Update Linux to v5.4.2
Change-Id: Idf6911045d9d382da2cfe01b1edff026404ac8fd
diff --git a/Documentation/misc-devices/eeprom b/Documentation/misc-devices/eeprom.rst
similarity index 76%
rename from Documentation/misc-devices/eeprom
rename to Documentation/misc-devices/eeprom.rst
index ba69201..0082496 100644
--- a/Documentation/misc-devices/eeprom
+++ b/Documentation/misc-devices/eeprom.rst
@@ -1,11 +1,17 @@
+====================
Kernel driver eeprom
====================
Supported chips:
+
* Any EEPROM chip in the designated address range
+
Prefix: 'eeprom'
+
Addresses scanned: I2C 0x50 - 0x57
+
Datasheets: Publicly available from:
+
Atmel (www.atmel.com),
Catalyst (www.catsemi.com),
Fairchild (www.fairchildsemi.com),
@@ -16,7 +22,9 @@
Xicor (www.xicor.com),
and others.
- Chip Size (bits) Address
+ ========= ============= ============================================
+ Chip Size (bits) Address
+ ========= ============= ============================================
24C01 1K 0x50 (shadows at 0x51 - 0x57)
24C01A 1K 0x50 - 0x57 (Typical device on DIMMs)
24C02 2K 0x50 - 0x57
@@ -24,7 +32,7 @@
(additional data at 0x51, 0x53, 0x55, 0x57)
24C08 8K 0x50, 0x54 (additional data at 0x51, 0x52,
0x53, 0x55, 0x56, 0x57)
- 24C16 16K 0x50 (additional data at 0x51 - 0x57)
+ 24C16 16K 0x50 (additional data at 0x51 - 0x57)
Sony 2K 0x57
Atmel 34C02B 2K 0x50 - 0x57, SW write protect at 0x30-37
@@ -33,14 +41,15 @@
Fairchild 34W02 2K 0x50 - 0x57, SW write protect at 0x30-37
Microchip 24AA52 2K 0x50 - 0x57, SW write protect at 0x30-37
ST M34C02 2K 0x50 - 0x57, SW write protect at 0x30-37
+ ========= ============= ============================================
Authors:
- Frodo Looijaard <frodol@dds.nl>,
- Philip Edelbrock <phil@netroedge.com>,
- Jean Delvare <jdelvare@suse.de>,
- Greg Kroah-Hartman <greg@kroah.com>,
- IBM Corp.
+ - Frodo Looijaard <frodol@dds.nl>,
+ - Philip Edelbrock <phil@netroedge.com>,
+ - Jean Delvare <jdelvare@suse.de>,
+ - Greg Kroah-Hartman <greg@kroah.com>,
+ - IBM Corp.
Description
-----------
@@ -74,23 +83,25 @@
device will no longer respond at the 0x30-37 address. The eeprom driver
does not support this register.
-Lacking functionality:
+Lacking functionality
+---------------------
* Full support for larger devices (24C04, 24C08, 24C16). These are not
-typically found on a PC. These devices will appear as separate devices at
-multiple addresses.
+ typically found on a PC. These devices will appear as separate devices at
+ multiple addresses.
* Support for really large devices (24C32, 24C64, 24C128, 24C256, 24C512).
-These devices require two-byte address fields and are not supported.
+ These devices require two-byte address fields and are not supported.
* Enable Writing. Again, no technical reason why not, but making it easy
-to change the contents of the EEPROMs (on DIMMs anyway) also makes it easy
-to disable the DIMMs (potentially preventing the computer from booting)
-until the values are restored somehow.
+ to change the contents of the EEPROMs (on DIMMs anyway) also makes it easy
+ to disable the DIMMs (potentially preventing the computer from booting)
+ until the values are restored somehow.
-Use:
+Use
+---
After inserting the module (and any other required SMBus/i2c modules), you
-should have some EEPROM directories in /sys/bus/i2c/devices/* of names such
+should have some EEPROM directories in ``/sys/bus/i2c/devices/*`` of names such
as "0-0050". Inside each of these is a series of files, the eeprom file
contains the binary data from EEPROM.
diff --git a/Documentation/misc-devices/ibmvmc.rst b/Documentation/misc-devices/ibmvmc.rst
index 46ded79..b46df4e 100644
--- a/Documentation/misc-devices/ibmvmc.rst
+++ b/Documentation/misc-devices/ibmvmc.rst
@@ -1,4 +1,5 @@
.. SPDX-License-Identifier: GPL-2.0+
+
======================================================
IBM Virtual Management Channel Kernel Driver (IBMVMC)
======================================================
diff --git a/Documentation/misc-devices/ics932s401 b/Documentation/misc-devices/ics932s401.rst
similarity index 94%
rename from Documentation/misc-devices/ics932s401
rename to Documentation/misc-devices/ics932s401.rst
index bdac67f..613ee54 100644
--- a/Documentation/misc-devices/ics932s401
+++ b/Documentation/misc-devices/ics932s401.rst
@@ -1,10 +1,15 @@
+========================
Kernel driver ics932s401
-======================
+========================
Supported chips:
+
* IDT ICS932S401
+
Prefix: 'ics932s401'
+
Addresses scanned: I2C 0x69
+
Datasheet: Publicly available at the IDT website
Author: Darrick J. Wong
diff --git a/Documentation/misc-devices/index.rst b/Documentation/misc-devices/index.rst
new file mode 100644
index 0000000..f11c5da
--- /dev/null
+++ b/Documentation/misc-devices/index.rst
@@ -0,0 +1,23 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+============================================
+Assorted Miscellaneous Devices Documentation
+============================================
+
+This documentation contains information for assorted devices that do not
+fit into other categories.
+
+.. class:: toc-title
+
+ Table of contents
+
+.. toctree::
+ :maxdepth: 2
+
+ eeprom
+ ibmvmc
+ ics932s401
+ isl29003
+ lis3lv02d
+ max6875
+ xilinx_sdfec
diff --git a/Documentation/misc-devices/isl29003 b/Documentation/misc-devices/isl29003.rst
similarity index 76%
rename from Documentation/misc-devices/isl29003
rename to Documentation/misc-devices/isl29003.rst
index 80b952f..0cc38ae 100644
--- a/Documentation/misc-devices/isl29003
+++ b/Documentation/misc-devices/isl29003.rst
@@ -1,10 +1,15 @@
+======================
Kernel driver isl29003
-=====================
+======================
Supported chips:
+
* Intersil ISL29003
+
Prefix: 'isl29003'
+
Addresses scanned: none
+
Datasheet:
http://www.intersil.com/data/fn/fn7464.pdf
@@ -37,25 +42,33 @@
-------------
range:
+ == ===========================
0: 0 lux to 1000 lux (default)
1: 0 lux to 4000 lux
2: 0 lux to 16,000 lux
3: 0 lux to 64,000 lux
+ == ===========================
resolution:
+ == =====================
0: 2^16 cycles (default)
1: 2^12 cycles
2: 2^8 cycles
3: 2^4 cycles
+ == =====================
mode:
+ == =================================================
0: diode1's current (unsigned 16bit) (default)
1: diode1's current (unsigned 16bit)
2: difference between diodes (l1 - l2, signed 15bit)
+ == =================================================
power_state:
+ == =================================================
0: device is disabled (default)
1: device is enabled
+ == =================================================
lux (read only):
returns the value from the last sensor reading
diff --git a/Documentation/misc-devices/lis3lv02d b/Documentation/misc-devices/lis3lv02d.rst
similarity index 90%
rename from Documentation/misc-devices/lis3lv02d
rename to Documentation/misc-devices/lis3lv02d.rst
index f89960a..959bd2b 100644
--- a/Documentation/misc-devices/lis3lv02d
+++ b/Documentation/misc-devices/lis3lv02d.rst
@@ -1,3 +1,4 @@
+=======================
Kernel driver lis3lv02d
=======================
@@ -8,8 +9,8 @@
LIS331DLH (16 bits)
Authors:
- Yan Burman <burman.yan@gmail.com>
- Eric Piel <eric.piel@tremplin-utc.net>
+ - Yan Burman <burman.yan@gmail.com>
+ - Eric Piel <eric.piel@tremplin-utc.net>
Description
@@ -25,11 +26,15 @@
to mg values (1/1000th of earth gravity).
Sysfs attributes under /sys/devices/platform/lis3lv02d/:
-position - 3D position that the accelerometer reports. Format: "(x,y,z)"
-rate - read reports the sampling rate of the accelerometer device in HZ.
+
+position
+ - 3D position that the accelerometer reports. Format: "(x,y,z)"
+rate
+ - read reports the sampling rate of the accelerometer device in HZ.
write changes sampling rate of the accelerometer device.
Only values which are supported by HW are accepted.
-selftest - performs selftest for the chip as specified by chip manufacturer.
+selftest
+ - performs selftest for the chip as specified by chip manufacturer.
This driver also provides an absolute input class device, allowing
the laptop to act as a pinball machine-esque joystick. Joystick device can be
@@ -69,11 +74,12 @@
For better compatibility between the various laptops. The values reported by
the accelerometer are converted into a "standard" organisation of the axes
(aka "can play neverball out of the box"):
+
* When the laptop is horizontal the position reported is about 0 for X and Y
- and a positive value for Z
+ and a positive value for Z
* If the left side is elevated, X increases (becomes positive)
* If the front side (where the touchpad is) is elevated, Y decreases
- (becomes negative)
+ (becomes negative)
* If the laptop is put upside-down, Z becomes negative
If your laptop model is not recognized (cf "dmesg"), you can send an
diff --git a/Documentation/misc-devices/max6875 b/Documentation/misc-devices/max6875.rst
similarity index 83%
rename from Documentation/misc-devices/max6875
rename to Documentation/misc-devices/max6875.rst
index 2f2bd0b..ad419ac 100644
--- a/Documentation/misc-devices/max6875
+++ b/Documentation/misc-devices/max6875.rst
@@ -1,12 +1,16 @@
+=====================
Kernel driver max6875
=====================
Supported chips:
+
* Maxim MAX6874, MAX6875
+
Prefix: 'max6875'
+
Addresses scanned: None (see below)
- Datasheet:
- http://pdfserv.maxim-ic.com/en/ds/MAX6874-MAX6875.pdf
+
+ Datasheet: http://pdfserv.maxim-ic.com/en/ds/MAX6874-MAX6875.pdf
Author: Ben Gardner <bgardner@wabtec.com>
@@ -24,9 +28,13 @@
The Maxim MAX6874 is a similar, mostly compatible device, with more inputs
and outputs:
- vin gpi vout
+
+=========== === === ====
+- vin gpi vout
+=========== === === ====
MAX6874 6 4 8
MAX6875 4 3 5
+=========== === === ====
See the datasheet for more information.
@@ -41,13 +49,16 @@
---------------
Valid addresses for the MAX6875 are 0x50 and 0x52.
+
Valid addresses for the MAX6874 are 0x50, 0x52, 0x54 and 0x56.
+
The driver does not probe any address, so you explicitly instantiate the
devices.
-Example:
-$ modprobe max6875
-$ echo max6875 0x50 > /sys/bus/i2c/devices/i2c-0/new_device
+Example::
+
+ $ modprobe max6875
+ $ echo max6875 0x50 > /sys/bus/i2c/devices/i2c-0/new_device
The MAX6874/MAX6875 ignores address bit 0, so this driver attaches to multiple
addresses. For example, for address 0x50, it also reserves 0x51.
@@ -58,52 +69,67 @@
----------------------------------
Use the i2c-dev interface to access and program the chips.
+
Reads and writes are performed differently depending on the address range.
The configuration registers are at addresses 0x00 - 0x45.
+
Use i2c_smbus_write_byte_data() to write a register and
i2c_smbus_read_byte_data() to read a register.
+
The command is the register number.
Examples:
-To write a 1 to register 0x45:
+
+To write a 1 to register 0x45::
+
i2c_smbus_write_byte_data(fd, 0x45, 1);
-To read register 0x45:
+To read register 0x45::
+
value = i2c_smbus_read_byte_data(fd, 0x45);
The configuration EEPROM is at addresses 0x8000 - 0x8045.
+
The user EEPROM is at addresses 0x8100 - 0x82ff.
Use i2c_smbus_write_word_data() to write a byte to EEPROM.
The command is the upper byte of the address: 0x80, 0x81, or 0x82.
-The data word is the lower part of the address or'd with data << 8.
+The data word is the lower part of the address or'd with data << 8::
+
cmd = address >> 8;
val = (address & 0xff) | (data << 8);
Example:
-To write 0x5a to address 0x8003:
+
+To write 0x5a to address 0x8003::
+
i2c_smbus_write_word_data(fd, 0x80, 0x5a03);
Reading data from the EEPROM is a little more complicated.
+
Use i2c_smbus_write_byte_data() to set the read address and then
i2c_smbus_read_byte() or i2c_smbus_read_i2c_block_data() to read the data.
Example:
-To read data starting at offset 0x8100, first set the address:
+
+To read data starting at offset 0x8100, first set the address::
+
i2c_smbus_write_byte_data(fd, 0x81, 0x00);
-And then read the data
+And then read the data::
+
value = i2c_smbus_read_byte(fd);
- or
+or::
count = i2c_smbus_read_i2c_block_data(fd, 0x84, 16, buffer);
The block read should read 16 bytes.
+
0x84 is the block read command.
See the datasheet for more details.
diff --git a/Documentation/misc-devices/mei/mei-client-bus.txt b/Documentation/misc-devices/mei/mei-client-bus.txt
deleted file mode 100644
index 743be4e..0000000
--- a/Documentation/misc-devices/mei/mei-client-bus.txt
+++ /dev/null
@@ -1,141 +0,0 @@
-Intel(R) Management Engine (ME) Client bus API
-==============================================
-
-
-Rationale
-=========
-
-MEI misc character device is useful for dedicated applications to send and receive
-data to the many FW appliance found in Intel's ME from the user space.
-However for some of the ME functionalities it make sense to leverage existing software
-stack and expose them through existing kernel subsystems.
-
-In order to plug seamlessly into the kernel device driver model we add kernel virtual
-bus abstraction on top of the MEI driver. This allows implementing linux kernel drivers
-for the various MEI features as a stand alone entities found in their respective subsystem.
-Existing device drivers can even potentially be re-used by adding an MEI CL bus layer to
-the existing code.
-
-
-MEI CL bus API
-==============
-
-A driver implementation for an MEI Client is very similar to existing bus
-based device drivers. The driver registers itself as an MEI CL bus driver through
-the mei_cl_driver structure:
-
-struct mei_cl_driver {
- struct device_driver driver;
- const char *name;
-
- const struct mei_cl_device_id *id_table;
-
- int (*probe)(struct mei_cl_device *dev, const struct mei_cl_id *id);
- int (*remove)(struct mei_cl_device *dev);
-};
-
-struct mei_cl_id {
- char name[MEI_NAME_SIZE];
- kernel_ulong_t driver_info;
-};
-
-The mei_cl_id structure allows the driver to bind itself against a device name.
-
-To actually register a driver on the ME Client bus one must call the mei_cl_add_driver()
-API. This is typically called at module init time.
-
-Once registered on the ME Client bus, a driver will typically try to do some I/O on
-this bus and this should be done through the mei_cl_send() and mei_cl_recv()
-routines. The latter is synchronous (blocks and sleeps until data shows up).
-In order for drivers to be notified of pending events waiting for them (e.g.
-an Rx event) they can register an event handler through the
-mei_cl_register_event_cb() routine. Currently only the MEI_EVENT_RX event
-will trigger an event handler call and the driver implementation is supposed
-to call mei_recv() from the event handler in order to fetch the pending
-received buffers.
-
-
-Example
-=======
-
-As a theoretical example let's pretend the ME comes with a "contact" NFC IP.
-The driver init and exit routines for this device would look like:
-
-#define CONTACT_DRIVER_NAME "contact"
-
-static struct mei_cl_device_id contact_mei_cl_tbl[] = {
- { CONTACT_DRIVER_NAME, },
-
- /* required last entry */
- { }
-};
-MODULE_DEVICE_TABLE(mei_cl, contact_mei_cl_tbl);
-
-static struct mei_cl_driver contact_driver = {
- .id_table = contact_mei_tbl,
- .name = CONTACT_DRIVER_NAME,
-
- .probe = contact_probe,
- .remove = contact_remove,
-};
-
-static int contact_init(void)
-{
- int r;
-
- r = mei_cl_driver_register(&contact_driver);
- if (r) {
- pr_err(CONTACT_DRIVER_NAME ": driver registration failed\n");
- return r;
- }
-
- return 0;
-}
-
-static void __exit contact_exit(void)
-{
- mei_cl_driver_unregister(&contact_driver);
-}
-
-module_init(contact_init);
-module_exit(contact_exit);
-
-And the driver's simplified probe routine would look like that:
-
-int contact_probe(struct mei_cl_device *dev, struct mei_cl_device_id *id)
-{
- struct contact_driver *contact;
-
- [...]
- mei_cl_enable_device(dev);
-
- mei_cl_register_event_cb(dev, contact_event_cb, contact);
-
- return 0;
-}
-
-In the probe routine the driver first enable the MEI device and then registers
-an ME bus event handler which is as close as it can get to registering a
-threaded IRQ handler.
-The handler implementation will typically call some I/O routine depending on
-the pending events:
-
-#define MAX_NFC_PAYLOAD 128
-
-static void contact_event_cb(struct mei_cl_device *dev, u32 events,
- void *context)
-{
- struct contact_driver *contact = context;
-
- if (events & BIT(MEI_EVENT_RX)) {
- u8 payload[MAX_NFC_PAYLOAD];
- int payload_size;
-
- payload_size = mei_recv(dev, payload, MAX_NFC_PAYLOAD);
- if (payload_size <= 0)
- return;
-
- /* Hook to the NFC subsystem */
- nfc_hci_recv_frame(contact->hdev, payload, payload_size);
- }
-}
diff --git a/Documentation/misc-devices/mei/mei.txt b/Documentation/misc-devices/mei/mei.txt
deleted file mode 100644
index 2b80a0c..0000000
--- a/Documentation/misc-devices/mei/mei.txt
+++ /dev/null
@@ -1,266 +0,0 @@
-Intel(R) Management Engine Interface (Intel(R) MEI)
-===================================================
-
-Introduction
-============
-
-The Intel Management Engine (Intel ME) is an isolated and protected computing
-resource (Co-processor) residing inside certain Intel chipsets. The Intel ME
-provides support for computer/IT management features. The feature set
-depends on the Intel chipset SKU.
-
-The Intel Management Engine Interface (Intel MEI, previously known as HECI)
-is the interface between the Host and Intel ME. This interface is exposed
-to the host as a PCI device. The Intel MEI Driver is in charge of the
-communication channel between a host application and the Intel ME feature.
-
-Each Intel ME feature (Intel ME Client) is addressed by a GUID/UUID and
-each client has its own protocol. The protocol is message-based with a
-header and payload up to 512 bytes.
-
-Prominent usage of the Intel ME Interface is to communicate with Intel(R)
-Active Management Technology (Intel AMT) implemented in firmware running on
-the Intel ME.
-
-Intel AMT provides the ability to manage a host remotely out-of-band (OOB)
-even when the operating system running on the host processor has crashed or
-is in a sleep state.
-
-Some examples of Intel AMT usage are:
- - Monitoring hardware state and platform components
- - Remote power off/on (useful for green computing or overnight IT
- maintenance)
- - OS updates
- - Storage of useful platform information such as software assets
- - Built-in hardware KVM
- - Selective network isolation of Ethernet and IP protocol flows based
- on policies set by a remote management console
- - IDE device redirection from remote management console
-
-Intel AMT (OOB) communication is based on SOAP (deprecated
-starting with Release 6.0) over HTTP/S or WS-Management protocol over
-HTTP/S that are received from a remote management console application.
-
-For more information about Intel AMT:
-http://software.intel.com/sites/manageability/AMT_Implementation_and_Reference_Guide
-
-
-Intel MEI Driver
-================
-
-The driver exposes a misc device called /dev/mei.
-
-An application maintains communication with an Intel ME feature while
-/dev/mei is open. The binding to a specific feature is performed by calling
-MEI_CONNECT_CLIENT_IOCTL, which passes the desired UUID.
-The number of instances of an Intel ME feature that can be opened
-at the same time depends on the Intel ME feature, but most of the
-features allow only a single instance.
-
-The Intel AMT Host Interface (Intel AMTHI) feature supports multiple
-simultaneous user connected applications. The Intel MEI driver
-handles this internally by maintaining request queues for the applications.
-
-The driver is transparent to data that are passed between firmware feature
-and host application.
-
-Because some of the Intel ME features can change the system
-configuration, the driver by default allows only a privileged
-user to access it.
-
-A code snippet for an application communicating with Intel AMTHI client:
-
- struct mei_connect_client_data data;
- fd = open(MEI_DEVICE);
-
- data.d.in_client_uuid = AMTHI_UUID;
-
- ioctl(fd, IOCTL_MEI_CONNECT_CLIENT, &data);
-
- printf("Ver=%d, MaxLen=%ld\n",
- data.d.in_client_uuid.protocol_version,
- data.d.in_client_uuid.max_msg_length);
-
- [...]
-
- write(fd, amthi_req_data, amthi_req_data_len);
-
- [...]
-
- read(fd, &amthi_res_data, amthi_res_data_len);
-
- [...]
- close(fd);
-
-
-IOCTL
-=====
-
-The Intel MEI Driver supports the following IOCTL commands:
- IOCTL_MEI_CONNECT_CLIENT Connect to firmware Feature (client).
-
- usage:
- struct mei_connect_client_data clientData;
- ioctl(fd, IOCTL_MEI_CONNECT_CLIENT, &clientData);
-
- inputs:
- mei_connect_client_data struct contain the following
- input field:
-
- in_client_uuid - UUID of the FW Feature that needs
- to connect to.
- outputs:
- out_client_properties - Client Properties: MTU and Protocol Version.
-
- error returns:
- EINVAL Wrong IOCTL Number
- ENODEV Device or Connection is not initialized or ready.
- (e.g. Wrong UUID)
- ENOMEM Unable to allocate memory to client internal data.
- EFAULT Fatal Error (e.g. Unable to access user input data)
- EBUSY Connection Already Open
-
- Notes:
- max_msg_length (MTU) in client properties describes the maximum
- data that can be sent or received. (e.g. if MTU=2K, can send
- requests up to bytes 2k and received responses up to 2k bytes).
-
- IOCTL_MEI_NOTIFY_SET: enable or disable event notifications
-
- Usage:
- uint32_t enable;
- ioctl(fd, IOCTL_MEI_NOTIFY_SET, &enable);
-
- Inputs:
- uint32_t enable = 1;
- or
- uint32_t enable[disable] = 0;
-
- Error returns:
- EINVAL Wrong IOCTL Number
- ENODEV Device is not initialized or the client not connected
- ENOMEM Unable to allocate memory to client internal data.
- EFAULT Fatal Error (e.g. Unable to access user input data)
- EOPNOTSUPP if the device doesn't support the feature
-
- Notes:
- The client must be connected in order to enable notification events
-
-
- IOCTL_MEI_NOTIFY_GET : retrieve event
-
- Usage:
- uint32_t event;
- ioctl(fd, IOCTL_MEI_NOTIFY_GET, &event);
-
- Outputs:
- 1 - if an event is pending
- 0 - if there is no even pending
-
- Error returns:
- EINVAL Wrong IOCTL Number
- ENODEV Device is not initialized or the client not connected
- ENOMEM Unable to allocate memory to client internal data.
- EFAULT Fatal Error (e.g. Unable to access user input data)
- EOPNOTSUPP if the device doesn't support the feature
-
- Notes:
- The client must be connected and event notification has to be enabled
- in order to receive an event
-
-
-Intel ME Applications
-=====================
-
- 1) Intel Local Management Service (Intel LMS)
-
- Applications running locally on the platform communicate with Intel AMT Release
- 2.0 and later releases in the same way that network applications do via SOAP
- over HTTP (deprecated starting with Release 6.0) or with WS-Management over
- SOAP over HTTP. This means that some Intel AMT features can be accessed from a
- local application using the same network interface as a remote application
- communicating with Intel AMT over the network.
-
- When a local application sends a message addressed to the local Intel AMT host
- name, the Intel LMS, which listens for traffic directed to the host name,
- intercepts the message and routes it to the Intel MEI.
- For more information:
- http://software.intel.com/sites/manageability/AMT_Implementation_and_Reference_Guide
- Under "About Intel AMT" => "Local Access"
-
- For downloading Intel LMS:
- http://software.intel.com/en-us/articles/download-the-latest-intel-amt-open-source-drivers/
-
- The Intel LMS opens a connection using the Intel MEI driver to the Intel LMS
- firmware feature using a defined UUID and then communicates with the feature
- using a protocol called Intel AMT Port Forwarding Protocol (Intel APF protocol).
- The protocol is used to maintain multiple sessions with Intel AMT from a
- single application.
-
- See the protocol specification in the Intel AMT Software Development Kit (SDK)
- http://software.intel.com/sites/manageability/AMT_Implementation_and_Reference_Guide
- Under "SDK Resources" => "Intel(R) vPro(TM) Gateway (MPS)"
- => "Information for Intel(R) vPro(TM) Gateway Developers"
- => "Description of the Intel AMT Port Forwarding (APF) Protocol"
-
- 2) Intel AMT Remote configuration using a Local Agent
-
- A Local Agent enables IT personnel to configure Intel AMT out-of-the-box
- without requiring installing additional data to enable setup. The remote
- configuration process may involve an ISV-developed remote configuration
- agent that runs on the host.
- For more information:
- http://software.intel.com/sites/manageability/AMT_Implementation_and_Reference_Guide
- Under "Setup and Configuration of Intel AMT" =>
- "SDK Tools Supporting Setup and Configuration" =>
- "Using the Local Agent Sample"
-
- An open source Intel AMT configuration utility, implementing a local agent
- that accesses the Intel MEI driver, can be found here:
- http://software.intel.com/en-us/articles/download-the-latest-intel-amt-open-source-drivers/
-
-
-Intel AMT OS Health Watchdog
-============================
-
-The Intel AMT Watchdog is an OS Health (Hang/Crash) watchdog.
-Whenever the OS hangs or crashes, Intel AMT will send an event
-to any subscriber to this event. This mechanism means that
-IT knows when a platform crashes even when there is a hard failure on the host.
-
-The Intel AMT Watchdog is composed of two parts:
- 1) Firmware feature - receives the heartbeats
- and sends an event when the heartbeats stop.
- 2) Intel MEI iAMT watchdog driver - connects to the watchdog feature,
- configures the watchdog and sends the heartbeats.
-
-The Intel iAMT watchdog MEI driver uses the kernel watchdog API to configure
-the Intel AMT Watchdog and to send heartbeats to it. The default timeout of the
-watchdog is 120 seconds.
-
-If the Intel AMT is not enabled in the firmware then the watchdog client won't enumerate
-on the me client bus and watchdog devices won't be exposed.
-
-
-Supported Chipsets
-==================
-
-7 Series Chipset Family
-6 Series Chipset Family
-5 Series Chipset Family
-4 Series Chipset Family
-Mobile 4 Series Chipset Family
-ICH9
-82946GZ/GL
-82G35 Express
-82Q963/Q965
-82P965/G965
-Mobile PM965/GM965
-Mobile GME965/GLE960
-82Q35 Express
-82G33/G31/P35/P31 Express
-82Q33 Express
-82X38/X48 Express
-
----
-linux-mei@linux.intel.com