ? 0 : CHT_WC_CHGDISCTRL_OUT;
+ int ret;
+
+ ret = regmap_update_bits(ext->regmap, CHT_WC_CHGDISCTRL,
+ CHT_WC_CHGDISCTRL_OUT, val);
+ if (ret)
+ dev_err(ext->dev, "Error updating CHGDISCTRL reg: %d\n", ret);
+}
+
/* Small helper to sync EXTCON_CHG_USB_SDP and EXTCON_USB state */
static void cht_wc_extcon_set_state(struct cht_wc_extcon_data *ext,
unsigned int cable, bool state)
@@ -222,11 +253,17 @@
}
id = cht_wc_extcon_get_id(ext, pwrsrc_sts);
- if (id == USB_ID_GND) {
+ if (id == INTEL_USB_ID_GND) {
+ cht_wc_extcon_enable_charging(ext, false);
+ cht_wc_extcon_set_otgmode(ext, true);
+
/* The 5v boost causes a false VBUS / SDP detect, skip */
goto charger_det_done;
}
+ cht_wc_extcon_set_otgmode(ext, false);
+ cht_wc_extcon_enable_charging(ext, true);
+
/* Plugged into a host/charger or not connected? */
if (!(pwrsrc_sts & CHT_WC_PWRSRC_VBUS)) {
/* Route D+ and D- to PMIC for future charger detection */
@@ -249,7 +286,7 @@
ext->previous_cable = cable;
}
- ext->usb_host = ((id == USB_ID_GND) || (id == USB_RID_A));
+ ext->usb_host = ((id == INTEL_USB_ID_GND) || (id == INTEL_USB_RID_A));
extcon_set_state_sync(ext->edev, EXTCON_USB_HOST, ext->usb_host);
}
@@ -279,7 +316,15 @@
{
int ret, mask, val;
- mask = CHT_WC_CHGRCTRL0_SWCONTROL | CHT_WC_CHGRCTRL0_CCSM_OFF_MASK;
+ val = enable ? 0 : CHT_WC_CHGDISCTRL_FN;
+ ret = regmap_update_bits(ext->regmap, CHT_WC_CHGDISCTRL,
+ CHT_WC_CHGDISCTRL_FN, val);
+ if (ret)
+ dev_err(ext->dev,
+ "Error setting sw control for CHGDIS pin: %d\n",
+ ret);
+
+ mask = CHT_WC_CHGRCTRL0_SWCONTROL | CHT_WC_CHGRCTRL0_CCSM_OFF;
val = enable ? mask : 0;
ret = regmap_update_bits(ext->regmap, CHT_WC_CHGRCTRL0, mask, val);
if (ret)
@@ -292,6 +337,7 @@
{
struct intel_soc_pmic *pmic = dev_get_drvdata(pdev->dev.parent);
struct cht_wc_extcon_data *ext;
+ unsigned long mask = ~(CHT_WC_PWRSRC_VBUS | CHT_WC_PWRSRC_USBID_MASK);
int irq, ret;
irq = platform_get_irq(pdev, 0);
@@ -329,7 +375,10 @@
/* Enable sw control */
ret = cht_wc_extcon_sw_control(ext, true);
if (ret)
- return ret;
+ goto disable_sw_control;
+
+ /* Disable charging by external battery charger */
+ cht_wc_extcon_enable_charging(ext, false);
/* Register extcon device */
ret = devm_extcon_dev_register(ext->dev, ext->edev);
@@ -352,9 +401,7 @@
}
/* Unmask irqs */
- ret = regmap_write(ext->regmap, CHT_WC_PWRSRC_IRQ_MASK,
- (int)~(CHT_WC_PWRSRC_VBUS | CHT_WC_PWRSRC_ID_GND |
- CHT_WC_PWRSRC_ID_FLOAT));
+ ret = regmap_write(ext->regmap, CHT_WC_PWRSRC_IRQ_MASK, mask);
if (ret) {
dev_err(ext->dev, "Error writing irq-mask: %d\n", ret);
goto disable_sw_control;
diff --git a/drivers/extcon/extcon-intel-int3496.c b/drivers/extcon/extcon-intel-int3496.c
index fd24deb..80c9abc 100644
--- a/drivers/extcon/extcon-intel-int3496.c
+++ b/drivers/extcon/extcon-intel-int3496.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
/*
* Intel INT3496 ACPI device extcon driver
*
@@ -7,15 +8,6 @@
*
* Copyright (c) 2014, Intel Corporation.
* Author: David Cohen <david.a.cohen@linux.intel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include <linux/acpi.h>
@@ -192,4 +184,4 @@
MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
MODULE_DESCRIPTION("Intel INT3496 ACPI device extcon driver");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/extcon/extcon-intel-mrfld.c b/drivers/extcon/extcon-intel-mrfld.c
new file mode 100644
index 0000000..f47016f
--- /dev/null
+++ b/drivers/extcon/extcon-intel-mrfld.c
@@ -0,0 +1,284 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * extcon driver for Basin Cove PMIC
+ *
+ * Copyright (c) 2019, Intel Corporation.
+ * Author: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
+ */
+
+#include <linux/extcon-provider.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/intel_soc_pmic.h>
+#include <linux/mfd/intel_soc_pmic_mrfld.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "extcon-intel.h"
+
+#define BCOVE_USBIDCTRL 0x19
+#define BCOVE_USBIDCTRL_ID BIT(0)
+#define BCOVE_USBIDCTRL_ACA BIT(1)
+#define BCOVE_USBIDCTRL_ALL (BCOVE_USBIDCTRL_ID | BCOVE_USBIDCTRL_ACA)
+
+#define BCOVE_USBIDSTS 0x1a
+#define BCOVE_USBIDSTS_GND BIT(0)
+#define BCOVE_USBIDSTS_RARBRC_MASK GENMASK(2, 1)
+#define BCOVE_USBIDSTS_RARBRC_SHIFT 1
+#define BCOVE_USBIDSTS_NO_ACA 0
+#define BCOVE_USBIDSTS_R_ID_A 1
+#define BCOVE_USBIDSTS_R_ID_B 2
+#define BCOVE_USBIDSTS_R_ID_C 3
+#define BCOVE_USBIDSTS_FLOAT BIT(3)
+#define BCOVE_USBIDSTS_SHORT BIT(4)
+
+#define BCOVE_CHGRIRQ_ALL (BCOVE_CHGRIRQ_VBUSDET | BCOVE_CHGRIRQ_DCDET | \
+ BCOVE_CHGRIRQ_BATTDET | BCOVE_CHGRIRQ_USBIDDET)
+
+#define BCOVE_CHGRCTRL0 0x4b
+#define BCOVE_CHGRCTRL0_CHGRRESET BIT(0)
+#define BCOVE_CHGRCTRL0_EMRGCHREN BIT(1)
+#define BCOVE_CHGRCTRL0_EXTCHRDIS BIT(2)
+#define BCOVE_CHGRCTRL0_SWCONTROL BIT(3)
+#define BCOVE_CHGRCTRL0_TTLCK BIT(4)
+#define BCOVE_CHGRCTRL0_BIT_5 BIT(5)
+#define BCOVE_CHGRCTRL0_BIT_6 BIT(6)
+#define BCOVE_CHGRCTRL0_CHR_WDT_NOKICK BIT(7)
+
+struct mrfld_extcon_data {
+ struct device *dev;
+ struct regmap *regmap;
+ struct extcon_dev *edev;
+ unsigned int status;
+ unsigned int id;
+};
+
+static const unsigned int mrfld_extcon_cable[] = {
+ EXTCON_USB,
+ EXTCON_USB_HOST,
+ EXTCON_CHG_USB_SDP,
+ EXTCON_CHG_USB_CDP,
+ EXTCON_CHG_USB_DCP,
+ EXTCON_CHG_USB_ACA,
+ EXTCON_NONE,
+};
+
+static int mrfld_extcon_clear(struct mrfld_extcon_data *data, unsigned int reg,
+ unsigned int mask)
+{
+ return regmap_update_bits(data->regmap, reg, mask, 0x00);
+}
+
+static int mrfld_extcon_set(struct mrfld_extcon_data *data, unsigned int reg,
+ unsigned int mask)
+{
+ return regmap_update_bits(data->regmap, reg, mask, 0xff);
+}
+
+static int mrfld_extcon_sw_control(struct mrfld_extcon_data *data, bool enable)
+{
+ unsigned int mask = BCOVE_CHGRCTRL0_SWCONTROL;
+ struct device *dev = data->dev;
+ int ret;
+
+ if (enable)
+ ret = mrfld_extcon_set(data, BCOVE_CHGRCTRL0, mask);
+ else
+ ret = mrfld_extcon_clear(data, BCOVE_CHGRCTRL0, mask);
+ if (ret)
+ dev_err(dev, "can't set SW control: %d\n", ret);
+ return ret;
+}
+
+static int mrfld_extcon_get_id(struct mrfld_extcon_data *data)
+{
+ struct regmap *regmap = data->regmap;
+ unsigned int id;
+ bool ground;
+ int ret;
+
+ ret = regmap_read(regmap, BCOVE_USBIDSTS, &id);
+ if (ret)
+ return ret;
+
+ if (id & BCOVE_USBIDSTS_FLOAT)
+ return INTEL_USB_ID_FLOAT;
+
+ switch ((id & BCOVE_USBIDSTS_RARBRC_MASK) >> BCOVE_USBIDSTS_RARBRC_SHIFT) {
+ case BCOVE_USBIDSTS_R_ID_A:
+ return INTEL_USB_RID_A;
+ case BCOVE_USBIDSTS_R_ID_B:
+ return INTEL_USB_RID_B;
+ case BCOVE_USBIDSTS_R_ID_C:
+ return INTEL_USB_RID_C;
+ }
+
+ /*
+ * PMIC A0 reports USBIDSTS_GND = 1 for ID_GND,
+ * but PMIC B0 reports USBIDSTS_GND = 0 for ID_GND.
+ * Thus we must check this bit at last.
+ */
+ ground = id & BCOVE_USBIDSTS_GND;
+ switch ('A' + BCOVE_MAJOR(data->id)) {
+ case 'A':
+ return ground ? INTEL_USB_ID_GND : INTEL_USB_ID_FLOAT;
+ case 'B':
+ return ground ? INTEL_USB_ID_FLOAT : INTEL_USB_ID_GND;
+ }
+
+ /* Unknown or unsupported type */
+ return INTEL_USB_ID_FLOAT;
+}
+
+static int mrfld_extcon_role_detect(struct mrfld_extcon_data *data)
+{
+ unsigned int id;
+ bool usb_host;
+ int ret;
+
+ ret = mrfld_extcon_get_id(data);
+ if (ret < 0)
+ return ret;
+
+ id = ret;
+
+ usb_host = (id == INTEL_USB_ID_GND) || (id == INTEL_USB_RID_A);
+ extcon_set_state_sync(data->edev, EXTCON_USB_HOST, usb_host);
+
+ return 0;
+}
+
+static int mrfld_extcon_cable_detect(struct mrfld_extcon_data *data)
+{
+ struct regmap *regmap = data->regmap;
+ unsigned int status, change;
+ int ret;
+
+ /*
+ * It seems SCU firmware clears the content of BCOVE_CHGRIRQ1
+ * and makes it useless for OS. Instead we compare a previously
+ * stored status to the current one, provided by BCOVE_SCHGRIRQ1.
+ */
+ ret = regmap_read(regmap, BCOVE_SCHGRIRQ1, &status);
+ if (ret)
+ return ret;
+
+ change = status ^ data->status;
+ if (!change)
+ return -ENODATA;
+
+ if (change & BCOVE_CHGRIRQ_USBIDDET) {
+ ret = mrfld_extcon_role_detect(data);
+ if (ret)
+ return ret;
+ }
+
+ data->status = status;
+
+ return 0;
+}
+
+static irqreturn_t mrfld_extcon_interrupt(int irq, void *dev_id)
+{
+ struct mrfld_extcon_data *data = dev_id;
+ int ret;
+
+ ret = mrfld_extcon_cable_detect(data);
+
+ mrfld_extcon_clear(data, BCOVE_MIRQLVL1, BCOVE_LVL1_CHGR);
+
+ return ret ? IRQ_NONE: IRQ_HANDLED;
+}
+
+static int mrfld_extcon_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct intel_soc_pmic *pmic = dev_get_drvdata(dev->parent);
+ struct regmap *regmap = pmic->regmap;
+ struct mrfld_extcon_data *data;
+ unsigned int id;
+ int irq, ret;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->dev = dev;
+ data->regmap = regmap;
+
+ data->edev = devm_extcon_dev_allocate(dev, mrfld_extcon_cable);
+ if (IS_ERR(data->edev))
+ return -ENOMEM;
+
+ ret = devm_extcon_dev_register(dev, data->edev);
+ if (ret < 0) {
+ dev_err(dev, "can't register extcon device: %d\n", ret);
+ return ret;
+ }
+
+ ret = devm_request_threaded_irq(dev, irq, NULL, mrfld_extcon_interrupt,
+ IRQF_ONESHOT | IRQF_SHARED, pdev->name,
+ data);
+ if (ret) {
+ dev_err(dev, "can't register IRQ handler: %d\n", ret);
+ return ret;
+ }
+
+ ret = regmap_read(regmap, BCOVE_ID, &id);
+ if (ret) {
+ dev_err(dev, "can't read PMIC ID: %d\n", ret);
+ return ret;
+ }
+
+ data->id = id;
+
+ ret = mrfld_extcon_sw_control(data, true);
+ if (ret)
+ return ret;
+
+ /* Get initial state */
+ mrfld_extcon_role_detect(data);
+
+ mrfld_extcon_clear(data, BCOVE_MIRQLVL1, BCOVE_LVL1_CHGR);
+ mrfld_extcon_clear(data, BCOVE_MCHGRIRQ1, BCOVE_CHGRIRQ_ALL);
+
+ mrfld_extcon_set(data, BCOVE_USBIDCTRL, BCOVE_USBIDCTRL_ALL);
+
+ platform_set_drvdata(pdev, data);
+
+ return 0;
+}
+
+static int mrfld_extcon_remove(struct platform_device *pdev)
+{
+ struct mrfld_extcon_data *data = platform_get_drvdata(pdev);
+
+ mrfld_extcon_sw_control(data, false);
+
+ return 0;
+}
+
+static const struct platform_device_id mrfld_extcon_id_table[] = {
+ { .name = "mrfld_bcove_pwrsrc" },
+ {}
+};
+MODULE_DEVICE_TABLE(platform, mrfld_extcon_id_table);
+
+static struct platform_driver mrfld_extcon_driver = {
+ .driver = {
+ .name = "mrfld_bcove_pwrsrc",
+ },
+ .probe = mrfld_extcon_probe,
+ .remove = mrfld_extcon_remove,
+ .id_table = mrfld_extcon_id_table,
+};
+module_platform_driver(mrfld_extcon_driver);
+
+MODULE_AUTHOR("Andy Shevchenko <andriy.shevchenko@linux.intel.com>");
+MODULE_DESCRIPTION("extcon driver for Intel Merrifield Basin Cove PMIC");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/extcon/extcon-intel.h b/drivers/extcon/extcon-intel.h
new file mode 100644
index 0000000..0ad645e
--- /dev/null
+++ b/drivers/extcon/extcon-intel.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Header file for Intel extcon hardware
+ *
+ * Copyright (C) 2019 Intel Corporation. All rights reserved.
+ */
+
+#ifndef __EXTCON_INTEL_H__
+#define __EXTCON_INTEL_H__
+
+enum extcon_intel_usb_id {
+ INTEL_USB_ID_OTG,
+ INTEL_USB_ID_GND,
+ INTEL_USB_ID_FLOAT,
+ INTEL_USB_RID_A,
+ INTEL_USB_RID_B,
+ INTEL_USB_RID_C,
+};
+
+#endif /* __EXTCON_INTEL_H__ */
diff --git a/drivers/extcon/extcon-max14577.c b/drivers/extcon/extcon-max14577.c
index b871836..32f6634 100644
--- a/drivers/extcon/extcon-max14577.c
+++ b/drivers/extcon/extcon-max14577.c
@@ -1,20 +1,10 @@
-/*
- * extcon-max14577.c - MAX14577/77836 extcon driver to support MUIC
- *
- * Copyright (C) 2013,2014 Samsung Electronics
- * Chanwoo Choi <cw00.choi@samsung.com>
- * Krzysztof Kozlowski <krzk@kernel.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0+
+//
+// extcon-max14577.c - MAX14577/77836 extcon driver to support MUIC
+//
+// Copyright (C) 2013,2014 Samsung Electronics
+// Chanwoo Choi <cw00.choi@samsung.com>
+// Krzysztof Kozlowski <krzk@kernel.org>
#include <linux/kernel.h>
#include <linux/module.h>
@@ -667,6 +657,8 @@
struct max14577 *max14577 = dev_get_drvdata(pdev->dev.parent);
struct max14577_muic_info *info;
int delay_jiffies;
+ int cable_type;
+ bool attached;
int ret;
int i;
u8 id;
@@ -735,8 +727,17 @@
info->path_uart = CTRL1_SW_UART;
delay_jiffies = msecs_to_jiffies(DELAY_MS_DEFAULT);
- /* Set initial path for UART */
- max14577_muic_set_path(info, info->path_uart, true);
+ /* Set initial path for UART when JIG is connected to get serial logs */
+ ret = max14577_bulk_read(info->max14577->regmap,
+ MAX14577_MUIC_REG_STATUS1, info->status, 2);
+ if (ret) {
+ dev_err(info->dev, "Cannot read STATUS registers\n");
+ return ret;
+ }
+ cable_type = max14577_muic_get_cable_type(info, MAX14577_CABLE_GROUP_ADC,
+ &attached);
+ if (attached && cable_type == MAX14577_MUIC_ADC_FACTORY_MODE_UART_OFF)
+ max14577_muic_set_path(info, info->path_uart, true);
/* Check revision number of MUIC device*/
ret = max14577_read_reg(info->max14577->regmap,
diff --git a/drivers/extcon/extcon-max3355.c b/drivers/extcon/extcon-max3355.c
index 1335a47..fa01926 100644
--- a/drivers/extcon/extcon-max3355.c
+++ b/drivers/extcon/extcon-max3355.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
/*
* Maxim Integrated MAX3355 USB OTG chip extcon driver
*
* Copyright (C) 2014-2015 Cogent Embedded, Inc.
* Author: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
*/
#include <linux/extcon-provider.h>
diff --git a/drivers/extcon/extcon-max77693.c b/drivers/extcon/extcon-max77693.c
index 227651f..32fc5a6 100644
--- a/drivers/extcon/extcon-max77693.c
+++ b/drivers/extcon/extcon-max77693.c
@@ -1,19 +1,9 @@
-/*
- * extcon-max77693.c - MAX77693 extcon driver to support MAX77693 MUIC
- *
- * Copyright (C) 2012 Samsung Electrnoics
- * Chanwoo Choi <cw00.choi@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0+
+//
+// extcon-max77693.c - MAX77693 extcon driver to support MAX77693 MUIC
+//
+// Copyright (C) 2012 Samsung Electrnoics
+// Chanwoo Choi <cw00.choi@samsung.com>
#include <linux/kernel.h>
#include <linux/module.h>
@@ -1082,6 +1072,8 @@
struct max77693_reg_data *init_data;
int num_init_data;
int delay_jiffies;
+ int cable_type;
+ bool attached;
int ret;
int i;
unsigned int id;
@@ -1222,8 +1214,18 @@
delay_jiffies = msecs_to_jiffies(DELAY_MS_DEFAULT);
}
- /* Set initial path for UART */
- max77693_muic_set_path(info, info->path_uart, true);
+ /* Set initial path for UART when JIG is connected to get serial logs */
+ ret = regmap_bulk_read(info->max77693->regmap_muic,
+ MAX77693_MUIC_REG_STATUS1, info->status, 2);
+ if (ret) {
+ dev_err(info->dev, "failed to read MUIC register\n");
+ return ret;
+ }
+ cable_type = max77693_muic_get_cable_type(info,
+ MAX77693_CABLE_GROUP_ADC, &attached);
+ if (attached && (cable_type == MAX77693_MUIC_ADC_FACTORY_MODE_UART_ON ||
+ cable_type == MAX77693_MUIC_ADC_FACTORY_MODE_UART_OFF))
+ max77693_muic_set_path(info, info->path_uart, true);
/* Check revision number of MUIC device*/
ret = regmap_read(info->max77693->regmap_muic,
diff --git a/drivers/extcon/extcon-max77843.c b/drivers/extcon/extcon-max77843.c
index c9fcd6c..e6b50ca 100644
--- a/drivers/extcon/extcon-max77843.c
+++ b/drivers/extcon/extcon-max77843.c
@@ -1,15 +1,10 @@
-/*
- * extcon-max77843.c - Maxim MAX77843 extcon driver to support
- * MUIC(Micro USB Interface Controller)
- *
- * Copyright (C) 2015 Samsung Electronics
- * Author: Jaewon Kim <jaewon02.kim@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
+// SPDX-License-Identifier: GPL-2.0+
+//
+// extcon-max77843.c - Maxim MAX77843 extcon driver to support
+// MUIC(Micro USB Interface Controller)
+//
+// Copyright (C) 2015 Samsung Electronics
+// Author: Jaewon Kim <jaewon02.kim@samsung.com>
#include <linux/extcon-provider.h>
#include <linux/i2c.h>
@@ -779,12 +774,12 @@
{
int ret;
- max77843->i2c_muic = i2c_new_dummy(max77843->i2c->adapter,
+ max77843->i2c_muic = i2c_new_dummy_device(max77843->i2c->adapter,
I2C_ADDR_MUIC);
- if (!max77843->i2c_muic) {
+ if (IS_ERR(max77843->i2c_muic)) {
dev_err(&max77843->i2c->dev,
"Cannot allocate I2C device for MUIC\n");
- return -ENOMEM;
+ return PTR_ERR(max77843->i2c_muic);
}
i2c_set_clientdata(max77843->i2c_muic, max77843);
@@ -817,6 +812,8 @@
struct max77693_dev *max77843 = dev_get_drvdata(pdev->dev.parent);
struct max77843_muic_info *info;
unsigned int id;
+ int cable_type;
+ bool attached;
int i, ret;
info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
@@ -861,9 +858,19 @@
/* Set ADC debounce time */
max77843_muic_set_debounce_time(info, MAX77843_DEBOUNCE_TIME_25MS);
- /* Set initial path for UART */
- max77843_muic_set_path(info, MAX77843_MUIC_CONTROL1_SW_UART, true,
- false);
+ /* Set initial path for UART when JIG is connected to get serial logs */
+ ret = regmap_bulk_read(max77843->regmap_muic,
+ MAX77843_MUIC_REG_STATUS1, info->status,
+ MAX77843_MUIC_STATUS_NUM);
+ if (ret) {
+ dev_err(info->dev, "Cannot read STATUS registers\n");
+ goto err_muic_irq;
+ }
+ cable_type = max77843_muic_get_cable_type(info, MAX77843_CABLE_GROUP_ADC,
+ &attached);
+ if (attached && cable_type == MAX77843_MUIC_ADC_FACTORY_MODE_UART_OFF)
+ max77843_muic_set_path(info, MAX77843_MUIC_CONTROL1_SW_UART,
+ true, false);
/* Check revision number of MUIC device */
ret = regmap_read(max77843->regmap_muic, MAX77843_MUIC_REG_ID, &id);
diff --git a/drivers/extcon/extcon-max8997.c b/drivers/extcon/extcon-max8997.c
index 9f30f49..172e116 100644
--- a/drivers/extcon/extcon-max8997.c
+++ b/drivers/extcon/extcon-max8997.c
@@ -1,19 +1,9 @@
-/*
- * extcon-max8997.c - MAX8997 extcon driver to support MAX8997 MUIC
- *
- * Copyright (C) 2012 Samsung Electronics
- * Donggeun Kim <dg77.kim@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0+
+//
+// extcon-max8997.c - MAX8997 extcon driver to support MAX8997 MUIC
+//
+// Copyright (C) 2012 Samsung Electronics
+// Donggeun Kim <dg77.kim@samsung.com>
#include <linux/kernel.h>
#include <linux/module.h>
@@ -321,12 +311,10 @@
{
int ret = 0;
- if (usb_type == MAX8997_USB_HOST) {
- ret = max8997_muic_set_path(info, info->path_usb, attached);
- if (ret < 0) {
- dev_err(info->dev, "failed to update muic register\n");
- return ret;
- }
+ ret = max8997_muic_set_path(info, info->path_usb, attached);
+ if (ret < 0) {
+ dev_err(info->dev, "failed to update muic register\n");
+ return ret;
}
switch (usb_type) {
@@ -642,6 +630,8 @@
struct max8997_platform_data *pdata = dev_get_platdata(max8997->dev);
struct max8997_muic_info *info;
int delay_jiffies;
+ int cable_type;
+ bool attached;
int ret, i;
info = devm_kzalloc(&pdev->dev, sizeof(struct max8997_muic_info),
@@ -734,8 +724,17 @@
delay_jiffies = msecs_to_jiffies(DELAY_MS_DEFAULT);
}
- /* Set initial path for UART */
- max8997_muic_set_path(info, info->path_uart, true);
+ /* Set initial path for UART when JIG is connected to get serial logs */
+ ret = max8997_bulk_read(info->muic, MAX8997_MUIC_REG_STATUS1,
+ 2, info->status);
+ if (ret) {
+ dev_err(info->dev, "failed to read MUIC register\n");
+ return ret;
+ }
+ cable_type = max8997_muic_get_cable_type(info,
+ MAX8997_CABLE_GROUP_ADC, &attached);
+ if (attached && cable_type == MAX8997_MUIC_ADC_FACTORY_MODE_UART_OFF)
+ max8997_muic_set_path(info, info->path_uart, true);
/* Set ADC debounce time */
max8997_muic_set_debounce_time(info, ADC_DEBOUNCE_TIME_25MS);
diff --git a/drivers/extcon/extcon-palmas.c b/drivers/extcon/extcon-palmas.c
index 2af4369..edc5016 100644
--- a/drivers/extcon/extcon-palmas.c
+++ b/drivers/extcon/extcon-palmas.c
@@ -1,23 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Palmas USB transceiver driver
*
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
* Author: Graeme Gregory <gg@slimlogic.co.uk>
* Author: Kishon Vijay Abraham I <kishon@ti.com>
- *
* Based on twl6030_usb.c
- *
* Author: Hema HK <hemahk@ti.com>
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include <linux/module.h>
diff --git a/drivers/extcon/extcon-ptn5150.c b/drivers/extcon/extcon-ptn5150.c
new file mode 100644
index 0000000..d1c9975
--- /dev/null
+++ b/drivers/extcon/extcon-ptn5150.c
@@ -0,0 +1,339 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// extcon-ptn5150.c - PTN5150 CC logic extcon driver to support USB detection
+//
+// Based on extcon-sm5502.c driver
+// Copyright (c) 2018-2019 by Vijai Kumar K
+// Author: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/extcon-provider.h>
+#include <linux/gpio/consumer.h>
+
+/* PTN5150 registers */
+enum ptn5150_reg {
+ PTN5150_REG_DEVICE_ID = 0x01,
+ PTN5150_REG_CONTROL,
+ PTN5150_REG_INT_STATUS,
+ PTN5150_REG_CC_STATUS,
+ PTN5150_REG_CON_DET = 0x09,
+ PTN5150_REG_VCONN_STATUS,
+ PTN5150_REG_RESET,
+ PTN5150_REG_INT_MASK = 0x18,
+ PTN5150_REG_INT_REG_STATUS,
+ PTN5150_REG_END,
+};
+
+#define PTN5150_DFP_ATTACHED 0x1
+#define PTN5150_UFP_ATTACHED 0x2
+
+/* Define PTN5150 MASK/SHIFT constant */
+#define PTN5150_REG_DEVICE_ID_VENDOR_SHIFT 0
+#define PTN5150_REG_DEVICE_ID_VENDOR_MASK \
+ (0x3 << PTN5150_REG_DEVICE_ID_VENDOR_SHIFT)
+
+#define PTN5150_REG_DEVICE_ID_VERSION_SHIFT 3
+#define PTN5150_REG_DEVICE_ID_VERSION_MASK \
+ (0x1f << PTN5150_REG_DEVICE_ID_VERSION_SHIFT)
+
+#define PTN5150_REG_CC_PORT_ATTACHMENT_SHIFT 2
+#define PTN5150_REG_CC_PORT_ATTACHMENT_MASK \
+ (0x7 << PTN5150_REG_CC_PORT_ATTACHMENT_SHIFT)
+
+#define PTN5150_REG_CC_VBUS_DETECTION_SHIFT 7
+#define PTN5150_REG_CC_VBUS_DETECTION_MASK \
+ (0x1 << PTN5150_REG_CC_VBUS_DETECTION_SHIFT)
+
+#define PTN5150_REG_INT_CABLE_ATTACH_SHIFT 0
+#define PTN5150_REG_INT_CABLE_ATTACH_MASK \
+ (0x1 << PTN5150_REG_INT_CABLE_ATTACH_SHIFT)
+
+#define PTN5150_REG_INT_CABLE_DETACH_SHIFT 1
+#define PTN5150_REG_INT_CABLE_DETACH_MASK \
+ (0x1 << PTN5150_REG_CC_CABLE_DETACH_SHIFT)
+
+struct ptn5150_info {
+ struct device *dev;
+ struct extcon_dev *edev;
+ struct i2c_client *i2c;
+ struct regmap *regmap;
+ struct gpio_desc *int_gpiod;
+ struct gpio_desc *vbus_gpiod;
+ int irq;
+ struct work_struct irq_work;
+ struct mutex mutex;
+};
+
+/* List of detectable cables */
+static const unsigned int ptn5150_extcon_cable[] = {
+ EXTCON_USB,
+ EXTCON_USB_HOST,
+ EXTCON_NONE,
+};
+
+static const struct regmap_config ptn5150_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = PTN5150_REG_END,
+};
+
+static void ptn5150_irq_work(struct work_struct *work)
+{
+ struct ptn5150_info *info = container_of(work,
+ struct ptn5150_info, irq_work);
+ int ret = 0;
+ unsigned int reg_data;
+ unsigned int int_status;
+
+ if (!info->edev)
+ return;
+
+ mutex_lock(&info->mutex);
+
+ ret = regmap_read(info->regmap, PTN5150_REG_CC_STATUS, ®_data);
+ if (ret) {
+ dev_err(info->dev, "failed to read CC STATUS %d\n", ret);
+ mutex_unlock(&info->mutex);
+ return;
+ }
+
+ /* Clear interrupt. Read would clear the register */
+ ret = regmap_read(info->regmap, PTN5150_REG_INT_STATUS, &int_status);
+ if (ret) {
+ dev_err(info->dev, "failed to read INT STATUS %d\n", ret);
+ mutex_unlock(&info->mutex);
+ return;
+ }
+
+ if (int_status) {
+ unsigned int cable_attach;
+
+ cable_attach = int_status & PTN5150_REG_INT_CABLE_ATTACH_MASK;
+ if (cable_attach) {
+ unsigned int port_status;
+ unsigned int vbus;
+
+ port_status = ((reg_data &
+ PTN5150_REG_CC_PORT_ATTACHMENT_MASK) >>
+ PTN5150_REG_CC_PORT_ATTACHMENT_SHIFT);
+
+ switch (port_status) {
+ case PTN5150_DFP_ATTACHED:
+ extcon_set_state_sync(info->edev,
+ EXTCON_USB_HOST, false);
+ gpiod_set_value(info->vbus_gpiod, 0);
+ extcon_set_state_sync(info->edev, EXTCON_USB,
+ true);
+ break;
+ case PTN5150_UFP_ATTACHED:
+ extcon_set_state_sync(info->edev, EXTCON_USB,
+ false);
+ vbus = ((reg_data &
+ PTN5150_REG_CC_VBUS_DETECTION_MASK) >>
+ PTN5150_REG_CC_VBUS_DETECTION_SHIFT);
+ if (vbus)
+ gpiod_set_value(info->vbus_gpiod, 0);
+ else
+ gpiod_set_value(info->vbus_gpiod, 1);
+
+ extcon_set_state_sync(info->edev,
+ EXTCON_USB_HOST, true);
+ break;
+ default:
+ dev_err(info->dev,
+ "Unknown Port status : %x\n",
+ port_status);
+ break;
+ }
+ } else {
+ extcon_set_state_sync(info->edev,
+ EXTCON_USB_HOST, false);
+ extcon_set_state_sync(info->edev,
+ EXTCON_USB, false);
+ gpiod_set_value(info->vbus_gpiod, 0);
+ }
+ }
+
+ /* Clear interrupt. Read would clear the register */
+ ret = regmap_read(info->regmap, PTN5150_REG_INT_REG_STATUS,
+ &int_status);
+ if (ret) {
+ dev_err(info->dev,
+ "failed to read INT REG STATUS %d\n", ret);
+ mutex_unlock(&info->mutex);
+ return;
+ }
+
+ mutex_unlock(&info->mutex);
+}
+
+
+static irqreturn_t ptn5150_irq_handler(int irq, void *data)
+{
+ struct ptn5150_info *info = data;
+
+ schedule_work(&info->irq_work);
+
+ return IRQ_HANDLED;
+}
+
+static int ptn5150_init_dev_type(struct ptn5150_info *info)
+{
+ unsigned int reg_data, vendor_id, version_id;
+ int ret;
+
+ ret = regmap_read(info->regmap, PTN5150_REG_DEVICE_ID, ®_data);
+ if (ret) {
+ dev_err(info->dev, "failed to read DEVICE_ID %d\n", ret);
+ return -EINVAL;
+ }
+
+ vendor_id = ((reg_data & PTN5150_REG_DEVICE_ID_VENDOR_MASK) >>
+ PTN5150_REG_DEVICE_ID_VENDOR_SHIFT);
+ version_id = ((reg_data & PTN5150_REG_DEVICE_ID_VERSION_MASK) >>
+ PTN5150_REG_DEVICE_ID_VERSION_SHIFT);
+
+ dev_info(info->dev, "Device type: version: 0x%x, vendor: 0x%x\n",
+ version_id, vendor_id);
+
+ /* Clear any existing interrupts */
+ ret = regmap_read(info->regmap, PTN5150_REG_INT_STATUS, ®_data);
+ if (ret) {
+ dev_err(info->dev,
+ "failed to read PTN5150_REG_INT_STATUS %d\n",
+ ret);
+ return -EINVAL;
+ }
+
+ ret = regmap_read(info->regmap, PTN5150_REG_INT_REG_STATUS, ®_data);
+ if (ret) {
+ dev_err(info->dev,
+ "failed to read PTN5150_REG_INT_REG_STATUS %d\n", ret);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int ptn5150_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &i2c->dev;
+ struct device_node *np = i2c->dev.of_node;
+ struct ptn5150_info *info;
+ int ret;
+
+ if (!np)
+ return -EINVAL;
+
+ info = devm_kzalloc(&i2c->dev, sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+ i2c_set_clientdata(i2c, info);
+
+ info->dev = &i2c->dev;
+ info->i2c = i2c;
+ info->int_gpiod = devm_gpiod_get(&i2c->dev, "int", GPIOD_IN);
+ if (IS_ERR(info->int_gpiod)) {
+ dev_err(dev, "failed to get INT GPIO\n");
+ return PTR_ERR(info->int_gpiod);
+ }
+ info->vbus_gpiod = devm_gpiod_get(&i2c->dev, "vbus", GPIOD_IN);
+ if (IS_ERR(info->vbus_gpiod)) {
+ dev_err(dev, "failed to get VBUS GPIO\n");
+ return PTR_ERR(info->vbus_gpiod);
+ }
+ ret = gpiod_direction_output(info->vbus_gpiod, 0);
+ if (ret) {
+ dev_err(dev, "failed to set VBUS GPIO direction\n");
+ return -EINVAL;
+ }
+
+ mutex_init(&info->mutex);
+
+ INIT_WORK(&info->irq_work, ptn5150_irq_work);
+
+ info->regmap = devm_regmap_init_i2c(i2c, &ptn5150_regmap_config);
+ if (IS_ERR(info->regmap)) {
+ ret = PTR_ERR(info->regmap);
+ dev_err(info->dev, "failed to allocate register map: %d\n",
+ ret);
+ return ret;
+ }
+
+ if (info->int_gpiod) {
+ info->irq = gpiod_to_irq(info->int_gpiod);
+ if (info->irq < 0) {
+ dev_err(dev, "failed to get INTB IRQ\n");
+ return info->irq;
+ }
+
+ ret = devm_request_threaded_irq(dev, info->irq, NULL,
+ ptn5150_irq_handler,
+ IRQF_TRIGGER_FALLING |
+ IRQF_ONESHOT,
+ i2c->name, info);
+ if (ret < 0) {
+ dev_err(dev, "failed to request handler for INTB IRQ\n");
+ return ret;
+ }
+ }
+
+ /* Allocate extcon device */
+ info->edev = devm_extcon_dev_allocate(info->dev, ptn5150_extcon_cable);
+ if (IS_ERR(info->edev)) {
+ dev_err(info->dev, "failed to allocate memory for extcon\n");
+ return -ENOMEM;
+ }
+
+ /* Register extcon device */
+ ret = devm_extcon_dev_register(info->dev, info->edev);
+ if (ret) {
+ dev_err(info->dev, "failed to register extcon device\n");
+ return ret;
+ }
+
+ /* Initialize PTN5150 device and print vendor id and version id */
+ ret = ptn5150_init_dev_type(info);
+ if (ret)
+ return -EINVAL;
+
+ return 0;
+}
+
+static const struct of_device_id ptn5150_dt_match[] = {
+ { .compatible = "nxp,ptn5150" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, ptn5150_dt_match);
+
+static const struct i2c_device_id ptn5150_i2c_id[] = {
+ { "ptn5150", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, ptn5150_i2c_id);
+
+static struct i2c_driver ptn5150_i2c_driver = {
+ .driver = {
+ .name = "ptn5150",
+ .of_match_table = ptn5150_dt_match,
+ },
+ .probe = ptn5150_i2c_probe,
+ .id_table = ptn5150_i2c_id,
+};
+
+static int __init ptn5150_i2c_init(void)
+{
+ return i2c_add_driver(&ptn5150_i2c_driver);
+}
+subsys_initcall(ptn5150_i2c_init);
+
+MODULE_DESCRIPTION("NXP PTN5150 CC logic Extcon driver");
+MODULE_AUTHOR("Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/extcon/extcon-qcom-spmi-misc.c b/drivers/extcon/extcon-qcom-spmi-misc.c
index 72bc0f2..6b836ae 100644
--- a/drivers/extcon/extcon-qcom-spmi-misc.c
+++ b/drivers/extcon/extcon-qcom-spmi-misc.c
@@ -1,18 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
/**
* extcon-qcom-spmi-misc.c - Qualcomm USB extcon driver to support USB ID
* detection based on extcon-usb-gpio.c.
*
* Copyright (C) 2016 Linaro, Ltd.
* Stephen Boyd <stephen.boyd@linaro.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include <linux/extcon-provider.h>
diff --git a/drivers/extcon/extcon-rt8973a.c b/drivers/extcon/extcon-rt8973a.c
index e059bd5..40c07f4 100644
--- a/drivers/extcon/extcon-rt8973a.c
+++ b/drivers/extcon/extcon-rt8973a.c
@@ -1,13 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
/*
* extcon-rt8973a.c - Richtek RT8973A extcon driver to support USB switches
*
* Copyright (c) 2014 Samsung Electronics Co., Ltd
* Author: Chanwoo Choi <cw00.choi@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
*/
#include <linux/err.h>
diff --git a/drivers/extcon/extcon-rt8973a.h b/drivers/extcon/extcon-rt8973a.h
index 9dc3e02..0d0d69f 100644
--- a/drivers/extcon/extcon-rt8973a.h
+++ b/drivers/extcon/extcon-rt8973a.h
@@ -1,12 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* rt8973a.h
*
* Copyright (c) 2014 Samsung Electronics Co., Ltd
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
*/
#ifndef __LINUX_EXTCON_RT8973A_H
diff --git a/drivers/extcon/extcon-sm5502.c b/drivers/extcon/extcon-sm5502.c
index 0cfb5a3..dc43847 100644
--- a/drivers/extcon/extcon-sm5502.c
+++ b/drivers/extcon/extcon-sm5502.c
@@ -1,13 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
/*
* extcon-sm5502.c - Silicon Mitus SM5502 extcon drvier to support USB switches
*
* Copyright (c) 2014 Samsung Electronics Co., Ltd
* Author: Chanwoo Choi <cw00.choi@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
*/
#include <linux/err.h>
@@ -601,7 +597,7 @@
ret = devm_request_threaded_irq(info->dev, virq, NULL,
sm5502_muic_irq_handler,
- IRQF_NO_SUSPEND,
+ IRQF_NO_SUSPEND | IRQF_ONESHOT,
muic_irq->name, info);
if (ret) {
dev_err(info->dev,
diff --git a/drivers/extcon/extcon-sm5502.h b/drivers/extcon/extcon-sm5502.h
index 974b532..9dbb634 100644
--- a/drivers/extcon/extcon-sm5502.h
+++ b/drivers/extcon/extcon-sm5502.h
@@ -1,12 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* sm5502.h
*
* Copyright (c) 2014 Samsung Electronics Co., Ltd
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
*/
#ifndef __LINUX_EXTCON_SM5502_H
diff --git a/drivers/extcon/extcon-usb-gpio.c b/drivers/extcon/extcon-usb-gpio.c
index 5376286..98b5afa 100644
--- a/drivers/extcon/extcon-usb-gpio.c
+++ b/drivers/extcon/extcon-usb-gpio.c
@@ -1,17 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
/**
* drivers/extcon/extcon-usb-gpio.c - USB GPIO extcon driver
*
* Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com
* Author: Roger Quadros <rogerq@ti.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include <linux/extcon-provider.h>
diff --git a/drivers/extcon/extcon-usbc-cros-ec.c b/drivers/extcon/extcon-usbc-cros-ec.c
index 43c0a93..5290cc2 100644
--- a/drivers/extcon/extcon-usbc-cros-ec.c
+++ b/drivers/extcon/extcon-usbc-cros-ec.c
@@ -6,10 +6,11 @@
#include <linux/extcon-provider.h>
#include <linux/kernel.h>
-#include <linux/mfd/cros_ec.h>
#include <linux/module.h>
#include <linux/notifier.h>
#include <linux/of.h>
+#include <linux/platform_data/cros_ec_commands.h>
+#include <linux/platform_data/cros_ec_proto.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/sched.h>
diff --git a/drivers/extcon/extcon.c b/drivers/extcon/extcon.c
index b9d27c8..e055893 100644
--- a/drivers/extcon/extcon.c
+++ b/drivers/extcon/extcon.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
/*
* drivers/extcon/extcon.c - External Connector (extcon) framework.
*
@@ -11,15 +12,6 @@
* based on android/drivers/switch/switch_class.c
* Copyright (C) 2008 Google, Inc.
* Author: Mike Lockwood <lockwood@android.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include <linux/module.h>
@@ -628,7 +620,7 @@
unsigned long flags;
int index, ret = 0;
- *prop_val = (union extcon_property_value)(0);
+ *prop_val = (union extcon_property_value){0};
if (!edev)
return -EINVAL;
@@ -1123,7 +1115,6 @@
(unsigned long)atomic_inc_return(&edev_no));
if (edev->max_supported) {
- char buf[10];
char *str;
struct extcon_cable *cable;
@@ -1137,9 +1128,7 @@
for (index = 0; index < edev->max_supported; index++) {
cable = &edev->cables[index];
- snprintf(buf, 10, "cable.%d", index);
- str = kzalloc(strlen(buf) + 1,
- GFP_KERNEL);
+ str = kasprintf(GFP_KERNEL, "cable.%d", index);
if (!str) {
for (index--; index >= 0; index--) {
cable = &edev->cables[index];
@@ -1149,7 +1138,6 @@
goto err_alloc_cables;
}
- strcpy(str, buf);
cable->edev = edev;
cable->cable_index = index;
@@ -1172,7 +1160,6 @@
}
if (edev->max_supported && edev->mutually_exclusive) {
- char buf[80];
char *name;
/* Count the size of mutually_exclusive array */
@@ -1197,9 +1184,8 @@
}
for (index = 0; edev->mutually_exclusive[index]; index++) {
- sprintf(buf, "0x%x", edev->mutually_exclusive[index]);
- name = kzalloc(strlen(buf) + 1,
- GFP_KERNEL);
+ name = kasprintf(GFP_KERNEL, "0x%x",
+ edev->mutually_exclusive[index]);
if (!name) {
for (index--; index >= 0; index--) {
kfree(edev->d_attrs_muex[index].attr.
@@ -1210,7 +1196,6 @@
ret = -ENOMEM;
goto err_muex;
}
- strcpy(name, buf);
sysfs_attr_init(&edev->d_attrs_muex[index].attr);
edev->d_attrs_muex[index].attr.name = name;
edev->d_attrs_muex[index].attr.mode = 0000;