Update Linux to v5.4.2
Change-Id: Idf6911045d9d382da2cfe01b1edff026404ac8fd
diff --git a/Documentation/sparc/adi.rst b/Documentation/sparc/adi.rst
new file mode 100644
index 0000000..857ad30
--- /dev/null
+++ b/Documentation/sparc/adi.rst
@@ -0,0 +1,286 @@
+================================
+Application Data Integrity (ADI)
+================================
+
+SPARC M7 processor adds the Application Data Integrity (ADI) feature.
+ADI allows a task to set version tags on any subset of its address
+space. Once ADI is enabled and version tags are set for ranges of
+address space of a task, the processor will compare the tag in pointers
+to memory in these ranges to the version set by the application
+previously. Access to memory is granted only if the tag in given pointer
+matches the tag set by the application. In case of mismatch, processor
+raises an exception.
+
+Following steps must be taken by a task to enable ADI fully:
+
+1. Set the user mode PSTATE.mcde bit. This acts as master switch for
+ the task's entire address space to enable/disable ADI for the task.
+
+2. Set TTE.mcd bit on any TLB entries that correspond to the range of
+ addresses ADI is being enabled on. MMU checks the version tag only
+ on the pages that have TTE.mcd bit set.
+
+3. Set the version tag for virtual addresses using stxa instruction
+ and one of the MCD specific ASIs. Each stxa instruction sets the
+ given tag for one ADI block size number of bytes. This step must
+ be repeated for entire page to set tags for entire page.
+
+ADI block size for the platform is provided by the hypervisor to kernel
+in machine description tables. Hypervisor also provides the number of
+top bits in the virtual address that specify the version tag. Once
+version tag has been set for a memory location, the tag is stored in the
+physical memory and the same tag must be present in the ADI version tag
+bits of the virtual address being presented to the MMU. For example on
+SPARC M7 processor, MMU uses bits 63-60 for version tags and ADI block
+size is same as cacheline size which is 64 bytes. A task that sets ADI
+version to, say 10, on a range of memory, must access that memory using
+virtual addresses that contain 0xa in bits 63-60.
+
+ADI is enabled on a set of pages using mprotect() with PROT_ADI flag.
+When ADI is enabled on a set of pages by a task for the first time,
+kernel sets the PSTATE.mcde bit fot the task. Version tags for memory
+addresses are set with an stxa instruction on the addresses using
+ASI_MCD_PRIMARY or ASI_MCD_ST_BLKINIT_PRIMARY. ADI block size is
+provided by the hypervisor to the kernel. Kernel returns the value of
+ADI block size to userspace using auxiliary vector along with other ADI
+info. Following auxiliary vectors are provided by the kernel:
+
+ ============ ===========================================
+ AT_ADI_BLKSZ ADI block size. This is the granularity and
+ alignment, in bytes, of ADI versioning.
+ AT_ADI_NBITS Number of ADI version bits in the VA
+ ============ ===========================================
+
+
+IMPORTANT NOTES
+===============
+
+- Version tag values of 0x0 and 0xf are reserved. These values match any
+ tag in virtual address and never generate a mismatch exception.
+
+- Version tags are set on virtual addresses from userspace even though
+ tags are stored in physical memory. Tags are set on a physical page
+ after it has been allocated to a task and a pte has been created for
+ it.
+
+- When a task frees a memory page it had set version tags on, the page
+ goes back to free page pool. When this page is re-allocated to a task,
+ kernel clears the page using block initialization ASI which clears the
+ version tags as well for the page. If a page allocated to a task is
+ freed and allocated back to the same task, old version tags set by the
+ task on that page will no longer be present.
+
+- ADI tag mismatches are not detected for non-faulting loads.
+
+- Kernel does not set any tags for user pages and it is entirely a
+ task's responsibility to set any version tags. Kernel does ensure the
+ version tags are preserved if a page is swapped out to the disk and
+ swapped back in. It also preserves that version tags if a page is
+ migrated.
+
+- ADI works for any size pages. A userspace task need not be aware of
+ page size when using ADI. It can simply select a virtual address
+ range, enable ADI on the range using mprotect() and set version tags
+ for the entire range. mprotect() ensures range is aligned to page size
+ and is a multiple of page size.
+
+- ADI tags can only be set on writable memory. For example, ADI tags can
+ not be set on read-only mappings.
+
+
+
+ADI related traps
+=================
+
+With ADI enabled, following new traps may occur:
+
+Disrupting memory corruption
+----------------------------
+
+ When a store accesses a memory localtion that has TTE.mcd=1,
+ the task is running with ADI enabled (PSTATE.mcde=1), and the ADI
+ tag in the address used (bits 63:60) does not match the tag set on
+ the corresponding cacheline, a memory corruption trap occurs. By
+ default, it is a disrupting trap and is sent to the hypervisor
+ first. Hypervisor creates a sun4v error report and sends a
+ resumable error (TT=0x7e) trap to the kernel. The kernel sends
+ a SIGSEGV to the task that resulted in this trap with the following
+ info::
+
+ siginfo.si_signo = SIGSEGV;
+ siginfo.errno = 0;
+ siginfo.si_code = SEGV_ADIDERR;
+ siginfo.si_addr = addr; /* PC where first mismatch occurred */
+ siginfo.si_trapno = 0;
+
+
+Precise memory corruption
+-------------------------
+
+ When a store accesses a memory location that has TTE.mcd=1,
+ the task is running with ADI enabled (PSTATE.mcde=1), and the ADI
+ tag in the address used (bits 63:60) does not match the tag set on
+ the corresponding cacheline, a memory corruption trap occurs. If
+ MCD precise exception is enabled (MCDPERR=1), a precise
+ exception is sent to the kernel with TT=0x1a. The kernel sends
+ a SIGSEGV to the task that resulted in this trap with the following
+ info::
+
+ siginfo.si_signo = SIGSEGV;
+ siginfo.errno = 0;
+ siginfo.si_code = SEGV_ADIPERR;
+ siginfo.si_addr = addr; /* address that caused trap */
+ siginfo.si_trapno = 0;
+
+ NOTE:
+ ADI tag mismatch on a load always results in precise trap.
+
+
+MCD disabled
+------------
+
+ When a task has not enabled ADI and attempts to set ADI version
+ on a memory address, processor sends an MCD disabled trap. This
+ trap is handled by hypervisor first and the hypervisor vectors this
+ trap through to the kernel as Data Access Exception trap with
+ fault type set to 0xa (invalid ASI). When this occurs, the kernel
+ sends the task SIGSEGV signal with following info::
+
+ siginfo.si_signo = SIGSEGV;
+ siginfo.errno = 0;
+ siginfo.si_code = SEGV_ACCADI;
+ siginfo.si_addr = addr; /* address that caused trap */
+ siginfo.si_trapno = 0;
+
+
+Sample program to use ADI
+-------------------------
+
+Following sample program is meant to illustrate how to use the ADI
+functionality::
+
+ #include <unistd.h>
+ #include <stdio.h>
+ #include <stdlib.h>
+ #include <elf.h>
+ #include <sys/ipc.h>
+ #include <sys/shm.h>
+ #include <sys/mman.h>
+ #include <asm/asi.h>
+
+ #ifndef AT_ADI_BLKSZ
+ #define AT_ADI_BLKSZ 48
+ #endif
+ #ifndef AT_ADI_NBITS
+ #define AT_ADI_NBITS 49
+ #endif
+
+ #ifndef PROT_ADI
+ #define PROT_ADI 0x10
+ #endif
+
+ #define BUFFER_SIZE 32*1024*1024UL
+
+ main(int argc, char* argv[], char* envp[])
+ {
+ unsigned long i, mcde, adi_blksz, adi_nbits;
+ char *shmaddr, *tmp_addr, *end, *veraddr, *clraddr;
+ int shmid, version;
+ Elf64_auxv_t *auxv;
+
+ adi_blksz = 0;
+
+ while(*envp++ != NULL);
+ for (auxv = (Elf64_auxv_t *)envp; auxv->a_type != AT_NULL; auxv++) {
+ switch (auxv->a_type) {
+ case AT_ADI_BLKSZ:
+ adi_blksz = auxv->a_un.a_val;
+ break;
+ case AT_ADI_NBITS:
+ adi_nbits = auxv->a_un.a_val;
+ break;
+ }
+ }
+ if (adi_blksz == 0) {
+ fprintf(stderr, "Oops! ADI is not supported\n");
+ exit(1);
+ }
+
+ printf("ADI capabilities:\n");
+ printf("\tBlock size = %ld\n", adi_blksz);
+ printf("\tNumber of bits = %ld\n", adi_nbits);
+
+ if ((shmid = shmget(2, BUFFER_SIZE,
+ IPC_CREAT | SHM_R | SHM_W)) < 0) {
+ perror("shmget failed");
+ exit(1);
+ }
+
+ shmaddr = shmat(shmid, NULL, 0);
+ if (shmaddr == (char *)-1) {
+ perror("shm attach failed");
+ shmctl(shmid, IPC_RMID, NULL);
+ exit(1);
+ }
+
+ if (mprotect(shmaddr, BUFFER_SIZE, PROT_READ|PROT_WRITE|PROT_ADI)) {
+ perror("mprotect failed");
+ goto err_out;
+ }
+
+ /* Set the ADI version tag on the shm segment
+ */
+ version = 10;
+ tmp_addr = shmaddr;
+ end = shmaddr + BUFFER_SIZE;
+ while (tmp_addr < end) {
+ asm volatile(
+ "stxa %1, [%0]0x90\n\t"
+ :
+ : "r" (tmp_addr), "r" (version));
+ tmp_addr += adi_blksz;
+ }
+ asm volatile("membar #Sync\n\t");
+
+ /* Create a versioned address from the normal address by placing
+ * version tag in the upper adi_nbits bits
+ */
+ tmp_addr = (void *) ((unsigned long)shmaddr << adi_nbits);
+ tmp_addr = (void *) ((unsigned long)tmp_addr >> adi_nbits);
+ veraddr = (void *) (((unsigned long)version << (64-adi_nbits))
+ | (unsigned long)tmp_addr);
+
+ printf("Starting the writes:\n");
+ for (i = 0; i < BUFFER_SIZE; i++) {
+ veraddr[i] = (char)(i);
+ if (!(i % (1024 * 1024)))
+ printf(".");
+ }
+ printf("\n");
+
+ printf("Verifying data...");
+ fflush(stdout);
+ for (i = 0; i < BUFFER_SIZE; i++)
+ if (veraddr[i] != (char)i)
+ printf("\nIndex %lu mismatched\n", i);
+ printf("Done.\n");
+
+ /* Disable ADI and clean up
+ */
+ if (mprotect(shmaddr, BUFFER_SIZE, PROT_READ|PROT_WRITE)) {
+ perror("mprotect failed");
+ goto err_out;
+ }
+
+ if (shmdt((const void *)shmaddr) != 0)
+ perror("Detach failure");
+ shmctl(shmid, IPC_RMID, NULL);
+
+ exit(0);
+
+ err_out:
+ if (shmdt((const void *)shmaddr) != 0)
+ perror("Detach failure");
+ shmctl(shmid, IPC_RMID, NULL);
+ exit(1);
+ }